BUCK AND BUCK-BOOST DC-DC CONVERTERS
I. OBJECTIVES
a) To visualize the waveforms for the voltages and currents from the dc-dc
converter circuits (Buck and Buck-boost).
b) To determine the parameters of the output voltages for the dc-dc converters.
II. COMPONENTS AND INSTRUMENTATION
We use the experimental assembly from Fig. 3, equipped with an
IRF9130 transistor (enhanced p channel MOS transistor), a diode, an
inductor, resistors and capacitors of different values. The positive voltage
supply is applied from a dc voltage supply, and the command voltage is
obtained from the signal generator. We use a dual channel oscilloscope to
visualize the signals, and a multimeter to measure the dc values.
III. PREPARATION
P1. Buck converter (Step down)
The output voltage of the Buck converter is lower than the input voltage.
For the circuit in Fig.1, supplied with VI=10V, controlled with a
rectangular signal vcmd from the function generator, with an amplitude of 10V,
frequency 33KHz and a duty cycle =50%, draw the waveforms of the
following signals:
o vI(t), vcmd(t), vD3(t), vO(t);
o iI(t), iD3(t), iL1(t), iC1(t).
Write the relationship between VO and VI and find the value of VO for
VI=10V and duty cycle =50%. The duty cycle is computed as =T L/T, where
TL represents the time during which the control signal is 0V (control transistor
M1 is in conduction state) and T is the period of the signal.
P2. Buck-Boost converter (Step down/step up)
The output voltage of a Buck Boost converter has an inverted polarity
compared with the input voltage.
For the circuit in Fig. 2, supplied with VI=10V, controlled with a
rectangular signal vcmd from the function generator, with an amplitude of 10V,
frequency 20KHz and a duty cycle =50%, draw the waveforms of the
following signals:
o vI(t), vcmd(t), vL2(t), vO(t);
o iI(t), iD3(t), iL2(t), iC2(t).
Write the relationship between VO and VI and find the value of VO for
VI=10V and duty cycle =50%.
IV. EXPLORATIONS AND RESULTS
1. Buck converter
1.1. Waveforms
Exploration
Supply the circuit in Fig.1 with VI=10V and connect a load resistance
RL1=50. You will do this by connecting J2 with J3, J4 with J5, J7
M1
IR F 9 1 3 0
L1
1m
D 3
M BR 040
VI
10Vdc
V1 = 0
C in
V2 = 10
TD = 0
1000u TR = 1n
TF = 1n
P W = 1 6 .7 u
P E R = 3 3 .3 u
C 1
220u
R L
Vcm d
50
R 4
1
Fig.1. Buck converter
with J8, J11 with J12 and R1 closed.
R 5
1
On the ground terminal of the control transistor M 1, apply a
rectangular signal vcmd from the function generator, with an amplitude
of 10V, frequency 33KHz and a duty cycle =50%.
Visualize the waveforms of the following signals:
o the control voltage vcmd (t) and the voltage on R4, vR4(t),
between J13 and GND (R4 acts like a current transducer for
iD3(t));
o the control voltage vcmd (t) and the voltage on R5, vR5(t)
between J14 and GND (R5 acts like a current transducer for
iC1(t));
o the control voltage vcmd (t) and the output voltage vO(t). The
output voltage is measured between OUT and GND, for J14
connected to the ground.
Results
Draw the waveforms for vcmd (t), vO(t), vL2(t), iRL(t), iC1(t), iL1(t), iD3(t)
and iI(t).
1.2. Verifying the relationship between the input and the output voltage
Exploration
Visualize the control voltage vcmd(t) and the output voltage vO(t), for
RL1=50 and compute VO/VI.
Modify the value of the input voltage and the amplitude of the control
voltage to 8V. Measure once again the output voltage and recompute
VO/VI.
Results
The value of VO/VI for VI=10V.
The value of VO/VI for VI=8V.
1.3. Variation of the output voltage ripple vO with load resistance
Exploration
For the circuit in Fig.1. with R L1 apply once again vcmd with a duty
cycle =50%. Copy the values for v O and vO you obtained in section
1.2.
At the output, replace the load resistance RL1 with RL2 = 75, by
disconnecting R1 and connecting the jumper on the R2 position.
Visualize the control and the output voltages, measure the output
voltage vO, as well as the variation of the output voltage, vO.
Results
The values of VO and vO for =50% (copied from section 1.2.)
Draw the waveforms for vcmd (t) and vO(t), for RL2.
The values of VO and vO for RL2.
2. Buck-Boost converter
2.1. Waveforms
Exploration
Supply the circuit in Fig.2 with VI=10V and connect a load resistance
RL1=200. You will do this by disconnecting all the jumpers and
connecting J1 with J2, J5 with J6, J8 with J9, J10 with J11 and R3
closed.
M 2
D 3
IR F 9 1 3 0
1
L2
M BR 040
C 2
1m
220u
V in
10Vdc
V1 = 0
V2 = 10
TD = 0
TR = 1n
TF = 1n
PW = 25u
PER = 50u
Vcm d
R L
200
R 6
Fig.2. Buck-Boost converter
R 7
On the ground terminal of the control transistor M 2, apply a
rectangular signal vcmd from the function generator, with an amplitude
of 10V, frequency 20KHz and a duty cycle =50%.
Visualize the waveforms of the following signals:
o the control voltage vcmd (t) and the voltage on R6, vR6(t),
between J13 and GND (R6 acts like a current transducer for
iL2(t));
o the control voltage vcmd (t) and the voltage on R7, vR7(t)
between J14 and GND (R7 acts like a current transducer for
iC2(t));
o the control voltage vcmd (t) and the output voltage vO(t). The
output voltage is measured between OUT and GND, for J14
connected to the ground.
Results
Draw the waveforms for vcmd (t), vO(t), vL2(t), iRL(t), iC2(t), iD3(t), iL2(t)
and iI(t).
2.2. Verifying the relationship between the output and the input voltage
Exploration
Visualize the control voltage vcmd(t) and the output voltage vO(t), for
RL1=20 and compute VO/VI.
Modify the value of the input voltage and the amplitude of the control
voltage to 8V. Measure once again the output voltage and recompute
VO/VI.
Results
The value of VO/VI for VI=10V.
The value of VO/VI for VI=8V.
2.3. Variation of the output voltage ripple vO with load resistance
Exploration
For the circuit in Fig.2 with RL1 apply once again vcmd with a duty
cycle =50%. Copy the values for v O and vO you obtained in section
2.2.
At the output, replace the load resistance RL1 with RL2 = 250, by
disconnecting R3 and connecting the jumper on the R4 position.
Visualize the control and the output voltages, measure the output
voltage vO, as well as the variation of the output voltage, vO.
Results
The values of VO and vO for =50% (copied from section 2.2.)
Draw the waveforms for vcmd (t) and vO(t), for RL2.
The values of VO and vO for RL2.
REFERENCES
1. Oltean, G., Circuite Electronice, UT Pres, Cluj-Napoca, 2007, ISBN 978973-662-300-4
2. D. Petreu, . Lungu - Surse n comutaie ndrumtor de laborator, Ed.
Mediamira, Cluj-Napoca, 1999.
3. http://www.bel.utcluj.ro/dce/didactic/fec/fec.htm
Fig. 3. Experimental assembly
