1.-Servo Operado NM10

Technical Information
Proservo NMS5
Intelligent Tank Gauge with High Accuracy Performance
Liquid Level, I/F, Density & Density Profile Application
Proservo NMS5 of intelligent tank gauges is designed for

high accuracy liquid level measurement in storage and
process applications.
It fulfills the exact demands of tank inventory management,
loss control, total cost saving and safe operation.
Features and Benefits
Typical areas of application include:
up to three liquid phases
Oil (fuels)
Profiling of Iiquid density throughout the tank (Tank

profile) and upper layer (I/F profile)
LPG/LNG
Chemicals
Water / chemical interface measurement
Alcohols
Tank mounted intelligence makes the NMS5 ideal for single
or multi-task installation, converting a wide range of
measurement functions including:
Liquid level
Interface level
Spot density
SIL2 Certified
Measures liquid to an accuracy of +/- 0.7 mm
Measures two clear interface levels and specific gravity of
Latest microtechnology keeps the design simple,

lightweight and compact
Wetted parts are completely separated from the
electronic circuit
Tank top mounting with 3 flange weighing only 12kg
(aluminum version)
Wide range of output signals including V1, RS 485,
WM550, M/S, Enraf BPM and HART protocol
Material and pressure rating of the wetted parts can be
selected according to the application.
Density profile
Suitable for atmospheric and high pressure applications

up to 2.45MPa/24.5bar
Tank bottom
Maintenance prediction of the instrument
Water dip
Direct connection of spot or average temperature probes

Easy to program using the E+H matrix system
Robust IP67/NEMA 4X housing
Selectable English, Japanese or Chinese display
Proactive safety diagnostics output to display and System
Operators (patent pending)
TI 00452G/08/EN/05.13
71240040
Software Ver. V.4.27G
Proservo NMS5
Table of Contents
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Liquid Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Degree of Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Function and System Design . . . . . . . . . . . . . . . . . . . . . . . . . 3

Measuring System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Major Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Operating Principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Typical Tank Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Measurement Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Operating Condition: Process . . . . . . . . . . . . . . . . . . . . . . . 23

Process Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Measuring Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Application Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Displacer Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Displacer Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Recommended Displacer by Application . . . . . . . . . . . . . . . . . . . 8
Point to Confirm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Custody Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Material Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Process Connection Size: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Mechanical Construction . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Design and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Housing Materials of Construction . . . . . . . . . . . . . . . . . . . . . . 24
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Flange Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Measuring Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Displacer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cable Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Input for Local Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Human Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating Concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Display (LCD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Memo Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Output Parameters based on Communication Protocol . . . . . . .10
RS485 Modbus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Bidirectional Serial Pulse (V1 Protocol). . . . . . . . . . . . . . . . . . . 11
HART Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Whessoematic 550 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Mark/Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Enraf Bi Phase Mark (BPM) . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Analogue Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Auxiliary Energy/Electrical for Primary Output . . . . . . . . . 15
V1 Serial Pulse Modbus RS 485 HART Enraf BPM . . . . . . . . . . .15
Whessoematic 550 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Mark/Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Cable Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Safe Electrical Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 19
Maximum Measured Error . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Operating Conditions: Environment . . . . . . . . . . . . . . . . . . 20
Modbus (RS485 Output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sakura V1 Serial Pulse Ouput . . . . . . . . . . . . . . . . . . . . . . . . . .20
Enraf Bi Phase Mark Output . . . . . . . . . . . . . . . . . . . . . . . . . . 21
HART Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Whessoematic 550 (WM 550) Output . . . . . . . . . . . . . . . . . . .21
Varec Mark Space (M/S) Output . . . . . . . . . . . . . . . . . . . . . . . 22
Ambient Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Advanced Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance Prediction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Proactive Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
27
27
27
Certificates and Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Ex Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Custody Transfer Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Overspill Prevention . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
SIL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
External Standards and Guidelines . . . . . . . . . . . . . . . . . . . . . . 28
Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
NMS5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Calibration Chamber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power+Control Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ball Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reducing Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
32
32
34
35
37
Supplementary Documentation. . . . . . . . . . . . . . . . . . . . . .
Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compact Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional Safety Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
38
38
38
38
38
38
Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Stainless Steel Conversion Table . . . . . . . . . . . . . . . . . . . . . . . 39
Endress+Hauser
Proservo NMS5
Function and System Design

Measuring System
NMS5 is an intelligent tank gauge for measuring liquid levels with high precision, and employing the latest
microprocessor technology. In addition to gauging level, NMS5 can measure the interfaces between up to three
liquids, specific gravity of each and discern tank bottom. To enable accurate volume calculation or simple indication, NMS5 will accept input from either an average temperature probe NMT 53x series (via twisted pair
cables, HART protocol) or spot temperature element (via 3 wire Pt. 100 RTD signal). Once installed, all calibration and operating functions can be done via the user friendly Matrix program and touch sensitive keypad.
Tank side monitoring and operation can be performed by the Promonitor NRF 560.
Power (AC / DC)

Output
NMT539
NMS5
HART
Temp.
Level
Interface
Density
Water Dip
Bottom
NRF560
Power
(AC / DC)
Power (AC / DC)
HART
Power (AC / DC)
HART
to HOST System
in Control Room
Figure 1:
Endress+Hauser
Measuring System
Proservo NMS5
System Configuration
From single tank level measurement to the largest oil refinery applications, NMS5 can be an integral part of
tank farm management solutions. A wide variety of data output protocols are available for seamless
integration into many commonly used systems.
A primary example is Endress+Hausers revolutionary Tankvision., A scalable concept, offering local tank
management for up to 225 tanks via Modbus, V1 or Whessomatic 550 protocols. Accumulated data is
available to DCS and other plant management systems via a Host Link.
Output protocols
Modbus, RS485 or current loop
V1 serial pulse
Whessomatic 550
local HART
Mark/Space
Enraf BPM
Modbus
SCADA
DCS/PLC
Host Link
$EVICE#ONlG
LAN
TCP/IP
Data Concentrator
Data Scanner
Data Scanner
(Field Protcol)
V1, Modbus
HART
Figure 2:
Major Application
HART
HART
NMS5 system configuration Serial pulse output
The number of measuring functions and output options as well as the lightweight compact design enables
NMS5 to be installed in a wide range of applications at minimal cost.
Petroleum Industry
From oil production to storage at an oil depot, there exists an extensive need to measure and manage a wide
variety of products. Remote tank gauging and an inventory management system combined into NMS5 and a
receiving computer is an ideal way to measure and manage tank contents.
Chemical Industry
A wide choice of products are available in the wetted parts construction manufacturing industry, to ensure
chemical compatibility and long life.
Power Plant
Fuel oil levels are a major applications where precise measurement is required to ensure safe operation.
Endress+Hauser
Proservo NMS5
Operating Principle
NMS5 tank gauging system is based on the principle of gauging displacement.

A small displacer is accurately positioned in a liquid medium using a servo motor. The displacer is then
suspended on a measuring wire which is wound onto a finely grooved drum housing. NMS5 counts the rotation of the wire drum and calculates the traveling distance of the wire and then obtain the liquid level change.
The drum is driven via coupling magnets which are completely separated by the drum housing. Outer magnets
are connected to the wire drum whilst inner magnets are connected to the drive motor. As the inner magnets
turn, their magnetic attraction causes the outer magnets to turn, as well, causing the entire drum assembly to
turn. The weight of the displacer on the wire creates torque on the outer magnets generating change of
magnetic flux. These changes generated in the drum assembly are detected by a unique electromagnetic
transducer on the inner magnets. The drive motor is actuated to balance the voltage generated by variations of
magnetic flux to equal the reference voltage defined by operating commands.
When the displacer is lowered and touches a liquid, the weight of the displacer is reduced by liquid buoyancy
force. As a result, torque in the magnetic coupling changes, which is measured by 5 sets of Hall sensors,
(patented) chips which are temperature compensated. A signal, indicating the position of the displacer, is sent
to the motor control circuit. As the liquid levels rise and fall, the displacer position is adjusted by the drive
motor. The rotation of the wire drum is precisely evaluated to determine level value.
Outside Magnet
Wire Drum
Inside Magnet
Weight
Signal
Hall Element
Weight Data
Measurement
Wire
Displacer
Position
Data
CPU
Motor Drive Signal

Encoder
Motor
Displacer
Figure 3:
Endress+Hauser
Direct Torque Detection
Proservo NMS5
Typical Tank Installation
Fixed Roof Tank with Stilling Well
High Pressure Tank with Stilling Well and Ball Valve

NMS5
NMS5
E
E-+
NMT539
NMT539
Ball Valve
Reducer
Measuring Wire
Measuring Wire
Displacer
Displacer
Stilling Well
Figure 4:
Stilling Well
Fixed Roof Tank (Left) / High Pressure Tank (Right)
Floating Roof Tank and/or

Covered Floating Roof Tank
Note!
When NMS5 is installed in the floating roof tank,
ensure to use a stilling well.
NMS5
E
NMS5
+
E
NMT
Measuring Wire
Measuring Wire
Displacer
Displacer
Stilling Well
Figure 5:
Floating Roof Tank
Endress+Hauser
Proservo NMS5
Measurement Terminology
Level
Upper
Density
Upper I/F
Middle
Density
Middle I/F
Lower
Density
Tank Bottom
Figure 6:
NMS5 with standard level, I/F x 2, Tank bottom and spot density x 3 measurement
I/ F Projle
True Average Density
within Upper Layer
Tank Projle
True Average Density
throughout Tank
Level
Density Measured Point

(2 to 16 points selectable)
between Level to Upper I/F
Density Measured Point

(2 to 16 points selectable)
throughout Liquid
Oil
Upper I/F
Emulsion
Water
Figure 7:
Endress+Hauser
Tank Floor
Density Profile measurement "I/F (Interface) Profile" (Left) "Tank Profile" Measurement Range (Right)
Proservo NMS5
Application Selection
Displacer Selection Guide
A wide variety of displacers are available to meet your applications. Proper displacer selection ensures optimal
performance and longevity. The following guidelines will assist you in selecting the ideal displacer for your
application.
Displacer Types
30mm
40mm
50mm
70mm
110mm
(Standard materials available)

316
Alloy C
PTFE
Recommended Displacer by
Application
Application
Surface
Interface
Density
Viscous
50mm PTFE
Not
Recommended
Not
Recommended
Crude
50mm 316
50mm PTFE
50mm 316
50mm PTFE
50mm 316
50mm PTFE
Black oil
50mm 316
50mm 316
50mm 316
White oil
50mm 316
50mm 316
50mm 316
Liquefied gases, LPG/LNG
70mm 316
70mm 316
50mm 316
50mm Alloy C
50mm PTFE
50mm Alloy C
50mm PTFE
50mm Alloy C
50mm PTFE
70mm 316
110mm 316
N/A
N/A
Aggressive
Custody Transfer
Note!
The above table is for 80A (3") mounting flange or larger.
Endress+Hauser
Proservo NMS5
Point to Confirm
Application:
What will be the primary measurement function in your application? Most applications can be generalized into
three classifications: level data, density data, or both. NMS5 is primarily a highly accurate level measurement
gauging instrument, with the added ability to measure density. Level is derived by determining fluid surface
level, interface level(s) between different liquids, as well as finding tank floor or datum plate. Density served
from single-point (called spot measurements), as well as profile measurements of all liquid(s) in a tank.
Surface Level:
In general, larger diameter displacers have better accuracy under similar conditions.
Interface Level(s):
Cylindrical-shaped displacers, with rounded top and bottom, reduce resistance while moving through liquid(s).
Thus, providing smoother movement and faster interface measurements, compared to flat-based displacers,
particularly in density profile measurements that span the full tank height. Note that, in order for a displacer
to travel down through liquid(s), displacer density (its weight divided by its volume) must be higher than liquid(s) density.
Tank-bottom/Datum Plate Level:
(same as for Interface Levels)
Density:
Since the density is the calculated result of two of more measurements, a displacer with higher volume will
usually yield the most accurate density measurement. In most cases we recommend our 50mm diameter
displacer for density measurement.
Level and Density:
When an application calls for equal importance placed on measuring both level and density, the 50mm
diameter, cylindrical displacer will give the best all-around performance.
Custody Transfer
What is the requirement for Custody Transfer approval?

The 70mm, conical, 316 displacer is the choice for requirements per NMi
The 110mm, conical 316 displacer is the choice for requirements per PTB
Material Compatibility
What are the liquid(s) characteristics of your application? Displacers are available in three different standard
materials. Material compatibility should be confirmed to ensure safe operation and optimal NMS5
performance.
316:
Stainless steel is a highly versatile industrial material and provides good compatibility with a wide range of
chemicals, including most white and black oils.
Alloy C:
This high-performance material is harder than 316, and provides excellent resistance to many of harshest
corrosive chemical applications.
PTFE:
One of the most well-known and versatile polymer materials, this high-performance material has one of the
lowest friction coefficients. It provides excellent performance in viscous/sticky liquids, and also has excellent
chemical resistance to a wide range of corrosives
Process Connection Size
Endress+Hauser
The process connection defines the tank process entry, and may affect displacer size. The standard NMS5
process connections start at 3/DN80 and fit most tank gauging applications. Accordingly, most applications
can be covered with one of the 50mm or 70mm displacer options. Smaller diameter displacers are available
when the process connection is smaller. Note that, when the 110mm diameter custody transfer approval (PTB)
displacer is selected, a separate calibration and maintenance chamber is recommended between the NMS5 and
tank process connection.
Proservo NMS5
Input
Input for Local Devices
Signal
Multi drop local HART protocol max. 4 devices
Power supply
DC 24V
Additional units
NMT 53x average temperature sensor

NRF 560 field data processor
Other - compatible HART devices
Spot temperature Pt 100 Ohm ISO standard three wire connection
Output
Output Parameters based on
Communication Protocol
V1(new)
V1 (old)
MODBUS
HART
WM550
ENRAF
M/S
Level
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Temperature (Product)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Vapor Temperature
Yes
Yes
Yes
Yes
Upper I/F (Water Level) *1
Yes
Yes
Yes
Yes
Yes
Middle I/F
Yes
Yes
Yes
Upper Density *2
Yes
Yes
Yes
Yes
Middle Densuty*3
Yes
Yes
Yes
Lower Density*4
Yes
Yes
Yes
Average Density *5
Yes
Yes
Yes
1-16 points Individual Density *6
Yes
Yes
Multi-Element Temperature
Yes
Yes
Yes
Yes
--
HART device input (Device 1)
Yes
Yes
Yes
Yes
HART device input (Device 2)
Yes
Yes
Yes
Yes
Alarm data
Yes
Yes
Yes
Yes
Yes
Yes
KA0002N
KA001N
Protocol Documentation
Note!
Upper I/F output value can be either selected from the Proservos own displacer measurement or Water
Bottom measured value via the Prothermo NMT 539.
A single point density measurement within the upper layer liquid in the tank. The measurement position is
configured to 150mm below the liquid surface at default.
A single point density measurement within the middle layer liquid in the tank. The measurement position is
configured to 150mm below the upper interface level at default.
A single point density measurement within the lower layer liquid in the tank. The measurement position is
configured to 150mm below the middle interface at default
The value of this Average Density is based on the calculation after performing the Density Profile operation
at the Proservo.
All of the selected number of density measured value from 1 ~ 16 points can be transmitted.
10
Endress+Hauser
Proservo NMS5
RS485 Modbus
Module name
Commdule RS 485 communication module (~2008),

COM - 5 (2009~)
No. of unit
Maximum 10 instruments per loop
Baud rate
600/1,200/ 2,400/ 4,800/ 9,600/ 19,200 bit/s, selectable
Parity
Odd, Even, None, selectable
Cable
Two wire twisted cable with screening (DGND is connected to the

ground cable)
Topology
Serial bus, electrically isolated, tree structure
Transmission distance
Maximum 1,200 m including limbs or branches (negligible with

branches under 3 m)
Instrument address
Accessed via touch control
Isolation
Bus inputs are electrically isolated from the other electronics
Module name
COM - 1
No. of units
Baud rate
3,300 BPS
Cable
Two wire (twisted pair) unscreened cable
Topology
Serial bus, tree structure
Maximum 6,000 m
Instrument address
Isolation
Serial communication circuit isolated from other circuits
Module name
Commdule HART (2009), COM - 6 (2009~)
No. of units
Baud rate
1,200 BPS
Cable
Two wire, twisted pair screened cable Minimum core 0.15

(24AWG)
Maximum 1,200 m
Instrument address
Isolation
Bus input are electrically isolated from the other electronics
Bidirectional Serial Pulse

(V1 Protocol)
HART Protocol
Endress+Hauser
11
Proservo NMS5
Whessoematic 550
Module name
WM550 communication module
No. of units
15 instruments per loop (connected to RTU)
Baud rate
1,200 / 2,400 bit/s
Cable
Two wire, twisted cable with screening
Topology
20 mA current loop
Depending on specifications (ask your E+H engineer)
Instrument address
Setting by DIP switches on communication board
Isolation
Current loop circuit isolated from other circuits
Module name
Mark/Space communication module
No. of units
Depending on specification (ask to your E+H engineer)
Baud rate
1,200 / 2,400 / 4,800 / 9,600 / 19,200 bit/s
Cable
Four wire
Topology
Serial bus, tree structure
Depending on specifications (ask your E+H engineer)
Instrument address
Setting by DIP switches on communication board
Isolation
Serial pulse isolated from other circuits
Module name
COM - 3
No. of units
Baud rate
1,200, 2,400 bit/s, selectable
Cable
Two wire, twisted cable with screening
Topology
Serial bus, electrically isolated, tree structure
Maximum 10 km
Instrument address
Isolation
Serial communication circuit isolated from other circuits
Mark/Space
Enraf Bi Phase Mark (BPM)
12
Endress+Hauser
Proservo NMS5
Analogue Output
Module name
I/O - 5
Output
4 to 20 mA, active, two channels freely assignable value
On alarm
Switchable Max. 22mA, Min. 2mA or hold last measured value
Electrical isolation
Analogue output isolated from other circuits
Maximum load
500 ohm
Load effect
Negligible
Module name
I/O - 3
Alarm output, Standard

(Order Code position
050= 1,2,3 or 5)
4 relays with potential-free change-over contacts, freely assignable to

measured value
Hysteresis, Alarm output
Switch points and switching hysteresis freely adjustable, residual

current fail-safe mode: minimum or maximum, selectable
Relay
Operation output logic

Relay Condition
Initial Configuration
(Normal Status)
Open
Closed
On Alarm
Closed
Open
On Device Error
Closed
Open
On Abnormal Power Supply

(5% lower than, or 5%
higher than specified power
supply)
Custody
Transfer
Closed
Custody
Transfer
Open
Power Outage
Switching capacity, Alarm output
Endress+Hauser
Hold Last Condition
Max. 250VAC, 2A/62.5W

Max. 220VDC, 2A/60W
FM/CSA: 30VAC, 2A/42VDC, 2A, 60W
13
Proservo NMS5
Alarm output ,
Overspill prevention
(Order Code position 050=4)
2 relays with potential- free changeover contacts, assignable to Level
Hysteresis, Alarm output
Switch points and switching hysteresis freely adjustable, residual

current fail-safe mode: minimum or maximum, selectable

Relay Condition
Initial Configuration (Normal Status)
Closed
On Alarm
Open
On Device Error
Open
On Abnormal Power Supply (5%

lower than, or 5% higher than specified power supply)
Open
Power Outage
Open
Switching capacity
Umax. 200VDC/200VppAC
Imax. 0.5AC, DC or peak AC
Pmax. 15W
Operation Input
2 photocouplers, for external input from controller (tumbler switch,

DCS, etc.)

Gauge Status
14
CTR1
CTR2
LEVEL
0 (OFF)
0 (OFF)
UP
1 (ON)
0 (OFF)
STOP
0 (OFF)
1 (ON)
INTERFACE LVEL
1 (ON)
1 (ON)
Input voltage
15VDC, active circuit (supplied by NMS5)
Input current
Approximately 5mA
Endress+Hauser
Proservo NMS5
Auxiliary Energy
Electrical for Primary Output
V1 Serial Pulse
Modbus RS 485
HART Enraf BPM
L
L
N
Power Supply
AC 85...264V 50/60Hz
or
DC 20...62V
AC 20...55V
Alarm Contact
Alarm Contact
4 ... 20mA
Channel 2
Port_A +
Local HART
Port_A (see Caution!.)
G
Alarm Contact
0TSPOTTEMP
Port_B +
Non IS HART to NRF or others
Port_B Digital Output
RS485,
V1 Serial Pulse
or Remote HART
Alarm Contact
Ex d local (slave) HART:
Terminals 4 & 5
Digital Output:
Terminals 6 & 7
- V1 serial pulse
- Modbus (RS485)
- HART
- Enraf BPM
Operation
Contact
Input
4 ... 20mA
Channel 1
Ex ia local (slave) HART, or
Pt100 3 wire spot RTD (see Caution!.)
Terminals 24 & 25 (26)
4 to 20mA Output:
Terminals 20 & 21, 22 & 23
Note:
Terminals 22 & 23 will be used as Status 1 Input
WHENSIGNALINPUTFROMlELDUNIT/RDERCODEPOSITION IS
4: HART and Status 1 input
5: HART, Pt100 Spot and Status 1 input
6: HART, Pt100 Spot temp., Operation cntact, and Status 1 input
Refer to ordering information.
Caution!
Terminal connection for Whessoe Matic 550 (WM550) and Mark Space, refer to the next few pages.
4ERMINALSANDFOR(!24DEVICESAREINTER CONNECTEDON%XPLOSIONPROOF%XD CERTIlEDVERSION
Terminals 24 & 25 (and 24, 25 & 26 for spot temp.) will be intrinsically safe (i.s.) device connection
ONLYWHENINTRINSICALLYSAFECERTIlEDVERSIONISSELECTED
Figure 8:
Endress+Hauser
Electrical for V1 Serial Pulse, Modbus RS 485, HART Enraf BPM
15
Proservo NMS5
Whessoematic 550
WM550
Channel 2
Ex d Local HART
(see Caution!.)
Local HART to NRF

04
3 wire RTD Stop temp.
WM550
Channel 1
Ex d local (slave) HART or
Ex d local (slave) HART:
Terminals 4 & 5
Whessoe Matic (WM) 550 output:

Terminals 20 &21, 22 & 23
WM550 is the current loop redundant data transmission protocol.
Since these 4 terminals are occupied by WM550 terminal connection,
4 - 20mA output and status 1 input function are no longer available.
Caution!
Figure 9:
16
Electrical for Whessoematic 550
Endress+Hauser
Proservo NMS5
Mark/Space
L
L
N
Mark
Power Supply
AC 85...264V 50/60Hz
or
DC 20...62V
AC 20...55V
Space
Port_A +
Local HART
Port_A (see Caution!.)
G
G
N
Port_B +
Non IS HART to NMT or other
Port_B -
Operation
Contact
Input
04SPOTTEMP
Mark/Space
Exd local (slave) HART:
Ex d local (slave) HART or

Terminals 4 & 5
M/S output:
Terminals 20 &21, 22 & 23
M/S is the serial pulse digital data transmission along with separate
power supply circuit. Since these 4 terminals are occupied by M/S
terminal connection, 4 - 20mA output and status 1 input function
are no longer available.
Caution!
Figure 10: Electrical for Mark / Space
Endress+Hauser
17
Proservo NMS5
Cable Entry
Thread: G , ,
NPT , ,
M20, 25
*TIIS: G only, CSA: NPT only
Supply Voltage
High voltage type: 85 to 264 VAC, 50/60 Hz

Low voltage type: 20 to 62 VDC / 20 to 55 VAC 50/60Hz
Caution!
Allowable voltage supply is specifically stated depending on each Ex approval. Refer to the designated
certification
Power Consumption
Maximum 50 VA, 50W
Safe Electrical Isolation
Between power supply and signal output, CPU, RS 485, relay and other electronics
18
Endress+Hauser
Proservo NMS5
Performance Characteristics
Maximum Measured Error
Level
0.7mm ( 0.027 inch)*1
Interface
2.7 mm ( 0.106 inch)*2
Density
0.005 g/cm3 *3
Sensitivity
0.1 mm ( 0.004 inch)
Motion delay timer
Configurable in 20ms steps from 0 to 9.9 seconds
*1 : Under reference conditions

*2 : Difference of product densities 100kg/m3(6.25 lb)/ft3
*3 : (optional) when calibrated and equipped for density measurement
Compensation
Displacer
Automatic compensation of displacer weight
Tank Wall
Compensation of depression and distortion
Endress+Hauser
19
Proservo NMS5
Operating Conditions: Environment

Bus installation
Modbus (RS485 Output)
Termination Resistors
Set terminators as required in specific enviroments.
Bus Address
Each transmitter has an individual bus address configured in the software of the transmitter.
Bus Cabling
The bus cabling is galvanically isolated from the transmitter and the PC plug-in board or the interface adapter.
The screening must be grounded and have electrical continuity throughout.
Bus Topology
When planning a system, attention should be paid to possible segmentation of the bus according to individual
plant sections. Suitable topologies are:
Tree of total length 1200 m
Sakura V1 Serial Pulse Ouput
The bus is connected to a RTU8, Tankvision or other Endress+Hauser V1- type receiver. The interface or
receiver must be configured accordingly.
It is not necessary to set any termination resistors for serial pulse output.
Bus Address
Each transmitter on a signal loop has an individual bus address. This is defined within the transmitter software.
Bus Cabling
The bus cabling is electrically isolated from the transmitter and from the interface receiver.
Standard communication cable (non-shielded twisted pair cable) can be used for the data transmission.
Bus Topology
The suitable topologies for the serial pulse output are:
Serial max. 6000 m (Sakura V1)
Tree of total length 6000 m. (Sakura V1)
20
Endress+Hauser
Proservo NMS5
Enraf Bi Phase Mark Output
The bus is connected to an Enraf I/F CIU or RTU8 to transmit measured value to upper host system as Entis
(Enraf TG program) or Fuels Manager. These interface must be configured accordingly.
It is not necessary to set any termination resistors for serial pulse output.
Bus Address
Each transmitter on a signal loop has an individual bus address. This is defined within the transmitter software.
Bus Cabling
The bus cabling is electrically isolated from the transmitter and from the interface receiver. Standard
communication cable can be used for the data transmission.
Bus Topology
The suitable topologies for Enraf BPM serial pulse output are:
Serial max. resistance: 400 ohm at 3 bus loops or less (10 transmitters per 1bus loop)
Serial max. capacitance: 1 micro F or less
Data Transmission & Operation
NMS5 is capable to transmit following sensory data as well as gauge operation command via Enraf BPM serial
pulse output.
Data: level, temperature, operation status
Gauge command: STOP, UP, LEVEL, I/F
HART Output
The bus is connected to a HART master. The HART master must be configured accordingly.
Bus Address
Each transmitter on a signal loop has an individual bus address. This is defined within the transmitter software
and / or auxiliary configuration environment such as host system or Field Communicator 375.
Bus Cabling
The screening must be grounded and have electrical continuity throughout. EMC tests indicate the best result
when the grounding at both ends and each transmitter is established. If there is a potential difference in
between the grounds, measurement must be taken to equalize whilst observing a relevant hazardous area.
Bus Topology
The suitable topologies are:
Serial max. 1000 m
Tree of total length 1000 m.
Whessoematic 550 (WM 550)

Output
The bus is normally connected to Whessoe 1098, RTU 8 or other upper host system via dual channel (can be
single) WM550 current loop.
Admissible termination resistance should be calculated as follow.
R = [Va - {n x (Vb + Vc)}] / 0.02
R = terminal resistance in the system
n = number of transmitter in the system
Va = max. available voltage at receiver
Vb = voltage drop across transmitter
Vc = voltage drop across receiver
Endress+Hauser
21
Proservo NMS5
Bus Address
Each transmitter on a signal loop has an individual bus address. This is defined within the transmitter by
mechanical dip switch on com board.
Bus Cabling
BS5308 or equivalent 1.5sq.mm screened twisted pairs are recommended for bus cabling.
Bus Topology
The suitable topologies for the WM550 current output are depending on number of transmitter & cable quality
on the loop. Recommended number of transmitter on single loop shall be less than 15 units to achieve the
maximum performance.
Varec Mark Space
(M/S) Output
The bus is normally connected to Interface Unit (IFU), Data acquisition Processor (DAP), RTU 8 or other upper
host system via 4 wire M/S serial bus link.
Admissible termination resistance should be calculated as follow.
R = (48 - 33) / {60mA + N (2.0mA)}
R = terminal resistance in the system
N = number of transmitter in the system
48 = supply voltage to receiver
33 = minimum M/S board operation voltage
60mA = required current for system operation
2.0mA = required current per transmitter
Bus Address
Each transmitter on a signal loop has an individual bus address. This is defined within the transmitter by
mechanical dip switch on com board.
Bus Cabling
The total length of field wiring shall be determined by calculation of maximum resistance within the system &
required operation current. Once the total length is determined, distance has to be reduced by half because
of current flow in both B+ & B- leads.
Bus Topology
The suitable topologies for the M/S serial pulse output are depending on number of transmitter & cable quality
on the loop.
Ambient Temperature
-20 to +60oC (-4 to 140F)

-40 to +60oC (-40 to 140F) ATEX approval cold temperature version
Storage Temperature
-40 to +60oC (-40 to 140F)
Liquid Temperature
-200 to +200oC (-328 to +392F)
Degree of Protection
IP 67 with closed housing and cable glands of equal protection type... (ATEX/TIIS)
NEMA 4X...(FM/CSA)
22
Endress+Hauser
Proservo NMS5
Operating Condition: Process

Process Pressure
Aluminum Drum Housing
Stainless Drum Housing
0 to 19.8kPa (Low Pressure)
NMS5-1
NMS5-2
0 to 588kPa (Medium Pressure)
NMS5-4
NMS5-5
0 to 2.45MPa (High Pressure)
NMS5-6
Maximum process pressure of JIS 10k/ANSI 300lbs/DIN DN80/JPI 300lbs: 0.98MPa
Measuring Range
Level
28m
Standard Option
36m
Standard Option
47m
Standard Option
Longer ranges available upon request.

Contact Endress+Hauser representatives.
Density
0.430 to 2.000 g/cm3
Endress+Hauser
23
Proservo NMS5
Mechanical Construction
Design and Dimensions
NMS5 - 1/ NMS5 - 4
Max. 39.7mm
Travel Distance of Displacer
34.6mm for 28m Wire (0.15mm)
for 8 Holes Flange
$ISPLACERPOSITIONATTOPOFTANKCENTEROFmANGE
Displacer position at bottom of tank
NMS5 - 2/ NMS5 - 5 / NMS5 - 6
Max. 41.6mm
Travel Distance of Displacer
Electrical Compartment
Terminal Box
Display (LCD)
Cable Entery (A, B, C, D)
Wire Drum Husing
Flange
Measuring Wire
Displacer
Calibration Window
Window Cover
Touch Control
for 8 Holes Flange
$ISPLACER0OSITIONAT4OPOF4ANK#ENTEROF&LANGE
Displacer Position at Bottom of Tank
Figure. 11: Dimensions of NMS5
Housing Materials of
Construction
Electrical compartment : aluminium casting

Drum chamber for NMS 5-1/5-4 : aluminium casting
Drum chamber for NMS 5-2/5-5/5-6 : stainless steel 316 casting
Weight
NMS 5-1/5-4 : 12 kg
NMS 5-2/5-5/5-6 : 27 kg
Flange Type
ANSI, JIS, DIN 3" and 6" (standard) or equivalent. Refer to order code for full selection.
Flange for NMS5-1/5-4: aluminum
Flange for NMS5-2/5-5/5-6: stainless steel 304
Measuring Wire
Material (standard)
Stainless steel 316, 0.15 mm (standard)

AlloyC. 0.2 mm (max. 16 m range)
PFA coated St/St 316L, 0.4 mm (max. 16m range)
Note!
When liquid level in a tank becomes turbulent condition, use a stilling well pipe or a guide wire for installation.
24
Endress+Hauser
Proservo NMS5
Displacer
Diameter: 50 mm (Standard), 30 to 110mm (option)

Material (Standard): Stainless steel 316
Material (optional): AlloyC, PTFE
Traveling speed: 0 to 2500 mm /min to maximum
Measuring Range/Material/
Diametor of Wire
Feature: 070
Horizontal Movement
Distance (mm/m) on
Drum Wire
0-28m; SUS316L, 0.15mm
1.24
0-16m; PFA>SUS316, 0.4mm
1.34
0-16m; Alloy C, 0.2mm
1.57
0-36m; SUS316L, 0.15mm
1.10
0-22m; Alloy C, 0.2mm
1.57
0-47m; SUS316L, 0.15mm
0.88
Cable Entry
Cable Entry A
Cable Entry B
Cable Gland (Exd)
Cable Entry C
Cable Entry D
Figure 12: Cable Entries
Caution!
When ordering TIIS Ex d specification, cable glands are attached with NMS5. Ensure to use the cable glands.
Endress+Hauser
25
Proservo NMS5
Human Interface
Operating Concept
NMS5 is furnished with a four line illuminated liquid crystal display. With the E+H matrix driven operation,
configuration is simple. Using only three keys, all parameters can be selected and modified. For example:
Operation - level; interface; spot & profile density, water dip, & tank bottom
Current output
Relay output
Maintenance prediction
Calibration, etc.
The display can be configured to be displayed in English, Japanese or Chinese. Measurement unit & decimal
point can be also configured within NMS matrix.
Operational Security
The programming information can be protected by software access codes that disable all programmable
parameters or by a hardware switch to prevent changes from remote transmission or the touch control keypad.
A self-diagnosis function checks for any operational failures.
Display (LCD)
IIluminated LCD
Infrared Transmitting
Diaode
Infrared Receiving
Diaode
3 Optical Operating Elements
" Touch Control"
Figure 13: Display (LCD)
Four line 16-digit illuminated display English, Japanese, Chinese selectable

Programming
Three optical keys (touch control) for selection of matrix functions.
Memo Function
Memo of maintenance information.
26
Endress+Hauser
Proservo NMS5
Advanced Maintenance
Maintenance Prediction
NMS 5 will provide advance warning of required maintenance such as replacement of worn wire etc. The
operating life-span of electrical and mechanical parts of the NMS 5 are factory set within the instruments
memory. This information is checked involving with the built-in clock and compared and registered in the
instrument.
Maintenance
The maintenance record can be accessed via the matrix and will provide information of alarm data (e.g. date,
time, alarm type). A memo function allows the user or an E+H Service Engineer to enter maintenance data
manually.
Proactive Safety
Proactive safety diagnostic function warns of mechanical failure, and outputs maximum level value, e.g. 99999
to local display and fieldbus.
Endress+Hauser
27
Proservo NMS5
Certificates and Approval

Ex Approvals
IEC Ex d [ia] IIB T6...T3 Ga/Gb

IEC Ex d IIB T6...T3 Ga/Gb
IEC Ex d IIC T6...T3 Ga/Gb
ATEX II 1/2G Ex d IIB T6...T3
ATEX II 1/2G Ex d [ia] IIB T6...T3
ATEX II 1/2G Ex d IIC T6...T3
FM XP-AIS Cl.I Div.1 Gr.C-D
FM XP Cl. I Div.1 Gr.C-D
CSA Cl. I Div.1 Gr.C-D
CSA Ex d [ia] Cl. I Div.1 Gr.C-D
TIIS Ex d IIB T4
Custody Transfer Approvals
PTB: Germany
NMi: Netherlands
Overspill Prevention
TV: Germany
SIL
TV: Germany
External Standards and

Guidelines
EMC-Directive 89/336/EC
PE-Directive 97/23/EC
EN 10204-3.1B
OIML-R85/1998
OIML-R85/2008
SIL IEC61508, IEC61511
ISO 9001:2008
28
Endress+Hauser
Proservo NMS5
Order Information
NMS5
010
Drum Housing Pressure Rating; Material:

1 0 200mbar/20kPa/2.9psi; Alu
2
0 200mbar/20kPa/2.9psi; stainless ste>
0 5.88bar/588kPa/85.28psi; Alu
0 5.88bar/588kPa/85.28psi; stainless steel
0 24.5bar/2.45MPa/355.34psi; stainless steel

Special version, TSP-no. to be spec.
9
020
030
040
050
NMS5-
Endress+Hauser
Approval:
0 Weather proof, IP 67 NEMA 4X
1 TIIS Ex d IIB T4
5 FM XP Cl. I Div. 1 Gr. C-D
N FM XP-AIS Cl. I Div.1 Gr. C-D
6 CSA Cl. I Div. 1 Gr. C-D
O CSA Ex d[ia] Cl. I Div. 1 Gr. C-D
G ATEX II 1/2G Ex d IIB T6...T3
Q ATEX II 1/2G Ex d IIC T6...T3
S ATEX II 1/2G Ex d IIB T6...T3, -40C
J ATEX II 1/2G Ex d (ia) IIB T6...T3
U ATEX II 1/2G Ex d (ia) IIB T6...T3, -40C
A IEC Ex d ia IIB T6...T3 Ga/Gb
B IEC Ex d IIB T6...T3 Ga/Gb
C IEC Ex d IIC T6...T3 Ga/Gb
D IEC Ex d ia IIB T6...T3 Ga/Gb, -40C
E IEC Ex d IIB T6...T3 Ga/Gb, -40C
9 Special version, TSP-no. to be spec.
Application:
A Liquid Level
B PTB (<1mm) type approval, liquid level
C NMi (<1mm) type approval, liquid level
D Multi measurement, liquid level, I/F level, bottom, density
E PTB (<1mm) type approval, liquid level, I/F level, bottom, density
F NMi (<1mm) type approval, liquid level, I/F level, bottom, density
G Density profile multi measurement, liquid level, I/F level, bottom, density
H PTB (<1mm)type approval, density profile, liquid level, I/F level, bottom, density
J NMi (<1mm) type approval, density profile, liquid level, I/F level, bottom, density
Y Special version, TSP-no. to be spec.
Output 1:
F Not selected
A 2-way 2-wire (V1 protocol)
J 2-way 2-wire (MDP protocol)
B 2-way 2-wire (BBB protocol)
C 2-way 2-wire (MIC, RS232C protocol)
D 2-way 2-wire (MIC protocol)
G HART active
H HART passive
L Whessmatic 550, overvoltage protection
M Mark Space
N Enraf BPM
P Modbus RS 485
Output 2:
0 Not selected
1 4 x relay SPST
2 2 x 4-20mA
3 4 x relay SPST, 2 x 4 - 20mA
4 2 x relay SPST, Overspill prevention TV
5 4 x relay SPST, 1 x 4 - 20mA
Product designation (part 1)
29
Proservo NMS5
060
070
080
090
100
110
Input:
0 HART (NMT5xx, NRF560, pressure transmitter)
1 1 x spot temperature Pt100, HART (NRF560, pressure transmitter)
2 2 x operation contact, HART (NMT5xx, NRF560, pressure transmitter)
3 1x spot temperature Pt100, 2x operation contact, HART (NRF560, pressure transmitter)
4 1 x status, HART (NMT5xx, NRF560, pressure transmitter)
5 1x spot temperature Pt100, 1x status, HART (NRF560, pressure transmitter)
6 1x spot temperature Pt100, 1x status, 2x operation contact, HART
(NRF560, pressure transmitter)
Measuring Range; wire:
C 0 - 28m; SUS316L, 0.15mm
L 0 - 36m; SUS316L, 0.15mm
N 0 - 47m; SUS316L, 0.15mm
H 0 - 16m; PFA>SUS316, 0.4mm
K 0 - 16m; Alloy C, 0.2mm
M 0 - 22m; Alloy C, 0.2mm
Cable entry:
E 4 x thread G1/2
F 4 x thread G3/4
G 4 x thread NPT1/2
H 4 x thread NPT3/4
L 4 x thread M20
M 4 x thread M25
Process connection:
A 10K 80A RF, flange JIS B2220
C 10K 80A FF, flange JIS B2220
U 10K 150A RF, flange JIS B2220
E 20K 80A RF, flange JIS B2220
G 3" 150Ibs RF, flange JIS B2220
J 3" 300lbs RF,flange ANSI B16.5
W 4" 300lbs RF, flange ANSI B16.5
T 6" 150lbs RF, flange ANSI B16.5
L DN80 PN10 B1, flange EN1092-1 (DIN2527 B)
N DN80 PN25 B1, flange EN1092-1 (DIN2527 B)
Q 80A 150lbs RF, flange JPI 7S-15
S 80A 300lbs RF (apply for NMS5-6), flange JPI 7S-15
Power supply:
3 85 - 264 VAC, 50/60 Hz
4 20 - 62 VDC, 20 - 55 VAC, 50/60 Hz
Displacer:
N Cylindrical 30 mm, SUS316
K Cylindrical 40 mm, SUS316
D
W
V
U
T
B
R
S
Y
NMS5-
30
Cylindrical 50 mm, SUS316

Cylindrical 30 mm, PTFE
Cylindrical 50 mm, AIloy C
Conical 50 mm, PTFE
Conical 70 mm, SUS316
Conical 110 mm, SUS316
Product designation (part 2)
Endress+Hauser
Proservo NMS5
120
Endress+Hauser
O-ring; chamber finishing:

0 NBR; not selected
1 Silicon rubber; not selected
5 Silicone rubber; FEP coated
3 PTFE (wire drum FKM); not selected
4 PTFE (Wire drum FKM); FEP coated
6 CR; not selected
2 FKM; not selected
7 FKM; FEP coated
8 FFKM; not selected
A FFKM; FEP coated
130
Options:
A not selected
C Rc3/8 cleaning nozzle
D Rc3/8 gas purging nozzle
E Guide wire installation
G Relief valve
H Relief valve, pressure gauge
J Sunshade
L Rc3/8 gas purging nozzle, sunshade
M Rc3/8 cleaning nozzle, sunshade
N Rc3/8 gas purging nozzle, guide wire installation
P Rc3/8 cleaning nozzle, guide wire installation
Q Guide wire installation, sunshade
R Relief valve, guide wire installation
S Relief valve, pressure gauge, guide wire installation
T Relief valve, sunshade
U Relief valve, pressure gauge, sunshade
NMS5-
Complete product designation
31
Proservo NMS5
Accessories
Calibration Chamber
Calibration Chamber
8 hole
Flange
300
172
Flange
150
Figure 14: Calibration Chamber
Calibration chamber is recommended for use with tank level gauges in order to allow maintenance (removing
displacers), while tank is in service.
Standard chamber is 6" flange, with bolts & packing for NMS connection.
Note!
The dimensions differ depending on material, flange size. Contact Endress+Hauaser for details.
NHC4HP (high pressure version)
10
20
30
40
NHC4HP-
32
Process Connection:
E 20K 150A RF, flange JIS B2220
G 6" 150lbs RF, flange ANSI B16.5
J 6" 300lbs RF, flange ANSI B16.5
L DIN 150 PN10 B1, flange EN1092-1(DIN2527 B)?
N DIN 150 PN25 B1, flange EN1092-1(DIN2527 B)
S 150A 300lbs RF, flange JPI 7S-15
Pipe Material; Flange Material:
2 STPG370; SS400
3 SUS304TP; SUS304
Bolts, Packing:
0 not used
1 SUS304, Valker #6502
Pressure Gauge, Relief Valve:
1 Selected
Endress+Hauser
Proservo NMS5
NHC4LP (low pressure version)

010
020
Process Connection:
G 6" 150lbs RF, flange ANSI B16.5
L DN150 PN10 B1, flange EN1092-1(DIN2527 B)
Pipe Material; Flange Material:
1 AC4AAC4A
3
9
030
NHC4LP-
Endress+Hauser
SUS304TPSUS304
Bolts, Packing:
0 not used
1 SUS304, Valker #6502
33
Proservo NMS5
Power+Control Switch
Power + Control Switch
3PECIlCATIONS
Rated Voltage
AC110/220V
Rated Current
6A/5A
INST
Terminal Box
Iron Casting
Structure
Explosion Proof d3aG5
LIFT
Aluminum Ally Casting
120
Housing
STOP
OFF
.OOF#ERTIlCATE4
Grounding
65
2 - 7
113
Connection Diagram
NHS8
Term.No
NMS
Term.No
Power Supply
2 Power N
Power L
193
4
5
16 COM
17 CRT1
18 CRT2
Handle
Position
Wiring
INST
OFF
LIFT
STOP
INST
STOP
Cable entry
7
LIFT
OFF
Cable Entry
PF (G)1/2
PF (G) 3/4
PF (G)1
h (mm)
17
20
24
B
140
140
145
Figure 15: Power and Control Switch
Power & Control Switches are used for field mounted tank gauges. This provides additional gauge operation
contact switching in order to control gauges operation, such as hoisting up displacer.
NHS8
010
020
NHS8-
34
Approval:
1 Weather proof IP67
2 Flame proof (JIS d3aG5)
Cable entry:
0 2 x thread G3/4
1 2 x thread G1
2 2 x thread NPT3/4
3 2 x thread NPT1
Endress+Hauser
Proservo NMS5
Ball Valve
Body Cap
Ball
Body
Figure 16: Parts Name of Ball Valve
Ball valves are recommended for use with tank level gauges in order to allow such maintenance as removing
displacers, while tank is in service.
Standard ball valve with ANSI flanges. Ball material is SS304, seat material is PTFE.
Note!
The dimensions vary depending on material, flange size. Contact Endress+Hauser for details.
NHV4A (ANSI flanges)
Standard ball valve with ANSI flanges. Ball material is SS304, seat material is PTFE.
10
20
NHV4A-
Endress+Hauser
Process Connection; Body:

C31 3" 150lbs RF; Steel casting flange ANSI B16.5
S31 3" 150lbs RF; SS304 flange ANSI B16.5
Y99 Special version, TSP-no. to be spec.
Ball Type:
A Full bore
B Reduced bore
35
Proservo NMS5
NHV4J (JIS flanges)

For body in mild steel and in SS304, ball material is SS304, ball material is SS304. For body in SS316, ball material is SS316. Seal material is PTFE.
10

C11 10K 80A RF; Steel flange JIS B2220
S11 10K 80A RF; SUS316 flange JIS B2220
S22 20K 150A RF;SUS316 flange JIS B2220
H11 10K 80A RF; SUS304 flange JIS B2220
H22 20K 150A RF;SUS304 flange JIS B2220
Y99 Special version, TSP-no. to be spec.
20
Ball Type:
A Full bore
B Reduced bore
Y special version, TSP-no. to be spec.
NHV4J-
36
Endress+Hauser
Proservo NMS5
Reducing Flange
High Pressure (ANSI Example)
Low Pressure (JPI Example)
Stud Bolt
Stud Bolt
Flange
Flange
Figure 17: Reducing Flange
Use reducing flange when NMS5 connection 80A(30")and mounting nozzle is 150A(6").
NHF4
10
20
NHF4-

A
10K 150A RF, flange JIS B2220
C
10K 150A FF, flange JIS B2220
E
20K 150A RF, flange JIS B2220
G
6" 150lbs RF, flange ANSI B16.5
J
6" 300lbs RF, flange ANSI B16.5
L
DIN 150 PN10 B1, flange EN1092 (DIN2527 B)
N
DIN 150 PN25 B1, flange EN1092 (DIN2527 B)
Q
150A 150lbs RF, flange JPI 7S-15
S
150A 300lbs RF, flange JPI 7S-15F
Y
Flange Material:
0 SS400
1 SUS304
Note!
NHF4 is not required if NMS5 is ordered with "Order Information; Guide Wire Installation (130-E)".
When ordered as NMS5-xxxxxxxxxxxxE with Guide Wire Installation, all the required mounting equipment
is included.
Endress+Hauser
37
Proservo NMS5
Supplementary Documentation
Technical Information
TI00042G
Prothermo NMT 539
TI00462G
Promonitor NRF 560
Operating Manual
BA00401G
Proservo NMS5
Compact Instructions
KA001N
Whessoemtric 550
KA002N
RS485 Modbus
Safety Instructions
XA00578G
Proservo NMS5 - ATEX
XA00582G
Proservo NMS5 - IECEx
Functional Safety Manual
38
SD00337G
Proservo NMS5 - (4-20mA Output, Overspill prevention)
Endress+Hauser
Proservo NMS5
Appendix
Stainless Steel Conversion
Table
The stainless steel material used in products of Endress + Hauser Yamanashi normally have expressions
according to Japanese industrial standards, such as JIS. Each country or region may have different expressions
place to place.
The following conversion table contains the expression of equivalent stainless steel material based on the
chemical composition and mechanical properties.
Country
Standard
Expressions
Japan
JIS
SUS304
SUS304L
SUS316
SUS316L
Germany
DIN 17006
X5 CrNi 18 10
X5 CrNi 18 12
X2 CrNi 18 11
X5 CrNiMo 17 12 2 /
1713 3
X2 CrNiMo 17 13 2
W.N. 17007
1.4301 1.4303
1.4306
1.4401 / 1.4436
1.4404
France
AFNOR
Z 6 CN 18-09
Z 2CN 18-10
Z 6 CND 17-11 / 17 12
Z2 CND 17-12
Italy
UNI
X5 CrNi 1810
X2 CrNi 1911
X5 CrNiMo 1712 /
1713
X2 CrNiMo 1712
U.K.
BSI
304S15 / 304S16
304S11
316S31 / 316S33
316S11
U.S.A.
AISI
304
304 L
316
316L
U.E.
EURONORM
X6 CrNi 1810
X3 CrNi 1810
X6 CrNiMo 17 12 2 /
17 13 3
X3 CrNiMo 17 12 2
Spain
UNE
X6 CrNi 19-10
X2 CrNi 19-10
X6 CrNiMo 17-12-03
X2 CrNiMo 17-1203
Russia
GOST
08KH18N10
06KH18N11
03KH18N11
03KH17N14M2
ISO
11
10
20
19
ASME
S30400
S30403
S31600
S31603
Note!
Since each standard carries its own mechanical and scientific definition, some expressions on the list above may
not have a straight conversion from the Japanese standard. Consult a local authority or legislature to ensure
proper comparison of the applied standard prior to determining specifications.
Endress+Hauser
39
Endress+Hauser Yamanashi Co., Ltd.

862-1 Mitsukunugi Sakaigawa-cho
Fuefuki-shi Yamanashi,
406-0846 Japan
Phone: ++81 55 266 4964
Fax: ++81 55 266 4969
http://www.endress.com
TI 00452G/08/EN/05.13
71240040
FM+XML/DITA 11.0

1.-Servo Operado NM10

Uploaded by

Copyright:

Available Formats

1.-Servo Operado NM10

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1.-Servo Operado NM10

Uploaded by

Copyright:

Available Formats

Technical Information

Proservo NMS5 of intelligent tank gauges is designed for

Features and Benefits

Typical areas of application include:

up to three liquid phases

Profiling of Iiquid density throughout the tank (Tank

Latest microtechnology keeps the design simple,

Suitable for atmospheric and high pressure applications

Maintenance prediction of the instrument

Direct connection of spot or average temperature probes

Function and System Design . . . . . . . . . . . . . . . . . . . . . . . . . 3

Operating Condition: Process . . . . . . . . . . . . . . . . . . . . . . . 23

Certificates and Approval . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Function and System Design

Power (AC / DC)

Power (AC / DC)

Power (AC / DC)

NMS5 system configuration Serial pulse output

NMS5 tank gauging system is based on the principle of gauging displacement.

Motor Drive Signal

Direct Torque Detection

Typical Tank Installation

Fixed Roof Tank with Stilling Well

High Pressure Tank with Stilling Well and Ball Valve

Fixed Roof Tank (Left) / High Pressure Tank (Right)

Floating Roof Tank and/or

Floating Roof Tank

Density Measured Point

Density Measured Point

(Standard materials available)

Liquefied gases, LPG/LNG

What is the requirement for Custody Transfer approval?

Multi drop local HART protocol max. 4 devices

NMT 53x average temperature sensor

Upper I/F (Water Level) *1

1-16 points Individual Density *6

HART device input (Device 1)

HART device input (Device 2)

Commdule RS 485 communication module (~2008),

Maximum 10 instruments per loop

600/1,200/ 2,400/ 4,800/ 9,600/ 19,200 bit/s, selectable

Odd, Even, None, selectable

Two wire twisted cable with screening (DGND is connected to the

Serial bus, electrically isolated, tree structure

Maximum 1,200 m including limbs or branches (negligible with

Accessed via touch control

Bus inputs are electrically isolated from the other electronics

Maximum 10 instruments per loop

Two wire (twisted pair) unscreened cable

Serial bus, tree structure

Accessed via touch control

Serial communication circuit isolated from other circuits

Commdule HART (2009), COM - 6 (2009~)

Maximum 15 instruments per loop

Two wire, twisted pair screened cable Minimum core 0.15

Accessed via touch control

Bus input are electrically isolated from the other electronics

Bidirectional Serial Pulse

WM550 communication module

15 instruments per loop (connected to RTU)