PV Elite Webinar 001

Comparison of pressure vessel codes
Why do the codes differ and How do they differ
Presented by: Ray Delaforce
03/24/11
By
Ray Delaforce
3/24/2011
By Ray Delaforce
COMPARISON of the various pressure vessel codes

These are the codes we are going to compare:
ASME Section VIII, Division 1
ASME Section VIII, Division 2
PD 5500
EN 13445 Part 3
But first we look at the most fundamental requirement

What is the ALLOWABLE STRESS ?
y stress we must not exceed
This is the primary
A PRIMARY stress results from internal pressure
There are SECONDARY stresses we do not discuss them
03/24/11
By
Ray Delaforce
3/24/2011
By Ray Delaforce

We first look at a couple of important material properties
Let us look at the Stress-Strain diagram we get a lot of information
Collapse can occur when we reach the yield point
Let us look at the important features of our steel
Elastic
El
ti
Range
Plastic Range
Fracture
Ductile Range
Stre
ess
Yield Point
All
Allowable
bl Stresses
St
about
b t here
h
0.2% strain
Strain

Consider steel: UTS = 70 000 psi (482 MPa) Yield 38000 psi (262 MPa)
Let us look at the Stress-Strain diagram we get a lot of information
Collapse can occur when we reach the yield point
Let us look at the important features of our steel
There are three important features we must consider
1. There is the limit of proportionality
Yield Point 0.2% strain
2. The Ultimate Tensile Strength (UTS)
When fracture occurs
3. The Ductility = Yield / UTS
Must be less than 1.0
There is a 4th one Creep which occurs at higher temperatures

Allowable stress is base on these characteristics of the metal
ASME Section VIII Division 1
S
= smaller of:
UTS / 3.5
or
Yield / 1.5
= 20 000 psi (138 MPa)
or
Yield / 1.5
= 25 300 psi (174 MPa)
ASME Section VIII Division 2

Sm = smaller of:
EN 13445
f = smaller of:
UTS / 2.4
Both based on PED European requirements

UTS / 2.4
or
Yield / 1.5
= 25 300 psi (174 MPa)
PD 5500
f = smaller of:
UTS / 2.35 or
We consider Carbon Steel for simplicity
Yield / 1.5
= 25 300 psi (174 MPa)

We look at this on the Stress Strain diagram
ASME VIII, Division 1 has a larger safety margin safer
This code is still the favoured code throughout the World
Stre
ess
Yield Point
ASME VIII Division 2, EN 13445 & PD 5500
ASME VIII Di
Division
i i 1
Strain

Let us now look at a typical calculation the cylindrical shell
Here are the basic dimensions
We shall ignore joint efficiency E (z)
W now do
We
d the
th calculation
l l ti for
f the
th cylinder:
li d
P = 300 psi (207 MPa)
By ASME VIII Division 1
D = 60 ins (1 524 mm)

S(f) = 20 000 psi (174 MPa)
t = 0.454 in (11.534 mm)

t = 0.453 in (11.516 mm)
By EN 13445
DO Di
t ASME e EN 13445 & PD5500

Let us now look at a typical calculation the cylindrical
Elliptical Head
shell
We shall ignore joint efficiency E
W now do
We
d the
th calculation
l l ti for
f the
th cylinder:
li d
P = 300 psi (207 MPa)
D = 60 ins (1 524 mm)

S(f) = 20 000 psi (174 MPa)
t = 0.454 in (11.534 mm)

t = 0.453 in (11.516 mm)
That is why the differences

are so small the formulae
are nearly the same !
By EN 13445
t=0
0.453
453 iin (11
(11.516
516 mm))
This formula looks odd,

but is actually just about
the same as the others
By PD 5500
t=0
0.453
453 in (11
(11.516
516 mm)
8

Let us now look at a typical calculation the cylindrical
Elliptical Head
shell
We shall ignore joint efficiency E
W now do
We
d the
th calculation
l l ti for
f the
th cylinder:
li d
Cylinder based on the
equilibrium equation
t = 0.454 in (11.534 mm)

t = 0.453 in (11.516 mm)
That is why the differences

are so small the formulae
are nearly the same !
By EN 13445
t=0
0.453
453 iin (11
(11.516
516 mm))
This formula looks odd,

but is actually just about
the same as the others
By PD 5500
t=0
0.453
453 in (11
(11.516
516 mm)
9

Let us now look at a typical calculation the Elliptical Head
Minor
Shape is based on true ellipse

D/2h = 2
h
Major
D
ASME Division 1
2 simple
complicated
calculation
calc.
P = 300 psi (207 MPa)

D = 60 iins (1 524 mm))
S(f) = 20 000 psi (138 MPa)
t = 0.451 in
t = 11.447 mm
Head formula almost identical to the cylinder formula:

Cylinder:
Elliptical head:
10

Let us now look at a typical calculation the Elliptical Head
Minor
Shape is based on true ellipse

D/2h = 2
h
Major
D
ASME Division 2 complicated calc.
P = 300 psi (207 MPa)
1 There are many steps to do
D = 60 iins (1 524 mm))
2 Cannot calculate t directly . .

. only P
S(f) = 25 300 psi (174 MPa)
Division 2 allows higher stress

On the next slide we show the calculation per PV Elite
11

This is the calculation using PV Elite - ASME Division 2
The Elliptical head is transformed in equivalent Torispherical Head
Crown radius
Knuckle radius
12

Next we must calculate some geometry factors
13

Even more geometry and other factors
factors and more lots of factors
14

Even more geometry and other factors and more lots of factors
Finally we end up with our starting pressure
PV Elite does an iterative calculation to end up with the pressure
15

We had to start the calculate with a guess thickness t
And we ended up with our starting pressure
We have to use a computer to do this calculation !

The computed thickness is
t = 0.3219 in
t = 8.1767 mm
16

EN 13445 has a similar method slightly less complicated than ASME
The final computed thickness is: t = 0.3886 in
t = 9.8619 mm
17

The method of computing the head by PD 5500 is very different
Minor
1 Calculate h / D = 0.25
2 Calculate P / f = 0.119
h
Major
D
P = 300 psi (207 MPa)
D = 60 iins (1 524 mm))
f = 25 300 psi (174 MPa)
PD 5500 uses a graphical solutions like this
18

Here is the Graph used to compute this head thickness
1 Calculate h / D = 0.25
2 Calculate P / f = 0.119
e/D
e = D x (e/D)
19

This is the calculation using PV Elite
t = 0.3792 in
t = 9.6317 mm
Each code has its own way of computing a head and other parts
But, where do codes borrow procedures from other codes ?
20

Codes Copy codes some examples
Flange analysis
ASME Division 1
ASME Division 2
EN 13445-3
PD 5500
21

Access openings in skirt
AD Merblatter (AD 2000)
EN 13445-3
22

Pressure Area method
PD 5500
ASME Division 1
ASME Division 2
EN 13445-3
E h off the
Each
th codes
d has
h modified
difi d the
th method
th d same principle
i i l
23

PV Elite Webinar 001

Uploaded by

Copyright:

Available Formats

PV Elite Webinar 001

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PV Elite Webinar 001

Uploaded by

Copyright:

Available Formats

Comparison of pressure vessel codes

Why do the codes differ and How do they differ

Presented by: Ray Delaforce

COMPARISON of the various pressure vessel codes

But first we look at the most fundamental requirement

COMPARISON of the various pressure vessel codes

COMPARISON of the various pressure vessel codes

Yield Point 0.2% strain

2. The Ultimate Tensile Strength (UTS)

When fracture occurs

3. The Ductility = Yield / UTS

Must be less than 1.0

There is a 4th one Creep which occurs at higher temperatures

COMPARISON of the various pressure vessel codes

= 20 000 psi (138 MPa)

= 25 300 psi (174 MPa)

ASME Section VIII Division 2

Both based on PED European requirements

= 25 300 psi (174 MPa)

We consider Carbon Steel for simplicity

= 25 300 psi (174 MPa)

COMPARISON of the various pressure vessel codes

COMPARISON of the various pressure vessel codes

We shall ignore joint efficiency E (z)

By ASME VIII Division 1

D = 60 ins (1 524 mm)

t = 0.454 in (11.534 mm)

By ASME VIII Division 2

t ASME e EN 13445 & PD5500

COMPARISON of the various pressure vessel codes

We shall ignore joint efficiency E

By ASME VIII Division 1

D = 60 ins (1 524 mm)

t = 0.454 in (11.534 mm)

By ASME VIII Division 2

That is why the differences

This formula looks odd,

COMPARISON of the various pressure vessel codes

We shall ignore joint efficiency E

t = 0.454 in (11.534 mm)

By ASME VIII Division 2

That is why the differences

This formula looks odd,

COMPARISON of the various pressure vessel codes

Shape is based on true ellipse

P = 300 psi (207 MPa)

Head formula almost identical to the cylinder formula:

COMPARISON of the various pressure vessel codes

Shape is based on true ellipse

ASME Division 2 complicated calc.

P = 300 psi (207 MPa)

1 There are many steps to do

D = 60 iins (1 524 mm))

2 Cannot calculate t directly . .

S(f) = 25 300 psi (174 MPa)

Division 2 allows higher stress

COMPARISON of the various pressure vessel codes

COMPARISON of the various pressure vessel codes

COMPARISON of the various pressure vessel codes