Woven Shirt Measurement Method

VARDHMAN NISSHINBO GARMENT COMPANY LTD.
Woven Shirt Measurement Method
Objectives:
To serve as a general guideline when conducting measurement inspection of the garment when
buyers measurement is not available. All the measurement must meet the acceptable
tolerance set by the Customer as stated in the Customer Specs. Measurement should be taken
on a clean, flat and smooth surface. Garment is measured in the condition of button up unless
otherwise stated. Pleats must be open and smoothed of all wrinkles for accuracy.
Sr.
ITEM DESCRIPTION
&
SKETCH
INSTRUCTION
1
Collar Button To ButtonHole:

With collar laying flat,
measure along the center of
the collar stand
from the center of the
button to end of the
buttonhole
COLLAR HEIGHT CB
Measure from collar edge to
collar stand join seam at
center back.
COLLAR POINT:
Measure along the edge of
collar from point to seam.
QUALITY MANUAL
Page 1

4
NECK BAND HEIGHT:
Measure from collar join

seam to neck join seam at
center back.
NECK BAND PEAK

SQUARE / ROUND ):
Measure from end of collar

stand to the end of the
collar.
Collar Spread:
Measure distance of collar
point to point with garment
laying flat.
Tie Space:
With shirt buttoned and
laying flat, measure space
from collar join seam to
collar join seam at front.
QUALITY MANUAL
Page 2

8
HALF CHEST 2.5 CM BELOW

ARMHOLE:
Measure 1 inch below
armhole and then straight
across from edge to edge.
HALF WAIST 20CM BELOW

ARMHOLE:
Measure at the narrowest
point between chest and
sweep from edge to edge.
QUALITY MANUAL
Page 3

10
HALF BOTTOM HEM:
Measure straight across

from edge to edge
11
SHOULDER
12
CB YOKE HEIGHT:
Measure from center back
neck seam straight down to
bottom of yoke.
13
ACROSS SHOULDER:
from top of left armhole
seam to top of right armhole
seam.
14
ACROSS BACK YOKE AT

SEAM:
from top of left armhole
seam to top of right armhole
seam.
QUALITY MANUAL
Page 4

15
HALF ARM HOLE CURVED:
Lay garment flat, aligning

the front and back armhole
seams, and position the
sleeve so that the armhole
seam has no wrinkles. Then
measure, following the
armhole seam curve from
top to bottom.
16
F/S LENGTH INCLUDUNG

CUFF:
Measure the points starting
at armhole seam to straight
down outside of the sleeve
fold to bottom edge.
17
H/S LENGTH:
Measure the points starting
at armhole seam to straight
down outside of the sleeve
fold to bottom edge
QUALITY MANUAL
Page 5

18
SLEEVE PLACKET LENGTH:
Measure from top edge of

placket to cuff join seam.
19
SLEEVE PLACKET WIDTH:

Measure edge to edge.
20
SLEEVE BOX (FIRST &

SECOND LINE):
QUALITY MANUAL
Page 6

21
HALF SLEEVE OPEN ( 1/2 ):
Measure along opening,

edge to edge.
22
HALF SLEEVE HEM:

Measure from stitch line to
bottom edge.
23
CUFF EDGE TO EDGE:

Unbutton cuff and measure
from edge to edge.
24
CUFF HEIGHT:
Measure from bottom edge
to top edge.
QUALITY MANUAL
Page 7

25
CUFF PLEAT ( FIRST &

SECOND):
Measure from the edge of

diamond placket to the
crease of the pleats
26
BACK LENGTH:
Measure from center back
neck seam straight down to
the bottom edge.
QUALITY MANUAL
Page 8

27
FRONT PLACKET WIDTH:
Measured from edge to

edge, or edge to stitch line,
and for faced plackets
measure from the inside
facing edge to edge.
28
BUTTON PLACKET WIDTH:

Measured from edge to
edge, or edge to stitch line,
and for faced plackets
measure from the inside
facing edge to edge
QUALITY MANUAL
Page 9

29
POCKET PLACMENT FROM

SHOULDER POINT:
Front shoulder seam where

it meets under collar, then
straight down to top of welt
pocket.
30
FRONT PLACKET END TO

POCKET:
Measure from placket edge
to the edge of the pocket.
QUALITY MANUAL
Page 10

31
POCKET LENGTH:
Measure from top edge of

pocket to lowest point of
pocket.
32
POCKET WIDTH:
Measure from edge to edge.
QUALITY MANUAL
Page 11

33
POCKET HEM:
Measure from the top of the

pocket to the stitch of the
hem.
34
FRONT LENGTH FROM

SHOULDER SEAM:
Measure from HPS neck join
seam to the bottom of the
garment keeping the tape
parallel to the center front.
If garment has a shirt tail,
measure to the imaginary
line of the lowest point.
QUALITY MANUAL
Page 12

35
Button Placement:
Measure from center button

to center of next button.
QUALITY MANUAL
Page 13

Woven Shirt Measurement Method

Uploaded by

Copyright:

Available Formats

Woven Shirt Measurement Method

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Woven Shirt Measurement Method

Uploaded by

Copyright:

Available Formats

What are the different measurements described in the manual?

What are the different measurements described in the manual?

What areas of the shirt are measured?

What areas of the shirt are measured?

VARDHMAN NISSHINBO GARMENT COMPANY LTD.