Lecture 21-Robotics

Module 6 : Robot manipulators kinematics
Lecture 21 : Forward & inverse kinematics examples of 2R, 3R & 3P manipulators

Objectives
In this course you will learn the following
Inverse position and orientation matrix for 6R serial chain robot
Forward and inverse position problem for simple manipulators
Inverse Kinematics for 6R Manipulator using D-H Parameters

Here given the
joint position
for i=16 and the transformation matrix
EE position & orientation; Find out the
for i=1..6
Fig. 21.1 Concurrent wrist for PUMA robot

C is a point of concurrency is at distance
distance
from ref frame
Where equation (A) contains
from End Effector frame
with
as only unknowns.
& at
We observe that
does not exist when sin (arg) >1. This implies that end effecter is beyond the reach as
shown Figure 21.2. That is when sin (arg) is grater than 1, numerator is grater than denominator in
expression. And hence two solutions exist for
1.
Fig.21.2 Workspace for Puma
Figure 21.3 Work space for Puma Robot

(Hint for
)Use cosine rule knowing 3 sides, find angles; 2 solution for
Thus we have 2 solutions for

(refer figure 21.3). Now
&
each and therefore total 4 solutions for kinematics of Puma robot
will have COROSPONDING 4 solutions.
Part II
Here
is known in terms of
as given and thus RHS is known as
Thus all
for i=1.6 is known and problem of inverse kinematics for 6R Puma robot is solved.
Example of SCARA Manipulator

Basically it has RRP pairs as arm and single DOF as wrist. It is as shown in figure. The homogeneous
transformation matrices for
frame expressed in
frame is as follows
i.e. The D-H representation of linkage parameters are as given in table here.
Joint
ai
a1
a2
180
d3
d4
(Bold letters shows the joint variables)

The corresponding transformation matrices are
di
The forward kinematics problem will be knowing ai,

, di,
i.e. joint variables, finding end effector
position and orientation. This is achieved through above transformation matrices. The inverse position
problem would be, knowing the
elements in numerical values; finding the position and orientation of
each link i.e. ai,
solving for ai,
, di,
, di,
. This is achieved by equating numerical values of
to above
Fig. 21.2 SCARA Manipulator sketch of joint variables
Solve following
Exercise (A)
Do the Forward and inverse position calculation for concurrent wrist Manipulators
PUMA
Spherical
Cylindrical
SCARA
elements and
Do the exercise 1 calculation for non-concurrent wrist

Do the Exercise 1 for
Exercise (B)
Do the forward and inverse position calculation for serial chain manipulator / robot with n>6
[ Hint: In inverse kinematics, we have only EE position & orientation as known. This has 6 independent
variables as studied earlier. Therefore,
Infinite solution are possible for such chains and are kinematically redundant ]
Do the exercise for n<6
Generalised Stewart Platform is the one with fully parallel chain mechanism.
[ Hint: in forward kinematics, the local reference frame of all links are given & one has to find out the
position & orientation of the Stewart Platform. In Inverse kinematics it is the reverse way of above]
Hybrid links (combination of linear & rotary actuators ) can be solved for above depending on no. of links
in chains.
PUMA for non-concurrent wrist

We have C1(Xc1, Yc1, Zc1)0 and C2 (Xc2, Yc2, Zc2)0 as known points in terms of ref base ref frame and
ref frame (X3, Y3, Z3) and (X6, Y6, Z6) respectively(refer figure 21.4). (Both position and orientation as
follows).
Here the only unknowns are
in
Similarly,
Where the
wrist.
contains
as unknowns which can be solved as we have done for concurrent
Fig.21.4 PUMA non-concurrent wrist sketch

Cylindrical robot with 3 dof wrist ( non-concurrent C1 & C2)
Joint
ai
di
a1
d1
a2
d2
a3
d3
a4
d4
a5
d5
a6
d6
(Bold letters are the joint variables)

The procedure for obtaining
(refer figure 21.5) remains the same as for PUMA non
concurrent wrist with C1 & C2 as known.
Fig. 21.5 Sketch of cylindrical robot with joint variables

(All parameters listed in D-H table are not shown in figure)
Spherical robot with 3 dof wrist (non-concurrent C1 & C2)
Joint
ai
di
a1
d1
a2
d2
a3
d3
a4
d4
a5
d5
a6
d6
(Bold letters are the joint variables)
Fig.21.6 Sketch of spherical robot with joint variables (All parameters listed in
D-H table are not shown in figure)
The procedure for obtaining
(refer figure 21.6) remains the same as for PUMA non
concurrent wrist with C1 & C2 as known
Hybrid (3 DOF Stewart Platform) Manipulators

Forward Kinematics : Given the link parameters, find EE position & orientation.
The D-H table is given as
(Xp, Yp, Zp)
di
90
d2
Joint
ai
2
3
0
3
Fig. 21.7 Stewart Platform as 3 DOF hybrid manipulator

We have
as given earlier, hence the forward kinematics is multiplication of these transformation
matrices as
which gives position and orientation point P.
To get position of top platform, sum up three top joints coordinates. And to get orientation, take cross
product of orientation vectors from
.
Inverse kinematics: This will be as, given top platforms position and orientation, find out position and
orientation of each link. i.e. given numerical values of 4x4 matrix, finding the joint variables 1, d2, 3 is
a inverse kinematics problem. Equating and solving for joint variables is a solution.
Recap
In this course you will learn the following
Inverse position problem for PUMA robot.
Example of SCARA robot.
PUMA for non-concurrent wrist as example for forward kinematics.
Cylindrical robot with 3 dof wrist ( non-concurrent C1 & C2).
Example of Spherical robot with 3 DOF wrist (non-concurrent).
Example of Stewart platform as 3 DOF hybrid manipulator
Congratulations, you have finished Lecture 21. To view the next lecture select it from the left hand side
menu of the page.

Lecture 21-Robotics

Uploaded by

Copyright:

Available Formats

Lecture 21-Robotics

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lecture 21-Robotics

Uploaded by

Copyright:

Available Formats

Module 6 : Robot manipulators kinematics

Lecture 21 : Forward & inverse kinematics examples of 2R, 3R & 3P manipulators

Forward and inverse position problem for simple manipulators

Inverse Kinematics for 6R Manipulator using D-H Parameters

for i=16 and the transformation matrix

EE position & orientation; Find out the

Fig. 21.1 Concurrent wrist for PUMA robot

from ref frame

Where equation (A) contains

from End Effector frame

Fig.21.2 Workspace for Puma

Figure 21.3 Work space for Puma Robot

)Use cosine rule knowing 3 sides, find angles; 2 solution for

Thus we have 2 solutions for

each and therefore total 4 solutions for kinematics of Puma robot

will have COROSPONDING 4 solutions.

as given and thus RHS is known as

Example of SCARA Manipulator

(Bold letters shows the joint variables)

The forward kinematics problem will be knowing ai,

. This is achieved by equating numerical values of

Fig. 21.2 SCARA Manipulator sketch of joint variables

Do the exercise 1 calculation for non-concurrent wrist

PUMA for non-concurrent wrist

Here the only unknowns are

as unknowns which can be solved as we have done for concurrent

Fig.21.4 PUMA non-concurrent wrist sketch

(Bold letters are the joint variables)

(refer figure 21.5) remains the same as for PUMA non

concurrent wrist with C1 & C2 as known.

Fig. 21.5 Sketch of cylindrical robot with joint variables

(Bold letters are the joint variables)

(refer figure 21.6) remains the same as for PUMA non

concurrent wrist with C1 & C2 as known

Hybrid (3 DOF Stewart Platform) Manipulators

Fig. 21.7 Stewart Platform as 3 DOF hybrid manipulator

as given earlier, hence the forward kinematics is multiplication of these transformation

which gives position and orientation point P.

Example of SCARA robot.

PUMA for non-concurrent wrist as example for forward kinematics.

Cylindrical robot with 3 dof wrist ( non-concurrent C1 & C2).

Example of Spherical robot with 3 DOF wrist (non-concurrent).

Example of Stewart platform as 3 DOF hybrid manipulator

You might also like