Parker RDH 1320-2

aerospace
climate control
electromechanical
filtration
fluid & gas handling
hydraulics
pneumatics
process control
sealing & shielding
Heavy Duty Hydraulic

Roundline Cylinders
Series RDH
Heavy Duty Hydraulic Roundline Cylinders

Series RDH
Catalog HY08-1320-2/NA
Series CHE
20 through 100mm Bore Sizes
Stroke Lengths to 150mm
Operating Pressure to 140 bar
4 Different Rod Ends Available
Series CHD
20 through 80mm Bore Sizes
Stroke Lengths to 100mm
Operating Pressure to 207 bar
4 Different Rod Ends Available
Accessories
Corrosion Resistant
Cast & Fabricated
Traditional Accessories
Metric Accessories
Stainless Steel Accessories
In line with our policy of continuing product improvement, specifications and information contained
in this catalog are subject to change.
Copyright 2011, 2012 by Parker Hannifin Corporation.
All rights reserved.
PRINTED IN THE U.S.A.
WARNING
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH,
PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from the Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product and/or system options for further investigation
by users having expertise. It is important that you analyze all aspects of your application, including consequences of any failure and review the information concerning the product
or system in the current product catalog. Due to the variety of operating conditions and applications for these products or systems, the user, through its own analysis and testing,
is solely responsible for making the final selection of the products and systems and assuring that all performance, safety and warning requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to change by Parker Hannifin Corporation
and its subsidiaries at any time without notice.
Offer of Sale
The items described in this document are hereby offered for sale by Parker Hannifin Corporation, its subsidiaries or its authorized
distributors. This offer and its acceptance are governed by provisions stated on a separate page of the document entitled Offer of Sale.
www.parker.com/cylinder
Parker Hannifin Corporation

Industrial Cylinder Division
Des Plaines, Illinois

Series RDH
Parker Hannifin is
the worlds largest
manufacturer of
Hydraulic, Pneumatic,
Electro-Hydraulic and
Electric cylinders.
With annual sales exceeding

$12 billion in fiscal year 2011,
Parker Hannifin is the worlds
leading diversified manufacturer
of motion and control technologies and systems, providing
precision-engineered solutions
for a wide variety of mobile,
industrial and aerospace
markets. The company employs
approximately 58,000 people
in 47 countries around the
world. Parker has increased
its annual dividends paid to
shareholders for 55 consecutive fiscal years, among
the top five longest-running
dividend-increase records in
the S&P 500 index. For more
information, visit the companys
website at www.parker.com, or
its investor information website
at www.phstock.com.
With our global presence in

47 countries, we are perfectly
suited to provide superior
customer service to any
location.
Here is a short list of what you
can expect from Parker:
Design and Application
Experience
Responsiveness
Fast Product Delivery
System Integration
Capabilities
Ingenuity and Creativity
Organizational Integrity
Highest Quality
Competitive Pricing
Financial Stability
Worldwide Support
Markets and Applications

Parker cylinders are utilized
worldwide in many markets
and applications, including:
Oil and Gas
Renewable Energy
Power Generation
Process Valves
Mining
Primary Metals
Metal Fabrication
Marine
Civil Engineering Projects
(including US Army Corps of
Engineers Projects)
Military and Commercial
Aerospace
Material Handling
Testing and Analysis
Construction
Wood Processing
Waste Processing
Automotive
Tire Press
Machine Tools
Entertainment

Series RDH Cylinders from Parker

Advanced Sealing Technology
Switch-Ready
All components are manufactured by Parker and designed for high

performance, long service life, low friction and zero leakage.
The Parker ALS Switch is the

lowest cost point feedback
solution for carbon steel cylinders
with a piston magnet ring.
Tri-lip rod seal (3 sealing edges!) and bi-directional piston seal

feature proven leak-free performance.
Durable polyurethane material is used to maximize seal life.
Nitrile end seals and backup rings on a smooth bore of the
cylinder body for optimal sealing and elimination of extrusion
problems.
Composite rod and piston wear rings are internally lubricated
for reduced friction and formulated for heavy-duty, load-bearing
applications.
Switches can be located

anywhere along the stroke and
in any orientation.
Unique round body brackets
minimize installation time.
EPS & CLS threaded switches are
available for end-of-stroke sensing.
Standard rod material is case-hardened, hard chrome plated

and polished to an optimum finish.
And since we make our own seals, all seals have immediate
availability in other popular compounds.
Easy Installation
Standard mounts and rod ends
accommodate commercially-available
NFPA accessories.
Proven Exterior Toughness

Steel cap, cylinder body and ports for highstrength in rough environments.
Case hardened, hard chrome plated and
polished carbon steel piston rod for damage
resistance, long rod seal life and low friction.
Composite Wear Rings

Parker WearGard bearing materials are backed by
over 30 years of manufacturing expertise.
Heat stabilized and internally lubricated for low
friction and maximum service life in any application.
Outboard urethane rod wiper seal to

remove external debris and adherents from
the piston rod.
Strength characteristics meet or exceed most metals

traditionally used in wear rings.
High quality paint coating for interior or

exterior applications.
Environmentally Friendly
RoHS-compliant materials
II

New Value from a Standard Platform

Advanced
Manufacturing
Lean Manufacturing
Principles
Cylinders, by nature, are customized

products. Whether it is something
basic, such as stroke length, or
something more complex, such as
a special head, raw material and
basic parts must be procured and
manufactured into components for
configured cylinders.
Parker Hannifin has utilized Lean

Manufacturing techniques for many
years, even before it was called by
name. Cellular Manufacturing, Value
Stream Mapping, Kaizen events,
Kanban, One-Piece Flow and other
influences are pervasive in our
manufacturing processes.
Organizing cylinder production and

assembly requires some degree
of planning. To do so, without
sacrificing customer service,
requires a sharp focus on advanced
manufacturing processes.
We now follow Lean Implementation

to focus all aspects of our operation
on the same goals for customer
service.
Late-Day Orders our West
Non-Standard Designs since
Made in U.S.A.
Series RDH cylinders are
manufactured in the USA. Location
is a significant part of our customer
service model. We believe that
customers value a domestic
presence, for many reasons.
A few include:
Quick Delivery standard
lead time is a few days, with

the capability of shipping some
cylinder configurations within 48
hours. We deliver to your request.
Made-To-Order we are able to
Coast presence can create an

order time advantage of up to
three hours for many US locations,
which may be instrumental in
keeping you on schedule.
Risk Management the absence

of international risks from dealing with non-domestic cylinder
suppliers will allow you to relax.
Our goal is to offer you the best
product, on time, with your financial concerns in mind.
50% of applications require

cylinders that are not catalogstandard, we organized our entire
culture for flexibility. Our manufacturing processes are prepared
to accommodate non-standard
designs with minimal lead-time
adjustments.
quickly manufacture customized

products without the need to carry
fixed finished goods inventory.
This minimizes time-to-customer
and cost-to-customer concerns.
III


Series RDH
Customer Service Locations
Customer Service Locations

Atlanta, GA
Enfield, CT
Corona, CA
Plymouth, MI
Goodland, IN
California
221 Helicopter Circle
Corona, CA 92880
Tel.: (951) 280-3800
Fax: (951) 280-3808
Fax: (800) 869-9886
Indiana
Goodland Plant
715 South Iroquois Street
Goodland, IN 47948
Tel.: (219) 297-3182
Fax: (800) 328-8120
Connecticut
80 Shaker Road
Enfield, CT 06082
Tel.: (860) 749-2215
Fax: (800) 323-0105
Michigan
900 Plymouth Road
Plymouth, MI 48170
Tel.: (734) 455-1700
Fax: (734) 455-1007
Georgia
1300 Six Flags Road
Lithia Springs, GA 30122
Tel.: (770) 819-3400
Fax: (800) 437-3498
Oregon
29289 Airport Road
Eugene, OR 97402
Tel.: (541) 689-9111
Fax: (541) 688-6771
Fax: (800) 624-7996
Eugene, OR
IV


Series RDH
Table of Contents
Table of Contents
Description
Page
Section A Basic Cylinder Information
2-20
Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Available Mounting Styles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Custom Options and Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Features and Benefits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
Application Checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Mounting Styles and Tips for Applying Them . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
RDH Cylinder Model Code / How to Order . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
Rod End Styles and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Mounting Information for Single Rod Cylinders . . . . . . . . . . . . . . . . . . . . . . .11-19
Mounting Information for Double Rod Cylinders . . . . . . . . . . . . . . . . . . . . . . . . . 20
Section B Cylinder Accessories and Replacement Parts
Section
21-30
Cylinder Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21-24

Spherical Bearing Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 25-26
Linear Alignment Couplers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Style 55 Piston Rod End Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Parts Identification / Torque Tool Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 29
Piston and Rod Seal Kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
31-57
Section C Common Modifications

Water Submersible Option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31-32
Hi Load Piston . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Low Friction Seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34-35
Other Common Modifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
ALS Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37-40
EPS-A Proximity Sensor / CLS-A Limit Switches . . . . . . . . . . . . . . . . . . . . . 41-43
Cylinders with Limit Switches Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . 44-52
Counterbalance Valves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54-57
60-72
Section D Engineering Data
Theoretical Push and Pull Forces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Cylinder Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Seal Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62-63
Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64-65
Stroke Data and Tolerances / Fatigue Life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Mounting Groups and Force Transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Stop Tubing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Piston Rod Selection Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68-69
Cylinder Safety Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70-71
Offer of Sale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
1


Series RDH
Product Specifications
General Specifications
Heavy duty service

Standard construction threaded head, welded cap
Bore diameters 1.50" through 8.00"
Strokes available in any practical stroke length
Piston rod diameters 0.625" through 5.500"
(based on bore size)
Rod end styles 5 standard, specials available
Single rod end or double rod ends
Mounting styles 9 standard styles at various

application ratings
Nominal pressure 3,000 psi1 (207 Bar)
Standard fluid media filtered hydraulic oil 2
Standard temperature -10F to +165F3
RoHS compliant
1
In line with our policy of continuing product improvement,

specifications in this catalog are subject to change.
If hydraulic pressure exceeds 3,000 psi (207 Bar), send

application data for engineering evaluation and recommendation.
See Seal Information pages for appropriate seals with different
fluid media.
See Seal Information pages for lower and higher temperature
service.
Material Specifications Standard Temperatures and Applications
Head
Cap
Cylinder body
Piston rod
Rod seal
Rod wiper seal
Rod bearing
Ductile iron
Carbon steel
Carbon steel
Case-hardened, chrome plated
high strength carbon steel
Polyurethane
Urethane
WearGard
Piston
Piston seal
Piston seal energizer
Piston bearing
Piston fastener
Piston joint o-ring
End seal o-ring
Backup ring
Ductile iron
Polyurethane
Nitrile
WearGard or MolyGard
Carbon steel
Fluorocarbon
Nitrile
Nitrile
Operating Temperature Options Material and Part Changes

High temperatures
(to +250F)
Class 5
Rod seal, rod wiper seal, end

seal, backup ring and piston seal
energizer are fluorocarbon.
Piston seal is bronze filled PTFE.
Extreme high
temperatures
(to +400F)
Class 8
Rod seals, rod wiper seal and

piston seal are bronze filled
PTFE. End seal o-ring, backup
ring and seal energizers are
fluorocarbon. Bearings are
UltraComp CGT.
Low temperatures
(to -50F)
Class 4
Piston seal energizer, end

seal and backup ring are
low temperature rated
nitrile.
Other Standard Options Material and Part Changes

Cylinder seal
options4
(for chemical
compatibility)
Water Base Fluid Seals (Class 2)

EPR Seals (Class 3)
Fluorocarbon Seals (Class 5)
HWCF Seals (Class 6)
Mixed-Media Piston Seals
(bronze filled PTFE and nitrile)
Magnetic ring
Sintered NdFeB
Piston rod
material options
17-4 PH stainless steel,

chrome plated
303 and 316 stainless steel are
available at lower operating
pressures; consult factory.
See Seal Information pages for additional specifications.
Private Labeling
If labels with logos are desired, contact the
Industrial Cylinder Division for assistance.
For those discerning customers wanting a personal

touch, we can private label cylinders at no charge.
The information must be in text format (no logos) and
the label must include our serial number and cylinder
pressure rating. Just place an S for special in the
Special Modification field and provide the private label
information in the item notes. We take care of the rest!
YOUR NAME HERE
2


Series RDH
Custom Options and Modifications
Available Mounting Styles

Basic, No Mount
Cap Fixed Eye
Cap Fixed Clevis
Style T
Spherical Bearing Cap End
Style B
Round Head Flange
Style J
Style JP
with close
tolerance pilot
Intermediate Fixed Trunnion
Crosstube Cap End
Style SB/SBM
Style BB
Style TT
Style DD
Double Rod Cylinders
Round Cap Flange
Style KT Shown
Style H
Mounting styles
T, DD and J are available
as double rod cylinders.
Custom Options and Modifications (consult factory)

Special Heads, Caps, Pistons and Mounts

Mount/Port Relocation

Oversize/Undersize Ports
Port Thread Styles
Port Blocks/Valve Manifold and Flow Tubing
(at either end)
Multiple Ports
Cartridge Valves
Air Bleeds
Double Rod End
Oversize/Undersize Rod Diameters
Extra Thick Chrome Plated Piston Rod
Rod Materials (stainless steels, alloy steels, etc.)
Rod Coatings (laser-clad, nanoplating, etc.)
Nitrided Rod
Pinned Rod to Piston
Welded Rod to Piston
Welded Rod End Accessory
Extra Wrench Flats
Rod Boot
Parker Crown Wiper
(Extreme Duty Non-Metallic Rod Wiper)
Metallic Rod Wiper
Seal Materials (additional compounds)
PolyPak Seals
Stop Tube
Stroke Adjuster
Point Feedback ALS Switch
(PNP/NPN Mid-Stroke Switch)
Point Feedback CLS-A Switch
(Magnetically-Actuated End-Of-Stroke Limit Switch)
Point Feedback EPS-A Sensor
(PNP End-Of-Stroke Proximity Sensor)
Continuous Linear Position Feedback
Linear Displacement Transducer (LDT)
Fixed Cushions
High Pressure Service (>3,000 PSI)
Pneumatic Service
Water Submersible Design
Chrome Plated Bore
Nickel Plated Assembly
Application-Specific Paint (Marine-Grade, Salt-Spray
Rated, Caustic Washdown, etc.)
Stainless Steel Construction (derated operating
pressure)
Metric Rod and Bore Diameters
Dual End Seals

Features and Benefits

Series RDH
The inside story on why

Series RDH is your best choice in
heavy duty roundline cylinders
Optional Extreme Temperature/
Low Friction Seal Assembly
Dual bronze filled PTFE rod seals
and bronze filled PTFE wiper seal are
energized with fluorocarbon o-rings to
maintain consistent contact with the
piston rod.
The result is excellent sealing
performance with low friction. Our seal
set provides a dry rod surface on
the extend stroke with rod scraping
to clean the rod on the retract stroke.
Heat resistance to 400F with the
Class 8 Seals option. For additional
Primary Seal Polyurethane Tri-Lip

Rod Seal is a proven leakproof design
completely self-compensating and
self-relieving to withstand variations
and conform to mechanical deflection
that may occur.
details, see the Low Friction Seals

page and Class 8 Seals specifications
on the Seal Information page.
Ports Seal-welded to the cylinder

body. SAE straight thread o-ring ports
are standard. Other port styles (NPTF,
BSPP, BSPT, etc.) are also available.
End Seal Parker o-ring with backup

ring located on a smooth bore to
combine leak-free service with an antiextrusion design.
Secondary Seal Dual-Service

Urethane Wiperseal wipes clean
any oil film adhering to the rod on the
extend stroke and removes external
debris and adherents from the rod on
the return stroke.
Piston Rod Induction casehardened, hard chrome-plated medium
carbon steel, polished to an optimum
finish. Piston rods are made from
100,000 psi minimum yield material for
.625" through 4.000" diameters and
70,000 psi minimum yield material for
larger diameters. Stainless steel is
available as an option.
Ductile Iron Head Concentric with

the bore, it acts as the high-strength
rod guide and housing for the rod seal,
wiper seal and bearing. Torqued to
the cylinder body for lasting cylinder
integrity.
Composite Wear Rings Parker

WearGard wear rings are internally
lubricated for reduced friction and
formulated for heavy-duty, load-bearing
applications.
Buttress Threads The strongest

commercial thread style for pressure
vessels with axial and impact loading.

Features and Benefits

Series RDH
Steel Cap and Mount Concentric
with the bore and arc-welded for
tough applications.
Piston Fastener Carbon steel,
prevailing-torque type nut 1 for
cylinder serviceability (especially
for welded rod ends).
One-Piece Ductile Iron Piston

The wide piston and bearing are truly
designed for heavy-duty industrial
applications. One-piece design for
strength and product integrity.
Piston Seal Polyurethane
bi-directional seal for long service life.
Energized for leak-free service at any
pressure.
Composite Wear Rings Parker

WearGard wear rings are internally
lubricated for reduced friction and
formulated for heavy-duty, load-bearing
applications.
Cylinder Body Heavy-wall steel

tubing, burnished to a micro finish bore.
Piston Joint Seal Parker o-ring for
positive joint sealing on a smooth rod
diameter.
1
Only for 1.50" to 5.00" bores. For 6.00" to 8.00" bores, pistons are threaded and torqued to the piston rod, and set screws are used to lock
the piston to the rod.
Optional Pistons
Hi Load/Low Friction Piston

Bronze filled PTFE piston seal for
maximum seal life in extreme duty
and side load applications.
Mixed Media Piston Used for

dissimilar fluids or a gas on either
side of the piston (i.e. air/oil
applications).
Magnetic Piston Includes magnetic

rings for the ALS Switch option.


Series RDH
Application Checklist
Application Checklist
The following checklist should be used to select the best possible cylinder for a given application. Additional
information can be referenced in the following pages to help assist in this process. In the event that you have
additional questions or concerns, or if more information is required, contact your local Parker distributor or our
customer service representatives for assistance.
1.

Establish the system requirements

How heavy is the load to be moved?
What is the nominal operating pressure of the system?
How far does the load have to move?
What is the speed at which the load will move?
What is the fluid type and the temperature to which the cylinder will be exposed?
2. Mounting Style.....................................................................................................................................Pages 3 and 7
Determine the best mounting style for the application.

3. Cylinder Bore and Operating Pressure ......................................................................................................Page 60
Review the theoretical push and pull forces to determine the applicable bore and rod diameter sizes.
4. Piston Rod .............................................................................................................................................. Pages 66-69
Determine what rod size will be required to avoid buckling.

Determine if a single or double rod cylinder is required.
Determine the rod end style and rod end thread.
Will stop tubing be required?
Is adequate pull force still available or is a larger bore diameter now required?
5. Seals........................................................................................................................................................ Pages 62-63
Select the proper seal type and configuration for the application.
Select the proper seal to assure fluid and temperature compatibility.
6. Ports.......................................................................................................................................................... Page 64-65
Select the best possible port size for a given speed requirement.
Select port type.
Select port position.
7. Piston rod and mounting accessories.................................................................................................Pages 21-28
Determine how you will attach the cylinder to the load.

8. Optional accessories and modifications ............................................................................................Pages 31-57


Series RDH
Mounting Style Tips
Mounting Styles and Tips for Applying Them

Pivot Mountings B, BB, SB/SBM and TT
Application:
Curved or arc line force
transfer
Can be used in compression or
tension loads
Movement in a simple arc
use B, BB or TT mounts
Movement in a compound arc
use SB/SBM mount
Advantages:
Ease of mounting
Design flexibility
Self aligning (SB/SBM mount)
Trunnion Mountings DD
Application:
Curved or arc line force
transfer
Can be used in compression or
tension loads
Advantages:
Ease of mounting
Design flexibility
Improved cylinder weight
support
Reduces piston and rod
bearing loads
Flange Mountings J/JP and H

Application:
Straight line force transfer
Compression loads (push)
use H mount
Tension loads (pull)
use J/JP mount
Advantages:
Ease of mounting
Rigid base mounting due to
large flange area
JP Mount pilot improves
alignment of cylinder and load


Series RDH
How To Order
Series RDH Model Code

2.00
Bore
Diameter
Specify
bore dia.
in inches
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Double
Rod End
Cylinder
Specify
K only if
Double
Rod
Cylinder is
required.1
BB
RDH
Mounting
Style
Series
Piston
Ports
T=
U=
R=
P=
B=
RDH
T
B
BB
SB
=
=
=
=
SBM =
TT =
DD =
J=
JP =
H=
Basic, No Mount
Cap Fixed Eye
Cap Fixed Clevis
Spherical Bearing
Cap End
Spherical Bearing
Cap End, Metric
(3,000 psi rating)
Crosstube Cap
End
Intermediate
Fixed Trunnion2
Round Head
Flange
Round Head
Flange with Pilot
Round Cap
Flange
Shaded boxes identify the required model number fields.

Available standard mounting styles for K-type cylinders are T,
DD and J/JP. When ordering a double rod cylinder, the piston rod
number and piston rod thread style must be specified for both
rod ends. The model number should be created as viewing the
primary rod end on the left-hand side.
Example of a K-type cylinder:
4.00KDDRDHBT14A28A10.000
2
6
7
8
Standard (SAE)
NPTF
BSPP (ISO 228)
Flange (SAE code 61)
BSPT
B = Standard
(Standard Seal
with Wear Ring)
K = Bronze Filled PTFE
Seal with Wear Ring
F = Low Friction
Cylinder (All Seals)3
7 = Magnetic4
(Standard Seal
with Wear Ring
and Magnet)
W = Mixed Media5
(Mixed Media Seal
with Wear Ring)
Specify XI dimension. See minimum and maximum XI dimensions on DD Intermediate Fixed Trunnion Mounting Page.
Includes low friction seals for the entire cylinder. Available with
standard seals and Seal codes 2, X, 4, V and H.
Used with externally mounted ALS Switches. Includes seal
and wear ring from standard piston. Available for 1.50" to 6.00"
bore diameters. Switch operating temperature range is -13F to
+185F. Switch position may be restricted for Mounting Style DD.
Consult factory for other options.
Used for dissimilar fluids or a gas on either side of the piston
(i.e. air/oil applications). Standard mixed media piston
accommodates fluids which are compatible with Class 1 Seals.
See Seal Information pages for more details. For other fluids,
consult factory.
See Seal Information pages for additional information.
Option used for Piston code 7 (Magnetic Piston).
Used for external chemical compatibility applications, not high
temperature.
8
Seals6
Blank = Standard
(Polyurethane,
Class 1)
2 = Water Base
Fluid/HWCF
Seals (Classes 2
and 6)
X = EPR Seals
(Class 3)
4 = Low
Temperature
Seals (Class 4)

V = Fluorocarbon

Seals (Class 5)
H = Extreme High
Temperature
Seals (Class 8)
K = Class 1 Seals
with Bronze
Filled PTFE
Piston Seal7
E = Fluorocarbon
Rod Seal and
Wiper Only8
M = Metallic Rod
Wiper, Standard
Seals
D = Metallic Rod
Wiper, Fluorocarbon Seals


Series RDH
How To Order
Series RDH Model Code

1
Special
Modification
Piston Rod
Number 9
Piston Rod
End
Specify "S"
for special
modification
other than rod
end, and then
describe the
modification in
the item notes.
1
2
3
4
5
4 = Style 4 Small
Male
7 = Style 7 Thread
for Spherical
Rod Eye10
8 = Style 8
Intermediate
Male
9 = Style 9 Small
Female10
55 = Style 55 For
Flange
Coupling
3 = Style 3 Special
(specify)11
6.000
Piston Rod
Material12
Piston Rod
Threads
Stroke14
Blank = Standard
Y = 17-4 PH
Stainless
Steel 12
A = Standard
(UNF)
M = Metric13
N = No Threads
(only used
for Style 55
or Style 3
rod ends)
Specify in
inches (see
Minimum
Standard
Stroke table
below)
Minimum Standard Stroke

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
MM
Rod
DD
Mount
With Style 9 or 7A Rod End

and Standard W Dimension
1
2
1
2
1
2
3
1
2
3
1
2
3
1
2
3
4
1
2
3
4
1
2
3
4
5
1
2
3
4
5
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
3.03
3.03
3.12
3.12
2.98
2.98
2.98
3.61
3.61
3.61
3.52
3.52
3.52
3.88
3.88
3.88
3.88
4.46
4.46
4.46
4.46
5.10
5.10
5.10
5.10
5.10
5.54
5.54
5.54
5.54
5.54
J Mount All Other Mounts

No Min.
No Min.
No Min.
No Min.
No Min.
No Min.
No Min.
0.25
No Min.
No Min.
No Min.
0.44
No Min.
No Min.
No Min.
No Min.
No Min.
0.65
No Min.
0.19
No Min.
No Min.
1.19
1.94
No Min.
0.40
No Min.
0.15
1.29
2.04
0.43
1.18
1.08
1.83
0.49
1.24
2.26
3.01
1.14
1.89
1.35
2.10
0.95
1.95
3.36
4.36
1.16
2.16
2.07
3.07
2.65
3.65
0.94
1.94
4.06
5.06
1.86
2.86
2.44
3.44
3.15
4.15
Shaded boxes identify the required model number fields.

9
Refer to the Stop Tubing and Piston Rod Selection Data
pages to assure that the selected rod number will not
buckle under load.
10
Style 7A (UNF threads) and Style 9 may require a minimum
stroke. See Minimum Standard Stroke in table to the left for
details.
11
Provide desired dimensions for KK (or CC), A and W.
If otherwise special, supply a dimensioned sketch.
Accessories welded to the rod end are available.
12
Other stainless steels (i.e. 303, 316) are available with a
derated maximum operating pressure; consult factory.
13
For Style 7M, see page 15 for details. For Styles 4M, 8M
and 9M, see page 36 for details.
14
If a stop tube is required, specify gross stroke (net stroke
+ stop tube length) in the model number field, then place
an S for special in the Special Modification field and
specify the stop tube length in the item notes. For stroke
length tolerance, see Stroke Data page.


Series RDH
Rod End Styles and Dimensions

Rod End Dimensions
Thread Style 4
(NFPA Style SM)
Small Male
A
Thread Style 8
(NFPA Style IM)
Intermediate Male
A
Thread Style 91
(NFPA Style SF)
Small Female
Style 55 2
Flanged Rod End
WG
R.06
MM
KK
NA
CC
D
WRENCH
FLATS
MM
MM
AD
NA
D
WRENCH
FLATS
D
WRENCH
FLATS
AF
AE
KK
NA
MM
AM
Rod End Dimensions

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
MM
Rod
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
Thread
Style
Style
8
4&9
CC
KK
1/2-20 7/16-20
7/8-14
3/4-16
7/8-14
3/4-16
1 1/4-12
1-14
7/8-14
3/4-16
1 1/2-12 1 1/4-12
1 1/4-12
1-14
1 1/4-12
1-14
1 3/4-12 1 1/2-12
1 1/2-12 1 1/4-12
1 1/2-12 1 1/4-12
2 1/4-12 1 7/8-12
1 3/4-12 1 1/2-12
1 3/4-12 1 1/2-12
3 1/4-12 2 1/2-12
2 1/4-12 1 7/8-12
2 3/4-12 2 1/4-12
2 1/4-12 1 7/8-12
3 3/4-12
3-12
2 3/4-12 2 1/4-12
3 1/4-12 2.1/2-12
2 3/4-12 2 1/4-12
4 3/4-12 3 1/2-12
3 1/4-12 2 1/2-12
3 3/4-12
3-12
4 1/4-12 3 1/4-12
3 1/4-12 2 1/2-12
5 1/4-12
4-12
3 3/4-12
3-12
4 1/4-12 3 1/4-12
4 3/4-12 3 1/2-12
AD
AE
+.001
-.001
AF
AM
NA
WG
0.75
1.13
1.13
1.63
1.13
2.00
1.63
1.63
2.25
2.00
2.00
3.00
2.25
2.25
3.50
3.00
3.50
3.00
4.00
3.50
3.50
3.50
5.00
3.50
4.00
4.50
3.50
5.50
4.00
4.50
5.00
0.63
0.94
0.94
1.06
0.94
1.31
1.06
1.06
1.69
1.31
1.31
1.94
1.69
1.69
2.69
1.94
2.44
1.94
2.69
2.44
2.69
2.44
3.19
2.69
2.69
3.19
2.69
3.94
2.69
3.19
3.19
0.249
0.374
0.374
0.374
0.374
0.499
0.374
0.374
0.624
0.499
0.499
0.749
0.624
0.624
0.999
0.749
0.874
0.749
0.999
0.874
0.999
0.874
1.499
0.999
0.999
1.499
0.999
1.874
0.999
1.499
1.499
0.38
0.69
0.69
0.88
0.69
1.13
0.88
0.88
1.38
1.13
1.13
1.75
1.38
1.38
2.50
1.75
2.25
1.75
3.00
2.25
2.50
2.25
3.88
2.50
3.00
3.50
2.50
4.38
3.00
3.50
3.88
0.57
0.95
0.95
1.32
0.95
1.70
1.32
1.32
1.95
1.70
1.70
2.45
1.95
1.95
3.45
2.45
2.95
2.45
3.95
2.95
3.45
2.95
4.95
3.45
3.95
4.45
3.45
5.45
3.95
4.45
4.95
0.50
0.88
0.88
1.13
0.88
1.50
1.13
1.13
1.69
1.50
1.50
2.06
1.69
1.69
3.00
2.06
2.63
2.06
3.38
2.63
3.00
2.63
3
3.00
3.38
3
3.00
3
3.38
3
3
0.56
0.94
0.94
1.31
0.94
1.69
1.31
1.31
1.94
1.69
1.69
2.38
1.94
1.94
3.38
2.38
2.88
2.38
3.88
2.88
3.38
2.88
4.88
3.38
3.88
4.38
3.38
5.38
3.88
4.38
4.88
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
1.13
1.50
1.50
1.75
1.50
2.00
1.75
1.75
2.63
2.00
2.00
3.25
2.63
2.63
4.38
3.25
3.63
3.25
4.50
3.63
4.38
3.63
5.38
4.38
4.50
5.25
4.38
6.25
4.50
5.25
5.38
Special Thread Style 3

Special thread, extension, rod eye, blank, welded rod end
accessory, etc. are also available.
Style 9 stroke restrictions may apply. See Minimum Stroke for

Style 9 Rod End in table on How To Order page for details.
2
For any special Style 55 dimensions, specify Style 3 and provide
the desired dimensions for AD, AE, AF, AM and WG. For other
changes, specify S in the model code, and describe the rod end
with a dimensioned sketch.
3
These piston rods have four 0.515" dia. x 0.5" deep spanner
wrench holes instead of wrench flats on diameter NA.
1
To order, specify Style 3 and give desired dimensions for KK,

A, W or WF. If otherwise special, furnish dimensioned sketch.
10

Mounting Information 1.50" to 8.00" Bore

Basic, No Mount
Style T

Series RDH
ZJ + STROKE
P + STROKE
EE
E
HD
MM
Table 1 Dimensional and Mounting Data

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
1 (std)
2
All
All
All
All
All
All
All
All
1.88
1.88
2.38
3.00
3.88
4.61
5.75
7.00
8.00
9.25
LB + STROKE
EE
HD
SAE2
6
6
8
8
12
12
12
16
20
20
NPTF1
3/8
3/8
1/2
1/2
3/4
3/4
3/4
1
1 1/4
1 1/4
NPTF ports are available for no additional charge

1
1.60
1.60
2.04
2.37
2.81
3.20
3.79
4.58
5.11
5.76
Add Stroke
LB
3.56
3.94
4.81
5.25
6.00
6.50
7.12
8.37
9.00
9.50
P
1.19
1.19
1.93
1.88
2.06
2.50
2.56
3.00
3.25
3.25
SAE straight thread o-ring ports are standard

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
MM Rod
Add Stroke
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.06
3.25
3.19
3.40
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
ZJ
4.12
4.63
5.50
5.62
5.94
6.19
6.06
6.81
7.00
6.94
7.44
7.56
7.50
8.12
8.18
8.18
8.18
9.43
9.43
9.43
9.43
10.06
10.19
10.06
10.06
10.19
10.56
10.68
10.56
10.68
10.68
11


Series RDH

Cap Fixed Eye Mounting
Style B
ZC + STROKE
XC + STROKE
P + STROKE
EE
CD
HOLE DIA.
E
HD
MM
W
LR
L
M
LB + STROKE

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
1 (std)
2
All
All
All
All
All
All
All
All
CB
0.75
0.75
1.25
1.25
1.50
2.00
2.50
2.50
3.00
3.00
CD
+.002
-.000
0.502
0.502
0.752
0.752
1.002
1.377
1.752
2.002
2.502
3.002
1.88
1.88
2.38
3.00
3.88
4.61
5.75
7.00
8.00
9.25

1
CB
EE
HD
NPTF
SAE
3/8
3/8
1/2
1/2
3/4
3/4
3/4
1
1 1/4
1 1/4
6
6
8
8
12
12
12
16
20
20
1.60
1.60
2.04
2.37
2.81
3.20
3.79
4.58
5.11
5.76
0.75
0.75
1.25
1.25
1.50
2.13
2.25
2.50
3.00
3.25
LR
min.
0.56
0.56
0.88
0.88
1.13
1.81
1.88
2.13
2.63
3.00
0.50
0.50
0.75
0.75
1.00
1.38
1.75
2.00
2.50
2.75
Add Stroke
LB
3.56
3.94
4.81
5.25
6.00
6.50
7.12
8.37
9.00
9.50
1.19
1.19
1.93
1.88
2.06
2.50
2.56
3.00
3.25
3.25

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
Y
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.06
3.25
3.19
3.40
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
Add Stroke
XC
4.87
5.38
6.75
6.87
7.19
7.44
7.31
8.31
8.50
8.44
9.56
9.69
9.62
10.37
10.43
10.43
10.43
11.93
11.93
11.93
11.93
13.06
13.19
13.06
13.06
13.09
13.81
13.93
13.81
13.93
13.93
12
ZC
5.37
5.88
7.50
7.62
7.94
8.19
8.06
9.31
9.50
9.44
10.94
11.06
11.00
12.12
12.18
12.18
12.18
13.93
13.93
13.93
13.93
15.56
15.69
15.56
15.56
15.69
16.56
16.68
16.56
16.68
16.68

Series RDH

Cap Fixed Clevis Mounting
Style BB
ZC + STROKE
XC + STROKE
P + STROKE
CD
PIN DIA.
E
EE
HD
MM
LR

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
1 (std)
2
All
All
All
All
All
All
All
All
CB
min.
CD1
+.000
-.002
CW
0.77
0.77
1.09
1.28
1.53
2.06
2.56
2.56
3.06
3.06
.501
.501
.751
.751
1.001
1.376
1.751
2.001
2.501
3.001
0.50
0.50
0.50
0.63
0.75
1.00
1.25
1.25
1.50
1.50
LB + STROKE
1.88
1.88
2.38
3.00
3.88
4.61
5.75
7.00
8.00
9.25
EE
HD
NPTF2
SAE 3
3/8
3/8
1/2
1/2
3/4
3/4
3/4
1
1 1/4
1 1/4
6
6
8
8
12
12
12
16
20
20
1.60
1.60
2.04
2.37
2.81
3.20
3.79
4.58
5.11
5.76
L
0.75
0.75
1.25
1.25
1.50
2.13
2.25
2.50
3.00
3.25
CW
CW
CB
LR
min.
0.56
0.56
0.88
0.88
1.13
1.81
1.88
2.13
2.63
3.00
0.50
0.50
0.75
0.75
1.00
1.38
1.75
2.00
2.50
2.75
Add Stroke
LB
3.56
3.94
4.81
5.25
6.00
6.50
7.12
8.37
9.00
9.50
1.19
1.19
1.93
1.88
2.06
2.50
2.56
3.00
3.25
3.25
Diameter CD is the Pivot Pin diameter (included) 2 NPTF ports are available for no additional charge
3

1

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
Y
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.06
3.25
3.19
3.40
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
Add Stroke
XC
4.87
5.38
6.75
6.87
7.19
7.44
7.31
8.31
8.50
8.44
9.56
9.69
9.62
10.37
10.43
10.43
10.43
11.93
11.93
11.93
11.93
13.06
13.19
13.06
13.06
13.19
13.81
13.93
13.81
13.93
13.93
13
ZC
5.37
5.88
7.50
7.62
7.94
8.19
8.06
9.31
9.50
9.44
10.94
11.06
11.00
12.12
12.18
12.18
12.18
13.93
13.93
13.93
13.93
15.56
15.69
15.56
15.56
15.69
16.56
16.68
16.56
16.68
16.68

Series RDH

Spherical Bearing Cap End Mounting
Inch Size Bearing
Note: Standard spherical
Style SB
ZC + STROKE
XC + STROKE
P + STROKE
EE
bearing is maintenance-free
(sealed) for hole diameters
larger than 0.5000".
Note: Female threaded rod

end is shown to accept the
inch-size spherical rod eye
accessory with a male
thread.
NR
E
CD
HOLE DIA.
HD
MM
W
A
KK
LB + STROKE
MA
EX
CB

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
Rod No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
Thread
CB
Style 9A Style 7A
KK1
KK1
7/16-20
3/4-16
3/4-16
1-14
1 1/4-12
1 1/2-12
1 7/8-12
7/16-20
3/4-16
3/4-16
3/4-16
1-14
1-14
1 1/4-12
1 1/4-12
1 1/2-12
1 1/2-12
1 1/2-12
1 7/8-12
1 7/8-12
1 7/8-12
0.75
0.75
1.13
1.13
1.13
1.13
1.13
1.63
1.63
1.63
2.00
2.00
2.00
2.25
2.25
2.25
2.25
3.00
3.00
3.00
3.00
7.00
8.00
CD2
+.0000
-.0005
MA
NR
min.
0.38 0.5000 0.44
0.75
0.75
0.56
0.56 0.7500 0.66
1.25
1.00
1.06
0.56 0.7500 0.66
1.25
1.00
1.06
0.75 1.0000 0.88
1.50
1.25
1.31
1.00 1.3750
1.19
2.13
1.88
1.88
1.25 1.7500 1.53
2.25
2.50
1.94
1.50 2.0000 1.75
2.50
2.50
2.19
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.06
3.25
3.19
3.40
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
Add Stroke
XC
ZC
4.87
5.38
6.75
6.87
7.19
7.44
7.31
8.31
8.50
8.44
9.56
9.69
9.62
10.37
10.43
10.43
10.43
11.93
11.93
11.93
11.93
5.62
6.13
7.75
7.87
8.19
8.44
8.31
9.56
9.75
9.69
11.44
11.56
11.50
12.87
12.93
12.93
12.93
14.43
14.43
14.43
14.43
See SBM Mount on the next page
Note: for additional dimensions see Style BB mount.

1
These thread dimensions match mating thread dimensions of an inchsize spherical rod eye with the same hole diameter as the cap end.
It must be purchased separately; see Spherical Bearing Mounting
Accessories page for detailed information.
Table 2 Recommended maximum swivel

angle on each side of the cylinder centerline.
Bore Head End Mounted
1.50
2.00
2.50
3.25
4.00
5.00
6.00
EX
Dimension CD is the hole diameter.
SB Pressure Ratings
Mounting Information
Head End Mounting
Cap End Mounted
Angle a
Tan. of a
Angle a
Tan. of a
2.00
2.50
2.50
3.00
2.50
3.00
3.00
0.035
0.044
0.044
0.052
0.044
0.052
0.052
2.00
4.50
4.50
3.00
3.00
3.00
3.00
0.035
0.079
0.079
0.052
0.052
0.052
0.052
X
XL + STROKE
Cap End Mounting

X
4
A
XL + STROKE
Note: Dimension X is the maximum off-center mounting of the

cylinder. To determine dimension X for various stroke lengths, 3
See Spherical Bearing Mounting Accessories
multiply the distance between pivot pin holes by tangent of
pages for information on mounting accessories.
angle a. For extended position use XL + 2 x STROKE.
14
Bore
Maximum
Operating
Pressure
(psi) 4
1.50
2.00
2.50
3.25
4.00
5.00
6.00
1,500
2,200
1,450
1,500
1,850
2,000
1,800
Pressure ratings are based

on standard commercial
bearing ratings. For
spherical bearing mount
rated to 3,000 psi, see the
SBM Mount on the next
page.


Series RDH
Spherical Bearing Cap End Mounting

Metric Size Bearing
Style SBM
Note: Standard spherical
bearing is maintenancefree (sealed).
ZC + STROKE
XC + STROKE
P + STROKE
EE
Note: Male threaded rod end

is shown to accept the metric
spherical rod eye accessory
with a female thread.
NR
E
CD
HOLE DIA.
MM
KK
MA
Although the standard SB Mount has derated pressure

ratings below 3,000 psi, the SBM Mount is a standard
spherical bearing mount rated at 3,000 psi. Note that
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
Rod
Thread
Length
(mm)
Thread
Style 7M
Male
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
0.71 (18)
0.71 (18)
0.87 (22)
0.87 (22)
1.10 (28)
1.10 (28)
1.10 (28)
1.42 (36)
1.42 (36)
1.42 (36)
1.77 (45)
1.77 (45)
1.77 (45)
2.20 (56)
2.20 (56)
2.20 (56)
2.20 (56)
2.48 (63)
2.48 (63)
2.48 (63)
2.48 (63)
3.35 (85)
3.35 (85)
3.35 (85)
3.35 (85)
3.35 (85)
3.35 (85)
3.35 (85)
3.35 (85)
3.35 (85)
3.35 (85)
M14X1.5
M14X1.5
M16X1.5
M16X1.5
M20X1.5
M20X1.5
M20X1.5
M27X2
M27X2
M27X2
M33X2
M33X2
M33X2
M42X2
M42X2
M42X2
M42X2
M48X2
M48X2
M48X2
M48X2
M64X3
M64X3
M64X3
M64X3
M64X3
M64X3
M64X3
M64X3
M64X3
M64X3
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
EX
LB + STROKE

Bore Rod No. MM
A1
KK1
W
HD
CB
the SBM Mount has slightly different lug dimensions and

a metric bearing size. See Spherical Bearing Mounting
Accessories page for metric size accessories.
Add Stroke
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.06
3.25
3.19
3.40
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
Note: for additional dimensions, see Style SB Mount.

For recommended maximum swivel angles, see Table 2 and sketch
on the previous page.
1
These thread dimensions match mating thread dimensions of a
metric spherical rod eye with the same hole diameter as the cap
end. It must be purchased separately; see Spherical Bearing
Mounting Accessories page for metric sizes for detailed information.
XC
ZC
5.11
5.61
6.72
6.84
7.43
7.68
7.56
8.70
8.89
8.83
9.72
9.84
9.78
10.95
11.01
11.01
11.01
13.05
13.05
13.05
13.05
14.63
14.75
14.63
14.63
14.75
15.12
15.25
15.12
15.25
15.25
6.25
6.75
8.02
8.14
9.01
9.26
9.13
10.67
10.86
10.80
12.16
12.28
12.22
14.10
14.16
14.16
14.16
16.99
16.99
16.99
16.99
19.35
19.47
19.35
19.35
19.47
19.85
19.97
19.85
19.97
19.97
Dimensions at cap end (mm)

CB
(mm)
CD2
(mm)
EX
L
MA NR min.
(mm) (mm) (mm) (mm)
0.51 0.7874 -.0005 0.63 0.98 1.14

(13)
(20 -.012)
(16) (25) (29)
0.87
(22)
0.67 0.9843 -.0005 0.79 1.22 1.30

(17)
(25 -.012)
(20) (31) (33)
1.10
(28)
0.75 1.1811 -.0005 0.87 1.50 1.57

(19)
(30 -.012)
(22) (38) (40)
1.38
(35)
0.91 1.5748 -.0005 1.10 1.89 1.97

(23)
(40 -.012)
(28) (48) (50)
1.73
(44)
1.18 1.9685 -.0005 1.38 2.28 2.44

(30)
(50 -.012)
(35) (58) (62)
2.13
(54)
1.50 2.3622 -.0006 1.73 2.83 3.15

(38)
(60 -.015)
(44) (72) (80)
2.68
(68)
1.85 3.1496 -.0006 2.17 3.62 3.94

(47)
(80 -.015)
(55) (92) (100)
3.46
(88)
2.24 3.9370 -.0008 2.76 4.57 4.72

(57)
(100 -.020)
(70) (116) (120)
4.37
(111)
2.24 3.9370 -.0008 2.76 4.57 4.72

(57)
(100 -.020)
(70) (116) (120)
4.37
(111)
Dimension CD is the hole diameter.
15


Series RDH

Crosstube Cap End Mounting
Style TT
ZC + STROKE
XC + STROKE
P + STROKE
EE
CD
HOLE DIA.
E
HD
PT
MM

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
1 (std)
2
All
All
All
All
All
All
All
All
CD
+.002
-.000
0.752
0.752
0.752
1.002
1.252
1.377
1.752
2.002
2.502
3.002
1.88
1.88
2.38
3.00
3.88
4.61
5.75
7.00
8.00
9.25
LB + STROKE
EE

1
HD
NPTF1
SAE2
3/8
3/8
1/2
1/2
3/4
3/4
3/4
1
1 1/4
1 1/4
6
6
8
8
12
12
12
16
20
20
1.60
1.60
2.04
2.37
2.81
3.20
3.79
4.58
5.11
5.76
0.63
0.63
0.63
0.75
0.94
1.00
1.38
1.50
1.88
2.00
LT
2.38
2.38
2.88
3.50
4.38
5.13
6.25
7.50
8.50
9.75
LT
PT
1.25
1.25
1.25
1.50
1.88
2.00
2.75
3.00
3.75
4.00
Add Stroke
LB
3.56
3.94
4.81
5.25
6.00
6.50
7.12
8.37
9.00
9.50
1.19
1.19
1.93
1.88
2.06
2.50
2.56
3.00
3.25
3.25

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
MM Rod
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
Y
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.06
3.25
3.19
3.40
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
Add Stroke
XC
4.75
5.25
6.13
6.25
6.69
6.94
6.81
7.75
7.94
7.88
8.44
8.56
8.50
9.49
9.55
9.55
9.55
10.93
10.93
10.93
10.93
11.94
12.06
11.94
11.94
12.06
12.56
12.68
12.56
12.68
12.68
16
ZC
5.37
5.88
6.75
6.87
7.44
7.69
7.56
8.69
8.88
8.81
9.44
9.56
9.50
10.87
10.93
10.93
10.93
12.43
12.43
12.43
12.43
13.81
13.94
13.81
13.81
13.94
14.56
14.68
14.56
14.68
14.68

Series RDH

Intermediate Fixed Trunnion Mounting
Style DD
ZJ + STROKE
P + STROKE
EE
BD
UM
UX
R.125 MAX
HD
TD
MM
W
TL
TM

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
1
Rod
No.
BD
1 (std)
2
All
All
All
All
All
All
All
All
1.31
1.31
1.69
1.69
2.19
2.44
2.88
3.38
3.88
4.44
1.88
1.88
2.38
3.00
3.88
4.61
5.75
7.00
8.00
9.25
EE
HD
NPTF1
SAE2
3/8
3/8
1/2
1/2
3/4
3/4
3/4
1
1 1/4
1 1/4
6
6
8
8
12
12
12
16
20
20
XI
TL
1.60
1.60
2.04
2.37
2.81
3.20
3.79
4.58
5.11
5.76
LB + STROKE
TD
+.000
-.001
TL
1.000
1.000
1.375
1.375
1.750
2.000
2.500
3.000
3.5003
4.0003
1.00
1.00
1.38
1.38
1.75
1.75
1.75
2.00
2.50
3.00
TM
3.00
3.00
3.50
4.00
5.00
5.50
7.00
8.50
9.75
11.00
UM
5.00
5.00
6.25
6.75
8.50
9.00
10.50
12.50
14.75
17.00
3
UX
3.00
3.00
3.50
4.00
5.00
6.00
7.38
9.00
10.25
11.75
Add Stroke
LB
3.56
3.94
4.81
5.25
6.00
6.50
7.12
8.37
9.00
9.50
1.19
1.19
1.93
1.88
2.06
2.50
2.56
3.00
3.25
3.25
Tolerance is +.000/-.002

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
MM
Rod
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.06
3.25
3.19
3.40
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
Min.
Stroke4
Min.
XI5
3.03
3.03
3.12
3.12
2.98
2.98
2.98
3.61
3.61
3.61
3.52
3.52
3.52
3.88
3.88
3.88
3.88
4.46
4.46
4.46
4.46
5.10
5.10
5.10
5.10
5.10
5.54
5.54
5.54
5.54
5.54
4.25
4.75
4.95
5.07
5.13
5.38
5.25
5.87
6.06
6.00
6.33
6.46
6.40
6.89
6.95
6.95
6.95
7.87
7.87
7.87
7.87
8.38
8.51
8.38
8.38
8.51
8.81
8.94
8.81
8.94
8.94
Add Stroke
Max.
XI6
1.19
1.69
2.00
2.12
2.13
2.38
2.25
2.31
2.50
2.44
2.96
3.08
3.02
3.07
3.13
3.13
3.13
3.62
3.62
3.62
3.62
3.38
3.51
3.38
3.38
3.51
3.31
3.44
3.31
3.44
3.44
ZJ
4.12
4.63
5.50
5.62
5.94
6.19
6.06
6.81
7.00
6.94
7.44
7.56
7.50
8.12
8.18
8.18
8.18
9.43
9.43
9.43
9.43
10.06
10.19
10.06
10.06
10.19
10.56
10.68
10.56
10.68
10.68
17
Shorter net/working strokes are available with the

use of a stop tube; however, the overall length of the
cylinder will increase. To achieve a net/working
stroke that is less than the minimum shown, specify
the stop tube length as the minimum stroke in Table 2.
Gross stroke (designated in the model code) will be
the combination of the stop tube length and net
(working) stroke length. If shortest total cylinder length
is required and a stop tube is unacceptable, consult
the factory.
5
Cylinders with an XI dimension shorter than the
standard minimum are available with a special
modification; consult the factory.
6
Add this number to the stroke to determine the
maximum allowable XI dimension with the standard
rod extension (W dimension).
4


Series RDH

Round Head Flange Mounting
Style J
Style JP with close tolerance pilot
FD 2.5
E
WF
WT
W
FC
ZG + STROKE
P + STROKE
EE
YF
HD
RD
MM
UC
FB EQUALLY
SPACED ON FC
1.50"-6.00" BORE 6X FB
7.00"-8.00" BORE 8X FB

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
1.88
2.38
3.00
3.88
4.61
5.75
7.00
8.00
9.25
EE
NPTF1
SAE2
3/8
1/2
1/2
3/4
3/4
3/4
1
1 1/4
1 1/4
6
8
8
12
12
12
16
20
20
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.00
1.13
FB
FC
FD
0.28
0.34
0.41
0.53
0.66
0.78
0.91
0.91
1.06
2.75
3.31
4.13
5.25
6.25
7.50
9.13
10.13
11.63
30
30
30
30
30
30
30
22.5
22.5

1
RT
HD
RD
Style J
1.60
2.04
2.37
2.81
3.20
3.79
4.58
5.11
5.76
LG + STROKE
1.88
2.38
3.00
3.88
4.61
5.75
6.99
7.99
9.24
Style JP
+.000 / -.002
1.810
2.310
2.936
3.810
4.560
5.686
6.936
7.936
9.186
UC
3.38
4.00
5.00
6.38
7.63
9.00
10.94
11.94
13.75
Add Stroke
LG
3.94
5.31
5.75
6.50
7.00
7.55
8.75
9.63
10.00
1.19
1.93
1.88
2.06
2.50
2.56
3.00
3.25
3.25

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
RT
WF
WT
YF
Add Stroke
ZG
0.25
0.63
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.31
0.31
0.31
0.31
0.38
0.38
0.38
0.38
0.38
0.38
0.38
0.38
0.38
0.50
0.50
0.50
0.50
0.50
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
1.19
1.69
1.38
1.50
1.44
1.69
1.56
1.69
1.88
1.81
1.94
2.06
2.00
2.19
2.25
2.25
2.25
2.44
2.44
2.44
2.44
2.44
2.56
2.44
2.44
2.56
2.69
2.81
2.69
2.81
2.81
0.81
1.31
0.94
1.06
0.94
1.19
1.06
1.06
1.25
1.19
1.19
1.31
1.25
1.31
1.37
1.37
1.37
1.44
1.44
1.44
1.44
1.44
1.56
1.44
1.44
1.56
1.56
1.69
1.56
1.69
1.69
2.75
3.25
3.26
3.38
3.44
3.69
3.56
3.82
4.00
3.94
4.14
4.27
4.21
4.45
4.51
4.51
4.51
4.99
4.99
4.99
4.99
5.25
5.38
5.25
5.25
5.38
5.44
5.56
5.44
5.56
5.56
4.75
5.25
6.25
6.37
6.69
6.94
6.81
7.56
7.75
7.69
8.19
8.31
8.25
8.87
8.93
8.93
8.93
10.18
10.18
10.18
10.18
11.06
11.19
11.06
11.06
11.19
11.56
11.68
11.56
11.68
11.68
18
Note: Mounting Styles J/JP, in 1.50 - 6.00 inch

bores, has 6 equally spaced bolt holes in the
mounting flange. The bolt pattern is oriented
to allow clearance for assembling mounting
bolts when ports or switches are in positions
1 and/or 3. This bolt pattern orientation puts one
hole each at positions 2 and 3, which results in
bolt interference with ports or switches specified
there. Consequently, ports or switches are not
available in position 2 or 4 on the head end of
mounting Styles J/JP.
Installations that require a switch and port(s)
located 90 degrees apart, on the head end of
mounting Styles J/JP, can be accommodated by
welding the flange with the mounting bolt pattern
rotated slightly or with a special bolt size and
quantity. Contact the factory in these cases.

Round Cap Flange Mounting
Style H

Series RDH
FD 2.5
ZF + STROKE
P + STROKE
EE
F
FC
E
HD
MM
UC
W
LH + STROKE
XF + STROKE
FB EQUALLY SPACED ON FC
1.50"-6.00" BORE 6X FB
7.00"-8.00" BORE 8X FB

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
1
2
Rod No.
1 (std)
2
All
All
All
All
All
All
All
All
1.88
1.88
2.38
3.00
3.88
4.61
5.75
7.00
8.00
9.25
EE
NPTF1
3/8
3/8
1/2
1/2
3/4
3/4
3/4
1
1 1/4
1 1/4
F
SAE2
6
6
8
8
12
12
12
16
20
20
0.38
0.38
0.44
0.50
0.63
0.75
0.88
1.00
1.00
1.13
FB
FC
FD
0.28
0.28
0.34
0.41
0.53
0.66
0.78
0.91
0.91
1.06
2.75
2.75
3.31
4.13
5.25
6.25
7.50
9.13
10.13
11.63
30
30
30
30
30
30
30
30
22.5
22.5
HD
1.60
1.60
2.04
2.37
2.81
3.20
3.79
4.58
5.11
5.76
UC
3.38
3.38
4.00
5.00
6.38
7.63
9.00
10.94
11.94
13.75
Add Stroke
LH
3.44
3.81
4.69
5.13
5.88
6.37
6.99
8.25
8.88
9.37
P
1.19
1.19
1.93
1.88
2.06
2.50
2.56
3.00
3.25
3.25


Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod No.
MM Rod
Add Stroke
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.07
3.25
3.19
3.39
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
XF
4.00
4.50
5.38
5.50
5.81
6.06
5.94
6.69
6.88
6.81
7.31
7.44
7.37
7.99
8.05
8.05
8.05
9.31
9.31
9.31
9.31
9.94
10.06
9.94
9.94
10.06
10.43
10.56
10.43
10.56
10.56
ZF
4.37
4.88
5.81
5.94
6.31
6.56
6.44
7.31
7.50
7.44
8.06
8.19
8.12
8.87
8.93
8.93
8.93
10.31
10.31
10.31
10.31
10.94
11.06
10.94
10.94
11.06
11.56
11.68
11.56
11.68
11.68
19
Note: Mounting Style H, in 1.50 - 6.00 inch bores,

has 6 equally spaced bolt holes in the mounting
flange. The bolt pattern is oriented to allow clearance for assembling mounting bolts when ports or
switches are in positions 1 and/or 3. This bolt
pattern orientation puts one hole each at positions
2 and 3, which results in bolt interference with
ports or switches specified there. Consequently,
ports or switches are not available in position 2 or
4 on the cap end of mounting Style H.
Installations that require a switch and port(s)
located 90 degrees apart, on the cap end of
mounting Style H, can be accommodated by
welding the flange with the mounting bolt pattern
rotated slightly or with a special bolt size and
quantity. Contact the factory in these cases.

Series RDH
Double Rod Models 1.50" to 8.00" Bore

Double Rod Cylinder
Styles KT & KDD
ZM + 2 X STROKE
LD + STROKE
PK + STROKE
EE
W
Y
MM
MM
Rod End #1
Rod End #2
Styles KJ / KJP
WF
WT
W
WF
WT
W
YF
ZN + 2 X STROKE
ZN + 2 X STROKE
PK + STROKE
PK + STROKE
EE
EE
YF
MM
MM
MM
MM
Rod End #1
Rod End #2

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
EE
LJ + STROKE
LJ + STROKE
PK
0.56
0.69
0.69
0.81
0.69
0.94
0.81
0.81
1.00
0.94
0.94
1.06
1.00
1.00
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.06
1.19
1.06
1.06
1.19
1.06
1.19
1.06
1.19
1.19
Add
Stroke
1.22
1.22
1.76
1.76
1.90
1.90
1.90
2.02
2.02
2.02
2.35
2.35
2.35
2.50
2.50
2.50
2.50
2.79
2.79
2.79
2.79
3.16
3.16
3.16
3.16
3.16
3.21
3.21
3.21
3.21
3.21
Styles KJ / KJP
WF
NPTF
SAE
3/8
3/8
1/2
1/2
1/2
1/2
1/2
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
3/4
1
1
1
1
1 1/4
1 1/4
1 1/4
1 1/4
1 1/4
1 1/4
1 1/4
1 1/4
1 1/4
1 1/4
6
6
8
8
8
8
8
12
12
12
12
12
12
12
12
12
12
16
16
16
16
20
20
20
20
20
20
20
20
20
20
WT
1.19
1.69
1.38
1.50
1.44
1.69
1.56
1.69
1.88
1.81
1.94
2.06
2.00
2.19
2.25
2.25
2.25
2.44
2.44
2.44
2.44
2.44
2.56
2.44
2.44
2.56
2.69
2.81
2.69
2.81
2.81
0.81
1.31
0.94
1.06
0.94
1.19
1.06
1.06
1.25
1.19
1.19
1.31
1.25
1.31
1.37
1.37
1.37
1.44
1.44
1.44
1.44
1.44
1.56
1.44
1.44
1.56
1.56
1.69
1.56
1.69
1.69
All Other Mounts
YF
LJ
ZN
2.87
3.37
3.26
3.38
3.44
3.69
3.56
3.82
4.00
3.94
4.14
4.27
4.21
4.45
4.51
4.51
4.51
4.99
4.99
4.99
4.99
5.25
5.38
5.25
5.25
5.38
5.44
5.56
5.44
5.56
5.56
Add
Stroke
4.78
4.78
6.09
6.09
6.78
6.78
6.78
7.59
7.59
7.59
8.10
8.10
8.10
8.70
8.70
8.70
8.70
10.02
10.02
10.02
10.02
10.97
10.97
10.97
10.97
10.97
11.46
11.46
11.46
11.46
11.46
Add 2X
Stroke
6.10
7.10
7.53
7.78
8.03
8.53
8.28
8.90
9.28
9.16
9.91
10.15
10.03
10.66
10.78
10.78
10.78
12.03
12.03
12.03
12.03
12.67
12.92
12.67
12.67
12.92
13.09
13.34
13.09
13.34
13.34
LD
ZM
2.12
2.62
2.51
2.63
2.69
2.94
2.81
3.07
3.25
3.19
3.39
3.52
3.46
3.70
3.76
3.76
3.76
4.24
4.24
4.24
4.24
4.25
4.38
4.25
4.25
4.38
4.44
4.56
4.44
4.56
4.56
Add
Stroke
4.34
5.09
5.40
5.40
5.90
5.90
5.90
6.53
6.53
6.53
7.27
7.27
7.27
7.90
7.90
7.90
7.90
9.15
9.15
9.15
9.15
9.54
9.54
9.54
9.54
9.54
9.96
9.96
9.96
9.96
9.96
Add 2X
Stroke
5.48
6.48
6.78
7.03
7.28
7.78
7.53
8.15
8.53
8.41
9.16
9.40
9.28
9.91
10.03
10.03
10.03
11.28
11.28
11.28
11.28
11.67
11.92
11.67
11.67
11.92
12.09
12.34
12.09
12.34
12.34
How to Use Double Rod Cylinder Drawing Dimensions

To determine the dimensions for a double rod cylinder, first
refer to the desired mounting style of the single rod version,
as seen in the preceding pages of this catalog. When you
have the required dimensions from that drawing, return to
this page to supplement and replace the single rod
dimensions with those shown on the double rod drawing
and table above. Note that double rod cylinders have a
head at both ends and that dimension LD replaces LB, and
LJ replaces LG. The double rod dimensions differ from, or
are in addition to those for single rod cylinders shown on
preceding pages and provide the information needed to

completely dimension a double rod cylinder.
On a double rod cylinder where the two rod ends are
different, be sure to clearly state which rod end is to be
assembled at which end. Port position 1 is standard. If
other than standard, specify position 2, 3 or 4 when
viewed from rod end #1 only. See Port information page
for more details.
20


Series RDH
Cylinder Mounting Accessories
Accessory Load Capacity
Rod End Accessories
The various accessories on this and the following pages

have been load rated for your convenience. The load
capacity, shown in the table below, is the recommended
maximum load for that accessory based on a 4:1 design
factor in tension. (Pivot Pin is rated in shear.) Before
specifying, compare the actual load or the tension (pull)
force at maximum operating pressure of the cylinder with
the load capacity of the accessory you plan to use. If load
or pull force of cylinder exceeds load capacity of accessory,
consult factory.
Accessories offered for the rod end of the cylinder include:

Rod Clevis, Eye Bracket, Knuckle, Clevis Bracket and
Pivot Pin. To select the proper part number for any desired
rod mounted accessory, refer to the table below and look
opposite the thread size of the rod end as indicated in
the first column. The Pivot Pins, Eye Brackets and Clevis
Brackets are listed opposite the pin diameter that fits their
mating Knuckles or Clevises.
Thread
Size
Pin
5/16-24
7/16-20
1/2-20
3/4-16
3/4-16
7/8-14
1-14
1-14
1 1/4-12
1 1/4-12
1 1/2-12
1 3/4-12
1 7/8-12
2 1/4-12
2 1/2-12
2 3/4-12
3 1/4-12
3 1/2-12
4-12
0.312
0.500
0.500
0.750
0.750
1.000
1.000
1.000
1.375
1.375
1.750
2.000
2.000
2.500
3.000
3.000
3.500
4.000
4.000
Includes pivot pin.
Rod Clevis
Part
Load
Number
Capacity
(lb)
2600
4250
4900
11200
11200
18800
19500
19500
33500
33500
45600
65600
65600
98200
98200
98200
156700
193200
221200
05122100001
0509400000
0509410000
0509420000
1332840000
0509430000
0509440000
1332850000
0509450000
1332860000
0509460000
0509470000
0509480000
0509490000
0509500000
0509510000
0509520000
0509530000
0509540000
2
Mounting Plate or Eye Bracket

Forged Steel or Cast Ductile Iron
Part
Load Capacity
Number
(lb)
0959810031
1850
4620
09598100502
4620
09598100502
12370
09598100752
12370
09598100752
20450
09598101002
20450
09598101002
20450
09598101002
0959810138
33500
0959810138
33500
0959810175
49480
70100
09598102002
70100
09598102002
98200
09598102502
121940
09598103002
121940
09598103002
0959810350
187910
0959810400
268000
0959810400
268000
0683680000
0683680000
0683690000
0683690000
0683700000
0683700000
0683700000
0683710000
0683710000
0683720000
0683730000
0683730000
0683740000
0683750000
0683750000
0735450000
0735470000
0735470000
8600
8600
19300
19300
34300
34300
34300
65000
65000
105200
137400
137400
214700
309200
309200
420900
565800
565800
Cylinder accessory dimensions conform to ANSI/NFPA/T3.6.8 R3-2010
Forged Steel or Cast Ductile

Iron Mounting Plate or
Eye Bracket Dimensions3
Approx.
20
CB
CD .001
DD
(4X)
LR
FL
Note: Cast ductile iron eye

brackets must not be welded
in place.
R
E
R
E
Cast or Forged
Part Number5
0959810031
0959810050
095981B075
0959810075
0959810100
0959810138
0959810175
0959810200
0959810250
0959810300
0959810350
0959810400
Pivot Pin
Part
Shear
Number
Capacity
(lb)
Pin
0.312
0.500
0.750
0.750
1.000
1.375
1.750
2.000
2.500
3.000
3.500
4.000
CB
0.31
0.75
1.06
1.25
1.50
2.00
2.50
2.50
3.00
3.00
4.00
4.50
CD
0.314
0.503
0.750
0.753
1.003
1.378
1.753
2.003
2.503
3.003
3.503
4.003
DD
0.27
0.41
0.53
0.53
0.66
0.66
0.91
1.06
1.19
1.31
1.81
2.06
E
(As Cast)
2.25
2.50
3.50
3.50
4.50
5.00
6.50
7.50
8.50
9.50
12.63
14.88
FL
LR
0.38
0.38
0.63
0.63
0.88
1.004
1.254
1.50
1.75
2.00
2.506
3.006
1.00
1.13
1.88
1.88
2.38
3.00
3.38
4.00
4.75
5.25
6.506
7.506
0.59
0.69
1.06
1.13
1.37
1.88
2.13
2.38
2.88
3.13
3.88
4.38
M
(As Cast)
0.38
0.50
0.75
0.75
1.00
1.38
1.75
2.00
2.50
3.00
3.50
4.06
R
1.75
1.63
2.55
2.55
3.25
3.82
4.95
5.73
6.58
7.50
9.62
11.45
For Use With BB

Mount Per Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
When used to mate with the Rod Clevis, select by pin diameter in the table above.
These dimensions vary from NFPA standard. F is increased by 0.13. Sufficient LR clearance remains for full swing arc with Parker cap clevis
cylinders and rod clevises.
5
Eye Brackets with pin diameters 0.500 thru 1.000 are forged steel. Eye Brackets with 0.312 and 1.375 pin diameter and larger are cast
ductile iron.
6
Mounting base thickness dimension F is increased on these sizes to provide greater load capacity than the former fabricated steel design.
Cast ductile iron dimensions F and FL are 0.81 larger for 3.500 pin diameter and 1.06 larger for 4.000 pin diameter.
3
4
21


Series RDH

Rod Clevis Dimensions
ER
CW
CB
CW
CD .001
CE
A
KK Thread
Part Number
05122100002
0509400000
0509410000
0509420000
1332840000
0509430000
0509440000
1332850000
0509450000
1332860000
0509460000
0509470000
0509480000
0509490000
0509500000
0509510000
0509520000
0509530000
0509540000
Pin
0.312
0.500
0.500
0.750
0.750
1.000
1.000
1.000
1.375
1.375
1.750
2.000
2.000
2.500
3.000
3.000
3.500
4.000
4.000
CB
0.81
0.75
0.75
1.13
1.13
1.63
1.63
1.63
1.88
2.00
2.25
3.00
3.00
3.50
3.50
3.50
3.503
4.003
4.003
0.34
0.77
0.77
1.27
1.27
1.52
1.52
1.52
2.04
2.04
2.54
2.54
2.54
3.04
3.04
3.04
4.04
4.54
4.54
CD
0.314
0.503
0.503
0.753
0.753
1.003
1.003
1.003
1.378
1.378
1.753
2.003
2.003
2.503
3.003
3.003
3.503
4.003
4.003
CE
CW
ER
2.25
1.50
1.50
2.13
2.38
2.94
2.94
3.13
3.75
4.13
4.50
5.50
5.50
6.50
6.75
6.75
7.75
8.81
8.81
0.20
0.49
0.49
0.62
0.62
0.74
0.74
0.74
0.99
0.99
1.24
1.24
1.24
1.49
1.49
1.49
1.98
2.23
2.23
0.30
0.50
0.50
0.75
0.75
1.00
1.00
1.00
1.38
1.38
1.75
2.00
2.00
2.50
2.75
2.75
3.50
4.00
4.00
KK
Thread
5/16-24
7/16-20
1/2-20
3/4-16
3/4-16
7/8-14
1-14
1-14
1 1/4-12
1 1/4-12
1 1/2-12
1 3/4-12
1 7/8-12
2 1/4-12
2 1/2-12
2 3/4-12
3 1/4-12
3 1/2-12
4-12
Rod Clevises with pin diameters .312 thru 1.375 are forged steel. Rod Clevises with 1.750 pin diameters and larger
are cast ductile iron.
2
Includes Pivot Pin
3
Consult appropriate cylinder rod end dimensions for compatibility.
1
Pivot Pin Dimensions

CL
+.001
CD -.002
Part Number
0683680000
0683690000
0683700000
0683710000
0683720000
0683730000
0683740000
0683750000
0735450000
07354700004
4
CD
0.500
0.750
1.000
1.375
1.750
2.000
2.500
3.000
3.500
4.000
CL
1.88
2.63
3.13
4.19
5.19
5.19
6.19
6.25
8.25
9.00
Notes:
Pivot Pins are furnished with Clevis Mounted Cylinders as
standard.
Pivot Pins are furnished with (2) Retainer Rings.
Pivot Pins must be ordered as a separate item if to be used with
Knuckles, Rod Clevises, or Clevis Brackets.
This size supplied with cotter pins.
22


Series RDH

Rod End Accessories
Accessory Load Capacity
Accessories offered for the rod end of the cylinder

include Rod Clevis, Eye Bracket, Knuckle, Clevis Bracket,
and Pivot Pin. To select the proper part number for any
rod mounted accessory, refer to the table below and
look in the row to the right of the rod thread in the first
column. The Pivot Pins, Eye Brackets and Clevis Brackets
are listed opposite the pin diameter that fits their mating
Knuckles or Clevises.
Thread
Size
Pin
5/16-24
7/16-20
1/2-20
3/4-16
7/8-14
1-14
1 1/4-12
1 1/2-12
1 3/4-12
1 7/8-12
2 1/4-12
2 1/2-12
2 3/4-12
3 1/4-12
3 1/2-12
4-12
N/A
0.438
0.500
0.500
0.750
1.000
1.000
1.375
1.750
2.000
2.000
2.500
3.000
3.000
3.500
3.500
4.000
4.000
Knuckle
Part
Load
Number
Capacity
(lb)
0740750000
0690890000
0690900000
0690910000
0690920000
0690930000
0690940000
0690950000
0690960000
0962160000
0962170000
0962180000
0962190000
0962200000
0962210000
0962220000
N/A
3300
5000
5700
12100
13000
21700
33500
45000
53500
75000
98700
110000
123300
161300
217300
273800
N/A
The various accessories have been load rated for your

convenience. The load capacity, shown in the table below,
is the recommended maximum load for that accessory
based on a 4:1 design factor in tension. (Pivot Pin is rated
in shear.) Before specifying, compare the actual load or
the tension (pull) force at the maximum operating pressure
of the cylinder with the load capacity of the accessory you
plan to use. If load or pull force of cylinder exceeds load
capacity of accessory, consult factory.
Clevis Bracket
Forged Steel or
Fabricated Steel
Cast Ductile Iron
Part
Load
Part
Load
Number
Capacity (lb)
Number
Capacity (lb)
0960160044
0960160050
0960160050
0960160075
0960160100
0960160100
0960160138
0960160175
0960160200
0960160200
0960160250
0960160300
N/A
0960160350
0960160350
0960160400
N/A
2830
7740
7740
13600
23000
23000
39500
49480
72400
72400
98700
123300
N/A
200400
200400
292100
N/A
0740760000
0692050000
0692050000
0692060000
0692070000
0692070000
0692080000
0692090000
0692100000
0692100000
0692110000
0692120000
0692130000
0735420000
0735420000
0735430000
N/A
3600
7300
7300
10880
15180
15180
23560
21520
26000
26000
28710
28190
31390
80250
80250
98420
N/A
Pivot Pin
Part
Shear
Number
Capacity
(lb)
0740780000
0683680000
0683680000
0683690000
0683700000
0683700000
0683710000
0683720000
0692150000
0692150000
0683740000
0683750000
0692160000
0735450000
0735450000
0821810000
07354700001
6600
8600
8600
19300
34300
34300
65000
105200
137400
137400
214700
309200
309200
420900
420900
565800
565800
Forged Steel or Cast Ductile Iron Clevis Bracket Dimensions

Approx.
20
CW
CB
+.004
CD +.002
DD
(X4)
LR
FL
CW
Note: Cast ductile iron

clevis brackets must not be
welded in place.
F
R
E
R
E
Cast or Forged
Part Number2
Pin
CB
CD
CW
DD
0960160044
0960160050
0960160075
0960160100
0960160138
0960160175
0960160200
0960160250
0960160300
0960160350
0960160400
0.438
0.500
0.750
1.000
1.375
1.750
2.000
2.500
3.000
3.500
4.000
0.46
0.78
1.28
1.53
2.03
2.53
2.53
3.03
3.03
4.03
4.53
0.440
0.503
0.753
1.003
1.378
1.753
2.003
2.503
3.003
3.503
4.003
0.37
0.50
0.63
0.75
1.00
1.25
1.25
1.50
1.50
2.00
2.25
0.27
0.41
0.53
0.66
0.66
0.91
1.06
1.19
1.31
1.81
2.06
E
(As
Cast)
2.25
2.50
3.50
4.50
5.00
6.50
7.50
8.50
9.50
12.63
14.88
FL
LR
0.38
0.38
0.63
0.75
0.88
0.94
1.38
1.50
1.88
2.31
2.88
1.00
1.13
1.88
2.25
3.00
3.13
3.75
4.50
5.38
6.38
7.50
0.56
0.63
1.06
1.25
1.94
2.00
2.25
2.81
3.31
3.88
4.50
M
(As
Cast)
0.44
0.56
0.75
1.00
1.38
1.75
2.00
2.50
3.00
3.50
4.00
R
1.75
1.63
2.56
3.25
3.81
4.94
5.75
6.59
7.50
9.62
11.50
For Use With

B Mount
Per Bore
1.50
2.00, 2.50
3.25
4.00
5.00
6.00
7.00
8.00
Clevis Brackets with pin diameters .438 thru 1.000 are forged steel. Clevis Brackets with 1.375 pin and larger are cast ductile iron.
23


Series RDH

Knuckle Dimensions
CD
Pivot Pin Dimensions
CB
ER Max.
ER Max.
CL
CD
CD .001
CA
CD .001
KK Thread CA
LR Min.
2 X CD
0740750000
0690890000
0690900000
0690910000
0690920000
0690930000
0690940000
0690950000
0690960000
0962160000
0962170000
0962180000
0962190000
0962200000
0962210000
0962220000
+.001
CD -.002
KK Thread
Pin
0.438
0.500
0.500
0.750
1.000
1.000
1.375
1.750
2.000
2.000
2.500
3.000
3.000
3.500
3.500
4.000
Part Number
JL
2 X CD
Thread Size thru 1 3/4-12

Part Number
CB
Thread Size 1 7/8-12 & Larger
CA
CB
0.75
0.75
0.75
1.13
1.13
1.63
2.00
2.25
2.25
3.00
3.50
3.50
3.63
4.50
5.00
5.50
1.50
1.50
1.50
2.06
2.38
2.81
3.44
4.00
4.38
5.00
5.81
6.13
6.50
7.63
7.63
9.13
0.43
0.75
0.75
1.25
1.50
1.50
2.00
2.50
2.50
2.50
3.00
3.00
3.50
4.00
4.00
4.50
CD
0.440
0.503
0.503
0.753
1.003
1.003
1.378
1.753
2.003
2.003
2.503
3.003
3.003
3.503
3.503
4.003
ER
JL
0.53
0.59
0.59
0.87
1.15
1.15
1.55
1.96
2.24
2.24
2.76
3.30
3.30
3.87
3.87
4.43
3.00
3.50
4.00
4.00
6.00
6.00
6.00
LR
min
2.77
3.09
3.58
3.58
4.18
4.18
4.80
0740780000
0683680000
0683690000
0683700000
0683710000
0683720000
0692150000
0683740000
0683750000
0692160000
0735450000
0821810000
07354700001
KK
Thread
5/16-24
7/16-20
1/2-20
3/4-16
7/8-14
1-14
1 1/4-12
1 1/2-12
1 3/4-12
1 7/8-12
2 1/4-12
2 1/2-12
2 3/4-12
3 1/4-12
3 1/2-12
4-12
MR
25
CB
1.31
1.88
2.63
3.13
4.19
5.19
5.69
6.19
6.25
6.75
8.25
8.69
9.00
Pivot Pins are furnished with Clevis

Mounted Cylinders as standard.
Pivot Pins are furnished with (2)
Retainer Rings.
Pivot Pins must be ordered as a
separate item if to be used with
Knuckles, Rod Clevises, or
Clevis Brackets.
CW
+.004
CD +.002
DD
(X4)
LR
FL
CW
CL
Notes:
Fabricated Steel Clevis Bracket Dimensions

M
CD
0.438
0.500
0.750
1.000
1.375
1.750
2.000
2.500
3.000
3.000
3.500
4.000
4.000
F
R
E
R
E
Fabricated Steel
Part Number
Pin
CB
CD
CW
DD
FL
LR
MR
0740760000
0692050000
0692060000
0692070000
0692080000
0692090000
0692100000
0692110000
0692120000
0692130000
0735420000
0735430000
0.438
0.500
0.750
1.000
1.375
1.750
2.000
2.500
3.000
3.000
3.500
4.000
0.46
0.80
1.30
1.59
2.09
2.59
2.59
3.09
3.09
3.59
4.09
4.59
0.440
0.503
0.753
1.003
1.378
1.753
2.003
2.503
3.003
3.003
3.503
4.003
0.38
0.50
0.63
0.75
1.00
1.25
1.50
1.50
1.50
1.50
2.00
2.00
0.27
0.41
0.53
0.66
0.66
0.91
1.06
1.19
1.31
1.31
1.81
2.06
2.25
3.50
5.00
6.50
7.50
9.50
12.75
12.75
12.75
12.75
15.50
17.50
0.38
0.50
0.63
0.75
0.88
0.88
1.00
1.00
1.00
1.00
1.69
1.94
1.00
1.50
1.88
2.25
3.00
3.63
4.25
4.50
6.00
6.00
6.69
7.69
0.63
0.75
1.19
1.50
2.00
2.75
3.19
3.50
4.25
4.25
5.00
5.75
0.38
0.50
0.75
1.00
1.38
1.75
2.25
2.50
3.00
3.00
3.50
4.00
0.50
0.63
0.91
1.25
1.66
2.22
2.78
3.13
3.59
3.59
4.13
4.88
24
For Use With

B Mount
Per Bore
1.75
2.55
1.50
3.82
2.00, 2.50
4.95
3.25
5.73
4.00
7.50
5.00
9.40
6.00
9.40
7.00
9.40
8.00
9.40
12.00
13.75


Series RDH
Spherical Bearing Mounting Accessories

Accessories for spherical bearing mount cylinders
include Spherical Rod Eyes, Pivot Pins and Clevis
Spherical Rod Eye

(Inch Sizes)
CD
Note: Standard spherical bearing is maintenance-free (sealed) for CD > 0.5000"
EX
ER (Max)
0.5000 0.86 0.80 0.44
7/16-20
0.88 0.78
2644
0961000075 1.02
0.7500
1.25 1.14 0.66
3/4-16
1.31 1.06
9441
3.25
0961000100
1.52
1.0000
1.88 1.34 0.88
1-14
1.50 1.45
16860
4.00
0961000138 2.02
1.3750
2.13 1.67 1.19
1 1/4-12
2.00 1.91
28562
5.00
0961000175
1.7500
2.50 2.05 1.53
1 1/2-12
2.00 2.16
43005
6.00
0961000200 2.89 2.0000
2.75 2.60 1.75
1 7/8-12
2.75 2.50
70193
2.50
A
JK Thd
JL
Order to fit Piston Rod Thread Size
Load
Capacity (lb)
0961000050 0.72
1.50
2.00
CE
Pivot Pin (Inch Sizes)
CD
+.0000
-.0005
2.14
Bore Part Number
CL
CD
CL
Shear
Capacity (lb)
0839620000
.4997 -.0004
1.56
8600
0839630000
.7497 -.0005
2.03
19300
3.25
0839640000
.9997 -.0005
2.50
34300
4.00
0839650000
1.3746 -.0006
3.31
65000
5.00
0839660000
1.7496 -.0006
4.22
105200
6.00
0839670000
1.9996 -.0007
4.94
137400
1.50
2.00
CD
2.50
Pivot Pins are furnished with (2) Retainer Rings.
ER
LE
JK
Thread
Size
CE
JL
EX
Bore Part Number
Lube
Fitting
LE
Brackets. To identify the proper part number for the

desired accessory, see the tables below.
Clevis Bracket for SB Mount Cap or Spherical Rod Eye (Inch Sizes)
Cast Ductile Iron
CW
Fabricated Steel
CF
CW
CW
CF
CW
MR
CD .001
FL
CD .001
DD
(4X)
LR
FL
R
E
R
E
R
E
Bore
Pin
1.50
0.500
0959450000
0839470000
0.750
0959300000
0839480000
2.50
DD
(4 X)
2.00
LR
Cast Ductile Iron Fabricated Steel

Part Number
Part Number
CD
CF
R
E
CW
DD
FL
LR
MR
Load
Capacity (lb)
0.503 0.45
0.50
0.41
3.00
0.50
1.50
0.94
0.50
0.63
2.05
5770
0.753 0.67
0.63
0.53
3.75
0.63
2.00
1.38
0.88
1.00
2.76
9450
3.25
1.000
0959310000
0839490000
1.003 0.89
0.75
0.53
5.50
0.75
2.50
1.69
1.00
1.19
4.10
14300
4.00
1.375
0959320000
0839500000
1.378 1.20
1.00
0.66
6.50
0.88
3.50
2.44
1.38
1.63
4.95
20322
5.00
1.750
0959330000
0839510000
1.753 1.55
1.25
0.91
8.50
1.25
4.50
2.88
1.75
2.06
6.58
37800
6.00
2.000
0959340000
0839520000
2.003 1.77
1.50
0.91 10.63 1.50
5.00
3.00
2.00
2.38
7.92
50375
25


Series RDH
Spherical Bearing Mounting Accessories

Accessories for spherical bearing mount cylinders
include Spherical Rod Eyes, Pivot Pins and Clevis
Spherical Rod Eye

(Metric Sizes)
Brackets. To identify the proper part number for the

desired accessory, see the tables below.
EN
EU
EF
3
3
CN
LF
Note: Standard spherical bearing is maintenance-free (sealed)
CH
AX
A
KK
P
MA Torque
Bore
(inches)
Part
Number
A
max
AX
min
CH
CN
EF
max
EN
EU
KK
LF
min
MA
max
Nm
N
max
Load
Cap. (lb)
5301
1.50
1452560000
55
19
58
20 -0.012 27.5 16 -.012
13
M14x1.5
25
25
25
M8
2.00
1452570000
62
23
68
25 -0.012 32.5 20 -.012
17
M16x1.5
30
25
30
M8
9425
2.50
1452580000
80
29
85
30 -0.012
40
22 -.012
19
M20x1.5
35
45
36
M10
14726
50
3.25
1452590000
90
37
105
40 -0.012
28 -.012
23
M27x2
45
45
45
M10
24887
4.00
1452600000
105
46
130
50 -0.012 62.5 35 -.012
30
M33x2
58
80
55
M12
37699
5.00
1452610000
134
57
150
60 -0.015
44 -.015
38
M42x2
68
160
68
M16
58905
6.00
1452620000
156
64
185
80 -0.015 102.5 55 -.015
47
M48x2
92
310
90
M20
84823
7.00, 8.00 1452630000
190
86
240
100 -0.020
57
M64x3
116
530
110
M24
150796
80
120
70 -.020
Clevis Bracket and Pin for Style SBM Cap or Spherical Rod Eye (Metric Sizes)
CP
CG
LO
GL
FO
SR
CF
LG LJ
HB
FM
CO
KC
RE
TA
UK
UJ
Bore
(inches)
Part
Number
CF
CG CO
+0.1, N9
K7/h6 +0.3
CP
FM FO GL
js11 js14 js13
HB KC 0,
+0.30
LG
LJ
LO
RE SR TA
js13 max js13
UJ
UK
Load
Cap.
(lb)
4496
1.50
1455320000
20
16
16
50
55
20
64
14
4.3
39
40
80
85
20
58
120
90
2.00
1455330000
25
20
25
60
65
22
78
16
5.4
48
49
98
100
25
70
140
110
7194
2.50
1455340000
30
22
25
70
85
24
97
18
5.4
62
63
120
115
30
90
160
135
11240
3.25
1455350000
40
28
36
80
100
24
123
22
8.4
72
73
148
135
40
120
190
170 17985
4.00
1455360000
50
35
36
100
125
35
155
30
8.4
90
92
190
170
50
145
240
215 28101
5.00
1455370000
60
44
50
120
150
35
187
39
11.4
108
110
225
200
60
185
270
260 44962
6.00
1455380000
80
55
50
160
190
35
255
45
11.4
140
142
295
240
80
260
320
340 71939
7.00, 8.00 1455390000
100
70
63
200
210
35
285
48
12.4
150
152
335 300
100
300 400 400 112404
All dimensions are in millimeters unless otherwise specified.
26


Series RDH
Linear Alignment Couplers
Linear Alignment Couplers are available in 19 standard thread sizes

Cost Saving Features and Benefits Include:
n
Maximize reliability for trouble-free

operation, long life and lower operating
costs
Simplify cylinder installation and

reduce assembly costs
Lower maintenance costs from possible

machine misalignment
Increase cylinder life by reducing wear on

piston and rod bearings
Alignment Coupler
See Table for Part Numbers and Dimensions

A THREAD
H
ACROSS FLATS
G
ACROSS FLATS
1/8 TOTAL
MOVEMENT
1/16
CENTERLINE
M TOTAL
MOVEMENT
A THREAD
E DEEP
Part Numbers and Dimensions
Part Number
A1
Thread
Size
1347570031
1347570038
1347570044
1347570050
1347570063
1347570075
1347570088
1347570100
1347570125
1337390125
1337390150
1337390175
1337390188
1337390200
1337390225
1337390250
1337390275
1337390300
1337390325
1337390425
5/16-24
3/8-24
7/16-20
1/2-20
5/8-18
3/4-16
7/8-14
1-14
1 1/4-12
1 1/4-12
1 1/2-12
1 3/4-12
1 7/8-12
2-12
2 1/4-12
2 1/2-12
2 3/4-12
3-12
3 1/4-12
4 1/4-12
1.13
1.75
1.13
1.75
1.38
2.00
1.38
2.00
1.38
2.00
2.00
2.31
2.00
2.31
3.13
3.00
3.13
3.00
3.50
4.00
4.00
4.38
4.00
4.38
5.00
5.63
5.00
5.63
6.75
6.38
7.00
6.50
7.00
6.50
6.50
7.00
9.25
8.50
12.88 11.25
0.94
0.94
1.13
1.13
1.13
1.63
1.63
2.38
2.38
2.00
2.25
2.25
3.00
3.00
3.25
4.00
4.00
4.00
5.25
7.75
0.50
0.50
0.75
0.75
0.75
1.13
1.13
1.63
1.63
2.00
2.25
2.25
3.00
3.00
3.50
3.50
3.50
3.50
4.50
4.50
0.50
0.50
0.63
0.63
0.63
0.94
0.94
1.44
1.44
1.50
1.75
1.75
2.25
2.25
2.75
3.25
3.25
3.25
4.00
5.50
0.38
0.38
0.50
0.50
0.50
0.75
0.75
1.25
1.25
1.25
1.50
1.50
1.94
1.94
2.38
2.88
2.88
2.88
3.38
4.88
0.75
0.75
0.88
0.88
0.88
1.31
1.31
1.88
1.88
1.69
1.94
1.94
2.63
2.63
2.88
3.38
3.38
3.38
4.50
7.00
0.38
0.38
0.38
0.38
0.38
0.44
0.44
0.75
0.75
0.75
0.88
0.88
1.38
1.38
1.63
1.63
1.63
1.63
2.00
1.50
0.94
0.94
1.09
1.09
1.09
1.28
1.28
1.78
1.78
2.50
2.75
2.75
3.38
3.38
3.75
3.88
3.88
3.88
5.50
8.75
6
6
6
6
6
6
6
6
6
10
10
10
10
10
10
10
10
10
10
10
Max. Pull Max. Approx.

Load (lbs.) Weight (lbs.)
1200
2425
3250
4450
6800
9050
14450
19425
30500
30500
45750
58350
67550
77450
99250
123750
150950
180850
218450
370850
.35
.35
.55
.55
.55
1.4
1.4
4.8
4.8
6.9
9.8
9.8
19.8
19.8
35.3
45.3
45.3
45.3
Metric thread size couplers are also available, consult factory.
How to Order Linear Alignment Couplers When ordering a cylinder with a threaded male rod end, specify
the coupler of equal thread size by part number as listed in the table. For example, Piston Rod KK or CC
dimension is 3/4"-16, specify coupler part number 1347570075.
27


Series RDH
Style 55 Piston Rod End Accessories
Parker Style 55 Piston Rod End

Split Couplers and Weld Plates
C
D
F BOLTS
E
A B
SPLIT COUPLER
STYLE 55 ROD END
WELD PLATE
WARNING: Piston rod separation from the machine member can result in severe personal injury or
even death to nearby personnel. The cylinder user must make sure the weld holding the weld plate to the
machine is of sufficient quality and size to hold the intended load. The cylinder user must also make sure the
bolts holding split coupler to the weld plate are of sufficient strength to hold the intended load and installed
in such a way that they will not become loose during the machines operation.
Part Numbers and Dimensions

Rod A B C D E F Bolt Size Bolt Split Weld

Circle Coupler Plate

Part Number Part Number
0.625
1.50
2.00
0.50
0.56
.250
4
#10-24 x .94 LG
1.125 1472340062 1481740062
1.000
2.00
2.50
0.50
0.88
.250
6
1/4-20 x 1.25 LG
1.500 1472340100 1481740100
1.375
2.50
3.00
0.63
1.00
.250
6
5/16-18 x 1.00 LG 2.000 1472340138 1481740138
1.750
3.00
4.00
0.63
1.25
.250
8
5/16-18 x 1.75 LG 2.375 1472340175 1481740175
2.000
3.50
4.00
0.75
1.63
.375
12
3/8-16 x 2.25 LG
2.687 1472340200 1481740200
2.500
4.00
4.50
0.75
1.88
.375
12
3/8-16 x 2.50 LG
3.187 1472340250 1481740250
3.000
5.00
5.50
1.00
2.38
.375
12
1/2-13 x 3.25 LG
4.000 1472340300 1481740300
3.500
5.88
7.00
1.00
2.63
.375
12
5/8-11 x 3.50 LG
4.687 1472340350 1481740350
4.000
6.38
7.00
1.00
2.63
.375
12
5/8-11 x 3.50 LG
5.187 1472340400 1481740400
4.500
6.88
8.00
1.00
3.13
.375
12
5/8-11 x 4.00 LG
5.687 1472340450 1481740450
5.000
7.38
8.00
1.00
3.13
.375
12
5/8-11 x 4.00 LG
6.187 1472340500 1481740500
5.500
8.25
9.00
1.25
3.88
.375
12
3/4-10 x 5.00 LG
6.875 1472340550 1481740550
Note: Bolts are not included with split coupler or weld plate
28


Series RDH
Parts Identification / Tools

4
16
10
16
13
Cylinder Service Tool

(Head Torquing)
15
Notes:
Factory assembled piston rod assemblies (which include seals for the specified piston type)
are recommended. Do not remove the piston from the rod.
17
19
19
10
20
11
Optional
Magnetic Piston
Cylinders rated for high temperatures (Seal Codes V, H and D) may include a set screw to
lock the head to the cylinder body. Remove and replace it when servicing the cylinder.
18
11
12
14
10
11
10
11
B
2
Optional Mixed
Media Piston
Optional Hi Load and

Low Friction Piston
(Bronze Filled PTFE Seal)
Optional Extreme High

Temperature and Low
Friction Head
Parts Identification
Torque Tool Specifications
Symbol
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Head
Rod wiper
Rod seal
Rod wear ring1
End seal (o-ring)
Backup ring for end seal
Piston rod (single rod type)
Piston
Piston seal energizer
Piston seal
Piston wear ring
Piston joint o-ring
Piston rod nut2
Cylinder body (welded to cap)
Cap (welded to cylinder body)
Port (welded to cylinder body)
Head (optional)3
Rod wiper energizer 3,4
Rod seal energizer 3
Magnetic rings5
Spanner
Hole
2 holes on
head face
Cylinder
Service Tool
Fits standard square drive
on torque wrench
Head Torque Units
0.171
RDHSVCTL15
0.203
RDHSVCTL20
70
95
0.203
RDHSVCTL25
100
136
0.266
RDHSVCTL32
150
203
0.266
RDHSVCTL40
175
237
0.266
RDHSVCTL50
225
305
0.266
RDHSVCTL60
285
386
0.391
RDHSVCTL70
400
542
0.516
RDHSVCTL80
485
658
USA
Metric
Lb-Ft
N-m
55
75
Not used for 0.625" rod diameter

Only for 1.50" to 5.00" bores. For 6.00" to 8.00" bores, pistons are
threaded and torqued to the piston rod, and set screws are used to
lock the piston to the rod.
3
Used for Piston code F or Seal code H
4
Used for Seal codes M and D
5
Used for Piston code 7
1
29


Series RDH
Piston and Rod Seal Kits

Piston Seal Kits
Seal
Class
Bore Diameter
Piston
Code
1.50
2.00
2.50
3.25
4.00
B, 7
PK151RDH01
PK201RDH01
PK251RDH01
PK321RDH01
PK401RDH01
K, F
PK151RDHK1
PK201RDHK1
PK251RDHK1
PK321RDHK1
PK401RDHK1
B, K, F, 7
PK151RDHW1 PK201RDHW1 PK251RDHW1 PK321RDHW1 PK401RDHW1

PK151RDH02
PK201RDH02
PK251RDH02
PK321RDH02
PK401RDH02
B, K, F, 7
PK151RDH03
PK201RDH03
PK251RDH03
PK321RDH03
PK401RDH03
B, 7
PK151RDH04
PK201RDH04
PK251RDH04
PK321RDH04
PK401RDH04
K, F
PK151RDHK5
PK201RDHK5
PK251RDHK5
PK321RDHK5
PK401RDHK5
B, K, F, 7
B, F, K
PK151RDH08
PK201RDH08
Seal
Class
Piston
Code
5.00
6.00
7.00
8.00
B, 7
PK501RDH01
PK601RDH01
PK701RDH01
PK801RDH01
K, F
PK501RDHK1
PK601RDHK1
PK701RDHK1
PK801RDHK1
PK151RDH05
PK201RDH05
PK251RDH05
PK321RDH05
PK251RDH08
PK321RDH08
PK501RDHW1 PK601RDHW1 PK701RDHW1 PK801RDHW1
B, K, F, 7 PK501RDH02
PK601RDH02
PK701RDH02
PK801RDH02
B, K, F, 7 PK501RDH03
PK601RDH03
PK701RDH03
PK801RDH03
PK501RDH04
PK601RDH04
PK701RDH04
PK801RDH04
PK501RDHK5
PK601RDHK5
PK701RDHK5
PK801RDHK5
B, 7
K, F
B, K, F, 7 PK501RDH05
B, F, K
PK401RDH08
Bore Diameter
2
4
PK401RDH05
PK601RDH05
PK701RDH05
PK801RDH05

PK501RDH08
PK601RDH08
PK701RDH08
PK801RDH08
Rod Seal Kits

Seal Class
Class 1
Piston Rod Diameter

0.625
1.000
1.375
1.750
2.000
2.500
RKRDH00061
RKRDH00101
RKRDH00131
RKRDH00171
RKRDH00201
RKRDH00251
Class 2
RKRDH00062
RKRDH00102
RKRDH00132
RKRDH00172
RKRDH00202
RKRDH00252
Class 3
RKRDH00063
RKRDH00103
RKRDH00133
RKRDH00173
RKRDH00203
RKRDH00253
Class 4
RKRDH00064
RKRDH00104
RKRDH00134
RKRDH00174
RKRDH00204
RKRDH00254
Class 5
RKRDH00065
RKRDH00105
RKRDH00135
RKRDH00175
RKRDH00205
RKRDH00255
Class 8
N/A
RKRDH00108
RKRDH00138
RKRDH00178
RKRDH00208
RKRDH00258
Class 1 (Low Friction)
N/A
RKRDHF0101
RKRDHF0131
RKRDHF0171
RKRDHF0201
RKRDHF0251
N/A
RKRDHF0105
RKRDHF0135
RKRDHF0175
RKRDHF0205
RKRDHF0255
Class 1 (Metallic Scrapper)
RKRDHM0061 RKRDHM0101 RKRDHM0131 RKRDHM0171 RKRDHM0201 RKRDHM0251
Seal Class
Class 1
Piston Rod Diameter

3.000
3.500
4.000
4.500
5.000
5.500
RKRDH00301
RKRDH00351
RKRDH00401
RKRDH00451
RKRDH00501
RKRDH00551
Class 2
RKRDH00302
RKRDH00352
RKRDH00402
RKRDH00452
RKRDH00502
RKRDH00552
Class 3
RKRDH00303
RKRDH00353
RKRDH00403
RKRDH00453
RKRDH00503
RKRDH00553
Class 4
RKRDH00304
RKRDH00354
RKRDH00404
RKRDH00454
RKRDH00504
RKRDH00554
Class 5
RKRDH00305
RKRDH00355
RKRDH00405
RKRDH00455
RKRDH00505
RKRDH00555
Class 8
RKRDH00308
RKRDH00358
RKRDH00408
RKRDH00458
RKRDH00508
RKRDH00558
RKRDHF0301
RKRDHF0351
RKRDHF0401
RKRDHF0451
RKRDHF0501
RKRDHF0551
RKRDHF0305
RKRDHF0355
RKRDHF0405
RKRDHF0455
RKRDHF0505
RKRDHF0555
30


Common Modifications
Water Submersible Option

Several surface treatment options are
available for protection against the operating
environments.
Optional Dual End Seals resist external
pressure. Required for depths greater
than 25 feet.
Optional PolyPak Inner and Outer Rod
Seals resist internal and external pressure.
Required for depths greater than 25 feet.
Standard 17-4 Heat-Treated, Chrome-Plated,

High Tensile Stainless Steel Piston Rod
Material resists corrosion.
Specifications:
Standard Options for Water

Submersible Cylinders:
Submersion Depth to 15,000 feet

Nominal Pressure 3,000 psi
Operating Temperature -10F to +165F
17-4 PH chrome plated stainless steel piston rod
Stainless steel nametag
Material
Chrome plated cylinder body ID
Surface Treatments for Corrosion Protection
Electroless nickel plated exterior (head, cap and
cylinder body)
Inorganic zinc primer (zinc primer only without bond
coating)
Inorganic zinc primer with epoxy undercoat and
polyurethane or acrylic epoxy topcoat
Epoxy undercoat and topcoat
Cylinder Seal Construction:

0 to 25 feet depth Standard rod seal and end seals
25 to 5,000 feet depth
Subsea rod seal package that includes a
PolyPak oil seal and an outward-facing PolyPak
wiper to seal against water intrusion.
Subsea end seal package with ID oil seal and
body-end o-ring to seal against water intrusion.
Over 5,000 feet depth consult factory for details
Custom Options available for

Special Order:
All stainless steel construction
31


How to Order Water Submersible Option

How to order:
1. Specify the complete cylinder model number.
2. Put an S in the model number to indicate a Special Modification.
3. Include the 3 digit Submersible Code (see below).
4. For custom options, provide a complete description or drawing of your requirements.
Submersible Code
When selecting the submersible option, an S must be placed in the Model Number. Select Submersible Code
values for the required Submersion Depth, Cylinder Body, and Corrosion Protection. See the example Model
Number below:
Feature
Submersion Depth
Cylinder Body
Corrosion Protection
Code
Specification
For
1
2
3
P
C
Conventional rod seal, rod wiper and end seal

Submersible rod seal, rod wiper and end seal
Other
Plain cylinder body ID
Inorganic zinc primer
Electroless nickel plated exterior

Inorganic zinc primer, epoxy undercoat, and
polyurethane or acrylic epoxy topcoat.
Epoxy base and top coat.
Other
4
6
9
Depths to 25 feet
Depths to 5,000 feet
Specify depth / requirements
Splash and short term immersion service

where equipment is top coated by the
customer
Splash and short term immersion service
Long term immersion service
Specify requirements
Example:
4.00BBRDHKTS14A24.000
S = Submersible Code 2P1
(describes a 4" bore x 24" stroke Series RDH cylinder for submersion up to 5,000 feet, with a plain cylinder body ID and
inorganic zinc primer corrosion protection.)
Water Submersible Codes and Features Supplied

Depths to 5,000 feet1
Submersible Cylinder
Feature
17-4 PH stainless steel piston rod
Stainless steel nametag
Submersible rod seal and wiper
Dual end seals
Electroless nickel plated exterior
Inorganic zinc primer
Inorganic zinc primer with topcoats
Epoxy base and topcoat
2P1
X
X
X
X
2P3
X
X
X
X
2P4
X
X
X
X
Water Submersible Code1

2P6
2C1
X
X
X
X
X
X
X
X
X
X
X
2C3
X
X
X
X
X
X
2C4
X
X
X
X
X
2C6
X
X
X
X
X
X
X
X
X
Corresponding submersible codes for depths to 25 feet begin with 1 (e.g. 1P1, 1P3, etc.) and include all of the
features marked for 5,000 feet depth except Submersible Rod Seal, Rod Wiper and End Seals.
1
32


Hi Load Piston
The Exclusive Parker Hi Load Piston

The effective difference...
Parkers bronze filled PTFE ring design.
n Virtually eliminates leakage
n High load capacity
n High contamination tolerance
n Long life
n Low friction
Optional Hi Load Piston

Virtually zero leakage. The Hi Load piston assembly
provides virtually zero leakage with hydraulic and/or
water base fluids due to the continuous bronze filled
PTFE ring with a homogenous inner ring of Nitrile
rubber to apply seal preloading. The Nitrile energizer
provide enough initial radial force to eliminate low
pressure leakage. At higher pressure (above 2,000 psi)
the seal is also pressurized underneath, and is therefore
dynamically self-sealing.
The revolutionary Parker Hi Load piston assembly

was designed to increase and insure consistent quality
performance of the piston seals and your equipment.
Its a major innovative refinement over typical cast iron
piston rings and nitrile or fluorocarbon lipseals.
The Hi Load piston assembly overcomes the inherent
problems commonly associated with these conventional
types of seals, such as scoring of the cylinder bore due
to contamination, and it virtually eliminates leakage flow.
It can also reduce or eliminate the need for stop tubing.
It has much greater side load carrying capacity, and
most importantly, even at pressures up to 3,000 psi,
it has a longer wearing life than any seal that we have
tested to date.
The Hi Load piston assembly is comprised of a bronze
filled PTFE piston seal (with a nitrile energizer) and a
WearGard non-metallic wear ring to achieve dramatic
efficiency.
Reduced scoring. Low friction. The WearGard nonmetallic wear ring eliminates all metal-to-metal contact
between the piston and cylinder body. Some scoring
may occur even with the use of compatible materials
such as cast iron or bronze for the piston and steel
for the cylinder body. The combination of the high
imbeddability factor and the wiping action of the wear
ring prevents contamination from getting between the
piston bearing and sealing surfaces; therefore, scoring
is greatly reduced and cylinder life is extended. Other
benefits of the Hi Load piston are excellent lubricity and
minimum wear when using water base fluids, soluble oil
& water, or biodegradable fluids.
Extensive controlled contamination tests in our laboratory have shown the Hi Load piston to operate more
than 4 times longer than lip seals when high degrees
of contamination are present.
Note: Because the Hi Load piston prevents metal-tometal contact with the cylinder bore, steel pistons may
be used.
Higher side load carrying capacity. Under severe
side load conditions arising from long stroke or pivot
mounted cylinders, the characteristics of a non-metallic
wear ring provide increased side load carrying capa
bility, a distinctive benefit. The non-metallic bearing
can also absorb hydraulic shock and conform more to
the piston and cylinder body. The action of deformation
increases the area of contact, which in turn keeps the
contact stresses from increasing and permits the
Hi Load piston to have a higher side load carrying
capacity. This can often reduce or eliminate the need
for stop tubing.
The bronze filled PTFE resists extrusion in the clearance between the piston and bore much better than
Nitrile, and, as a result, increases the life of a cylinder,
significantly at higher pressures.
When ordering the Hi Load piston option for Series
RDH cylinders, specify K in the Piston field of the
model code.
ING
PISTON SEAL FRICTION

2 IN. BORE
Comparative Piston Seal Friction
IRO
NR
200
CA
ST
175
FRICTION LBS.
150
125
100
L
SEA
LIP
75
50
BR O
BACK
WITH
-UP
ED PTFE
NZE-FILL
25
500
1000
1500
2000
2500 3000
PRESSURE PSIG
33


Low Friction Seals
Low Friction Seal Option

n Smooth-running operation reduces stick/slip
or chatter
n Appropriate for servo applications

n Innovative seal geometry for maximum
sealing efficiency
n Bronze filled PTFE seals and WearGard wear

rings for low friction, rapid break-in and long
service life
Low Friction Rod Seal Design
n When ordering Series RDH cylinders, place an F

in the Piston field for Low Friction Seals.
A - Dual bronze filled PTFE step-seal rod
seals insure positive sealing and smooth
operation at low or high pressures.
B - Elastomer expander for pressure

compensation and low pressure
effectiveness.
C - Durable, energized bronze filled PTFE lip
wiper keeps contaminants out.
D - WearGard wear ring for high load
capacity, low friction and no metal-tometal contact.
Available for all standard piston rod

diameters larger than 0.625"
Low Friction Piston Seal Design

B
A - WearGard wear ring for high load

capacity, low friction and no metal-tometal contact.
B - Bronze filled PTFE piston seal ensures
maximum sealing efficiency.
C - Elastomer expander for pressure
compensation and low pressure
effectiveness.
Available for all standard bore diameters.
Seal Friction
Seal friction under a given set of working conditions is

not easily calculated due to the multiplicity of variables
involved. The following graph is offered as a guide
for use in performance calculations, but for critical
applications, measurements should be made under
simulated or actual working conditions.
Friction
Factor (F)
(FL) Standard Seals
(FP) Low Friction Seals

1
500
1000
1500
2000
2500
3000
Pressure (psi)
34


Low Friction Seals

Calculation of Running Friction
Sample Calculation
The seal friction attributable to the cylinder is calculated

as the sum of the friction due to the individual sealing
elements (wiperseal friction + rod seal friction + piston
seal friction), using the following formulae:
Option:
Formula:
Standard rod and piston seals
12d + 12 FLd + 24 FLD
Series RDH Cylinder with 3.25 dia. bore and 1.75 dia.
piston rod with low friction seals at 1500 psi.
Running Friction Calculation:
Friction (lbs. force) 12d + 30Fpd + 6FpD
Friction (lbs. force) 12 (1.75) + 30 (1.3 x 1.75)

+ 6 (1.3 x 3.25)
Low friction rod and piston seals 12d + 30 Fpd + 6 FpD
Friction (lbs. force) 115
Where: d = rod dia. (inch)

D = bore dia. (inch)
FL = friction factor for standard seals (FL)
Fp = friction factor for PTFE low friction seals (Fp)
Breakaway Friction Calculation:

Fp x 1.0 Fp
Based on zero pressure:
Breakaway Friction
Friction (lbs. force) 12d + 30Fpd + 6FpD
Breakaway friction may be calculated by applying the

following correction factors:
Friction (lbs. force) 12 (1.75) + 30 (.3 x 1.75)

+ 6 (.3 x 3.25)
Correction factors
Standard seals:
FL x 1.5
Low friction seals: Fp x 1.0
Friction (lbs. force) 43

Specifications for Low Friction Options:
Operating Pressure: 0 - 3000 psi
Operating Temperature: -10F to +165F.

For higher temperatures, consult factory.
Fluid Media: petroleum-based hydraulic oils.

For other fluids, consult factory.
35


Series RDH Common Modifications
Metric Piston Rod Thread
The following modifications can be supplied on most

Series RDH cylinders for an additional charge.
The table below lists the standard thread supplied when

Piston Rod Thread Type M is specified in the cylinder
model code with Piston Rod Ends 4, 8 and 9. For Style
7M, see page 15 for details.
Metallic Rod Wiper
When specified, metallic rod wipers can be supplied

instead of the standard urethane wiperseal. Recommended in applications where contaminants tend to
cling to the extended piston rod and would damage the
standard urethane wiperseal. Installation of metallic rod
wiper does not affect cylinder dimensions.
MM
Rod
(inches)
0.625
1.000
1.375
1.750
2.000
2.500
3.000
3.500
4.000
4.500
5.000
5.500
Air Bleeds
In most hydraulic circuits, cylinders are considered

self-bleeding when cycled full stroke. If air bleeds are
required and specified, Air Bleed Ports for venting air
can be provided at both ends of the cylinder body, or
on the head or cap. To order, specify Bleed Port and
indicate the desired position on the cylinder.
Rod End Boots
Cylinders have a hardened bearing surface on the

piston rod to resist external damage and are equipped
with the high efficiency wiperseal to remove external
dust and dirt. Exposed piston rods that are subjected to
contaminants with air hardening properties, such as
paint, should be protected. In such applications, the use
of a collapsing cover should be considered. This is
commonly referred to as a rod boot. Calculate the
longer rod end required to accommodate the collapsed
length of the boot from the following data.
Style
8M
CC
M10x1.5
M20x1.5
M26x1.5
M33x2
M39x2
M48x2
M58x2
M64x2
M76x2
M80x2
M90x2
M100x2
M12x1.5
M22x1.5
M30x2
M39x2
M45x2
M56x2
M68x2
M76x2
M95x2
M110x2
M110x2
M130x2
A
Thread
Length
(inches)
0.75
1.13
1.63
2.00
2.25
3.00
3.50
3.50
4.00
4.50
5.00
5.50
Rectangular Head and Cap Flanges
Rectangular head flanges and cap flanges that matchmount NFPA Style ME5 and ME6 are available as a
special modification. Enter S for Special Modification
in the cylinder model code, request the desired flange in
the item notes and consult the factory for a quote.
Welded Rod End Accessories
LF .13 .13 .13 .13 .13 .13 .13 .10 .10 .10 .10 .10
OD 2.25 2.25 2.63 3.00 3.38 3.75 4.38 5.13 5.63 6.25 7.00 7.50
MM .500 .625 1.000 1.380 1.750 2.000 2.500 3.000 3.500 4.000 5.000 5.500
To determine extra length of
.50
piston rod required to
accommodate boot, calculate:
BL = Stroke x LF + 1.13"
BL + W + A = length of piston rod
to extend beyond the head face.
Note: Check all Boot O.Ds
against E dimension from
catalog.
Thread Size
Styles
4M & 9M
KK
Some standard and special rod end accessories can

be welded to the piston rod. In the cylinder model code,
specify "3" in the Piston Rod Thread Style field (for
special rod end). Then describe the accessory in the
item notes (or furnish a dimensioned sketch), signify that
it is welded to the piston rod and consult the factory for
a quote.
.63
MM OD
Additional common and custom

modifications are available, see Custom
Options and Modifications page or consult
the factory.
BL
Stroke Adjusters
For the requirement where adjusting the stroke is

specified. Several designs are available.
A retracting stroke adjuster must be ordered with an
S for Special Modification in the model code, and the
length of the adjustment must be specified.
Infrequent-type is defined by positioning the retract
stroke in a couple of attempts at original machine set
up. The frequent-type stroke adjuster is recommended
for adjustments required after the equipment has been
adjusted by the original machine manufacturer.
36


ALS Switch
Switches Mounted on Series RDH Cylinders

Add Value to Your Machine Design
Non-intrusive design eliminates the possibility
of oil leakage
Utilizes the standard carbon steel cylinder
body
Switches and cylinder combine to form a

compact package
Body-mounted switches are easily adjustable
along cylinder stroke length
Low profile switches are less prone to
mechanical damage
Series RDH Cylinder
with magnetic piston
Durable polyurethane
bi-directional seal for
positive sealing with no
by-pass and long life.
Cylinder Body
Standard carbon steel
material for ALS Switch.
WearGard wear ring

improves resistance to bearing
loads and provides support for
magnet.
37


ALS Switch Specifications
ALS Switch Wiring and Installation

For magnetic piston sensing through steel
tube material
4 wire DC connection
PNP and NPN versions can be wired N.O.
or N.C.
The ALS Switch is not designed for use with

non-ferrous tubes
CE approved
ATEX approved version available
Switch Operation
The switching zone may be up to 21mm wide

depending on tube wall thickness and piston speed.
The switch detects a change in polarity of the magnetic

field as a piston with magnet moves through the
cylinder.
LED Indicators
Formatting
There are two LEDs (yellow and red) to indicate that

the piston is inside or outside the switching zone. The
sequence of the LEDs is determined by the orientation
of the north pole of the magnet system (rod end side of
single rod end cylinders) to the connector.
Before the switch is used for the first time, the piston
with magnet should be run in and out of the cylinder
to format the cylinder tube. The switch will detect the
polarity of the residual magnetic field created by the
movement of the magnetic piston during formatting.
When the ALS Switch connector faces the rod side of

single rod end cylinders the red LED turns ON when
the piston is within the switching zone. The yellow LED
is ON otherwise.
Field Direction with Magnetic Piston
Single rod end cylinders are assembled with the

piston magnets North Pole facing the rod end. As the
magnetic piston moves through the cylinder, it creates
a stronger field opposite in polarity to the residual
magnetism in the cylinder tube. As it moves under the
switch, the change in polarity of the magnetic field in
the cylinder tube is detected.
When the ALS Switch connector faces the cap side of

single rod end cylinders the yellow LED turns ON when
the piston is within the switching zone. The red LED is
ON otherwise.
Performance
Switch Zone
ALS Switches have been designed to operate at a

maximum piston speed of 0.5m/s, and a maximum
cylinder operating temperature of 85C.
Switch actuation occurs as the piston enters a

switching zone. The switching point is highly
repeatable, in either direction, under conditions of
constant piston speed and operating temperature.
Specifications
Note: ALS Switches are designed to sense near end

of stroke positions (stroke-to-go) and stroke positions
in between these two points. For true end-of-stroke
position sensing, use the CLS-A or EPS-A Limit
Switches featured on the EPS-A Sensors / CLS-A
Switches page.
Switching Output:
Hysteresis :
1
7.2
50.0
TARGET
AREA
64.0
YELLOW
LED
A2
Brown
(+)
Black
White
Blue
Load Current:
100mA
Voltage Drop:
ALS-P
RED
LED
0.5mm
Leakage Current:
10.5
18.0
5mm
Repeatability :
1
21.0
PNP or NPN
< 10A
< 1.5 VDC
Short Circuit and

Overload Protection:
Yes
Reverse Polarity
Protection:
Yes
Supply Voltage:
10 - 30 VDC
LED(s):
Yes (2)
Current Consumption:
< 30 mA
N.O. Load
N.C. Load
(-)
Operating
Temperature Range:
M12x1.0 METRIC THREAD
-25C to +85C
(-13F to +185F)
Housing Material: Black Polyamide (PA)
ALS Switch output states may be influenced by an

external magnetic field. Care must be taken to avoid
external magnetic field exposure.
Enclosure Rating:
IP67
Hysteresis and repeatability based on measurements

with a cylinder outer diameter of 46mm, wall thickness
of 3mm and piston speed of 0.5m/s.
1
38


ALS Switch Wiring Connection
ALS Switch Wiring and Installation

Because the ALS Switch detects change in polarity
as the magnet moves through the cylinder, wiring
connections are dependent on switch mounting
orientation to the magnets North Pole. The two possible
orientations are:
Connections to Pin 1 (+VDC) and Pin 3 (-VDC) are the

same for either switch orientation. But, as outlined in
the table and wiring schematic diagrams below, the
normal output state of Pins 2 & 4 flip between mounting orientations A & B. Note that to sense near the fully
retracted position of the cylinder the cap end switch must
be mounted in orientation A, and to sense near the fully
extended position of the cylinder the rod end switch must
be mounted in orientation B.
A connector facing toward the rod end

(rod end 1 if K-type)
B connector facing toward the cap end

(rod end 2 if K-type)
General view of switches as installed:

B
Example: An application requires that ALS Switches

sense two positions of the cylinder with normally closed
logic at both ends. How would the switches be wired?
Answer: The two switches would not be installed or
wired the same way. The cap end switch would be
installed in orientation A with Pin 1 (+VDC), Pin 2 (Load),
Pin 3 (-VDC), Pin 4 (not used). The rod end switch would
be installed in orientation B with Pin 1 (+VDC), Pin 2 (not
used), Pin 3 (-VDC), Pin 4 (Load).
LED Function and Pin Wiring

Switch
Mounting
Orientation
Connector
Facing Toward
LED indicator (on/off)

when magnet is:
Pin
Wire
Function
1
2
3
4
1
2
3
4
Brown
White
Blue
Black
Brown
White
Blue
Black
+VDC
N.C.
-VDC
N.O.
+VDC
N.O.
-VDC
N.C.
Single Rod Double Rod Out of Switch Zone In Switch Zone

Cylinder
Cylinder
Red
Yellow
Red Yellow
Rod End
Cap End
Rod End #1
Rod End #2
Switch Orientation A
(+)
4 BLACK
on
on
off
off
N.C. LOAD
(-)
Switch Orientation B
4 BLACK
2 WHITE
3 BLUE
NPN
Switch Orientation A
1 BROWN
3 BLUE
1 BROWN
(+)
(-)
(+)
N.C. LOAD
4 BLACK
N.O. LOAD
2 WHITE
N.C. LOAD
N.O. LOAD
on
Switch Orientation B
(+)
1 BROWN
off
N.O. LOAD
4 BLACK
N.C. LOAD
2 WHITE
N.O. LOAD
2 WHITE
3 BLUE
on
ALS Switch Wiring Connection

12mm Connector
PNP
1 BROWN
off
(-)
3 BLUE
39
(-)


ALS Switch Part Numbers
ALS Switch and Accessory Part Numbers
All switches have a 4-pin male M12x1 threaded connector.

Body mounting band for ALS switches must be ordered separately.
Minimum Net Stroke for ALS Switch
Switch Part Number
Bore
Stroke
1.50
3.00
2.00
3.00
2.50
2.88
Body Mounting Band Part Number
3.25
2.75
Bore
Part Number
4.00
2.63
5.00
2.38
1.50
0965360150
6.00
2.19
2.00
0965360200
PNP
NPN
0944520000
0942230000
Note: Specify piston code 7 in cylinder model number when using

ALS Switches.
2.50
0965360250
3.25
0965360325
4.00
0965360400
5.00
0965360500
6.00
0965630600
12mm Cordset for ALS Switches
12mm Cordset with Female Quick Connect

M12 Straight Connector
M12 Right Angle Connector
Cable Length
Part Number
Cable Length
Part Number
5 meters
9126487205
5 meters
9126487305
2 meters
9126487202
2 meters
9126487302
Straight Connector
A female connector is available for all switches with

the male 12mm quick connect option. The cordsets
are available with a right angle or straight connector.
Cordset part numbers are listed above.
CABLE LENGTH (m)

(SEE TABLE)
42
PIN 2 / WHT
PIN 3 / BLU
14.5
Cordset Specifications
Connector Polyvinylchloride (PVC) body
material, PVC contact carrier,
spacing to VDE 0110 Group C,
(250VAC / 300VDC)
Contacts Gold Plated Copper Tin (CuSn),
stamped from stock.
Coupling Method Threaded nut: Chrome plated
brass.
Cord Construction PVC non-wicking, non-hygroscopic,
250VAC / 300VDC. Cable end is
stripped.
Conductors Extra high flex stranding with PVC
insulation
Temperature -13F to 158F (-25C to 70C)
Protection NEMA 1, 3, 4, 6P and IEC 1P67
Cable Length 6.56 ft (2m) or 16.4 ft (5m)
1.5
PIN 4 / BLK M12 X 1

CABLE MINIMUM BEND
RADIUS: 100mm
PIN 1 / BRN
Right Angle Connector

PIN 2 / WHT
14.5
PIN 1 / BRN
PIN 3 / BLU
PIN 4 / BLK
38.3
26.5
CABLE MINIMUM
BEND RADIUS:
100mm
CABLE LENGTH
(SEE TABLE)
1.5
M12 X 1
40


EPS-A Sensors / CLS-A Switches
EPS-A Threaded Style End-Of-Stroke Inductive Proximity Sensor
Non-contacting, end-of-stroke position sensor
Note: Cylinders that include EPS-A Switches

may be longer than standard cylinders.
Consult Switch dimension tables for
exact lengths.
Minor voltage drop and leakage current

CE, C-UL-US Approved
IP68 rating
4-pin 12mm connector (standard)
Cable and short cable/connector options
Shouldered one-piece stainless steel body for positive

installation and easy replacement
PNP (sourcing) output
Normally Open function
10-30 VDC
CLS-A Threaded Style End-Of-Stroke Limit Switches

Non-contacting, magnetically-actuating
In the Operated position a ferrous part (piston or piston

spacer) enters the sensing area and attracts the magnet
assembly which causes the rod to draw the contacts
together.
As shown in the illustrations below, these switches

are magnetically operated. Dual magnets provide a
dependable snap action for positive position sensing.
In the Unoperated position, the magnet assembly is
attracted in the opposite direction of the arrow, causing
a finely ground stainless steel connecting rod to hold
the contacts open.
Threaded switches can be height-adjusted for small

changes to end-of-stroke position sensing.
Note: Cylinders that include CLS-A Switches may
be longer than standard cylinders. Consult Switch
Dimension tables for exact lengths.
Operating Principle
Magnet Assy
Switch Case
Connecting Rod
Differential
Sensing
Area
Sensing
Distance
N/O
N
N/C
N/O
Ferrous
Actuator
N/C
Com.
Com.
Operated
Unoperated
See the specification table on the next page for additional details.
41
Sensing gap: .030" to .060"

Trip point: Factory set with
piston bottomed out.
Release point: Approx. 0.250"
of piston travel.
Minimum net stroke is 0.500"
for 1.50" and 2.00" bores and
0.750" for larger bores.


EPS-A Sensor / CLS-A Switch Specifications Common Modifications
EPS-A Sensor & CLS-A Limit Switch Specifications

Switch Type:
Inductive Proximity
Non-contacting, magnetically actuating
EPS-A
CLS-A
General Purpose, 3 wire,

DC Sensor
For applications where the customer

needs NO or NC contacts, zero
leakage, zero voltage drop, higher or
lower load current than EPS style.
Threaded style permits small adjustability
of make/break location.
10 to 30 VDC
24 to 240 VAC/DC
Style:
Code Designator:
Description:
Supply Voltage:
Load Current, max.:
4 AMPS @ 120 VAC
200 mA
3 AMPS @ 24 VDC
Leakage Current:
10 A
None
Voltage Drop:
2.0 V
None
-13F to +194F
-40F to +221F
Operating Temperature:
0961710000 - 1.50" Bore
Part Number:
0961640M12
Connection:
M12 4-pin connector
3-pin micro connector
Enclosure IP68
Enclosure IP68
LED Indication:
No
No
Short Circuit Protection:
Yes
No
RFI/Weld Field Immune:
No
Yes
PNP
SPDT (Single Pole Double Throw),

Normally Open/Normally Closed,
Form C
CE
UL Listed General Purpose
0.25" from end of stroke typical.

Tolerance is +0 / -0.13"
0.25" from end of stroke typical.

Tolerance is +0 / -0.13"
Enclosure Rating:
Output:
Approvals/Marks:
Make/Break Location:
Wiring Instructions:
bn
bk
bu
0961680000 - 2.00" - 8.00" Bores
+
DC
3
2
Pin 1
Com
Pin 2
N/C
Pin 3
N/O
" conduit hub, cable, flying lead

and other connector types
Options:
(Consult factory)
5m cable
High temperature version (to +400F)

ATEX, CSA, intrinsically-safe,
explosion-proof, non-incendive,
DPDT and Subsea versions
42


How to Order EPS & CLS Limit Switches
EPS-A & CLS-A limit switches may be ordered as

follows:
1) Complete the basic cylinder model number.
5) Limit Switch Code Specify letter prefix C for

EPS-A or G for CLS-A, then fill in the four blanks
specifying port location, switch location and actuation
point for both head and cap. If only one switch is
used, place XXXX in the unused blanks.
2) Place an S in the model number for Special

Modification.
3) Mounting styles DD, J and H should be used with
caution because of possible mounting interferences.
Example = G13GG-XXXX denotes a switch on the

head end only.
4) Special modifications to cylinders other than

switches must be described in the item notes.
Example = XXXX-G42GG denotes a switch on the cap

end only.
Limit Switch Code

Head End
Cap End
GG
GG
Specify:
C = EPS-A
G = CLS-A
T =
Prepared
for CLS-A
Threaded
Switch
X = Special
installed
switch
(Specify)
Port
Location
See
Figure 1.
Switch
Location
See
Figure 1.
Actuation
Point
GG = End
of Stroke.
Port
Location
See
Figure 1.
Switch
Location
See
Figure 1.
Actuation
Point
GG = End
of Stroke.
Note: All specified switch and port locations are as seen from rod end of cylinder.
Figure 1
C
4
Head (Rod) End
43
Head
Cap


Dimensions Cylinders with Limit Switches Common Modifications
Series RDH cylinders with Limit Switches require

additional length for the piston collar(s) required to activate
the switch. The table below and those on following pages
show dimensions that are changed when switches are
Switch on Both Ends

EN
specified. Note that dimension changes are specific to

whether switches are specified on both ends, switch on
cap end only or switch on head end only.
ER
HS
EN
HS
HS
Styles T & DD
HS
Styles B
& BB
P + STROKE
LB + STROKE
ZJ + STROKE
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
EN
ER
HS
HS
Styles SB
& SBM
Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
All Mountings
ER
0.83
0.83
1.12
1.12
1.31
1.31
1.31
1.68
1.68
1.68
1.44
1.44
1.44
1.79
1.79
1.79
1.79
2.36
2.36
2.36
2.36
2.67
2.67
2.67
2.67
2.67
2.96
2.96
2.96
2.96
2.96
HS
ER
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
All Mountings
Except Styles J/JP
EN
Add Stroke
CLS-A EPS-A CLS-A EPS-A LB

4.49
2.66
1.63
1.63
4.19
4.49
2.66
2.01
2.01
4.56
4.25
2.91
2.31
2.20
5.69
4.25
2.91
2.31
2.20
5.69
4.47
3.13
2.56
2.45
6.13
2.45
6.13
4.47
3.13
2.56
4.47
3.13
2.56
2.45
6.13
4.84
3.51
2.81
2.70
6.88
4.84
3.51
2.81
2.70
6.88
4.84
3.51
2.81
2.70
6.88
5.15
3.82
3.06
2.95
7.25
5.15
3.82
3.06
2.95
7.25
5.15
3.82
3.06
2.95
7.25
5.59
4.26
3.31
3.20
7.87
5.59
4.26
3.31
3.20
7.87
5.59
4.26
3.31
3.20
7.87
5.59
4.26
3.31
3.20
7.87
6.09
4.76
3.19
3.14
8.37
6.09
4.76
3.19
3.14
8.37
6.09
4.76
3.19
3.14
8.37
6.09
4.76
3.19
3.14
8.37
6.59
5.26
3.20
3.08
9.00
6.59
5.26
3.20
3.08
9.00
6.59
5.26
3.20
3.08
9.00
6.59
5.26
3.20
3.08
9.00
6.59
5.26
3.20
3.08
9.00
7.09
5.76
3.41
3.29
9.50
7.09
5.76
3.41
3.29
9.50
7.09
5.76
3.41
3.29
9.50
7.09
5.76
3.41
3.29
9.50
7.09
5.76
3.41
3.29
9.50
P
1.82
1.82
2.81
2.81
2.75
2.75
2.75
2.94
2.94
2.94
3.25
3.25
3.25
3.31
3.31
3.31
3.31
3.00
3.00
3.00
3.00
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
44
Styles
T & DD
Styles
B & BB
Style SB
Style SBM
Add
Stroke
ZJ
4.75
5.25
6.38
6.50
6.81
7.06
6.94
7.69
7.88
7.81
8.19
8.31
8.25
8.87
8.93
8.93
8.93
9.43
9.43
9.43
9.43
10.06
10.19
10.06
10.06
10.19
10.56
10.68
10.56
10.68
10.68
Add Stroke
Add Stroke
Add Stroke
XC
5.50
6.00
7.63
7.75
8.06
8.31
8.19
9.19
9.38
9.31
10.31
10.44
10.37
11.12
11.18
11.18
11.18
11.93
11.93
11.93
11.93
13.06
13.19
13.06
13.06
13.19
13.81
13.93
13.81
13.93
13.93
XC
5.50
6.00
7.63
7.75
8.06
8.31
8.19
9.19
9.38
9.31
10.31
10.44
10.37
11.12
11.18
11.18
11.18
11.93
11.93
11.93
11.93
XC
5.73
6.23
7.60
7.72
8.31
8.56
8.43
9.58
9.76
9.70
10.47
10.59
10.53
11.70
11.76
11.76
11.76
13.05
13.05
13.05
13.05
14.63
14.75
14.63
14.63
14.75
15.12
15.25
15.12
15.25
15.25
ZC
6.00
6.50
8.38
8.50
8.81
9.06
8.94
10.19
10.38
10.31
11.69
11.81
11.75
12.87
12.93
12.93
12.93
13.93
13.93
13.93
13.93
15.56
15.69
15.56
15.56
15.69
16.56
16.68
16.56
16.68
16.68
ZC
6.25
6.75
8.63
8.75
9.06
9.31
9.19
10.44
10.63
10.56
12.19
12.31
12.25
13.62
13.68
13.68
13.68
14.43
14.43
14.43
14.43
N/A
ZC
6.87
7.38
8.89
9.02
9.88
10.13
10.01
11.55
11.73
11.67
12.91
13.03
12.97
14.85
14.91
14.91
14.91
16.99
16.99
16.99
16.99
18.57
18.69
18.57
18.57
18.69
19.85
19.97
19.85
19.97
19.97


Switch on Both Ends

EJ
EN
ER
HS2
HS2
HS2
HS2
Style H1
Styles J/JP1
YF
P + STROKE
LH + STROKE
XF + STROKE
ZF + STROKE
PJ + STROKE
LG + STROKE
ZG + STROKE
EN
ER
HS2
Style TT
Bore Rod
No.
MM
Rod
EH
All Mountings
Except Styles J/JP
HS2
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
Styles J/JP
EN
Add
EJ
ER YF
Add Stroke
Stroke
CLS-A EPS-A P CLS-A EPS-A
LG PJ ZG
1 (std) 0.625 1.63 1.63 1.82 2.01 2.01 0.83 2.75 4.56 1.82 5.37
1.50
2 1.000 2.01 2.01 1.82 2.01 2.01 0.83 3.25 4.56 1.82 5.88
1 (std) 1.000 2.31 2.20 2.81 2.44 2.33 1.12 3.26 5.81 2.81 6.75
2.00
2 1.375 2.31 2.20 2.81 2.44 2.33 1.12 3.38 5.81 2.81 6.87
1 (std) 1.000 2.56 2.45 2.75 2.69 2.58 1.31 3.44 6.25 2.75 7.19
2.50
2 1.750 2.56 2.45 2.75 2.69 2.58 1.31 3.69 6.25 2.75 7.44
3 1.375 2.56 2.45 2.75 2.69 2.58 1.31 3.56 6.25 2.75 7.31
1 (std) 1.375 2.81 2.70 2.94 2.94 2.83 1.68 3.81 7.00 2.94 8.06
3.25
2 2.000 2.81 2.70 2.94 2.94 2.83 1.68 4.00 7.00 2.94 8.25
3 1.750 2.81 2.70 2.94 2.94 2.83 1.68 3.94 7.00 2.94 8.19
1 (std) 1.750 3.06 2.95 3.25 3.06 2.95 1.44 4.15 7.25 3.25 8.44
4.00
2 2.500 3.06 2.95 3.25 3.06 2.95 1.44 4.27 7.25 3.25 8.56
3 2.000 3.06 2.95 3.25 3.06 2.95 1.44 4.21 7.25 3.25 8.50
1 (std) 2.000 3.31 3.20 3.31 3.25 3.14 1.79 4.45 7.80 3.31 9.12
2 3.500 3.31 3.20 3.31 3.25 3.14 1.79 4.51 7.80 3.31 9.18
5.00
3 2.500 3.31 3.20 3.31 3.25 3.14 1.79 4.51 7.80 3.31 9.18
4 3.000 3.31 3.20 3.31 3.25 3.14 1.79 4.51 7.80 3.31 9.18
1 (std) 2.500 3.19
3.14
3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18
2 4.000 3.19
3.14
3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18
6.00
3 3.000 3.19
3.14
3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18
4 3.500 3.19
3.14
3.00 3.56 3.51 2.36 4.99 8.75 3.00 10.18
1 (std) 3.000 3.20 3.08 3.25 3.82 3.70 2.67 5.25 9.63 3.25 11.06
2 5.000 3.20 3.08 3.25 3.82 3.70 2.67 5.38 9.63 3.25 11.19
7.00
3 3.500 3.20 3.08 3.25 3.82 3.70 2.67 5.25 9.63 3.25 11.06
4 4.000 3.20 3.08 3.25 3.82 3.70 2.67 5.25 9.63 3.25 11.06
5 4.500 3.20 3.08 3.25 3.82 3.70 2.67 5.38 9.63 3.25 11.19
1 (std) 3.500 3.41 3.29 3.25 3.91 3.79 2.96 5.44 10.00 3.25 11.56
2 5.500 3.41 3.29 3.25 3.91 3.79 2.96 5.56 10.00 3.25 11.68
8.00
3 4.000 3.41 3.29 3.25 3.91 3.79 2.96 5.44 10.00 3.25 11.56
4 4.500 3.41 3.29 3.25 3.91 3.79 2.96 5.56 10.00 3.25 11.68
5 5.000 3.41 3.29 3.25 3.91 3.79 2.96 5.56 10.00 3.25 11.68
1
See port and switch position note on mounting Styles J/JP & H pages.
2
See previous page for HS dimensions.
45
Style H
EH
1.08
1.08
1.43
1.43
1.68
1.68
1.68
2.18
2.18
2.18
2.07
2.07
2.07
2.54
2.54
2.54
2.54
3.24
3.24
3.24
3.24
3.55
3.55
3.55
3.55
3.55
3.96
3.96
3.96
3.96
3.96
Add Stroke
LH
4.06
4.44
5.56
5.56
6.00
6.00
6.00
6.75
6.75
6.75
7.12
7.12
7.12
7.74
7.74
7.74
7.74
8.25
8.25
8.25
8.25
8.88
8.88
8.88
8.88
8.88
9.37
9.37
9.37
9.37
9.37
XF ZF
4.62 5.00
5.13 5.50
6.25 6.69
6.37 6.81
6.69 7.19
6.94 7.44
6.81 7.31
7.56 8.19
7.75 8.38
7.69 8.31
8.06 8.81
8.19 8.94
8.12 8.87
8.74 9.62
8.80 9.68
8.80 9.68
8.80 9.68
9.31 10.31
9.31 10.31
9.31 10.31
9.31 10.31
9.94 10.94
10.06 11.06
9.94 10.94
9.94 10.94
10.06 11.06
10.43 11.56
10.56 11.68
10.43 11.56
10.56 11.68
10.56 11.68
Style TT
ER
0.83
0.83
1.12
1.12
1.31
1.31
1.31
1.68
1.68
1.68
1.44
1.44
1.44
1.79
1.79
1.79
1.79
2.36
2.36
2.36
2.36
2.67
2.67
2.67
2.67
2.67
2.96
2.96
2.96
2.96
2.96
Add Stroke
LB
4.19
4.56
5.69
5.69
6.13
6.13
6.13
6.88
6.88
6.88
7.25
7.25
7.25
7.87
7.87
7.87
7.87
8.37
8.37
8.37
8.37
9.00
9.00
9.00
9.00
9.00
9.50
9.50
9.50
9.50
9.50
XC ZC
5.37 6.00
5.88 6.50
7.00 7.63
7.12 7.75
7.56 8.31
7.81 8.56
7.69 8.44
8.62 9.56
8.81 9.75
8.75 9.69
9.19 10.19
9.31 10.31
9.25 10.25
10.24 11.62
10.30 11.68
10.30 11.68
10.30 11.68
10.9312.43
10.9312.43
10.9312.43
10.9312.43
11.94 13.81
12.0613.94
11.94 13.81
11.94 13.81
12.0613.94
12.56 14.56
12.68 14.68
12.56 14.56
12.68 14.68
12.68 14.68


Switch on Head End

EN
EN
HS
HS
Styles B
& BB
Styles T & DD
P + STROKE
LB + STROKE
ZJ + STROKE
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
EN
HS
Styles SB
& SBM
Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
All Mountings
HS
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
All Mountings
Except Styles J/JP
Styles
T & DD
Styles
B & BB
Style SB
Style SBM
EN
Add
Stroke
ZJ
4.62
5.13
6.25
6.37
6.69
6.94
6.81
7.56
7.75
7.69
8.19
8.31
8.25
8.87
8.93
8.93
8.93
9.43
9.43
9.43
9.43
10.06
10.19
10.06
10.06
10.19
10.56
10.68
10.56
10.68
10.68
Add Stroke
Add Stroke
Add Stroke
Add Stroke
CLS-A EPS-A CLS-A EPS-A

4.49
2.66
1.63
1.63
4.49
2.66
2.01
2.01
4.25
2.91
2.31
2.20
4.25
2.91
2.31
2.20
4.47
3.13
2.56
2.45
4.47
3.13
2.56
2.45
4.47
3.13
2.56
2.45
4.84
3.51
2.81
2.70
4.84
3.51
2.81
2.70
4.84
3.51
2.81
2.70
5.15
3.82
3.06
2.95
5.15
3.82
3.06
2.95
5.15
3.82
3.06
2.95
5.59
4.26
3.31
3.20
5.59
4.26
3.31
3.20
5.59
4.26
3.31
3.20
5.59
4.26
3.31
3.20
6.09
4.76
3.19
3.14
6.09
4.76
3.19
3.14
6.09
4.76
3.19
3.14
6.09
4.76
3.19
3.14
6.59
5.26
3.20
3.08
6.59
5.26
3.20
3.08
6.59
5.25
3.20
3.08
6.59
5.26
3.20
3.08
6.59
5.26
3.20
3.08
7.09
5.76
3.41
3.29
7.09
5.76
3.41
3.29
7.09
5.76
3.41
3.29
7.09
5.76
3.41
3.29
7.09
5.76
3.41
3.29
LB
4.06
4.44
5.56
5.56
6.00
6.00
6.00
6.75
6.75
6.75
7.25
7.25
7.25
7.87
7.87
7.87
7.87
8.37
8.37
8.37
8.37
9.00
9.00
9.00
9.00
9.00
9.50
9.50
9.50
9.50
9.50
P
1.69
1.69
2.68
2.68
2.63
2.63
2.63
2.81
2.81
2.81
3.25
3.25
3.25
3.31
3.31
3.31
3.31
3.00
3.00
3.00
3.00
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
46
XC
5.37
5.88
7.50
7.62
7.94
8.19
8.06
9.06
9.25
9.19
10.31
10.44
10.37
11.12
11.18
11.18
11.18
11.93
11.93
11.93
11.93
13.06
13.19
13.06
13.06
13.19
13.81
13.93
13.81
13.93
13.93
ZC
5.87
6.38
8.25
8.37
8.69
8.94
8.81
10.06
10.25
10.19
11.69
11.81
11.75
12.87
12.93
12.93
12.93
13.93
13.93
13.93
13.93
15.56
15.69
15.56
15.56
15.69
16.56
16.68
16.56
16.68
16.68
XC
5.37
5.88
7.50
7.62
7.94
8.19
8.06
9.06
9.25
9.19
10.31
10.44
10.37
11.12
11.18
11.18
11.18
11.93
11.93
11.93
11.93
ZC
6.12
6.63
8.50
8.62
8.94
9.19
9.06
10.31
10.50
10.44
12.19
12.31
12.25
13.62
13.68
13.68
13.68
14.43
14.43
14.43
14.43
N/A
XC
5.61
6.11
7.47
7.59
8.18
8.43
8.31
9.45
9.64
9.58
10.47
10.59
10.53
11.70
11.76
11.76
11.76
13.05
13.05
13.05
13.05
14.63
14.75
14.63
14.63
14.75
15.12
15.25
15.12
15.25
15.25
ZC
6.75
7.25
8.77
8.89
9.76
10.01
9.88
11.42
11.61
11.55
12.91
13.03
12.97
14.85
14.91
14.91
14.91
16.99
16.99
16.99
16.99
18.57
18.69
18.57
18.57
18.69
19.85
19.97
19.85
19.97
19.97


Switch on Head End

EJ
EN
HS2
HS2
Style H1
Styles J/JP1
YF
P + STROKE
LH + STROKE
XF + STROKE
ZF + STROKE
PJ + STROKE
LG + STROKE
ZG + STROKE
EN
HS2
Style TT
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
Bore
Rod
No.
MM
Rod
All Mountings
Except Styles J/JP
Styles J/JP
EN
Add
EJ
YF
Add Stroke
Stroke
CLS-A EPS-A
P
CLS-A EPS-A
LG
PJ
ZG
1 (std) 0.625 1.63
1.63
1.69
2.01
2.01 2.75 4.44 1.69 5.25
1.50
2
1.000 2.01
2.01
1.69
2.01
2.01 3.25 4.44 1.69 5.75
1 (std) 1.000 2.31
2.20
2.68
2.44
2.33 3.26 5.69 2.68 6.63
2.00
2
1.375 2.31
2.20
2.68
2.44
2.33 3.38 5.69 2.68 6.75
1 (std) 1.000 2.56
2.45
2.63
2.69
2.58 3.44 6.13 2.63 7.06
2.50
2
1.750 2.56
2.45
2.63
2.69
2.58 3.69 6.13 2.63 7.31
3
1.375 2.56
2.45
2.63
2.69
2.58 3.56 6.13 2.63 7.19
1 (std) 1.375 2.81
2.70
2.81
2.94
2.83 3.81 6.88 2.81 7.94
3.25
2
2.000 2.81
2.70
2.81
2.94
2.83 4.00 6.88 2.81 8.13
3
1.750 2.81
2.70
2.81
2.94
2.83 3.94 6.88 2.81 8.06
1 (std) 1.750 3.06
2.95
3.25
3.06
2.95 4.15 7.25 3.25 8.44
4.00
2
2.500 3.06
2.95
3.25
3.06
2.95 4.27 7.25 3.25 8.56
3
2.000 3.06
2.95
3.25
3.06
2.95 4.21 7.25 3.25 8.50
3.20
3.31
3.25
3.14 4.45 7.80 3.31 9.12
1 (std) 2.000 3.31
2
3.500 3.31
3.20
3.31
3.25
3.14 4.51 7.80 3.31 9.18
5.00
3
2.500 3.31
3.20
3.31
3.25
3.14 4.51 7.80 3.31 9.18
4
3.000 3.31
3.20
3.31
3.25
3.14 4.51 7.80 3.31 9.18
1 (std) 2.500 3.19
3.14
3.00
3.56
3.51 4.99 8.75 3.00 10.18
2
4.000 3.19
3.14
3.00
3.56
3.51 4.99 8.75 3.00 10.18
6.00
3
3.000 3.19
3.14
3.00
3.56
3.51 4.99 8.75 3.00 10.18
4
3.500 3.19
3.14
3.00
3.56
3.51 4.99 8.75 3.00 10.18
1 (std) 3.000 3.20
3.08
3.25
3.82
3.70 5.25 9.63 3.25 11.06
2
5.000 3.20
3.08
3.25
3.82
3.70 5.38 9.63 3.25 11.19
7.00
3
3.500 3.20
3.08
3.25
3.82
3.70 5.25 9.63 3.25 11.06
4
4.000 3.20
3.08
3.25
3.82
3.70 5.25 9.63 3.25 11.06
5
4.500 3.20
3.08
3.25
3.82
3.70 5.38 9.63 3.25 11.19
1 (std) 3.500 3.41
3.29
3.25
3.91
3.79 5.44 10.00 3.25 11.56
2
5.500 3.41
3.29
3.25
3.91
3.79 5.56 10.00 3.25 11.68
8.00
3
4.000 3.41
3.29
3.25
3.91
3.79 5.44 10.00 3.25 11.56
4
4.500 3.41
3.29
3.25
3.91
3.79 5.56 10.00 3.25 11.68
5
5.000 3.41
3.29
3.25
3.91
3.79 5.56 10.00 3.25 11.68
1
2
See previous page for HS dimensions.
47
Style H
Style TT
Add Stroke
Add Stroke
LH
3.94
4.31
5.44
5.44
5.88
5.88
5.88
6.63
6.63
6.63
7.12
7.12
7.12
7.74
7.74
7.74
7.74
8.25
8.25
8.25
8.25
8.88
8.88
8.88
8.88
8.88
9.37
9.37
9.37
9.37
9.37
XF
4.50
5.00
6.13
6.25
6.56
6.81
6.69
7.44
7.63
7.56
8.06
8.19
8.12
8.74
8.80
8.80
8.80
9.31
9.31
9.31
9.31
9.94
10.06
9.94
9.94
10.06
10.43
10.56
10.43
10.56
10.56
ZF
4.87
5.38
6.56
6.69
7.06
7.31
7.19
8.06
8.25
8.19
8.81
8.94
8.87
9.62
9.68
9.68
9.68
10.31
10.31
10.31
10.31
10.94
11.06
10.94
10.94
11.06
11.56
11.68
11.56
11.68
11.68
LB
4.06
4.44
5.56
5.56
6.00
6.00
6.00
6.75
6.75
6.75
7.25
7.25
7.25
7.87
7.87
7.87
7.87
8.37
8.37
8.37
8.37
9.00
9.00
9.00
9.00
9.00
9.50
9.50
9.50
9.50
9.50
XC
5.25
5.75
6.88
7.00
7.44
7.69
7.56
8.50
8.69
8.63
9.19
9.31
9.25
10.24
10.30
10.30
10.30
10.93
10.93
10.93
10.93
11.94
12.06
11.94
11.94
12.06
12.56
12.68
12.56
12.68
12.68

ZC
5.87
6.38
7.50
7.62
8.19
8.44
8.31
9.44
9.63
9.56
10.19
10.31
10.25
11.62
11.68
11.68
11.68
12.43
12.43
12.43
12.43
13.81
13.94
13.81
13.81
13.94
14.56
14.68
14.56
14.68
14.68

Switch on Cap End

ER
ER
HS
Styles T & DD
HS
Styles B
& BB
P + STROKE
LB + STROKE
ZJ + STROKE
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
ER
HS
Styles SB
& SBM
Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
All Mountings
Except Styles J/JP or H
ER
HS
0.83
0.83
1.12
1.12
1.31
1.31
1.31
1.68
1.68
1.68
1.44
1.44
1.44
1.79
1.79
1.79
1.79
2.36
2.36
2.36
2.36
2.67
2.67
2.67
2.67
2.67
2.96
2.96
2.96
2.96
2.96
CLS-A EPS-A
4.49
2.66
4.49
2.66
4.25
2.91
4.25
2.91
4.47
3.13
4.47
3.13
4.47
3.13
4.84
3.51
4.84
3.51
4.84
3.51
5.15
3.82
5.15
3.82
5.15
3.82
5.59
4.26
5.59
4.26
5.59
4.26
5.59
4.26
6.09
4.76
6.09
4.76
6.09
4.76
6.09
4.76
6.59
5.26
6.59
5.26
6.59
5.26
6.59
5.26
6.59
5.26
7.09
5.76
7.09
5.76
7.09
5.76
7.09
5.76
7.09
5.76
Add Stroke
LB
3.69
4.06
4.94
4.94
5.38
5.38
5.38
6.13
6.13
6.13
6.50
6.50
6.50
7.12
7.12
7.12
7.12
8.37
8.37
8.37
8.37
9.00
9.00
9.00
9.00
9.00
9.50
9.50
9.50
9.50
9.50
P
1.32
1.32
2.06
2.06
2.00
2.00
2.00
2.19
2.19
2.19
2.50
2.50
2.50
2.56
2.56
2.56
2.56
3.00
3.00
3.00
3.00
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
3.25
Styles
T & DD
Styles
B & BB
Style SB
Style SBM
Add
Stroke
ZJ
4.25
4.75
5.63
5.75
6.06
6.31
6.19
6.94
7.13
7.06
7.44
7.56
7.50
8.12
8.18
8.18
8.18
9.43
9.43
9.43
9.43
10.06
10.19
10.06
10.06
10.19
10.56
10.68
10.56
10.68
10.58
Add Stroke
Add Stroke
Add Stroke
48
XC
5.00
5.50
6.88
7.00
7.31
7.56
7.44
8.44
8.63
8.56
9.56
9.69
9.62
10.37
10.43
10.43
10.43
11.93
11.93
11.93
11.93
13.06
13.19
13.06
13.06
13.19
13.81
13.93
13.81
13.93
13.93
ZC
5.50
6.00
7.63
7.75
8.06
8.31
8.19
9.44
9.63
9.56
10.94
11.06
11.00
12.12
12.18
12.18
12.18
13.93
13.93
13.93
13.93
15.56
15.69
15.56
15.56
15.69
16.56
16.68
16.56
16.68
16.68
XC
5.00
5.50
6.88
7.00
7.31
7.56
7.44
8.44
8.63
8.56
9.56
9.69
9.62
10.37
10.43
10.43
10.43
11.93
11.93
11.93
11.93
ZC
5.75
6.25
7.88
8.00
8.31
8.56
8.44
9.69
9.88
9.81
11.44
11.56
11.50
12.87
12.93
12.93
12.93
14.43
14.43
14.43
14.43
N/A
XC
5.23
5.73
6.85
6.97
7.56
7.81
7.68
8.83
9.01
8.95
9.72
9.84
9.78
10.95
11.01
11.01
11.01
13.05
13.05
13.05
13.05
14.63
14.75
14.63
14.63
14.75
15.12
15.25
15.12
15.25
15.25
ZC
6.37
6.88
8.14
8.27
9.13
9.38
9.26
10.80
10.98
10.92
12.16
12.28
12.22
14.10
14.16
14.16
14.16
16.99
16.99
16.99
16.99
18.57
18.69
18.57
18.57
18.69
19.85
19.97
19.85
19.97
19.97


Switch on Cap End

EH
ER
HS
HS
Style H1
Styles J/JP1
YF
P + STROKE
LH + STROKE
XF + STROKE
ZF + STROKE
PJ + STROKE
LG + STROKE
ZG + STROKE
ER
HS
Style TT
P + STROKE
LB + STROKE
XC + STROKE
ZC + STROKE
Bore
Rod
No.
1 (std)
2
1 (std)
2.00
2
1 (std)
2
2.50
3
1 (std)
3.25
2
3
1 (std)
4.00
2
3
1 (std)
2
5.00
3
4
1 (std)
2
6.00
3
4
1 (std)
2
7.00
3
4
5
1 (std)
2
8.00
3
4
5
1.50
MM All Mountings
Rod
HS
CLS-A EPS-A
0.625 4.49
2.66
1.000 4.49
2.66
1.000 4.25
2.91
1.375 4.25
2.91
1.000 4.47
3.13
1.750 4.47
3.13
1.375 4.47
3.13
1.375 4.84
3.51
2.000 4.84
3.51
1.750 4.84
3.51
1.750 5.15
3.82
2.500 5.15
3.82
2.000 5.15
3.82
2.000 5.59
4.26
3.500 5.59
4.26
2.500 5.59
4.26
3.000 5.59
4.26
2.500 6.09
4.76
4.000 6.09
4.76
3.000 6.09
4.76
3.500 6.09
4.76
3.000 6.59
5.26
5.000 6.59
5.26
3.500 6.59
5.26
4.000 6.59
5.26
4.500 6.59
5.26
3.500 7.09
5.76
5.500 7.09
5.76
4.000 7.09
5.76
4.500 7.09
5.76
5.000 7.09
5.76
Styles J/JP
ER
0.83
0.83
1.12
1.12
1.31
1.31
1.31
1.68
1.68
1.68
1.44
1.44
1.44
1.79
1.79
1.79
1.79
2.36
2.36
2.36
2.36
2.67
2.67
2.67
2.67
2.67
2.96
2.96
2.96
2.96
2.96
YF
2.75
3.25
3.26
3.38
3.44
3.69
3.56
3.81
4.00
3.94
4.15
4.27
4.21
4.45
4.51
4.51
4.51
4.99
4.99
4.99
4.99
5.25
5.38
5.25
5.25
5.38
5.44
5.56
5.44
5.56
5.56
Style H
Add Stroke
LG
PJ
ZG
4.06 1.32 4.87
4.06 1.32 5.38
5.44 2.06 6.38
5.44 2.06 6.50
5.88 2.00 6.81
5.88 2.00 7.06
5.88 2.00 6.94
6.63 2.19 7.69
6.63 2.19 7.88
6.63 2.19 7.81
7.00 2.50 8.19
7.00 2.50 8.31
7.00 2.50 8.25
7.55 2.56 8.87
7.55 2.56 8.93
7.55 2.56 8.93
7.55 2.56 8.93
8.75 3.00 10.18
8.75 3.00 10.18
8.75 3.00 10.18
8.75 3.00 10.18
9.63 3.25 11.06
9.63 3.25 11.19
9.63 3.25 11.06
9.63 3.25 11.06
9.63 3.25 11.19
10.00 3.25 11.56
10.00 3.25 11.68
10.00 3.25 11.56
10.00 3.25 11.68
10.00 3.25 11.68
EH
1.08
1.08
1.43
1.43
1.68
1.68
1.68
2.18
2.18
2.18
2.07
2.07
2.07
2.54
2.54
2.54
2.54
3.24
3.24
3.24
3.24
3.55
3.55
3.55
3.55
3.55
3.96
3.96
3.96
3.96
3.96
LH
3.56
3.94
4.81
4.81
5.25
5.25
5.25
6.00
6.00
6.00
6.37
6.37
6.37
6.99
6.99
6.99
6.99
8.25
8.25
8.25
8.25
8.88
8.88
8.88
8.88
8.88
9.37
9.37
9.37
9.37
9.37
Add Stroke
P
XF
1.32 4.12
1.32 4.63
2.06 5.50
2.06 5.62
2.00 5.94
2.00 6.19
2.00 6.06
2.19 6.81
2.19 7.00
2.19 6.94
2.50 7.31
2.50 7.44
2.50 7.37
2.56 7.99
2.56 8.05
2.56 8.05
2.56 8.05
3.00 9.31
3.00 9.31
3.00 9.31
3.00 9.31
3.25 9.94
3.25 10.06
3.25 9.94
3.25 9.94
3.25 10.06
3.25 10.43
3.25 10.56
3.25 10.43
3.25 10.56
3.25 10.56
Style TT
ER
ZF
4.50
5.00
5.94
6.06
6.44
6.69
6.56
7.44
7.63
7.56
8.06
8.19
8.12
8.87
8.93
8.93
8.93
10.31
10.31
10.31
10.31
10.94
11.06
10.94
10.94
11.06
11.56
11.68
11.56
11.68
11.68
0.83
0.83
1.12
1.12
1.31
1.31
1.31
1.68
1.68
1.68
1.44
1.44
1.44
1.79
1.79
1.79
1.79
2.36
2.36
2.36
2.36
2.67
2.67
2.67
2.67
2.67
2.96
2.96
2.96
2.96
2.96
LB
3.69
4.06
4.94
4.94
5.38
5.38
5.38
6.13
6.13
6.13
6.50
6.50
6.50
7.12
7.12
7.12
7.12
8.37
8.37
8.37
8.37
9.00
9.00
9.00
9.00
9.00
9.50
9.50
9.50
9.50
9.50
Add Stroke
P
XC ZC
1.32 4.87 5.50
1.32 5.38 6.00
2.06 6.25 6.88
2.06 6.37 7.00
2.00 6.81 7.56
2.00 7.06 7.81
2.00 6.94 7.69
2.19 7.87 8.81
2.19 8.06 9.00
2.19 8.00 8.94
2.50 8.44 9.44
2.50 8.56 9.56
2.50 8.50 9.50
2.56 9.49 10.87
2.56 9.55 10.93
2.56 9.55 10.93
2.56 9.55 10.93
3.00 10.93 12.43
3.00 10.93 12.43
3.00 10.93 12.43
3.00 10.93 12.43
3.25 11.94 13.81
3.25 12.06 13.94
3.25 11.94 13.81
3.25 11.94 13.81
3.25 12.06 13.94
3.25 12.56 14.56
3.25 12.68 14.68
3.25 12.56 14.56
3.25 12.68 14.68
3.25 12.68 14.68
49


Switch on K-Type Both Ends

EN
EN
HS
HS
Styles KT & KDD
PK + STROKE
LD + STROKE
ZM + STROKE
EJ
EN
HS
HS
Styles KJ/KJP1
PK + STROKE
LJ + STROKE
ZN + STROKE
YF
Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
Styles KT, KDD & KJ / KJP

EN
HS
CLS-A EPS-A CLS-A EPS-A

1.63
1.63
4.49
2.66
2.01
2.01
4.49
2.66
2.31
2.20
4.25
2.91
2.31
2.20
4.25
2.91
2.56
2.45
4.47
3.13
2.56
2.45
4.47
3.13
2.56
2.45
4.47
3.13
2.81
2.70
4.84
3.51
2.81
2.70
4.84
3.51
2.81
2.70
4.84
3.51
3.06
2.95
5.15
3.82
3.06
2.95
5.15
3.82
3.06
2.95
5.15
3.82
3.31
3.20
5.59
4.26
3.31
3.20
5.59
4.26
3.31
3.20
5.59
4.26
3.31
3.20
5.59
4.26
3.19
3.14
6.09
4.76
3.19
3.14
6.09
4.76
3.19
3.14
6.09
4.76
3.19
3.14
6.09
4.76
3.20
3.08
6.59
5.26
3.20
3.08
6.59
5.26
3.20
3.08
6.59
5.26
3.20
3.08
6.59
5.26
3.20
3.08
6.59
5.26
3.41
3.29
7.09
5.76
3.41
3.29
7.09
5.76
3.41
3.29
7.09
5.76
3.41
3.29
7.09
5.76
3.41
3.29
7.09
5.76
Style KT
& KDD
Add Stroke
PK
1.91
1.91
3.26
3.26
3.40
3.40
3.40
3.53
3.53
3.53
3.86
3.86
3.86
4.00
4.00
4.00
4.00
2.92
2.92
2.92
2.92
3.16
3.16
3.16
3.16
3.16
3.21
3.21
3.21
3.21
3.21
LD
5.03
5.78
6.90
6.90
7.40
7.40
7.40
8.03
8.03
8.03
8.78
8.78
8.78
9.40
9.40
9.40
9.40
9.28
9.28
9.28
9.28
9.54
9.54
9.54
9.54
9.54
9.96
9.96
9.96
9.96
9.96
Styles KJ / KJP
ZM
EJ
YF
LJ
ZN
6.10
7.10
7.66
7.90
8.16
8.66
8.40
9.03
9.41
9.28
9.91
10.15
10.03
10.66
10.78
10.78
10.78
11.28
11.28
11.28
11.28
11.67
11.92
11.67
11.67
11.92
12.09
12.34
12.09
12.34
12.34
CLS-A EPS-A
2.01
2.01
2.01
2.01
2.44
2.33
2.44
2.33
2.69
2.58
2.69
2.58
2.69
2.58
2.94
2.83
2.94
2.83
2.94
2.83
3.06
2.95
3.06
2.95
3.06
2.95
3.25
3.14
3.25
3.14
3.25
3.14
3.25
3.14
3.56
3.51
3.56
3.51
3.56
3.51
3.56
3.51
3.82
3.70
3.82
3.70
3.82
3.70
3.82
3.70
3.82
3.70
3.91
3.79
3.91
3.79
3.91
3.79
3.91
3.79
3.91
3.79
2.75
3.25
3.26
3.38
3.44
3.69
3.56
3.81
4.00
3.94
4.15
4.27
4.21
4.45
4.51
4.51
4.51
4.99
4.99
4.99
4.99
5.25
5.38
5.25
5.25
5.38
5.44
5.56
5.44
5.56
5.56
5.40
5.78
7.03
7.03
7.53
7.53
7.53
8.15
8.15
8.15
8.78
8.78
8.78
9.34
9.34
9.34
9.34
9.65
9.65
9.65
9.65
10.16
10.16
10.16
10.16
10.16
10.46
10.46
10.46
10.46
10.46
6.73
7.73
8.03
8.28
8.53
9.03
8.78
9.40
9.78
9.66
10.16
10.40
10.28
10.91
11.03
11.03
11.03
12.03
12.03
12.03
12.03
12.67
12.92
12.67
12.67
12.92
13.09
13.34
13.09
13.34
13.34
See port and switch position note on mounting Styles J/JP dimension page.
50


Switch on K-Type End 1 Only

EN
HS
PK + STROKE
LD + STROKE
ZM + STROKE
Styles KT & KDD

EJ
HS
Styles KJ/KJP1
YF
PK + STROKE
LJ + STROKE
ZN + STROKE
Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
Styles KT, KDD &

KJ / KJP
Styles KT
& KDD
HS
Add Stroke
EN
CLS-A EPS-A
4.49
2.66
4.49
2.66
4.25
2.91
4.25
2.91
4.47
3.13
4.47
3.13
4.47
3.13
4.84
3.51
4.84
3.51
4.84
3.51
5.15
3.82
5.15
3.82
5.15
3.82
5.59
4.26
5.59
4.26
5.59
4.26
5.59
4.26
6.09
4.76
6.09
4.76
6.09
4.76
6.09
4.76
6.59
5.26
6.59
5.26
6.59
5.26
6.59
5.26
6.59
5.26
7.09
5.76
7.09
5.76
7.09
5.76
7.09
5.76
7.09
5.76
PK
1.72
1.72
2.51
2.51
2.65
2.65
2.65
2.78
2.78
2.78
3.11
3.11
3.11
3.25
3.25
3.25
3.25
2.79
2.79
2.79
2.79
3.16
3.16
3.16
3.16
3.16
3.21
3.21
3.21
3.21
3.21
CLS-A EPS-A
1.63
1.63
2.01
2.01
2.31
2.20
2.31
2.20
2.56
2.45
2.56
2.45
2.56
2.45
2.81
2.70
2.81
2.70
2.81
2.70
3.06
2.95
3.06
2.95
3.06
2.95
3.31
3.20
3.31
3.20
3.31
3.20
3.31
3.20
3.19
3.14
3.19
3.14
3.19
3.14
3.19
3.14
3.20
3.08
3.20
3.08
3.20
3.08
3.20
3.08
3.20
3.08
3.41
3.29
3.41
3.29
3.41
3.29
3.41
3.29
3.41
3.29
LD
4.84
5.59
6.15
6.15
6.65
6.65
6.65
7.28
7.28
7.28
8.03
8.03
8.03
8.65
8.65
8.65
8.65
9.15
9.15
9.15
9.15
9.54
9.54
9.54
9.54
9.54
9.96
9.96
9.96
9.96
9.96
Styles KJ / KJP
ZM
EJ
YF
LJ
ZN
5.98
6.98
7.53
7.78
8.03
8.53
8.28
8.90
9.28
9.16
9.91
10.15
10.03
10.66
10.78
10.78
10.78
11.28
11.28
11.28
11.28
11.67
11.92
11.67
11.67
11.92
12.09
12.34
12.09
12.34
12.34
CLS-A EPS-A
2.01
2.01
2.01
2.01
2.44
2.33
2.44
2.33
2.69
2.58
2.69
2.58
2.69
2.58
2.94
2.83
2.94
2.83
2.94
2.83
3.06
2.95
3.06
2.95
3.06
2.95
3.25
3.14
3.25
3.14
3.25
3.14
3.25
3.14
3.56
3.51
3.56
3.51
3.56
3.51
3.56
3.51
3.82
3.70
3.82
3.70
3.82
3.70
3.82
3.70
3.70
3.82
3.91
3.79
3.91
3.79
3.91
3.79
3.91
3.79
3.91
3.79
2.75
3.25
3.26
3.38
3.44
3.69
3.56
3.81
4.00
3.94
4.15
4.27
4.21
4.45
4.51
4.51
4.51
4.99
4.99
4.99
4.99
5.25
5.38
5.25
5.25
5.38
5.44
5.56
5.44
5.56
5.56
5.21
5.59
6.28
6.28
6.78
6.78
6.78
7.40
7.40
7.40
8.03
8.03
8.03
8.59
8.59
8.59
8.59
9.53
9.53
9.53
9.53
10.16
10.16
10.16
10.16
10.16
10.46
10.46
10.46
10.46
10.46
6.60
7.60
7.91
8.15
8.41
8.91
8.65
9.28
9.66
9.53
10.16
10.40
10.28
10.91
11.03
11.03
11.03
12.03
12.03
12.03
12.03
12.67
12.92
12.67
12.67
12.92
13.09
13.34
13.09
13.34
13.34
See port and switch position note on mounting Style J dimension page.
51


Switch on K-Type End 2 Only
EN
HS
Styles KT & KDD

PK + STROKE
LD + STROKE
ZM + STROKE
EN
HS
Styles KJ/KJP1
YF
Rod
No.
1 (std)
2
1 (std)
2
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
1 (std)
2
3
4
1 (std)
2
3
4
1 (std)
2
3
4
5
1 (std)
2
3
4
5
1
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
PK + STROKE
LJ + STROKE
ZN + STROKE
Styles KT, KDD & KJ / KJP

EN
CLS-A
1.63
2.01
2.31
2.31
2.56
2.56
2.56
2.81
2.81
2.81
3.06
3.06
3.06
3.31
3.31
3.31
3.31
3.19
3.19
3.19
3.19
3.20
3.20
3.20
3.20
3.20
3.41
3.41
3.41
3.41
3.41
EPS-A
1.63
2.01
2.20
2.20
2.45
2.45
2.45
2.70
2.70
2.70
2.95
2.95
2.95
3.20
3.20
3.20
3.20
3.14
3.14
3.14
3.14
3.08
3.08
3.08
3.08
3.08
3.29
3.29
3.29
3.29
3.29
HS
CLS-A
4.49
4.49
4.25
4.25
4.47
4.47
4.47
4.84
4.84
4.84
5.15
5.15
5.15
5.59
5.59
5.59
5.59
6.09
6.09
6.09
6.09
6.59
6.59
6.59
6.59
6.59
7.09
7.09
7.09
7.09
7.09
Styles KT
& KDD
Add Stroke
EPS-A
2.66
2.66
2.91
2.91
3.13
3.13
3.13
3.51
3.51
3.51
3.82
3.82
3.82
4.26
4.26
4.26
4.26
4.76
4.76
4.76
4.76
5.26
5.26
5.26
5.26
5.26
5.76
5.76
5.76
5.76
5.76
PK
1.41
1.41
2.51
2.51
2.65
2.65
2.65
2.78
2.78
2.78
3.11
3.11
3.11
3.25
3.25
3.25
3.25
2.92
2.92
2.92
2.92
3.16
3.16
3.16
3.16
3.16
3.21
3.21
3.21
3.21
3.21
LD
4.53
5.28
6.15
6.15
6.65
6.65
6.65
7.28
7.28
7.28
8.03
8.03
8.03
8.65
8.65
8.65
8.65
9.28
9.28
9.28
9.28
9.54
9.54
9.54
9.54
9.54
9.96
9.96
9.96
9.96
9.96
ZM
5.60
6.60
6.91
7.15
7.41
7.91
7.65
8.28
8.66
8.53
9.16
9.40
9.28
9.91
10.03
10.03
10.03
11.28
11.28
11.28
11.28
11.67
11.92
11.67
11.67
11.92
12.09
12.34
12.09
12.34
12.34
Styles KJ / KJP
YF
2.75
3.25
3.26
3.38
3.44
3.69
3.56
3.81
4.00
3.94
4.15
4.27
4.21
4.45
4.51
4.51
4.51
4.99
4.99
4.99
4.99
5.25
5.38
5.25
5.25
5.38
5.44
5.56
5.44
5.56
5.56
Add Stroke
LJ
4.90
5.28
6.65
6.65
7.15
7.15
7.15
7.78
7.78
7.78
8.53
8.53
8.53
9.09
9.09
9.09
9.09
9.65
9.65
9.65
9.65
10.16
10.16
10.16
10.16
10.16
10.46
10.46
10.46
10.46
10.46
ZN
6.23
7.23
7.66
7.90
8.16
8.66
8.40
9.03
9.41
9.28
9.91
10.15
10.03
10.66
10.78
10.78
10.78
12.03
12.03
12.03
12.03
12.67
12.92
12.67
12.67
12.92
13.09
13.34
13.09
13.34
13.34
See port and switch position note on mounting Style J dimension page.
52

Notes

Notes
53


Counterbalance Valves
Port Mounted Counterbalance Valves Add

Versatility to Series RDH Cylinders

V2
Offer hose break protection

Prevent loads from drifting
Control overrunning loads
Provide overcenter load control
Protect against pressure due to thermal expansion
C2
V1
C1
Counterbalance valves can be supplied for control of both

extend and retract stroke or only in one stroke direction.
The valve manifold can be installed on either the head end
or cap end. Carbon steel hydraulic tubing connects the
valve manifold to the opposite end port. A Lenz fitting in the
manifold port is plumbed to a matched SAE size zinc plated
Triple-Lok fitting in the cylinder port.
Single Counterbalance, Cap Mounted

V2
C2
V1
Many functional options are available to suit a wide

variety of applications:
C1
3 Valve Manifold sizes with 3 flow choices per size

3 standard pressure settings 1,000, 2,000
and 3,000 psi
4 standard pressure adjustment ranges
2 pilot ratios 3 to 1 or 4.5 to 1
Class 1 (standard) or Class 5 seals (contact the
factory for other seal classes)
Single Counterbalance, Head Mounted
V2
C2
Required information for selecting the correct

Counterbalance Valve for your application:
1. Oil flow through the port in GPM
2. System operating pressure in psi
3. Pressure (psi) to hold the load
4. Valve manifold location head or cap
5. Control of both extend and retract stroke or only in
one stroke direction
V1
C1
Note control of only one stroke direction affects the

required manifold location:
Manifold must be mounted at the cap end for
retract stroke control and load holding
Manifold must be mounted at the head end for
extend stroke control and load holding
Double Counterbalance, Cap Mounted
V2
C2
V1
C1
Double Counterbalance, Head Mounted
54


RDH Counterbalance Valve Manifold Assembly Ordering Code

Counterbalance Valves can be ordered on Series RDH cylinders as follows.
1) Complete the basic cylinder model number.
2) Place an 'S' in the model number to denote Special Modifications.
3) Specify the Counterbalance Valve Manifold option Ordering Code by making selections
from the categories below.
A C CA H
N A - 3000 / 2500
Valve Manifold Size

A SAE 6 Port - 5 GPM1
B SAE 8 Port - 10 GPM1
C SAE 12 Port - 20 GPM1
D SAE 16 Port - 40 GPM1
Single or Double Valve
S Single Control in one direction
D Double Control in both directions
Valve Manifold Material
A Aluminum
D Ductile Iron
Cap End or Head End Mounted
C Cap End Mounted
H Head End Mounted
Counterbalance Valve Capacity & Pilot Ratio
See Table A
Pressure Range
Valves with 3 to 1 Pilot Ratio
H 1000 to 4000 psi (3000 psi std. setting)
I 400 to 1500 psi (1000 psi std. setting)
Valves with 4.5 to 1 Pilot Ratio
J 2000 to 5000 psi (3000 psi std. setting)
K 1000 to 2500 psi (2000 psi std. setting)
Seals
N NBR - Nitrile
V FKM - Fluorocarbon
Valve Adjustment
A Screw Adjust (Std)
T with Tamper Resist Cover
Pressure Setting
Single Valve Manifold pressure setting of counterbalance valve (psi)
or
Double Valve Manifold pressure setting of counterbalance valve on C1 port (psi)
Pressure Setting C2 Port (Double Valve Manifold Only)
Double Valve Manifold - pressure setting of counterbalance valve on C2 port (psi)
Nominal flow for port size at 25 fps velocity.

1
Table A Counterbalance Valve Capacity & Pilot Ratio

Counterbalance
Valve Capacity
Standard
Standard
Semi-Restrictive
Semi-Restrictive
Restrictive
Restrictive
Valve Manifold Size A
Valve Manifold Size B
Valve Manifold Sizes C & D
Rated Max.
Flow (GPM)
Pilot
Ratio
Order
Code
Rated Max.
Flow (GPM)
Pilot
Ratio
Order
Code
Rated Max.
Flow (GPM)
Pilot
Ratio
Order
Code
15
15
10
10
5
5
3:1
4.5:1
3:1
4.5:1
3:1
4.5:1
CA
CG
BC
BD
BA
BG
30
30
20
20
8
8
3:1
4.5:1
3:1
4.5:1
3:1
4.5:1
EA
EG
DC
DD
DA
DG
60
60
40
40
15
15
3:1
4.5:1
3:1
4.5:1
3:1
4.5:1
GA
GG
FC
FD
FA
FG
55


Counterbalance Valve Control of One Stroke

Direction Only Dimensions
ML
MH
RV
BC
BC
EE (V2 - RETRACT)
HP
MW
RH
MO
CP
RV
ML
EE (V1 - EXTEND)
EH
MT
MC
FH
HF
Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod Manifold Min. BC

No.
Size Stroke
1
A
5.50 1.00
2
A
5.50 1.00
A
4.95 1.00
All
B
5.86 1.21
A
5.00 1.00
All
B
5.92 1.21
A
4.81 1.00
B
5.73 1.21
All
C
7.63 1.43
D
8.28 1.43
A
4.38 1.00
B
5.29 1.21
All
C
7.19 1.43
D
7.84 1.43
A
4.31 1.00
B
5.23 1.21
All
C
7.13 1.43
D
7.78 1.43
A
3.87 1.00
B
4.79 1.21
All
C
6.69 1.43
D
7.34 1.43
A
3.63 1.00
B
4.54 1.21
All
C
6.44 1.43
D
7.09 1.43
A
3.63 1.00
B
4.54 1.21
All
C
6.44 1.43
D
7.09 1.43
CP
0.96
0.96
0.96
1.16
0.96
1.16
0.96
1.16
1.68
1.53
0.96
1.16
1.68
1.53
0.96
1.16
1.68
1.53
0.96
1.16
1.68
1.53
0.96
1.16
1.68
1.53
0.96
1.16
1.68
1.53
EE
SAE
6
6
6
8
6
8
6
8
12
16
6
8
12
16
6
8
12
16
6
8
12
16
6
8
12
16
6
8
12
16
EH
FH
HF
0.59
0.59
0.59
0.71
0.59
0.71
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
1.79
1.79
2.04
2.12
2.37
2.43
2.81
2.81
3.18
3.18
3.17
3.19
3.57
3.57
3.75
3.80
4.17
4.17
4.37
4.42
4.80
4.80
4.87
4.92
5.30
5.30
5.50
5.55
5.92
5.92
3.00
3.00
3.39
3.52
3.73
3.84
4.16
4.21
4.82
5.07
4.53
4.60
5.20
5.46
5.10
5.20
5.81
6.06
5.73
5.83
6.43
6.69
6.23
6.33
6.93
7.19
6.85
6.95
7.56
7.81
HP
MC1
MH
ML
MO
MT
MW
RH
RV
0.22 -0.19 0.56

0.22 -0.19 0.94
0.22 0.06 0.82
0.28 -0.15 0.61
0.22 0.38 1.00
0.28 0.17 0.79
0.22 0.69 1.25
0.28 0.48 1.04
0.50 0.26 0.82
0.66 0.26 0.82
0.22 0.54 1.46
0.28 0.33 1.25
0.50 0.11 1.03
0.66 0.11 1.03
0.22 0.86 1.70
0.28 0.65 1.49
0.50 0.43 1.27
0.66 0.43 1.27
0.22 1.19 2.18
0.28 0.98 1.97
0.50 0.76 1.75
0.66 0.76 1.75
0.22 1.56 2.19
0.28 1.35 1.98
0.50 1.13 1.76
0.66 1.13 1.76
0.22 1.87 2.38
0.28 1.66 2.17
0.50 1.44 1.95
0.66 1.44 1.95
3.75
3.75
3.75
4.25
3.75
4.25
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
1.46
1.46
1.46
1.78
1.46
1.78
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.18
1.18
1.18
1.43
1.18
1.43
1.18
1.43
2.18
2.18
1.18
1.43
2.18
2.18
1.18
1.43
2.18
2.18
1.18
1.43
2.18
2.18
1.18
1.43
2.18
2.18
1.18
1.43
2.18
2.18
2.50
2.50
2.50
3.00
2.50
3.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
0.59
0.59
0.59
0.71
0.59
0.71
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
0.59
0.71
1.09
1.09
1.27
1.27
1.27
1.63
1.27
1.63
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
Negative values indicate valve block extension beyond rear of cap. Check rear mounting styles (especially pivot mounts) for possible
interference with a cap mounted manifold.
1
56


Counterbalance Valve Control of Both Extend

and Retract Strokes Dimensions
CV
MH
ML
BC
RV
RV
ML
CV
BC
RH
EE (V2 - RETRACT)
HP
MW
MO
CP
EE (V1 - EXTEND)
EH
MT
FH
MC
HF
Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod Manifold Min. BC CP

No.
Size Stroke
1
A
5.50 1.00 0.96
2
A
5.50 1.00 0.96
A
4.95 1.00 0.96
All
B
5.86 1.21 1.16
A
5.00 1.00 0.96
All
B
5.92 1.21 1.16
A
4.81 1.00 0.96
B
5.73 1.21 1.16
All
C
7.63 1.43 1.68
D
8.28 1.43 1.53
A
4.38 1.00 0.96
B
5.29 1.21 1.16
All
C
7.19 1.43 1.68
D
7.84 1.43 1.53
A
4.31 1.00 0.96
B
5.23 1.21 1.16
All
C
7.13 1.43 1.68
D
7.78 1.43 1.53
A
3.87 1.00 0.96
B
4.79 1.21 1.16
All
C
6.69 1.43 1.68
D
7.34 1.43 1.53
A
3.63 1.00 0.96
B
4.54 1.21 1.16
All
C
6.44 1.43 1.68
D
7.09 1.43 1.53
A
3.63 1.00 0.96
B
4.54 1.21 1.16
All
C
6.44 1.43 1.68
D
7.09 1.43 1.53
CV
1.28
1.28
1.28
1.32
1.28
1.32
1.28
1.32
1.69
1.69
1.28
1.32
1.69
1.69
1.28
1.32
1.69
1.69
1.28
1.32
1.69
1.69
1.28
1.32
1.69
1.69
1.28
1.32
1.69
1.69
EE
SAE
6
6
6
8
6
8
6
8
12
16
6
8
12
16
6
8
12
16
6
8
12
16
6
8
12
16
6
8
12
16
EH
FH
HF
HP
MC1
MH
ML
MO
MT
MW
RH
RV
0.59
0.59
0.59
0.81
0.59
0.81
0.59
0.81
1.43
1.93
0.59
0.81
1.43
1.93
0.59
0.81
1.43
1.93
0.59
0.81
1.43
1.93
0.59
0.81
1.43
1.93
0.59
0.81
1.43
1.93
1.79
1.79
2.04
2.12
2.37
2.43
2.81
2.81
3.18
3.18
3.17
3.19
3.57
3.57
3.75
3.80
4.17
4.17
4.37
4.42
4.80
4.80
4.87
4.92
5.30
5.30
5.50
5.55
5.92
5.92
3.00
3.00
3.39
3.52
3.73
3.84
4.16
4.21
4.82
5.07
4.53
4.60
5.20
5.46
5.10
5.20
5.81
6.06
5.73
5.83
6.43
6.69
6.23
6.33
6.93
7.19
6.85
6.95
7.56
7.81
0.25
0.25
0.25
0.22
0.25
0.22
0.25
0.22
0.00
0.35
0.25
0.22
0.00
0.35
0.25
0.22
0.00
0.35
0.25
0.22
0.00
0.35
0.25
0.22
0.00
0.35
0.25
0.22
0.00
0.35
-0.19
-0.19
0.06
-0.15
0.38
0.17
0.69
0.48
0.26
0.26
0.54
0.33
0.11
0.11
0.86
0.65
0.43
0.43
1.19
0.98
0.76
0.76
1.56
1.35
1.13
1.13
1.87
1.66
1.44
1.44
1.56
1.94
1.82
1.82
2.00
2.00
2.25
2.25
2.25
2.25
2.46
2.46
2.46
2.46
2.70
2.70
2.70
2.70
3.18
3.18
3.18
3.18
3.19
3.19
3.19
3.19
3.38
3.38
3.38
3.38
3.75
3.75
3.75
4.25
3.75
4.25
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
3.75
4.25
5.46
5.46
1.46
1.46
1.46
1.78
1.46
1.78
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
1.46
1.78
2.43
2.43
2.18
2.18
2.18
2.75
2.18
2.75
2.18
2.75
3.93
3.93
2.18
2.75
3.93
3.93
2.18
2.75
3.93
3.93
2.18
2.75
3.93
3.93
2.18
2.75
3.93
3.93
2.18
2.75
3.93
3.93
2.50
2.50
2.50
3.00
2.50
3.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
2.50
3.00
4.00
4.00
0.50
0.50
0.50
0.62
0.50
0.62
0.50
0.62
1.18
1.09
0.50
0.62
1.18
1.09
0.50
0.62
1.18
1.09
0.50
0.62
1.18
1.09
0.50
0.62
1.18
1.09
0.50
0.62
1.18
1.09
1.27
1.27
1.27
1.63
1.27
1.63
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
1.27
1.63
1.69
1.69
Negative values indicate valve block extension beyond rear of cap. Check rear mounting styles (especially pivot mounts) for possible
interference with a cap mounted manifold.
1
57

Notes

Notes
58

Notes

Notes
59


Engineering Data
Theoretical Push and Pull Forces
Theoretical Push Forces for Cylinders

Cylinder
Bore
Piston Area
(In.2)
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
1.77
3.14
4.91
8.30
12.57
19.64
28.27
38.49
50.27
Cylinder Push Stroke Force in Pounds at Various Pressures (psi)

100
250
500
1000
1500
2000
3000
177
314
491
830
1257
1964
2827
3849
5027
443
785
1228
2075
3143
4910
7068
9623
12568
885
1570
2455
4150
6285
9820
14135
19245
25135
1770
3140
4910
8300
12570
19640
28270
38490
50270
2651
4712
7363
12444
18850
29453
42412
57727
75398
3540
6280
9820
16600
25140
39280
56540
76980
100540
5310
9420
14730
24900
37710
58920
84810
115470
150810
General Formula

Where F = Force in pounds.

P = Pressure at the cylinder in
pounds per square inch, gauge.

A = Effective area of cylinder piston
in square inches.
The cylinder output forces are derived from the formula:

F = P x A
Theoretical Pull Forces for Cylinders

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Cylinder Pull Force in Pounds at Various Pressures (psi)
Piston
Rod
Piston
Rod Area
(In.2)
100
250
500
1000
1500
2000
3000
0.625
1.000
1.000
1.375
1.000
1.375
1.750
1.375
1.750
2.000
1.750
2.000
2.500
2.000
2.500
3.000
3.500
2.500
3.000
3.500
4.000
3.000
3.500
4.000
4.500
5.000
3.500
4.000
4.500
5.000
5.500
0.307
0.785
0.785
1.48
0.785
1.48
2.41
1.48
2.41
3.14
2.41
3.14
4.91
3.14
4.91
7.07
9.62
4.91
7.07
9.62
12.57
7.07
9.62
12.57
15.90
19.63
9.62
12.57
15.90
19.63
23.76
146
98
236
166
413
343
250
682
589
516
1016
943
766
1650
1473
1257
1002
2336
2120
1865
1570
3142
2887
2592
2259
1886
4065
3770
3437
3064
2651
365
245
589
414
1031
856
625
1704
1473
1290
2540
2358
1915
4125
3683
3143
2505
5840
5300
4663
3925
7855
7218
6480
5648
4715
10163
9425
8593
7660
6628
730
491
1178
828
2063
1713
1250
3408
2945
2580
5080
4715
3830
8250
7365
6285
5010
11680
10600
9325
7850
15710
14435
12960
11295
9430
20325
18850
17185
15320
13255
1460
982
2355
1655
4125
3425
2500
6815
5890
5160
10160
9430
7660
16500
14730
12570
10020
23360
21200
18650
15700
31420
28870
25920
22590
18860
40650
37700
34370
30640
26510
2190
1473
3533
2483
6188
5138
3750
10223
8835
7740
15240
14145
11490
24750
22095
18855
15030
35040
31800
27975
23550
47130
43305
38880
33885
28290
60975
56550
51555
45960
39765
2920
1964
4710
3310
8250
6850
5000
13630
11780
10320
20320
18860
15320
33000
29460
25140
20040
46720
42400
37300
31400
62840
57740
51840
45180
37720
81300
75400
68740
61280
53020
4380
2946
7065
4965
12375
10275
7500
20445
17670
15480
30480
28290
22980
49500
44190
37710
30060
70080
63600
55950
47100
94260
86610
77760
67770
56580
121950
113100
103110
91920
79530
60


Engineering Data
Cylinder Weights
Cylinder Weights
The estimated weights shown below are for standard
Series RDH hydraulic cylinders equipped with the
different piston rod diameters. To determine the total
net weight of a cylinder, first select the Basic Weight
for the proper mount at zero stroke, then calculate the

weight of the cylinder stroke and add the result to the
Basic Weight. For extra rod extension, use piston rod
weight per inch shown in Table B.
Table A Series RDH Cylinder Weights in pounds.

Bore
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
Rod
No.
1
2
1
2
1
2
3
1
2
3
1
2
3
1
2
3
4
1
2
3
4
1
2
3
4
5
1
2
3
4
5
MM
Rod
0.625
1.000
1.000
1.375
1.000
1.750
1.375
1.375
2.000
1.750
1.750
2.500
2.000
2.000
3.500
2.500
3.000
2.500
4.000
3.000
3.500
3.000
5.000
3.500
4.000
4.500
3.500
5.500
4.000
4.500
5.000
Single Rod Cylinders

Base Weight at Zero Stroke
T
B, BB, SB/SBM, TT
DD
J/JP
2.5
2.7
5.0
5.4
8.8
9.4
9.8
16.5
17.2
17.8
22.3
24.0
24.7
51.2
52.9
54.6
56.8
75.7
79.7
81.9
83.6
111.8
116.1
118.0
122.0
126.1
159.6
166.9
171.4
175.5
179.8
3.7
3.9
6.6
7.0
11.3
11.9
12.3
22.5
23.2
23.8
28.3
30.0
30.7
57.2
58.9
60.6
62.8
83.7
87.7
89.9
91.6
124.8
129.1
131.0
135.0
139.1
173.6
180.9
185.4
189.5
193.8
5.6
5.8
9.7
10.1
13.7
14.3
14.7
24.9
25.6
26.2
31.4
33.1
33.8
67.7
69.4
71.1
73.3
102.8
106.8
109.0
110.7
154.0
158.3
160.2
164.2
168.3
217.4
224.7
229.2
233.3
237.6
3.8
4.0
7.3
7.7
12.5
13.2
13.6
23.6
24.2
24.8
34.4
36.1
36.7
69.8
71.5
73.2
75.4
106.5
110.5
112.7
114.4
151.8
156.1
158.0
162.0
166.1
216.7
224.0
228.5
232.6
236.9
3.4
3.6
6.4
6.8
11.3
12.0
12.3
21.7
22.4
23.0
31.4
33.1
33.8
66.0
67.7
69.4
71.6
100.9
104.9
107.2
108.8
141.7
146.0
147.9
151.9
156.0
204.5
211.8
216.3
220.4
224.7
Add
per Inch
of Stroke
0.4
1.0
0.6
1.7
0.8
2.7
2.4
1.4
4.2
4.0
1.8
6.1
5.6
2.7
10.1
8.7
9.3
4.3
14.4
12.9
13.6
5.3
19.8
16.9
17.8
18.7
7.5
25.7
22.6
23.5
24.6
Table B Extra weight for longer than standard rod extensions

Rod
Piston Rod Weight

per Inch (lb)
Rod
Piston Rod Weight

per Inch (lb)
0.625
0.09
3.000
2.00
1.000
0.22
3.500
2.72
1.375
0.42
4.000
3.56
1.750
0.68
4.500
4.50
2.000
0.89
5.000
5.56
2.500
1.39
5.500
6.72
61


Engineering Data
Seal Information
and dynamic applications. They are intended for high temperature applications, to 400F (204C), where longer seal life and
improved high temperature sealing performance is required.
End seal and energizer o-ring seals will be fluorocarbon. Fluid
resistance is comparable to Class 5. Cylinders incorporating
Class 8 Seals will not have studded piston rods.
Operating Fluids and Temperature Range

Fluidpower cylinders are designed for use with pressurized
air, hydraulic oil and fire resistant fluids; in some cases special
seals are required.
Standard Seals (class 1)
Class 1 seals are what is normally provided in a cylinder
unless otherwise specified. They are intended for use with
fluids such as: air, nitrogen, mineral base hydraulic oil or
MIL-H-5606 within the temperature range of -10F (-23C) to
+165F (+74C). The individual seals may be nitrile (Buna-N),
enhanced polyurethane, polymyte, P.T.F.E. or filled P.T.F.E.
Water Base Fluid Seals (class 2)
Generally class 2 seals are intended for use with water base
fluids within the temperature of -10F (-23C) to +165F (+74C)
except for High Water Content Fluids (H.W.C.F.) in which case
Class 6 seals should be used. Typical water base fluids are:
Water, Water-Glycol, Water-in Emulsion, Houghto-Safe 27,
620, 5040, Mobil Pyrogard D, Shell Irus 905, Ucon Hydrolube
J-4. These seals are nitrile. Rod seal and piston seal will have
polymyte or P.T.F.E. back-up washer when required. Piston
seal may be filled P.T.F.E. O-rings will have nitrile back-up
washers when required.
Ethylene Propylene (E.P.R.) Seals (class 3)
Class 3 seals are intended for use with some Phosphate Ester
Fluids between the temperatures of -10F (-23C) to +130F
(+54C). Typical fluids compatible with E.P.R. seals are Skydrol
500 and 700. E.P.R. are Ethylene Propylene. Rod seal and
piston seal will have a P.T.F.E. back-up washer when required.
Piston seal may be filled P.T.F.E. O-rings will have EPR
back-up washers when required. Note: E.P.R. seals are not
compatible with mineral base hydraulic oil or greases. Even
limited exposure to these fluids will cause severe swelling.
P.T.F.E. back-up washer may not be suitable when used in a
radiation environment.
Low Temperature Nitrile Seals (class 4)
Class 4 seals are intended for low temperature service with
the same type of fluids as used with Class 1 seals within the
temperature range of -50F (-46C) to +150F (+66C). Rod
seal and piston seal will have leather, polymyte or P.T.F.E.
back-up washers when required. Piston seal may be filled
P.T.F.E. O-rings will have nitrile back-up washers when
required. Note: Certain fluids may react adversely with Class 4
seals compared to Class 1 seals.
Fluorocarbon Seals (class 5)
Class 5 seals are intended for elevated temperature service or
for some Phosphate Ester Fluids such as Houghto-Safe 1010,
1055, 1120; Fyrquel 150, 220, 300, 350; Mobile Pyrogard 42,
43, 53, and 55. Note: In addition, class 5 seals can be used
with fluids listed on the next page under standard service.
However, they are not compatible with Phosphate Ester Fluids
such as Skydrols. Class 5 seals can operate with a temperature range of -10F (-23C) to +250F (+121C). Class 5 seals
may be operated to +400F (+204C) with limited service life.
For temperatures above +250F (+121C) the cylinder must be
manufactured with non-studded piston rod and thread and a
pinned piston to rod connection. Class 5 rod seal and piston
seal will have P.T.F.E. back-up washers when required. Piston
seal may be filled P.T.F.E. O-rings will have fluorocarbon backup when required.
H.W.C.F. Seals (class 6)
Class 6 seals are intended for High Water Content Fluids
(H.W.C.F.) such as Houghton, Hydrolubric 120B and Sonsol
Lubrizol within the temperature range of +40F (+4C) to
+120F (+49C). Class 6 seals are the same as Class 2 seals.
Rod seal and piston seal will have P.T.F.E. and or polymyte
back-up washers when required. Piston seal may be filled
P.T.F.E. O-rings will have nitrile back-up washers when
required.
Energized PTFE Seals (class 8)
Class 8 seals consist of PTFE rod seals, rod wiper seal and
piston seal. All seals have o-ring energizers for sealing in static
Warning
The piston rod stud and the piston rod to piston threaded
connections are secured with an anaerobic adhesive which is
temperature sensitive. Cylinders are assembled with anaerobic
adhesive having a maximum temperature rating of +250F
(+121C). Cylinders specified with all other seal compounds
(built before 1997) were assembled with anaerobic adhesive
having a maximum operating temperature rating +165F
(+74C). These temperature limitations are necessary to
prevent the possible loosening of the threaded connections.
Cylinders originally manufactured (before 1997) with class 1
seals (Nitrile) that will be exposed to ambient temperatures
above +165F (+74C) must be modified for higher temperature
service. Contact the factory immediately and arrange for the
piston to rod and the stud to piston rod connections to be
properly re-assembled to withstand the higher temperature
service.
Hi-Load Seals
Hi-load seals consist of one PTFE dynamic piston seal with
an energizer underneath. Hi-load piston arrangement includes
a wear ring on the piston. The piston seal is virtually leak-free
under static conditions and can tolerate high pressure. The
wear ring on the piston can also tolerate high side loads. The
dynamic portion of the seal is bronze filled PTFE and compatible with all conditions and fluids listed on this page. However,
carbon filled PTFE will provide better seal life when used with
class 6 fluids. A nitrile expander will be provided unless Class
3 or 5 seals are specified. In those cases the expander will be
of E.P.R. or fluorocarbon respectively. Note: It may be necessary to cycle the piston seals 40 or 50 times before achieving
leakage free performance.
Low Friction Hydraulic Seals
Low friction hydraulic seals are available as an option. They
are sometimes used when a cylinder is controlled by a servo
valve or proportional valve. The rod seals, rod wiper seal and
piston seal are two-piece assemblies that include a filled
PTFE dynamic seal with an o-ring energizer. The piston and
head also include WearGard wear rings. The filled PTFE
seals are compatible with the fluids listed on this page and
provide virtually leak-free sealing. The energizers will be
fluorocarbon unless E.P.R. seals are specified. In those cases
the energizers will be E.P.R. Note: It may be necessary to
cycle these seals 40 or 50 times before achieving leakage
free performance.
Water Service
Series RDH cylinders can be modified to make them more
suitable for use with water as the operating medium. The
modifications include chrome-plated cylinder bore; electroless
nickel-plated head, cap and piston; and a chrome plated 17-4
stainless steel piston rod.
When high water base fluids are the operating medium,
hydraulic cylinders are usually supplied with high water base
rod wiper and seals. Water and high water base fluid operated
cylinders are best used on short stroke applications or where
high pressure is applied only to clamp the load.
Warranty
Parker Hannifin will warrant cylinders modified for water or high
water content fluid service to be free of defects in materials or
workmanship, but cannot accept responsibility of premature
failure due to excessive wear from lack of lubricity or where
failure is caused by corrosion, electrolysis or mineral deposits
within the cylinder.
62


Engineering Data
Seal Information
Fluids and Temperature Range

Class No.
Typical Fluids
Temperature Range
1 (Standard)
(Nitrile, Polyurethane)
Air, Nitrogen
Hydraulic Oil, Mil-H-5606 Oil
-10F (-23C) to
+165F (+74C)
2 Water Base Fluid Seal
Water, Water-Glycol, Water-in-Oil Emulsion

Houghto-Safe, 271, 620, 5040. Mobil Pyrogard D,
Shell Irus 905. Ucon Hydrolube J-4
-10F (-23C) to
+165F (+74C)
3 E.P.R.
Some Phosphate Ester Fluids

Skydrol 500, 7000
Note: (E.P.R.) seals are not compatible with Hydraulic Oil
-10F (-23C) to
+130F (+54C)
4 Nitrile
-50F (-46C) to
+150F (+66C)
Low Temperature Air or Hydraulic Oil
5 Fluorocarbon Seals
High Temperature
Houghto-Safe 1010, 1055, 1120
Fyrquel 150, 220, 300, 550
Mobil Pyrogard 42,43,53,55
Note: Fluorocarbon seals are not suitable for use with Skydrol fluid, but can be used with
hydraulic oil if desired.
See paragraph on
Fluorocarbon Seals on
previous page for
recommended temperature range.
6 HWCF (same seals as Class 2)
Houghton, Hydrolubric 120B

Sonsol Lubrizol; for other HWCF
consult factory.
+40F (+4C) to
+120F (+49C)
8 Energized PTFE
See Class 5 Seals
-15F (-26C) to
+400F (+204C)
Seal Compounds by Seal Code

Seal
Code
Description
Rod Wiper
Seal
Rod Seal
Rod Seal
Backup
Ring
Piston
Seal
(blank)
Standard
(Class 1)
Urethane
Polyurethane
N/A
Polyurethane
Nitrile
Fluoro
carbon
Nitrile
Nitrile
Composite
Water Base
Fluid/HWCF
(Classes
2 and 6)
Nitrile
Carboxylated
Nitrile
PTFE
Bronze
Filled
PTFE
Nitrile
Fluoro
carbon
Nitrile
Nitrile
Composite
EPR (Class 3)
EPR
EPR
PTFE
Bronze
Filled
PTFE
EPR
EPR
EPR
PTFE
Composite
Low
Temperature
(Class 4)
N/A
Polyurethane
Low
Temper
ature
Nitrile
Fluoro
carbon
Low
Temper
ature
Nitrile
Low
Temper Composite
ature
Nitrile
Fluorocarbon Fluorocarbon Fluorocarbon

(Class 5)
PTFE
Bronze
Filled
PTFE
Fluoro
carbon
Fluoro
carbon
Fluoro
carbon
Fluoro
carbon
Composite
Extreme High Bronze Filled Bronze Filled

PTFE with
PTFE with
Temperature Fluoro
c
arbon
Fluoro
carbon
(Class 8)
Energizer
Energizer
N/A
Bronze
Filled
PTFE
Fluoro
carbon
Fluoro
carbon
Fluoro
carbon
Fluoro
carbon
High
Temper
ature
Composite
Standard
(with Bronze
Filled PTFE
Piston Seal)
N/A
Bronze
Filled
PTFE
Nitrile
Fluoro
carbon
Nitrile
Nitrile
Composite
Fluorocarbon
Rod Seals Fluorocarbon Fluorocarbon
Only
PTFE
Polyurethane
Nitrile
Fluoro
carbon
Nitrile
Nitrile
Composite
N/A
Polyurethane
Nitrile
Fluoro
carbon
Nitrile
Nitrile
Composite
PTFE
Bronze
Filled
PTFE
Fluoro
carbon
Fluoro
carbon
Fluoro
carbon
Fluoro
carbon
Composite
Metallic
Rod Wiper,
Standard
Seals
Urethane
Urethane
Polyurethane
Polyurethane
Brass with
Fluorocarbon Polyurethane
Energizer
Metallic Rod
Brass with
Wiper, Fluoro Fluorocarbon Fluorocarbon
carbon Seals
Energizer
Piston
Piston End Seal End Seal
Seal
Joint Seal
Backup
Energizer
Ring
63
Wear
Rings


Engineering Data
Ports
Ports
International Ports
Other port configurations to meet international requirements are available for an additional charge. Series RDH
cylinders can be supplied with British standard taper
ports (BSPT). Such port has a taper of 1 in 16 measured
on the diameter (1/16" per inch). The thread form is
Whitworth System, and size and number of threads per
inch are as follows:
Series RDH cylinders can be supplied with many port

styles, but SAE straight o-ring ports are standard. Extra
ports are available for an additional charge.
Standard port location is position 1 as shown in the
mounting drawings and Figure 1 below. Port locations
other than position 1 can be specified for no additional
charge if both ports are in the same new position. If
either port is required to be at a different position than
the other, additional charges would apply.
Table B
British Standard Pipe Threads
Figure 1
1
Head (Rod) End
Head
Cap
Straight Thread Ports
The SAE straight thread o-ring port is recommended

for hydraulic applications. SAE port size numbers are
listed next to the NPTF pipe thread counterparts for
each bore size in the respective catalog pages. Size
number, tube O.D., and port thread size for SAE ports
are listed in Table A.
Tube
O.D. (in.)
Thread
Size
0.13
5/16 - 24
0.19
3/8 - 24
0.25
7/16 - 20
0.31
1/2 - 20
0.38
9/16 - 18
0.50
3/4 - 16
10
0.63
7/8 - 14
12
0.75
1 1/16 - 12
16
1.00
1 5/16 - 12
20
1.25
1 5/8 - 12
24
1.50
1 7/8 - 12
32
2.00
2 1/2 - 12
No. Threads
Per Inch
Pipe
O.D.
1/8
28
0.383
1/4
19
0.518
3/8
19
0.656
1/2
14
0.825
3/4
14
1.041
11
1.309
1 1/4
11
1.650
1 1/2
11
1.882
11
2.347
British standard parallel internal threads are designated

as BSPP and have the same thread form and number of
threads per inch as the BSPT type and can be supplied
for an additional charge. Unless otherwise specified,
the BSPP or BSPT port size supplied will be the same
nominal pipe size as the NPTF port for a given bore size
cylinder.
Table A
SAE Straight Thread O-Ring Ports
Size
No.
Nominal
Pipe Size
Note: For the pressure ratings of individual connectors,

contact your connector supplier. Hydraulic cylinders
applied with meter out or deceleration circuits are
subject to intensified pressure at the cylinder piston rod
end. The rod end pressure is approximately equal to:
Effective Cap End Piston Area
x Operating Pressure
Effective Rod End Piston Area
64


Engineering Data
Ports
SAE 4-Bolt Flange Ports

(Code 61, 3000 psi)
SAE 4-bolt flange port connections provide the ability to

connect larger pipe or hose sizes and achieve higherpressure capability at reasonable assembly torques.
Because of the lower assembly torques compared to
an equivalent size threaded port, SAE 4-bolt flange
ports are well suited for tight quarters where wrench
clearances are limited. See Table A for port mounting
flange dimensions and Table B for port flange height
dimensions.
A
HD
GG
F
Q B
EE
4X Z Thread
Table A
Table B
Flange SAE
Size Dash
No.
0.50
GG
1.81
2.13
0.69
1.50
0.63
EE
Bore
0.75
12
1.97
2.56
0.88
1.88
0.71
0.744
3/8-16
16
2.17
2.75
1.03
2.06
0.71
0.959
3/8-16
1.25
20
2.68
3.12
1.19
2.31
0.83
1.280 7/16-14
1.50
24
3.07
3.68
1.41
2.75
0.98
1.502
Code 61 Flange Size

0.50
0.548 5/16-18
1.00
HD
1/2-13
Undersize and Oversize Ports
0.75
1.00
1.25
1.50
1.50
N/A
N/A
N/A
N/A
N/A
2.00
2.52
N/A
N/A
N/A
N/A
2.50
2.85
N/A
N/A
N/A
N/A
3.25
3.29
3.29
3.37
N/A
N/A
N/A
4.00
3.65
3.65
3.73
N/A
5.00
4.23
4.23
4.31
N/A
N/A
6.00
4.85
4.85
4.93
5.04
N/A
7.00
5.35
5.35
5.43
5.54
5.66
8.00
5.98
5.98
6.06
6.17
6.29
Undersize and oversize ports are available. Please

consult factory.
Metric ports can also be supplied to order for an
additional charge. See table below for the standard port
size for each bore.
Table C Standard Port Sizes
Bore
U
NPTF
T
SAE
R
BSPP
B
BSPT
G
Metric
P
Flange
1.50
3/8
G3/8
Rc3/8
M18x1.5
NA
2.00
1/2
G1/2
Rc1/2
M22x1.5
0.50
2.50
1/2
G1/2
Rc1/2
M22x1.5
0.50
3.25
3/4
12
G3/4
Rc3/4
M27x2
0.75
4.00
3/4
12
G3/4
Rc3/4
M27x2
0.75
5.00
3/4
12
G3/4
Rc3/4
M27x2
0.75
6.00
16
G1
Rc1
M33x2
1.00
7.00
1 1/4
20
G1-1/4
Rc1-1/4
M42x2
1.25
8.00
1 1/4
20
G1-1/4
Rc1-1/4
M42x2
1.50
65


Engineering Data
Stroke Data and Mounting Groups

Stroke Data
Fatigue Life
Series RDH cylinders are available in any practical

stroke length.
Although each application is unique, all cylinders have

a finite life. In general, welded cylinders have a limited
fatigue life when used at the maximum pressure
rating. Series RDH cylinders are rated for industrialgrade service but for the maximum possible fatigue
life in severe duty applications, Parker cylinders with
another construction style (tie-rod, mill-type or bolted)
should be considered. If necessary, consult the factory
for assistance.
Stroke Length Tolerance
Stroke length tolerances are required due to buildup

of tolerances of the piston, head, cap and cylinder tube.
Standard stroke length tolerances are:

for strokes up to 43" = -0/+.040"
for strokes greater than 43" = -0/+.062"
Note: User Responsibility. The user, through its own

analysis and testing, is solely responsible for making the
final selection of the system and Product and assuring
that all performance, endurance, maintenance, safety
and warning requirements of the application are met.
The user must analyze all aspects of the application
and follow applicable industry standards and Product
information. If Seller provides Product or system
options, the user is responsible for determining that such
data and specifications are suitable and sufficient for
all applications and reasonably foreseeable uses of the
Products or systems.
For closer tolerances on stroke length, it is necessary

to specify the required tolerance plus the pressure and
temperature at which the cylinder will operate. Stroke
tolerances smaller than .015" are not generally practical
due to elasticity of cylinders. If machine design requires
such close tolerances, use of a stroke adjuster or special
endcap ties may achieve the desired result. Please
consult factory.
Mounting Groups
Standard mountings for Series RDH cylinders fall into
two basic groups. The groups can be summarized as
follows:
Straight Line Force Transfer fixed mounts which
absorb force on the cylinder centerline
Styles J/JP
Style H
Pivot Force Transfer mountings that permit a

cylinder to change its alignment in one plane
Style B
Style BB
Style SB/SBM
The cylinders mounting directly affects the maximum

pressure at which the cylinder can be used. Stroke
length, piston rod connection to load, extra piston rod
length over standard, etc. should be considered for
thrust loads. See Stop Tubing and Piston Rod Selection
Style TT
Style DD
Data on the following pages to first determine whether

stop tubing is recommended and then determine the
correct piston rod diameter for an application. Alloy
steel mounting bolts are recommended for all
mounting styles.
66


Engineering Data
Stop Tubing
Stop Tubing
2. Establish the Basic Length (L), with the piston rod

fully extended, for the selected illustration by using
the dimensional tables on previous pages of this
catalog. For pivot mounted cylinders, the pin-to-pin
dimension with the piston rod fully extended must
be used. Regardless of mounting style, be sure to
include any extended piston rod length beyond the
catalog standard.
3. In the Stop Tube Table select the column for the
appropriate mounting style and rod end guiding type.
In the Basic Length (L) column, find the row with
the range that includes the value calculated in Step
2. The next respective column to the right has the
required length of stop tube.
Note: Mounting Styles B, BB, SB/SBM, TT and H that
are mounted horizontally should also be checked for
turning moments and loads between the rod bearing
and piston to ensure they are not excessive. Weight of
oil must be included in determining bearing loads.
When specifying cylinders with stop tube be sure to
call out the net stroke and the length of the stop tube.
Machine design can be continued without delay by
laying in a cylinder equivalent in length to the NET
STROKE PLUS STOP TUBE LENGTH, which is
referred to as GROSS STROKE.
Cylinder Mounting and
Rod Guiding Groups
Stop tube is recommended to lengthen the distance

between the rod bearing and piston bearing to reduce
bearing loads on long push stroke cylinders when the
cylinder is fully extended. This is especially true of
horizontally mounted cylinders. As part of the piston
assembly and positioned between the piston and
head, a stop tube restricts the extended position of
the rod using the increased distance to achieve
additional stability.
STOP TUBE
NET STROKE
GROSS STROKE
STOP TUBE
LENGTH
Use the following steps to determine the need for stop

tube and, if required, how long it should be.
1. Examine the groups of cylinder illustrations below
and determine which mounting and rod guiding group
type match the required cylinder application.
Stop Tube Table
Pivot Mounts
(B, BB, SB/SBM,
TT and DD)
Pivoted and Rigidly
Guided Rod End
Basic
Stop
Length
Tube
(L)
Length
0
- 40
0
41 - 50
1
51 - 60
2
61 - 70
3
71 - 80
4
81 - 90
5
91 - 100
6
101 - 110
7
111 - 120
8
121 - 130
9
131 - 140
10
141 - 150
11
151 - 160
12
161 - 170
13
171 - 180
14
181 - 190
15
191 - 200
16
201 - 210
17
211 - 220
18
221 - 230
19
231 - 240
20
241 - 250
21
251 - 260
22
261 - 270
23
271 - 280
24
281 - 290
25
291 - 300
26
Consult Factory
Fixed Mounts (J/JP and H)
Fixed and Rigidly Pivoted and Rigidly

Unguided
Guided Rod End
Guided Rod End
Rod End
Basic
Stop
Basic
Stop
Basic
Stop
Length
Tube
Length
Tube
Length
Tube
(L)
Length
(L)
Length
(L)
Length
0 - 80
0
0 - 57
0
0 - 20
0
81 - 100 1
58 - 71
1
21 - 25
1
101 - 120 2
72 - 86
2
26 - 30
2
121 - 140 3
87 - 100 3
31 - 35
3
141 - 160 4 101 - 114 4
36 - 40
4
161 - 180 5 115 - 129 5
41 - 45
5
181 - 200 6 130 - 143 6
46 - 50
6
201 - 220 7 144 - 157 7
51 - 55
7
221 - 240 8 158 - 171 8
56 - 60
8
241 - 260 9 172 - 186 9
61 - 65
9
261 - 280 10 187 - 200 10 66 - 70 10
281 - 300 11 201 - 214 11 71 - 75 11
215 - 229 12 76 - 80 12
230 - 243 13 81 - 85 13
244 - 257 14 86 - 90 14
258 - 271 15 91 - 95 15
272 - 286 16 96 - 100 16
287 - 300 17 101 - 105 17
106 - 110 18
111 - 115 19
Consult Factory
116 - 120 20
121 - 125 21
126 - 130 22
Consult Factory
131 - 135 23
136 - 140 24
141 - 145 25
146 - 150 26
Consult Factory
67
Pivot Mount Pivoted and rigidly guided rod end

L
Styles B, BB,
SB/SBM and TT
Style DD
Fixed Mount Fixed and rigidly guided rod end
L
Styles J/JP
Style H
Fixed Mount Pivoted and rigidly guided rod end
L
Styles J/JP
Style H
Fixed Mount Unguided rod end
L
Styles J/JP
Style H


Engineering Data
Piston Rod Selection Data
Piston Rod Diameter Selection
Long stroke cylinders that work on push with the piston

rod loaded in compression should be checked, using
the following steps, to ensure an appropriate piston rod
diameter is specified.
1. First, determine whether stop tubing is required as
described on the previous page.
2. Use the Basic Length (L) that was established for
determining the stop tube length and then add the
required stop tube length to the Basic Length to
obtain an Adjusted Basic Length (LA).
3. In the table below, for the mounting style and rod end
guiding condition that will be used, find the row for the
Bore and Rod combination that is required.
4. Follow the Bore and Rod row to the right and find
the Operating Pressure column that is closest, but
exceeds the system pressure. The intersection of the

Bore and Rod row and Operating Pressure column
displays the maximum allowable LA. If LA in the table
is greater than or equal to the calculated LA, the rod
diameter selected is satisfactory for the application.
5. If LA in the table is less than the calculated Adjusted
Basic Length move down the column to a rod diameter with an LA that exceeds the requirement.
6. If the LA specifies a rod diameter in a larger bore
then restart the process of sizing the stop tube and
re-check the rod diameter. Contact the factory if LA
exceeds 300 inches.
Note: Data in these tables assume standard rod extension (W dimension) and standard rod end accessories.
If different, consult factory.
Maximum Basic Lengths (LA) (all dimensions in inches)

Bore Rod
Pivoted and Rigidly

Guided Rod End
Max. Allowable Basic
Length (LA) at psi:
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
0.625
1.000
1.000
1.375
1.000
1.375
1.750
1.375
1.750
2.000
1.750
2.000
2.500
2.000
2.500
3.000
3.500
2.500
3.000
3.500
4.000
3.000
3.500
4.000
4.500
5.000
3.500
4.000
4.500
5.000
5.500
Front Fixed Mount (J)
Rear Pivot Mounts

(B, BB, SB1, SBM and TT)
500
35
85
66
116
54
99
151
78
123
157
102
131
194
107
163
226
289
139
197
260
300
171
228
289
300
300
203
261
300
300
300
1000 1500 2000 2500 3000

25 20 18 16 14
60 49 42 38 35
47 38 33 29 27
82 67 58 52 47
38 31 27 24 22
70 57 49 44 40
106 87 75 67 61
55 45 39 35 32
87 71 62 55 50
111 90 78 70 64
72 59 51 45 41
92 75 65 58 53
137 112 97 87 79
76 62 53 48 44
115 94 82 73 67
160 130 113 101 92
204 167 145 129 118
98 80 70 62 57
139 114 98 88 80
184 150 130 116 106
231 188 163 146 133
121 99 85 76 70
161 132 114 102 93
204 167 145 129 118
249 203 176 157 144
293 239 207 185 169
144 117 102 91 83
185 151 131 117 107
229 187 162 145 132
274 224 194 174 158
300 261 226 202 185
Fixed and Rigidly

Guided Rod End
Length (LA) at psi:
500 1000 1500 2000 2500 3000
50 39 26 29 20 19
128 90 73 64 57 52
95 67 55 47 42 38
181 127 104 90 80 73
76 53 43 37 33 30
144 102 83 71 64 58
234 165 135 117 104 95
111 78 63 55 49 44
180 127 103 89 80 72
235 166 135 117 105 95
146 103 84 72 64 59
191 134 109 95 84 77
299 211 172 149 133 121
152 107 87 75 67 61
239 168 137 119 106 97
300 243 198 171 153 140
300 300 270 234 209 191
199 140 114 99 88 80
287 202 165 143 127 116
300 276 225 195 174 159
300 300 295 255 228 208
246 173 141 122 109 99
300 236 193 167 149 136
300 300 252 218 195 178
300 300 300 277 247 226
300 300 300 300 300 279
293 207 169 146 130 119
300 271 221 191 171 156
300 300 280 242 216 197
300 300 300 299 267 244
300 300 300 300 300 295
Pivoted and Rigidly

Guided Rod End
Length (LA) at psi:
500 1000 1500 2000 2500 3000
35 25 20 17 16 14
91 64 52 45 40 37
68 48 39 33 30 27
129 91 74 64 57 52
54 38 31 26 23 21
103 72 59 51 45 41
167 118 96 83 74 67
79 55 45 39 34 31
128 90 73 63 56 51
168 118 96 83 74 68
104 73 59 51 46 41
136 96 78 67 60 54
213 150 122 106 95 86
108 76 62 53 47 43
170 120 98 84 75 68
246 173 141 122 109 99
300 236 193 167 149 136
142 100 81 70 62 57
205 144 117 101 91 83
279 197 160 139 124 113
300 258 210 182 162 148
175 123 100 87 77 71
239 168 137 119 106 97
300 221 180 155 139 127
300 280 228 197 176 161
300 300 282 244 218 199
209 147 120 104 93 84
273 193 157 136 121 111
300 244 199 172 154 140
300 300 246 213 191 174
300 300 298 258 231 211
Unguided Rod End

Length (LA) at psi:
500
12
31
23
44
18
35
58
27
44
58
35
46
74
37
58
85
116
48
71
97
127
60
83
108
138
170
72
95
120
149
180
1000 1500 2000 2500 3000

8
7
6
5
5
22 18 15 14 12
16 13 11 10 9
31 25 22 19 17
12 10 8
7
7
24 20 17 15 13
40 33 28 25 23
18 15 13 11 10
31 25 21 19 17
40 33 28 25 23
25 20 17 15 14
32 26 22 20 18
52 42 36 32 29
26 21 18 16 14
41 33 28 25 23
60 48 42 37 34
82 66 57 51 46
34 27 23 21 19
49 40 34 31 28
68 55 47 42 38
89 72 63 56 51
42 34 29 26 24
58 47 40 36 33
76 62 53 48 43
97 79 68 61 55
120 98 84 75 69
51 41 35 31 29
66 54 47 41 38
85 69 59 53 48
105 85 74 66 60
127 103 89 80 73
Maximum operating pressure is limited for the SB Mount. Please refer to maximum operating pressure per bore in SB Pressure Ratings table
on page 14.
68


Engineering Data
Piston Rod Selection Data
Maximum Basic Lengths (LA) (all dimensions in inches)

Bore Rod
Intermediate Pivot
Mount (DD)
Rear Fixed Mount (H)
Pivoted and Rigidly

Guided Rod End
Length (LA) at psi:
Fixed and Rigidly

Guided Rod End
Length (LA) at psi:
Pivoted and Rigidly

Guided Rod End
Length (LA) at psi:
Unguided Rod End

Length (LA) at psi:
500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000 500 1000 1500 2000 2500 3000
1.50
2.00
2.50
3.25
4.00
5.00
6.00
7.00
8.00
0.625
1.000
1.000
1.375
1.000
1.375
1.750
1.375
1.750
2.000
1.750
2.000
2.500
2.000
2.500
3.000
3.500
2.500
3.000
3.500
4.000
3.000
3.500
4.000
4.500
5.000
3.500
4.000
4.500
5.000
5.500
25
64
48
91
38
73
118
56
91
118
74
96
150
77
120
173
236
100
144
196
257
124
168
220
278
300
147
192
244
300
300
18
45
34
64
27
51
83
40
64
84
52
68
106
54
85
122
167
71
102
139
181
87
119
155
197
243
104
136
172
213
257
14
37
28
53
22
42
68
32
52
68
43
56
87
44
69
100
136
58
83
113
148
71
97
127
161
198
85
111
141
174
210
13
32
24
45
19
36
59
28
45
59
37
48
75
38
60
87
118
50
72
98
128
62
84
110
139
172
74
96
122
150
182
11
29
22
41
17
33
53
25
41
53
33
43
67
34
54
77
105
45
65
88
115
55
75
98
124
154
66
86
109
134
163
10
26
20
37
16
30
48
23
37
48
30
39
61
31
49
71
96
41
59
80
105
50
69
90
114
140
60
79
99
123
149
70
170
132
232
107
197
300
156
246
300
203
261
300
214
300
300
300
278
300
300
300
300
300
300
300
300
300
300
300
300
300
50
120
93
164
76
140
213
110
174
221
144
185
274
151
231
300
300
197
278
300
300
241
300
300
300
300
288
300
300
300
300
40
98
76
134
62
114
174
90
142
181
117
151
224
123
188
261
300
161
227
300
300
197
263
300
300
300
235
300
300
300
300
35
85
66
116
54
99
151
78
123
157
102
131
194
107
163
226
289
139
197
260
300
171
228
289
300
300
203
261
300
300
300
31
76
59
104
48
88
135
70
110
140
91
117
173
96
146
202
259
124
176
233
292
153
204
259
300
300
182
234
290
300
300
29
69
54
95
44
81
123
64
100
128
83
107
158
87
133
184
236
114
161
212
266
139
186
236
288
300
166
213
264
300
300
50
121
94
166
77
141
215
111
176
224
145
187
277
153
233
300
300
199
281
300
300
244
300
300
300
300
291
300
300
300
300
35
86
67
117
54
100
152
79
124
158
103
132
196
108
165
228
292
141
199
263
300
172
230
292
300
300
205
264
300
300
300
29
70
54
96
44
81
124
64
102
129
84
108
160
88
135
186
239
115
162
215
269
141
188
239
290
300
168
216
267
300
300
25
61
47
83
38
70
108
56
88
112
73
93
138
76
117
161
207
99
140
186
233
122
163
207
252
296
145
187
231
277
300
22
54
42
74
34
63
96
50
79
100
65
83
124
68
104
144
185
89
126
166
208
109
146
185
225
264
130
167
207
248
289
20
50
38
68
31
58
88
45
72
91
59
76
113
62
95
132
169
81
115
152
190
100
133
169
205
241
119
152
189
226
264
18
42
33
58
27
49
75
39
62
78
51
65
97
53
82
113
145
70
98
130
163
85
114
145
176
207
102
131
162
194
226
12
30
23
41
19
35
53
28
44
55
36
46
69
38
58
80
102
49
70
92
115
60
81
102
124
146
72
92
114
137
160
10
25
19
33
16
28
43
22
36
45
29
38
56
31
47
65
83
40
57
75
94
49
66
83
102
119
59
75
93
112
131
9
21
16
29
13
25
38
19
31
39
25
33
48
27
41
56
72
35
49
65
82
43
57
72
88
103
51
65
81
97
113
8
19
15
26
12
22
34
17
28
35
23
29
43
24
36
50
65
31
44
58
73
38
51
65
79
93
45
58
72
87
101
7
17
13
24
11
20
31
16
25
32
21
27
40
22
33
46
59
28
40
53
67
35
46
59
72
84
42
53
66
79
92
69


Engineering Data
Cylinder Safety Guide
Safety Guide for Selecting and Using Hydraulic, Pneumatic Cylinders and Their Accessories
WARNING:
FAILURE OF THE CYLINDER, ITS PARTS, ITS MOUNTING, ITS CONNECTIONS TO OTHER OBJECTS,
OR ITS CONTROLS CAN RESULT IN:

Unanticipated or uncontrolled movement of the cylinder or objects connected to it.

Falling of the cylinder or objects held up by it.

Fluid escaping from the cylinder, potentially at high velocity.
THESE EVENTS COULD CAUSE DEATH OR PERSONAL INJURY BY, FOR EXAMPLE, PERSONS FALLING FROM
HIGH LOCATIONS, BEING CRUSHED OR STRUCK BY HEAVY OR FAST MOVING OBJECTS, BEING PUSHED INTO
DANGEROUS EQUIPMENT OR SITUATIONS, OR SLIPPING ON ESCAPED FLUID.
Before selecting or using Parker Hannifin Corporation (the Company) cylinders
or related accessories, it is important that you read, understand and follow the
following safety information. Training is advised before selecting and using the
Companys products.
1.0 General Instructions

1.1 Scope This safety guide provides instructions for selecting and using
(including assembling, installing, and maintaining) cylinder products. This
safety guide is a supplement to and is to be used with the specific Company
publications for the specific cylinder products that are being considered for
use.
1.2 Fail Safe Cylinder products can and do fail without warning for many
reasons. All systems and equipment should be designed in a fail-safe mode
so that if the failure of a cylinder product occurs people and property wont be
endangered.
1.3 Distribution Provide a free copy of this safety guide to each person
responsible for selecting or using cylinder products. Do not select or use
the Companys cylinders without thoroughly reading and understanding this
safety guide as well as the specific Company publications for the products
considered or selected.
1.4 User Responsibility Due to very wide variety of cylinder applications

and cylinder operating conditions, the Company does not warrant that any
particular cylinder is suitable for any specific application. This safety guide
does not analyze all technical parameters that must be considered in selecting a product. The hydraulic and pneumatic cylinders outlined in this catalog
are designed to the Companys design guidelines and do not necessarily
meet the design guideline of other agencies such as American Bureau of
Shipping, ASME Pressure Vessel Code etc. The user, through its own
analysis and testing, is solely responsible for:
Making the final selection of the cylinders and related accessories.

Determining if the cylinders are required to meet specific design requirements as required by the Agency(s) or industry standards covering the
design of the users equipment.
Assuring that the users requirements are met, OSHA requirements are
met, and safety guidelines from the applicable agencies such as but not
limited to ANSI are followed and that the use presents no health or safety
hazards.
1.5 Additional Questions Call the appropriate Company technical service

department if you have any questions or require any additional information.
See the Company publication for the product being considered or used, or
call 1-847-298-2400, or go to www.parker.com, for telephone numbers of the
appropriate technical service department.
2.0 Cylinder and Accessories Selection

2.1 Seals Part of the process of selecting a cylinder is the selection of
seal compounds. Before making this selection, consult the seal information
page(s) of the publication for the series of cylinders of interest.
Unexpected detachment of the machine member from the piston rod.
The piston rod to piston and the stud to piston rod threaded connections are
secured with an anaerobic adhesive. The strength of the adhesive decreases
with increasing temperature. Cylinders which can be exposed to temperatures above +250F (+121C) are to be ordered with a non studded piston
rod and a pinned piston to rod joint.
2.3 Cushions Cushions should be considered for cylinder applications

when the piston velocity is expected to be over 4 inches/second.
Cylinder cushions are normally designed to absorb the energy of a linear
applied load. A rotating mass has considerably more energy than the same
mass moving in a linear mode. Cushioning for a rotating mass application
should be reviewed by our engineering department.
2.2 Piston Rods Possible consequences of piston rod failure or

separation of the piston rod from the piston include, but are not limited to are:
Piston rod and or attached load thrown off at high speed.
High velocity fluid discharge.
Piston rod extending when pressure is applied in the piston
retract mode.
The cylinder user should always make sure that the piston rod is securely
attached to the machine member.
On occasion cylinders are ordered with double rods (a piston rod extended
from both ends of the cylinder). In some cases a stop is threaded on to one
of the piston rods and used as an external stroke adjuster. On occasions
spacers are attached to the machine member connected to the piston rod
and also used as a stroke adjuster. In both cases the stops will create a pinch
point and the user should consider appropriate use of guards. If these
external stops are not perpendicular to the mating contact surface, or if debris
is trapped between the contact surfaces, a bending moment will be placed
on the piston rod, which can lead to piston rod failure. An external stop will
also negate the effect of cushioning and will subject the piston rod to impact
loading. Those two (2) conditions can cause piston rod failure. Internal stroke
adjusters are available with and without cushions. The use of external stroke
adjusters should be reviewed with our engineering department.
Dynamic seals will wear. The rate of wear will depend on many operating
factors. Wear can be rapid if a cylinder is mis-aligned or if the cylinder has
been improperly serviced. The user must take seal wear into consideration in
the application of cylinders.
Piston rods or machine members attached to the piston rod may move
suddenly and without warning as a consequence of other conditions
occurring to the machine such as, but not limited to:
The application of cylinders may allow fluids such as cutting fluids, wash
down fluids etc. to come in contact with the external area of the cylinder.
These fluids may attack the piston rod wiper and or the primary seal and
must be taken into account when selecting and specifying seal compounds.
Piston rods are not normally designed to absorb bending moments or loads
which are perpendicular to the axis of piston rod motion. These additional
loads can cause the piston rod to fail. If these types of additional loads are
expected to be imposed on the piston rod, their magnitude should be made
known to our engineering department.
Providing all appropriate health and safety warnings on the equipment on

which the cylinders are used.
Failure of the pressurized fluid delivery system (hoses, fittings, valves,

pumps, compressors) which maintain cylinder position.
Catastrophic cylinder seal failure leading to sudden loss of pressurized
fluid.
Failure of the machine control system.
Follow the recommendations of the Piston Rod Selection Chart and Data
in the publication for the series of cylinders of interest. The suggested piston
rod diameter in these charts must be followed in order to avoid piston rod
buckling.
2.4 Cylinder Mountings Some cylinder mounting configurations may have

certain limitations such as but not limited to minimum stroke for side or foot
mounting cylinders or pressure de-ratings for certain mounts. Carefully review
the catalog for these types of restrictions.
Always mount cylinders using the largest possible high tensile alloy steel
socket head cap screws that can fit in the cylinder mounting holes and torque
them to the manufacturers recommendations for their size.
2.5 Port Fittings Hydraulic cylinders applied with meter out or deceleration circuits are subject to intensified pressure at piston rod end.
The rod end pressure is approximately equal to:
operating pressure x effective cap end area
effective rod end piston area
Contact your connector supplier for the pressure rating of individual

connectors.
3.0 Cylinder and Accessories Installation and Mounting

3.1 Installation

3.1.1 Cleanliness is an important consideration, and cylinders are
shipped with the ports plugged to protect them from contaminants entering the ports. These plugs should not be removed until the piping is to
be installed. Before making the connection to the cylinder ports, piping
should be thoroughly cleaned to remove all chips or burrs which might
have resulted from threading or flaring operations.
70


Engineering Data
Cylinder Safety Guide

3.1.2 Cylinders operating in an environment where air drying materials
are present such as fast-drying chemicals, paint, or weld splatter, or
other hazardous conditions such as excessive heat, should have shields
installed to prevent damage to the piston rod and piston rod seals.
3.1.3 Proper alignment of the cylinder piston rod and its mating
component on the machine should be checked in both the extended and
retracted positions. Improper alignment will result in excessive rod gland
and/or cylinder bore wear. On fixed mounting cylinders attaching the piston rod while the rod is retracted will help in achieving proper alignment.
3.1.4 Sometimes it may be necessary to rotate the piston rod in order
to thread the piston rod into the machine member. This operation must
always be done with zero pressure being applied to either side of the
piston. Failure to follow this procedure may result in loosening the piston
to rod-threaded connection. In some rare cases the turning of the piston
rod may rotate a threaded head and loosen it from the cylinder body.
Confirm that this condition is not occurring. If it does, re-tighten the head
firmly against the cylinder body.

4.2.1.2 Cylinder body seal leak can generally be traced to a

loose head. Torque the head to manufacturers recommendation
for that bore size.
For double rod cylinders it is also important that when attaching or

detaching the piston rod from the machine member that the torque be
applied to the piston rod end of the cylinder that is directly attaching to
the machine member with the opposite end unrestrained. If the design
of the machine is such that only the rod end of the cylinder opposite to
where the rod attaches to the machine member can be rotated, consult
the factory for further instructions.
3.2 Mounting Recommendations

3.2.1 Always mount cylinders using the largest possible high tensile
alloy steel socket head screws that can fit in the cylinder mounting holes
and torque them to the manufacturers recommendations for their size.
Excessive pressure can also result in cylinder body seal leak.

Determine maximum pressure to rated limits. Replace seals and
retorque head as in paragraph above. Excessive pressure can also
result in cylinder body seal leak. Determine if the pressure rating of
the cylinder has been exceeded. If so, bring the operating pressure
down to the rating of the cylinder and have the head replaced.
Pinched or extruded cylinder body seal will also result in a leak.

Replace cylinder body seal and retorque as in paragraph above.
Cylinder body seal leakage due to loss of radial squeeze which
shows up in the form of flat spots or due to wear on the O.D. or I.D.
Either of these are symptoms of normal wear due to high cycle
rate or length of service. Replace seals as per paragraph above.
4.2.2 Internal Leakage

4.2.2.1 Piston seal leak (by-pass) 1 to 3 cubic inches per minute
leakage is considered normal for piston ring construction. Virtually
no static leak with lipseal type seals on piston should be expected.
Piston seal wear is a usual cause of piston seal leakage. Replace
seals as required.
4.2.2.2 With lipseal type piston seals excessive back pressure
due to over-adjustment of speed control valves could be a direct
cause of rapid seal wear. Contamination in a hydraulic system
can result in a scored cylinder bore, resulting in rapid seal wear. In
either case, replace piston seals as required.
3.2.3 Tie Rod Mounting Cylinders with tie rod mountings are recommended for applications where mounting space is limited. Nuts used for
this mounting style should be torqued to the same value as the tie rods
for that bore size.
3.2.4 Flange Mount Cylinders The controlled diameter of the rod
gland extension on head end flange mount cylinders can be used
as a pilot to locate the cylinders in relation to the machine. After alignment has been obtained, the flanges may be drilled for pins or dowels to
prevent shifting.
3.2.5 Trunnion Mountings Cylinders require lubricated bearing blocks

with minimum bearing clearances. Bearing blocks should be carefully
aligned and rigidly mounted so the trunnions will not be subjected to
bending moments. The rod end should also be pivoted with the pivot pin
in line and parallel to axis of the trunnion pins.
3.2.6 Clevis Mountings Cylinders should be pivoted at both ends
with centerline of pins parallel to each other. After cylinder is mounted,
be sure to check to assure that the cylinder is free to swing through its
working arc without interference from other machine parts.
4.2.2.3 What appears to be piston seal leak, evidenced by the

fact that the cylinder drifts, is not always traceable to the piston. To
make sure, it is suggested that one side of the cylinder piston be
pressurized and the fluid line at the opposite port be disconnected.
Observe leakage. If none is evident, seek the cause of cylinder drift
in other component parts in the circuit.
4.2.3 Cylinder Fails to Move the Load
4.2.3.1 Pneumatic or hydraulic pressure is too low. Check the
pressure at the cylinder to make sure it is to circuit requirements.
4.2.3.2 Piston Seal Leak Operate the valve to cycle the cylinder
and observe fluid flow at valve exhaust ports at end of cylinder
stroke. Replace piston seals if flow is excessive.
4.2.3.3 Cylinder is undersized for the load Replace cylinder with
one of a larger bore size.
4.0 Cylinder and Accessories Maintenance, Troubleshooting

and Replacement

4.1 Storage At times cylinders are delivered before a customer is ready to

install them and must be stored for a period of time. When storage is required
the following procedures are recommended.
4.1.1 Store the cylinders in an indoor area which has a dry, clean and
noncorrosive atmosphere. Take care to protect the cylinder from both
internal corrosion and external damage.
4.1.2 Whenever possible cylinders should be stored in a vertical position (piston rod up). This will minimize corrosion due to possible condensation which could occur inside the cylinder. This will also minimize seal
damage.
3.2.2 Side-Mounted Cylinders In addition to the mounting bolts,

cylinders of this type should be equipped with thrust keys or dowel pins
located so as to resist the major load.

4.3 Erratic or Chatter Operation
4.3.1 Excessive friction at rod bearing or piston bearing due to load
misalignment Correct cylinder-to-load alignment.
4.3.2 Cylinder sized too close to load requirements Reduce load or
install larger cylinder.
4.3.3 Erratic operation could be traced to the difference between static
and kinetic friction. Install speed control valves to provide a back pressure to control the stroke.

4.4 Cylinder Modifications, Repairs, or Failed Component Cylinders

as shipped from the factory are not to be disassembled and or modified.
If cylinders require modifications, these modifications must be done at
company locations or by the Companys certified facilities. The Industrial
Cylinder Division Engineering Department must be notified in the event of
a mechanical fracture or permanent deformation of any cylinder component
(excluding seals). This includes a broken piston rod, head, mounting
accessory or any other cylinder component. The notification should include
all operation and application details. This information will be used to provide
an engineered repair that will prevent recurrence of the failure.
It is allowed to disassemble cylinders for the purpose of replacing seals or

seal assemblies. However, this work must be done by strictly following all the
instructions provided with the seal kits.
4.1.3 Port protector plugs should be left in the cylinder until the time of
installation.
4.1.4 If a cylinder is stored full of hydraulic fluid, expansion of the fluid
due to temperature changes must be considered. Installing a check
valve with free flow out of the cylinder is one method.
4.1.5 When cylinders are mounted on equipment that is stored outside
for extended periods, exposed unpainted surfaces, e.g. piston rod, must
be coated with a rust-inhibiting compound to prevent corrosion.

Rod seal leakage could also be traced to bearing wear. If clearance is excessive, replace rod bearing and seal. Rod seal leakage
can also be traced to seal deterioration. If seals are soft or gummy
or brittle, check compatibility of seal material with lubricant used
if air cylinder, or operating fluid if hydraulic cylinder. Replace with
seal material, which is compatible with these fluids. If the seals are
hard or have lost elasticity, it is usually due to exposure to temperatures in excess of 165F. (+74C). Shield the cylinder from the
heat source to limit temperature to 350F. (+177C.) and replace
with fluorocarbon seals.
4.2 Cylinder Trouble Shooting
4.2.1 External Leakage

4.2.1.1 Rod seal leakage can generally be traced to worn or
damaged seals. Examine the piston rod for dents, gouges or score
marks, and replace piston rod if surface is rough.
71


Engineering Data
Offer of Sale
Offer of Sale
The items described in this document and other documents and descriptions provided by Parker Hannifin Corporation, its subsidiaries and its authorized distributors (Seller)
are hereby offered for sale at prices to be established by Seller. This offer and its acceptance by any customer (Buyer) shall be governed by all of the following Terms and
Conditions. Buyers order for any item described in its document, when communicated to Seller verbally, or in writing, shall constitute acceptance of this offer. All goods, services
or work described will be referred to as Products.
1. Terms and Conditions. Sellers willingness to offer Products, or accept an order
for Products, to or from Buyer is subject to these Terms and Conditions or any newer
version of the terms and conditions found on-line at www.parker.com/saleterms/. Seller
objects to any contrary or additional terms or conditions of Buyers order or any other
document issued by Buyer.
2. Price Adjustments; Payments. Prices stated on Sellers quote or other documentation offered by Seller are valid for 30 days, and do not include any sales, use, or other
taxes unless specifically stated. Unless otherwise specified by Seller, all prices are
F.C.A. Sellers facility (INCOTERMS 2010). Payment is subject to credit approval and
is due 30 days from the date of invoice or such other term as required by Sellers Credit
Department, after which Buyer shall pay interest on any unpaid invoices at the rate of
1.5% per month or the maximum allowable rate under applicable law.
3. Delivery Dates; Title and Risk; Shipment. All delivery dates are approximate and
Seller shall not be responsible for any damages resulting from any delay. Regardless
of the manner of shipment, title to any products and risk of loss or damage shall pass
to Buyer upon placement of the products with the shipment carrier at Sellers facility.
Unless otherwise stated, Seller may exercise its judgment in choosing the carrier and
means of delivery. No deferment of shipment at Buyers request beyond the respective dates indicated will be made except on terms that will indemnify, defend and hold
Seller harmless against all loss and additional expense. Buyer shall be responsible for
any additional shipping charges incurred by Seller due to Buyers acts or omissions.
4. Warranty. Seller warrants that the Products sold hereunder shall be free from
defects in material or workmanship for a period of eighteen months from the date of
delivery to Buyer. The prices charged for Sellers products are based upon the exclusive limited warranty stated above, and upon the following disclaimer: DISCLAIMER
OF WARRANTY: THIS WARRANTY COMPRISES THE SOLE AND ENTIRE
WARRANTY PERTAINING TO PRODUCTS PROVIDED HEREUNDER. SELLER
DISCLAIMS ALL OTHER WARRANTIES, EXPRESS AND IMPLIED, INCLUDING
DESIGN, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
5. Claims; Commencement of Actions. Buyer shall promptly inspect all Products
upon delivery. No claims for shortages will be allowed unless reported to the Seller
within 10 days of delivery. No other claims against Seller will be allowed unless
asserted in writing within 30 days after delivery. Buyer shall notify Seller of any alleged
breach of warranty within 30 days after the date the defect is or should have been
discovered by Buyer. Any action based upon breach of this agreement or upon any
other claim arising out of this sale (other than an action by Seller for an amount due on
any invoice) must be commenced within 12 months from the date of the breach without
regard to the date breach is discovered.
6. LIMITATION OF LIABILITY. UPON NOTIFICATION, SELLER WILL, AT ITS
OPTION, REPAIR OR REPLACE A DEFECTIVE PRODUCT, OR REFUND THE
PURCHASE PRICE. IN NO EVENT SHALL SELLER BE LIABLE TO BUYER FOR
ANY SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF, OR AS THE RESULT OF, THE SALE, DELIVERY, NONDELIVERY, SERVICING, USE OR LOSS OF USE OF THE PRODUCTS OR ANY
PART THEREOF, OR FOR ANY CHARGES OR EXPENSES OF ANY NATURE
INCURRED WITHOUT SELLERS WRITTEN CONSENT, EVEN IF SELLER
HAS BEEN NEGLIGENT, WHETHER IN CONTRACT, TORT OR OTHER LEGAL
THEORY. IN NO EVENT SHALL SELLERS LIABILITY UNDER ANY CLAIM MADE
BY BUYER EXCEED THE PURCHASE PRICE OF THE PRODUCTS.
7. User Responsibility. The user, through its own analysis and testing, is solely
responsible for making the final selection of the system and Product and assuring that
all performance, endurance, maintenance, safety and warning requirements of the
application are met. The user must analyze all aspects of the application and follow
applicable industry standards and Product information. If Seller provides Product or
system options, the user is responsible for determining that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses
of the Products or systems.
8. Loss to Buyers Property. Any designs, tools, patterns, materials, drawings, confidential information or equipment furnished by Buyer or any other items which become
Buyers property, will be considered obsolete and may be destroyed by Seller after two
consecutive years have elapsed without Buyer ordering the items manufactured using
such property. Seller shall not be responsible for any loss or damage to such property
while it is in Sellers possession or control.
9. Special Tooling. A tooling charge may be imposed for any special tooling, including without limitation, dies, fixtures, molds and patterns, acquired to manufacture
Products. Such special tooling shall be and remain Sellers property notwithstanding
payment of any charges by Buyer. In no event will Buyer acquire any interest in apparatus belonging to Seller which is utilized in the manufacture of the Products, even if
such apparatus has been specially converted or adapted for such manufacture and
notwithstanding any charges paid by Buyer. Unless otherwise agreed, Seller shall have
the right to alter, discard or otherwise dispose of any special tooling or other property
in its sole discretion at any time.
10. Buyers Obligation; Rights of Seller. To secure payment of all sums due or otherwise, Seller shall retain a security interest in the goods delivered and this agreement
shall be deemed a Security Agreement under the Uniform Commercial Code. Buyer
authorizes Seller as its attorney to execute and file on Buyers behalf all documents
Seller deems necessary to perfect its security interest.
11. Improper use and Indemnity. Buyer shall indemnify, defend, and hold Seller
harmless from any claim, liability, damages, lawsuits, and costs (including attorney
fees), whether for personal injury, property damage, patent, trademark or copyright
infringement or any other claim, brought by or incurred by Buyer, Buyers employees,

or any other person, arising out of: (a) improper selection, improper application or other
misuse of Products purchased by Buyer from Seller; (b) any act or omission, negligent
or otherwise, of Buyer; (c) Sellers use of patterns, plans, drawings, or specifications
furnished by Buyer to manufacture Product; or (d) Buyers failure to comply with these
terms and conditions. Seller shall not indemnify Buyer under any circumstance except
as otherwise provided.
12. Cancellations and Changes. Orders shall not be subject to cancellation or
change by Buyer for any reason, except with Sellers written consent and upon terms
that will indemnify, defend and hold Seller harmless against all direct, incidental and
consequential loss or damage. Seller may change product features, specifications,
designs and availability with notice to Buyer.
13. Limitation on Assignment. Buyer may not assign its rights or obligations under
this agreement without the prior written consent of Seller.
14. Force Majeure. Seller does not assume the risk and shall not be liable for delay
or failure to perform any of Sellers obligations by reason of circumstances beyond the
reasonable control of Seller (hereinafter Events of Force Majeure). Events of Force
Majeure shall include without limitation: accidents, strikes or labor disputes, acts of
any government or government agency, acts of nature, delays or failures in delivery
from carriers or suppliers, shortages of materials, or any other cause beyond Sellers
reasonable control.
15. Waiver and Severability. Failure to enforce any provision of this agreement will
not waive that provision nor will any such failure prejudice Sellers right to enforce that
provision in the future. Invalidation of any provision of this agreement by legislation or
other rule of law shall not invalidate any other provision herein. The remaining provisions of this agreement will remain in full force and effect.
16. Termination. Seller may terminate this agreement for any reason and at any time
by giving Buyer thirty (30) days written notice of termination. Seller may immediately
terminate this agreement, in writing, if Buyer: (a) commits a breach of any provision of
this agreement (b) appointments a trustee, receiver or custodian for all or any part of
Buyers property (c) files a petition for relief in bankruptcy on its own behalf, or by a third
party (d) makes an assignment for the benefit of creditors, or (e) dissolves or liquidates
all or a majority of its assets.
17. Governing Law. This agreement and the sale and delivery of all Products hereunder shall be deemed to have taken place in and shall be governed and construed
in accordance with the laws of the State of Ohio, as applicable to contracts executed
and wholly performed therein and without regard to conflicts of laws principles. Buyer
irrevocably agrees and consents to the exclusive jurisdiction and venue of the courts
of Cuyahoga County, Ohio with respect to any dispute, controversy or claim arising out
of or relating to this agreement.
18. Indemnity for Infringement of Intellectual Property Rights. Seller shall have
no liability for infringement of any patents, trademarks, copyrights, trade dress, trade
secrets or similar rights except as provided in this Section. Seller will defend and
indemnify Buyer against allegations of infringement of U.S. patents, U.S. trademarks,
copyrights, trade dress and trade secrets (Intellectual Property Rights). Seller will
defend at its expense and will pay the cost of any settlement or damages awarded in
an action brought against Buyer based on an allegation that a Product sold pursuant to
this Agreement infringes the Intellectual Property Rights of a third party. Sellers obligation to defend and indemnify Buyer is contingent on Buyer notifying Seller within ten
(10) days after Buyer becomes aware of such allegations of infringement, and Seller
having sole control over the defense of any allegations or actions including all negotiations for settlement or compromise. If a Product is subject to a claim that it infringes the
Intellectual Property Rights of a third party, Seller may, at its sole expense and option,
procure for Buyer the right to continue using the Product, replace or modify the Product
so as to make it noninfringing, or offer to accept return of the Product and return the
purchase price less a reasonable allowance for depreciation. Notwithstanding the foregoing, Seller shall have no liability for claims of infringement based on information
provided by Buyer, or directed to Products delivered hereunder for which the designs
are specified in whole or part by Buyer, or infringements resulting from the modification,
combination or use in a system of any Product sold hereunder. The foregoing provisions of this Section shall constitute Sellers sole and exclusive liability and Buyers
sole and exclusive remedy for infringement of Intellectual Property Rights.
19. Entire Agreement. This agreement contains the entire agreement between the
Buyer and Seller and constitutes the final, complete and exclusive expression of the
terms of sale. All prior or contemporaneous written or oral agreements or negotiations
with respect to the subject matter are herein merged.
20. Compliance with Law, U. K. Bribery Act and U.S. Foreign Corrupt Practices
Act. Buyer agrees to comply with all applicable laws and regulations, including both
those of the United Kingdom and the United States of America, and of the country or
countries of the Territory in which Buyer may operate, including without limitation the
U. K. Bribery Act, the U.S. Foreign Corrupt Practices Act (FCPA) and the U.S. AntiKickback Act (the Anti-Kickback Act), and agrees to indemnify and hold harmless
Seller from the consequences of any violation of such provisions by Buyer, its employees or agents. Buyer acknowledges that they are familiar with the provisions of the
U. K. Bribery Act, the FCPA and the Anti-Kickback Act, and certifies that Buyer will
adhere to the requirements thereof. In particular, Buyer represents and agrees that
Buyer shall not make any payment or give anything of value, directly or indirectly to
any governmental official, any foreign political party or official thereof, any candidate
for foreign political office, or any commercial entity or person, for the purpose of influencing such person to purchase products or otherwise benefit the business of Seller.
72

Parkers Motion & Control Technologies

At Parker, were guided by
a relentless drive to help
our customers become more
productive and achieve
higher levels of profitability by engineering the best
systems for their requirements. It means looking at
customer applications from
many angles to find new
ways to create value. Whatever the motion and control
technology need, Parker has
the experience, breadth of
product and global reach
to consistently deliver. No
company knows more about
motion and control technology than Parker. For further
info call 1 800 C-Parker
(1 800 272 7537).
AEROSPACE
Key Markets
Aircraft engines
Business & general aviation
Commercial transports
Land-based weapons systems
Military aircraft
Missiles & launch vehicles
Regional transports
Unmanned aerial vehicles
Key Products
Flight control systems
& components
Fluid conveyance systems
Fluid metering delivery
& atomization devices
Fuel systems & components
Hydraulic systems & components
Inert nitrogen generating systems
Pneumatic systems & components
Wheels & brakes
FLUID & GAS HANDLING

Key Markets
Aerospace
Agriculture
Bulk chemical handling
Construction machinery
Food & beverage
Fuel & gas delivery
Industrial machinery
Mobile
Oil & gas
Transportation
Welding
HYDRAULICS
Key Markets
Aerospace
Aerial lift
Agriculture
Construction machinery
Forestry
Mining
Oil & gas
Power generation & energy
Truck hydraulics
Key Products
Brass fittings & valves
Diagnostic equipment
Fluid conveyance systems
Industrial hose
PTFE & PFA hose, tubing &
plastic fittings
Rubber & thermoplastic hose
& couplings
Tube fittings & adapters
Quick disconnects
Key Products
Diagnostic equipment
Hydraulic cylinders
& accumulators
Hydraulic motors & pumps
Hydraulic systems
Hydraulic valves & controls
Power take-offs
Rubber & thermoplastic hose
& couplings
Tube fittings & adapters
Quick disconnects
CLIMATE CONTROL
Key Markets
Agriculture
Air conditioning
Food, beverage & dairy
Life sciences & medical
Precision cooling
Processing
Transportation
Key Products
CO2 controls
Electronic controllers
Filter driers
Hand shut-off valves
Hose & fittings
Pressure regulating valves
Refrigerant distributors
Safety relief valves
Solenoid valves
Thermostatic expansion valves
PNEUMATICS
Key Markets
Aerospace
Conveyor & material handling
Factory automation
Food & beverage
Life science & medical
Machine tools
Packaging machinery
Transportation & automotive
Key Products
Air preparation
Compact cylinders
Field bus valve systems
Grippers
Guided cylinders
Manifolds
Miniature fluidics
Pneumatic accessories
Pneumatic actuators & grippers
Pneumatic valves and controls
Rodless cylinders
Rotary actuators
Tie rod cylinders
Vacuum generators, cups & sensors
ELECTROMECHANICAL
Key Markets
Aerospace
Factory automation
Food & beverage
Life science & medical
Machine tools
Packaging machinery
Paper machinery
Plastics machinery & converting
Primary metals
Semiconductor & electronics
Textile
Wire & cable
Key Products
AC/DC drives & systems
Electric actuators
Controllers
Gantry robots
Gearheads
Human machine interfaces
Industrial PCs
Inverters
Linear motors, slides and stages
Precision stages
Stepper motors
Servo motors, drives & controls
Structural extrusions
PROCESS CONTROL
Key Markets
Chemical & refining
Food, beverage & dairy
Medical & dental
Microelectronics
Oil & gas
Power generation
Key Products
Analytical sample conditioning
products & systems
Fluoropolymer chemical delivery
fittings, valves & pumps
High purity gas delivery fittings,
valves & regulators
Instrumentation fittings, valves
& regulators
Medium pressure fittings & valves
Process control manifolds
FILTRATION
Key Markets
Food & beverage
Life sciences
Marine
Mobile equipment
Oil & gas
Power generation
Process
Transportation
Key Products
Analytical gas generators
Compressed air & gas filters
Condition monitoring
Engine air, fuel & oil filtration
& systems
Hydraulic, lubrication &
coolant filters
Process, chemical, water
& microfiltration filters
Nitrogen, hydrogen & zero
air generators
SEALING & SHIELDING

Key Markets
Aerospace
Chemical processing
Consumer
Energy, oil & gas
Fluid power
General industrial
Information technology
Life sciences
Military
Semiconductor
Telecommunications
Transportation
Key Products
Dynamic seals
Elastomeric o-rings
EMI shielding
Extruded & precision-cut,
fabricated elastomeric seals
Homogeneous & inserted
elastomeric shapes
High temperature metal seals
Metal & plastic retained composite seals
Thermal management
Smart phone scan here

can this QR code with your smart
S
phone to download the complete
RDH catalog. Look for QR code
readers at an "App Store" for your
mobile device.
05/12 / Catalog HY08-1320-2/NA

500 South Wolf Road
Des Plaines, IL 60016
phone (847) 298-2400
fax (800) 892-1008

Parker RDH 1320-2

Uploaded by

Copyright:

Available Formats

Parker RDH 1320-2

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Parker RDH 1320-2

Uploaded by

Copyright:

Available Formats

What products does Parker Hannifin offer?

What products does Parker Hannifin offer?

What are some of the key markets that Parker Hannifin serves?

What are some of the key markets that Parker Hannifin serves?

aerospace

Heavy Duty Hydraulic

Heavy Duty Hydraulic Roundline Cylinders

Parker Hannifin Corporation

Heavy Duty Hydraulic Roundline Cylinders

With annual sales exceeding

With our global presence in

Markets and Applications

Parker Hannifin Corporation

Series RDH Cylinders from Parker

All components are manufactured by Parker and designed for high

The Parker ALS Switch is the

Tri-lip rod seal (3 sealing edges!) and bi-directional piston seal

Switches can be located

Standard rod material is case-hardened, hard chrome plated

Proven Exterior Toughness

Composite Wear Rings

Outboard urethane rod wiper seal to

Strength characteristics meet or exceed most metals

High quality paint coating for interior or

Parker Hannifin Corporation

New Value from a Standard Platform

Cylinders, by nature, are customized

Parker Hannifin has utilized Lean

Organizing cylinder production and

We now follow Lean Implementation

Late-Day Orders our West

Non-Standard Designs since

Quick Delivery standard

lead time is a few days, with

Made-To-Order we are able to

Coast presence can create an

Risk Management the absence

50% of applications require

quickly manufacture customized

Parker Hannifin Corporation

Heavy Duty Hydraulic Roundline Cylinders

Customer Service Locations

Customer Service Locations

Tel.: (951) 280-3800

Fax: (951) 280-3808

Fax: (800) 869-9886

715 South Iroquois Street

Tel.: (219) 297-3182

Fax: (800) 328-8120

Tel.: (860) 749-2215

Fax: (800) 323-0105

Tel.: (734) 455-1700

Fax: (734) 455-1007

Lithia Springs, GA 30122

Tel.: (770) 819-3400

Fax: (800) 437-3498

Tel.: (541) 689-9111

Fax: (541) 688-6771

Fax: (800) 624-7996

Parker Hannifin Corporation