Scribd Logo
Upload

Welcome to Scribd!

  • 1K views

    11-HONDA - Immobilizer Keys Setting

    Uploaded by

    Dario Gomez
    1) The document provides technical guidance on setting up an immobilizer system for a Honda vehicle. It explains that the immobilizer system prevents the vehicle from starting without the owner's ignition key. 2) It describes the process for registering ignition keys to the vehicle using an iSCAN-II device. This involves selecting the vehicle make and model, confirming all available keys are present, identifying the immobilizer type, and following on-screen instructions to turn keys on and off to synchronize them. 3) After all keys have been synchronized, turning the key off for 10 seconds completes the immobilizer key setting. The guidance emphasizes checking that all keys can now properly start the engine.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    11-HONDA - Immobilizer Keys Setting

    Uploaded by

    Dario Gomez
    1K views7 pages
    1) The document provides technical guidance on setting up an immobilizer system for a Honda vehicle. It explains that the immobilizer system prevents the vehicle from starting without the owner's ignition key. 2) It describes the process for registering ignition keys to the vehicle using an iSCAN-II device. This involves selecting the vehicle make and model, confirming all available keys are present, identifying the immobilizer type, and following on-screen instructions to turn keys on and off to synchronize them. 3) After all keys have been synchronized, turning the key off for 10 seconds completes the immobilizer key setting. The guidance emphasizes checking that all keys can now properly start the engine.

    Original Description:

    honda inmobilizador

    Original Title

    11-HONDA_Immobilizer Keys Setting

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    1) The document provides technical guidance on setting up an immobilizer system for a Honda vehicle. It explains that the immobilizer system prevents the vehicle from starting without the owner's ignition key. 2) It describes the process for registering ignition keys to the vehicle using an iSCAN-II device. This involves selecting the vehicle make and model, confirming all available keys are present, identifying the immobilizer type, and following on-screen instructions to turn keys on and off to synchronize them. 3) After all keys have been synchronized, turning the key off for 10 seconds completes the immobilizer key setting. The guidance emphasizes checking that all keys can now properly start the engine.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    1K views7 pages

    11-HONDA - Immobilizer Keys Setting

    Uploaded by

    Dario Gomez
    1) The document provides technical guidance on setting up an immobilizer system for a Honda vehicle. It explains that the immobilizer system prevents the vehicle from starting without the owner's ignition key. 2) It describes the process for registering ignition keys to the vehicle using an iSCAN-II device. This involves selecting the vehicle make and model, confirming all available keys are present, identifying the immobilizer type, and following on-screen instructions to turn keys on and off to synchronize them. 3) After all keys have been synchronized, turning the key off for 10 seconds completes the immobilizer key setting. The guidance emphasizes checking that all keys can now properly start the engine.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 7

    Software releases monthly for D91-EURO PRO YUP 2009 / D91-ASIAN PRO YUP 2009

    YUP customers, please get the updates from web site

    Technical Guidance

    HONDA: Immobilizer Keys Setting


    Introduction of Immobilizer System:
    The immobilizer system is designed to prevent the car from being started without the
    owners ignition key. If an attempt is made to start the car with any other key, the
    immobilizer system will disable the car fuel supply.
    Patterns of Immobilizer Indicator:
    1. Normal operation - If the immobilizer code is identified, the immobilizer indicator
    quickly flashes about 2 seconds when the ignition switch is turned ON (II). It is okay
    to start the engine.
    2. Immobilizer code is not identified - If the immobilizer code is not identified, the
    immobilizer indicator will quickly flash once, then will blink until the ignition switch
    is turned OFF. It is unable to start the engine.

    How does the Immobilizer System Work?


    With the ignition switch in ON (II) or START (III), the ECM/PCM sends power to ignition
    key transponder through the immobilizer control unit-receiver. The transponder then
    sends a coded signal back to the ECM/PCM through the receiver. If the signal is correct,
    the ECM/PCM will energize the cars fuel supply system by grounding the PGM-FI main
    relay.

    Before immobilizer keys setting, please make sure that all the available keys (registered
    or not) of this car are by your side. All keys should be synchronized each by each. Keys
    registration will clear all key entries if the procedure starts.
    The ignition key (built-in transponder) only controls the engine start or not. It is
    connection with shutting the cars fuel supply. It is unconcerned with the Body Central
    Locking System. About Remote alarm/Central Locking, please refer to the instruction of
    Vehicle Owners Manual.
    Preparatives:
    z

    If all the keys are lost, please buy 2 keys (built-in transponder). If there is an
    original key trace, please cut the keys first. If there is no original key trace, please
    replace a new lock and cut the new keys in advance.
    If there is one key available, please buy a new key (built-in transponder) and
    duplicate the key first.
    If the transponder of the key is malfunctioned, please buy the transponder. Use the
    small cross screwdriver to open the key case and replace the transponder.
    If the ECM/PCM or the immobilizer receiver unit is malfunctioned, please replace the
    unit first.

    Please make sure that the connection between ECM/PCM and immobilizer control
    unit-receiver is normal. The coil of the keyhole is intact. The connection between
    signal line and immobilizer control unit-receiver is normal.

    Steps on iSCAN-II:
    1. Select Vehicle Diagnostic select ASIAN

    MENU

    Vehicle Diagnostic

    1 Vehicle Diagnostic
    2 IMS2 (Interface Module
    Simulation System)
    10 OBD-II Standard Compliant
    iSCAN-II(V1.02)USEN
    20 SETUP

    1 ASIAN
    2 EUROPEAN

    2. Select JAPAN select HONDA software

    ASIAN

    JAPAN

    1 HONDA
    iSCAN-II (1.01SP2)USEN
    2 ACURA
    iSCAN-II (V1.01SP2)USEN
    3 NISSAN
    iSCAN-II(V1.03SP1)USEN
    4 INFINITI
    iSCAN-II (V1.03SP1)USEN

    1 [ JAPAN ]
    2 [ KOREA ]
    3 [ USA ]

    3. Select IMMOBILIZER KEYS SETTING

    System Selection
    1
    2
    3
    4
    5
    6

    PGM-FI
    A/T
    ABS/TCS/VSA
    SRS
    EPS
    IMMOBILIZER KEYS SETTING

    KEYS REGISTRATION

    Keys registration will clear all key


    entries. All keys should be
    registered
    if the procedure start.

    7 BODY
    8 IMA
    9 SMART KEY

    Press ENTER to next

    4. Make sure that all the available keys (registered or not) of this car are by your side.
    5. Turn ignition OFF.

    WARNING!

    WARNING!

    Please make sure all the keys


    (registered or not) are by your
    side.
    We need all the keys available for
    this car.
    Press ENTER to next,
    or Press EXIT to quit

    Please turn off the ignition.


    Press ENTER to start,
    or Press EXIT to quit

    5. Select the type. Select 5 SHOW TYPE DEFINITION to know which type of this car.

    10

    TYPE

    1
    2
    3
    4
    5

    TYPE 2A DEFINITION (1/3)

    ACURA CL (1999-2003)
    ACURA INTEGRA (2000-2001)
    ACURA TL (1999-2003)

    TYPE 2A
    TYPE 2B
    TYPE 2C
    TYPE 3
    SHOW TYPE DEFINITION

    Press EXIT to quit

    6. Press(right button) to see the next page.

    11

    12

    TYPE 2A DEFINITION (2/3)

    TYPE 2A DEFINITION (3/3)

    ACCORD (1998-2002)
    INSIGHT (2000-2006)
    ODYSSEY (1998-2002)

    S2000 (2000-2005)

    Press EXIT to quit

    Press EXIT to quit

    13

    14

    TYPE 2B DEFINITION (1/2)

    TYPE 2B DEFINITION (2/2)

    ACURA MDX (2001-2006)


    ODYSSEY (2003-2004)
    PILOT (2003-2005)

    S2000 (2004-2005)
    Press EXIT to quit

    Press EXIT to quit

    15

    16

    TYPE 2C DEFINITION (1/1)

    TYPE 3 DEFINITION (1/2)

    ACCORD (1998-2002)

    ACURA RSX (2002-2006)


    CIVIC (2001-2005)
    CRV (2002-2006)

    Press EXIT to quit

    Press EXIT to quit

    7. Make sure the type of this car and select the correct type.
    For example, CRV (2002-2006) is TYPE 3. Select 4 TYPE 3.

    17

    18

    TYPE 3 DEFINITION (2/2)

    TYPE

    ELEMENT (2003-2005)
    ODYSSEY (2003-2004)
    S2000 (2004-2005)

    1
    2
    3
    4
    5

    Press EXIT to quit

    TYPE 2A
    TYPE 2B
    TYPE 2C
    TYPE 3
    SHOW TYPE DEFINITION

    8. Enter TYPE 3 to continue, and follow the steps on screen to TURN KEY ON.

    19

    20

    KEY ON!

    Press Enter to continue


    Press Exit to quit

    !! TURN KEY ON !!

    9. Follow the steps on screen to TURN KEY OFF followe the steps on screen to
    TURN KEY ON

    21

    22

    KEY OFF!

    KEY ON!

    !! TURN KEY OFF !!

    !! TURN KEY ON !!

    10. After registration OK, please turn key OFF in 17 seconds.


    11. If there is another key, insert the next key in 17 seconds.
    Turn key ON, then turn key OFF.
    Repeat the steps ON and OFF if more keys.

    23

    24

    TURN KEY OFF!

    Start to sync.

    Registration OK. Please turn key OFF


    in 17 seconds.

    Insert the next key in 17 seconds,


    ON, the KEY OFF, and the next key.

    Press ENTER to continue

    If no more key exist, take the key


    out.

    12. After all the keys finished synchronization, TURN KEY OFF and wait for 10

    seconds.
    Immobilizer key setting is finished. Press any key to continue.

    25

    26

    TURN KEY OFF

    FINISHED

    TURN KEY OFF, and wait for 10


    seconds.

    FINISHED!

    Press any key to continue

    Press any key to continue

    13. Please insert the registered keys each by each to turn key ON and start
    the engine.
    Make sure that the synchronization of all the keys has been finished successfully.

    You might also like