Soft Foot--What It Is and How to Minimize It

Search

About
Home

Troubleshooting

Belts & Sheaves

Dial Indicators

Equipment Type

Contact

Authors

News & Events

Installation and Best Practices

Training

VibrAlign Products

SOFT FOOTWHAT IT IS AND HOW TO MINIMIZE IT

By Brad Case in Bases, Featured, Machinery Installation and Best Practices, Shims, Soft
Foot
June 4th, 2010
Soft foot is a common issue when aligning rotating equipment. It is a major cause of repeatability
problems in shaft alignment measurements. In addition to alignment quality and repeatability problems,
it can be a cause of machinery vibration, reduce life in electric motors, and cause internal clearance
problems in gearboxes and pumps.
But if the proper precautions are taken, soft foot can be minimized and controlled.
The term soft foot is the common term used for the improper contact between a machine casing, and
the baseplate used to support it. It may be either an angular or parallel soft foot, but often it is a
combination of the two.

It is often compared to a straight-backed wooden chair, where one leg, being shorter, does not contact
the floor, causing a rocking motion in the chair when you are seated in it. While this is a good mental
image, soft foot in machinery is a little more complex. While an angular soft foot might make contact
with a baseplate or foundation, it does not make a UNIFORM amount of contact. Once base bolts are
tightened, the foot tends to bend to conform to the baseplate to which it is mounted.
CAUSES OF SOFT FOOT CONDITIONS
Twisted or warped machinery foundations or baseplates.
Twisted, warped, or damaged machinery feet.
Improper amount of shims under machine feet.
Dirt, trash, or other unwanted materials under machine feet.
Dents or other flaws in machine base or machine feet.
Excessive tension on machine feet due to jack bolts warping the machine feet.
WHAT SOFT FOOT DOES TO YOUR ALIGNMENTS
As stated above, soft foot conditions adversely affect alignment quality and repeatability. Heres how:
Regardless of whether you have:
an angular or parallel soft foot,
a bent or deformed shim,
a bolt hole with a burr,
a bent motor foot,
a deformed machine base,
it can cause the same type of problem. Once you tighten the bolt where the soft foot is, you change
the relative position of the shaft. In other words, the position of the shaft changes between tight and

http://thealignmentblog.com/blog/2010/06/04/soft-foot-what-it-is-and-how-to-minimize-it/[29/05/2013 03:34:10]

Glossary

Soft Foot--What It Is and How to Minimize It

loose. If you have used laser alignment tools, you might have noticed that there is sometimes a foot
that causes a noticeable change in the vertical or horizontal readings as you tighten a particular bolt.
Often, this is the location of the soft foot condition.

Notice that the relative position of the shaft centerline changes due to changes in the position of the
soft foot.
In addition, unless you tighten and loosen the bolts in sequence, the position of the shaft centerline in
relation to the stationary machine can change. As an example, if you tighten the inboard left foot first
one time, and the inboard right foot the second time, you may take measurements in different shaft
centerline locations. Using the straight-backed chair analogy, not tightening in a known sequence
causes the movable machine to rock into different positions.
STEPS TO MINIMIZE AND CONTROL SOFT FOOT
Confirm that base plates and foundations are installed and leveled to specifications.
Make sure that baseplates and machine feet are clean, deburred and free from dents in the areas
to which machinery will be mounted.
Use clean, flat shims. If you must cut thicker shims from steel stock, be sure they are clean, flat
and deburred.
Once the machine components are placed on the baseplate, rough align, and perform a gross soft
foot check of both the movable and stationary machines.
Leave all foot bolts loose
Check one foot at a time, on at least three corners of each foot, with a 0.005 shim or feeler
gauge. Correct by shimming with the minimum number of shims possible. If an angular soft foot
condition exists, cut one shim in half, leaving the tab in place, to make it easier to reposition.
Do not attempt to cut several shims to step the shim thicknesses under a particular foot. While
this might seem like a good idea to increase the amount of contact area, it becomes much more
complicated to reposition several shims each time.
Once gross soft foot has been corrected, tighten each bolt, using a bolt torque pattern similar to the
diagram below. The starting point can be any foot, as long as the same pattern is followed EACH
TIME the feet are loosened and tightened.

Once all bolts are tight, loosen one foot, and recheck for soft foot with a 0.002 shim or feeler
gauge. Repeat the process of checking each foot at three corners, to identify angular soft foot.
Shim to correct as needed. Then retighten the foot and move to the next one. Repeat this process
until all feet have been checked and shimmed as needed.
Tighten foot bolts using 3 passes and following the same bolt torque pattern on each pass. 1 st
pass tighten to hand tight. 2 nd pass tighten the bolts, using a wrench, to around 50% tightness. 3 rd
pass, complete tightening the bolts. This will minimize the effect of any remaining soft foot.
Additional soft foot checks can be done using laser alignment tools that have soft foot check

http://thealignmentblog.com/blog/2010/06/04/soft-foot-what-it-is-and-how-to-minimize-it/[29/05/2013 03:34:10]

Soft Foot--What It Is and How to Minimize It

capability or with dial indicators. But be mindful that soft foot can not only be in the machine foot
it can also be in the baseplate to which the machine is mounted. In other words, when you loosen
the foot bolt, the machine foot may not move, but the base or support underneath it might. This
can happen when the foot of the machine you are aligning is thicker than the base or riser onto
which it sits. In the example below, if the motor feet are tightened, the base may bend upward to
contact the thicker motor foot.

If the base moves up to contact the motor foot, you may not be able to measure it with a laser
alignment tool, or a dial indicator, but it might still cause a soft foot response in the movement of
the motor. A shim or feeler gauge is preferred to determine and correct this type of soft foot.

Share:

Facebook

Tweet

14

Share

Email

Print

Tags: "soft foot"

About the Author

Brad Case
Brad Case has been associated with VibrAlign since 1990, first as a manufacturer's
representative, then joining the company as a direct employee in 2005. He has 25 years
experience in aligning industrial machinery. Brad began his career in the automotive
industry providing technical training, sales, and service for Murray Goldseal an aftermarket
air conditioning component manufacturer. His background includes 25 plus years
experience in sales, service and training for centralized lubrication systems (including
large scale oil mist applications in petrochemical facilities), couplings, gearing, and gear
reducers. Brad and his wife currently live in Allen, TX.

7 Comments
Marc
March 21, 2013 at 4:07 am
Brad,
I have a doubt. I am doing pump alignment. The soft foot & pre-alignment without flange
bolting is within tolerance .005mm. Then bolts were tighten, the offset & angular on the vertical
position / movement is within tolerance (0.005) but the soft foot/shim value at far end of motor
has increased to .008. Is this acceptable as long as the offset & angular value is alright or we
have to adjsut the shims again.
Thanks.
Reply

D Mike Minks
April 11, 2013 at 12:36 pm
Marc. soft foot check is the first thing you look for when initially installing a motor/pump

http://thealignmentblog.com/blog/2010/06/04/soft-foot-what-it-is-and-how-to-minimize-it/[29/05/2013 03:34:10]

Soft Foot--What It Is and How to Minimize It

configuration. The next is flange stresses. Most pump manufacturers have minimum
standards but if those were not stated either in the installation specifications or in
shipping documents, you should use the same standard the alignment standard of 2
mils.
This may require loosening of the expansion joints of the inlet and outlet piping. If not
installed, expansion joints may need to be installed to eliminate flange stresses. If these
stresses are left unattended, bearings and possibly pump internals may be out of
tolerance and cause premature failure.
Reply

naaz
March 8, 2013 at 2:17 pm
But in api stander half or cutting not allowed.then how can I remove angler softfoot?
Reply

Brad Case
March 13, 2013 at 12:18 am
Naaz,
You are correct. API 610 also specifies flatness tolerances for bases, machine pads, and
feet. All of which are well under the allowable soft foot tolerance, angled or otherwise.
If you have a machine with an angled soft foot that is more than the acceptable tolerance
(2 to 3 mils) and cant cut a shim in half to correct than a course of action to correct the
problem needs to be discussed with your engineering department as either the foot (or
base) in question may no longer meet the API flatness tolerances.
A short term solution maybe to temporarily allow a cut shim until a time when the
machine feet/base can be checked for flatness. You may also check into having a special
shim ground to a taper to match the angled soft foot.
Reply

S D banerjee
January 23, 2013 at 10:17 am
Is it essential to put shims between a gearbox and its bedplate to avoid vibrations due to soft
foot?
Reply

Stan Riddle
January 24, 2013 at 6:43 am
It is essential to minimize soft foot, so if it exists between the bedplate and the gearbox,
yes. Not only can it increase vibration, it can make alignment more difficult, and change
clearances within the gearbox, due to case distortion. Many of the gearboxes I have
installed need a slight amount of shimming due to irregularities in the baseplate.
Reply

Muhammad Hunain
December 19, 2012 at 1:38 pm

http://thealignmentblog.com/blog/2010/06/04/soft-foot-what-it-is-and-how-to-minimize-it/[29/05/2013 03:34:10]

Soft Foot--What It Is and How to Minimize It

I found this blog very helpful for me, i have some confusion regarding soft foot.
thanks.
Reply

Leave a comment
Name *
Email (will not be published) *
Website

Submit

Other Resources
The Alignment Resource
Center
Realigning America

Socialize

Training Events
July
May
May
May

23-24:
30-31:
28-29:
28-29:

Richmond, VA
Richmond, VA
Houston, TX
Richmond, VA

Subscribe to the Feed

Enter your email below to receive
email updates about new content
on The Alignment Blog.

Enter Email...

submit

Archives
May 2013

http://thealignmentblog.com/blog/2010/06/04/soft-foot-what-it-is-and-how-to-minimize-it/[29/05/2013 03:34:10]

Soft Foot--What It Is and How to Minimize It

April 2013
March 2013
February 2013
January 2013
December 2012
November 2012
October 2012
September 2012
August 2012

News & Events

VibrAlign is featured in a new
book, Grow Regardless
Video: Basic Concepts of
Rotating Machinery Shaft
Alignment
Free Laser-Dials Shaft
Alignment App
Launch of
CompressorAlignment.com
VibrAlign, Inc. Announces
New Blog

Related Posts
Shims 201 The
Importance of
Measuring Shim
Thickness
March 28th, 2013
Soft Foot Caused
by a C-face
Motor
February 12th,
2013
Does Using a
Torque Wrench
Make Shaft
Alignments More
Accurate?
November 4th, 2012

2013 Vibralign Inc. All rights reserved.

http://thealignmentblog.com/blog/2010/06/04/soft-foot-what-it-is-and-how-to-minimize-it/[29/05/2013 03:34:10]