THERMAL POWER PLANTS Vol. I - Power Plant Combustion Theory - R.A.

Chaplin

POWER PLANT COMBUSTION THEORY

R.A. Chaplin
Department of Chemical Engineering, University of New Brunswick, Canada
Keywords: Combustion, Efficiency, Calorific Value, Combustion Products, Gas
Analysis
Contents

U
SA NE
M SC
PL O
E
C EO
H
AP LS
TE S
R
S

1. Combustion Fundamentals
1.1. Definitions of combustion
1.2. Principles of Combustion
1.3. Combustion Equations
2. Combustion Calculations
2.1. Concept of the Mole
2.2. Composition of Air
2.3. Excess Air Requirements
3. Energy Balances
3.1. Plant Efficiency
3.2. Boiler Efficiency (Input-Output Method)
3.3. Boiler Efficiency (Heat Loss Method)
4. Air-Fuel Ratios
4.1. Review
4.2. Exhaust Gas Analysis
4.3. Methods of Calculation
4.3.1. The Mole Method
4.3.2. The Joule Method (BTU Method)
5. Heat of Combustion
5.1. Calorific Value
5.2. Higher and Lower Heating Values
5.3. Combustion Temperatures
6. Combustion products
6.1. General
6.2. Nitrogen Oxides
6.3. Sulfur Dioxides
Glossary
Bibliography
Biographical Sketch
Summary

When a simple fuel such as carbon is burned in air, it combines with the oxygen to
produce carbon dioxide. If a hydrocarbon fuel is burned then, in addition, water is
produced from the hydrogen. Similarly various combustible impurities, such as sulfur,
produce their respective oxides, in this case sulfur dioxide.

Encyclopedia of Life Support Systems (EOLSS)

THERMAL POWER PLANTS Vol. I - Power Plant Combustion Theory - R.A. Chaplin

Simple chemical balances of the reactants and products enable the quantities required or
produced to be determined. Ideally there should be no reactants left over in the products
to obtain chemically correct or stoichiometric combustion. The nitrogen in the air has to
be taken into account. Although it passes through the combustion process essentially
unreacted, it does dilute both the reactants and the products. The chemical equation
describing the combustion process therefore must include an amount of nitrogen on
each side. With this taken into account the required air-fuel mass ratios can be
determined for any particular fuel.

U
SA NE
M SC
PL O
E
C EO
H
AP LS
TE S
R
S

Similarly it is possible to work backwards from a chemical analysis of the exhaust gas,
using the combustion equations, to determine the fuel constituents or air-fuel ratio. This
is a convenient method of monitoring the combustion efficiency of the boiler. In
practice, for complete combustion of the fuel, it is necessary to provide some excess air
beyond that necessary for stoichiometric conditions so some oxygen usually appears in
the exhaust gas.
It is also possible to determine the boiler thermal efficiency from an exhaust gas
analysis. The flue gas carries away a considerable amount of heat which is not
transferred to the water-steam circuit. Knowledge of the heating value of the fuel, the
gas-fuel ratio, the specific heat of the gases and their exhaust temperature is sufficient to
determine the boiler efficiency which is usually around 90 percent for large units.
1. Combustion Fundamentals

1.1. Definitions of combustion

Combustion is the rapid chemical combination of oxygen with certain elements.

Although similar to oxidation, it occurs very much faster and requires a certain
minimum temperature to initiate the reaction. This rapid chemical reaction can be
controlled so that, in normal circumstances, it is not explosive. For effective combustion
the reacting elements must be mixed with the oxygen, maintained at a suitable
temperature and given sufficient time to react. Hence the three Ts of combustion,
turbulence, temperature and time, which determine the success or otherwise of a
combustion process. Combustion processes release heat so generally, once ignition has
been accomplished, the temperature is maintained at a suitable value. As combustion
proceeds the concentration of the oxygen and the reacting elements decreases and
continued turbulence is required to bring unreacted elements into contact with the
oxygen. Adequate time is thus required from initial ignition to affect complete
combustion.
1.2. Principles of Combustion
The most suitable combustible fuels are those made up primarily of carbon or
hydrocarbons where the main constituents are carbon and hydrogen. All fossil fuels
derived originally from carboniferous matter fall into this category. Other elements such
as sulfur are also combustible and, if present in the fuel, contribute to the generation of
heat but produce undesirable products such as sulfur dioxide. Pure hydrocarbon fuels
have the advantage of producing carbon dioxide and water vapor, both relatively

Encyclopedia of Life Support Systems (EOLSS)

THERMAL POWER PLANTS Vol. I - Power Plant Combustion Theory - R.A. Chaplin

innocuous products. Oxygen is readily available from the atmosphere but is not pure.
The major constituent of the air is nitrogen and, although the relatively inert gas passes
through the combustion process largely unreacted, it does produce some undesirable
nitrogen oxide at high temperatures. Generally combustion for large scale heat
production should proceed continuously under stable conditions. This implies that the
fuel and oxygen must be supplied to the combustion zone continuously and the products
of combustion likewise removed. Within the combustion zone the air containing oxygen
must be brought into intimate contact with the fuel, irrespective of whether it is in
gaseous, liquid or solid form. This requires that fuel be well dispersed and the air
turbulent in the combustion zone. Liquid and solid fuels require suitable division into
small particles to ensure intimate mixing with the air.

U
SA NE
M SC
PL O
E
C EO
H
AP LS
TE S
R
S

Solid fuels usually produce significant amounts of ash which must be removed from the
combustion zone but only after sufficient time has been allowed for the combustible
elements within the fuel particles to have fully reacted with the oxygen of the air.
The purpose of combustion is to produce heat which is radiated from the combustion
zone or carried away by the gaseous products of combustion. This heat is to be
transferred effectively to the working fluid of the thermodynamic cycle but a certain
portion is inevitably lost to the environment when the exhaust gases are discharged to
the atmosphere.
1.3. Combustion Equations

When various elements are burned in oxygen the products of the combustion process
can be determined from basic chemical equations.
When a solid fuel such as carbon is used, the product is carbon dioxide:
C + O 2 = CO 2

(1)

When a simple gaseous fuel such as methane is burned, water vapor as well as carbon
dioxide is produced:
CH 4 + 2O 2 = CO 2 + 2H 2 O

(2)

For more complex liquid hydrocarbon fuels, such as oil, which contain mixtures of
different hydrocarbons, the equations have to be written in a slightly different form and
the amount of each element in the fuel has to be considered.
2. Combustion Calculations
2.1. Concept of the Mole
Each element has a specific atomic mass and each compound a specific molecular mass.
These values are based on the number of protons and neutrons in the atom and, as such,
are somewhat arbitrary masses. Carbon has an atomic mass of 12, oxygen an atomic

Encyclopedia of Life Support Systems (EOLSS)

THERMAL POWER PLANTS Vol. I - Power Plant Combustion Theory - R.A. Chaplin

mass of 16 while carbon dioxide has a molecular mass of 44.

The mass of a substance in kilograms equal to its molecular mass is called a kilogrammole or often simply a mole of the substance. In the case of oxygen combining with
carbon, converting to moles yields
C + O2 = CO2
12 kg-mole C + 32 kg-mole O2 = 44 kg-mole CO2
12 kg C + 32 kg O2 = 44 kg CO2

U
SA NE
M SC
PL O
E
C EO
H
AP LS
TE S
R
S

This demonstrates a method of carrying out combustion calculations where an amount

of a reactant or a product is to be determined.
In the case of a gas the volume occupied by one mole is called the molar volume. The
volume of one mole of an ideal gas is the same for all gases at any particular
temperature and pressure. One mole of oxygen therefore occupies the same volume as
one mole of carbon dioxide even though their masses are different.
This concept allows the conversion from volumes to masses. Therefore, if the
constituents of a gas are known by volume, their respective masses can be determined.
Thus a mixture of 50 percent carbon dioxide and 50 percent oxygen contains one mole
of CO2 for each mole of O2 but 44 kg of CO2 for every 32 kg of O2.
2.2. Composition of Air

Atmospheric air is composed of 78 percent nitrogen, 21 percent oxygen, 1 percent argon

and trace amounts of carbon dioxide and other gases. For the purpose of calculations the
argon and nitrogen are lumped together as atmospheric nitrogen to make up 79
percent. The ratio of nitrogen to oxygen is thus 3.76.
In all practical applications of combustion the oxygen is supplied as a constituent of
atmospheric air and the nitrogen passes through essentially unreacted. In effect the
nitrogen dilutes both the oxygen and the combustion products and appears on both sides
of the combustion equation. For carbon burning in air the combustion equation is thus:
C + O2 + 3.76 N2 = CO2 + 3.76 N2

From a chemical point of view this is no different from the previous equation except
that nitrogen has been added and a mass balance using the mole concept yields the
following:
12 kg C + 32 kg O2 + 105.3 kg N2 = 44 kg CO2 + 105.3 kg N2
The procedure enables the amount of air required to burn a certain quantity of fuel to be
determined. In this case the air-fuel ratio is:

Encyclopedia of Life Support Systems (EOLSS)

THERMAL POWER PLANTS Vol. I - Power Plant Combustion Theory - R.A. Chaplin

mair mfuel = 11.44 kg air / kg fuel

This assumes that combustion occurs under chemically correct or stoichiometric
conditions and that all the fuel is completely reacted with all the oxygen.
2.3. Excess Air Requirements

U
SA NE
M SC
PL O
E
C EO
H
AP LS
TE S
R
S

Stoichiometric combustion conditions as described above are an ideal situation difficult

to achieve in practice. As the oxygen and fuel are consumed, the remaining reactants
become more dilute and more time is required for them to come into contact with one
another. Even with good turbulence it is unlikely that the last remaining particles of fuel
will react with the highly diluted oxygen remnants. The result is that a certain amount of
unreacted fuel and oxygen will leave the combustion space.
To overcome this problem the quantity of air supplied is increased slightly above the
theoretical air amount. During the last stages of combustion there will thus be
significantly more oxygen in the combustion mixture so that the possibility of reaction
with the last remaining particles of fuel is much enhanced. In this way virtually
complete combustion can be ensured but some oxygen will pass through unreacted.
Most combustion processes operate with a certain amount of excess air which can be
accounted for in the combustion calculations by multiplying the theoretical air quantity
by the appropriate factor. For say 25 percent excess air, this factor is 1.25 and the
combustion equation for burning carbon becomes:
C + 1.25 (O2 + 3.76 N2) = CO2 + 0.25 O2 + 4.70 N2

Converting this to kilogram-moles to obtain a mass balance gives the following

12 kg C + 40 kg O2 + 131.6 kg N2 = 44 kg CO2 + 8 kg O2 + 131.6 kg N2

The corresponding air fuel ratio to give 25 percent excess air is then given by:
mair mfuel = 14.3kg air / kg fuel

TO ACCESS ALL THE 17 PAGES OF THIS CHAPTER,

Visit: http://www.eolss.net/Eolss-sampleAllChapter.aspx
Bibliography
ASME Power Test Code, PTC 4.1 (1964). Steam Generating Units, ASME.[ This code gives detailed
methods for calculating boiler efficiency. It includes standardized routines for combustion calculations]

Encyclopedia of Life Support Systems (EOLSS)

THERMAL POWER PLANTS Vol. I - Power Plant Combustion Theory - R.A. Chaplin

Black & Veatch (1996). Power Plant Engineering, Chapman & Hall.[ Good general text on power plant
design with chapters on various topics by specialists in the field]
British Electricity International (1991). Modern Power Station Practice, Volume B, Boilers and Ancillary
Plant, Pergamon Press.[ Good specialized text on boiler plant design and operation]
Cengel Y.A. & Boles M.A. (1989). Thermodynamics, an Engineering Approach, McGraw-Hill.[ Basic
thermodynamic text with chapter on combustion and combustion calculations]
Singer J.G. editor (1991). Combustion Fossil Power, Combustion Engineering ABB.[ Detailed text on
boiler design and operation. Includes material on fuels and combustion]
Stultz S.C. & Kitto J.B. editors (1992). Steam, Its Generation and Use, Babcock and Wilcox. [Excellent
text on boiler plant design and operation. Includes chapters on all types of fuels and combustion as well
as environmental controls and effluent treatment]

U
SA NE
M SC
PL O
E
C EO
H
AP LS
TE S
R
S

Biographical Sketch

Robin Chaplin obtained a B.Sc. and M.Sc. in mechanical engineering from University of Cape Town in
1965 and 1968 respectively. Between these two periods of study he spent two years gaining experience
in the operation and maintenance of coal fired power plants in South Africa. He subsequently spent a
further year gaining experience on research and prototype nuclear reactors in South Africa and the United
Kingdom and obtained M.Sc. in nuclear engineering from Imperial College of London University in
1971. On returning and taking up a position in the head office of Eskom he spent some twelve years
initially in project management and then as head of steam turbine specialists. During this period he was
involved with the construction of Ruacana Hydro Power Station in Namibia and Koeberg Nuclear Power
Station in South Africa being responsible for the underground mechanical equipment and civil structures
and for the mechanical balance-of-plant equipment at the respective plants. Continuing his interests in
power plant modeling and simulation he obtained a Ph.D. in mechanical engineering from Queen=s
University in Canada in 1986 and was subsequently appointed as Chair in Power Plant Engineering at the
University of New Brunswick. Here he teaches thermodynamics and fluid mechanics and specialized
courses in nuclear and power plant engineering in the Department of Chemical Engineering. An
important function is involvement in the plant operator and shift supervisor training programs at Point
Lepreau Nuclear Generating Station. This includes the development of material and the teaching of
courses in both nuclear and non-nuclear aspects of the program.

Encyclopedia of Life Support Systems (EOLSS)