Scribd
Upload
56 views

RFR D H - Am-H RK: Eceiver Ecoder Ybrid I

data

Uploaded by

ΠΑΝΑΓΙΩΤΗΣΠΑΝΑΓΟΣ
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
56 views

RFR D H - Am-H RK: Eceiver Ecoder Ybrid I

data

Uploaded by

ΠΑΝΑΓΙΩΤΗΣΠΑΝΑΓΟΣ
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

RF RECEIVER DECODER HYBRID.

AM-HIRK

Features
Miniature RF Rx/Decoder System.
Superhet Rx with Keeloq Decoding
Advanced Laser Trimmed Hybrid
Range up to 100 Metres
Easy Learn Transmitter Feature.
CMOS/TTL Outputs, Momentary or Latching.
Direct Led Drive Data Reception
Single Supply 5V
Low Power Consumption
EMC Compliant for use in Europe
FCC Certified for use in USA

Applications
General Remote Control Systems.
Garage Door Openers.
Car, Caravan, Motorcycle Alarms

Remote Switching.
Remote Gates.
Paging.

Description
This miniature single in line (SIL) hybrid module is a complete three channel Radio Receiver/Decoder. When
used with the AM-110 series pocket keyfobs a complete remote telemetry system is obtained with upto
80metres range.
The module consists of a front end Super-Heterodyne RF receiver with an embedded microcontroller
decoding a highly secure Keeloq protocol signal.
The module has an easy-to-use 'LEARN' facility, and is capable of learning up to 50 unique keyfob encoders.
The module requires a 5V power supply, and provides a data reception direct LED drive and three digital data
outputs. The outputs may be programmed for momentary or latching configuration.

Application Circuit

Data Outputs
1
Not Used
3
2

AM-HiRX
1

11 13

16 18

Vcc

25

Data Reception
& Learn LED

Vcc
GND

DS097-5

Link 1 & 2

Feb 02

2002 REG No 277 4001, England.

Program Switch
(PSW)

Page 1

RF RECEIVER DECODER HYBRID.

AM-HIRK

Pin Descriptions
Pin No

Name

Description

Vcc-RF

+5V Supply Voltage

GND-RF

RF Ground

ANT

GND-RF

RF Ground

11

GND-AF

AF Ground

13

TP

Test Point

14

O/P-AF

Data output from RF receiver (CMOS/TTL signal)

15

Vcc-AF

+5V Supply Voltage

16

GND-AF

AF Ground

18

Link2

Connect to GND to make Link, may be left O/C if not required

19

Link1

Connect to GND to make Link, may be left O/C if not required

20

PSW

21

LED

22

O/P2

Programming Switch input, This is used when learning new transmitters.


External LED sink output, can be connected directly to cathode of external LED.
Connect Anode of the LED to +5V.
Indicates Data reception, and programming status.
Active High data Output 2 (has a 220 series resistor)

23

O/P3

Active High data Output 3 (has a 220 series resistor)

24

O/P4

Not Used

25

O/P1

Active High data Output 1 (has a 220 series resistor)

Connect Antenna to this input

Mechanical Details

63.5mm

14.5mm

12 3

See detail 'A'

11 13

18

25

Pins are on 0.1" Pitch


1.0mm

Detail 'A'

DS097-5

Feb 02

2002 REG No 277 4001, England.

Page 2

RF RECEIVER DECODER HYBRID.

AM-HIRK

Learning a New Transmitter Encoder


1. Briefly press the programming switch (PSW).
2. Learn LED will illuminate.
3. Depress the transmitter once, Learn LED will extinguish.
4. Depress the transmitter again, Learn LED will flash. (approx 10secs).
5. Wait for Learn LED to stop flashing.
6. This transmitter will now operate the system.
Erasing The HiRK Memory
1. Press and hold PSW , Learn LED will illuminate for approximately 10 seconds while the HiRK erases
its memory.
2. When Learn LED has turned off release PSW
3. Memory is now erased
Antenna Design
For 99% of applications a 17cm piece of wire is quite adequate. The range achieved from the system is
dependent on the choice and position of the antenna. The space around the antenna is as important as
the antenna itself. The optimum position is to locate the antenna so that is protrudes directly out the top of
the transmitter box. If this is not possible due to other design constraints, try to keep the antenna away
from other metal in the system such as transformers, batteries and PCB tracks, especially ground planes.
In particular, the HOT end of the antenna should be kept as far away as possible from these.
For further information on Antenna design please see our full product catalogue.
Data Outputs
Outputs 1,2, & 3 are digital CMOS/TTL (PIC Micro) with a series 220 protection resistor.
Outputs are all normally Low, active high.
Link Status
Link1
Open
Open
Connected
Connected

1 Switch Keyfob
2 Switch Keyfob
3 Switch Keyfob

DS097-5

Feb 02

Link2
Open
Connected
Open
Connected

Transmitter Switch
1
2
3
O/P 1
O/P 2
O/P 3
LATCH
LATCH
LATCH
MOM
MOM
MOM
MOM
MOM
LATCH
LATCH
LATCH
MOM

Transmitter Encoder Switch


O/P 1
O/P 2
Centre Switch
LH Switch
RH Switch
LH Switch
RH Switch

2002 REG No 277 4001, England.

O/P 3
Top Switch (Red)

Page 3

RF RECEIVER DECODER HYBRID.

AM-HIRK

Absolute Maximum Ratings


Supply Voltage (+5Vcc to GND)..........................................-0.3 to + 6 Volts.
o
Storage Temperature..........................................................-30 to +85 Celsius.
o
Operating Temperature....................................................... 0 to +70 Celsius.

Technical Specification
o

Ambient temperature = 25 Celsius.

Electrical Specification
Supply Voltage
Supply Current (quiescent)
Receiver Frequency
Receiver Frequency
Working Frequency

Min
4.5

Typical
5.0
6
315.0
433.92

450

Dimension
V
mA
MHz
MHz
MHz

20
+/- 400
-106
-70

-70

mSecs
KHz
dBm
dBm

0.2
3.8

0.8
5

V
V

200

(custom Frequencies Available)


Turn on Time

-3dB Bandwidth
R.F Sensitivity (100% AM)
Level of Emitted Spectrum
Data output: (any data output)
Logic Low
Logic High
Data output: (any data output)
Logic Low
Logic High
EMC Compliance

0
3.5

Max
5.5

Note

Please contact
Sales Dept

I out = 10mA
I out = 10mA

-25
mA
10
mA
Complies to ETS300-220

Part Numbering
PART No

DESCRIPTION

Compatible Transmitter encoder

Range**
(metres)

AM-HiRK-315

AM Superhet Rx Decoder

AM-110C1-315 (1 - 3 sw version)

50

AM-HiRK-433

AM Superhet Rx Decoder

AM-110C1-433 (1 - 3 sw version)

100

** Range quoted is optimum in line of sight without interference. In noisy built up areas this can be reduced
by over 50%
For more information or general enquiries, please call;
R. F. Solutions Ltd.,
Unit 21, Cliffe Industrial Estate,
South Street,
Lewes,
E Sussex, BN8 6JL. England.
Tel +44 (0)1273 898 000. Fax +44 (0)1273 480 661.
Email [email protected]
http://www.rfsolutions.co.uk
RF Solutions is a member of the Low Power Radio Association.

Information contained in this document is believed to be accurate , however no representation or warranty is given and no liability is assumed by R.F. Solutions Ltd. with respect to the accuracy of
such information. Use of R.F.Solutions as critical components in life support systems is not authorised except with express written approval from R.F.Solutions Ltd.

DS097-5

Feb 02

2002 REG No 277 4001, England.

Page 4

You might also like