Fire Stop

05/08
FirestopInternational 29.11.2006 9:22 Uhr Seite 1
CONTENT
Table of contents
General 3- 8
- Material properties / Advantages

- Processing
- International approvals
- Handling / Transport / Storage
Products 9-20
- Pipe / Socket
- Reducer / Elbow
- Tee / Cross
- Sprinkler outlet / End cap / Weld-in saddle
- Weldable flange adapter / Plastic flange /
Coupling screw joint
- Transition piece / Transition elbow
- Threaded branch tee / Transition joint
Transition piece for slot connection
- Weld-in saddle / Pipe cutter
- Welding device
- Welding accessories
- Welding tool / Drill
Fusion 21-32
- Part A:
Mounting of the tools
Heat-up phase
Handling
Guidelines
- Part B:
Checking of devices and tools
Preparation for the fusion
Heating of pipe and fittings
Setting and alignment
- Visual inspection of fusion seam
- Part C:
Weld-in saddles
Drilling, heat-up, joining, fixing
- Part D:
Welding machine
- Part E:
Repair
1
CONTENT
Table of contents
Laying of firestop pipes in the concrete 33-39
- Part 1:
Connecting of pipe work
to the sprinkler outlet
- Part 2:
Pressure test of pipe work installation
as strength test and leak test
- Part 3:
What must be considered
during the concreting process?
- Part 4:
Access to connection
of the pipe work in concrete
- Part 5:
Bridging of building joints
- Part 6:
Potential equalizing
- Part 7:
Pressurizing in the firestop-supply
during the concreting process
- Part 8:
Influence of the concrete
to the applied compounds
Test 40-43
- Leakage test / Pressure diagram

- Test record firestop system installation
- Form: “Enquiry for the chemical resistance“
References 44-50
aquatherm worldwide 51
Notes 52-54
2
GENERAL
aquatherm firestop-
sprinkler pipe system
aquatherm firestop offers an extensive range of pipes and fittings for
the installation of fire sprinkler systems.
The system is based on a fibre reinforced polypropylene pipe (faser

composite pipe) produced in a multi-layer extrusion process.
The material fusiolen® PP-R (80) FS, used for the production of these
pipes, is a plastic whose profile of properties is designed for the special
demands of the field of application. Both, the installer’s request for easier
processing and the demand for maximum safety in later application was
taken into account during its development.
aquatherm firestop is:
- connection by fusion welding

No sealants or adhesives are required for this permanent connection.
- corrosion-proof
Prevents the clogging of the sprinkler with corrosive products.
This ensures a long, low-maintenance service life as well as trouble-free
functioning of the system.
The production of pipes and fittings is controlled according to the highest

quality standards on latest injection moulding machines and extrusion
lines. The high quality of our products is also ensured by extensive controls
of incoming goods and the production process.
The aquatherm quality management system is certified according to

DIN EN ISO 9001:2000.
aquatherm firestop -
The advantages:
➟ certified and quality inspected
➟ connection by fusion welding
➟ resistant against corrosion and chemicals
no accumulation of corrosion products
➟ low pipe roughness factor and high abrasion resistance
➟ heat and sound-insulating characteristics
➟ high impact strength
➟ leakproof connection of pipe and
fitting by fusion technique
➟ not easily flammable acc. to din
4102-1, building material class B1
➟ low weight compared to metal pipes
➟ short processing time
➟ no gaskets - sealing elements are not required
➟ 3-layer pipe with fibre glass reinforced inner layer
3
GENERAL
Processing
Fusion technique
By the fusion of pipe and fitting the plastic melts to a homogeneous
material unit.
Pipe and fitting are heated quickly with specially provided welding tools
and joined together - finished!
Double material thickness at the joint – giving double safety at the

otherwise critical point of a pipe system.
A permanent leakproof connection is created with the aquatherm fusion

technique.
4
GENERAL
Processing
Weld-in saddle technique
Branches can easily be made by weld-in saddles, even post-installation.
Material costs and processing time are reduced by using weld-in saddles.
Whereas in case of tees three joints are to be processed, work is limited

to mounting the saddle and the branch pipe only.
Simply drill the pipe; heat up the saddle, pipe wall and surface; connect the
parts. Finished!
5
GENERAL
International approvals
for the application as sprinkler lines
Fire protection requirements

and standards for planning
and construction of sprinkler
systems vary locally.
Thus, the application of

Germany
firestop in any case has to be
For the pipe dimensions 25, 32, 40, agreed and coordinated with
50, 63, 75 mm (DN15 up to DN50)
and the corresponding fittings the local national fire protecti-
on authorities, the constructor
and the building insurers.
LPCB
684 a
Great Britain
(All pipe dimensions)
04-904
Sweden
Further certification either

national or local are in process.
Russia
Great Britain
V E LT E H
Croatia
New Zealand
AS 4118.2.1
Lic SMKP20464
Australia
6
GENERAL
Handling
Transport and storage
firestop-pipes can be stored in all outside temperatures. Pipes should be

stored and transported flat and fully supported along their length.
Bending pressures are to be avoided. High impact should be avoided at
externely low temperatures.
Although firestop-pipes are extremely robust, it is recommended to treat

the material always with care.
UV resistance
Pipes from fusiolen® PP-R (80) FS should not be installed (without protecti-
on) where subject to UV-radiation. All firestop-pipes and fittings are sup-
plied in UV-protected packaging to bridge transport and assembly time.
Ultraviolet rays have an influence on all high polymeric plastics. Hence,
pipes should not be stored unprotected outside for a long time. The maxi-
mum storage time is (outside) 6 months.
Fire bulkheading
All fire prevention systems which can prove equivalent licensing are suited
for the firestop pipe system. aquatherm recommends equivalent the
Rockwool Conlit fire retardant seals as an ideal fire prevention solution for
the fire-stop-pipe system.
Procedures for additional repair
Cut out damaged / leaking section and replace as for a new installation
or repair with pipe repair stick (page 32).
7
GENERAL
Handling
Chemical resistance
On account of the special material qualities firestop-pipes and fittings pro-

vide extensive chemical resistance. firestop-transition connections and ele-
ments with brass inserts are not suitable for all media. The compatibility
should be asked at aquatherm with media deviating from water. Please,
use the “Enquiry for the chemical resistance” in the appendix.
Pipe friction loss
The pressure loss caused by friction is to be calculated hydraulically with the

Hazen-Williams-formula.
The value to be used for C is 150, applicable for calculations of sprinkler

installations and water supply.
Equivalent lengths for the

aquatherm firestop
sprinkler pipe system
Pipe dimension
without
Nominal diameter DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80
class
25.0 32.0 40.0 50.0 63.0 75.0 90.0 110.0 125.0
Outer diameter firestop
mm mm mm mm mm mm mm mm mm
Article Equivalent pipe length in (m)
Socket 0.22 0.30 0.40 0.52 0.70 0.86 1.07 1.36 1.58
Reduction of 1dimension 0.27 0.37 0.48 0.63 0.83 1.03 1.28 1.63 1.90
Reduction of 2 dimensions 0.36 0.49 0.64 0.84 1.11 1.37 1.71 2.17 2.53
Elbow 90° 0.67 0.91 1.20 1.57 2.09 2.57 3.20 4.07 4.74
Elbow 45° 0.33 0.46 0.60 0.78 1.04 1.28 1.60 2.03 2.37
Standard tee or cross flow
0.98 1.34 1.76 2.30 3.06 3.76 4.70 5.96 6.96
direction branch
The equivalent lengths of transition pieces, threaded connexions and

tees (flow direction: straight) can be edequated with the socket values.
8
PRODUCTS
firestop-pipe SDR 7.4 / B1
Material : PP-R (80) FS

Pipe series : SDR 7.4
Packing unit : straight lengths á 4 m
Colour : red / 4 green stripes
di
d
s
Wall Internal Water

Pipe Diameter
content
Weigth
thickness diameter
d s di
Art.-No. Dimension PU l/m kg/m DN
mm mm mm
4170708 20 mm 100 20 2.8 14.4 0.163 0.152 10
4170710 25 mm 100 25 3.5 18.0 0.254 0.236 15
4170712 32 mm 40 32 4.4 23.2 0.423 0.379 20
4170714 40 mm 40 40 5.5 29.0 0.661 0.590 25
4170716 50 mm 20 50 6.9 36.2 1.029 0.919 32
4170718 63 mm 20 63 8.6 45.8 1.647 1.444 40
4170720 75 mm 20 75 10.3 54.4 2.324 2.054 50
4170722 90 mm 12 90 12.3 65.4 3.359 2.943 65
4170724 110 mm 8 110 15.1 79.8 5.001 4.403 80
4170726 125 mm 4 125 17.1 90.8 6.475 5.669 90
firestop-socket / B1
Packing Price/ Product-
Art.-No. Dimension unit Piece Price Piece group
4111008 20 mm 10 pc 1 42
4111010 25 mm 10 pc 1 42
4111012 32 mm 5 pc 1 42
4111014 40 mm 5 pc 1 42
4111016 50 mm 5 pc 1 42
4111018 63 mm 1 pc 1 42
4111020 75 mm 1 pc 1 42
4111022 90 mm 1 pc 1 42
4111024 110 mm 1 pc 1 42
4111026 125 mm 1 pc 1 42
9
PRODUCTS
firestop-reducer / B1
4111112 25 / 20 mm 10 pc 1 42
4111116 32 / 25 mm 5 pc 1 42
4111122 40 / 32 mm 5 pc 1 42
4111124 50 / 20 mm 5 pc 1 42
4111128 50 / 32 mm 5 pc 1 42
4111130 50 / 40 mm 5 pc 1 42
4111131 63 / 20 mm 1 pc 1 42
4111138 63 / 50 mm 1 pc 1 42
4111142 75 / 63 mm 1 pc 1 42
4111152 90 / 63 mm 1 pc 1 42
4111153 90 / 75 mm 1 pc 1 42
4111155 110 / 63 mm 1 pc 1 42
4111159 110 / 90 mm 1 pc 1 42
4111163 125 / 90 mm 1 pc 1 42
4111165 125 / 110 mm 1 pc 1 42
firestop-reducing socket / B1
Art.-No. Dimension Price Piece group
unit Piece
4111238 63/50 mm 1 pc 1 42
4111242 75/63 mm 1 pc 1 42
4111253 90/75 mm 1 pc 1 42
firestop-elbow 90° / B1
Art.-No. Dimension Packing Price/ Product-
Price Piece group
unit Piece
4112108 20 mm 10 pc 1 42
4112110 25 mm 10 pc 1 42
4112112 32 mm 5 pc 1 42
4112114 40 mm 5 pc 1 42
4112116 50 mm 5 pc 1 42
4112118 63 mm 1 pc 1 42
4112120 75 mm 1 pc 1 42
4112122 90 mm 1 pc 1 42
4112124 110 mm 1 pc 1 42
4112126 125 mm 1 pc 1 42
firestop-elbow 90º / B1 female / male

Art.-No. Dimension Piece Price Piece group
unit
4112308 20 mm f/m 10 pc 1 42
4112310 25 mm f/m 10 pc 1 42
4112312 32 mm f/m 5 pc 1 42
4112314 40 mm f/m 5 pc 1 42
10
PRODUCTS
firestop-elbow 45 ° / B1
unit Piece
4112508 20 mm 10 pc 1 42
4112510 25 mm 10 pc 1 42
4112512 32 mm 5 pc 1 42
4112514 40 mm 5 pc 1 42
4112516 50 mm 5 pc 1 42
4112518 63 mm 1 pc 1 42
4112520 75 mm 1 pc 1 42
4112522 90 mm 1 pc 1 42
4112524 110 mm 1 pc 1 42
4112526 125 mm 1 pc 1 42
firestop-elbow 45° / B1 female / male

unit
4112708 20 mm f/m 10 pc 1 42
4112710 25 mm f/m 10 pc 1 42
4112712 32 mm f/m 5 pc 1 42
4112714 40 mm f/m 5 pc 1 42
firestop-tee / B1
Price Piece group
unit Piece
4113108 20 mm 10 pc 1 42
4113110 25 mm 10 pc 1 42
4113112 32 mm 5 pc 1 42
4113114 40 mm 5 pc 1 42
4113116 50 mm 5 pc 1 42
4113118 63 mm 1 pc 1 42
4113120 75 mm 1 pc 1 42
4113122 90 mm 1 pc 1 42
4113124 110 mm 1 pc 1 42
4113126 125 mm 1 pc 1 42
firestop-reducing tee / B1
Art.-No. Dimension unit Price Piece group
Piece
4113511 20 x 25 x 20 mm 10 pc 1 42
4113520 25 x 20 x 20 mm 10 pc 1 42
4113522 25 x 20 x 25 mm 10 pc 1 42
4113532 32 x 20 x 20 mm 5 pc 1 42
4113534 32 x 20 x 32 mm 5 pc 1 42
4113540 32 x 25 x 32 mm 5 pc 1 42
4113546 40 x 32 x 40 mm 5 pc 1 42
4113550 50 x 32 x 50 mm 5 pc 1 42
4113551 50 x 40 x 50 mm 5 pc 1 42
4113558 63 x 40 x 63 mm 1 pc 1 42
4113560 63 x 50 x 63 mm 1 pc 1 42
4113568 75 x 50 x 75 mm 1 pc 1 42
11
PRODUCTS
firestop-reducing tee / B1
Art.-No. Dimension unit Price Piece group
Piece
4113570 75 x 63 x 75 mm 1 pc 1 42
4113580 90 x 50 x 90 mm 1 pc 1 42
4113582 90 x 63 x 90 mm 1 pc 1 42
4113584 90 x 75 x 90 mm 1 pc 1 42
4113586 110 x 63 x 110 mm 1 pc 1 42
4113588 110 x 75 x 110 mm 1 pc 1 42
4113590 110 x 90 x 110 mm 1 pc 1 42
4113592 125 x 75 x 125 mm 1 pc 1 42
4113594 125 x 90 x 125 mm 1 pc 1 42
4113596 125 x 110 x 125 mm 1 pc 1 42
firestop-cross / B1
unit Piece
4113712 32 mm 5 pc 1 42
4113714 40 mm 5 pc 1 42
firestop-reducing cross / B1
unit Piece
4113750 50/32 mm 1 pc 1 42
4113756 63/32 mm 1 pc 1 42
4113764 75/32 mm 1 pc 1 42
firestop-end cap / B1
unit Piece
4114108 20 mm 10 pc 1 42
4114110 25 mm 10 pc 1 42
4114112 32 mm 5 pc 1 42
4114114 40 mm 5 pc 1 42
4114116 50 mm 5 pc 1 42
4114118 63 mm 1 pc 1 42
4114120 75 mm 1 pc 1 42
4114122 90 mm 1 pc 1 42
4114124 110 mm 1 pc 1 42
4114126 125 mm 1 pc 1 42
12
PRODUCTS
firestop-base part for sprinkler outlet

Packing Price/ Product
Art.-No. Dimension Piece Price Piece
unit group
4114180 - 25 pc 1 42
firestop-upper part for sprinkler outlet

unit group
4114181 1/2” 25 pc 1 42
4114182 3/4” 25 pc 1 42
4114183 1” 25 pc 1 42
firestop-plug for sprinkler outlet

unit group
4114185 1 /2 ” 25 pc 1 42
4114186 3 /4 ” 25 pc 1 42
4114187 1” 25 pc 1 42
firestop-weld-in saddle / B1
unit Piece
4115156 40/20 mm 5 pc 1 42
4115158 40/25 mm 5 pc 1 42
4115160 50/20 mm 5 pc 1 42
4115162 50/25 mm 5 pc 1 42
4115164 63/20 mm 5 pc 1 42
4115166 63/25 mm 5 pc 1 42
4115168 63/32 mm 5 pc 1 42
4115170 75/20 mm 5 pc 1 42
With weld-on surface and
4115172 75/25 mm 5 pc 1 42 weld-in socket to be fused with
4115174 75/32 mm 5 pc 1 42 the inner wall of the pipe.
4115175 75/40 mm 5 pc 1 42
4115176 90/20 mm 5 pc 1 42 The required tools for the
fusion of firestop-weld-in
4115178 90/25 mm 5 pc 1 42
saddles are listed on page 21:
4115180 90/32 mm 5 pc 1 42
4115181 90/40 mm 5 pc 1 42 ➟ weld-in saddle tools
4115182 110/20 mm 5 pc 1 42 Art.-No. 50614 - 50644
4115184 110/25 mm 5 pc 1 42
4115186 110/32 mm 5 pc 1 42 ➟ fusiotherm®-drill
4115188 110/40 mm 5 pc 1 42
Art.-No. 50940 - 50948
4115189 110/50 mm 5 pc 1 42
4115190 125/20 mm 5 pc 1 42
4115192 125/25 mm 5 pc 1 42
4115194 125/32 mm 5 pc 1 42
4115196 125/40 mm 5 pc 1 42
4115197 125/50 mm 5 pc 1 42
4115198 125/63 mm 5 pc 1 42
13
PRODUCTS
firestop-weldable flange adapter / B1

with joint ring

Price Piece group
unit Piece
4115512 32 mm 1 pc 1 42
4115514 40 mm 1 pc 1 42
4115516 50 mm 1 pc 1 42
4115518 63 mm 1 pc 1 42
4115520 75 mm 1 pc 1 42
4115522 90 mm 1 pc 1 42
4115524 110 mm 1 pc 1 42
4115527 125 mm 1 pc 1 42
firestop-steel flange / B1
for socket
Art.-No. welded no.of hole Packing Price/ Price/ Piece Product-
type nipples holes circle Unit Piece Price
Euro group
15712 32 mm 4 85 mm 1 pc 1 42
15714 40 mm 4 100 mm 1 pc 1 42
15716 50 mm 4 110 mm 1 pc 1 42
15718 63 mm 4 125 mm 1 pc 1 42
15720 75 mm 4 145 mm 1 pc 1 42
15722 90 mm 8 160 mm 1 pc 1 42
15724 110 mm 8 180 mm 1 pc 1 42
15726 125 mm 8 210 mm 1 pc 1 42
firestop-coupling screw / B1
unit Piece
4115812 32 mm 1 pc 1 42
4115814 40 mm 1 pc 1 42
4115816 50 mm 1 pc 1 42
4115818 63 mm 1 pc 1 42
4115820 75 mm 1 pc 1 42
Incl. 2 flange adapters with gasket
firestop-back plate elbow / B1

unit Piece
4120108 20 x 1/2” f 10 pc 1 42
4120112 25 x 3 /4 ” f 10 pc 1 42
firestop-transition piece / B1 round

4121008 20 x 1/2” f 10 pc 1 42
4121011 25 x 1 /2 ” f 10 pc 1 42
4121013 32 x 3 /4 ” f 10 pc 1 42
14
PRODUCTS
firestop-transition piece, female / B1

with hexagon
Packing Price/
Price/ Product-
Art.-No. Dimension
Dimension Piece Price Piece
Piece
unit Piece group
4121108 20 mm x 1/2” f 10 pc 1 42
3
4121110 20 mm x /4” f 10 pc 1 42
4121111 25 mm x 1/2” f 10 pc 1 42
3
4121112 25 mm x /4” f 10 pc 1 42
4121113 32 mm x 3/4” f 5 pc 1 42
4121114 32 mm x 1” f 5 pc 1 42
4121115 40 mm x 1” f 5 pc 1 42
1
4121116 40 mm x 1 /4” f 5 pc 1 42
1
4121117 50 mm x 1 /4” f 5 pc 1 42
4121118 50 mm x 11/2” f 5 pc 1 42
1
4121119 63 mm x 1 /2” f 1 pc 1 42
4121120 63 mm x 2” f 1 pc 1 42
4121122 75 mm x 2” f 1 pc 1 42
4121153 32 mm x 1/2” f 1 pc 1 42
4121154 40 mm x 1/2” f 1 pc 1 42
firestop-transition piece / B1 with hexagon

4121308 20 x 1/2” m 10 pc 1 42
4121310 20 x 3/4” m 10 pc 1 42
1
4121311 25 x /2” m 10 pc 1 42
4121312 25 x 3/4” m 10 pc 1 42
3
4121313 32 x /4” m 10 pc 1 42
4121314 32 x 1” m 5 pc 1 42
1
4121316 32 x 1 /4” m 5 pc 1 42
4121317 40 x 1” m 5 pc 1 42
4121318 40 x 11/4” m 5 pc 1 42
4121319 50 x 11/4” m 5 pc 1 42
4121320 50 x 11/2” m 5 pc 1 42
1
4121321 63 x 1 /2” m 1 pc 1 42
4121322 63 x 2” m 1 pc 1 42
4121323 75 x 2” m 1 pc 1 42
4121324 75 x 21/2” m 1 pc 1 42
4121325 90 x 3” m 1 pc 1 42
4121327 110 x 4” m 1 pc 1 42
firestop-transition elbow / B1
unit Piece
4123008 20 x 3/4” f 10 pc 1 42
1
4123010 20 x /2” f 10 pc 1 42
4123012 25 x 3/4” f 10 pc 1 42
1
4123014 25 x /2” f 10 pc 1 42
4123015 32 x 1/2” f 5 pc 1 42
3
4123016 32 x /4” f 5 pc 1 42
4123018 32 x 1” f 5 pc 1 42
4123020 40 x 1/2” f 5 pc 1 42
15
PRODUCTS
firestop-threaded branch tee / B1

unit Piece
4125006 20 x 1/2” f x 20 10 pc 1 42
3
4125008 20 x /4” f x 20 10 pc 1 42
4125010 25 x 1/2” f x 25 10 pc 1 42
3
4125012 25 x /4” f x 25 10 pc 1 42
4125013 32 x 1/2” f x 32 5 pc 1 42
3
4125014 32 x /4” f x 32 5 pc 1 42
4125016 32 x 1” f x 32 5 pc 1 42
1
4125018 40 x /2” f x 40 5 pc 1 42
4125022 50 x 1” x 50 5 pc 1 42
4125024 50 x 11/4” f x 50 5 pc 1 42
firestop-threaded connection union/ B1

Length: 100 mm threaded, with gasket

Price Piece group
unit Piece
4126708 20 mm/nut R 1” 1 pc 1 42
1
4126710 25 mm/nut R 1 /4” 1 pc 1 42
4126712 32 mm/nut R 11/2” 1 pc 1 42
4126714 40 mm/nut R 2” 1 pc 1 42
1
4126716 50 mm/nut R 2 /4” 1 pc 1 42
4126718 63 mm/nut R 23/4” 1 pc 1 42
1
4126720 75 mm/nut R 3 /2” 1 pc 1 42
4126722 90 mm/nut R 4” 1 pc 1 42
firestop-female part union / B1

ISO-Standard

unit Piece
4127010 nut R 1”x20 mm 5 pc 1 42
1
4127012 nut R 1 /4”x25 mm 5 pc 1 42
4127014 nut R 11/2”x32 mm 5 pc 1 42
4127016 nut R 2”x40 mm 5 pc 1 42
4127018 nut R 21/4”x50 mm 5 pc 1 42
3
4127020 nut R 2 /4”x63 mm 1 pc 1 42
4127022 nut R 31/2”x75 mm 1 pc 1 42
firestop-counterpart/ B1
with welding socket and male thread for ISO-threaded joints

4127310 20 mm x 1” m 10 pc 1 42
1
4127312 25 mm x 1 /4” m 10 pc 1 42
4127314 32 mm x 11/2” m 5 pc 1 42
4127316 40 mm x 2” m 5 pc 1 42
1
4127318 50 mm x 2 /4” m 5 pc 1 42
4127320 63 mm x 23/4” m 1 pc 1 42
1 firestop-metal composite fittings are manufactu-
4127322 75 mm x 3 /2” m 1 pc 1 42
red from fusiolen® PP-R (80) FS and brass.
16
PRODUCTS
firestop-transition piece for groove connection

4127054 40 mm / 1" 5 pc 1 42
4127056 50 mm / 11/4" 5 pc 1 42
4127058 63 mm / 11/2" 1 pc 1 42
4127060 75 mm / 2" 1 pc 1 42
firestop-weld-in saddle / B1
with female thread and hexagon socket, with weld-in weld-on surface and weld-in socket
to be fused with the inner wall of the pipe

Price Piece group
unit Piece
4128214 40/25 x 1/2” f 5 pc 1 42

4128216 50/25 x 1/2” f 5 pc 1 42
1
4128218 63/25 x /2” f 5 pc 1 42
4128220 75/25 x 1/2” f 5 pc 1 42
1
4128222 90/25 x /2” f 5 pc 1 42
4128224 110/25 x 1/2” f 5 pc 1 42 The required tools for the
4128226 1
125/25 x /2” f 5 pc 1 42 fusion of firestop-weld-in
4128234 40/25 x 3/4” f 5 pc 1 42 saddles are listed on page 21:
4128236 50/25 x 3/4” f 5 pc 1 42
3
➟ weld-in saddle tools
4128238 63/25 x /4” f 5 pc 1 42
Art.-No. 50614 - 50644
4128240 75/25 x 3/4” f 5 pc 1 42
4128242 3
90/25 x /4” f 5 pc 1 42 ➟ fusiotherm®-drill
4128244 110/25 x 3/4” f 5 pc 1 42 Art.-No. 50940 - 50948
3
4128246 125/25 x /4” f 5 pc 1 42
4128260 75/32 x 1” f 5 pc 1 42
4128262 90/32 x 1” f 5 pc 1 42
4128264 110/32 x 1” f 5 pc 1 42
4128266 125/32 x 1” f 5 pc 1 42
firestop-ball valve
Packing
Liefer- Price/
Preis/ Preis Product-
Produkt-
Art.-No.
Art.-Nr. Dimension
Abmessung Price Piece
Stück group
unit
einheit Piece
Stück Euro gruppe
4141308 20 mm 1 pc 1 42
4141310 25 mm 1 pc 1 42
4141312 32 mm 1 pc 1 42
4141314 40 mm 1 pc 1 42
4141316 50 mm 1 pc 1 42
4141318 63 mm 1 pc 1 42
firestop-pipe repair stick

unit
4160600 7/11 mm 10 pc 1 42
Material: fusiolen® PP-R (80) FS to close pipe holes up to 10

mm.Tool: fusiotherm® -repair kit (Art.-No. 50307 + 50311).
firestop-metal composite fittings are manufactured from fusiolen® PP-R (80) FS and brass.
17
PRODUCTS
fusiotherm®-pipe cutter
unit
50102 16 - 40 mm 1 pc 1 3
50105 50 - 125 mm 1 pc 1 3
fusiotherm®-pipe cutter
unit
50104 16 - 40 mm 1 pc 1 3
fusiotherm®-manual welding device (500 W)

fusiotherm

unit group
aquatherm
50336 for pipe-Ø 16-32 mm 1 pc 1 3
With base and case for tools

fusiotherm

unit
aquatherm
50337 for pipe-Ø 16-63 mm 1 pc 1 3


Packing Price/ Product- fusiotherm

unit
50341 for pipe-Ø 50-125 mm 1 pc 1 3
aquatherm
18
PRODUCTS
fusiotherm®-welding machine (1400 W)

unit
50147 for pipe-Ø 50-125 mm 1 pc 1 3
Incl. welding tools 50-125 mm (Art.-No.: 50216-50226)

fusiotherm®-manual welding device (1400 W) and wooden transport case
aquatherm
fusiotherm®-electric welding jig
unit Piece
50149 for pipe-Ø 63-125mm 1 pc 1 3
incl. spare battery, charging station and metal case Support: Art.-No. 50151 on request aquath
erm
fusiotherm®-thermocolour pencil
unit
50190 - 1 pc 1 3
For check-up of the correct welding temperature
fusiotherm®-welding tool
unit group
50208 20 mm 1 pc 1 3
50210 25 mm 1 pc 1 3
50212 32 mm 1 pc 1 3
50214 40 mm 1 pc 1 3
50216 50 mm 1 pc 1 3
50218 63 mm 1 pc 1 3
50220 75 mm 1 pc 1 3
50222 90 mm 1 pc 1 3
50224 110 mm 1 pc 1 3
50226 125 mm 1 pc 1 3
19
PRODUCTS
fusiotherm®-repair kit
to close pipe holes up to 10 mm (pipe repair stick Art.-No. 60600)
Art.-No. Packing Price/ Piece Product-

Dimension unit Piece Price group
50307 7 mm 1 pc 1 3
50311 11 mm 1 pc 1 3
fusiotherm®-welding tool 50619
for welding saddles of art.-no. 4115156-4115198 and 4128214-4128266

unit group
50614 40/20 + 25 mm 1 pc 1 3
50616 50/20 + 25 mm 1 pc 1 3
50619 63/20 + 25 mm 1 pc 1 3
50620 63/32 mm 1 pc 1 3
50623 75/20 + 25 mm 1 pc 1 3
50624 75/32 mm 1 pc 1 3
50625 75/40 mm 1 pc 1 3
50627 90/20 + 25 mm 1 pc 1 3
50628 90/32 mm 1 pc 1 3
50629 90/40 mm 1 pc 1 3
50631 110/20 + 25 mm 1 pc 1 3
50632 110/32 mm 1 pc 1 3
50634 110/40 mm 1 pc 1 3
50635 110/50 mm 1 pc 1 3
50636 125/20 + 25 mm 1 pc 1 3
50638 125/32 mm 1 pc 1 3
50640 125/40 mm 1 pc 1 3
50642 125/50 mm 1 pc 1 3
50644 125/63 mm 1 pc 1 3
fusiotherm®-drill
for the mounting of weld-in saddles

50940 20+25 mm 1 pc 1 3
50942 32 mm 1 pc 1 3
50944 40 mm 1 pc 1 3
50946 50 mm 1 pc 1 3
50948 63 mm 1 pc 1 3
20
TECHNIQUE
Part A:
Mounting of the welding tools
1. Important!
Only use original fusiotherm®-welding devices and fusiotherm®-welding

tools.
2. Assemble and tighten the cold welding tools manually.
3. All welding tools must be free from impurities. Check, if they are clean
before assembling. If necessary clean the welding tools with a non
fibrous, coarse tissue and with spirit.
4. Place the welding tools, so that there is full surface contact between the
welding tool and the welding plate. Welding tools over Ø 40 mm must
always be fitted to the rear position of the welding plate.
5. Plug in the welding device and check, if operating lamp is on. Depending
on the ambient temperature it takes 10-30 minutes to heat-up the
welding plate.
The heat-up phase ends, when the temperature pilot lamp blinks and
a signal is audible.
RIGHT WRONG
Electric power supply:

The power supply must coincide with the data on the type plate of the welding
device and must be protected according to the local regulations. To avoide high
power loss, the conductor cross-section of the used extension cables must be
selected according to the power input of the welding devices.
21
TECHNIQUE
Part A:
Heat-up phase
6. During the heat-up phase tighten the welding tools carefully with the
Allen Key. Take care that the tools fully contact the welding plate.
Never use pliers or any other unsuitable tools, as this will damage the
coating of the welding tools.
7. The required temperature to weld the firestop-system is 260 °C.

Acc. to DVS-Welding Guidelines the temperature of the welding device
has to be checked at its tool before starting the welding process. This
has to be done with a fast indicating thermometer or alternatively with
a fusiotherm®-thermocolour crayon. (see “Fusion part B, item 2”)
ATTENTION:
First welding at the earliest 10 minutes after reaching the
welding temperature. DVS 2207, Part 11.
Heating plate
Temperature
pilot lamp (orange) Welding
tool
Operating lamp (green)
Welding tool
Part A:
Handling
8. A tool change on a heated device requires another check of the
welding temperature at the new tool (after heat-up phase).
9. If the device has been unplugged, i. e. during longer breaks, the

heat-up process has to be restarted (from item 5).
10. After use unplug the welding device and cool down. Water must
never be used to cool the welding device, as this would destroy the
heating resistances.
22
TECHNIQUE
Part A:
Handling
11. Protect fusiotherm®-welding devices and tools against impurities.
Burnt-it particles may result in an incorrect fusion. The tools may be
cleaned with fusiotherm®-cleaning wipes, Art.-No. 50193. Always keep
the burnt-in welding tools dry. If necessary, dry them with a clean, non
fibrous tissue.
12. For perfect fusion, damaged or dirty welding tools must be replaced, as
only undamaged tools ensure a perfect fusion welding.
13. Never attempt to open or repair a defective device. Return the defective
device for repair.
14.Check the operating temperature of the fusiotherm®- welding devices

regularly by means of suitable measuring instruments.
Part A:
Guidelines
15. For the correct handling of welding machines the following must be
observed:
General Regulations for Protection of Labour and Prevention of

Accidents
and particularly
the Regulations of the Employers’ Liability Insurance Association of the

Chemical Industry regarding Machines for the Processing of Plastics,
chapter: "Welding Machines and Welding Equipment".
16.For the handling of the fusiotherm®-welding machines, devices and

tools please observe
General Regulations DVS 2208 Part 1 of the German Association for

Welding Engineering, Registered Society (Deutscher Verband für Schweiß-
technik e. V.).
23
TECHNIQUE
Part B:
Checking of devices and tools
1. Check, if the fusiotherm®-welding device and tool correspond to the
guidelines “Fusion Part A”.
2. All devices and tools in use must have reached the required operating
temperature of 260° C in use. This needs a separate, compulsory test,
acc. to DVS-Welding Guideline "Fusion Part A, item 8". The control of
the operating temperature can be made with fast indicating thermo-
meters.
Suitable measuring instruments must offer a temperature measurement

of up to 350° C with a high accuracy.
Alternatively it is also possible to check the welding temperature with the

fusiotherm®-thermocolour crayon. The application of the special thermo-
colour chalk in the aluminium crayon enables an exact reading with a
tolerance of +/- 5 K to heated surfaces.
Application:
After the temperature pilot lamp of the welding device has indicated the
end of the heat-up period, put a firm chalk line on the heated external sur-
face of the welding tool. The colour must change within 1 - 2 seconds.
If the temperature is too high, the colour will change immediately and if it
is too low (below 260° C) it will change after 3 or more seconds.
If the colour does not change within 1 - 2 seconds another temperature

test has to be carried out, respectively the control of the welding
device is required.
It is possible, that the printed colour differs slightly from the original
Temperature control by means of surface temperature Temperature control by chalk.

measuring instrument.
before after
24
TECHNIQUE
Part B:
Preparation for the fusion
3. Cut the pipe right-angled to the pipe axis.
Only use fusiotherm®-pipe cutters or other suitable cutting tools. Take

care that the pipe is free from burrs or cutting chips and remove if
necessary.
4. Mark the welding depth at the end of the pipe with the enclosed pencil
and template.
5. Mark the desired position of the fitting on the pipe and / or fitting.
The auxiliary markings on the fitting and the continued line on the
pipe may be used as a help.
Cutting of the pipe Marking of the welding depth
The fusion is subject to the following data
Pipe Welding Heat-up Welding Cooling

external-Ø depth time time time
mm mm sec. fs sec. min.
20 14.0 5 4 2
25 15.0 7 4 2
32 16.5 8 6 4
40 18.0 12 6 4
50 20.0 18 6 4
63 24.0 24 8 6
75 26.0 30 8 8
90 29.0 50 8 8 The General Guidelines
32.5 60 for Heated Socket Wel-
110 10 8
ding acc. to DVS 2207
125 40.0 70 10 8 Part 11 apply.
25
TECHNIQUE
Part B:
Heat-up of pipe and fittings
6. Push the end of the pipe, without turning, up to the marked welding
depth into the welding tool and at the same time the fitting, without
turning, as far as it will go on the tool. It is essential to observe the
above mentioned heating times.
Pipes and fittings of the dimensions Ø 75 to 125 mm may only be

welded with welding device Art.-No. 50341 (or with machine Art.-No.
50147). On using the fusiotherm®-welding machine Art.-No. 50147 a
separate operating instruction has to be observed.
ATTENTION:
The heating time starts, when pipe and fitting have been pushed with
the correct welding depth on and in the welding tool. Not before!
Part B:
Setting and alignment
7. After the stipulated heat-up time quickly remove pipe and fitting from
the welding tools. Join them immediately, without turning, until the
mark welding depth is covered by PP-bead of the fitting.
ATTENTION:
Do not push the pipe too far into the fitting, as this would reduce
the bore and in an extreme case may close the pipe.
8. The joint elements have to be fixed during the specified processing

time. Use this time to correct the connection. Correction is restricted
to the alignment of pipe and fitting. Never turn the elements or align
the connection after the processing time.
9. After the cooling period the fused joint is ready for use.
The result of the fusion of pipe and fitting is a permanent material

joining of the system elements.
Unrivaled connection technique with security for a life-time!
Warming Joining, fixing and… …aligning!
26
TECHNIQUE
Visual inspection of fusion seam
Normally on fusioning a bead is formed around the entire circumference

at the edge of the socket. This bead is an indication of proper welding.
Incorrect shape of bead
Different shape of bead (b) or non-existent bead at one

1 or at both ends (a) (partial or total extent), resulting from:
➟ temperature of heating tool is too low (a)
➟ heat-up time too short (a)
➟ unacceptable tolerances (a and b)
➟ excessive temperature of heating tool (b)
➟ heat-up time too long (b)
Single shape of bead, resulting from:

2 ➟ heat-up time too short
➟ temperature of heating tool is too low
➟ unacceptable tolerances
➟ heat-up of only one welding-part
Excessive melting, resulting from:

3 ➟ temperature of heating tool is too high
➟ misaligned movement of welding-part, e.g. by inadequate fixing
➟ unacceptable tolerances
Elbow variance
4
Partially or double-sided inclined welded pipe into the socket without or
with slight bracing, resulting from:
➟ machinery defect
➟ false installation
Acceptable, if e ≤ 2 mm
Mistake of bonding by improper pipe insertion,

5 resulting from:
➟ heat-up time too short

➟ pipe ends not at 90° (right-angled)
➟ heating temperature too low
➟ axial movement during cooling time
➟ change-over time too long
Acceptable up to 0.1 x d and 0.15 x socket depth
27
TECHNIQUE
Visual inspection of fusion seam
➟ correct fusion welding
a b
1 2
e
300
3 4
The visual inspection may be only a first

indication of the welding seam quality.
d
But it is not a replacement for the leak

test, which has to be carried out after the
completion of the installation.
x
5
Source:
DVS 2202-1, to purchase at DVS-publisher, Düsseldorf Copyright Publisher for fusion and related
procedures DVS-Verlag GmbH
28
TECHNIQUE
Part C:
Weld-in saddles
For pipe external diameters of 40, 50, 63, 75, 90, 110, 125 mm
D d R h Sensorwells Drill Welding Tool

Art.-No. Dimension
mm mm f mm ømm Art.-No. Art.-No.
4115156 40/20 mm 40 20 - 27.0 - 50940 50614
4115158 40/25 mm 40 25 - 28.0 - 50940 50614
4115160 50/20 mm 50 20 - 27.0 - 50940 50616
4115162 50/25 mm 50 25 - 28.0 - 50940 50616
4115164 63/20 mm 63 20 - 27.0 - 50940 50619
4115166 63/25 mm 63 25 - 28.0 - 50940 50619
4115168 63/32 mm 63 32 - 30.0 - 50942 50620
4115170 75/20 mm 75 20 - 27.0 - 50940 50623
4115172 75/25 mm 75 25 - 28.0 - 50940 50623
4115174 75/32 mm 75 32 - 30.0 - 50942 50624
4115175 75/40 mm 75 40 - 34.0 - 50944 50625
4115176 90/20 mm 90 20 - 27.0 - 50940 50627
4115178 90/25 mm 90 25 - 28.0 - 50940 50627
4115180 90/32 mm 90 32 - 30.0 - 50942 50628
4115181 90/40 mm 90 40 - 34.0 - 50944 50629
4115182 110/20 mm 110 20 - 27.0 - 50940 50631
4115184 110/25 mm 110 25 - 28.0 - 50940 50631
4115186 110/32 mm 110 32 - 30.0 - 50942 50632
4115188 110/40 mm 110 40 - 34.0 - 50944 50634
4115189 110/50 mm 110 50 - 34.0 - 50946 50635
4115190 125/20 mm 125 20 - 27.0 - 50940 50636
4115192 125/25 mm 125 25 - 28.0 - 50940 50636
4115194 125/32 mm 125 32 - 30.0 - 50942 50638
4115196 125/40 mm 125 40 - 34.0 - 50944 50640
4115197 125/50 mm 125 50 - 34.0 - 50946 50642
4115198 125/63 mm 125 63 - 38.0 - 50948 50644
4128214 40/25x1/2“ f 40 - 1
/2“ 39.0 14 50940 50614
4128216 50/25x1/2“ f 50 - 1
/2“ 39.0 14 50940 50616
4128218 63/25x1/2“ f 63 - 1
/2“ 39.0 14 50940 50619
1 1
4128220 75/25x /2“ f 75 - /2“ 39.0 14 50940 50623
4128222 90/25x1/2“ f 90 - 1
/2“ 39.0 14 50940 50627
4128224 110/25x1/2“ f 110 - 1
/2“ 39.0 14 50940 50631
4128226 125/25x1/2“ f 125 - 1
/2“ 39.0 14 50940 50636
4128234 40/25x 3/4“ f 40 - 3
/4“ 39.0 16 50940 50614
3 3
4128236 50/25x /4“ f 50 - /4“ 39.0 16 50940 50616
4128238 63/25x 3/4“ f 63 - 3
/4“ 39.0 16 50940 50619
3 3
4128240 75/25x /4“ f 75 - /4“ 39.0 16 50940 50623
4128242 90/25x 3/4“ f 90 - 3
/4“ 39.0 16 50940 50627
4128244 110/25x 3/4“ f 110 - 3
/4“ 39.0 16 50940 50631
4128246 125/25x 3/4“ f 125 - 3
/4“ 39.0 16 50940 50636
4128260 75/32x1“ f 75 - 1“ 43.0 20 50942 50624
4128262 90/32x1“ f 90 - 1“ 43.0 20 50942 50628
4128264 110/32x1“ f 110 - 1“ 43.0 20 50942 50632
4128266 125/32x1“ f 125 - 1“ 43.0 20 50942 50638
29
TECHNIQUE
Part C:
Weld-in saddles
1. Before starting the welding process, check if the fusiotherm® -
welding devices and tools meet the requirements of “Fusion Part A”.
2. The first step is to drill through the wall of the pipe at the point inten-
ded for the outlet by using the fusiotherm®-drill.
branch 20/25 mm: Art.-No. 50940

branch 32 mm: Art.-No. 50942
3. The welding device/saddle welding tool must have reached the

required operating temperature of 260 °C (check with reference to
“Fusion Part B, item 2”).
4. The welding surfaces have to be clean and dry.
5. Insert the heating tool on the concave side of the weld-in saddle tool
into the hole drilled in the side wall of the pipe until the tool is completely
in contact with the outer wall of the pipe. Next the weld-in saddle spigot
is inserted into the heating sleeve until the saddle surface is up against
the convex side of the welding tool. The heating time of the elements is
generally 30 seconds.
6. After the welding tool has been removed, the weld-in saddle spigot is
immediately inserted into the heated, drilled hole. The weld-in saddle
should then be pressed on the pipe for about 15 seconds. After being
allowed to cool for 10 minutes the connection can be exposed to its full
loading. The appropriate branch pipe is fitted into the sleeve on the
fusiotherm®-weld-in saddle using conventional fusion technology.
By fusing the weld-in saddle with the pipe outer surface and the pipe inner
wall the connection reaches highest stability.
Drilling Heat-up... ...of pipe and fitting Joining

through the pipe wall
30
TECHNIQUE
Part D:
fusiotherm®-welding machine
➟ One wooden transport box for the welding machine
➟ One machine body with substructure, welding plate
➟ One set clamping jaws composed of 8 two-part jaws bars for pipes
and fittings, diameter 25, 32, 40, 50, 63, 75, 90, 110, 125 mm
➟ One fusiotherm®-welding tool diameter 50, 63, 75, 90, 110, 125 mm
➟ One welding device Art.-No.: 50341
➟ One Allan key and tool change clamp
➟ One fusiotherm®-thermocolour crayon
➟ One Installation manual
The fusiotherm®-welding machine was especially developed for stationary

welding of pipe and fittings with an external diameter of 50 to 125 mm. This
machine is equipped with a hand crank to facilitate a precise pre-assembly of
complicated installation parts.
The fusion is subject to the following data
Pipe- Welding Welding Cooling

Heating time
external-Ø depth time time
mm mm sec. fs sec. min.
50 20.0 18 6 4
63 24.0 24 8 6
75 26.0 30 8 8
90 29.0 50 8 8
110 32.5 60 10 8
125 40.0 70 10 8
The General Guidelines for Heated Tool Socket Welding acc. to

DVS 2207 Part 11 apply..
Part D:
Support intervals
firestop-pipe SDR 7.4 Pipe diameter d [mm]
Table to determine support intervals in con- 20 25 32 40 50 63 75 90 110 125

junction with outside diameter. Support intervals in cm
120 140 160 180 205 230 245 260 290 320
31
TECHNIQUE
Part E:
Repair
Damaged pipes may be repaired - as already mentioned - by fusion welding
(see part B).
In addition the firestop-system offers the possibility of repair by repair
stick.
The suitable welding tool (Art.-No. 50307/11) and the repair stick
(Art.-No. 4160600) are described on page 17 and 20.
The installation information is enclosed with the welding tool, but may also
be ordered separately.
Heat-up
Pipe repair stick Cutting
32
TECHNIQUE
Laying of aquatherm firestop-pipes

in the concrete
Part 1:
Connecting of pipe work to the

firestop sprinkler outlet
The connection is described in picture 1 as follows:

The base part of the sprinkler outlet (1) is screwed with 4 screws on the
shuttering.
Brass plug (2), upper part of the sprinkler outlet (3) and firestop connecti-
on piece (4) are connected to each other and plugged onto the base part
of the sprinkler outlet (1), so that part 3 is flushed with the shuttering.
Picture 1
Detailed information regarding the different dimensions of the sprinkler

outlet please take from tables on page 13!
Colour of plastic sleeve may differ.
33
TECHNIQUE

in the concrete
The firestop sprinkler connection is finished (picture 2).
Picture 2 (sectional view)
When removing the shuttering (after pouring of the concrete) the

base part of the sprinkler outlet (1) is pulled out of the upper part of the
sprinkler outlet (3).
The brass plug (2) is unscrewed from the firestop-connection piece (part
4). Now, the upper part of sprinkler outlet (3) can be pulled out of the
concrete easily.
The sprinkler connection (picture 3) can be completed very easily.

The, acc. to CEA 4001, required distance from the sprinkler head to the
completed ceiling, can be accomplished with the compensating fitting from
the sprinkler connection thread up to the firestop connecting piece (see
drawing page 35).
Picture 3
34
TECHNIQUE

in the concrete
3 cm
sprinkler outlet
standard extension /
compensating fitting a = acc.
CEA 4001
35
TECHNIQUE

in the concrete
Part 2:
Pressure test of pipe work installation

as strength test and leak test
Please refer to the information on page 40 – 42.
Part 3:
What must be considered during the

concreting process?
The pipe sections must be fixed every 1.5 to 2 m in a way (using pipe
hangers or lacing cord) to avoid sagging or bowing during the concreting
process. It is important, that the pipe work is completely embedded
without any hollow spaces (cavities).
The entering of the pipes during the concreting process must be avoided.
The compacting of the concrete with concrete vibrators in the pipe area
should be carried out carefully.
Open pipes and connections must be closed before the concreting.

The competent office of VDE shall be informed about the date of the
pressure test and the concreting. VDS decides on their participation
during the pressure test and/or the concreting process.
36
TECHNIQUE

in the concrete
Part 4:
Access to connection of the pipe work

in concrete
Option 1:
The pipe work in the concrete should be connected to the supply pipe, that
the connection can be accessed in case of damage.
This may accomplished as follows: Before applying the concrete on the

ceiling, a form work (casing) should be constructed around the connection
(allow enough space for installation work). The connection is embedded in
sand or similar fill of F90-quality in the form work.
The ceiling can be filled with concrete, now. After striking the ceiling, the
connection can be laid open and is now accessible. The subsequent sealing
of the cavity in the ceiling can be made with elements of F90-quality.
The access must be visible at all times (indicated on the drawing or by
marking the ceiling).
Option 2:
Before casting the connection can be packed in a Rockwool-fire protection
panel Conlit 150 U (allow enough space for installation work).
This panel has the following features:
light, water-repellent, pressure-resistant, self-supporting rockwool panel
covered with glass grid
Fields of application:
fire protection covering for steel construction F30–A-F180-A,
Increase of fire resistance class of concrete coverings.
Not flammable A2 acc. to DIN 4102, Part 1. Melting point >1000° C.
After shuttering of the ceilings the fire protection panel Conlit 150 U can
remain in the completed ceiling and can be adjusted to the structure of
the concrete ceiling by plastering.
The access shall be visible, as in option 1, at all time.
Drawing according to options 1 and 2
Access to the connection of the pipe work in concrete

riser
opening for inspection pipe
37
TECHNIQUE

in the concrete
Damaged pipe work in concrete,
e.g. by drilling work
Damaged pipe work can be repaired by fusion welding

(see firestop-sprinkler pipe system, Part B).
The firestop system can also be repaired using the pipe repair stick
(see firestop sprinkler system, Part E)
Part 5:
Bridging of building joints
The expansion or firestop-pipes depends on the temperature of the pipe

material. Cold water supplies cause hardly any expansion for a normal
assembly nor do normal outside temperatures.
The expansion need not to be considered when laying firestop-pipes in the

concrete. Rising pressures- and tensile stresses are not critical, as they are
absorbed by the material.
However, if it is necessary to bridge the expansion or the building joints, the

firestop pipes must be equipped with an approx. 25 cm protection pipe at
both ends of the joint.
The coefficient of expansion of firestop-pipes is 0.035 mm/mK

The coefficient of expansion of concrete is 0.05 – 0.12 mm/mK.
Part 6:
Potential equalizing
The VDE 0190 Part 410 and 540 requires a potential equalizing between
all kinds of earth conductors and the existing “conductible” potable and
waste water supplies and heating pipes. As firestop is not a conductible pipe
system, it cannot be used for potential equalizing and thus needs no earth
wiring.
The potential equalizing is made according to VDE-standard from the buil-

ding parts, which have to be earth wired, directly to the potential equalizing
rail to the planned position. The constructor or site manager must advise
the client or his representative, that an approved electrician must check, if
the firestop installation does not affect the existing electrical protection and
earth wiring measurements (VOB Part C, generaltechnical conditions of
contract ATV).
38
TECHNIQUE

in the concrete
Part 7:
Pressurizing in the firestop-supply

during the concreting process
During the concreting process the pipe must be pressurized with the
admissible operating pressure, so that a damaged point is visible at once.
After the pressure test the admissible operating pressure is kept by shut
off of the respective pipe. The applied measuring devices must grant a
correct reading of pressure changes of 0.1 bar.
The pressure measuring device shall be installed at the deepest point of

the pipe system.
Part 8:
Influence of the concrete to the

applied compounds
The firestop-pipe system contains all required compounds for a
complete system installation. Mixed installation with non-system and/or
non-material compounds are not required.
All material is resistant to corrosion. The threads of the firestop-sprinkler

connection fittings are made from brass (CuZn36Pb2As).
Experiences with this material confirm that the alloy has an excellent
resistance against concrete.
The general building regulations have to be complied with locally.

If special chemical additives (retarder, etc.) are applied, information from
the manufacturer of the concrete should be gathered; refer to aquatherm
for suitablity.
39
TEST
Pressure test
All pipelines have to be hydraulically pressure tested. The test pressure

must be 1.5 times of the operating pressure.
Due to the material properties of firestop pipes a pressurization causes

an expansion of the pipe, which influences the test result. Different
temperatures of pipe and test medium also lead to alterations of pressu-
re. A temperature change of 10 K corresponds to a pressure difference
of 0.5 to 1 bar. The pressure test of the firestop-system should be made
with a constant temperature of the medium.
The hydraulic pressure test requires a preliminary, principal and final test.
In the preliminary test the system is pressurized with the 1.5 times of the
maximum operating pressure. This test pressure has to be re-established
twice within 30 minutes within an interval of 10 minutes. After a test time of
a further 30 minutes the test pressure must not drop more than 0.6 bar.
No leakage may appear.
The preliminary test is to be followed directly by the principal test. Test

time is 2 hours. Now the test pressure taken from the preliminary test
may not fall more than 0.2 bar.
Upon completion of the preliminary and principal tests the final test must
be conducted. In the final test the system is pressurized in a frequency of
5 minutes with a changing test pressure of 10 and 1 bar.
Between each test course the pressure has to be released.
No leakage must appear at any point of the tested system installation.
Measuring of the test pressures
Measuring has to be done with a manometer allowing a perfect reading of

a pressure change of 0.1 bar. The manometer has to be placed at the dee-
pest point of the installation.
Test record
A record of the hydraulic pressure test has to be prepared and signed by

the client and contractor stating place and date (see page 42).
40
TEST
Leakage test / Pressure diagram
Preliminary- and Principal test
Final test
41
TEST
Test record firestop system installation

Description of the installation Preliminary test
Place: max. working pressure x 1.5 bar
Object:
Pipe-lengths: Ø 16 mm m Pressure drop after 30 minutes: bar

Ø 20 mm m (max. 0.6 bar)
Ø 25 mm m
Ø 32 mm m Result preliminary test:
Ø 40 mm m
Ø 50 mm m Principal test
Ø 63 mm m
Ø 75 mm m
Ø 90 mm m
Ø 110 mm m Working pressure: bar
Ø 125 mm m (Result preliminary test)
Ø 160 mm m
Ø 200 mm m
Ø 250 mm m
Highest tapping m Pressure after 2 hour: bar

(over manometer)
Start of the test: Result principal test:

End of the test:
Test period: Final test*
1. working pressure 10 bar: bar

Client: at least 5 minutes, then
working pressure 1 bar: bar
at least 5 minutes

Contractor: at least 5 minutes, then
at least 5 minutes

Place: at least 5 minutes, then
Date: at least 5 minutes
* Unpressurize the pipe between each cycle.
Stamp / Signature
42
TEST
Enquiry for the chemical resistance of the

aquatherm firestop-pipe system
aquatherm GmbH
Technical department
Biggen 5 . D-57439 Attendorn E-mail: [email protected]
Phone: +49 (0) 2722 950 - 0 Internet: www.aquatherm.de
Fax: +49 (0) 2722 950 - 290
Installer: Field of application:

Company: Fluid transported
Contact °C/°F Operating temperature
Street mbar/psi Working pressure
PC / City h/d Service life
Phone % Concentration
Fax
E-mail Ambient medium:
Building project:
°C/°F Ambient temperature
Street mbar/psi Ambient pressure
City
enclosed not
Data sheets enclosed
Fluid transported ■ ■
Ambient medium ■ ■
Place, Date / Signature
43
REFERENCE
References
Office Building ˝Römischer Hof˝

Berlin, Germany
44
REFERENCE
References
Raschal - Centre for children surgery

and traumatology Moskau, Russia
45
REFERENCE
References
Office Building
Moskau, Russia
46
REFERENCE
References
Shopping Centre
Moskau, Russia
47
REFERENCE
References
Hotel
Turkey
48
REFERENCE
References
Carpet warehouse
Turkey
49
REFERENCE
References
Hotel
Sweden
Important advice:
The pictures present the way of installation in the respective countries. As this vary locally, the
application of firestop in any case has to be agreed and coordinated with the local national fire
protection authorities, the constructor and the building insurers.
50
Länderliste Elke 08.02.2007 9:21 Uhr Seite 1
WORLDWIDE
aquatherm - successful worldwide

in more than 70 countries!
country partner address phone fax e-mail
Australia Aquatherm Australia Pty Ltd. 415 West Botany Street AU 2216 Rockdale NSW 0061295537199 0061295537899 [email protected]
Austria Sanitär-Heinze GmbH
Wholesalers: Fachgrosshandel Gradner Strasse 100 A 8055 Graz 0043316295581 0043316296630 [email protected]
Haselauer
Sanitärgrosshandel Ges.mbH Pummererstr. 13 A 4020 Linz [email protected]
Seifrid Gesellschaft mbH Znaimerstr. 57 A 2020 Hollabrunn 00432952202400 004329522024020 [email protected]
Carl Steiner Handelszentrum 4 A 5101 Bergheim 0043-6624-682218 [email protected]
Sanitär-Heinze GmbH
Fachgrosshandel Rubensstraße 40 A 4050 Linz 00437323866510 0043732387706 [email protected]
Fachgrosshandel Franz-Sauer-Straße 40 A 5013 Salzburg 0043662449440 004366244944 168 [email protected]
Fachgrosshandel Mariazeller Straße 256 A 3100 St. Pölten 004327428811050 00432742881751 [email protected]
Advisor: Maximilian Köck Dorfstrasse 106 A A 6240 Radfeld 004369911169427 [email protected]
Belgique Ets. A. Marchal & Cie. 4e Ave., Parc Industriel B 4040 Herstal 003242569360 003242480671 [email protected]
S.P.R.L. des Hauts Sarts
Bosnia- Vokel d.o.o. Veleprodaja-Maloprodaja BiH 88240 Posusje 0038739693002 0038739693156 [email protected]
Hercegovina Vinjani b.b.
Botswana EuroDrain Technology (PTY) Ltd Private Bag X.9 ZA 2010 Benmore 00270117012201 00270117012223 [email protected]
Postnet Suit 688
Canada Aquatherm CA, Inc. P.O. Box 2624 Cardston, 0014036534440 0014036534446 [email protected]
AB T0K 0K0
China (P.R.) KDF. Distribution 908, 9th Floor, PRC 200030 Shanghai 00862164073666 00862164478801 [email protected]
(Shanghai) Co., Ltd. 1 Grand Gateway
No. 1 Hong Qiao Road
Croatia a q t d.o.o. Radnicka Cesta 1A HR 10000 Zagreb 0038516194030 0038516184592 [email protected]
Czech Rep. AEROFLEX Prazka 298, P.O.Box 28 CZ 25036 Brandys/ 00420326907288 00420326907288 [email protected]
Labem-Stara Boleslav
Denmark WS Rorhandel c/o Revisorgarden DK 6270 Tonder 004573724033 004572724032 [email protected]
Norremarksvej 84
Egypt Hamza Bros. Supplying Co. 53 El Soudan St. EG GIZA Cairo 002023367832 002027613314 [email protected]
El Mohandseen
Faroer Islands P/F Demich Stidagota 1 FO 100 Torshavn 00298309310 00298309311 [email protected]
Finland Finaquatherm Oy Hatanpaanvaltatie 34 A FI 33100 Tampere 0035833469803 0035833469878 [email protected]
Georgia "Hydrotherm" Ltd. 118, A. Tsereteli Ave. GEO 380019 Tbilisi 0099532940564 0099532940564 [email protected]
Great Britain Aquatherm sales UK Ltd. Unit 23 Bolney GB RH17 Bolney West Sussex 00441444 250500 00441444 250456 [email protected]
Grange Business Park 5PA
Stairbridge Lane
Hellas Aquatherm Hellas A.B.E.E. Aerogefira GR TK Saloniki Polichni 00302310683869 00302310683871 [email protected]
Askilipiou Str. 1 / Langada 56430
Hong Kong Chivas Corporation Ltd. Rm 1211, Technology Park HK Shatin, N.T. Hong Kong 0085225219768 0085225265310 [email protected]
18 On Lai Street Siu Lek Yuen
Hungary aquatherm-hungaria kft. Hársfa sétány 13, fszt. 2 H 1203 Budapest 003614254095 003614254095 [email protected]
India aquatherm India C-4, Dhanraj Industrial IN 400013 Mumbai 009122-5660 5197/ 00912224983286 [email protected]
Estate Lower Parel 5660 5198 [email protected]
Ireland Thermax Supplies, Ltd. Hollywell IE Kilfenora, Co. Clare 00353868200027 00353657088271 [email protected]
Iceland Vatnsvirkinn hf Smidjuvegi 44d IS 200 Kópavogur 003545101400 00354-510 1410 [email protected]
Israel S.AL Technical Equipment Ltd. 36 Hamerkava St. IL 58859 Holon 97235566363 97235566470 [email protected]
Italy aquatherm SRL Parco Produttivo Apuania I 54100 Massa (MS) 00390585259901 00390585259999 [email protected]
(Ex Area Dalmine)
Japan Toyox Co. Ltd Toyama - pref. JP 4371 MaezawaKurobeCity 0081765525636 0081765524245 [email protected]
Korea EURO International Co., Ltd. #614 Life Combi B/D, Gu KR Seoul 0082278271612 008227827163 [email protected]
61-4 Yoido-Dong, 150732
Youngdeungpo
Kuwait Al-Sahoo General Trading Safat, Zip Code 13033 KW 13033 Kuwait-City 009654910190/ 00965-4910194 [email protected]
& Contracting Group Co., P.O. Box 32 10 4910192
Latvia SIA "RK Konsultants" Césu iela 29 LV 1012 Riga 003717375962 003717375964 [email protected]
Libanon Kamaco S.A.L. Antelias Highway LE Antelias 009614402329 009614405210 [email protected]
Luxemburg Ets.A.Marchal & Cie. S.P.R.L. 4e Ave., Parc Industriel B 4040 Herstal 003242646568 003242480671 [email protected]
Malta aquatherm (Malta) Ltd. Triq Dun Luret Callus MA ZBG 07 Zebbug 0035621462697 0035621462698 [email protected]
Montenegro DRAM Ltd. Aleksandra Aca Prijica b.b. 81000 Podgorica 0038181224 912 0038181224749 [email protected]
Wholesaler: ADRIATIC SBS Kaliman bb 82000 Tivat 0038182673 980 0038182673980
Namibia O. Behrens & Co. (Pty.) Ltd. P.O. box 5042 NA Windhoek 0026461238300 0026461238743 [email protected]
Sanitaryware
Netherlands ERIKS bv Saffierstraat 1 NL 1812 RM Alkmaar 0031725141392 0031725155645 [email protected]
New Zealand Aquatherm NZ 88 Carbine Rd. NZ Auckland 006495707204 006495707206 [email protected]
Norway KVT Klima- & Varme Teknikk A/S Postfach 2189 NO 1522 Moss 004769242929 004769242930 [email protected]
Holly Hansensgt. 21
Philippines Kuysen Enterprises, Inc. 232-234 Rizal Avenue Ext. PHI 1400 Caloocan 006323642041 006323621193/ [email protected]
City Metro Manila / 42, 43,44 -23649759
Polska aquatherm-Polska ul. Pulawska 538 PL 02-884 Warszawa 0048223210000 0048223210020 [email protected]
Portugal Compoterm, Lda L. Monte-Oleiros Park, Lt. 4730-325 Oleiros WD 00351253925610 00351253925 611 [email protected]
Qatar Al Sahoo Trading & Contr. Co. P.O. Box 23446 UAE Doha - Qatar 009744696886 009744696987 [email protected]
Romania Romstal Imex SRL Sos.Vitan Barzesti nr.11 RO 042122 Bucuresti 0040728628133 0040213320901
sector 4
Russia Sokol ul. Juzhnobutovskaja 45 GUS 117042 Moscow 0074957107134/ 0074957107138 [email protected]
35/36/37
Russia aquatherm-Königsberg Glasunov 11 GUS 236010 Kaliningrad 0074012330833 0074012331005 [email protected]
Russia Lazurit 6a, Vokzalnaya Magistral GUS 630004 Novosibirsk 0073832183950 0073832237348 [email protected]
Saudi Arabia Al Sahoo Sanitary Ware Co. P.O. Box 27478 SA 11417 Riyadh 0096614779140 0096614764271 [email protected]
Switzerland Thermotech GmbH Heimeliweg 7 CH 8952 Schlieren 0041438173053 0041438173054 [email protected]
Serbia Delta Term Export Import Sime Milosevica 12 SCG 11000 Belgrad 00381112457722 00381113440705 [email protected]
/ 3089135
Singapore Sintalow Hardware PTE.LTD Head Office No.8 SGP 629786 Singapore 006562615966 006562620932 [email protected]
Fan Yoong Road
Slovenia Rep. Martin d.o.o. P.E. Hmeljarska SI 3310 Zalec 0038637132620 0038637132600 [email protected]
Slovac Rep. S-Komplex Hrobonova 4 SK 81104 Bratislava 00421754788225 00421754788204 [email protected]
Spain aquatherm ibérica s.l. C/Torre de E 28031 Madrid 0034913806608 0034913806609 [email protected]
Don Miguel, n° 26
Sri Lanka Tritech Marketing International (Pvt) Ltd. LK Colombo 0094115544233 0094114815201 [email protected]
No. 87, Makola South, Makola Kiribathgoda
South Africa EuroDrain Technology (PTY) Ltd Private Bag X.9 ZA 2010 Benmore 00270117012201 00270117012223 [email protected]
Postnet Suit 688
Sweden R.E. Therm Rörprodukter Frillesasvägen 83 SE 43030 Frillesas 0046340657800 0046340650268 [email protected]
Syria SARA SYRIA P.O. Box 33073 SY Damascus 00963113734646 00963113734733 [email protected]
Malki - Bizem St.
Tunisia Société de Distribution 29 bis, Rue Oum Kalthoum TN 1001 Tunis 00216-71 342 866 00216-71 342 857 [email protected]
de Quincaillerie /867
Turkey Gelisim Teknik-Ticaret SanayivePazarlamaLtd.Sti. TR 7050 Antalya 00902423402575 00902423402577 [email protected]
Apt. B-Blok No: 12/1-2
100. Yil Bulvari Sevimli
Thailand Cosmopolitan Trading Co., Ltd. 48/2 Soi Naphasap 2 TH 10110 Bangkok 006622596052-3 006622586208 [email protected]
Sukhumvit 36 Road [email protected]
UAE Al Sahoo Trading Est. P.O. Box 16742 UAE Dubai-Deira 0097142690156 0097142625459 [email protected]
Salahudin Street
Ukraina aquatherm-Ukraine Prospekt W. UA 79058 Lviv 00380322949310 00380322403187 [email protected]
Tschornowola 4 Büro 15
USA aquatherm piping systems, llc. 2155 Bonie Brae Street USA 48309 Rochester Hills, 0012488307037 0012483758035 [email protected]
Michigan
Vietnam Lotus Chemical Technology 393 Dien Bien Phu St. VN Ho Chi Minh City 008488327605 008488327730 [email protected]
Ward 4, Dist. 3
Albania, Algeria, Bulgaria, Brazil, Cuba, France, Kazakhstan, Lithuania, Moldavia: These countries are supplied with our products by different traders.
Addresses are available from the aquatherm export department: +49 (0)2722 950 -121/-122/-123/-124/-125
51
NOTES
52
NOTES
53
NOTES
Our General Conditions of Sale and Delivery (Date: January 2007),
These are printed completely on our homepage www.aquatherm.de
or we will send them to you on demand!
Subject to technical changes.
54

Fire Stop

Uploaded by

Copyright:

Available Formats

Fire Stop

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Fire Stop

Uploaded by

Copyright:

Available Formats

05/08

FirestopInternational 29.11.2006 9:22 Uhr Seite 1

- Material properties / Advantages

- Visual inspection of fusion seam

Laying of firestop pipes in the concrete 33-39

- Leakage test / Pressure diagram

The system is based on a fibre reinforced polypropylene pipe (faser

aquatherm firestop is:

- connection by fusion welding

The production of pipes and fittings is controlled according to the highest

The aquatherm quality management system is certified according to

Double material thickness at the joint – giving double safety at the

A permanent leakproof connection is created with the aquatherm fusion

Whereas in case of tees three joints are to be processed, work is limited

Fire protection requirements

Thus, the application of

Further certification either

Transport and storage

firestop-pipes can be stored in all outside temperatures. Pipes should be

Although firestop-pipes are extremely robust, it is recommended to treat

Procedures for additional repair

On account of the special material qualities firestop-pipes and fittings pro-

Pipe friction loss

The pressure loss caused by friction is to be calculated hydraulically with the

The value to be used for C is 150, applicable for calculations of sprinkler

Equivalent lengths for the

The equivalent lengths of transition pieces, threaded connexions and

firestop-pipe SDR 7.4 / B1

Material : PP-R (80) FS

Wall Internal Water

4170710 25 mm 100 25 3.5 18.0 0.254 0.236 15

4170712 32 mm 40 32 4.4 23.2 0.423 0.379 20

4170714 40 mm 40 40 5.5 29.0 0.661 0.590 25

4170716 50 mm 20 50 6.9 36.2 1.029 0.919 32

4170718 63 mm 20 63 8.6 45.8 1.647 1.444 40

4170720 75 mm 20 75 10.3 54.4 2.324 2.054 50

4170722 90 mm 12 90 12.3 65.4 3.359 2.943 65

4170724 110 mm 8 110 15.1 79.8 5.001 4.403 80

4170726 125 mm 4 125 17.1 90.8 6.475 5.669 90

firestop-elbow 90º / B1 female / male

firestop-elbow 45° / B1 female / male

firestop-base part for sprinkler outlet

firestop-upper part for sprinkler outlet

firestop-plug for sprinkler outlet

firestop-weldable flange adapter / B1

Art.-No. Dimension Packing Price/ Product-

firestop-back plate elbow / B1

firestop-transition piece / B1 round

firestop-transition piece, female / B1

firestop-transition piece / B1 with hexagon

firestop-threaded branch tee / B1

firestop-threaded connection union/ B1

Art.-No. Dimension Packing Price/ Product-

firestop-female part union / B1

Packing Price/ Product-

Packing Price/ Product-

firestop-transition piece for groove connection

Art.-No. Dimension Packing Price/ Product-

4128214 40/25 x 1/2” f 5 pc 1 42

firestop-pipe repair stick