Ring Frame

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 13
At a glance
Powered by AI
The key takeaways are that ring spinning frames continue to be widely used due to their advantages over other spinning processes. They can spin any material to any count and deliver yarn with good structure and strength. The main components are drafting, twisting, and winding sections.

The main components of a ring spinning frame are the drafting system, twist insertion section, and winding section.

Factors that influence drafting include the drafting type and system design, drafting settings, selection of drafting elements, choice of appropriate draft, and service and maintenance.

RING FRAME

INTRODUCTION
The ring spinning will continue to be the most widely used form of spinning machine in the near future,
because it exhibits significant advantages in comparison with the new spinning processes.
Following are the advantages of ring spinning frame
It is universally applicable, i.e. any material can be spun to any required count
It delivers a material with optimum characteristics, especially with regard to structure and strength.
It is simple and easy to master
The know-how is well established and accessible for everyone

OPERATIONS OF RINGFRAME
To draft the roving until the required fineness is achieved
To impart strength to the fibre, by inserting twist
To wind up the twisted strand (yarn) in a form suitable for storage, transportation and further processing.

DRAFTING

Drafting arrangement is the most important part of the machine. It influences mainly evenness
and strength. The following points are therefore very important

Drafting type

Design of drafting system

Drafting settings

Selection of drafting elements like cots, apron, traveller etc

Choice of appropriate draft

Service and maintenance

Drafting arrangement influence the economics of the machine - directly by affecting the end
break rate and indirectly by the maximum draft possible.

If higher drafts can be used with a drafting arrangement, then coarser roving can be used as a
feeding material. This results in higher production rate at the roving frame and thus reducing the
number roving machines required, space, personnel and so on.

In fact increase in draft affects the yarn quality beyond certain limit. Within the limit some studies
show that increase in draft improves yarn quality. The following draft limits have been established
for practical operation:

Carded cotton- upto 35

Carded blends - upto 40

Combed cotton and blends(medium counts) - upto 40

Combed cotton and blends(fine counts) - upto 45

Synthetic fibres - upto 50

The break draft must be adapted to the total draft in each case since the main draft should not
exceed 25 to 30. It should be noted that higher the break draft, more critical is the break draft
setting.

The front top roller is set slightly forward by a distance of 2 to 4mm relative to the front bottom
roller, while the middle top roller is arranged a short distance of 2mm behind the middle bottom
roller.

Overhang of the front top roller gives smooth running of the top rollers and shortens the spinning
triangle. This has a correspondingly favourable influence on the end break rate.

Rubber cots with hardness less than 60 degrees shore are normally unsuitable because they
cannot recover from the deformation caused by the pressure on the top roller while running.

Soft rubber cots for top rollers have a greater area of contact, enclose the fibre strand more
completely and therefore provide better guidance for the fibres. However softer cots wear out
significantly faster and tend to form more laps.

Normally harder rubber cots are used for back top rollers, because the roving which enters the
back roller is compact, little twisted and it does not require any additional guidance for better fibre
control.

In the front top roller, only few fibres remain in the strand and these exhibit a tendency to slide
apart. Additional fibre guidance is therefore necessary. Therefore rubber cots with hardness
levels
of
the
order
80
degrees
to 85 degrees shore are mostly used at the back roller and 63 degrees and 65 degrees at the
front roller.

If coarse yarns and synthetic yarns are being spun, harder rubber cots are used at the front roller
because of increased wear and in the case of synthetic yarns to reduce lap-ups.

Three kinds of top roller weighting (loading) are presently in use

Spring loading

Pneumatic loading

Magnetic weighting

With pneumatic loading system, the total pressure applied to all top rollers is obtained by simple
adjustment of the pressure in the hose using pressure reducing valve. Moreover the rubber-cots
will not get deformed if the machine is stopped for a longer duration, because the pressure on top
rollers can be released to the minimum level.

The fibre strand in the main drafting field consists of only a few remaining fibres. There is hardly
any friction field and fibre guidance provided by the rollers alone is inadequate. Special fibre
guiding devices are therefore needed to carry out a satisfactory drafting operation. Double apron
drafting arrangements with longer bottom aprons is the most widely used guiding system in all
the modern ringframes.

In double apron drafting system two revolving aprons driven by the middle rollers form a fibre
guiding assembly. In order to be able to guide the fibres, the upper apron must be pressed with
controlled force against the lower apron. For this purpose, a controlled spacing (exit opening),
precisely adapted to the fibre volume is needed between the two aprons at the delivery. This
spacing is set by "spacer" or "distance clips". Long bottom aprons have the advantage in
comparison with short ones, that they can be easily replaced in the event of damage and there is
less danger of choking with fluff.

Spindles and their drive have a great influence on power consumption and noise level in the
machine. The running characteristics of a spindle, especially imbalance and eccentricity relative
to the ring flange, also affect yarn quality and of course the number of end breakage. Almost all
yarn parameters are affected by poorly running spindles. Hence it should be ensured that the
centering of the spindles relative to the rings is as accurate as possible. Since the ring and
spindle form independent units and are able to shift relative to each other in operation, these two
parts must be re-centered from time to time. Previously, this was done by shifting the spindle
relative to the ring, but now it is usually carried out by adjusting the ring.

In comparison with Tangential belt drive, the 4-spindle drive has the advantages of lower noise
level and energy consumption, and tapes are easier to replace.

Lappet guide performs the same sequence of movements as the ring-rail, but with a shorter
stroke, this movement of the guide ensures that differences in the balloon height caused by
changes
in
the
ring
rail
positions do not become too large. This helps to control the yarn tension variation with in control,
so that ends down rate and yarn characteristics are under control.

Spindles used today are relatively long. The spacing between the ring and the thread guide is
correspondingly long, thus giving a high balloon. This has two negative influences.

A high balloon results in large bobbin diameter leading to space problems

Larger the balloon diameter , higher the air drag on the yarn. This inturn causes increased
deformation of the balloon curve out of the plane intersecting the spindle axis. This
deformation can lead to balloon stability, there is increase danger of collapse.

Both these disadvantages result in higher yarn tension, thereby higher endbreaks. In order to
avoid this, balloon control rings are used. It divides the balloon into two smaller sub-balloons.
Inspite
of
its
large
overall
height, the double-balloon created in this way is thoroughly stable even at relatively low yarn
tension.

Balloon control rings therefore help to run the machine with long spindles(longer lift) and at high
spindle speed, but with lower yarn tension. Since the yarn rubs against the control ring, it may
cause roughening of the yarn.

Most ends down arise from breaks in the spinning triangle, because very high forces are exerted
on a strand consisting of fibres which have not yet been fully bound together in the spinning
triangle.

End break suction system has a variety of functions.

It removes fibres delivered by the drafting arrangement after an end break and thus
prevents multiple end breaks on neighbouring spindles.

It enables better environmental control, since a large part of the return air-flow of the aircondition system is led past the drafting system, especially the region of the spinning
triangle.

In modern installations, approx. 40 to 50 % of the return air-flow passes back into the duct
system of the air-conditioning plant via the suction tubes of pneumafil suction system.

A relatively high vacuum must be generated to ensure suction of waste fibres


o for cotton - around 800 pascals
o for synthetic - around 1200 pascals

A significant pressure difference arises between the fan and the last spindle. This pressure
difference will be greater , the longer the machine and greater the volume of air to be
transported. The air flow rate is normally between 5 and 10 cubic meter/ hour.

Remember that the power needed to generate an air-flow of 10 cubic meter/ hour , is
about 4.5 times the power needed for an air flow of 6 cubic meter/ hour, because of the
significantly higher vacuum level developed at the fan.

SPINNING GEOMETRY

From Roving bobbin to cop, the fibre strand passes through drafting arrangement, thread guide,
balloon control rings and traveller. These parts are arranged at various angles and distances
relative to each other. The distances and angles together are referred to as the spinning
geometry, has a significant influence on the spinning operation and the resulting yarn. They are

Yarn tension

Number of end breaks

Yarn irregularity

Binding-in of the fibres

Yarn hairiness

Generation of fly etc.

Spinning Triangle:
Twist in a yarn is generated at the traveller and travel against the direction of yarn movement to
the front roller. Twist must run back as close as possible to the nip of the rollers, but it never
penetrates completely to the nip because, after leaving the rollers, the fibres first have to be
diverted inwards and wrapped around each other. There is always a triangular bundle of fibres
without twist at the exit of the rollers, this is called as SPINNING TRIANGLE. Most of the end
breaks originate at this point. The length of the spinning triangle depends upon the spinning
geometry and upon the twist level in the yarn.

The top roller is always shifted 3 to 6 mm forward compared to bottom roller. This is called top
roller overhang. This gives smoother running and smaller spinning triangle. The overhang must
not be made too large, as the distance from the opening of the aprons to the roller nip line
becomes too long resulting in poorer fibre control and increased yarn irregularity.

Continuous variation of the operating conditions arises during winding of a cop. The result is that
the tensile force exerted on yarn must be much higher during winding on the bare tube than
during winding on the full cop, because of the difference in the angle of attack of the yarn on the
traveller. When the ring rail is at the upper end of its stroke, in spinning onto the tube, the yarn
tension is substantially higher than when the ring rail is at its lowermost position. This can be
observed easily in the balloon on any ring spinning machine.

The tube and ring diameters must have a minimum ratio, between approx. 1:2 and 1:2.2, in order
to ensure that the yarn tension oscillations do not become too great.

Yarn tension in the balloon is the tension which finally penetrates almost to the spinning triangle
and which is responsible for the greater part of the thread breaks. It is reduced to a very small
degree by the deviation of the yarn at the thread guide. An equilibrium of forces must be obtained
between the yarn tension and balloon tension.

PROCESS PARAMETERS IN SPINNING


Introduction
Ringframe Technology is a simple and old technology, but the production and quality requirements at
the present scenario puts in a lot of pressure on the Technologist to select the optimum process
parameters and machine parameters, so that a good quality yarn can be produced at a lower
manufacturing cost.
Following are the points to be considered in a ringframe :

Draft distribution and settings


Ring and travellers
Spindle speed
Twist
Lift of the machine
Creel type
Feed material
Length of the machine
Type of drive, above all
Raw material characteristic plays a major role in selecting the above said process parameters

Technical information and guidelines are given below based on the learnings from personal experience
and discussions with Technologists. This could be used as a guideline and can be implemented based
on the trials taken at site. Some of this information can be disproved in some other applications,
because many of the parameters are affected by so many variables. A same machine or raw material
cannot perform in the same way in two different factories. This is because of the fact that no two
factories can be identical.
Drafts
The break draft should depend upon the following,

Fibre type
Fibre length
Roving T.M
Main draft

Some examples are given below,


Normally 1.13 to 1.18 break draft is used for

100%cotton , Poly/cotton blend, 100% synthetic


Roving T.M. upto 1.3 for cotton and 0.80 for Poly/cotton blend, 0.5 to 0.7 for synthetic
Ring frame back zone setting of 60mm for fibres upto 44mm and 70mm for fibres upto 51mm
Total draft in ringframe upto 35

1.24 to 1.4 break draft is used for

100% cottton, poly/cotton blend, 100%synthetic fibre


Strongly twisted roving i.e. higher than the above mentioned T.M.s
Total draft from 33 to 45
Back zone setting (R.F) around 52mm for fibres upto 44mm and 60mm for fibres upto 51mm

If the total draft is more than 45 or the fibre length is more than 51 and the fibre is a fine fibre (i.e. more
number of fibres in the cross section)with a very high interfibre friction, break draft more than 1.4 is
used.
Please note that for most of the application, lower break draft with wider setting is used. With higher
break drafts, roller setting becomes very critical. Higher the break draft, higher the chances for thin
places i.e. H1 classimat faults.
Higher draft with improper back zone setting will lead to thin places and hence more end breaks even
though more twist flows into the thin yarn.
Main Draft Zone
Mostly for cotton fibres, short cradles are used in the top arm. Front zone setting is around 42.5 mm to
44 mm depending upon the type of drafting system. The distance between the front top roller and top
apron should be around 0.5 to 0.7mm when correct size top roller is used. This is normally taken care of
by the machinery manufacturer. If a technician changes this setting, this will surely result in more
imperfections, especially with carded count the impact will be more. Therefore when processing cotton
fibres, care should be taken that the front zone setting should be according to the machinery
manufacturers recommendation.
For synthetic fibres upto 44 mm, it is better to use short cradles.Even with 42.5 mm bottom roller setting,
44 mm fibre works well without any problem. Because, the clamping distance will be around 52 mm or
50 mm. The imperfections and U% achieved with short cradle is better than with medium cradle (52mm
setting).
Instead of using medium cradle for processing 44mm synthetic fibre, it is always better to use short
cradle with 1 or 2mm wider setting than the recommended to avoid bottom apron damages. If a mill has
got a problem of bottom roller lapping, the apron damages are extremely high, it is better to use short
cradle for 44 mm fibre and widen the setting by 1 or 2mm. This will minimise the complaints and
improve the basic yarn quality also.

Please note that if the bottom apron breakages are high, then the mill is working with a lot of bottom
apron which is defective and with a lot of top roller which is defective. Both the defective parts produces
a defective yarn, which can not rejected by older version of yarn clearers, and improperly set new type
of clearers. This yarn will very badly affect the fabric appearance.
Therefore it is always advisable to use a wider front zone setting upto 2mm , if the mill faces a problem
of excessive bottom roller lappings. Please note that the defective bottom apron and top roll will not
only affect the quality, but also the production, because the defective bottom apron and top roll make the
spindle a sick spindle which will be prone to end breaks. A wider front zone setting will increase the
imperfection and uster, but there will not be major deviations of yarn quality.
Nose bar height setting is very important. Depending upon the design, it is 0.7mm or 0.9 mm. Variation
in height setting will affect the yarn quality and the apron movement. The distance between nose bar
and middle bottom roller should be less than apron thick ness or more than 3 mm to avoid apron
buckling if there is any disturbance in apron movement.
Ring and Traveller

Ring diameter, flange width and ring profile depends upon the fibre, twist per inch, lift of the
machine, maximum spindle speed, winding capacity etc.

Operating speed of the traveller has a maximum limit, because the heat generated between ring
and traveller should be dissipated by the low mass of the traveller with in a short time available.

If the cotton combed yarn is for knitting, traveller speed will not be a limiting factor. Since yarn TPI
is less, the yarn strand is not strong enough. Therefore the limiting factor will be yarn tension.

Following points to be considered


1 For 12s to 24s , 42mm ring with 180 mm lift can be used
2 For 24s to 36s, 40 mm ring with 180 lift can be used
3 For 36s to 60s , 38 mm ring with 170 mm lift can be used
4 For 70s to 120s, 36 mm ring with 160 mm lift can be used.
5 If winding is a problem, it is better to go for reduced production with bigger ring dia.
6 Anti-wedge ring profile is better, because of better heat dissipation
7 Elliptical traveller should be used, to avoid start-up breaks in hosiery counts
8 Special type of traveller clearer can be used to avoid accumulation of fibre on the traveller
as traveller with waste does not perform well during start-up.

For polyester/cotton blends and cotton weaving counts yarn strength is not a problem. The
limiting factor will be a traveller speed. For a ring diameter of 40 mm, spindle speed upto 19500
should not be a problem. Rings like Titan (from Braecker), NCN (bergosesia) etc, will be able to
meet the requirements.

For spindle speeds more than 20000 rpm, ORBIT rings or SU-RINGS should be used. As the
area of contact is more with this rings, with higher speeds and pressure, the heat produced can
be dissipated without any problem. Normal ring and traveller profile will not be able to run at
speeds higher than 20000 to produce a good quality yarn.

ORBIT rings will be of great help, to work 100% polyester at higher spindle speeds. Because, of
the tension, the heat produced between ring and traveller is extremely high. But one should
understand, that, the yarn strength of polyester is very high. Here the limiting factor is only the
heat
dissipation.
Therefore ORBIT RINGS with high area of contact will be able to run well at higher spindle
speeds when processing 100% polyester.

While running 100% cotton, the fibre dust in cotton, acts like a lubricant. All the cottons do not
form same amount of lubricating film. If there is no fibre lubrication, traveller wears out very fast.
Because of this worn out or burn out travellers, microwelding occurs on the ring surface, which
results in damaged ring surface, hence imperfections and hairiness increases in the yarn.

Lubrication is good with west african cottons. It may not be true with all the cottons from West
Africa. In general there is a feeling, cottons from Russia, or from very dry places, lubrication is
very bad. If the fibre lubrication is very bad, it is better to use lighter travellers and change
the travellers as early as possible.

Traveller life depends upon the type of raw material, humidity conditions, ringframe speeds, the
yarn count, etc. If the climate is dry , fibre lubrication will be less while processing cotton.

Traveller life is very less when Viscose rayon is processed especially semi dull fibre, because of
low lubrication. Traveller life is better for optical bright fibres.

Traveller life is better for Poly/cotton blends, because of better lubrication between ring and
traveller.

Because of the centrifugal force exerted by the traveller on the yarn, the particles from the fibre
fall on the ring where the traveller is in contact. These particles act like a lubricating film between
ring and traveller.

Rubber Cots and Aprons

For processing combed cotton, soft cots (60 to 65 degree shore hardness) will result in lower U
%, thin and thick places.

There are different types of cores (inner fixing part of a rubber cot) available from different
manufacturers. Aluminum core, PVC core etc. It is always better to use softer cots with aluminum
core.

When softer cots are used, buffing frequency should be reduced to 45 to 90 days depending
upon the quality of the rubber cots, if the mill is aiming at very high consistent quality in cotton
counts.

If the lapping tendency is very high when processing synthetic fibres for non critical end uses, it
is better to use 90 degree shore harness cots, to avoid cots damages. This will improve the
working and the yarn quality compared to working with 83 degree shore hardness.

If rubber cots damages are more due to lapping, frequent buffings as high as once in 30 days will
be of great help to improve the working and quality. Of course, one should try to work the
ringframe without lapping.

The basic reasons for lapping in the case of processing synthetic fibre is

End breaks

Pneumafil suction

Rubber cots type

Fibre fineness

Oil content(electrostatic charges)

Department temperature and humidity

Almost all the lappings originate after an end break. If a mill has an abnormally high lapping
problem the first thing to do is to control the end breaks,
1 After doffing
2 During speed change
3 During the maximum speed

by optimising the process paramters.


It is obvious that fine fibres will have a stronger tendency to follow the profile of the roller.
Therefore lapping tendency will be more.

If the fibre is fine, the number of fibres in the cross section will be more, therefore lapping
frequency will be more.

If the pressure applied on the roller is more, then lapping tendency will be more. Hence fine and
longer fibres will have more tendency for lapping because of high top roller pressure required to
overcome the drafting resistance.

If the pneumafil suction is less, the lapping tendency will be more both on top and bottom roller.
But the pneumafil suction depends on the fan diameter, fan type, fan speed, duct design, length
of the machine, profile of the suction tube etc. If any one of the above can be modified and the
suction can be improved, it is better to do that to reduce the lapping.

The closer the setting between the suction nozzle and the bottom roller, the higher the suction
efficiency and lower the lapping propensity.

Higher roving twist will reduce the lapping tendency to some extent. Therefore it is better to have
a slightly higher roving twist, provided there is no problem in ringframe drafting, when the lapping
tendency is more.

With Softer rubber cots lapping tendency will be more due to more surface contact.

The most minute pores, pinholes in the rubber cots or impurities in the cots can cause lapping.
Therefore the quality of buffing and the cots treatment after buffing is very important. Acid
treatment is good for synthetic fibres and Berkolising is good for cotton.

Electrostatic charges are troublesome especially where relatively large amount of fibre are being
processed in a loose state e.g. drawframe, card etc. Lapping tendency on the top roll increases
with increasing relative humidity. The frequently held opinion is that processing performance
remains stable at a steady absolute relative humidity, i.e. at a constant moisture content per Kg of
dry air.

Twist
The strength of a thread twisted from staple fibres increases with increasing twist, upto certain level.
Once it reaches the maximum strength, further increase in twist results in reduction in yarn strength

Coarser and shorter fibres require more Twist per unit length than finer and longer fibres.
Twist multiplier is a unit which helps to decide the twist per unit length for different counts from
the same raw material. This is nothing but the angle of inclination of the helical disposition of the
fibre in the yarn. This is normally expressed as
TWIST PER INCH = TWIST MULTIPLIER * SQRT(Ne)

If the two yarns are to have the same strength, then the inclination angles must be the same.
For 40s combed knitting application, if the average micronaire of cotton is 3.8 and the 2.5% span
length is around 29 mm, Twist multiplier of 3.4 to 3.5 is enough . If the average micronaire is
around 4.3, it should be around 3.6 to have better working in Ring frame.
Cotton combed knitting T.M. = 3.4 to 3.6
Cotton combed weaving T.M. = 3.7 to 3.8
Cotton carded knitting T.M. = 3.8 to 4.0
Cotton carded weaving T.M. = 3.9 to 4.2

The above details are for cottons of 2.5% span length of 27 to 30 mm and the average Micronaire of 3.7
to 4.4. For finer and longer staple, the T.M. will be lower than the above.

In general for processing poly/viscose , the T.M. is as follows :

51 mm, 1.4 denier fibre : T.M. = 2.7 to 2.9 for knitting application
51 mm, 1.4 denier fibre : T.M. = 2.9 to 3.1 for weaving application
44 mm, 1.2 denier fibre : T.M. = 2.9 to 3.0 for knitting application
44 mm, 1.4 denier fibre : T.M. = 3.0 to 3.1 for knitting application
38 mm, 1.2 denier fibre : T.M. = 3.1 to 3.3 for knitting application

The above detail is self explanatory


Other Important points in Ring-spinning
The following ROVING parameters will affect the ring frame process parameters

Roving T.M.

Bobbin weight

Bobbin height

Higher the roving T.M., wider the back bottom roller setting or higher the break draft in ring frame.

For combed material the creel height should be as low as possible in ringframe.

Very long creel heights in ringframe, lower roving T.M. and heavier roving package will result in
many long thin places in the yarn.(especially in combed hosiery counts)

In general 16 x 6 " bobbins are used. This helps to increase the spare rovings per machine with
higher creel running time. Therefore one should aim at increasing the bobbin weight as well as
increasing the number of spare rovings in the ring frame.

Normally 6 row creels are used in modern ring frames. Six row creels will accommodate more
spare rovings compared to 5 row creels.(around 150 rovings for 1000 spindle machine.) Creel
height should be as low as possible for cotton combed counts. Spare rovings will improve the
operators efficiency.

Shorter machines are always better compared to longer machines. But the cost per spindle will
go up. For cotton , polyester/cotton blends, poly/viscose(upto 44mm length), number of spindles
upto 1200,br> should not be a problem. But maintenance is more critical compared to shorter
machines.

For synthetic fibres with very high drafting resistance, it is better to use shorter machines,
because the load on break draft gears and on second bottom rollers will be extremely high. If
long machines are used and the maintenance is not good for such application, the bearing
damages, gear damages, bottom roller damages etc. will increase. This will result in coarse
counts, higher count C.V., long thin and thick places.

Four spindle drive is always better compared to Tangential belt drive. Because small variation in
machining accuracy of bolster , spindle beam etc will affect the spindle speeds, thereby the twist
per inch. Waste accumulation between contact rollers, bent contact rollers, damaged contact
rollers, oil spilling from any one spindle etc. will affect the spindle speeds and thereby TPI. The
spindle speed variation between spindles in a 5 year old ringframe will be very high incase of
tangential belt drive compared to 4 spindle drive.

Noise level and energy consumption will be low in 4 spindle drive compared to Tangential belt
drive.

When processing coarse counts at higher speeds, the air current below the machine is a big
problem with 4 spindle drive . This is due to the more running parts like tin rollers and jockey
pullys. This will lead to more fluff in the yarn, if humidification system is not good enough to suck
the floating fluff.

If spindle speeds is high for cotton counts, every end breaks will result in more fluff in the
department due to the free end of the yarn getting cut by the traveller when the distance between
traveller and the bobbin with the yarn is less. Higher the delay in attending the end break , higher
the fly liberation. If the number of openings of return air system for a ringframe is less and the
exhaust air volume is not sufficient enough, then fly liberation from an end break will increase the
endbreaks and thereby will lead to multiple breaks. End break due to a fly entering the traveller
will get struck with the traveller and will result in heavier traveller weight and that particular
spindle will continue to work bad.

Multiple breaks are very dangerous, as it will result in big variation in yarn hairiness and the
ringframe working will be very badly affected due to heavier travellers because of the fluff in the
traveller.

Dry atmosphere in ringframe department will result in more yarn hairiness, more fly liberation and
more end breaks.

It is a good practice to change spindle tapes once in 24 months. Worn out spindle tapes will
result in TPI variations which is detrimental to yarn quality.

You might also like