This document provides repair instructions for disassembling and reassembling the Taurus tool series. It outlines the steps to disconnect, unscrew, and remove various parts like the head, jaw housing, rest mandrel container, and pressure pipe screw. Special tools are required for some steps. Reassembly is done in reverse order. Important notes are provided on correctly installing distance cages in the control valve.
This document provides repair instructions for disassembling and reassembling the Taurus tool series. It outlines the steps to disconnect, unscrew, and remove various parts like the head, jaw housing, rest mandrel container, and pressure pipe screw. Special tools are required for some steps. Reassembly is done in reverse order. Important notes are provided on correctly installing distance cages in the control valve.
This document provides repair instructions for disassembling and reassembling the Taurus tool series. It outlines the steps to disconnect, unscrew, and remove various parts like the head, jaw housing, rest mandrel container, and pressure pipe screw. Special tools are required for some steps. Reassembly is done in reverse order. Important notes are provided on correctly installing distance cages in the control valve.
This document provides repair instructions for disassembling and reassembling the Taurus tool series. It outlines the steps to disconnect, unscrew, and remove various parts like the head, jaw housing, rest mandrel container, and pressure pipe screw. Special tools are required for some steps. Reassembly is done in reverse order. Important notes are provided on correctly installing distance cages in the control valve.
Nordendstrae 13-39 D-64546 Mrfelden-Walldorf Telefon +49 6105 / 962-0 Telefax +49 6105 / 962-287 Internet http://www.gesipa.com E-Mail [email protected]
This document shows the chronology of the disassembling of the Taurus tool series, illustrated by corresponding pictures. This operation necessitates the use of special tools which are separately listed. Special procedures which must be followed are described in details and pictured. Reference is also made to the operating instructions booklet as well as to the illustrated parts price list.
Disconnect the tool from the air pressure supply
Unscrew head (24) Unscrew jaw housing (16) Unscrew rest mandrel container (103/104) Unscrew pressure pipe screw (43a,43) with spring washer (49)
Re-install the rest mandrel container (103/104)
1
Pull-off adapters (42) with lock (41) and retaining spring (48) using the rest mandrel container itself
Important: Remove the housing screw from tool bottom. This screw is maintaining the tool bottom in place and prevents its separation from the tool.
Carefully install the main cylinder in a vice.
Unscrew tool bottom (76,77,78) using a wrench for twin holed nuts according to DIN 3116.
Install the tool into the clamping jig ( Special tool P/N 756 0007) Extract the aluminium cylinder(69,70,71)
Extract the air piston (72,73,74) using a plier
Unscrew Alu nut (57) using the special wrench P/N: 756 2005
Carefully remove the complete air cylinder housing (58,59,60) from the aluminium tube Take great care of not damaging O- Ring (56) !
Unscrew the rear screw plug (40) using special wrench P/N 756 2006
Remove the tool head from the clamping jig
Remove the complete grip section
Empty the hydraulic fluid into an adequate container
Push traction rod (25) backwards out of the tool head
Remove reset plunger (36) from the traction rod
Use a 17mm dia. Alu or plastic stamp for removal of the sealing ring holder (32 Plug the stamp into front of tool head and eject carefully the sealing ring holder using a light hammer.
Proceed as follows in case the control valve (see cut A-A in operating instructions)has to be removed from the air cylinder housing (58,59,60): Remove screw (75) using a T20 Torx screw driver
Unscrew the safety valve (90) using an adequate screw driver
Use an adequate tool to push out the control piston (92) and the plug (96,97,98) from the side of the safety valve Push the airzet rod sealings (93) and spacer cage (91) out of the air cylinder housing.
Order of sequence of the different components of the control valve.
Re-installation of the control valve into the tool requires the use of the spezial Mounting tool for airzet ring, P/N 756 2008. Use this tool as follows : 1. Insert introduction help into base body 2. Drop Airzet ring into side slit. 3. Insert stamp from above and carefully push down until you feel the airzet ring engaging into the introduction help. 4. Pull the introduction help down
10
Push the introduction help sideways into the air cylinder housing. Push with your thumb on the base of the introduction help and then pull back with your fingers until Stop. Grease the Airzet-Ring Mount all parts following the drawings shown in the operating instruction booklet or on the spare parts price list. Warning : Important notice: Take good care of correct installation of the distance cage (91) into the control valve of the Taurus 2 and 3 tools. The distance cage carries a slot on one side. Insert the distance cage with the slotted side first in such a way that the slot connects with the nose inside the control valve bore. Installation of the 3 following distance cages is indifferent. The first distance cage is not present in the Taurus 1. Installation of the 3 distance cages is indifferent.
Re-assembling the tool is done in reversed sequence
