Apv - Evaporator Handbook

APV Evaporator Hndbook
12/6/00 11:07 AM Page 2
Introduction ...................................................3
Evaporators...................................................4
Evaporator Type Selection ............................20
Configurations For Energy Conservation .......24
Residence Time In Film Evaporation ..............28
Designing For Energy Efficiency....................32
Physical Properties .......................................34
Mechanical Vapor
Recompression Evaporators..........................36
Evaporators For Industrial And
Chemical Applications .................................42
Waste Water Evaporators ............................47
Tubular Evaporators
For Sanitary Standards ................................50
Evaporator Control ......................................52
Preassembled Evaporators............................54
The Production Of
High Quality Juice Concentrates ...................55
Engineering Conversions ..............................60
Properties Of Saturated
Steam Temperature Tables ............................61
12/6/00 11:07 AM Page 3
As one of the most energy intensive processes used in the dairy, food and
chemical industries, it is essential that evaporation be approached from the
viewpoint of economical energy utilization as well as process effectiveness. This
can be done only if the equipment manufacturer is able to offer a full selection of
evaporation technology and systems developed to accommodate various product
characteristics, the percent of concentration required, and regional energy costs.
This Handbook describes the many types of evaporators and operating options
available through the experience and manufacturing capabilities of companies
within the APV Group.
12/6/00 11:07 AM Page 4
TYPES AND DESIGN

In the evaporation process, concentration of a product is accomplished by boiling
out a solvent, generally water. The recovered end product should have an
optimum solids content consistent with desired product quality and operating
economics. It is a unit operation that is used extensively in processing foods,
chemicals, pharmaceuticals, fruit juices, dairy products, paper and pulp, and both
malt and grain beverages. Also it is a unit operation which, with the possible
exception of distillation, is the most energy intensive.
While the design criteria for evaporators are the same regardless of the industry
involved, two questions always exist: is this equipment best suited for the duty, and
is the equipment arranged for the most efficient and economical use? As a result,
many types of evaporators and many variations in processing techniques have
been developed to take into account different product characteristics and
operating parameters.
TYPES OF EVAPORATORS
The more common types of evaporators include:
Batch pan
Forced circulation
Natural circulation
Wiped film
Rising film tubular
Falling film tubular
Plate equivalents of
tubular evaporators
Rising/falling film tubular
12/6/00 11:07 AM Page 5
BATCH PAN
Next to natural solar evaporation, the batch pan (Figure 1) is one of the oldest
methods of concentration. It is somewhat outdated in today's technology, but is still
used in a few limited applications, such as the concentration of jams and jellies
where whole fruit is present and in processing some pharmaceutical products.
Up until the early 1960's, batch pan also enjoyed wide use in the concentration
of corn syrups.
With a batch pan evaporator, product residence time normally is many hours.
Therefore, it is essential to boil at low temperatures and high vacuum when a
heat sensitive or thermodegradable product is involved. The batch pan is either
jacketed or has internal coils or heaters. Heat transfer areas normally are quite
small due to vessel shapes, and heat transfer coefficients (HTCs) tend to be low
under natural convection conditions. Low surface areas together with low HTC's
generally limit the evaporation capacity of such a system. Heat transfer is
improved by agitation within the vessel. In many cases, large temperature
differences cannot be used for fear of rapid fouling of the heat transfer surface.
Relatively low evaporation capacities, therefore, limit its use.
Figure 1
CONDENSER
STEAM
PRODUCT
CONDENSATE
12/6/00 11:07 AM Page 6
A
R
R
A
NATURAL CIRCULATION
TO CONDENSER
OR VACUUM
Evaporation by natural circulation is

achieved through the use of a
STEAM
short tube bundle within the
PRODUCT
OUT
batch pan or by having an external
shell and tube heater outside of the
main vessel (Figure 2).
FEED
The external heater has the advantage
that its size is not dependent upon the
size or shape of the vessel itself. As a
result, larger evaporation capacities
Figure 2
may be obtained. The most common
application for this type of unit is as a reboiler at the base of a distillation column.
RISING FILM TUBULAR

Considered to be the first 'modern' evaporator used in the industry, the rising film
unit dates back to the early 1900's. The rising film principle was developed
commercially by using a vertical tube with steam condensing on its outside surface
(Figure 3). Liquid on the inside of the tube is brought to a boil, with the vapor
generated forming a core in the center of the tube. As the fluid moves up the tube,
more vapor is formed resulting in a higher central core velocity that forces the
remaining liquid to the tube wall. Higher vapor velocities, in turn, result in thinner
and more rapidly moving liquid film. This provides
TO CONDENSER
OR VACUUM
higher HTC's and shorter product residence time.
The development of the rising
film principle was a giant
STEAM
step forward in the
evaporation field,
particularly in product quality.
In addition, higher HTC's
resulted in reduced heat
transfer area requirements
and consequently, in a lower
FEED
initial capital investment.
6
PRODUCT
OUT
CONDENSATE
Figure 3
12/6/00 11:07 AM Page 7
FALLING FILM TUBULAR

Following development of the rising film principle, it took almost half a century for
a falling film evaporation technique to be perfected (Figure 4). The main problem
was how to design an adequate system for the even distribution of liquid to each
of the tubes. For the rising film evaporator, distribution was easy since the bottom
bonnet of the calandria was always pumped full of liquid, thus allowing equal
flow to each tube.
While each manufacturer has its own technique, falling film distribution generally is
based around use of a perforated plate positioned above the top tube plate of the
calandria. Spreading of liquid to each tube is sometimes further enhanced by
generating flash vapor at this point. The falling film evaporator does have the
advantage that the film is 'going with gravity' instead of against it. This results in
a thinner, faster moving film and gives rise to an even shorter product contact time
and a further improvement in the value of HTC.
To establish a well-developed film, the rising film unit requires a driving film force,
typically a temperature difference of at least 25F (14C) across the heating
surface. In contrast, the falling film evaporator does not have a driving force
limitationpermitting a greater number of evaporator effects to be used within the
same overall operating limits. For
Figure 4
example, if steam is available at

220F (104C), then the last effect
boiling temperature is 120F
STEAM
(49C); the total available

T is equal to 100F (55C).
In this scenario a rising film
evaporator would be limited
to four effects, each with a T
FEED
STEAM
of 25F (14C). However,

using the falling film
technique, it is feasible to have
VACUUM
CONDENSATE
as many as 10 or more effects.
PRODUCT
OUT
12/6/00 11:07 AM Page 8
RISING/FALLING FILM TUBULAR

The rising/falling film evaporator
Figure 5
(Figure 5) has the advantages

of the ease of liquid distribution
of the rising film unit coupled
with lower head room
requirements. The tube bundle
STEAM
is approximately half the height

of either a rising or falling film
evaporator, and the
vapor/liquid separator is
STEAM
VACUUM
positioned at the bottom of

the calandria.
FORCED CIRCULATION
FEED
PRODUCT
OUT
The forced circulation evaporator (Figure 6) was developed for processing liquors
which are susceptible to scaling or crystallizing. Liquid is circulated at a high rate
through the heat exchanger, boiling being prevented within the unit by virtue of a
hydrostatic head maintained above the top tube plate. As the liquid enters the
separator where the absolute pressure is slightly less than in the tube bundle, the
liquid flashes to form a vapor.
The main applications for a forced circulation evaporator are in the concentration
of inversely soluble materials, crystallizing duties, and in the concentration of
thermally degradable materials which result in the deposition of solids. In all cases,
the temperature rise across the tube bundle is kept as low as possible, often as
low as 3-5F (2-3C). This results in a recirculation ratio as high as 220 to 330
lbs (100 to 150 Kg) of liquor per pound (kilogram) of water evaporated. These
high recirculation rates result in high liquor velocities through the tube which help
to minimize the build up of deposits or crystals along the heating surface. Forced
circulation evaporators normally are more expensive than film evaporators
because of the need for large bore circulating pipework and large recirculating
pumps. Operating costs of such a unit also are considerably higher.
8
12/6/00 11:07 AM Page 9
Figure 6
SEPARATOR
LIQUOR HEAD
TO PREVENT BOILING
AT HEATING SURFACE
LOW TEMPERATURE
RISE ACROSS
CALANDRIA
VAPOR
OUTLET
CONCENTRATED
LIQUOR
OUTLET
CALANDRIA
DILUTE
LIQUOR
INLET
CIRCULATION PUMP GIVING

HIGH LIQUOR VELOCITIES
OVER HEATING SURFACE
WIPED FILM
The wiped or agitated thin film evaporator has limited applications due to the high
cost and is confined mainly to the concentration of very viscous materials and the
stripping of solvents down to very low levels. Feed is introduced at the top of the
evaporator and is spread by wiper blades on to the vertical cylindrical surface
inside the unit. Evaporation of the solvent takes place as the thin film moves down
the evaporator wall. The heating medium normally is high pressure steam or oil.
A high temperature heating medium generally is necessary to obtain a reasonable
evaporation rate since the heat transfer surface available is relatively small as a
direct result of its cylindrical configuration.
The wiped film evaporator is satisfactory for its limited applications. However, in
addition to its small surface area, it also has the disadvantage of requiring moving
parts such as the wiper blades which, together with the bearings of the rotating
shaft, need periodic maintenance. Capital costs in terms of dollars per pound of
solvent evaporated also are very high.
12/6/00 11:07 AM Page 10
PLATE TYPE EVAPORATORS

To effectively concentrate an increasing variety of products which differ by industry
in such characteristics as physical properties, stability, or precipitation of solid matter,
equipment manufacturers have engineered a full range of evaporation systems.
Included among these are a number of plate type evaporators (Figure 7).
Plate evaporators initially were developed and introduced by APV in 1957 to
provide an alternative to the tubular systems that had been in use for half a century.
The differences and advantages were many. The plate evaporator, for example,
offers full accessibility to the heat transfer surfaces. It also provides flexible capacity
merely by adding more plate units, shorter product residence time resulting in a
superior quality concentrate, a more compact design with low headroom
requirements, and low installation cost.
Figure 7
These APV plate evaporation systems are made in four arrangements

rising/falling film, falling film, Paravap, and Paraflash and may be sized
for use in new product development or for production at pilot plant or full scale
operating levels.
APV plate type evaporators have been sold commercially for over 40 years.
Approximately 2000 systems have been manufactured by APV for the
concentration of hundreds of different products.
10
12/6/00 11:07 AM Page 11
APPLICATIONS
Although plate evaporators can be used on a broad range of products, the main
application has been with products that are heat sensitive and therefore benefit
from the high HTCs and low residence time. Products that are being processed in
this evaporator include:
Apple juice
Coffee
Pear juice
Amino acids
Fruit purees
Pectin
Beef broths
Gelatin
Pharmaceutical products
Beet juice
Grape juice
Pineapple juice
Betacyclodextrin
Lime juice
Skim milk
Caragenan
Liquid egg
Sugars
Cheese whey
Low alcohol beer
Vegetable juices
Chicken broth
Mango juice
Whey protein
Citrus juice
Orange juice
Whole milk
RISING/FALLING FILM PLATE

This is the original plate type evaporator. The principle of operation for the
rising/falling film plate evaporator (RFFPE) involves the use of a number of plate
packs or units, each consisting of two steam plates and two product plates. These
are hung in a frame which resembles that of a plate heat exchanger (Figure 8).
The first product passage is a rising pass and the second, a falling pass. The steam
plates, meanwhile, are arranged alternately between each product passage.
Figure 8
steam
condensate
product feed
vapor/liquid
product
11
12/6/00 11:07 AM Page 12
The product to be evaporated is fed through two parallel feed ports and is equally
distributed to each of the rising film annuli. Normally, the feed liquor is introduced
at a temperature slightly higher than the evaporation temperature in the plate
annuli, and the ensuing flash distributes the feed liquor across the width of the
plate. Rising film boiling occurs as heat is transferred from the adjacent steam
passage with the vapors that are produced helping to generate a thin, rapidly
moving turbulent liquid film.
During operation, the vapor and partially concentrated liquid mixture rises to the
top of the first product pass and transfers through a 'slot' above one of the
adjacent steam passages. The mixture enters the falling film annulus where gravity
further assists the film movement and completes the evaporation process. The rapid
movement of the thin film is the key to producing low residence time within the
evaporator as well as superior HTCs. At the base of the falling film annulus, a
rectangular duct connects all of the plate units and transfers the evaporated liquor
and generated vapor into a separating device. A flow schematic for a two effect
system is shown in (Figure 9).
Figure 9
12
12/6/00 11:07 AM Page 13
The plate evaporator is designed to operate at pressures extending from

10 psig (1.7 barg) to full vacuum when using any number of effects. However,
the maximum pressure differential normally experienced between adjacent annuli
during single effect operation is 15 psi (1 bar). This, and the fact that the pressure
differential always is from the steam side to the product side, considerably reduce
design requirements for supporting the plates. The operating pressures are
equivalent to a water vapor saturation temperature range of 245F (118C)
downwards, and thus are compatible with the use of nitrile or butyl rubber gaskets
for sealing the plate pack.
Most rising/falling film plate evaporators are used for duties in the food, juice and
dairy industries where low residence time and a temperature lower than 195F
(90C) are essential for the production of quality concentrate. Also, increasing
number of plate evaporators are being operated successfully in both pharmaceutical
and chemical plants on such products as antibiotics and inorganic acids. These
evaporators are available as multi-effect and/or multi-stage systems to allow
relatively high concentration ratios to be carried out in a single pass, nonrecirculatory flow.
The rising/falling film plate evaporator should be given consideration for various
applications that:
Require operating temperatures between 80-212F (26 to 100C)
Have a capacity range of 1000-35,000 lbs/hr

(450 to 16,000 kg/hr) water removal
Have a need for future capacity increase since evaporator capabilities

can be extended by adding plate units or by the addition of extra effects
Require the evaporator to be installed in an area that has limited

headroom as low as 13 ft (4m)
Where product quality demands a low time/temperature relationship
Where suspended solid level is low and feed can be passed

through 50 mesh screen
13
12/6/00 11:08 AM Page 14
A Junior version of the

evaporator (Figure 10) is
available for pilot plant and test
work and for low capacity
production. If necessary, this
can be in multi-effect/multi-stage
arrangements.
Figure 10
FALLING FILM PLATE

Incorporating all the advantages of the original rising falling film plate evaporator
system with the added benefits of shorter residence time and larger evaporation
capabilities, the falling film plate evaporator has gained wide acceptance for the
concentration of heat sensitive products. With its larger vapor ports, evaporation
capacities are typically up to 60,000 lbs/hr (27,000 kg/hr).
The falling film plate evaporator
consists of gasketed plate units
Figure 11
(each with a product and a

steam plate) compressed within
a frame that is ducted to a
separator. The number of plate
units used is determined by the
duty to be handled.
One of the important innovations in this type of evaporator is the patented feed
distribution system (Figure 11). Feed liquor first is introduced through an orifice
(1) into a chamber (2) above the product plate where mild flashing occurs.
This vapor/liquid mixture then passes through a single product transfer hole (3)
into a flash chamber (4) which extends across the top of the adjacent steam plate.
More flash vapor results as pressure is further reduced and the mixture passes in
both directions into the falling film plate annulus through a row of small distribution
holes (5). These assure an even film flow down the product plate surface where
evaporation occurs. A unique feature is the ability to operate the system either in
parallel or in series, giving a two-stage capability to each frame. This is
particularly advantageous if product recirculation is not desirable.
14
12/6/00 11:08 AM Page 15
Figure 12
In the two-stage method of operation, feed enters the left side of the evaporator
and passes down the left half of the product plate where it is heated by steam
coming from the steam sections. After the partially concentrated product is
discharged to the separator, it is pumped to the right side of the product plate
where concentration is completed. The final concentrate is extracted while
vapor is discharged to a subsequent evaporator effect or to a condenser. The
falling film plate is available in an extended form which provides up to 4000 ft2
(370m2) surface area in one frame. A flow schematic for a two effect system
(Figure 12) is shown above. An APV falling film plate evaporator in triple effect
mode (Figure 13) is shown below.
Figure 13. Plant representation. Triple-effect Falling Film Evaporator system followed
by a double-effect forced circulation tubular finisher. A distillation essence recovery
system was provided to recover the key essence components from the juice and in
particular the methyl anthranilate.
15
T H E
12/6/00 11:08 AM Page 16
A P V
P A R A V A P
E V A P O R A T I O N
S Y S T E M S
THE PROCESS
The APV Paravap evaporation system is designed for the evaporation of highly
viscous liquids. The system is often used as a finishing evaporator to concentrate
materials to high solids following a low solids multi-effect or MVR film evaporator.
The main components of the system are a plate heat exchanger, vapor liquid
separator, condenser and a series of pumps (Figure 14). It is designed to operate
as a climbing film evaporator with the evaporation taking place in the plate
passages. Compared with forced circulation evaporators, the pumping costs are
significantly reduced.
Under normal operating conditions the feed is introduced at the bottom of the
plates. As the feed contacts the plate surface, which is heated by either steam
or hot water, the feed starts to evaporate. The narrow gap and corrugations in
the plate passages cause high turbulence and a resulting partial atomization of the
fluid. This reduces the apparent liquid viscosity and generates considerably higher
HTCs than would occur in a shell and tube heat exchanger under similar
conditions. It is particularly effective with non-Newtonian viscous liquids.
Figure 14
16
12/6/00 11:08 AM Page 17
A clear advantage when processing temperature sensitive products is gained with

a Paravap because most duties do not require liquid recirculation.
For most duties the conventional gasketed plate heat exchanger is specified.
However, for duties where the process fluid could attack the gasket, APV can offer
the welded plate pair exchanger which eliminates elastomer gaskets on the
process side.
The Paravap is usually operated in single effect mode although some systems are
operating with double effect.
Since most systems are not physically large, the equipment can often be fully
preassembled on a skid prior to shipment. Preassembly reduces installation time
and, in most cases, significantly lowers the overall project cost.
The Paravap evaporation system is particularly effective in processing the more
viscous products. Often the Paravap can be used in place of a wiped film or thin
film evaporator with a substantial reduction in cost. For duties where severe fouling
can occur on boiling heat transfer surfaces, the process should be performed in a
APV Paraflash system.
Some typical duties that are performed in a Paravap include:
Concentration of sugar solutions to extremely high solids content.

In one case a solids concentration of 98% was achieved.
Removal of water from soaps.
Finishing concentrator on certain fruit purees such as banana and apple.
Concentration of high solids corn syrups.
Removal of solvents from vegetable oils.
Concentration of fabric softeners.
Lignin solutions.
High concentration gelatin.
High concentration chicken broth.
17
T H E
12/6/00 11:08 AM Page 18
A P V
P A R A F L A S H
S Y S T E M S
THE PROCESS
The APV Paraflash evaporation system is designed for the evaporation of liquids
containing high concentrations of solids. In particular, the system is used as a
finishing evaporator to concentrate materials to high solids following a low solids
multi-effect or MVR film evaporator.
The main components of the system are a plate heat exchanger, vapor liquid
separator, condenser and a series of pumps (Figure 15). It is designed to operate
as a forced circulation evaporator with the evaporation being suppressed in the
heating section by back pressure. This back pressure can be generated by a
liquid head above the exchanger or by using an orifice piece or valve in the
discharge from the evaporator. The evaporation then occurs as the liquid flashes
in the entrance area to the separator.
The suppression of boiling, together with the high circulation rate in the plate
heat exchanger, result in less fouling than would occur in other types of
evaporators. This increases the length of production runs between cleanings.
In addition, the narrow gap and corrugations in the plate passages result in far
higher heat transfer rates than would be obtained in shell and tube systems.
Figure 15
18
12/6/00 11:08 AM Page 19
For most duties the conventional gasketed plate heat exchanger is specified.
However for duties where the process fluid could attack the gasket, APV can offer
the welded plate pair exchanger which eliminates elastomer gaskets on the
process side.
The Paraflash can be used either as a single or multiple effect evaporator.
Since many systems are not physically large, the equipment can often be fully
preassembled on a skid prior to shipment. Preassembly reduces installation time
and, in most cases, significantly lowers the overall project cost.
Because of the large range of viscosities that can be handled in a Paraflash, this
form of evaporator can economically handle a wider range of duties than any
other evaporator. In particular, due to the high turbulence and corresponding high
shear rates, the Paraflash system is excellent at handling non-Newtonian fluids with
high suspended solids content.
Some typical duties that are performed in a Paraflash include:
Concentration of wash water from water based paint plants to recover

the paint and clean the water.
Removal of water from dyestuffs prior to drying.
Finishing concentrator on waste products from breweries and distilleries.
Concentration of brewers yeast.
Concentration of kaolin slurries prior to drying.
Recovery of solvents in wastes from cleaning operations.
Evaporation of solvents from pharmaceutical products.
Crystallization of inorganic salts.
Cheese whey.
19
12/6/00 11:08 AM Page 20
V A
R
S
A
E
T
L
O
E
The choice of an evaporator best suited to the duty on hand requires a number
of steps. Typical rules of thumb for the initial selection are detailed below.
A selection guide (Figure 16), based on viscosity and the fouling tendency
of the product is shown below on next page.
MODE OF EVAPORATION
The user needs to select one or more of the various types of evaporator modes
that were described in the previous section. To perform this selection, there are a
number of rules of thumb which can be applied.
Falling film evaporation:

either plate or tubular, provides the highest heat transfer coefficients.
is usually the mode chosen if the product permits.
will usually be the most economic.
is not suitable for the evaporation of products with viscosities over 300cp.
is not suitable for products that foul heavily on heat transfer surfaces
during boiling.
Forced circulation evaporators:

can be operated up to viscosities of over 5,000cp.
will significantly reduce fouling.
are expensive; both capital and operating costs are high.
Paravap evaporators:
are suitable for viscosities up to 10,000cp for low fouling duties.
are suitable for very high viscosities, i.e., over 20,000cp, usually the only
suitable evaporation modes are the wiped film and thin film systems.
20
12/6/00 11:08 AM Page 21
FILM EVAPORATORSPLATE OR TUBULAR
Plate evaporators:
provide a gentle type of evaporation with low residence times and are
often the choice for duties where thermal degradation of product can occur.
often provide enhanced quality of food products.
require low headroom and less expensive building and installation costs.
are easily accessed for cleaning.
provide added flexibility, since surface area can easily be added or removed.
Tubular evaporators:
are usually the choice for very large evaporators.
are usually the choice for evaporators operating above 25 psia (1.7 bar).
are better at handling large suspended solids.
require less floor space than plate evaporators.
have fewer gasket limitations.
FORCED CIRCULATION EVAPORATORSPLATE OR TUBULAR
Plate systems will provide much higher HTCs for all duties. With viscous products,
the plate exhibits vastly improved performance compared with a tubular.
Tubular systems must be selected when there are particulates over 2mm diameter.
THE APV PARAVAP
For low fouling viscous products such as high brix sugar, the Paravap
system is always the preferred solution.
High
Wiped Film
Figure 16
This diagram shows a
selection guide based on
the viscosity and fouling
tendency of the product.
Viscosity
Paravap
Film
Low
Forced Circulation Plate

or Tubular
Recirculated
Film
Fouling
High
21
12/6/00 11:08 AM Page 22
MATERIALS OF CONSTRUCTION
The two parameters which control the selection of the material of construction are
corrosion and ease of cleaning.
All evaporators for hygienic duties must be capable of being frequently cleaned in
place. In most cases, this means rinsing the equipment with water, followed by
washing with caustic and then acid cleaning agents, and finally, a further rinsing
with water. It is important, particularly with dairy and meat products, that the
evaporator is completely cleaned of all deposits. The cleaning processes eliminate
the use of carbon steel as the material of construction. Most hygienic evaporators
are manufactured in either 304 or 316 stainless steel.
Corrosion is often a major problem with chemical duties and some hygienic
applications. A particular problem with evaporators is the range of concentration
of solids in the process fluid, since the corrosive component will be concentrated
as it passes through the evaporator. In some evaporators, the concentration range
can be as high as 50 to 1. For example, waste water with a chloride content of
40ppm in the feed would have 2000ppm in the product. While stainless steel
would be acceptable for the initial stages of evaporation, a more corrosion
resistant material would be required for the last one or two stages.
Corrosion is also a major consideration in the selection of gasket materials. This
is particularly important with plate evaporators with elastomeric gaskets sealing
each plate. Many solvents such as chlorinated and aromatic compounds will
severely attack the gaskets. A less obvious form of attack is by nitric acid. This is
important since nitric acid can be present in some cleaning materials. While
concentrations of about 1% up to 140F (60C) can be accepted, it is best to
eliminate nitric acid from cleaning materials. Phosphoric and sulfamic acids are
less aggressive to gaskets.
22
12/6/00 11:08 AM Page 23
It is not the purpose of this handbook to provide guidelines for the selection of
materials of construction. The reader is referred to the APV Corrosion Handbook,
as well as the many publications issued by the material manufacturers.
Typical materials of construction for a number of evaporator applications are
shown below:
PRODUCT
MATERIAL OF CONSTRUCTION
Most dairy and food products

Most fruit juices
Sugar products
Foods containing high salt (NaCl)
304/316 stainless steel

316 stainless steel
Carbon steel /304/316
Titanium/Monel
High alloy stainless steels
Duplex stainless steels
Stress relieved carbon steel
Nickel
Graphite/Rubber lined carbon steel
Caustic soda < 40%

Caustic soda high concentration
Hydrochloric acid
In some cases, the type of evaporator is controlled by the materials of construction.

For example a sulfuric acid evaporator, where the acid concentration can reach
50%, would utilize graphite tubular heat exchangers and non-metallic separators
and piping.
23
12/6/00 11:08 AM Page 24
E V A P O R A T O R
C O N F I G U R A T I O N S
E N E R G Y
F O R
C O N S E R V A T I O N
Conservation of energy is one major parameter in the design of an evaporator

system. The larger the evaporation duty, the more important it is to conserve energy.
The following techniques are available:
MULTI-EFFECT EVAPORATION
Multi-effect evaporation uses the steam produced from evaporation in one effect
to provide the heat to evaporate product in a second effect which is maintained
at a lower pressure (Figure 17). In a two effect evaporator, it is possible to
evaporate approximately 2 kgs of steam from the product for each kg of steam
supply. As the number of effects is increased, the steam economy increases. On
some large duties it is economically feasible to utilize as many as seven effects.
Increasing the number of effects, for any particular duty, does increase the
capital cost significantly and therefore each system must be carefully evaluated.
In general, when the evaporation rate is above 3,000 lbs/h (1,350 kg/h),
multi-effect evaporation should be considered.
Figure 17
24
12/6/00 11:08 AM Page 25
THERMO VAPOR RECOMPRESSION (TVR)

When steam is available at pressures in excess of 45 psig (3 barg) and
preferably over 100 psig (7 barg), it will often be possible to use thermo vapor
recompression. In this operation, a portion of the steam evaporated from the
product is recompressed by a steam jet venturi and returned to the steam chest of
the evaporator. A system of this type can provide a 2 to 1 economy or higher
depending on the product the steam pressure and the number of effects over
which TVR is applied.
TVR is a relatively inexpensive technique for improving the economy of evaporation.
TVR can also be used in conjunction with multi-effect to provide even larger
economies (Figure 18). Shown in (Figure 19) are the economies that can
be achieved.
Thermocompressors are somewhat inflexible and do not operate well outside the
design conditions. Therefore if the product is known to foul severely, so that the
heat transfer coefficient is significantly reduced, it is best not to use TVR. The
number of degrees of compression is too small for materials that have high
boiling point elevation.
Figure 18
25
12/6/00 11:08 AM Page 26
Figure 19
MECHANICAL VAPOR RECOMPRESSION (MVR)

Thermodynamically, the most efficient technique to evaporate water is to use
mechanical vapor thermocompression. This process takes the vapor that has been
evaporated from the product, compresses the vapor mechanically and then uses
the higher pressure vapor in the steam chest (Figure 20).
The vapor compression is carried out by a radial type fan or a compressor. The
fan provides a relatively low compression ratio of 1:30 which results in high heat
transfer surface area but an extremely energy efficient system. Although higher
compression ratios can be achieved with a centrifugal compressor, the fan has
become the standard for this type of equipment due to its high reliability, low
maintenance cost and generally lower RPM operation.
Figure 20
26
12/6/00 11:08 AM Page 27
This technique requires only enough energy to compress the vapor because the
latent heat energy is always re-used. Therefore, an MVR evaporator is equivalent
to an evaporator of over 100 effects. In practice, due to inefficiencies in the
compression process, the equivalent number of effects is in the range 30 to 55
depending on the compression ratio.
The energy supplied to the compressor can be derived from an electrical motor,
steam turbine, gas turbine and internal combustion engine. In any of the cases the
operating economics are extremely good.
Since the costs of the compressors are high, the capital cost of the equipment will
be significantly higher than with multi-effect. However in most cases, for medium
size to large evaporators, the pay back time for the addition capital will only
be 1 to 2 years.
Like the one TVR, the two MVR system is not appropriate for high fouling duties or
where boiling point elevation is high.
COMBINATION OF FILM AND

FORCED CIRCULATION EVAPORATORS.
The most economic evaporators utilize falling film tubulars or plates, with either TVR
or MVR. However with many duties, the required concentration of the final product
requires a viscosity that is too high for a film evaporator. The solution is to use film
evaporation for the pre-concentration and then a forced circulation finisher
evaporator to achieve the ultimate concentration; e.g., a stillage or spent distillery
wash evaporator. The material would typically be concentrated from 4% to 40% in
a falling film evaporator and then from 40% to 50% in a forced circulation
evaporator. Usually the finisher would be a completely separate evaporator since
the finisher duty is usually relatively low. In the duty specified above, almost 98%
of the evaporation would take place in the high efficiency
film evaporator.
For cases where the finisher load is relatively high, it is possible to incorporate
the forced circulation finisher as one of the effects in a multi-effect evaporator.
However this is an expensive proposition due to the low coefficients at the
high concentration.
27
12/6/00 11:08 AM Page 28
R E S I D E N C E
F I L M
T I M E
I N
Since many pharmaceutical, food and dairy products are extremely heat
sensitive, optimum quality is obtained when processing times and temperatures
are kept as low as possible during concentration of the products. The most critical
portion in the process occurs during the brief time that the product is in contact
with a heat transfer surface which is hotter than the product itself. To protect
against possible thermal degradation, the time/temperature relationship therefore
must be considered in selecting the type and operating principle of the evaporator
to be used.
For this heat sensitive type of application, film evaporators have been found to
be ideal for two reasons. First, the product forms a thin film only on the heat
transfer surface rather than occupying the entire volume, greatly reducing
residence time within the heat exchanger. Second, a film evaporator can operate
with as low as 6F (3.5C) steam-to-product temperature difference. With both the
product and heating surfaces close to the same temperature, localized hot spots
are minimized.
As previously described, there are rising film and falling film evaporators as well
as combination rising/falling film designs. Both tubular and plate configurations
are available.
COMPARISON OF RISING FILM

AND FALLING FILM EVAPORATORS
In a rising film design, liquid feed enters the bottom of the heat exchanger and
when evaporation begins, vapor bubbles are formed. As the product continues up
either the tubular or plate channels and the evaporation process continues, vapor
occupies an increasing amount of the channel. Eventually, the entire center of the
is filled with vapor while the liquid forms a film on the heat transfer surface.
28
12/6/00 11:08 AM Page 29
The effect of gravity on a rising film evaporator is twofold. It acts to keep the
liquid from rising in the channel. Further, the weight of the liquid and vapor in
the channel pressurizes the fluid at the bottom and with the increased pressure
comes an increase in the boiling point. A rising film evaporator therefore requires
a larger minimum T than a falling film unit.
The majority of the liquid residence time occurs in the lower portion of the channel
before there is sufficient vapor to form a film. If the liquid is not preheated above
the boiling point, there will be no vapor. And since a liquid pool will fill the entire
area, the residence time will increase.
As liquid enters the top of a falling film evaporator, a liquid film formed by gravity
flows down the heat transfer surface. During evaporation, vapor fills the center of
the channel and as the momentum of the vapor accelerates the downward
movement, the film becomes thinner. Since the vapor is working with gravity, a
falling film evaporator produces thinner films and shorter residence times than a
rising film evaporator for any given set of conditions.
TUBULAR AND PLATE FILM EVAPORATORS

When compared to tubular designs, plate evaporators offer improved residence
time since they carry less volume within the heat exchanger. In addition, the height
of a plate evaporator is less than that of a tubular system.
29
12/6/00 11:12 AM Page 30
ESTIMATING RESIDENCE TIME

It is difficult to estimate the residence time in film evaporators, especially rising film
units. Correlations, however, are available to estimate the volume of the channel
occupied by liquid. Formula (1) is recommended for vacuum systems.
For falling film evaporators, the film thickness without vapor shearing can be
calculated by Formula (2).
Since the film is thin, this can be converted to liquid volume fraction in a tubular
evaporator by Formula (3).
For a falling film plate evaporator, Formula (4) is used. As liquid travels down the plate
and evaporation starts, vapors will accelerate the liquid. To account for this action, the
rising film correlation is used when the film thickness falls below that of a falling film
evaporator. In practice, the film thickness may be less than estimated by either method
because gravity and vapor momentum will act on the fluid at the same time.
Once the volume fraction is known, the liquid residence time is calculated by
formula (5). In order to account for changing liquid and vapor rates, the volume
fraction is calculated at several intervals along the channel length. Evaporation is
assumed to be constant along with channel length except for flash due to high
feed temperature.
SYMBOLS
A
d
g
L
m
RL
qL
t
L
V
cross sectional area

tube diameter
gravitational constant
tube length
film thickness
liquid volume fraction
liquid rate
time
liquid wetting rate
liquid density
vapor density
liquid viscosity
local weight fraction of vapor
FORMULAS
(1)
1+
30
1y
y
3
g L ( L v )
(2)
m=
(3)
RL =
4m
d
(4)
RL =
2m
Z
(5)
t=
References
a) HTRI report, BT-2, pg. 7 (May
1978)
b) Perry's Chemical Engineer's
RL = 1
RL AL
qL
) ( 2 )
.5
/3
CONTACT
TIME
12/6/00 11:12 AM Page 31
RISING
RISING
FALLING
FALLING
FILM TUBULAR FILM PLATE (C) FILM TUBULAR FILM PLATE
1st effect
2nd effect
3rd effect
4th effect
Total
Contact
Time
88
62
118
236 (A)
47 (A)
20
30
78 (A)
23
22
15
123 (A)
16 (A)
13
9
62 (B)
504
175
183
100
(A) two stages
(B) three stages
(C) plate gap .3 in (7.5mms)
The table above shows a comparison of contact times for typical four-effect
evaporators handling 40,000 lb/h (18,000 kg/h) of feed. The tubular designs
are based on 2 in. (51 mm) OD tube, 30 feet (9m) long. Incidentally, designs
using different tube lengths do not change the values for a rising film tubular system.
The given values represent total contact time on the evaporator surface, which is
the most crucial part of the processing time. Total residence time would include
contact in the preheater and separator, as well as additional residence within
interconnecting piping.
While there is no experimental data available to verify these numbers, experience
with falling film plate and tubular evaporators shows that the values are
reasonable. It has been noted that Formula (2) predicts film thicknesses that are
too high as the product viscosity rises. Therefore, in actuality, 4th effect falling film
residence times probably are somewhat shorter than charted.
SUMMARY
Film evaporators offer the dual advantages of low residence time and low
temperature difference which help assure a high product quality when
concentrating heat sensitive products. In comparing the different types of film
evaporators that are available, falling film designs provide the lowest possible
T, and the falling film plate evaporator provides the shortest residence time.
31
12/6/00 11:12 AM Page 32
D E S I G N I N G
E N E R G Y
F O R
E F F I C I E N C Y
Although the concentration of liquids by evaporation is an energy intensive

process, there are many techniques available, as detailed in previous sections, to
reduce the energy costs. However, increased energy efficiency can only be
achieved by additional capital costs. As a general rule, the larger the system, the
more it will pay back to increase the thermal efficiency of the evaporator.
The problem is to select the correct technique for each application.
The main factors that will affect the selection of the technique are detailed below.
EVAPORATION RATE
The higher the capacity of the evaporator, the more the designer can justify
complex and expensive evaporation systems in order to provide high
energy efficiency.
For evaporator design purposes, the capacity is defined as the evaporation rate
per hour. However, in some applications such as seasonal fruit juice processors,
the equipment is only operated for part of the year. This means that an expensive
evaporator is idle for part of the year. The economic calculation has to include
annual operating hours.
For low capacities the designer is less concerned about energy efficiency. If the
evaporation rate is below 2,200 lb/h (1000 kg/h), it is difficult to justify multieffect evaporation. Usually a single-effect evaporator, often with thermo vapor
recompression (TVR), is the system of choice at this capacity.
In many cases, mechanical vapor recompression (MVR) is the most efficient
evaporator. However, these systems operate at a low temperature difference,
which results in high heat transfer area. Also MVR requires either a centrifugal
compressor or a high pressure fan which are expensive equipment items.
These cannot usually be justified for low capacity evaporators.
32
12/6/00 11:12 AM Page 33
STEAM/ELECTRICITY COSTS
For medium to large duties, a selection has to be made between multi-effect and
MVR. A critical parameter that will affect this selection are steam costs relative to
electricity costs. Providing process conditions are favorable, MVR evaporation will
be more economic, particularly in areas where the electricity cost is low, such as
localities around major hydro generating plants. However if low cost steam is
available, even at pressures as low as atmospheric, then multi-effect evaporation
will be usually more economic due to the lower capital cost.
STEAM PRESSURE
The availability of steam at a medium pressure of about 100 psig (7 barg),
permits the efficient use of TVR either on a single or multi-effect evaporator. TVR
can be applied across one, two or even three effects. This is the simplest and
least costly technique for enhancing evaporator efficiency. The effectiveness
declines significantly as the available steam pressure is reduced.
MATERIAL OF CONSTRUCTION
The majority of evaporators are made in 304 or 316 stainless steel. However
there are occasions that much more expensive materials of construction are
required, such as 904L, 2205, nickel, Hastelloy C, titanium and even graphite.
These expensive materials skew the economic balance, with the capital cost
becoming more significant in the equation. Typically MVR would become
less economic as the material cost increases, due to the size of the heat
exchangers required.
33
12/6/00 11:12 AM Page 34
P H Y S I C A L
P R O P E R T I E S
There are a number of physical properties that can severely influence the selection
of an evaporator.
BOILING POINT ELEVATION

A boiling point elevation of over 5F (3C) essentially eliminates MVR
evaporators from consideration. This can be partially circumvented by using MVR as
a pre concentrator. Once the concentration is sufficient to produce significant boiling
point elevation, the final evaporation would be performed in a steam driven finisher.
PRODUCT VISCOSITY
High product viscosity of over 300 to 400cp usually eliminates falling film
evaporators in favor of forced circulation. Forced circulation requires a higher
temperature difference, which eliminates MVR. TVR is used on some duties.
PRODUCT FOULING
Both MVR and TVR are not particularly suitable for duties where severe fouling of
heat transfer surfaces occurs over a short time period. The performance of these
evaporators will fall off more rapidly than with a multi-effect system. Forced
circulation evaporators with suppressed boiling usually perform better with high
fouling than film evaporators.
TEMPERATURE SENSITIVE PRODUCTS

Many products, particularly in the food industry, are prone to degradation at
elevated temperatures. The effect is usually made worse by extended residence time.
This problem limits the temperature range for multi-effect systems. For example on
a milk evaporator, the temperature is limited to a maximum of 160F (71C).
Since a typical minimum boiling temperature is 120F (49C), there is a limited
temperature difference to perform the evaporation. This type of duty is suitable for
MVR since the evaporation occurs at essentially the same temperature. Although a
lower operating temperature increases the size of the major equipment, MVR is the
most economic solution for large capacity dairy evaporators.
34
12/6/00 11:12 AM Page 35
In many cases the selection of the energy conservation technique is obvious.

However, for many applications it is necessary to evaluate a number of techniques
in detail before a decision can be made.
The following case study illustrates the various options to save energy using
different techniques.
The duty is to concentrate skim milk from 8% solids to 48% by evaporation.
The feed rate is 100,000 lb/h (45,500 kg/h). The data shown in the table
below summarizes the performance and costs for a straight 5 effect evaporator,
a 5 effect evaporator with TVR across 3 effects, and a mechanical vapor
recompression evaporator.
No pasteurizer is included in this cost comparison.
Annual operating costs are based on 7,000 h/year of operation, with a steam
cost of $5.50/1000 lb (454 kg) and electricity at $0.068/kwh.
Evaporation
Steam Consumed
Absorbed power
Annual costs
Steam
Electricity
Total
Capital costs
Equipment
lb/h
kg/h
lb/h
kg/h
kw
5 EFFECT
5 EFFECT WITH TVR
MVR
83,000
37,900
17,000
7,700
70
83,000
37,900
11,000
5,000
60
83,000
37,900
0
0
560
$654,500
$33,300
$687,800
$423,500
$28,560
$452,060
0
$266,560
$266,560
$2,200,000
$2,600,000
$2,700,000
The examples illustrate that with a higher capital investment, it is possible to

significantly reduce the operating costs of the equipment. However the most
economic selection is controlled by the steam and electricity prices. For example,
if the dairy is located alongside an electric co-generation plant, the steam cost
would be reduced considerably lower, and a steam heated evaporator would be
the most economic.
A less important, but still significant factor, is the cost of cooling water. An MVR
evaporator requires virtually no cooling water. On a steam heated system the
cooling water requirement is about 6 US gallons per lb (.05 m3 per kg) of
steam applied.
35
12/6/00 11:12 AM Page 36
M E C H A N I C A L
V A P O R
R E C O M P R E S S I O N
E V A P O R A T O R S
Mechanical vapor recompression (MVR) evaporation provides an extremely
energy efficient technique for the concentration of solids in water. Usually the
capital cost of an MVR system is higher than a comparable steam driven
evaporator. However, as the capacity of the system increases the relative cost
difference decreases. Although MVR evaporators are seldom chosen for small
duties, the concept is often used for medium to large capacity evaporators.
MVR DEFINED
The basic principle of MVR is to remove the steam that is evaporated from the
product, compress it in a mechanical device, and use the higher pressure steam,
which has a corresponding higher saturation temperature, to provide the heating
medium for the evaporation (Figure 21). No steam input is required once the
system is operating. The small difference in enthalpy between the vapors on the
condensing and boiling sides is the theoretical energy required to perform the
evaporation. Essentially, the process re-uses the latent heat of the vapors. The
theoretical thermal efficiency of MVR can exceed that of a 100 effect evaporator,
although there are a number of practical limitations, such as
compressor and motor efficiencies which lower
the achievable efficiency.
The mechanical device
can be a centrifugal
compressor for applications
with high compression ratios,
or a fan for lower compression
ratios. For either device, the
drive can be an electric motor,
steam turbine, internal
combustion engine or
gas turbine.
36
Figure 21
12/6/00 11:12 AM Page 37
C
T=243F
SUPERHEAT
AVAILABLE FOR
GENERATING
EXCESS VAPOR
11.2 BTU/LB
1153.4
DE
SU
PE
RH
EA
IDEAL
T
-1
COMPRESSION
7.
2
PS
ACT
I
UAL
COM
PRE
SSIO
N
PS
IA
14
.7
COMPRESSOR
ENERGY
INPUT 14.1
BTU/LB
H-ENTROPY BTU/LB
1164.6
T=220F
T=212F
1150.5
ENTHALPY
DIFFERENCE
AT CONDENSING
TEMPERATURES
2.9 BTU/LB
SUPERHEATED
VAPOR
SA
TU
RA
TE
VA
P
OR
VAPOR
LIQUID
MIXTURE
Figure 22
1.7442
1.7568
1.7596
S-ENTROPY BTU/LBF
THERMODYNAMICS OF MVR
The process is best explained by reference to the Mollierenthalpy/entropy
diagram for steam (Figure 22).
The vapor evaporated from the product is represented on the Mollier diagram
at point A. The actual values in US and metric units are presented on
Table 1a and 1b. The vapor enters the compressor at point A. The vapor is then
compressed to the higher pressure, at constant entropy at point B. The compressor,
which in this case is a fan, has inefficiencies which results in an increase in
entropy above that of the entropy at inlet. This is represented by point C. Vapor
at point C is at the required pressure for the steam jacket of the condenser.
However, it is superheated and must be cooled in order to condense in the
evaporator. This cooling can be performed on the heat transfer surface of the
evaporator. However, since desuperheating HTCs are usually low, the
desuperheating is usually performed by the introduction of a spray of condensate
into the vapor duct. This condensate vaporizes as the vapor is cooled back to the
saturation temperature, and generates more vapor. This condition is represented by
point D. At this point most of the vapor is condensed in the evaporator. However,
there is an excess of vapor, which is required for heat loss and/or preheat duties.
Any balance is condensed or vented.
37
12/6/00 11:12 AM Page 38
PROPERTIES OF WATER VAPOR

Pressure-PSIA
State
Temperature F
H-Enthalpy Vapor BTU/LB
Latent Heat BTU/LB
H-Enthalpy Liquid BTU/LB
S-Enthalpy BTU/LB F
14.7
17.2
17.2
Saturated
212
1150.5
970.3
180.2
1.7568
Saturated
220
1153.4
965.2
188.2
1.7442
Superheated
243
1164.6
1.7596
Table 1a. Properties of Water Vapor.
PROPERTIES OF WATER VAPOR

Pressure-BAR
State
Temperature C
H-Enthalpy Vapor Kcals/Kg
Latent Heat Kcals/Kg
H-Enthalpy Liquid Kcals/Kg
S-Enthalpy Kcals/Kg C
1.17
1.17
Saturated
100
639.1
539.0
100.1
1.7568
Saturated
104
640.8
536.2
104.6
1.7442
Superheated
117
647.0
1.7596
Table 1b. Properties of Water Vapor.
In this example, the heat required to evaporate the water is 970.3 Btu
(539.0 Kcals). However the compressor input is only 14.1 Btu (7.8 Kcals), with
motor and gearbox losses increasing this to 14.7 Btu (8.16). The equivalent
economy is 66 to 1.
It should be noted that pressure losses through the evaporator ducting, calandria
and separator must be absorbed. This can be achieved by either a higher boost
from the compressor at a higher power, or by accepting a lower temperature
difference and increasing the surface area of the calandria.
38
12/6/00 11:12 AM Page 39
TYPES OF COMPRESSION EQUIPMENT

To a large extent, the development of this technology has been guided by the
capabilities of the various types of compressors. The key to the design is the
temperature difference that is available for the evaporator. Table 2 shows the
temperature difference for various compression ratios at two different boiling
temperatures. It is this temperature difference that is available as the driving force
for evaporator, less a small amount required in the form of lost pressure around the
system. The original MVR systems used compressors with compression ratios of
about 1.4, which limited the available temperature difference to 13 to 18F (7 to
10C). This limits the MVR to single effect operation. More advanced centrifugal
compressors were developed in the 1970s, which provided compression ratios of
approximately 2. This provided a much higher temperature difference, which
allowed operation with 2 and 3 effects. This reduces the flow to the compressor
and increases the operating efficiency.
COMPRESSION RATIO
1.2
1.4
1.6
1.8
2.0
SATURATED T AT BOILING TEMPERATURES

130F
55C
212F
100C
6.9
12.9
18.2
23.0
27.3
3.8
7.2
10.1
12.8
15.1
9.3
17.5
24.7
31.2
37.2
5.2
9.7
13.7
17.3
20.7
Table 2. Saturated T at Various Compression Ratios, F and C.
A number of evaporators were built with the higher compression systems in multieffect mode. Unfortunately, the reliability of the compressors became a problem.
Because the compressor operates at high speed, it has to be protected from
impingement of water droplets. This usually requires a mist eliminator in the
separator, followed by a superheater. Any solids carryover will have a detrimental
effect on the compressor. In addition, the designer must take care to prevent
unstable compressor operation (surging). While the majority of the compressors
functioned well, there were a few catastrophic compressor failures. These failures
caused engineers to review alternative equipment.
The answer to the compressor problem was to use a fan. This equipment operates
at a lower speed and is less vulnerable to damage from droplets. Fans are also
far less likely to surge. When operated with a variable frequency drive, the fans
39
12/6/00 11:12 AM Page 40
provide far greater flexibility than compressors. The only disadvantage to the fan is
that compression ratios are limited to about 1.45. This results in a low available
temperature difference and therefore a high heat transfer area. However, the
energy efficiency of such systems is very high with the equivalent of 55 effects
achievable for many duties.
POWER REQUIREMENTS
The compressor power requirements to evaporate 1000 lb/h (454 kg/h) of
steam at various compression ratios and temperatures are shown in
Tables 3a and 3b. Similar data for fans are shown in Tables 4a and 4b.
These data correspond quite well with installed MVR systems.
A more detailed comparison between three actual systems is shown in Table 5. The more
energy efficient system is the single effect fan with a low compression ratio. However, the
low temperature difference will result in high heat transfer area in the calandria. In most
cases the added capital cost will be justified by lower operating costs.
COMPRESSORS
Boiling Temp 130F
Boiling Temp 170F
Boiling Temp 212F
CR
kw
CR
kw
CR
kw
1.3
1.4
1.6
1.8
2.0
2.2
10.00
12.91
18.21
22.98
27.31
31.30
7.0
9.1
12.9
16.5
19.8
22.9
1.3
1.4
1.6
1.8
2.0
2.2
11.65
15.03
21.23
26.81
31.89
36.57
7.5
9.7
13.8
20.0
21.1
27.2
1.3
1.4
1.6
1.8
2.0
2.2
13.53
17.47
24.69
31.20
37.16
41.31
7.9
10.3
14.7
18.7
22.5
24.9
Table 3a. Power Vs T for Centrifugal Compressors Based on 1000 lb/h of Steam Evaporated.
COMPRESSORS
Boiling Temp 55C
Boiling Temp 77C
Boiling Temp 100C
CR
kw
CR
kw
CR
kw
1.3
1.4
1.6
1.8
2.0
2.2
5.55
7.17
10.11
12.77
15.17
17.39
15.4
20.0
28.5
36.3
43.5
50.3
1.3
1.4
1.6
1.8
2.0
2.2
6.47
8.35
11.79
14.89
17.71
20.37
16.4
21.3
30.4
38.7
46.4
53.6
1.3
1.4
1.6
1.8
2.0
2.2
7.51
9.71
13.71
17.33
20.64
22.95
17.5
22.7
32.4
41.3
49.4
57.1
Table 3b. Power Vs T for Centrifugal Compressors Based on 454 kg/h of Steam Evaporated.
40
12/6/00 11:12 AM Page 41
SMALL MVR EVAPORATORS

For small systems, rotary blowers were occasionally specified in an attempt to
make MVR economic at evaporation capacities less than 15,000 lb/h
(7000 kg/h). While there were cost savings, there were also reliability problems
with this equipment for this particular application. The conclusion remained that for
small systems, it is usually best to use steam driven evaporators.
FANS
Boiling Temp 130F
CR
1.1
1.2
1.3
T
3.59
6.91
10.00
kw
2.22
4.31
6.28
Boiling Temp 170F

CR
1.1
1.2
1.3
T
4.17
8.04
11.65
kw
2.38
4.60
6.71
Boiling Temp 212F

CR
1.1
1.2
1.3
T
4.85
9.34
13.53
kw
2.54
4.92
7.15
Table 4a. Power Vs T for Fans Based on 1000 lb/h of Steam Evaporated.
FANS
Boiling Temp 55C
Boiling Temp 77C
Boiling Temp 100C
CR
kw
CR
kw
CR
kw
1.1
1.2
1.3
1.99
3.84
5.56
4.90
9.49
13.81
1.1
1.2
1.3
2.32
4.47
6.47
5.22
10.12
14.75
1.1
1.2
1.3
2.69
5.19
7.52
5.58
10.81
15.73
Table 4b. Power Vs T for Fans Based on 454 kg/h of Steam Evaporated.
SINGLE EFFECT DOUBLE EFFECT TRIPLE EFFECT
FAN
CENTRIFUGAL
CENTRIFUGAL
Compression Ratio
Total T Available
Vapor to Compressor
Total Power Kw
Equivalent Steam
Equivalent
Steam Economy
Average T Per Effect
Before Losses
1.2
6.9F (3.8C)
60,000 lb/h
(27,300 kg/h)
280
870 lb/h
(395 kg/h)
1.6
18.2F (10.1C)
30,000 lb/h
(13,650 kg/h)
390
1315 lb/h
(600 kg/h)
2.0
27.3F (15.2C)
20,000 lb/h
(9,090 kg/h)
400
1347 lb/h
(612 kg/h)
69
6.9F
(3.8C)
45.6
9.1F
(5.1C)
44.5
9.1F
(5.1C)
NOTE: In this example, the fan horsepower is lower than either of the centrifugal
designs, but the lower T required the greater the surface area.
Table 5. Comparison of Typical MVR Designs Approximate boiling temperature

130F (55C) evaporation rate60,000 lb/hr (27,000 kg/h).
41
12/6/00 11:12 AM Page 42
I N D U S T R I A L
C H E M I C A L
F O R
A N D
A P P L I C A T I O N S
The APV range of evaporators covers many duties in the concentration of

chemicals and industrial products, with both film and forced circulation systems
being available as required.
Film evaporators are used when there is little or no risk of fouling of the heating
surfaces. Where such a risk is present, forced circulation units are recommended.
All designs are suitable for multi-effect evaporation. At low concentrations,
mechanical vapor recompression can be employed.
After selecting the type of evaporator required for a particular duty, the most
important factor is the selection of the materials of construction. Many duties
can be handled with 316 stainless steel. For some applications where chloride
ions are present, higher grades of stainless steel, such as 904L, can be an
economic selection.
Certain products are so corrosive that they cannot be processed in
conventional metals. As an example,
concentration of a sulfuric acid solution
of up to 50% at 302F (150C)
would call for main plant items of
filament wound fiberglass reinforced
epoxy resin, and heating and cooling
surfaces of impervious graphite.
If the sulfuric acid solution is between
50 and 80% with temperatures up to
230F (110C), main plant items should
be lead-lined mild steel protected with
refractories or carbon tiles. Heat transfer
surfaces again would be of impervious
graphite. A typical system (Figure 23)
is shown here. It should be noted that APV
does not market non-metallic evaporators.
42
Figure 23
12/6/00 11:12 AM Page 43
TITANIUM SULFATE
The production of titanium dioxide pigments involves reaction between sulfuric
acid and the ore which contains iron, titanium sulfate and other compounds.
After pretreatment, which includes the crystallization of iron as ferrous sulfate,
the liquor is heated and hydrolyzed to precipitate titanium dioxide. Prior to this
operation, the concentration of liquor has to be adjusted by the evaporation of
water. It is essential that this process takes place in an evaporator with short
heat contact times in order to avoid the premature hydrolysis that occurs with
prolonged heating, which subsequently causes fouling of the heat surface and
blockage of the tubes. Although the liquor contains a high proportion of sulfuric
acid, the presence of other ions in solution may inhibit corrosion, so that copper
often can be used for heat transfer surfaces. Titanium is another material used
for this application.
Generally, single or multiple effect rising film evaporators are used for this duty, the
number of effects being determined by throughput and by assessing the cost of
operation against the increase in capital required for additional equipment.
In some cases, it is economically attractive to operate the evaporator as a single
effect unit at atmospheric pressure using the vapor given off for preheating. The
liquor is discharged at a temperature in excess of 212F (100C), reducing the
subsequent thermal load at the hydrolysis stage.
PHOSPHORIC ACID
Phosphoric acid can be produced by the digestion of phosphate rock (calcium
phosphate and fluoride among others) in sulfuric acid, better known as the "wet
process" acid. Since calcium sulfate normally is a constituent, scaling must be
considered. Phosphate rock varies in composition, and in general, periodic
cleaning is required even in forced circulation evaporators.
Sulfuric acid plants often are located along coastal areas, and a further problem
in concentration stems from the use of sea water in the direct contact condensers.
With silica present in the phosphate rock, fluorine reacts to form hydrofluorosilicic
acid (H2SiF6) which in turn, forms a sodium salt from the NaCl. Sodium fluorosilicic
can block the condensers.
43
12/6/00 11:12 AM Page 44
AMMONIUM NITRATES
This material has several significant properties:
Low viscosity which allows it to be concentrated to

99+% w/w when it is prilled.
Above 95%, ammonium nitrate has an extremely high boiling point

elevation which requires exceedingly high steam pressures for heating.
This presents considerable mechanical problems.
Any organic impurity has the potential for explosion, such that extra low
carbon stainless steels must be used for heat transfer surfaces, and the use
of mineral oils for heating is excluded.
The type of evaporator best suited for ammonium nitrate depends upon the
initial and final concentrations. For the range below 70% and up to 80-85%,
rising film multi-effect evaporator units have been used successfully. For 80-96%
concentrations, conventional falling film systems have been employed. Above
96%, however, falling film with a heated air sweep would be used due to
partial pressure conditions. In areas of relatively low humidity, 99+% water
to water can be achieved.
AMMONIUM SULFATE
Ammonium sulfate is used in battery spacer plate production and also has
been crystallized. In this process, small but regular sized crystals are mixed
with a PVC type plastic and dissolved out of the final sheet which then is used
as spacer plate. Stainless steel has been successfully employed as the material
of construction.
BARIUM SALTS
The production of barium salt involves the use of sodium sulfide, a material
which closely resembles caustic soda in both physical and corrosive properties.
It generally is concentrated in a high vacuum crystallizer for the production of
barium hydroxide with rubber lined mild steel being used as the material of
construction due to corrosion considerations. With liquid temperatures below
72F, two hydrates--mono and pentacan be produced on separate flakers.
44
12/6/00 11:12 AM Page 45
GLYCERINE
Sweet water glycerine containing no NaCl has been handled in simple stainless
steel film evaporators by salt and oleo chemical producers. For sodium chloride
bearing liquors as in spent lye for industrial detergent and soap manufacture,
cupronickel alloys must be used.
When the glycerine is contaminated with salt, the special application of forced
circulation crystallizers has been employed for the recovery of the glycerine liquor
and separation of the NaCl salts.
CAUSTIC SODA
The most common process for the manufacture of caustic soda is the electrolysis
of sodium chloride brine. The electrolytic processes produce a caustic soda
solution that has to be concentrated by evaporation. This evaporation process
is difficult since caustic soda solutions have a high boiling point elevation (BPE).
At 50% concentration the BPE is about 80F (45C). This limits the number of
effects usually to three, with the evaporator operated in reverse flow so that the
highest concentration in on the first effect. This effect will typically operate at
over 260F (125C).
An additional problem is that at high temperature, caustic soda solutions corrode
stainless steel. The first and second effect calandrias are usually fabricated in
nickel, which is resistant to corrosion. The third effect can be Avesta 254SLX,
which is far less expensive than nickel. The vapor side of the evaporator can be
304 stainless steel and sometimes carbon steel.
Due to the high temperatures, tubular falling film evaporators are the standard
for this application.
45
12/6/00 11:12 AM Page 46
SOLVENT RECOVERY
Not all evaporation processes are limited to the removal of water. Some
applications require the concentration of a solution of solids and organic solvents.
Organic solvents are frequently used for the extraction of products from raw
materials or fermented broths. The solvent then has to be removed from the
extracted product. A typical application would be the evaporation of acetone
from vegetable oils.
For these types of duties it is necessary to use explosion proof electrical equipment
and intrinsically safe instrumentation. It is also necessary to observe environmental
regulations particularly since some solvents, such as methylene chloride are
classified as regulated compounds with stringent discharge limits to both air and
water. The system must be designed without leaks and with conservation devices
on all possible vents. For evaporator selection, the normal guidelines that are used
for the evaporator of water remain the same. The only major difference is that
HTCs are significantly lower for organic solvents.
A solvent evaporator (Figure 24) is shown below.
Figure 24
46
W
E
A
V
S
A
12/6/00 11:12 AM Page 47
T
P
E
O
As the world has become more concerned about the environment, there has been an
increase in the application of evaporator systems to waste water treatment. These
types of evaporators essentially reduce the volume of the waste by removing and
recovering most of the water in the waste. In some applications, the concentrate
contains product of value, which can be sold or further processed in a dryer to a solid
product. In cases where the product has no value, the concentrate can be dried and
the resulting product buried in a landfill. Since the condensate from these evaporators
is usually quite pure, the water that is recovered can be used as boiler feed, as rinse
fluid for cleaning or merely disposed into the sewer or directly into a river.
As with the processing of any waste product, there are usually severe cost restraints
since, unless forced by regulation, few organizations wish to spend valuable capital
on waste treatment processes. The equipment therefore has to have both low
capital and operating costs.
The key points in the design of a waste water evaporator are:
Flow rate. This is usually quite high for these evaporators.
Solids concentration in the feed. This is usually quite low.
Product concentration and the viscosity of the product at that concentration.
Problems with possible volatile components in the feed.
Corrosive nature of the feed. Since may waste water evaporators have
high concentration ratios, the effects of corrosion can be enhanced in
the final stages of evaporation.
Potential for fouling. This can be very serious in many cases.
Boiling point elevation.
Because of the large duties, mechanical vapor recompression (MVR) evaporation is

usually the choice. However if boiling point elevation is high, the MVR would
be limited to the pre concentration and would require a separate steam powered
single or multi-effect finisher to arrive at the final concentration. The presence of
volatile components in the feed, such as ethanol, can also limit the application of
MVR. In this case, it is usually necessary to remove the volatile components in a
stripper column. In a multi-effect evaporator the stripper column can be placed
between effects, which allows recovery of the heat needed to operate the stripper.
47
12/6/00 11:12 AM Page 48
BREWERY/DISTILLERY EFFLUENTS
The effluents from brewery and distillery plants are often processed with
evaporators to recover the water and produce a concentrated syrup, which can
be sold in liquid form, or added to the spent grains prior to drying. In this case the
solids have value as animal food.
Both MVR and multi-effect evaporators have been used for these types of duty.
Normally falling film tubular calandrias would be used for the pre evaporator
with forced circulation plate or tubular evaporators as the finisher. As in most
applications the viscosity of the product at the evaporation temperature controls
the point at which the material has to be processed in a forced circulation system.
An MVR stillage evaporator (Figure 25) is shown below.
The problem with these applications is that the product, which can be called
stillage, spent wash, spent grains or pot ale, is extremely variable. In particular the
viscosity characteristics of the concentrated liquids depend on the raw material
grain. Waste water produced from plants using corn (maize) as the feed stock are
relatively easy to process. However, waste water from plants which use wheat or
barley as the feedstock will be far more viscous at elevated concentrations.
In some cases, the viscosity characteristics will be so bad that even a forced
circulation evaporator will only be able to concentrate to 35% solids. This usually
means treating the feed with enzymes prior to evaporation so that a solids
concentration of 45% solids can be achieved.
The higher the viscosity, the more
frequently the evaporator will have to
be cleaned. The accepted run time in
the industry is 6 to 8 days. To achieve
this, it is usually necessary to provide
high recirculation around the calandrias
to provide a high wetting rate and
prevent burn on. On the finisher, it is
occasionally necessary to provide
duplex heat exchangers, so that
one can be cleaned while the
other is in operation.
48
Figure 25
12/6/00 11:12 AM Page 49
BLACK LIQUOR
Black liquor is a caustic waste water
generated at paper plants. The quantity
of this material produced is large, and
some of the largest evaporator applications
are with black liquor. An evaporator,
designed by APV, for a feed rate of
170 ton/h (Figure 26), is shown here.
Typically black liquor contains about
3% solids, of which about half is caustic
Figure 26
soda. The presence of this caustic soda

results in quite high boiling point elevation as the concentration increases.
This places some restrictions on the application of MVR, so that most black liquor
evaporators are multi-effect.
This waste water also varies

from plant to plant, and the
concentrate properties are
103
extremely dependent on the

feedstock. The product viscosity
Figure 27) is plotted against
% solids for different types of
102
feedstock. In some cases

in viscosity.
CP
there is a tenfold difference
Figure 27
101
VISCOSITY OF BLACK LIQUORS AT 90C
BAMBOO (KRAFT)
PINE (1)
EUCALYPTUS
(PREHYDROLYSIS KRAFT)
BAGASSE (KRAFT)
BAGASSE (SODA)
STRAW (KRAFT) (3)
NEWTONIAN
NON-NEWTONIAN
100
0.3
10
20
30
40 50
% SOLIDS
60
70
49
12/6/00 11:12 AM Page 50
T U B U L A R
T O
S A N I T A R Y
S T A N D A R D S
Over the last 20 years the capacity for many dairy applications has become
extremely large. The plate evaporator which was primarily designed for hygienic
duties has a maximum capacity of about 60,000 lbs/h (27,000 kg/h). Many
duties in the dairy industry exceed this limit, and therefore it is necessary to use
tubular evaporators.
To meet the processing needs of these large food and dairy cooperatives, the
design and fabrication of tubular evaporators have been brought into compliance
with the legal standards established by various official regulatory groups for
sanitary operations.
The tubular evaporator system consists primarily of three components:
A vertical heating tube bundle which is housed within an insulated

steam jacket or calandria.
A distribution device which allows even liquid flow over the tube
circumference, and therefore prevents 'dry spots' on the heat transfer surface.
A separator to efficiently extract liquid droplets from the vapor stream, and
thereby minimize carry-over of product.
To these are added basic feed tanks, preheaters, duct work, product and CIP
piping, and necessary pumps.
3A DESIGN
While tubular evaporators designed for chemical processing duties generally are
manufactured of carbon or pickled stainless steel, the very nature of the products
handled in the dairy and food fields necessitates the use of highly polished
stainless steel for all product contact surfaces.
The basic evaporator effect, for example, consists of a shell, a top and bottom
tube sheet, and a bundle of 2" diameter seamless seal welded heat transfer tubes
numbering anywhere from 100 to 1600 or more depending upon the
requirements of the evaporation duty. This is topped by a feed distribution system
and a cover or bonnet that clamps to the calandria. Beneath this unit is the
product sump or discharge area and adjacent, the vapor/liquid separator.
50
12/6/00 11:12 AM Page 51
Figure 28
Figure 29
Feed is charged to the system through an inlet at the top of the bonnet and floods
the surface of the distribution system (Figures 28 and 29). As the liquid flows
through many small holes, it spreads evenly across the entire face of the top tube
sheet which is mounted about one inch below and eventually moves into each of
the heat transfer tubes that extend the full height of the calandria.
Since there are many product contact surfaces in this portion of the evaporator (the
inside of the feed inlet piping, both top and bottom of the distribution plate, the
top of the tube sheet, and the interiors of all tubes), the 304 stainless steel used is
polished to a #4/150-180-or-340 grit. APV finishes thus match and very often
exceed 3A standards which call for a surface finish equivalent to 150 grit.
Furthermore, the one inch riser which is added perpendicularly to the tube sheet to
form a product reservoir is fabricated with a minimum 1/4" radius polished fillet
weld. This eliminates any possibility of pockets in which product may collect.
Gaskets sealing the perimeter of both the distribution and tube sheet plates are
made of dairy grade neoprene.
While the evaporator shell normally is fabricated of 304 stainless, polishing is not
required since there are no product contact areas. At the bottom of the evaporator
effect, all areas come in contact with product and, consequently, are of polished
stainless. This includes the underside of the bottom tube sheet, the product sump,
ductwork leading to the adjacent separator and the interior of the separator itself.
When sight glasses, manways, nozzles and light
glasses are added, interior welds are ground and
polished smooth and flush while the components
themselves are mounted at a minimum 3 angle to
allow for proper drainage. Finally, downstream
ductwork between vessels is sloped from 3 to 5
Figure 30
away from the product contact surfaces. In effect, nothing is installed at less than a
90 angle, so that possible product traps are eliminated, and the entire system is
both cleanable and drainable (Figures 30). A further requirement is that the
external surface also be easily cleaned.
51
12/6/00 11:12 AM Page 52
A
N
O
T
R
O
The control of most chemical/industrial evaporator systems is quite simple.

However, with hygienic evaporators the control is somewhat more
complicated due to the need to start up, operate, shut down and then clean
at quite frequent intervals. As a result sophisticated control is more likely to be
needed on hygienic systems.
On almost all evaporation systems there are only two basic objectives:
To concentrate a liquid to a pre-defined solids content.

To process a pre-defined feed rate of raw material.
Theoretically this can be achieved with only two control loops. However in
practice there are additional loops for level control and pressure control.
Product concentration has been measured using refractive index, density and
viscosity techniques. Over the last ten years, the use of mass flow meters for
density measurement has become the standard. A typical instrument is the Foxboro
I/A Series, CFS10. This type of meter provides an accurate measurement (usually
out to the 4th decimal place) of both flow and density. The density measurement,
which is easily converted to a solids content, can then be used to control either
product removal rate from the evaporator, steam flow, or feed flow.
There are two techniques used to control evaporators, and the choice is based on
the design of the evaporator. In applications where liquid recirculation is required
to maintain sufficient wetting in the final stage of the evaporator, the product
concentration control is simple and accurate. The procedure is to set the steam
flow rate at the design value, remove product based on density in the recirculation
loop, and adjust the feed flow to maintain liquid levels in the evaporator. When a
higher throughput is required, then the steam rate is increased. This technique
provides excellent control of the product concentration with conventional analog
controllers.
52
12/6/00 11:12 AM Page 53
For heat sensitive products, it is best to avoid recirculation whenever possible. In

the case of once-through-flow in the final stage, there is no recirculation loop in
which to install the transmitter and to delay discharge of product when not on
specification. In this case, the method is to set the feed flow rate to the desired
value and then change the energy input to produce the product concentration
required. The energy input may be the steam rate or the power into the MVR. This
technique does not control product quality particularly accurately, since response is
slow. However it is satisfactory for most purposes, and the user can always apply
more sophisticated PLC control when necessary. For extremely accurate control,
the predictive control system Connoisseur by Foxboro is recommended.
Almost all evaporators will have to be cleaned at some time. Some chemical
evaporators may run for months between cleaning cycle. Also with non-hygienic
duties, the only requirement is to clean the heat transfer surface sufficiently to
restore design performance.
In the case of hygienic evaporators, the concern is not only plant operation,
but also contamination from bacteria. Typically, a hygienic evaporator will be
cleaned every day.
Dairy evaporators, which are designed and constructed to 3A standards, are
subject to one of the highest cleaning standards. The inspector will expect
that the equipment be cleaned completely with no residue left on any surfaces.
The potential labor costs to start up, shut down and go through a complex
cleaning cycle, on a daily basis, are very high. A fully automatic system is
therefore required to perform all these operations. These functions are ideally
performed by a PLC.
Usually PLC control offers maximum throughput, maximum efficiency, constant
product, and minimizes startup and shutdown times. It also minimizes C.I.P. time
while maximizing C.I.P. effectiveness. Most PLCs offer historical data collection
so that management can continue to improve and maximize the evaporator
systems performance.
53
12/6/00 11:12 AM Page 54
E
A
L
R
Almost all small evaporators and certain medium size evaporators can be
preassembled in the shop prior to shipment. The advantages of this approach
are given below:
Assembly of equipment, piping and wiring in the shop is easier and

less expensive than assembly in the field.
The time to install the equipment in the field is considerably reduced.

This reduces the disruption to other plant operation.
The overall cost of the project is reduced.
A small preassembled Paravap evaporator (Figure 31) can be fully assembled on

a stainless steel skid complete with control panel and motor starters. The on site
installation takes hours rather than days.
A larger system (Figure 32), like this double effect Paraflash system, was too large
to ship as a single skid so it was assembled of two skids in the shop and partially
broken down for shipment.
The maximum size of equipment that can be shipped over the roads is about
12ft (3.65m) by 14ft (4.25m) by 100ft (30m). However, it is still possible to
preassemble large systems in the shop. The systems are then match marked and
disassembled for shipment. Assembly on site is a relatively simple procedure.
However, preassembly becomes less attractive economically as the size of the
systems increases.
Figure 31
54
Figure 32
T H E
12/6/00 11:13 AM Page 55
P R O D U C T I O N
H I G H
Q U A L I T Y
O F
J U I C E
C O N C E N T R A T E S
Changes in our lifestyles over the past twenty years have been dramatic. Not the
least of these changes has been our dietary habits influenced not only by our
perceived values of diet related to general health, but also by changes in food
processing technology across a very wide spectrum.
Storage of fruit before processing begins a gradual process of change from the
fresh product. Breaking or peeling of fruit releases some of the natural essences
even at atmospheric temperatures, and natural biochemical processes commence
which affect color and enzyme components, pectin and other characteristic
properties of the fruit.
The aim of food manufacturers is to produce a juice or concentrate which closely
resembles the original fresh from the fruit. Of all the ways we can influence this,
time and temperature are paramount.
EVAPORATION
Evaporation is by far the most prevalent process used for the production of
concentrates. It provides a highly energy efficient means of removing water
and is well suited to recovering essence components during the process.
The problem for the equipment designer has always been one of providing a
cost-effective system having low energy requirements, with acceptable concentrate
quality, and along the way collecting essences in sufficiently useable quantity
and quality.
The ultra short time FFPE (Falling Film Plate Evaporator) was introduced by
APV in the early 1970s. The patent covered a two-plate per unit design one
steam and one product in which the product could be fed first to one half of
the plate then returned in series to the other side of the plate for improved
wetting without recirculation.
55
12/6/00 11:13 AM Page 56
The most difficult design area of any falling film evaporator is the liquid distribution
system which ensures an even flow of liquid over the total evaporating surface.
This was achieved by an ingenious three stage process involving small pressure
losses and flash vapor.
Time/temperature are markedly influenced by single pass operation in an
evaporator by avoiding the use of recirculation. In the FFPE, with its two-stage
design and longer flow path, recirculation is avoided on all triple effect and over
systems, and even on double-effect under some temperature conditions.
This design could still be improved, however, and the FFLE (Falling Film Long
Evaporator) is the current development in the plate evaporator technology. This is
a divided plate design like the FFPE, but has a 50% longer flow path. This creates
thinner films off the plate, with improved wetting characteristics. A single falling film
plate effect, less than 78"/2 meters in plate length, is equivalent to one pass in a
tube 630"/16 meters long.
A special arrangement of the support pipes improves cleaning in place (CIP)
of the plate, by using a disparate positioning on the plate. The FFLE is current
state-of-the art technology, producing concentrates of high quality on a wide
range of juices.
ESSENCE RECOVERY
Distillation
Essences can be recovered by full distillation techniques with high yield on
products less sensitive to temperature, such as apple and grape. The distillation
aroma recovery process is described in the following case study, where its
application in a special configuration on grape juice concentration combines a
number of new technological features.
Partial Condensation
The loss of, or damage to, essences from fruit commences at the moment
of picking. It increases after extraction, and with any form of heating and
flash vapor release. The partial condensation aroma recovery unit has
provided effective and economic ways of capturing the elusive flavor
components for storage and re-use with reconstituted juices or for use in the
cosmetic and other industries.
56
12/6/00 11:13 AM Page 57
The partial condensation aroma recovery unit makes use of the fact that if juice is
heated in a closed system, then released into a region of pressure below the
saturation point, flash vapors released will strip aroma compounds from the liquid
phase into volatiles which travel with the vapors. There will be some essence
components which do not volatalize and remain in the juice throughout the
process, but a substantial percentage of the aromas is liberated.
If the vapors from the first strip are withdrawn from the first stage of evaporation
in a multi-effect system, they will be more than enough in quantity to ensure a high
percentage recovery of aromas. These will go with the vapor to the heating side
of the next evaporator effect to provide the energy for further evaporation. In the
process, only part of the vapor is condensed. A portion, perhaps 10 or 15%, is
allowed to pass through the heating side uncondensed, and then ducted to the
aroma recovery system.
Because of the different boiling points of aroma compounds, most of the essences
remain with the uncondensed portion. In the aroma recovery unit, a further
selective condensing process takes place, which removes more of the water vapor
to leave a concentrated essence. This essence is chilled and collected together
with recovered components from a final vent scrubber system. It can then be
stored for later use or added back to aseptically processed concentrate during
the cooling stage.
The temperature at which the first strip takes place varies according to the fruit.
Some tropical fruits, like pineapple, are move sensitive, and temperatures above
60C should be avoided. For apple and less sensitive fruits, temperatures in the
80s or 90s can provide higher yields without thermal degradation of the essence.
CASE STUDY
Concord grape presents its own special problems in concentration due to the
high level of tartrates. These tartrates can crystallize out under certain temperature
and concentration conditions with unhappy results in terms of length of run
between cleanings.
57
12/6/00 11:13 AM Page 58
A team of distillation and evaporation specialists used new and existing

technology to develop a system to cope with these product characteristics and to
produce quality essences with high yield. The key features of the final solution
chosen were as follows:
In order to keep temperatures above crystallization, the grape juice was

concentrated using a reverse feed design, with dilute juice being directed
to the low temperature effect first and leaving at the high temperature
effect (Figure 33).
In order to provide the quality enhancement and color benefits specified,

an FFLE was selected in a three, four or five (Welchs) effect configuration.
This ensured the shortest possible residence time during the initial stages of
concentration, where tartrate crystallization can be more readily controlled.
A tubular finisher evaporator was selected, designed specifically to deal

with the problem area where concentrate is approaching the supersaturation
point for tartrates.
Figure 33. Flow diagram. Concord grape juice is extremely difficult to process due to the
precipitation of tartrates during concentration. To keep temperatures above crystallization,
as the grape juice is concentrated, a reverse feed design was selected, with dilute juice
being directed to the low temperature effect first and leaving at the high temperature effect.
58
12/6/00 11:13 AM Page 59
At the finisher level of concentration, it was no longer possible to operate at

temperatures high enough to keep tartrates in solution. The designer therefore used
the relatively larger effective diameter of a tube to advantage, by employing a
forced circulation mode operating at only 120F (50C). This technique promoted
larger crystal growth in the final concentrate. Tartrate crystal growth occurs more
on crystals in suspension instead of on equipment. This promotes longer runs
between cleaning. The forced circulation tubular design was well able to cope
with the crystals on extended operating times, and the larger crystals were much
easier to deal with at the separation stage.
A large distillation column was chosen to recover essences from the grape juice.
In the reverse feed system, most of the highly volatile essence components (methyl
anthranilate being the key essence) were released in the initial stage of
evaporation. When these condensates plus vents were taken into the column
for stripping and rectification, a high yield of essence was guaranteed.
The key to the design was the use of essence-rich vapor discharge from
the distillation column, directly into the steam side of the first effect FFLE,
where it provided the total energy to drive the three- or four- effect
preconcentrator evaporator using the evaporator as a condenser.
The first effect condensate
now became the rich essence,
and most of this was returned to
the column as reflux. A small
quantity of essence was removed
and chilled, and later this was
added back to the concentrate
for quality enhancement.
In terms of energy efficiency,
this plant (Figure 34) was a
breakthrough in design of high
quality concentrate-plusessence systems.
Figure 34
59
12/6/00 11:13 AM Page 60
TO CONVERT FROM
E
R
I
O
N
N
G
S
TO
MULTIPLY BY
Calories/(Gram) (Mole) (C)
Molecular
BTU/(Pound) (F)
1.0
Pounds/Gallon
Pounds/Cubic Ft.
8.33
62.42
Btu/(Hr) (Ft) (F)
0.6719
0.5778
Centipoise
Specific Gravity
Centipoise
1488.2
Centistokes
100
psi
0.14504
14.504
0.4912
14.696
0.01908
0.01908
Heat Capacity
Calories/(Gram) (C)
Weight
Density
Gram/Milliliter
Thermal Conductivity
Kilocalorie/(Hr) (m) (C)
Watt/(m) (C)
Viscosity
Centistokes
Dynamic Viscosity
Pound-Mass/(Ft) (Sec)
Kinematic Viscosity
Cm2/Sec
Pressure
KiloPascal
Bar
Inches Hg Absolute
Atmosphere
Torr
mm Hg
psia
Enthalpy
Calorie/Gram
Work/Energy
(Kilowatt) (Hr)
(Horsepower) (Hr)
Calorie
Btu/Pound-Mass
1.8
Btu
3412.1
2544.4
0.003968
Btu/(Hr)(Ft2)((F)
0.2048
1761.1
Heat Transfer Coefficient

Kilocalorie/(Hr) (M2) (C)
Watt/(cm2)(C)
60
12/6/00 11:13 AM Page 61
P R O P E R T I E S
S A T U R A T E D
O F
S T E A M
T E M P E R A T U R E
TEMPERATURE
PRESSURE
VACUUM
T A B L E S
SPECIFIC VOLUME LATENT HEAT

Ft3/lb
m3/Kg
0.08859 0.00611 29.741 755.421

0.09223 0.00636 29.734 755.244
0.09600 0.00662 20.726 526.440
3304.7
3180.7
3061.9
206.544
198.794
191.369
1075.5
1074.9
1074.4
597.5
597.2
596.9
1.667
2.222
2.778
3.333
3.889
0.09991
0.10395
0.01815
0.11249
0.11698
0.00689
0.00717
0.00125
0.00776
0.00807
29.718
29.710
29.701
29.692
20.683
754.837
754.634
754.405
754.177
525.348
2948.1
2839.0
2734.4
2634.2
2538.0
184.256
177.438
170.900
164.638
158.625
1073.8
1073.2
1072.7
1072.1
1071.5
596.6
596.2
595.9
595.6
595.3
40
41
42
43
44
4.444
5.000
5.556
6.111
6.667
0.12163
0.12645
0.13143
0.13659
0.14192
0.00839
0.00872
0.00906
0.00942
0.00979
29.674
29.664
29.654
29.643
29.632
753.720
753.466
753.212
752.932
752.653
2445.8
2357.3
2274.4
2191.0
2112.8
152.863
147.331
142.150
136.938
132.050
1071.0
1070.4
1069.8
1069.3
1068.7
595.0
594.7
594.3
594.1
593.7
45
46
47
48
49
7.222
7.778
8.333
8.889
9.444
0.14744
0.15314
0.15904
0.16514
0.17144
0.01017
0.01056
0.01097
0.01139
0.01182
29.621
29.610
29.597
29.585
29.572
752.373
752.094
751.764
751.459
751.129
2037.8
1965.7
1896.5
1830.0
1766.2
127.363
122.856
118.531
114.375
110.388
1068.1
1067.6
1067.0
1066.4
1065.9
593.4
593.1
592.8
592.4
592.2
50
51
52
53
54
10.000
10.556
11.111
11.667
12.222
0.17796
0.18469
0.19165
0.19883
0.20625
0.01227
0.01274
0.01322
0.01371
0.01422
29.559
29.545
29.531
29.516
29.501
750.799
750.443
750.087
749.706
749.325
1704.8
1645.9
1589.2
1534.8
1482.4
106.550
102.869
99.325
95.925
92.650
1065.3
1064.7
1064.2
1063.6
1063.1
591.8
591.5
591.2
590.9
590.6
55
56
57
58
59
12.778
13.333
13.889
14.444
15.000
0.21392
0.22183
0.23000
0.23843
0.24713
0.01475
0.01530
0.01586
0.01644
0.01704
29.486
29.470
29.453
29.436
29.418
748.944
748.538
748.106
747.674
747.217
1432.0
1383.6
1337.0
1292.2
1249.1
89.500
86.475
83.563
80.763
78.069
1062.5
1061.9
1061.4
1060.8
1060.2
590.3
589.9
589.7
589.3
589.0
60
61
62
63
64
15.556
16.111
16.667
17.222
17.778
0.25611
0.26538
0.27494
0.28480
0.29497
0.01766
0.01830
0.01896
0.01964
0.02034
29.400
29.381
29.362
29.341
29.321
746.760
746.277
745.795
745.261
744.753
1207.6
1167.6
1129.2
1092.1
1056.5
75.475
72.975
70.575
68.256
66.031
1059.7
1059.1
1058.5
1058.0
1057.4
588.7
588.4
588.1
587.8
587.4
32
33
34
0.000
0.556
1.111
35
36
37
38
39
PSIA
BAR
In Hg
mm Hg
Btu/lb Kcals/Kg
61
TEMPERATURE
62
12/6/00 11:13 AM Page 62
PRESSURE
VACUUM
PSIA
BAR
In Hg
mm Hg
Ft3/lb
m3/Kg
Btu/lb Kcals/Kg
65
66
67
68
69
18.333
18.889
19.444
20.000
20.556
0.30545
0.31626
0.32740
0.33889
0.35073
0.02107
0.02181
0.02258
0.02337
0.02419
29.299
29.277
29.255
29.231
29.207
2.02062
2.01910
2.01759
2.01593
2.01428
1022.1
989.0
957.2
926.5
896.9
63.881
61.813
59.825
57.906
56.056
1056.9
1056.3
1055.7
1055.2
1054.6
587.2
586.8
586.5
586.2
585.9
70
71
72
73
74
21.111
21.667
22.222
22.778
23.333
0.36292
0.37549
0.38844
0.40177
0.41550
0.02503
0.02590
0.02679
0.02771
0.02866
29.182
29.157
29.130
29.103
29.075
2.01255
2.01083
2.00897
2.00710
2.00517
868.4
840.9
814.3
788.8
764.1
54.275
52.556
50.894
49.300
47.756
1054.0
1053.5
1052.9
1052.4
1051.8
585.6
585.3
584.9
584.7
584.3
75
76
77
78
79
23.889
24.444
25.000
25.556
26.111
0.42964
0.44420
0.45919
0.47461
0.49049
0.02963
0.03063
0.03167
0.03273
0.03383
29.027
29.017
28.986
28.955
28.923
2.00186
2.00117
1.99903
1.99690
1.99469
740.3
717.4
695.2
673.9
653.2
46.269
44.838
43.450
42.119
40.825
1051.2
1050.7
1050.1
1049.5
1049.0
584.0
583.7
583.4
583.1
582.8
80
81
82
83
84
26.667
27.222
27.778
28.333
28.889
0.50683
0.52364
0.54093
0.55872
0.57702
0.03495
0.03611
0.03731
0.03853
0.03979
28.889
28.855
28.820
28.784
28.746
1.99234
1.99000
1.98759
1.98510
1.98248
633.3
614.1
595.6
577.6
560.3
39.581
38.381
37.225
36.100
35.019
1048.3
1047.8
1047.3
1046.7
1046.1
582.4
582.1
581.8
581.5
581.2
85
86
87
88
89
29.444
30.000
30.556
31.111
31.667
0.59583
0.61518
0.63507
0.65551
0.67653
0.04109
0.04243
0.04380
0.04521
0.04666
28.708
28.669
28.628
28.587
28.544
1.97986
1.97717
1.97434
1.97152
1.96855
543.6
527.5
511.9
496.8
432.2
33.975
32.969
31.994
31.050
27.013
1045.6
1045.0
1044.4
1043.9
1043.3
580.9
580.6
580.2
579.9
579.6
90
91
92
93
94
32.222
32.778
33.333
33.889
34.444
0.69813
0.72032
0.74313
0.76655
0.79062
0.04815
0.04968
0.05125
0.05287
0.05453
28.500
28.455
28.408
28.361
28.312
1.96552
1.96241
1.95917
1.95593
1.95255
468.1
454.5
441.3
428.6
416.3
29.256
28.406
27.581
26.788
26.019
1042.7
1042.2
1041.6
1041.0
1040.5
579.3
579.0
578.7
578.3
578.1
95
96
97
98
99
35.000
35.556
36.111
36.667
37.222
0.81534
0.84072
0.86679
0.89356
0.92103
0.05623
0.05798
0.05978
0.06162
0.06352
28.261
28.210
28.157
28.102
28.046
1.94903
1.94552
1.94186
1.93807
1.93421
404.4
392.9
381.7
370.9
360.5
25.275
24.556
23.856
23.181
22.531
1039.9
1039.3
1038.8
1038.2
1037.6
577.7
577.4
577.1
576.8
576.4
TEMPERATURE
12/6/00 11:13 AM Page 63
PRESSURE
VACUUM
PSIA
BAR
In Hg
mm Hg
Ft3/lb
m3/Kg
Btu/lb Kcals/Kg
100
101
102
103
104
37.778
38.333
38.889
39.444
40.000
0.94924
0.97818
1.00789
1.03838
1.06965
0.06546
0.06746
0.06951
0.07161
0.07377
27.989
27.930
27.869
27.807
27.743
1.93028
1.92621
1.92200
1.91772
1.91331
350.4
340.6
331.1
322.0
313.1
21.900
21.288
20.694
20.125
19.569
1037.1
1036.5
1035.9
1035.4
1034.8
576.2
575.8
575.5
575.2
574.9
105
106
107
108
109
40.556
41.111
41.667
42.222
42.778
1.10174
1.1347
1.1684
1.2030
1.2385
0.07598
0.07826
0.08058
0.08297
0.08541
27.678
27.611
27.542
27.417
27.400
1.90883
1.90421
1.89945
1.89083
1.88966
304.5
296.18
288.11
280.30
272.72
19.031
18.511
18.007
17.519
17.045
1034.2
1033.6
1033.1
1032.5
1031.9
574.6
574.2
573.9
573.6
573.3
110
111
112
113
114
43.333
43.889
44.444
45.000
45.556
1.2750
1.3123
1.3505
1.3898
1.4299
0.08793
0.09050
0.09314
0.09585
0.09861
27.325
27.249
27.172
27.092
27.001
1.88448
1.87924
1.87393
1.86841
1.86214
265.39
258.28
251.38
244.70
238.22
16.587
16.143
15.711
15.294
14.889
1031.4
1030.8
1030.2
1029.6
1029.1
573.0
572.7
572.3
572.0
571.7
115
116
117
118
119
46.111
46.667
47.222
47.778
48.333
1.4711
1.5133
1.5566
1.6009
1.6463
0.10146
0.10437
0.10735
0.11041
0.11354
26.926
26.840
26.752
26.662
26.569
1.85697
1.85103
1.84497
1.83876
1.83234
231.94
225.85
219.94
214.21
208.66
14.496
14.116
13.746
13.388
13.041
1028.5
1027.9
1027.3
1026.8
1026.2
571.4
571.1
570.7
570.4
570.1
120
121
122
123
124
48.889
49.444
50.000
50.556
51.111
1.6927
1.7403
1.7891
1.8390
1.8901
0.11674
0.12002
0.12339
0.12683
0.13035
26.475
26.378
26.279
26.177
26.073
1.82586
1.81917
1.81234
1.80531
1.79814
203.26
198.03
192.95
188.03
183.24
12.704
12.377
12.059
11.752
11.453
1025.6
1025.0
1024.5
1023.9
1023.3
569.8
569.4
569.2
568.8
568.5
125
126
127
128
129
51.667
52.222
52.778
53.333
53.889
1.9428
1.9959
2.0507
2.1068
2.1642
0.13399
0.13765
0.14143
0.14530
0.14926
25.966
25.858
25.746
25.632
25.515
1.79076
1.78331
1.77559
1.76772
1.75966
178.60
174.09
169.72
165.47
161.34
11.163
10.881
10.608
10.342
10.084
1022.7
1022.2
1021.6
1021.0
1020.4
568.2
567.9
567.6
567.2
566.9
130
131
132
133
134
54.444
55.000
55.556
56.111
56.667
2.2230
2.2830
2.3445
2.4074
2.4717
0.15331
0.15745
0.16169
0.16603
0.17046
25.395
25.273
25.148
25.020
24.889
1.75138
1.74297
1.73434
1.72552
1.71648
157.33
153.44
149.66
145.98
142.41
9.833
9.590
9.354
9.124
8.901
1019.8
1019.3
1018.7
1018.1
1017.5
566.6
566.3
565.9
565.6
565.3
63
TEMPERATURE
64
12/6/00 11:13 AM Page 64
PRESSURE
VACUUM
PSIA
BAR
In Hg
mm Hg
Ft3/lb
m3/Kg
Btu/lb Kcals/Kg
135
136
137
138
139
57.222
57.778
58.333
58.889
59.444
2.5375
2.6047
2.6735
2.7438
2.8157
0.17500
0.17963
0.18438
0.18923
0.19419
27.678
27.611
27.542
27.417
27.400
1.90883
1.90421
1.89945
1.89083
1.88966
304.50
296.18
288.11
280.30
272.72
19.031
18.511
18.007
17.519
17.045
1034.2
1033.6
1033.1
1032.5
1031.9
574.6
574.2
573.9
573.6
573.3
140
141
142
143
144
60.000
60.556
61.111
61.667
62.222
2.8892
2.9643
3.0411
3.1195
3.1997
0.19926
0.20443
0.20973
0.21514
0.22067
27.325
27.249
27.172
27.092
27.001
1.88448
1.87924
1.87393
1.86841
1.86214
265.39
258.28
251.38
244.70
238.22
16.587
16.143
15.711
15.294
14.889
1031.4
1030.8
1030.2
1029.6
1029.1
573.0
572.7
572.3
572.0
571.7
145
146
147
148
149
62.778
63.333
63.889
64.444
65.000
3.2816
3.3653
3.4508
3.5381
3.6273
0.22632
0.23209
0.23799
0.24401
0.25016
26.926
26.840
26.752
26.662
26.569
1.85697
1.85103
1.84497
1.83876
1.83234
231.94
225.85
219.94
214.21
208.66
14.496
14.116
13.746
13.388
13.041
1028.5
1027.9
1027.3
1026.8
1026.2
571.4
571.1
570.7
570.4
570.1
150
151
152
153
154
65.556
66.111
66.667
67.222
67.778
3.7184
3.8114
3.9065
4.0035
4.1025
0.25644
0.26286
0.26941
0.27610
0.28293
26.475
26.378
26.279
26.177
26.073
1.82586
1.81917
1.81234
1.80531
1.79814
203.26
198.03
192.95
188.03
183.24
12.704
12.377
12.059
11.752
11.453
1025.6
1025.0
1024.5
1023.9
1023.3
569.8
569.4
569.2
568.8
568.5
155
156
157
158
159
68.333
68.889
69.444
70.000
70.556
4.2036
4.3068
4.4122
4.5197
4.6294
0.28990
0.29702
0.30429
0.31170
0.31927
25.966
25.858
25.746
25.632
25.515
1.79076
1.78331
1.77559
1.76772
1.75966
178.60
174.09
169.72
165.47
161.34
11.163
10.881
10.608
10.342
10.084
1022.7
1022.2
1021.6
1021.0
1020.4
568.2
567.9
567.6
567.2
566.9
160
161
162
163
164
71.111
71.667
72.222
72.778
73.333
4.7414
4.8556
4.9722
5.0911
5.2124
0.32699
0.33487
0.34291
0.35111
0.35948
25.395
25.273
25.148
25.020
24.889
1.75138
1.74297
1.73434
1.72552
1.71648
157.33
153.44
149.66
145.98
142.41
9.833
9.590
9.354
9.124
8.901
1019.8
1019.3
1018.7
1018.1
1017.5
566.6
566.3
565.9
565.6
565.3
165
166
167
168
169
73.889
74.444
75.000
75.556
76.111
5.3361
5.4623
5.5911
5.7223
5.8562
0.36801
0.37671
0.38559
0.39464
0.40388
24.755
24.618
24.478
24.335
24.188
1.70724
1.69779
1.68814
1.67828
1.66814
138.94
135.57
132.29
129.11
126.01
8.684
8.473
8.268
8.069
7.876
1016.9
1016.4
1015.8
1015.2
1014.6
564.9
564.7
564.3
564.0
563.7
TEMPERATURE
12/6/00 11:13 AM Page 65
PRESSURE
VACUUM
PSIA
BAR
In Hg
mm Hg
Ft3/lb
m3/Kg
Btu/lb Kcals/Kg
170
171
172
173
174
76.667
77.222
77.778
78.333
78.889
5.9926
6.1318
6.2736
6.4182
6.5656
0.41328
0.42288
0.43266
0.44263
0.45280
17.720
17.437
17.148
16.854
16.554
1.22207
1.20255
1.18262
1.16234
1.14166
62.06
60.74
59.45
58.19
56.97
3.879
3.796
3.716
3.637
3.561
996.2
998.6
998.0
997.4
996.8
553.4
554.8
554.4
554.1
553.8
175
176
177
178
179
79.444
80.000
80.556
81.111
81.667
6.7159
6.8690
7.0250
7.1840
7.3460
0.46317
0.47372
0.48448
0.49545
0.50662
16.248
15.936
15.618
15.295
14.965
1.12055
1.09903
1.07710
1.05483
1.03207
55.77
54.61
53.47
52.36
51.28
3.486
3.413
3.342
3.273
3.205
996.2
995.6
995.0
994.4
993.8
553.4
553.1
552.8
552.4
552.1
180
181
182
183
184
82.222
82.778
83.333
83.889
84.444
7.5110
7.679
7.850
8.025
8.203
0.51800
0.52959
0.54138
0.55345
0.56572
14.629
14.287
13.939
13.582
13.220
1.00890
0.98531
0.96131
0.93669
0.91172
50.225
49.194
48.189
47.207
46.249
3.139
3.075
3.012
2.950
2.891
993.2
992.6
992.0
991.4
990.8
551.8
551.4
551.1
550.8
550.4
185
186
187
188
189
85.000
85.556
86.111
86.667
87.222
8.384
8.568
8.756
8.947
9.141
0.57821
0.59090
0.60386
0.61703
0.63041
12.851
12.477
12.094
11.705
11.310
0.88628
0.86048
0.83407
0.80724
0.78000
45.313
44.400
43.508
42.638
41.787
2.832
2.775
2.719
2.665
2.612
990.2
989.6
989.0
988.4
987.8
550.1
549.8
549.4
549.1
548.8
190
191
192
193
194
87.778
88.333
88.889
89.444
90.000
9.340
9.541
9.747
9.956
0.168
0.64414 10.905 0.75207

0.65800 10.496 0.72386
0.67221 10.076 0.69490
0.68662 9.651 0.66559
0.70124 9.219 0.63579
40.957
40.146
39.354
38.580
37.824
2.560
2.509
2.460
2.411
2.364
987.1
986.5
985.9
985.3
984.7
548.4
548.1
547.7
547.4
547.1
195
196
197
198
199
90.556
91.111
91.667
92.222
92.778
10.385
10.605
10.830
11.058
11.290
0.71621
0.73138
0.74690
0.76262
0.77862
8.777
8.329
7.871
7.407
6.935
0.60531
0.57441
0.54283
0.51083
0.47828
37.086
36.364
35.659
34.970
34.297
2.318
2.273
2.229
2.186
2.144
984.1
983.5
982.8
982.2
981.6
546.7
546.4
546.0
545.7
545.3
200
201
202
203
204
93.333
93.889
94.444
95.000
95.556
11.526
11.766
12.011
12.259
12.512
0.79490
0.81145
0.82834
0.84545
0.86290
6.454
5.966
5.467
4.962
4.447
0.44510
0.41145
0.37703
0.34221
0.30669
33.639
32.996
32.367
31.752
31.151
2.102
2.062
2.023
1.985
1.947
981.0
980.4
979.7
979.1
978.5
545.0
544.7
544.3
543.9
543.6
65
TEMPERATURE
66
12/6/00 11:13 AM Page 66
PRESSURE
VACUUM
PSIA
BAR
In Hg
mm Hg
Ft3/lb
m3/Kg
Btu/lb Kcals/Kg
205
206
207
208
209
96.111
96.667
97.222
97.778
98.333
12.770
13.031
36.235
36.543
36.852
0.88069
0.89869
2.49894
2.52022
2.54151
0.06074
0.06198
0.17234
0.17381
0.17528
0.00419
0.00427
0.01189
0.01199
0.01209
30.564
29.989
29.428
28.878
28.341
1.910
1.874
1.839
1.805
1.771
974.7
974.1
973.5
972.8
972.2
541.5
541.2
540.8
540.4
540.1
210
211
212
98.889
99.444
100.000
37.160
37.469
37.778
2.56279 0.17674 0.01219

2.58408 0.17821 0.01229
2.60536 0.17968 0.01239
27.816
27.302
26.799
1.739
1.706
1.675
971.6
970.9
970.3
539.8
539.4
539.1
212
213
214
215
216
100.000
100.556
101.111
101.667
102.222
37.778
38.086
38.395
38.704
39.012
2.60536
2.62665
2.64794
2.66922
2.69051
26.799
26.307
25.826
25.355
24.894
1.675
1.644
1.614
1.585
1.556
970.3
969.7
969.0
968.4
967.8
539.1
538.7
538.3
538.0
537.7
220
224
228
232
236
104.444
106.667
108.889
111.111
113.333
40.247
41.481
42.716
43.951
45.185
2.77565
2.86079
2.94593
3.03108
3.11622
23.148
21.545
20.037
18.718
17.471
1.447
1.347
1.252
1.170
1.092
965.2
962.6
960.0
957.4
954.8
536.2
534.8
533.3
531.9
530.4
240
244
248
252
256
115.556
117.778
120.000
122.222
124.444
46.420
47.654
48.889
50.123
51.358
3.20136
3.28650
3.37165
3.45679
3.54193
16.321
15.260
14.281
13.375
12.538
1.020
0.954
0.893
0.836
0.784
952.1
949.5
946.8
944.1
941.4
528.9
527.5
526.0
524.5
523.0
260
264
268
272
276
126.667
128.889
131.111
133.333
135.556
52.593
53.827
55.062
56.296
57.531
3.62708
3.71222
3.79736
3.88250
3.96765
11.762
11.042
10.375
9.755
9.180
0.735
0.690
0.648
0.610
0.574
938.6
935.9
933.1
930.3
927.5
521.4
519.9
518.4
516.8
515.3
280
284
288
292
296
137.778
140.000
142.222
144.444
146.667
58.765
60.000
61.235
62.469
63.704
4.05279
4.13793
4.22307
4.30822
4.39336
8.6439
8.1453
7.6807
7.2475
6.8433
0.540
0.509
0.480
0.453
0.428
924.6
921.7
918.8
915.9
913.0
513.7
512.1
510.4
508.8
507.2
TEMPERATURE
12/6/00 11:13 AM Page 67
PRESSURE
VACUUM

Ft3/lb
m3/Kg
Btu/lb Kcals/Kg
4.62103
4.90476
5.20228
5.51400
5.83917
6.4658
6.1130
5.7830
5.4742
5.1849
0.404
0.382
0.361
0.342
0.324
910.0
907.0
904.0
901.0
897.9
505.6
503.9
502.2
500.6
498.8
89.643
94.826
100.245
105.907
111.820
6.18228
6.53972
6.91345
7.30393
7.71172
4.9138
4.6595
4.4208
4.1966
3.9859
0.307
0.291
0.276
0.262
0.249
894.8
891.6
888.5
885.3
882.1
497.1
495.3
493.6
491.8
490.1
171.111
173.333
175.556
177.778
180.000
117.992
124.430
131.142
138.138
145.424
8.13738
8.58138
9.04428
9.52676
10.02924
3.7878
3.6013
3.4258
3.2603
3.1044
0.237
0.225
0.214
0.204
0.194
878.8
875.5
872.2
868.9
865.5
488.2
486.4
484.6
482.7
480.8
360
364
368
372
376
182.222
184.444
186.667
188.889
191.111
153.010
160.903
169.113
177.648
186.517
10.55241
11.09676
11.66297
12.25159
12.86324
2.9573
2.8184
2.6873
2.5633
2.4462
0.185
0.176
0.168
0.160
0.153
862.1
858.6
855.1
851.6
848.1
478.9
477.0
475.1
473.1
471.2
380
384
388
392
396
193.333
195.556
197.778
200.000
202.222
195.729
205.294
215.220
225.516
236.193
13.49855
14.15821
14.84276
15.55283
16.28917
2.3353
2.2304
2.1311
2.0369
1.9477
0.146
0.139
0.133
0.127
0.122
844.5
840.8
837.2
833.4
829.7
469.2
467.1
465.1
463.0
460.9
PSIA
BAR
300
304
308
312
316
148.889
151.111
153.333
155.556
157.778
67.005
71.119
75.433
79.953
84.668
320
324
328
332
336
160.000
162.222
164.444
166.667
168.889
340
344
348
352
356
In Hg
mm Hg
67

Apv - Evaporator Handbook

Uploaded by

Copyright:

Available Formats

Apv - Evaporator Handbook

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Apv - Evaporator Handbook

Uploaded by

Copyright:

Available Formats

What are the different types of evaporators described in the document?

What are the different types of evaporators described in the document?

What are some factors that influence evaporator design?

What are some factors that influence evaporator design?

APV Evaporator Hndbook

12/6/00 11:07 AM Page 2

APV Evaporator Hndbook

12/6/00 11:07 AM Page 3

APV Evaporator Hndbook

12/6/00 11:07 AM Page 4

TYPES AND DESIGN

Rising film tubular

Falling film tubular

Rising/falling film tubular

APV Evaporator Hndbook

12/6/00 11:07 AM Page 5

APV Evaporator Hndbook

12/6/00 11:07 AM Page 6

Evaporation by natural circulation is

RISING FILM TUBULAR

APV Evaporator Hndbook

12/6/00 11:07 AM Page 7

FALLING FILM TUBULAR

example, if steam is available at

(49C); the total available

of 25F (14C). However,

as many as 10 or more effects.

APV Evaporator Hndbook

12/6/00 11:07 AM Page 8

RISING/FALLING FILM TUBULAR

(Figure 5) has the advantages

is approximately half the height

positioned at the bottom of

APV Evaporator Hndbook

12/6/00 11:07 AM Page 9

CIRCULATION PUMP GIVING

APV Evaporator Hndbook

12/6/00 11:07 AM Page 10

PLATE TYPE EVAPORATORS

These APV plate evaporation systems are made in four arrangements

APV Evaporator Hndbook

12/6/00 11:07 AM Page 11

Low alcohol beer

RISING/FALLING FILM PLATE

APV Evaporator Hndbook

12/6/00 11:07 AM Page 12

APV Evaporator Hndbook

12/6/00 11:07 AM Page 13

The plate evaporator is designed to operate at pressures extending from

Require operating temperatures between 80-212F (26 to 100C)

Have a capacity range of 1000-35,000 lbs/hr

Have a need for future capacity increase since evaporator capabilities

Require the evaporator to be installed in an area that has limited

Where product quality demands a low time/temperature relationship

Where suspended solid level is low and feed can be passed

APV Evaporator Hndbook

12/6/00 11:08 AM Page 14

A Junior version of the

FALLING FILM PLATE