NE845 User Manual

Rolling Shutter Sliding Door Gate controller
NE-845-230Vac
Features:
1. Realize motor rotation, reversal and pause.
2. Accept upper and lower limit switches
3. Can be connected to lamp, the lamp can work as lighting or flash indication by setting
controller
4. Running time can be set
5. S-closing delay time can be set
6. Meet resistance rebound when connected to the photocell sensor
7. 1 or 4 key Control mode selectable
8. The controller can be locked or unlocked by remote control
System Specifications:
Remote control:
Frequency: 433.92 MHz
Voltage: 12V
Operating mode: 1key/4key
UP: control gate running up

DOWN: control gate running down
STOP: control gate to stop
LOCK: press and hold 3 receiver be locked,
press and hold 3 again to unlock receiver be activated

NE-845-230Vac
Receiver:
Working voltage: 220VAC
Working current: <100mA
Frequency: 433.92Mhz
Maximum capacity for remote: 80pcs fixed code/learning code or 15pcs rolling code
Maximum running time: 4min
Maximum self-closing delay time: 10min
Size & Weight: 123*78*35mm,
Main function operating:

Before working:
1. Remote control learning
Hold pressing the LEARN button until the red LED extinguish, then release the
LEARN button, then the controller-related information is deleted, restored to
factory settings (running time 60S, self-closing delay time 30S); press LEARN
button again, red LED lit, and release the LEARN button, LED extinguish, indicate
receiver turn into learning state, press any key except for LOCK key on the remote
control to learn, LED flashes five times indicate learning success.
2. Maximum running time setting
After learning remote control, press DOWN key, door moving down untill door fully
reach down limit switch, and then press the TIME button on receiver, the red LED
lit, release the TIME button, LED remain lighting Always, then press UP key, the
red LED and indication relay will flash ever 600ms, the controller remains in this
state until the door fully reach up limit switch, and then press DOWN key, red LED
and indication relay stop flash, success to set maximum running time.
3. Self-closing delay time setting
Press TIME button, the red LED lit, release the TIME button, LED stays on, then
press the STOP key, the red LED and indication relay will flash ever 250ms, the
system remains in this state until STOP key is pressed again, then success to set
self-closing delay time.
4. The system mode settings
Select the 4 modes AC, L/R, 1/4KEY, F/L depend on environment.
AC---enable this mode to start the self-closing delay time. System will perform
self-closing action after delay time.
L/R--- this mode is enabled, Uplink and Downlink will be exchanged
1/4KEY---this mode is enabled, only 1 key on remote control to control system.
F/L--- this mode is enabled, lamp with lighting function; not enabled, lamp with

NE-845-230Vac
flash indication
On Working:
4KEY mode
The uplink and downlink output can be set via L/R mode, uplink and downlink is
described below base on L/R mode is not enabled.
Upward movement:
When the door is in the case of non-full opened or upward movement of
non-being, you can press UP key to execute upward movement, in the
upstream process, you can control door to stop and reverse downward
movement. Each time updates run action, the maximum running time is
reset. If you do not change the running motion, upstream action will stop
until the door arrive at up limit switch or the maximum running time over.
At this time if AC is enabled, the system start time for self-closing delay,
in timing process if encounter obstacles or received signal from STOP key,
the time period is cleared, re-timing. Running downstream action when
timing is over.
Downward movement:
When the door is in the case of non-fully closed or downward
movement of non-being, you can press DOWN key to execute downward
movement, in the downstream process, you can control door to stop and
reverse upward movement. Each time updates run action, the maximum
running time is reset. Downstream process, if encounter an obstacle, the
system will repeat upward movement after delay 0.5 second.
1KET mode
The uplink and downlink output can be set via L/R mode, uplink and downlink is
described below base on L/R mode is not enabled.
Movement process:
Under 1KEY mode, only use 1 key has been learned to control upstream Stop - downstream - Stop - upward circular motion, other things same with
4KEY mode.
Lighting functions:
The controller provides 220VAC lighting and flashing functions are optional. To meet
different lighting situations.
When F/L mode is enable, lamp with lighting function. The remote control can be in any
state through short press LOCK key to turn on/off the lamp. Without any other operations,
the lamp automatically turn off after 5 minutes, otherwise restart delay 5 minutes.

NE-845-230Vac
Internal Structure Description

NE-845-230Vac

NE845 User Manual

Uploaded by

Copyright:

Available Formats

NE845 User Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

NE845 User Manual

Uploaded by

Copyright:

Available Formats

What are the main features of the Rolling Shutter - Sliding Door Gate controller?

How do you set the maximum running time and self-closing delay time of the controller?

Rolling Shutter Sliding Door Gate controller

UP: control gate running up

Rolling Shutter Sliding Door Gate controller

Main function operating:

Rolling Shutter Sliding Door Gate controller

Rolling Shutter Sliding Door Gate controller

Internal Structure Description

Rolling Shutter Sliding Door Gate controller

You might also like