Scribd Logo
Upload

Welcome to Scribd!

  • 324 views

    Toshiba Tec Recovery Quick Guide S PDF

    Uploaded by

    Ahmed
    This document provides a 4-step guide for recovering clogged print heads: 1. Reverse flush the print head using suction to remove severe clogs, then forward flush with recovery fluid. 2. Forward flush the print head using syphon cycles and gradually increasing temperature up to the maximum. 3. If no improvement, switch to the next higher numbered recovery fluid and repeat flushing. 4. Once recovered, flush the print head with the fluid that comes with the inks before reinstalling.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Toshiba Tec Recovery Quick Guide S PDF

    Uploaded by

    Ahmed
    324 views2 pages
    This document provides a 4-step guide for recovering clogged print heads: 1. Reverse flush the print head using suction to remove severe clogs, then forward flush with recovery fluid. 2. Forward flush the print head using syphon cycles and gradually increasing temperature up to the maximum. 3. If no improvement, switch to the next higher numbered recovery fluid and repeat flushing. 4. Once recovered, flush the print head with the fluid that comes with the inks before reinstalling.

    Original Title

    toshiba_tec_recovery_quick_guide_s.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides a 4-step guide for recovering clogged print heads: 1. Reverse flush the print head using suction to remove severe clogs, then forward flush with recovery fluid. 2. Forward flush the print head using syphon cycles and gradually increasing temperature up to the maximum. 3. If no improvement, switch to the next higher numbered recovery fluid and repeat flushing. 4. Once recovered, flush the print head with the fluid that comes with the inks before reinstalling.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    324 views2 pages

    Toshiba Tec Recovery Quick Guide S PDF

    Uploaded by

    Ahmed
    This document provides a 4-step guide for recovering clogged print heads: 1. Reverse flush the print head using suction to remove severe clogs, then forward flush with recovery fluid. 2. Forward flush the print head using syphon cycles and gradually increasing temperature up to the maximum. 3. If no improvement, switch to the next higher numbered recovery fluid and repeat flushing. 4. Once recovered, flush the print head with the fluid that comes with the inks before reinstalling.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Toshiba Tec CA3/CA4/CA5/CE2

    Print Head Recovery Quick Guide


    Step 1. Reverse Flush the print head
    This step is required for severely clogged print heads. You may skip this step and get back to it later if you dont have a satisfactory results from
    the Forward Flushing methods. Use a suction method of reverse flushing as shown here. Run Syphon cycle. After its completed, set up your
    print head for Forward Flushing and run it with Syphon cycle again. Use fluid # 1UV if you are cleaning a UV print head, or fluid # 1X for solvent
    print head, or fluid # 1W for water-based one. Temperature can be 30-35C. Do not exceed Max Temperature indicated on the picture.
    Remember that the temperature will rise due to the ultrasonic power.
    Step 2. Forward Flush the print head
    Set up your print head for forward flushing as shown on the picture below. Run Syphon cycle only. Start with temperature of 30C. After the
    cycle has been finished, run Drain cycle (to turn on the pumps) and check nozzles. If there is improvement, repeat the cycle with a slightly
    higher temperature. Do not exceed Maximum Temperature.
    Step 3. Proceed with Forward Flushing
    If you dont see improvements in the nozzles condition, move on to the next fluid (the fluid with the next number). When changing fluids,
    follow instructions from our videos. Set temperature to 30C and go to Step 2.
    Step 4. Flushing print head with the Flush that comes with your inks
    After the print head has been recovered, fill it with the Intermediate Fluid (also called Storage Fluid). Purge it out with air. Then, fill the
    print head with flushing solution that comes with your ink. Check if the nozzles are still open by slowly pushing your fluid with a syringe. If
    they are clean, the print head can be installed on a printer.
    Important: do not leave recovery fluids with number higher than 1 inside the machine overnight. They will affect the pumps. Always drain
    the fluid and run distilled water through the machine for 1 minute, then purge the water out by allowing the machine to suck in the air and by
    running the AR cycle for a few seconds.

    Toshiba Tec CA3 / CA4 / CA5

    Toshiba Tec CE2

    Mimaki UV Print Head (Toshiba CA4)

    Outputs

    Forward Flushing
    Toshiba Print Head

    MAX

    PRESSURE

    0.10
    MPa

    Maximum pressure
    0.10 Mpa / 15 psi
    Inputs

    15
    psi

    Adjust pressure
    with Relief Valve

    Print Head

    Maximum

    Recovery Fluid

    Temperature

    Tank

    45C

    1. Connect print head as shown.


    2. Install input filter(s)
    3. Partially open the Relief Valve.
    4. Start Syphon or Normal cycle.
    5. Keep pressure within limits.
    6. Do not exceed Max Temperature.

    Inputs

    Outputs

    Reverse Flushing Toshiba Tec


    print head using Suction Method

    Pressure at zero

    Relief valve open

    Print Head
    Recovery Fluid
    Tank

    Maximum
    Temperature

    40C

    1. Fluid and tank must be clean.


    2. Plug both output ports.
    3. Open Relief Valve (one turn).
    4. Fluid must reach Print head.
    5. Connect print head as shown.
    6. Run Syphon cycle.

    You might also like