Scribd Logo
Upload

Welcome to Scribd!

  • 223 views

    Eltex - FD Sensors

    Uploaded by

    saad naveed
    The document describes an ELTEX optical weft stop motion system, including a weft sensor, central control unit, and their functions. The optical weft sensor detects wefts across the entire air channel without damaging the reed. The central control unit has two channels to detect weft breaks and uses relay and electronic outputs to stop the loom. It can synchronize to the loom and has sensitivity adjustment, indicators, and testing capabilities.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Eltex - FD Sensors

    Uploaded by

    saad naveed
    223 views2 pages
    The document describes an ELTEX optical weft stop motion system, including a weft sensor, central control unit, and their functions. The optical weft sensor detects wefts across the entire air channel without damaging the reed. The central control unit has two channels to detect weft breaks and uses relay and electronic outputs to stop the loom. It can synchronize to the loom and has sensitivity adjustment, indicators, and testing capabilities.

    Original Description:

    FD sensors

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes an ELTEX optical weft stop motion system, including a weft sensor, central control unit, and their functions. The optical weft sensor detects wefts across the entire air channel without damaging the reed. The central control unit has two channels to detect weft breaks and uses relay and electronic outputs to stop the loom. It can synchronize to the loom and has sensitivity adjustment, indicators, and testing capabilities.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    223 views2 pages

    Eltex - FD Sensors

    Uploaded by

    saad naveed
    The document describes an ELTEX optical weft stop motion system, including a weft sensor, central control unit, and their functions. The optical weft sensor detects wefts across the entire air channel without damaging the reed. The central control unit has two channels to detect weft breaks and uses relay and electronic outputs to stop the loom. It can synchronize to the loom and has sensitivity adjustment, indicators, and testing capabilities.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    ELTEX optical weft stop motion

    Weft sensor
    The optical weft sensor is of reflecting type. The
    weft sensor should be fitted on the front of the
    reed. It will not damage the reed. The weft
    sensor has a set of optical components enabling
    the detection of the weft across the entire air
    channel.

    The size of the optical weft sensor, the angles of


    the optical components and the sensor support
    must be made according to the space available on
    the weaving machine and to the design of the
    reed.

    Central control unit 22000


    The central control unit is equipped with two channels and
    two inputs for weft sensors. The second channel is used for
    an ANTI weft sensor. This weft sensor should be placed on
    the reed, at a point the weft yarn does not reach, unless the
    weft is broken.
    The central control unit can detect both a positive and a
    negative change of the sensor signal. This means that both
    light and dark coloured yarns can be detected.

    Functions and specifications


    Power supply

    24 V DC

    Relay stop output

    The relay is normally energized. It drops for 1 second when a weft fault
    occurs.
    Max load on relay contacts: 2 x 1A / 125V AC or
    2 x 2A / 30 V DC

    Size

    Europe size board 100 x 160 mm.


    Equipped with a Europe connector DIN 41612 series D, 32 poles

    Electronic stop
    output

    An open collector output is also available. The output is short circuit to


    ground during 1 second when a weft fault occurs. Max load is 100 mA.

    Yarn arrival
    output

    One output for each channel is available notifying the arrival time of the yarn.
    The pulse is 50 ms long and the positive edge is synchronised with the arrival
    time of the yarn.

    Input synchronising To use the stop outputs on the central control unit, the unit must be
    switch
    synchronised with the machine. This can be done with a proximity switch or
    with an Eltex light switch. A positive pulse defines the time frame when the
    weft yarn arrival is expected. The yarn arrival outputs are available also when
    no synchronising switch is used.
    Syncronising switch With a connection shunt on the printed circuit board the input can be set
    function
    to suit a NPN or a PNP type proximity switch. If Eltex light switch is used,
    select the NPN position.
    Idle pick input

    An input to inhibit the stop outputs. This is used when the machine is
    weaving without weft (fringing).

    ON/OFF switch

    When the switch is OFF the stop outputs are inhibited. The machine can
    then run without weft.
    Other functions of the unit is still active.

    ANTI switch

    The switch will switch the ANTI weft sensor on or off.

    Filter switch

    On models where the second channel is used to detect if the weft yarn is
    passing too far out, this channel can be set so that it is less sensitive for dust
    particles passing the weft sensor. The switch has three positions.

    LED indicators

    There are five LED indicators:


    Stop channel 1
    Stop channel 2
    Signal from weft sensor channel 1
    Signal from weft sensor channel 2
    Signal from synchronising switch.

    Sensitivity

    A potentiometer is available to set the sensitivity in each channel.

    Test socket

    A five pole test socket is available with the following connections:


    Internal power +12 V DC
    Ground connection
    Signal from synchronising switch
    Yarn arrival output channel 1
    Yarn arrival output channel 2

    Box 24 SE-283 21 OSBY Sweden Tel. +46 479 53 63 00 Fax +46 479 53 63 99
    E-mail: [email protected] Web: www.eltex.se
    ELTEX U.S. INC.
    13031 E. Wade Hampton Blvd
    Greer, S C 29651
    USA
    Tel: 864-879-2131
    In U.S. toll free: 1-800-421-1156
    Fax: 864-879-3734
    Email: [email protected]
    2008-05-20/En/B-opto.pmd/TH-0054-03

    ELTEX MFG LTD


    Railway Road
    Templemore, Co. Tipperary
    Ireland
    Tel: 504-314 33
    Fax: 504-310 02
    Email: [email protected]

    POLSA-ELTEX S.L.
    Zamora, 103 - entlo 3
    ES-08018 Barcelona
    Spain
    Tel: 093-309 00 17
    Fax: 093-309 59 45
    Email: [email protected]

    You might also like