Fluids and Solids Handling

Nitrogen:
A Security Blanket for the
Chemical Industry
Bill Carlson,
Neutronics Inc.

rce

ou

www.aiche.org/cep November 2011 CEP

nS

50

itio

The benefits
Blanketing helps protect plant personnel, products,
and plant assets by reducing the oxygen content in the
vapor space of a storage tank or process vessel, making it
inert. This eliminates the possibility of fire or explosion,
decreases evaporation, and protects the tank from structural corrosion damage caused by air and moisture. It also
prevents air, moisture, or other contaminants from entering the vapor space and causing product degradation.

Quality benefits. Some sensitive materials, especially

in the food, pharmaceutical, and nutraceutical industries,
may experience quality degradation when they come into
contact with oxygen, moisture, or other contaminants.
Blanketing creates a slight positive pressure inside storage
containers, which prevents air and other contaminants
from infiltrating and causing oxidative degradation and
spoilage. The result is increased shelf life.
For example, oxygen and water vapor in the air cause
undesirable reactions in edible oils, which are triglycerides. Water reacts with a triglyceride to form a diglyceride
and a fatty acid. Oxygen reacts with the unsaturated fatty
acids to form fat hydroperoxides (and other undesirable

Ign

lthough nitrogen blanketing is a simple practice

that is widely used in the chemical, pharmaceutical, food processing, and petroleum refining
industries, its potential to improve productivity and safety
is often overlooked. Blanketing is the process of applying
a gas to the vapor space of a container or vessel in order to
control its composition. It can be implemented during production, storage, transportation, and final packaging, and
can be used in a wide variety of containers ranging in size
from storage tanks with capacities of millions of gallons to
quart-size or smaller bottles.
Nitrogen is the most commonly used gas for blanketing because it is inert, widely available, and relatively
inexpensive on virtually any scale. Other gases, such
as carbon dioxide or argon, are also occasionally used;
however, carbon dioxide is more reactive, and argon is
about five to ten times more expensive, depending on the
volume, location, etc.
This article discusses the basics of nitrogen blanketing
and explains how to implement it effectively and efficiently.

ge
n

Joe Dumoit
Cashco, Inc.

The benefits of nitrogen blanketing include

improved process safety, better product quality,
and longer equipment life.
Heres how to achieve the desired safety or quality
results while minimizing costs.

Ox
y

Paul Yanisko and Shiying Zheng

Air Products

Fuel

p Figure 1. The fire triangle depicts the three elements needed for a fire:
fuel, oxygen, and an ignition source.

Table 1. NFPA 69 (1) contains a full table of limiting oxygen

concentrations (LOC), such as those listed here for some
common materials at ambient temperature and pressure.
Material

LOC, vol. % O2

Propylene Oxide

5.8

Methanol

8.0

Ethanol

8.5

Acetone

9.5

Benzene

10.1

Vinyl Chloride

13.4

port combustion, i.e., the lower explosive limit (LEL) or

lower flammability limit (LFL)
increasing the fuel concentration in the vapor space
to a value greater than the maximum concentration that
can support combustion, i.e., the upper explosive limit
(UEL) or upper flammability limit (UFL).
A materials LEL and UEL (Figure 2) can be found
in the material safety data sheet (MSDS) provided by the
manufacturer. LOC values for many chemicals (e.g., Table
1) can be found in chemical engineering and chemistry
handbooks as well as in the National Fire Protection Associations NFPA 69: Standard on Explosion Prevention Systems (1). Computational methods can be used to determine
the flammability limits of mixtures of gases, fuels, and inert
substances at elevated temperatures and pressures (2).
The safety implications of improper handling of flammable or combustible materials are severe. Yet, at some
manufacturing plants, there is a false sense of security and
a general belief that it cant happen here. Consequently,
inerting and blanketing are often overlooked during safety
reviews, maintenance turnarounds, or upgrade projects.
The lack of blanketing or inadequate blanketing of flammable products has resulted in serious fires and explosions.
In one incident, explosions and fire erupted at the
Barton Solvents facility in Valley Center, KS, on July 17,
2007. The accident led to the evacuation of thousands

90
Concentration of Fuel in N2/O2 Mixture

products), which may further react to form undesirable

polymers, acids, and aldehydes. Exposure to air reduces
the oils stability and alters the oils color, flavor, and
aroma. Nitrogen blanketing of edible-oil storage tanks,
transfer lines, and railcars removes both oxygen and water
vapor from these containers and prevents oxidation of the
phospholipids, triglycerides, and free fatty acids making this a simple and effective way to maintain the integrity of the oil.
Safety benefits. Tank blanketing provides the greatest benefit safety in industries where combustible,
flammable, or explosive materials are processed, stored,
or generated. Blanketing prevents these types of products
from coming into contact with the oxygen in air, thereby
creating a nonflammable environment that prevents fire
and explosion.
A fire requires three elements (Figure 1): fuel, oxygen,
and an ignition source. Removing any one of these three
elements from the environment eliminates the possibility
of fire.
The headspace of a storage tank contains a mixture of
air and the vapor of the flammable material being stored
(e.g., a solvent). The mixture of solvent vapor and air
may ignite and burn if the vapor mixture is within the
solvents flammability limits and an ignition source is
present. Even if storage tanks are electrically grounded
to reduce the probability of ignition, static charges can
develop within the system or within the solvent itself and
act as an ignition source. Since it is practically impossible
to completely eliminate sources of static charge, and the
fuel cannot be eliminated because it is the material being
stored, oxygen is the only leg of the fire triangle that can
be controlled.
A storage tank can be made inert by:
reducing the oxygen content of the vapor space to a
value that is less than the concentration that will support
combustion, i.e., the limiting oxygen concentration (LOC)
reducing the fuel concentration in the vapor space to
a value less than the minimum concentration that can sup-

80

UEL

70
60
50
Flammability Envelope

40

LOC

30
20
10
LEL
0

21

14
7
Concentration of O2 in N2

p Figure 2. A flammability diagram illustrates the materials flammability

envelope, which is bounded by the lower and upper explosive limits (LEL
and UEL) and the limiting oxygen concentration (LOC). This diagram is for
hydrogen in air at standard temperature and pressure, for which LEL =
4.0%, UEL = 75.0%, and LOC = 5.0%.

CEP November 2011 www.aiche.org/cep

51

Fluids and Solids Handling

Vent

Vent

Vapor Space

No
Vapor Space

Potential Vapors

Liquid

Liquid

Liquid

Fixed Roof
Commonly N2 Blanketed

Floating Roof
Never N2 Blanketed

Covered Floating Roof

Occasionally N2 Blanketed

p Figure 3. The type of vessel is an important consideration when designing a new or retrofit tank blanketing system.

of residents and resulted in projectile damage offsite, as

well as extensive damage to the facility. The U.S. Chemical Safety and Hazard Review Board (CSB) conducted a
thorough investigation (3) to identify the root cause and
recommend preventive actions. The key findings were
that static electricity, which accumulated in storage tanks
during the transfer and storage of a nonconductive flammable liquid, ignited flammable vapor-air mixtures inside
the storage tanks. An important recommendation from the
investigation was to add inert-gas blanketing to the tank to
reduce the concentration of oxygen in the headspace.

Types of vessels
When considering a new blanketing design or an
upgrade to an existing installation, the first factor to
consider is the type of vessel. This will determine whether

blanketing is needed and, if so, the appropriate means of

control (pressure or concentration).
The most common type of tank (Figure 3) is the
fixed-roof tank. When flammable or sensitive materials are stored in fixed-roof tanks, nitrogen blanketing is
highly recommended. Floating-roof tanks usually are not
blanketed because there is no headspace where vapor
could build up. The headspace above the internal roof of a
covered floating-roof tank (or internal-floating-roof tank)
is occasionally blanketed.
Some enclosed spaces that do not hold pressure, such
as pneumatic conveyors, hoppers that contain powders
and dust, or controlled-atmosphere containers, may also
Tank
Blanketing
Valve
N2

p Figure 4. A self-contained, pilot-operated tank blanketing valve controls

the flowrate of nitrogen based on pressure. Photo courtesy of Cashco, Inc.

52

www.aiche.org/cep November 2011 CEP

Conservation
Vent

PSV
A

p Figure 5. A tank equipped with pressure-controlled blanketing adds

nitrogen via the tank blanketing valve when the liquid level drops, and vents
nitrogen through the conservation vent when the liquid level rises.

require blanketing. Nitrogen blanketing systems are

essential in spaces that are not sealed tight enough to hold
a slight positive pressure.

Nitrogen control by continuous purge

Three methods are commonly used for nitrogen control: continuous purge, pressure control, and concentration
control.
Continuous purge systems employ a constant flow
of nitrogen. This approach, while simple, has several
disadvantages. First, its nitrogen consumption rate is high.
In addition, the flowing nitrogen may strip the vapors in
the headspace and place an additional load on the plants
air-emission control system. And, air can infiltrate the
headspace if the tank discharges too quickly and the liquid
level drops too fast.
Despite these shortcomings, however, continuous
purge systems remain in use because they can be implemented quickly and easily. Retrofitting existing continuous-purge blanketing systems with pressure or concentration controls (discussed in the next two sections) will
usually reduce costs.
Pressure control
Pressure-control systems are employed for sealed
tanks, which hold pressure. A valve (Figure 4) senses
the pressure in the headspace of the tank and delivers
nitrogen accordingly. The headspace pressure can be set
quite low less than 1 in. w.c. is sufficient. As the tank
discharges, the liquid level falls, the pressure drops,
and nitrogen is added; as the tank is filling, the pressure
rises, and nitrogen exits through a vent valve (Figure 5).
Several pressure-control systems are available in the
marketplace.
The amount of nitrogen required to blanket a tank
under pressure control is the sum of the nitrogen required
based on the tanks working throughput (NW) and the
nitrogen required by thermal breathing, i.e., the rise and
fall of the liquid level due to the external temperature
changes (NTB). The total volume of nitrogen needed can be
calculated by the following simplified equations:
N T = N W + N TB
VT
N W = 7.48
T -T
1
N TB = V HS a max555 min ka 7.48 k F

(1)
(2)
(3)

where NT = total volume of nitrogen required per month,

ft3; NW = nitrogen required by the material flow through
the tank, ft3; NTB = nitrogen required by thermal breathing,
ft3; VT = total volume of material discharged from the tank
per month, gal; VHS = average empty headspace, gal;

Tmax = maximum temperature in the tank, F; Tmin = minimum temperature in the tank, F; F = estimated number of
temperature swings per month; 7.48 is the factor to convert
gallons to cubic feet; and 555 is a constant related to the
vapor space expansion factor, R.
The working-throughput component, NW, can be calculated easily from the total volume of liquid discharged
from each tank per month. The thermal breathing component, NTB, is a function of the size of the tank, the average liquid level in the tank, and atmospheric conditions
affecting the temperature in the tank (which vary due to
changing weather). Furthermore, the actual temperature
in the headspace of the tank is not always the same as
the ambient air temperature on sunny days, it is much
higher, which in turn causes larger temperature swings
and increases nitrogen consumption. But because thermal breathing is usually much smaller than the working
throughput, the uncertainties associated with calculating
NTB result in relatively small errors in estimating total
nitrogen usage per month.
The peak nitrogen usage, however, can be surprisingly
Table 2. For nonrefrigerated, uninsulated aboveground
tanks larger than 840,000 gal, peak nitrogen requirements
due to thermal breathing are specified in
API Standard 2000 (3) and ISO 28300 (4).
Tank Capacity

N2 Inbreathing
Requirement, scfh

bbl

gal

20,000

840,000

20,000

25,000

1,050,000

24,000

30,000

1,260,000

28,000

35,000

1,470,000

31,000

40,000

1,690,000

34,000

45,000

1,890,000

37,000

50,000

2,100,000

40,000

60,000

2,520,000

44,000

70,000

2,940,000

48,000

80,000

3,360,000

52,000

90,000

3,790,000

56,000

100,000

4,200,000

60,000

120,000

5,040,000

68,000

140,000

5,880,000

75,000

160,000

6,720,000

82,000

180,000

7,560,000

90,000

Note: API 2000 includes tanks smaller than 20,000 bbl (840,000 gal). The
absence of such tanks here does not imply that smaller tanks do not
experience thermal breathing. Rather, for smaller tanks, the nitrogen
blanketing requirements due to thermal breathing are calculated using
Eq. 4, which does not include the G term of Eq. 5.

CEP November 2011 www.aiche.org/cep

53

Fluids and Solids Handling

large due to rapid temperature changes. The peak nitrogen

requirement and its frequency of occurrence are important
for selecting and sizing the nitrogen supply system.
The peak usage can be estimated by the following
simplified equations:
N max = 8.021P + 0.02382C
N max = 8.021P + G

for tanks up to 840, 000 gal (4)

for tanks larger than 840, 000 gal (5)

where Nmax = maximum nitrogen flowrate, scfh; P = pumpout rate, gpm; C = total tank capacity, gal; 8.021 is the
factor to convert from gpm to scfh; 0.02382 is a factor
based on cooling an empty tank from a high of 120F at
rate of change of 100R/h; and G is the nitrogen breathing
requirement, scfh, obtained from Table 2.

Concentration control
Concentration control is suitable for unsealed tanks,
which cannot hold pressure. It is very efficient nitrogen usage is optimized because it is only added when it is
needed. An oxygen analyzer (Figure 6) directly measures
the actual oxygen concentration in the headspace vapor
and uses it to control the flow of nitrogen to the tank. The
conditions of most processes are much too harsh to permit
the use of an in situ oxygen sensor. Thus, the sample-conditioning equipment (Figure 7) is an integral part of the
analyzer system. A properly designed sample-conditioning

system allows the analyzer to measure reliably over a

wide range of process conditions, including extremes in
pressure, vacuum, and temperature, as well as in heavyparticulate and high-moisture environments.
The advantage of continuous concentration monitoring and control is that it conserves nitrogen by optimizing
nitrogen usage. The savings can provide an accelerated
payback on the cost of the monitoring and control equipment. Several commercially available systems are on the
market, with varying degrees of complexity and in various
price ranges.

Nitrogen supply
Nitrogen supply options include delivered liquid nitrogen stored in bulk or microbulk tanks or dewars, as well as
delivered gaseous nitrogen stored in large tubes, cylinder
banks, or cylinders. In addition, nitrogen can be generated

Nitrogen Supply Header

Vapor Condenser

Flowmeter

Oxygen Sensor

Oxygen
Analyzer/Controller

Sample Conditioning
System

Process Vessel
Drive Gas
Port

p Figure 6. A concentration-control system directly measures the oxygen

in the headspace and meters nitrogen to the tank to maintain the desired
setpoint.

54

www.aiche.org/cep November 2011 CEP

Aspirator

Flow
Switch

Sample
Port

Sample
Filter

p Figure 7. A concentration-control system relies on oxygen analyzers

(above top) and a sample conditioning system (above bottom). The latter
enables the analyzer to provide reliable measurement even at extreme
conditions of temperature, pressure, particulate loading, or moisture level.
Photos courtesy of Neutronics, Inc.

onsite by a cryogenic plant, or by pressure-swing adsorption (PSA) or membrane units.

The choice of delivery method depends on the applications requirements for purity, usage pattern, volume,
portability, footprint, and local power cost. New blanketing applications require calculations of nitrogen consumption based on tank volumes and throughputs, as discussed
previously. When optimizing existing installations, the
result of these calculations should also be compared with
actual flow data taken from the plants existing nitrogen
lines over a period of time, usually about a week.
Nitrogen costs can be reduced if a lower purity can
be accepted. A PSA or membrane nitrogen generator can
produce nitrogen at any purity, and the lower the purity,
the lower the unit cost. NFPA 69 requires operating at 60%
of the LOC, which for many flammable materials is in the
neighborhood of 10%. Thus, operating at 94% nitrogen
would meet NFPA guidelines, although a more conservative 25% of the LOC, or 97.5%, adds a larger safety buffer.
A purity of 9497.5% can be inexpensively supplied
by a membrane or PSA unit. Applications that use blanketing primarily for quality benefits may be able to use lowerpurity nitrogen. For example, certain edible oils may
be blanketed with nitrogen in this purity range depending on the desired oil quality, shelf life, and prevailing
storage conditions such as temperature and materials of
construction.
Usage pattern is another important parameter that
determines the appropriate delivery method. A plants
usage pattern can be determined by measuring the nitrogen flowrate over time, typically one week. There are
three basic usage patterns:
constant baseline the flow is constant, such as the
blanketing of a large tank farm. Onsite generation is an
excellent choice for this pattern.
erratic the flows are inconsistent and unpredictable, often due to transfer or purging. Liquid nitrogen is
often preferred to match the variable flow requirements.
periodic nitrogen consumption is predictable, but
not constant. A gas-generation plant backed up by liquid
nitrogen may be optimal.
Many plants exhibit a combination of usage patterns.

Closing thoughts
Nitrogen blanketing offers significant benefits in terms
of product quality and process safety, and when implemented properly, pays dividends in terms of efficiency,
effectiveness, and cost. Choosing the appropriate method
of nitrogen supply and nitrogen control system based on
the vessel design and the application can maximize the
desired safety and quality results while minimizing capital
CEP
and operating expenses.

Literature Cited
1. National Fire Protection Association, NFPA 69: Standard on
Explosion Prevention Systems, NFPA, Quincy, MA (2008).
2. Melhem, G. A., A Detailed Method for Estimating Mixture
Flammability Using Chemical Equilibrium, Process Safety
Progress, 16 (4), pp. 203218 (1997).
3. U.S. Chemical Safety and Hazard Investigation Board,
CSB Issues Final Report on Barton Solvents Explosion ,
www.csb.gov/newsroom/detail.aspx?nid=36, CSB, Washington,
DC (2008).
4. American Petroleum Institute, API 2000: Venting Atmospheric and Low-Pressure Storage Tanks, 6th ed., API, Washington, DC (2009).
5. International Organization for Standardization, ISO
28300:2008 Petroleum, Petrochemical and Natural Gas
Industries Venting of Atmospheric and Low-Pressure Storage
Tanks, ISO, Geneva (2008).

Paul Yanisko is the Process Industries Segment Leader in the International Commercial Technology Group at Air Products (7201 Hamilton
Blvd., Allentown, PA 18195-1501; Phone: (610) 481-8728; Fax: (610)
481-5431; Email: [email protected]), where he is responsible
for delivering industrial-gas-related solutions to customers in various industries, including the refinery, petrochemical, chemical, and
pharmaceutical sectors. His main areas of focus are Asia and Latin
America. Yanisko holds BS and MS degrees in chemical engineering
from Lafayette College and the Univ. of Connecticut, respectively.
Shiying Zheng is a research associate at Air Products (7201 Hamilton
Blvd., Allentown, PA 18195-1501; Phone: (610) 481-3027; Fax: (610)
706-5704; Email: [email protected]). She has more than
14 years of industrial experience in technology R&D, inventing and
developing new materials for a broad range of applications that
include gas separation, personal care, digital printing, medical imaging, and electronic display. Her experience also includes evaluating
technologies and developing new opportunities for the gas separation, electronics, and performance-materials businesses. In addition,
she has extensive experience in patent law and is a registered patent
agent. Before joining Air Products, she was a research associate at
Eastman Kodak Co. The holder of an MS and a PhD in polymer science
from Cornell Univ., Zheng is an inventor or co-inventor on 38 U.S.
patents, and the author of seven peer-reviewed journal articles and
two book chapters.
Joe Dumoit is a regional sales manager for the VCI product line at Cashco,
Inc. (607 W. 15th St., Ellsworth, KS 67439; Phone: (785) 472-4461;
Fax: (785) 472-3539; Email: [email protected]). He began his career
in sales at Leeds & Northrup, followed by stints at Varec and at L &
J Technologies. After several years, he moved to Durlam Associates,
where he sold Cashcos Valve Concepts line; he became a co-owner
of the firm in 1988 and continued to work in sales until the company
was sold in 2000. He was then hired by Cashco as a regional sales
manager and has continued selling and developing the VCI product
line. Dumoit holds a BS degree in electrical engineering from the Univ.
of Houston.
Bill Carlson is the product line manager of the Ntron gas analysis division of Neutronics Inc. (456 Creamery Way, Exton, PA 19341; Phone:
(610) 524-8800 x147; Fax: (610) 524-8807; Email: bill.carlson@
neutronicsinc.com). He has dedicated the majority of his 21-year
tenure to the design and development of oxygen-based Ntron ICS
inert gas control systems for the pharmaceutical, chemical, and paint
and coatings industries. He is a member of the International Society
of Automation (ISA).

CEP November 2011 www.aiche.org/cep

55