Daconti Electrical Risks in Transmission Line - Pipeline

Power Technology
Newsletter Issue 96
October 2004
ELECTRICAL RISKS IN TRANSMISSION LINE PIPELINE SHARED RIGHTS-OF-WAY

Jose R. Daconti
Executive Consultant
[email protected]
Pipeline Induced Disturbances

Metallic pipelines used for fluid transportation (gas, oil, water, etc) are typically
underground, but they may also have above-ground sections. Underground sections are
protected by an external anti-corrosive coating. Above-ground sections are usually
uncoated (just painted against corrosion) and isolated from the underground sections by means of insulating
joints. Both behave like long conductors insulated from the ground.
The pipeline-induced disturbances are basically induced voltages on the pipeline metal. They are caused by
the power line operating voltage and circulating currents. Some of these voltages are induced when the
power line is under normal steady-state operating conditions. Other induced voltages may occur only during
short-circuits on the transmission line.
Overhead power lines as well as underground power lines can induce harmful disturbances on nearby
metallic pipelines.
Coupling Mechanisms
Generically, a physical process of transferring disturbances to a nearby installation requires the existence of a
source of disturbances, a coupling mechanism and a receptor. In the present analysis, the source of
disturbances is the power line, the receptor is the metallic pipeline and the coupling mechanism is the
capacitive, inductive and conductive coupling between power line and pipeline.
The capacitive coupling disturbance is produced by
the electric field of the power line and needs to be
evaluated only for above-ground sections of pipeline
that are electrically isolated from the ground. As
shown in Figure 1, the capacitive coupling functions
as a capacitive voltage divider. Otherwise, there is
no capacitance between the power line and
underground sections of pipeline. Any pipeline-toground connection makes this disturbance
negligible. Usually, the evaluation of this disturbance
is performed only for steady-state operation
condition of the power line, assuming the line
operates at its maximum operational voltage.
Figure 1 Capacitive coupling
Power Technology
October 2004
Figure 2 shows that the inductive coupling disturbance is produced by the magnetic field of the power line and
needs to be evaluated for underground sections of pipeline. It needs to be evaluated for above-ground
sections of pipeline, only if these sections are grounded. This disturbance depends directly on the
transmission line current unbalance. The evaluation of this disturbance is usually performed for steady-state,
as well as short-circuit operational condition of the power line. This disturbance shall be evaluated taking into
account the maximum anticipated levels of steady-state and short-circuit currents.
Figure 2 Inductive coupling

The conductive coupling disturbance is produced by the ground potential rise due to the electrical currents
injected into the ground from the transmission line. It needs to be evaluated for underground sections of
pipeline. It needs to be evaluated for above-ground sections of pipeline, only if these sections are grounded.
The evaluation of this disturbance is performed only for short-circuit condition of the power line. This
disturbance shall be evaluated taking into account the maximum anticipated level of short-circuit current.
It is important to mention that under short-circuit condition the disturbances due to inductive and conductive
coupling occur simultaneously as shown in Figure 3.
Figure 3 Inductive plus conductive coupling
Page 2
Power Technology
October 2004
Potential Risks
Figure 4 Electrical discharge from power line to pipeline

The most basic concern regarding the proximity between a power line and a pipeline is to make sure that the
electrical clearances between the mentioned installations are large enough to avoid electrical discharges from
the former to the latter, as shown in Figure 4. Besides that, the following risks may exist:
Electric shocks to people who may contact the pipeline: This can happen at above-ground sections of
pipeline and above-ground metallic accessories connected to underground sections of pipeline, as
shown in Figure 5. The tolerability of people to electric shocks depends on the shock duration;
Figure 5 Electric shock
Page 3
Power Technology
October 2004
Damage to the pipeline insulating coating: This can happen at underground sections of pipeline, as a
consequence of the application of an excessive voltage stress across the pipeline coating. The
coating becomes internally exposed to the pipeline metal electric potential Vp (produced by inductive
plus conductive couplings) while becoming externally exposed to the local ground electric potential Vs
(produced by conductive coupling), as shown in Figure 6;
Vs
Vp
Figure 6 Electrical stress applied to pipeline coating
Damage to the pipeline insulating joints: This can happen to insulating joints used to separate aboveground from underground sections of pipeline, or insulating joints used to separate pipeline sections
connected to different cathodic protection systems. These insulating joints can be damaged if
exposed to voltage stresses above their maximum voltage withstand capability, as shown in Figure 7;
VP(L)
VP(R)
Figure 7 Electrical stress applied to insulating joint
Page 4
Power Technology
October 2004
Damage to the pipeline cathodic protection system: This can happen if the pipeline electric potential
(at the point of connection to the cathodic protection system) is above the maximum reverse tolerable
voltage of the cathodic protection system rectifier. See Figure 8.
Figure 8 Electrical stress applied to rectifier
Safety Criteria
People who may contact the pipeline can be exposed to electric shocks (touch voltages) caused by longduration pipeline induced voltages (produced during the steady-state operation of the power line) or shortduration pipeline induced voltages (produced during short-circuit occurrences on the power line). Typically,
long duration shocks should be limited to 5 mA (estimated shock current that would produce loss of muscular
control for 0.5% of children) while short duration shocks should be limited to 164 mA (estimated minimum
shock current that would produce a ventricular fibrillation probability equal to or less than 0.5% for a 50 kg
weight person, according to Dalziels Equation for a shock duration time equal to 0.5 seconds). Although
these are typical limits, each country or state has its own regulation which must be respected. For instance,
New York State Pipeline Code requires that long duration voltages induced on pipelines by electric lines must
be limited to 15 volts.
Damage to the pipeline insulating (anti-corrosive) coating could lead to pipeline corrosion problems. This risk
can be avoided if short-duration voltages applied across the pipeline external coating are limited to 5 kVrms.
Such a level has been considered appropriate for the regularly used thicknesses of plastic (polyethylene) and
bituminous (coal-tar) coatings. Plastic coatings have high thermal stability whereas bituminous coatings have
low thermal stability.
Damage to the pipeline insulating joints can be avoided if the voltage stresses across them are limited to a
level below the maximum withstand voltage of the mentioned joints. The maximum withstand voltage depends
on the type of insulating joint. Some of them are able to withstand 5 kV when submitted to short-duration
voltage stresses. If higher voltage stresses are anticipated, surge arresters should be installed across the
insulating joints. In this case the nominal voltage and the energy dissipation capability of the surge arrester
need to be appropriately specified.
Damage to the pipeline cathodic protection system (CPS) can be avoided by limiting the pipeline induced
electric potential at the point of connection to the CPS to a voltage level that is smaller than the maximum
reverse tolerable voltage of the CPS rectifier, which varies with the type of rectifier. If higher voltage stresses
are anticipated, surge arresters should be installed. This analysis is usually done for the worst condition that
typically occurs during short-duration disturbances.
Page 5

Daconti Electrical Risks in Transmission Line - Pipeline

Uploaded by

Copyright:

Available Formats

Daconti Electrical Risks in Transmission Line - Pipeline

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Daconti Electrical Risks in Transmission Line - Pipeline

Uploaded by

Copyright:

Available Formats

Power Technology

ELECTRICAL RISKS IN TRANSMISSION LINE PIPELINE SHARED RIGHTS-OF-WAY

Pipeline Induced Disturbances

Figure 1 Capacitive coupling

Figure 2 Inductive coupling

Figure 3 Inductive plus conductive coupling

Figure 4 Electrical discharge from power line to pipeline

Figure 5 Electric shock

Figure 7 Electrical stress applied to insulating joint

Figure 8 Electrical stress applied to rectifier

You might also like