Scribd
Upload
128 views

Ciscom Manual

The document provides instructions for installing and using CISCOM software for Phocos CIS solar charge controllers. The software allows users to configure settings for single and dual load controllers like SOC/LVD levels and view datalogger values. It has options for non-expert and expert modes, with expert offering more configuration settings. Instructions are included for installing driver software and selecting COM ports for the MXI-IR interface. The summary provides an overview of the key capabilities and information covered in the user manual.

Uploaded by

suarezjose29
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
128 views

Ciscom Manual

The document provides instructions for installing and using CISCOM software for Phocos CIS solar charge controllers. The software allows users to configure settings for single and dual load controllers like SOC/LVD levels and view datalogger values. It has options for non-expert and expert modes, with expert offering more configuration settings. Instructions are included for installing driver software and selecting COM ports for the MXI-IR interface. The summary provides an overview of the key capabilities and information covered in the user manual.

Uploaded by

suarezjose29
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 29

CISCOM Manual

Software for Phocos CIS Controller Series:


Single Load: CIS, CIS-N, CIS-LED, CIS-MPPT
Dual Load: CIS, CIS-N

www.phocos.com

version 20130418

Contents

1. Software Installation
2. Software Features / Controller
3. Drivers for Interface MXI-IR
4. Software Features
4.1. Expert Mode and Non-Expert Mode
4.1.1. Non-Expert Mode:
4.1.2. Expert Mode:
4.2. Daily / Monthly Datalogger Values

3
3
4
7
8
8
20
22

Please note: All settings apply to a 12 V system. Settings of a 24 V system


are the same as in a 12 V system.

1. Software Installation
Dear customer,
Please double click on the setup.exe file and follow the setup instructions.
If the Microsoft dotnet framework 4.0 is not installed on your PC the setup will
request you to install the framework.

2. Software Features/Controller
Not every software feature is available for all CIS controllers. Please find below a
list stating which feature is available for which controller type.
For CIS single load and CIS dual load
CIS single Load: CIS, CIS-LED
- Settings:
- nightlight function settings
- SOC/LVD settings
- battery type
- Save and load settings again
For CIS-MPPT:
- Settings:
- nightlight function settings
- SOC/LVD settings
- battery type
- Save and load settings again
- Datalogging:
- last 30 days (dataset per day)
- last 24 months (dataset per month)

3. Drivers for the Interface MXI-IR


Please connect the MXI-IR to your PC/laptop and install the USB driver and the
virtual RS232 driver.

Both MXI-IR drivers can be found in the following folder:


MXI-IR/Windows_7
MXI-IR/Windows_Vista
MXI-IR/Windows_XP
depending of your operating system.

Please select the number of your COM port in the CISCOM software under the
menu item Inferface.

Please select the number of your COM Port in the CISCOM software under the
menu point Interface.

4. Software Features
Start page of the CISCOM software

4.1. Expert Mode and Non-Expert Mode


4.1.1. Non-Expert Mode:
The default setting is the non-expert mode.
The window below shows the non-expert mode with the same setting possibilities as with the
remote control (CIS CU).
The non-expert mode offers different setting possibilities for the CIS single und dual loads.

The non-expert mode should help you easily set your CIS remote control or transmit the settings
via the MXI-IR Interface to your CIS-controller.
By clicking on Send Settings, the settings will be sent to your controller via MXI-IR.

Select your CIS Controller Type

10

Nightlight Function
The Back and Next buttons enable you to go through the whole setting possibilities of the
single load CIS controller.
Please select your nightlight program. Results of the settings can be directly visualized on the
graphic.

11

CIS Dual Load


Lights for load 1 and 2 are on
- based on the middle of the night
- based on dusk and dawn

Load 1

Load 2

12

CIS Single Load (with Dimming Function)


Light on for Load 1
- based on middle of the night
- based on dusk and dawn

Dimming
Time when the controller starts to dim
- based on middle of the night
- based on dusk and dawn
- Brightness while light
is dimmed

SOC (State of Charge) / LVD (Low Voltage Disconnect)

13

Changing the Low Voltage Disconnect Levels

14

CIS Dual Load


Graph 1: Disconnect level for light 1

Graph 2: Disconnect level for light 2

15

CIS Single Load with Dimming Function


Graph 1: Disconnect level for light

Graph 2: Dimming level

16

Night Detection

Standard setting

Default standard
value: 8.0 V

17

Battery Type
Please select the battery type (in this case a sealed battery is selected)
Display on the remote control (CIS CU):
Lead acid battery
Sealed battery

18

Print, Send and Save Settings


You can select a printer and print your individual CIS settings. You can also send
them to the CIS Controller via MXI-IR or save the settings on your computer.

19

4.1.2 Expert Mode


With the button expert mode enabled / Expert mode disabled you can enable
and disable the expert mode.
The expert mode offers you more possibilities to add settings.

20

Settings in the Expert Mode


Standard settings: Here you can modify the same settings as in the non-expert
mode but in an extended range.
Extended settings: Here you can modify even more than the standard settings.
If you want to also transmit the extended settings, please check the box send
extended settings.
Note: Temperature compensation will not affect behavior of CIS (positive grounded)
controllers.

21

4. 2. Daily / Monthly Datalogger Values


In the menu you can switch between Settings and Datalogger and status. Please
note that the Datalogger and status values feature is only possible with the CISMPPT controller.

22

Status Values
The status value settings display many different values of your current system
such as:
- Load and charge currents
- Battery voltage
- Loading error messages
- Charging error messages, etc.

23

Datalogger Values
By selecting Datalogger SOS in the menu, the State Of System (SOS) values will be
displayed. These are the collected datalogger values since the last clearing of the
datalogger. You will find the button Clear datalogger at the bottom on the right.

24

Daily / Monthly Datalogger Values


If you select the menu point Daily datalogger values or Monthly datalogger
values you will get more detailed values.

25

Datalogger Graphs
If you select the menu point Graph daily values or Graph monthly values you will
get more detailed values.

26

Save Datalogger Values


If you want to save the datalogger values please click on the menu point Save
data. In the opening window click on the button Save CISCOM data .cisdl

27

Controller Identification
You can send an individual text to each CIS-MPPT controller.
Enter the text and click on the button Send controller individual text.
If you read in the datalogger values, you will also obtain your controllers identification.

28

Phocos AG
Magirus-Deutz-Str. 12
89077 Ulm, Germany
Tel./Phone +49 731 9380688-0
Fax
+49 731 9380688-50
[email protected]
www.phocos.com

Subject to change without notice

You might also like