PunchMan 85

cncKad
Punching Manual
cncKad
PunchMan.85.006
ii
Punching Manual
Copyright 2007
Metalix CAD/CAM.
All Rights Reserved
Limited Warranty
Metalix CAD/CAM Warrants the software will perform substantially in accordance with
the accompanying printed materials. Metalix CAD/CAM does not warrant that the
functions contained in the software will meet your requirements or that the operation of
the software will be uninterrupted or error-free.
Limitation of Liabilities
In no event will Metalix CAD/CAM or its suppliers be liable for direct, indirect, special,
incidental, contingent, consequential or similar damages of any kind resulting from any
defect in the software or documentation, including without limitation, any lost profits or
savings.
Metalix CAD/CAM LTD

Koranit
D.N. Misgav 20181
ISRAEL
Tel: (+972) 4-999 8436
Fax: (+972) 4-999 8519
E-mail: [email protected]
Copyright 2007
iii
cncKad
iv
Punching Manual
Table of Contents
Introduction ................................................................................................................... 1
1
Punch Manual ......................................................................................................... 2

1.1 Add Punch......................................................................................................... 2
1.1.1
Single Punch ............................................................................................ 2
1.1.1.1 Single.................................................................................................. 3
1.1.1.2 On Line ............................................................................................... 3
1.1.1.3 On Arc ................................................................................................ 4
1.1.1.4 In Window........................................................................................... 4
1.1.1.5 Punch All ............................................................................................ 5
1.1.1.6 Punch Free Hand ............................................................................... 5
1.1.1.6.1
Dynamic Angle Change ............................................................. 5
1.1.1.7 On Punched Entity.............................................................................. 5
1.1.2
Nibble Entity ............................................................................................. 6
1.1.3
Nibble Chain ............................................................................................. 6
1.1.4
Nibble Contour.......................................................................................... 6
1.1.5
Nibble Start-End ....................................................................................... 7
1.1.6
Crunch ...................................................................................................... 7
1.1.6.1 Crunching a notch with one tool ......................................................... 8
1.1.7
Crunch Right-Angled Triangle .................................................................. 9
1.1.8
Crunch Chamfer ....................................................................................... 9
1.1.9
Crunch Arc.............................................................................................. 10
1.1.10 Punching Grids ....................................................................................... 10
1.1.11 Choosing a Tool ..................................................................................... 11
1.1.12 Tool Positioning ...................................................................................... 11
1.1.12.1 Offset ................................................................................................ 12
1.1.12.2 Entity's End....................................................................................... 13
1.1.12.3 Tool's End Tangent........................................................................... 13
1.1.12.4 Next Entity's Tangent........................................................................ 13
1.1.12.5 Centered........................................................................................... 13
1.1.12.6 On Shape Center.............................................................................. 13
1.1.13 From Base Line ...................................................................................... 14
1.1.14 Tool Spacing........................................................................................... 14
1.1.14.1 Overlap Definition ............................................................................. 14
1.1.14.2 Step Definition .................................................................................. 15
1.1.14.3 Scallop Definition.............................................................................. 16
1.1.15 Tool Sequence ....................................................................................... 16
1.1.16 Use Tool Data......................................................................................... 16
1.1.17 Directional Punch option......................................................................... 17
1.1.18 Punch as Singles.................................................................................... 17
1.1.19 Wheel Connect ....................................................................................... 17
1.1.20 Functions button ..................................................................................... 17
1.1.21 Stop or Push Out .................................................................................... 17
1.1.22 Wire Joint................................................................................................ 17
1.1.22.1 Width ................................................................................................ 18
cncKad
1.1.22.2 Max Length ....................................................................................... 18
1.1.22.3 At Least One..................................................................................... 18
1.2 Auto Punch...................................................................................................... 19
1.2.1
Auto Punch Parameters tab ................................................................... 19
1.2.1.1 Tool Spacing Defaults ...................................................................... 20
1.2.1.1.1
Minimum Tool Overlap............................................................. 20
1.2.1.1.2
Scallop for Round Tools .......................................................... 20
1.2.1.2 Cutting Tools Restrictions................................................................. 20
1.2.1.2.1
Minimum Width ........................................................................ 20
1.2.1.2.2
Maximum Width ....................................................................... 20
1.2.1.3 Tool Selecting Preferences .............................................................. 20
1.2.1.3.1
Best Tools................................................................................ 20
1.2.1.3.2
Minimum Tools ........................................................................ 20
1.2.1.4 Odd hits, then Even hits ................................................................... 20
1.2.1.5 Punching scope ................................................................................ 20
1.2.1.5.1
Holes........................................................................................ 20
1.2.1.5.2
Notches.................................................................................... 21
1.2.1.5.3
Slitting ...................................................................................... 22
1.2.1.6 Use Tools Library ............................................................................. 22
1.2.1.7 Use Setup File .................................................................................. 22
1.2.1.8 Select Setup ..................................................................................... 22
1.2.2
Holes Tab ............................................................................................... 22
1.2.2.1 One Hit Only With matching Tool ..................................................... 23
1.2.2.2 Tolerance Settings............................................................................ 23
1.2.2.3 Crunch .............................................................................................. 24
1.2.2.4 Wire Joint.......................................................................................... 24
1.2.2.5 For Holes .......................................................................................... 24
1.2.2.6 Automatic Detection ......................................................................... 24
1.2.3
Slitting tab............................................................................................... 24
1.2.3.1 Micro Joint Parameters Section........................................................ 25
1.2.3.1.1
MJ Width.................................................................................. 25
1.2.3.1.2
MJ Width at Sheet Edge .......................................................... 25
1.2.3.1.3
MJ on corners .......................................................................... 25
1.2.3.1.4
Every corner ............................................................................ 25
1.2.3.1.5
The Minimal number of Micro Joints for this part ..................... 26
1.2.3.2 Wire Joints Parameters Section ....................................................... 26
1.2.4
Shapes Tab ............................................................................................ 26
1.2.4.1 Special Punching Section ................................................................. 26
1.2.4.1.1
Profile....................................................................................... 26
1.2.4.1.2
Shapes..................................................................................... 27
1.2.4.1.3
Tooling ..................................................................................... 27
1.2.4.2 Predefined Shapes Section .............................................................. 27
1.2.5
Punch and Cut Warnings Tab ................................................................ 28
1.2.5.1 Do Not Allow Over Tonnage ............................................................. 28
1.2.5.2 Do Not Allow Punch Destroys Part ................................................... 28
1.2.5.3 Do Not Allow No Station for Tool ...................................................... 29
1.2.5.4 Do Not Allow Over Travel in Y.......................................................... 29
vi
Punching Manual
1.2.5.5 Do Not Allow Punch Less than 1.5 Tool ........................................... 29
1.2.5.6 Do Not Allow Punch Step Less than Thickness................................ 29
1.2.5.7 Do Not Allow CAM in Clamp Dead Zone .......................................... 29
1.2.5.8 Do Not Allow CAM is out of X working Range .................................. 29
1.2.6
Punching sheet edge.............................................................................. 29
1.3 Deleting Punches ............................................................................................ 29
1.4 Set or Clear Last Hit on Center ....................................................................... 30
1.5 Directional Punch ............................................................................................ 30
1.5.1
Uni Directional ........................................................................................ 30
1.5.2
Bi Directional .......................................................................................... 30
1.6 Save As Predefined Shape ............................................................................. 30
2
The CAM Menu ..................................................................................................... 31

2.1 Setting Offsets................................................................................................. 31
2.1.1
Edit Offsets ............................................................................................. 31
2.1.2
Set Offsets.............................................................................................. 32
2.1.3
Set All the Offsets................................................................................... 32
2.2 Change Tool for Existing Punches .................................................................. 32
2.3 Edit CAMs ....................................................................................................... 33
2.4 Add MicroJoint................................................................................................. 35
2.4.1
MicroJoint ............................................................................................... 36
2.4.2
Wire ........................................................................................................ 37
2.5 Set Tool Sequence.......................................................................................... 37
2.6 Common Cuts ................................................................................................. 39
2.6.1
Vertical.................................................................................................... 39
2.6.2
Horizontal ............................................................................................... 40
2.6.3
Common Cuts Example.......................................................................... 40
2.7 Reposition and Transformation ....................................................................... 41
2.7.1
Transformations...................................................................................... 41
2.7.2
Reposition and Head position................................................................. 42
2.7.2.1 Add ................................................................................................... 42
2.7.2.2 Edit ................................................................................................... 42
2.7.2.3 Set CAMs to Current ........................................................................ 42
2.8 Push Out (Chute) ............................................................................................ 42
2.8.1
Chute Type ............................................................................................. 43
2.8.2
Push Out Modes..................................................................................... 43
2.8.3
Last Hit On Center.................................................................................. 44
2.8.4
Open Chute, then Last Hit ...................................................................... 44
2.8.5
Head up .................................................................................................. 44
2.8.6
Bin Number............................................................................................. 44
2.8.7
Auto Tool Order ...................................................................................... 44
2.8.8
User Defined Movement......................................................................... 44
2.8.8.1 Move ................................................................................................. 44
2.8.8.2 Open Chute, then Move ................................................................... 44
2.8.8.3 Reduce Speed for Movement ........................................................... 44
vii
cncKad
2.8.9
Push Out Profiles.................................................................................... 44
2.9 Add or Remove Stop Machine ........................................................................ 45

2.10 Positioning (No CAM)...................................................................................... 45
2.11 Cut Sheet ........................................................................................................ 45
2.11.1 Tools....................................................................................................... 46
2.11.2 Offset ...................................................................................................... 46
2.11.3 Wire Joint................................................................................................ 47
2.11.4 Cut Sheet Examples............................................................................... 47
2.11.4.1 Cut Sheet Left Right ......................................................................... 47
2.11.4.2 Cut Sheet Left Down ........................................................................ 48
2.12 Defining Functions........................................................................................... 48
2.12.1 Punch or Cut Functions .......................................................................... 48
2.12.1.1 Set CAM Functions........................................................................... 48
2.12.1.2 Edit CAM Functions.......................................................................... 49
2.12.2 Defining Tool Functions.......................................................................... 49
2.12.3 Defining Program Functions ................................................................... 50
2.13 Set Sheet and Clamps .................................................................................... 51
2.13.1 Sheet Tab ............................................................................................... 51
2.13.1.1 Sheet Size ........................................................................................ 53
2.13.1.2 Set Sheet = Part ............................................................................... 53
2.13.1.3 Select Sheet ..................................................................................... 53
2.13.1.4 Number of Parts ............................................................................... 54
2.13.1.5 Offsets .............................................................................................. 54
2.13.1.6 Sheet Area and Weight .................................................................... 54
2.13.1.7 Material Choice................................................................................. 54
2.13.1.8 Program Functions ........................................................................... 55
2.13.1.9 Sheet Thickness Choice................................................................... 55
2.13.1.10 Choosing Sheets Quantity................................................................ 55
2.13.1.11 Technology Parameters ................................................................... 55
2.13.1.12 Technology Table ............................................................................. 55
2.13.1.13 Sheet Type ....................................................................................... 55
2.13.1.14 Run the program............................................................................... 55
2.13.1.15 Start Parts Placement....................................................................... 56
2.13.2 Auto Tab ................................................................................................. 56
2.13.2.1 Buffer ................................................................................................ 58
2.13.2.1.1 Use Global ............................................................................... 58
2.13.2.1.2 Hole buffer size........................................................................ 58
2.13.2.1.3 Use Rectangular Border .......................................................... 58
2.13.2.1.4 Use Part Border ....................................................................... 58
2.13.2.2 Mirror Allowed................................................................................... 58
2.13.2.3 Direction ........................................................................................... 59
2.13.2.4 Common Cuts for Grouped Arrays ................................................... 59
2.13.3 Global Cut tab......................................................................................... 59
2.13.4 Cutting Parameters Tab ......................................................................... 60
2.13.4.1 Piercing............................................................................................. 61
2.13.4.2 Sheet Thickness and Material .......................................................... 61
viii
Punching Manual
2.13.4.3 Vaporization...................................................................................... 61
2.13.4.4 Dynamic Piercing.............................................................................. 61
2.13.4.5 Use PrePiercing................................................................................ 61
2.13.4.6 Use Standard Shapes ...................................................................... 62
2.13.4.7 Use Vaporize For Engrave ............................................................... 62
2.13.4.8 Cutting Speed................................................................................... 62
2.13.4.9 Point Marking Style........................................................................... 62
2.13.5 Part Tab.................................................................................................. 62
2.13.5.1 Part section....................................................................................... 63
2.13.5.1.1 Part Size View ......................................................................... 63
2.13.5.1.2 Number of Parts....................................................................... 63
2.13.5.1.3 Number of Holes...................................................................... 63
2.13.5.1.4 Entities Section ........................................................................ 64
2.13.5.1.5 Distance Between Parts .......................................................... 64
2.13.5.1.6 Parts in Geometry.................................................................... 64
2.13.5.1.7 Part Area.................................................................................. 64
2.13.5.1.8 Part Weight .............................................................................. 64
2.13.5.1.9 Bend Line K Factor .................................................................. 64
2.13.5.2 Sheet section.................................................................................... 65
2.13.5.2.1 Sheet Area............................................................................... 65
2.13.5.2.2 Sheet Weight ........................................................................... 65
2.13.5.2.3 Entities on Sheet...................................................................... 65
2.13.5.2.4 Parts in Geometry on Sheet .................................................... 65
2.13.5.2.5 Create unique IDs for entities .................................................. 65
2.13.6 Clamps Tab ............................................................................................ 65
2.13.6.1 Clamp Coordinates........................................................................... 66
2.13.6.1.1 Working in the Dead-Zone....................................................... 66
2.13.6.1.2 Changing the Sheet Size in X.................................................. 66
2.13.6.1.3 Changing the machine............................................................. 66
2.13.6.2 Max Used Clamps ............................................................................ 67
2.13.6.3 Restore defaults ............................................................................... 67
2.13.7 User Data Tab ........................................................................................ 67
2.13.7.1 Edit Titles.......................................................................................... 68
2.13.8 Sheet Processing Technology Tab......................................................... 68
2.13.8.1 Tools' Processing Strategy ............................................................... 69
2.13.8.1.1 All Sheet Processing................................................................ 69
2.13.8.1.2 Part Processing ....................................................................... 69
2.13.8.1.3 Stripe Processing..................................................................... 69
2.13.8.2 Tools Section.................................................................................... 70
2.13.8.3 Optimization Strategy ....................................................................... 70
2.13.8.4 Stripe section.................................................................................... 70
2.13.9 Trim Sheet Tab....................................................................................... 70
2.13.10 Reposition Tab ....................................................................................... 71
2.13.10.1 Manual Reposition............................................................................ 72
2.13.10.2 Auto Reposition ................................................................................ 72
2.13.10.2.1 Quantity of Repositions............................................................ 72
2.13.10.2.1.1 Minimum repositions ............................................................ 72
ix
cncKad
2.13.10.2.1.2 Minimum part breaks ........................................................... 72
2.13.10.2.1.3 User defined......................................................................... 73
2.13.10.2.2 Max/Min Processing ................................................................ 73
2.13.10.2.3 Reposition Safety..................................................................... 73
2.13.10.3 Tool Reverse Order for Reposition/Transformation.......................... 74
2.13.11 Load/Unload Tab .................................................................................... 74
2.13.11.1 Sheet Loading .................................................................................. 74
2.13.11.1.1 Loading Mode .......................................................................... 74
2.13.11.1.2 Pin............................................................................................ 74
2.13.11.1.3 Load On Opposite Side of Pin ................................................. 75
2.13.11.1.4 Sheet Measuring...................................................................... 75
2.13.11.1.5 Offset ....................................................................................... 75
2.13.11.2 Sheet Unloading ............................................................................... 75
2.13.11.2.1 Unloading Mode....................................................................... 75
2.13.11.2.2 Size of Processed Sheet ......................................................... 75
2.13.11.2.3 Correction for Processed Sheet............................................... 75
2.13.12 Laser Optimization tab............................................................................ 75
2.14 Check Process ................................................................................................ 76
2.15 Set Program Origin.......................................................................................... 77
2.16 Unload Part ..................................................................................................... 78
2.17 Cutting Table ................................................................................................... 81
2.18 Adjust Travel Path ........................................................................................... 81
2.19 Restore Default Clamps .................................................................................. 81
3
Tools Menu ........................................................................................................... 82

3.1 Edit Tools Library ............................................................................................ 82
3.1.1
Tool Library tab....................................................................................... 82
3.1.1.1 Tool Field.......................................................................................... 82
3.1.1.2 Add Tool to Library ........................................................................... 83
3.1.1.2.1
Common tab ............................................................................ 83
3.1.1.2.2
Allowed station sizes ............................................................... 84
3.1.1.2.3
Close to clamp ......................................................................... 84
3.1.1.2.4
Type Properties ....................................................................... 85
3.1.1.3 Create Tool....................................................................................... 86
3.1.1.4 Tool Table......................................................................................... 87
3.1.1.4.1
Die Selection............................................................................ 87
3.1.1.4.2
Allowed Angles ........................................................................ 89
3.1.1.4.3
Tools Quantity.......................................................................... 89
3.1.1.4.4
Comment column..................................................................... 89
3.1.1.4.5
ToolN column........................................................................... 89
3.1.1.4.6
Tool ID column......................................................................... 89
3.1.1.5 Printing the Library ........................................................................... 89
3.1.1.6 Renaming a Tool .............................................................................. 89
3.1.1.7 Tool Data .......................................................................................... 90
3.1.1.8 Copying Tools from one Library to another ...................................... 90
3.1.1.9 Deleting a Tool ................................................................................. 90
3.1.1.10 Tool Report....................................................................................... 90
Punching Manual
3.1.2
Setup file tab........................................................................................... 91
3.2 Used Tools... ................................................................................................... 92

3.2.1
Setting Stations for Tools ....................................................................... 93
3.2.2
Change Tool ........................................................................................... 93
3.2.3
Tool Data option ..................................................................................... 93
3.2.3.1 Common ........................................................................................... 94
3.2.3.2 Optimization Strategy ....................................................................... 94
3.2.3.3 Reposition Types .............................................................................. 96
3.2.4
Delete Tool ............................................................................................. 96
3.2.5
Make Optimization.................................................................................. 96
3.2.6
Ordering the CAMs................................................................................. 96
3.2.6.1 Ordering by List ................................................................................ 96
3.2.6.2 Ordering by Mouse ........................................................................... 97
3.2.7
Sorting by Stations ................................................................................. 97
3.2.8
Sorting by Type ...................................................................................... 97
3.2.9
Locking Stations ..................................................................................... 97
3.2.10 Die Selection in Used Tools ................................................................... 97
3.2.11 Tool Functions .................................................................................... 98
3.2.12 Group/Ungroup....................................................................................... 98
3.2.13 Turret Setups section ............................................................................. 98
3.3 Create a Special Tool File ............................................................................... 98
3.3.1
Tool Definitions....................................................................................... 98
3.3.1.1 Circular Tool ..................................................................................... 99
3.3.1.2 Rectangular Tool .............................................................................. 99
3.3.1.3 Rounded Rectangle.......................................................................... 99
3.3.1.4 Square Tool .................................................................................... 100
3.3.1.5 Oval Tool ........................................................................................ 100
3.3.1.6 Triangular Tool ............................................................................... 100
3.3.1.7 D Shaped Tool................................................................................ 101
3.3.1.8 Double D Shaped Tool ................................................................... 101
3.3.1.9 Corner Radius Tool ........................................................................ 101
3.3.1.10 Special Tools .................................................................................. 102
3.3.2
Creating User Defined Tools ................................................................ 102
3.3.2.1 Creating the outline of the tool........................................................ 102
3.3.2.1.1
Adding the new tool to the Tool Library ................................. 105
3.3.2.2 The Tool Reference Line ................................................................ 106
3.3.2.3 Testing the New Special Tool......................................................... 108
3.3.3
Names for Special Tool Files................................................................ 109
3.3.3.1 Forming Tools................................................................................. 109
3.3.3.2 Tapping Tools................................................................................. 109
3.3.3.2.1
MM Tapping Tools ................................................................. 109
3.3.3.2.2
Inch Tapping Tools ................................................................ 109
3.3.3.3 Wilson Wheel Tools........................................................................ 110
3.4 Turret Setups................................................................................................. 111
3.4.1
Machine section.................................................................................... 111
3.4.2
Setup File section ................................................................................. 111
xi
cncKad
3.4.2.1 Select Setup File ............................................................................ 111
3.4.2.2 Creating a New Setup .................................................................... 111
3.4.2.3 The LASTSET File.......................................................................... 111
3.4.2.3.1
Creating the LASTSET file..................................................... 112
3.4.2.3.2
Using the LASTSET file ......................................................... 112
3.4.2.4 Save Setup As................................................................................ 114
3.4.2.5 Editing an Existing Setup................................................................ 114
3.4.2.6 Editing the ToolFunc File ................................................................ 115
3.4.2.7 Removing an Existing Setup .......................................................... 117
3.4.2.8 Turret Display ................................................................................. 118
3.4.2.8.1
Station number field............................................................... 118
3.4.2.8.2
Tool Preview .......................................................................... 118
3.4.2.8.3
Tools' List............................................................................... 119
3.4.2.8.4
Functions' List ........................................................................ 119
3.4.2.8.5
Adding Tool............................................................................ 119
3.4.2.8.6
Removing Tool....................................................................... 119
3.4.2.8.7
Changing Tool ....................................................................... 119
3.4.2.8.8
Tool Functions ....................................................................... 119
3.4.2.8.9
Fix Station.............................................................................. 119
3.4.2.8.10 Switch To Setup List .............................................................. 119
3.4.2.8.11 Radial View............................................................................ 119
3.4.3
Multi-Tools section................................................................................ 119
3.4.3.1 Add/Create a New Turret................................................................ 120
3.4.3.2 Edit Turret....................................................................................... 120
3.4.3.2.1
Station Number...................................................................... 121
3.4.3.2.2
Track...................................................................................... 121
3.4.3.2.3
Station Size............................................................................ 121
3.4.3.2.4
Station Angle ......................................................................... 121
3.4.3.2.5
Auto Index.............................................................................. 121
3.4.3.2.6
90 Degrees Only.................................................................... 121
3.4.3.2.7
Round Only............................................................................ 122
3.4.3.2.8
Multi-Tool ............................................................................... 122
3.4.3.3 Remove Turret................................................................................ 122
3.5 Convert Old Boschert Tools .......................................................................... 123
4
NC Program Creation.......................................................................................... 124

4.1 Creating the Program .................................................................................... 124
4.2 NC Generation Stage 1 ................................................................................. 124
4.5.1
Use Macros (Sub-Routines) ................................................................. 126
4.5.2
Automatic Testing of Common Cuts..................................................... 126
4.5.3
Use Controller Compensation .............................................................. 126
4.5.4
Report File Creation Options ................................................................ 126
4.5.5
Update LASTSET ................................................................................. 126
4.5.6
Run Simulation After Post Processor ................................................... 126
xii
Punching Manual
4.5.7
4.5.8
4.5.9
4.5.10
4.5.11
Automatic Detection ............................................................................. 127

Program Number .................................................................................. 127
Sheets Quantity .................................................................................... 127
Sheet Loading ...................................................................................... 127
Name and Path of NC file..................................................................... 128

5
NC Code Simulation and Editing......................................................................... 129

5.1 Opening the Simulation ................................................................................. 129
5.2 Running the Simulation ................................................................................. 129
5.2.1
Starting the Simulation ......................................................................... 130
5.2.2
Pausing the Simulation......................................................................... 130
5.2.3
Stopping the Simulation........................................................................ 130
5.2.4
Simulation Speed ................................................................................. 130
5.2.5
Simulation Time.................................................................................... 130
5.3 Simulation Screen Elements ......................................................................... 130
5.3.1
The State Bar ....................................................................................... 131
5.3.1.1 Snap Button.................................................................................... 131
5.3.1.2 Dim Button ...................................................................................... 131
5.3.1.3 Tool Button ..................................................................................... 131
5.3.1.4 Stop Button..................................................................................... 131
5.3.1.5 Clamp Button.................................................................................. 132
5.3.1.6 OBS Button..................................................................................... 132
5.3.1.7 Cursor Coordinates ........................................................................ 132
5.3.1.8 Program Information....................................................................... 132
5.3.1.9 Line section .................................................................................... 132
5.3.1.10 Tool information.............................................................................. 133
5.3.2
NC Code Editing................................................................................... 133
5.3.2.1 Insert a New Line............................................................................ 134
5.3.2.2 Delete a Line .................................................................................. 134
5.3.2.3 Insert a G Code (Pattern) ............................................................... 134
5.3.2.4 Mark a CAM.................................................................................... 134
5.3.2.5 Send to machine (DNC) ................................................................. 134
5.3.2.6 Send NC to Diskette ....................................................................... 134
5.3.2.7 Searching List................................................................................. 134
5.3.2.8 Find Previous.................................................................................. 134
5.3.2.9 Find Next ........................................................................................ 135
5.3.3
Graphic Simulation ............................................................................... 135
5.3.3.1 Toolbar... ........................................................................................ 135
5.3.3.2 Status Bar Enabled......................................................................... 135
5.3.3.3 Status Bar On Top .......................................................................... 136
5.3.3.4 Beep ............................................................................................... 136
5.3.3.5 Split................................................................................................. 136
5.3.3.6 Zoom Part F5............................................................................... 136
5.3.3.7 Zoom Sheet Ctrl+F5 .................................................................... 136
5.3.3.8 Zoom Window F6 ........................................................................ 136
5.3.3.9 Zoom In F3 .................................................................................. 136
xiii
cncKad
5.3.3.10 Zoom Previous ............................................................................... 136
5.3.3.11 Zoom Out F4 ............................................................................... 136
5.3.3.12 Zoom Realtime ............................................................................... 137
5.3.3.13 Pan Realtime .................................................................................. 137
5.3.3.14 Redraw F2 ................................................................................... 137
5.3.3.15 Mark Line........................................................................................ 137
5.3.3.16 Ask.................................................................................................. 137
5.3.3.17 Show Clamps Bar ........................................................................... 137
5.3.3.18 Fill Tools ......................................................................................... 137
5.3.3.19 Rapid Tool Path .............................................................................. 138
5.3.3.20 Display Bend Lines......................................................................... 138
5.3.4
Measure................................................................................................ 138
5.3.4.1 From Base Point............................................................................. 138
5.3.4.2 Point to Point .................................................................................. 138
5.4 The Tools Menu ............................................................................................ 138
5.4.1
Edit Tools Library.................................................................................. 138
5.4.2
Edit Setup ............................................................................................. 139
5.4.3
Check Stations ..................................................................................... 139
5.4.3.1 Simulation tooling ........................................................................... 139
5.4.3.2 NC tooling....................................................................................... 139
5.4.3.3 Settings and definitions .................................................................. 140
5.4.3.3.1
Change Station for New Tool................................................. 140
5.4.3.3.2
Change Turret Tool................................................................ 140
5.4.3.3.3
Display Mode ......................................................................... 140
5.4.3.3.3.1 All Turret ............................................................................ 140
5.4.3.3.3.2 Used Tools Only ................................................................ 140
5.4.3.3.3.3 Changes Only .................................................................... 141
5.4.3.3.4
Confirm All Turret Changes, Correct NC ............................... 141
5.4.3.3.5
Close, Do Not Update............................................................ 141
5.4.4
Tooling Changes Example ................................................................... 141
6
Appendices ......................................................................................................... 143

6.1 The Report File.............................................................................................. 143
6.1.1
Small Introduction................................................................................. 143
6.1.2
Types of templates ............................................................................... 144
6.1.3
Creating the Template .......................................................................... 144
6.1.3.1 Naming a Template ........................................................................ 144
6.1.3.2 Creating a Plaintext Template ........................................................ 144
6.1.3.3 Creating an RTF Template ............................................................. 145
6.1.3.4 Creating a DOC Template .............................................................. 146
6.1.4
Testing your Template.......................................................................... 146
6.1.5
Tokens in cncKad ................................................................................. 147
6.1.5.1 Common Tokens ............................................................................ 147
6.1.5.2 Additional Tokens ........................................................................... 149
6.1.6
ToolBlockOrder Model Key................................................................... 159
6.1.7
Key Words for Tool List in NC and in Report........................................ 159
6.1.8
Template Examples.............................................................................. 160
xiv
Punching Manual
6.1.8.1
6.1.8.2
6.1.8.3
A plaintext template example ......................................................... 160

An RTF example............................................................................. 161
A DOC Example ............................................................................. 162
6.2 Creating New Functions ................................................................................ 162

6.2.1
The Function's Structure ...................................................................... 162
6.2.2
Making the Function available for cncKad............................................ 162
6.2.3
Adding the New Function in the Code .................................................. 163
6.3 Tool Clearance .............................................................................................. 165
6.4 Repositioning principles ................................................................................ 166
6.4.1
Clamp Avoidance ................................................................................. 166
6.4.2
Repositioning Example Tables ............................................................. 167
6.4.3
Automatic Repositioning for Small Sheets ........................................... 167
6.5 Laser Processing Long Parts ........................................................................ 168
6.6 Wilson Wheel Programming in cncKad ......................................................... 169
6.6.1
Tools..................................................................................................... 169
6.6.2
Programming ........................................................................................ 170
6.6.3
Common Cuts....................................................................................... 171
6.6.4
Customization....................................................................................... 171
6.6.4.1 Customization using Functions....................................................... 171
6.6.4.2 Customization using NCSEC.......................................................... 172
6.6.5
Cutting/Forming Speed......................................................................... 172
6.6.6
The Wilson Wheel Section in the MDL file. .......................................... 172
6.7 Using Sheet Transformation.......................................................................... 173
6.7.1
Processing with a Sheet Transformation.............................................. 173
6.7.2
Sheet Transformation with Reposition.................................................. 174
6.8 The NC to DFT feature.................................................................................. 174
6.8.1
Preparing the GCD file ......................................................................... 174
6.8.2
Loading the prepared NC file................................................................ 175
6.8.3
Creating a drawing (DFT) ..................................................................... 176
6.8.4
Creating a Setup file ............................................................................. 176
6.9 Laser Common Cuts ..................................................................................... 177
6.9.1
Preparing a Geometry for Common Cut............................................... 177
6.9.2
Preparatory Cut .................................................................................... 177
6.9.3
Example................................................................................................ 178
6.10 Additional Options in cncKad's Machine files ................................................ 181
6.10.1 Additions in the MDL file....................................................................... 181
6.10.1.1 New MDL Keys ............................................................................... 181
6.10.1.2 Functions have moved to MDL files ............................................... 181
6.10.1.3 Functions can be used as Pre-Macro or Post-Macro ..................... 182
6.10.1.4 Delete comments from NC ............................................................. 182
6.10.2 Run Out in cncKad ............................................................................... 182
6.10.3 Support for very big arcs ...................................................................... 183
6.10.4 Additions in the TRT files...................................................................... 183
6.10.5 Support for Program Origin .................................................................. 184
xv
cncKad
6.10.6 MDLX per machine file ......................................................................... 184
6.11 Inches users upgrading from previous versions to 7.xx ................................ 184
6.11.1 Values that are per Working Unit.......................................................... 184
6.11.2 Values translated when switching between Working Units .................. 185
6.12 cncKad V.8s new Material List ..................................................................... 185
6.12.1 Introduction........................................................................................... 185
6.12.2 Laser Technology Material List............................................................. 187
6.12.3 Material Lists ........................................................................................ 187
6.12.3.1 Adding Materials to Lists ................................................................ 188
6.12.4 Materials Conversion Table.................................................................. 189
6.12.4.1 Selecting a New Material for the Old one ....................................... 190
6.12.4.2 Use for conversion.......................................................................... 190
6.12.4.3 Convert old laser table for selected materials ................................ 191
6.12.4.4 Using the new list ........................................................................... 191
6.12.5 Changing the Conversion Definitions ................................................... 192
6.13 The cncKad Service Pack ............................................................................. 193
6.13.1 Installing the cncKad Service Pack ...................................................... 193
6.13.2 Working with networked seats.............................................................. 194
6.14 The cncKad Update Manager ....................................................................... 194
6.14.1 What is the Update Manager................................................................ 194
6.14.2 Installing the Update Manager.............................................................. 195
6.14.3 Configuring the Update Manager ......................................................... 196
6.14.3.1 Selecting a download path ............................................................. 196
6.14.3.2 Entering a Customer ID .................................................................. 198
6.14.3.3 Setting the update check interval ................................................... 198
6.14.4 Configuring the cncKad workstation ..................................................... 199
6.15 Configuring your system to send Problem Report......................................... 199
6.15.1 Open the Control Panel ........................................................................ 200
6.15.2 Open the Internet Options dialog.......................................................... 200
6.15.3 Select a default application................................................................... 200
6.16 Multiple Parts with Reposition ....................................................................... 201
6.17 Punching a Perforated Sheet in cncKad ....................................................... 203
6.17.1 Creating a Perforated Sheet................................................................. 203
6.17.1.1 Sheet Dimensions .......................................................................... 204
6.17.1.2 Perforating the Sheet...................................................................... 204
6.17.1.3 Perforated Sheet example .............................................................. 205
6.17.2 Punching a Perforated Sheet ............................................................... 205
6.17.2.1 Using Auto Punch........................................................................... 205
6.17.2.2 Optimizing the Path ........................................................................ 205
6.17.3 Testing the Optimization....................................................................... 206
6.18 Installing and Using the NetHASP................................................................. 207
6.18.1 Installing the NetHASP on the License PC........................................... 207
6.18.1.1 Installing the NetHASP utilities ....................................................... 207
6.18.2 Using workstations with the NetHASP.................................................. 207
6.18.2.1 Setting the NetHASP.ini file ............................................................ 207
xvi
Punching Manual
6.18.3 HASP FAQ ........................................................................................... 208
6.18.3.1 What is Error 129?.......................................................................... 208
6.18.3.2 Cannot run cncKad with NetHASP connected directly................. 208
6.18.4 How do I know on which computer the License Manager is running?.. 209
6.19 Creating a Trimmed Sheet ............................................................................ 209
6.19.1 Why Trim a Sheet................................................................................. 209
6.19.2 Creating the initial part.......................................................................... 209
6.19.2.1 First Nibble ..................................................................................... 209
6.19.2.2 Second Nibble ................................................................................ 209
6.19.2.3 Current Part View ........................................................................... 209
6.19.3 Defining the Sheet ................................................................................ 210
6.19.4 Defining the Common Cuts .................................................................. 210
6.19.5 Using Explode Multiple Part ................................................................. 211
6.19.6 Deleting extraneous punches ............................................................... 211
6.19.7 Setting the Trimming ............................................................................ 211
6.19.8 Adding Chute commands ..................................................................... 212
6.19.9 Adding more parts to the Sheet............................................................ 214
6.19.10 Setting the tools order.......................................................................... 214
6.20 Changing Turret Numbering.......................................................................... 215
6.21 Re-Enabling the DOC Report Addin.............................................................. 216
6.22 Release Notes for BOSCHERT users........................................................... 216
6.22.1 Boschert Tools...................................................................................... 217
6.22.1.1 Working with new setup file ............................................................ 217
6.22.1.2 Adding tool to machine ................................................................... 217
6.22.2 ToolN setting in Tool Library................................................................. 217
6.22.3 Defining Tools' Angle............................................................................ 217
6.22.4 Setting the Machine Version Parameter............................................... 218
6.22.5 Offsets for Repeated Functions............................................................ 218
6.22.6 Plasma / Roller / Engrave..................................................................... 218
6.22.7 Converting Plasma.bin to cncKad Laser Tables................................... 219
7
Index ................................................................................................................... 220
xvii
cncKad
xviii
Punching Manual
Introduction
cncKad is an NC code generator for CNC Punch and Laser machines. In this
manual we will be covering the use of cncKad by punching machines
The cncKad modules include a complete set of tools to aid you in creating the
optimal program for your machine. Some of the functions included are listed below:
CONTOUR CREATION: The contours of the parts that you want to cut can be
created either graphically by the user, with the aid of cncKad, or by importing
a file from another drafting package (See the Punch Tutorial for a full
description of this module).
GRAPHIC PROGRAM DEFINITION: Graphic interaction with the user that
enables defining the desired CAM process, including the setting of all
program options.
PROGRAM GENERATION (G-Codes Post Processor): Automatic generation
of CNC programs. cncKad supports a very wide range of controllers and
CNC languages.
FILE EXCHANGE: cncKad supports import of files in DXF, Iges or Cadl
format from other drafting packages.
PROGRAM ARCHIVING: Sorted directories of CAM processed drawings,
drafts and CNC programs, for backup and retrieval.
This current version of cncKad is intended for use on Windows2000, Windows XP
and Windows Vista workstations.
cncKad includes five modules:
Drafting
CAM placement (processing)
Nesting
Simulation
DNC (communication to machine)
cncKad
1 Punch Manual
From this menu you can place the actual punches on your part. There are two
options for placing punches on your draft, adding a Single Punch, or using Auto
Punch, and several options for defining your CAMing:
1.1
Add Punch
You can also click the Add Punch button
from the Common Toolbar

.
The following dialog will appear:
1.1.1
Single Punch
Adding single punches to your part will place one instance of a selected tool at a set
position. A single punch can be a hole in the sheet or a punch on a contour.
There are several ways to add single punches to your geometry, the one that you
choose depends on the cut you need.
Single punches are selected by clicking the Single option in the punch type area.
The precise type of punch can be selected from the Single Type dropdown list:
Punching Manual
All single punches visible on the drawing are marked with hatched lines.
1.1.1.1
Single
With this option the user will be able to add a single punch to a specified entity. After
selecting the single option, click the entity on the drawing that you wish to punch. It
will be punched using the currently selected tool.
If you are punching a circle place the cursor near the contour of the circle and click
the mouse button. Dont try to fit the punch outline into the circle. The tool selected
does not have to fit exactly to the hole to be punched.
When a single punch is placed on the part, it is defined as the tool shape filled with
hatch lines.
If you selected a line entity for punching, the placement of the punch on the line will
depend on the option selected from the Tool Positioning dropdown list. For more
information on this option, see the Tool Positioning section of this chapter.
1.1.1.2
On Line
This option will punch all the entities that lie on the same line at equal distances.
The user is required to locate two entities that lie on the line. cncKad will take the
angle and the distance between the two points and will search for more holes which
were placed at the same angle and distance. Selected holes will be punched with the
current tool. If the Auto Tool option is checked, the cncKad will select the
appropriate tool from the Tool library.
Depending on the type of controller that your machine has, the NC code will differ for
this command. For instance with Fanuc controllers, the created code will be G28.
cncKad
1.1.1.3
On Arc
This option will punch all the entities that lie on the same radius, with the same angle
between them.
The user is required to locate three points on the circumference of the arc, the
cncKad will then check if there are any more holes on the same radius and the same
angle between them. All selected holes will be punched with the current tool. If the
Auto Tool option is checked, cncKad will select the appropriate tool from the tool
library.
Depending on the type of controller that your machine has, The NC code will differ for
this command. For instance with Fanuc controllers, the code issued will be G29.
1.1.1.4
In Window
This command will punch the selected closed contours that fall within a user defined
window, providing they are either Squares, Circles or Ovals. If the Auto Tool option
4
Punching Manual
is not checked, the cncKad will only punch contours that fit the currently selected
tool. If checked, all the contours that have suitable tools in the tool library (or the
Setup File, whichever is chosen) will be punched.
Contours that fall only partially within the boundaries of the window will also
be punched (if they conform to the above mentioned shapes).
1.1.1.5
Punch All
This option takes all the closed contours on the part and punches them with the
appropriate tool, when the Auto Tool option is checked. If it is in the manual mode,
only contours that fit the currently selected tool will be punched.
1.1.1.6
Punch Free Hand
With this option, the user can freely punch with the currently selected tool, anywhere
on the part.
When this option is selected, an Angle field is opened: it allows the user to enter the
angle for the punch placement.
1.1.1.6.1
Dynamic Angle Change
There is a function for single free hand punches, which allows for dynamical change
increasing or/and decreasing the angle of the tool we want to punch with. All you
have to do is to press on your keyboard the "+" button, in order to increase the angle
of the tool or "-" button, to decrease it.
1.1.1.7
On Punched Entity
With this option, operate a split on an already Punched Entity and place a Single
Punch. While placing it you can define two values: an Offset from the beginning of
the Entity and the Distance separating the new Single Punch from the Existing
Punch.
For the following example,
cncKad
a Single punch on a Punched Entity will look like the following:
1.1.2
Nibble Entity
This command will nibble one selected entity. Select a tool to nibble with, define the
positioning of the tool on the entity, define the spacing (if needed) and click the OK
button to close the punching dialog. Choose a line entity you wish to punch and click
the near one of its endpoints. The endpoint that is nearest to your selection point will
be defined as the starting point. If you have defined offsets, the first offset distance
will be from this endpoint.
1.1.3
Nibble Chain
This command will nibble, with a selected tool, a chain of entities. For this command
to work, all the entities in a chain must be connected at their endpoints.
When selecting a tool to cut a chain of entities, you must select a tool that can cut at
different angles. This means that if you select a rectangular tool, that tool must be in
an index station, or at an angle that fits the desired cut.
Select a tool to nibble with, define the positioning of the tool on the entity, define the
spacing (if needed) and click the OK button to close the punching dialog. Next locate
and click with the cursor the first entity in the chain, and then the last one. These two
entities and all those in between them will be punched.
1.1.4
Nibble Contour
This command nibbles a closed contour. The contour can be made up of lines and
arcs, the end points of the entities must be touching.
spacing (if needed) and click the OK button to close the punching dialog.
6
Punching Manual
Select an entity on the contour and the contour will be punched.
1.1.5
Nibble Start-End
This command will nibble entities that are not connected with each other, lying along
the line.
spacing (if needed) and click the OK button to close the punching dialog. Select the
first entity and then the last one, as shown below. As you can see, all the entities
lying on the same line will be punched.
1.1.6
Crunch
This command works on closed contours of circular areas. On rectangular areas it

works also on open contours.
Select an appropriate tool for crunching with. If you are crunching a rectangular area
you should use a square or a rectangular tool and if you crunch a circular area you
should use round tools.
Define the offsets, if any, and click the OK button to close the punching dialog.
Click with the mouse cursor next to one of the corners (entity's endpoint) of the
rectangular shape to be crunched, e.g. the bottom left, and then select the
perpendicularly opposite one, e.g. top right. The area in between will be punched.
When you want to crunch the circular shape, just choose the proper tool and click the
area you want to be punched.
The following shows crunching of a circular hole:
cncKad
The below example shows crunching of the outer contours between two parts:
The same way this option can be used to crunch material between any two
perpendicular points.
1.1.6.1
Crunching a notch with one tool
This feature makes it possible to punch two adjoining entities of the notch with one
tool equal or bigger than a notch. This can be done with the aid of Crunch option. On
the picture below you can see the 20mm notch punched this way with RE 30 tool.
Punching Manual
1.1.7
Crunch Right-Angled Triangle

This option only becomes available for Square tools. If you will choose and
try using any other tool type you will be presented with the following
warning:
.
This option enables you to crunch a triangular geometry only if there is a 90 degree
angle.
After selecting this option in the dialog, you must choose the starting point for the
crunch, (the Status Bar will show the following:
).
Now choose the opposite end point (the Status Bar will show the following:
).
The area between them will be punched.
1.1.8
Crunch Chamfer
This option enables you to crunch a Chamfered Entity, and it can be done with
Square, Rectangular, as well as with Double-D tools:
cncKad
1.1.9
Crunch Arc
This option enables you to crunch an outside Arc. This can be done only with round
tools:
1.1.10
Punching Grids
This command creates an array or grid of punches. When selecting it, the following
area of the punch dialog is activated.
There are four options in the grid dropdown list:

Snake X
10
Punching Manual
Snake Y
Uni-direction X
Uni-direction Y
The difference between these options is the way (Snake, Uni-direction) and the
direction (X, Y) in which the grid will be punched.
Creating a Grid:
Select the Grid option and select the tool that you wish to punch with.
Define the amount of punches in the X and Y directions.
Define the distances between the punches. The distance is defined from the
center of each punch to the center of the next punch.
Click the OK button to close the punch dialog.
Locate the entity on which the first punch of the grid will be placed.
The grid can be deleted by selecting the first punch in the grid.
1.1.11
Choosing a Tool
Pressing the Tool button, from the Tool Section of the Add Punch dialog, you will be
redirected to Tool Selecting dialog, where from Tool Library and Setup File tabs you
will be able to choose desired tool for processing entities with.
1.1.12
Tool Positioning
Before positioning the punch, the user must define two parameters:
The Side of the punch:
The Side Button can be found on the State Bar, on the left side of the
screen; there are three options which define how the tool is placed in relation
to the line, arc, or circle selected for punching:
o Side the edge of the punch will be placed on the side of selected entity.
o Tip the center of the punch will be placed on top of the line.
o Auto the punch will be placed automatically on the correct side of the
entity. Before activating this option, make sure to run the contour
recognition checks on the current part, so that the program would
recognize the difference between holes in the part and sheet metal and
would know on which side of the contour to place a punch.
The Index definition:
The Auto Index button can be found on the State Bar, and has two states:
o On In this state, the currently selected tool will rotate itself to the angle
of the line selected. This is only for machines that have Auto Index
11
cncKad
stations (rotating stations). There are usually only a few rotating stations
on most machines, therefore you should be careful not to use more
rotating tools than you have stations for.
o Off In this state, the tool will be placed on the selected line at the angle
that was defined, for the tool within the tool library. If this angle is incorrect
for the line selected, a warning will appear giving the user the option to
cancel the punching procedure or to continue.
After defining all the above parameters, from the dropdown menu choose the
Positioning for your punch:
1.1.12.1
Offset
This option gives you an opportunity of offsetting the tool from the edges of the
entity, of the part (rectangular block) or of the sheet, by a given distance (from Start
and End dropdown lists you can choose one of the options).
You can set the Start value of the offset for instance from the end of the entity and
the End value for the end of the part.
The Start and End dropdown lists are available for Nibble Entity, Nibble
Start-End, Crunch and Crunch Chamfer options.
The offset distance values are defined in the offsets Start and End fields within the
Tool Positioning section. They can be positive or negative. If the value is negative,
the punch will be placed in from the start of the chosen element, if it is positive it will
overhang from line's end.
The second offset value (End) is used for nibbling and crunching of non
restricted spaces. Therefore for single punches, crunch triangle and
grid options there will be only one offset value field available.
Entering a negative offset value can be used for creating Micro Joints between parts.
The following are examples of different offsets:
12
Punching Manual
- i.e. "-2", in the offset field
1.1.12.2
Entity's End
With this option, the center of the tool will be placed at the endpoint of the line. This is
done automatically with no need for any additional parameter input.
1.1.12.3
Tool's End Tangent
Using this option will place the end of the tool tangent to the end of the line. This is
equivalent to Offset = 0.
1.1.12.4
Next Entity's Tangent

This option is useful for round and oblong tools.
This option will place the tool tangent to the next entity in a chain of entities. The
endpoints of the entities must be connected.
1.1.12.5
Centered
This option will place the punch on the center of the line selected. It doesn't matter
where you select the line, the punch will always center itself on the line.
1.1.12.6
On Shape Center
This option will place the shape of the tool exactly in the middle of the shape (NOT
entity) we want to punch.
13
cncKad
This way we will be able to process a hole with a tool that is not an exact match, and
the punch will be still placed in the holes center, e.g. an oval hole of 31 by 10
processed with an OB 30 10 tool:
This option works only for standard shapes Rounds, Squares,

Rectangles, Ovals, Rounded Rectangles and Single/Double D.
1.1.13
From Base Line
This option is available for Crunch and Crunch Chamfer Punch Types.
Marking this checkbox allows you for crunching nonstandard notches, of an angle
larger than 90. This means that the offsets set for the crunch will be measured from
the Base Line of the notch.
This option is unavailable for Crunch punch type for which scallop type of
Tool Spacing was selected.
1.1.14
Tool Spacing
The Tool Spacing options define how much overlap there will be on the tool when
nibbling.
1.1.14.1
Overlap Definition
When the overlap is defined as 0%, the current tool will arrange itself on the contour
with the minimal overlapping. If you choose to nibble an entity with a tool that is
longer than one and a half times the length of the entity, you will receive a warning
(provided you have marked the appropriate option in the Punch and Cut Warnings
of the Workspace Settings dialog in Drafting and Nesting Manual). Clicking OK
button will nibble the entity, clicking Cancel button will annul the operation, and the
entity wont be punched.
See the examples presented below. The punches here were made with 0% overlap:
The following case produces no warning because it is a correct procedure:
14
Punching Manual
The following case will produce a warning because more than half the punch
is overlapping:
When the overlap is defined with a percentage other than 0, the tool will be
overlapped by that percentage. This can be used for cutting arcs and circles. The
greater the overlap, the smoother the cut will be. See the following two examples:
Cut defined with 0% overlap.
Cut defined with approximately 75% overlap.
If you define an overlap that has a step less than the sheet thickness, you
will receive a warning (as before, only if you mark this option in Punch
and Cut Warnings).
1.1.14.2
Step Definition
With this option the distance between the centers of each punch in a nibbling cycle,
is defined. If a distance, that is less than the sheet thickness is defined, a warning will
be received.
15
cncKad
1.1.14.3
Scallop Definition
This option is accessible only when a circular tool is being selected. The scallop is
the height of the tooth that is left between the punches of a circular tool. See the
following picture:
1.1.15
Tool Sequence
Here the user can set the sequence of the tool.

For more information on this function go to Set Tool Sequence section of the CAM
Menu chapter of this manual.
1.1.16
Use Tool Data
With this function you will be able to utilize any special features assigned to a certain
tool. Here you can view and edit chosen tool's data add a comment, choose the
station for it and define whether it should be used as Close to Clamps tool or not.
In this example we will view the Tool Data of a Wilson Wheel Louver tool:
Special tools have one more option Type Properties tab. Clicking it will enable you
to define specific parameters for a punch made with the tool you chose:
16
Punching Manual
This means that for every punch you place on your part with this tool you can use
different settings.
1.1.17
Directional Punch option
Choosing this option will add a direction to your punching. When you place the punch
on a part, clicking the entity endpoint, you will see that a blue arrow (or a red one
depending on the background you are working on) was added to the beginning of
your placement, showing a direction the punch was made in.
1.1.18
Punch as Singles
This option concerns Nibbling and allows the user to execute the Nibble as Single
Punches. Thereby, each punch will get a separate line in the NC code.
1.1.19
Wheel Connect
This function is available, when the Wilson Wheel Tool is currently chosen.
If this box is checked, the Wilson Wheel will process the part's contour continuously
(without stops, which it usually does) it will connect between one punch and the
next one.
By default this option is checked for all nibbling types, except for nibble
entity.
1.1.20
Functions button
This option allows you to access the Functions for Selected CAM dialog directly
from the Add Punch dialog.
1.1.21
Stop or Push Out
This command is for machines that have a chute on the table. Parts that have been
punched/cut out of the sheet can be pushed out via the chute. This prevents from
having to use a Stop Machine command, in order to remove the part. The position of
the chute varies from machine to machine.
See full explanation in the Push Out (Chute) section of CAM Menu chapter in this
manual.
1.1.22
Wire Joint
Choosing this option (by checking the Perform box) you will be allowed to place
Wires as an integral part of the Punch.
17
cncKad
You can set the width of the Wires (W) as well as the maximum distance between
them (ML), and they will be integrated into the Punch, without splitting the entity
being punched:
Choosing one of the After First Hit and Before Last Hit options enables creating
Wires after the first and before the last punch. They address the issue of rounded
corners when punched by round tools.
After placing the punch, you can return and Edit it (clicking on the Edit CAM icon
from CAM Toolbar) changing the parameters, without having to edit several
entities (as it would happen with regular Micro Joints that have been placed after the
entity has been punched).
1.1.22.1
Width
This parameter sets the width of the Wire joint(s) placed for this punch.
1.1.22.2
Max Length
This option is very useful when the precise position of the Wire joint(s) is not
important. This parameter sets the maximum distance between two Wires, and NOT
the position relative to the entitys end.
If you define a Max Length of 80 for an entity with a length of 100, this does not
mean that there will be a Wire at 80mm from entitys beginning. The exact position
will depend on the tool chosen for the punch the Wire will be placed at tool's Hit
Boundary.
Below there are two punches defined with a Max Length of 80:
The punch on the left was made with an RE 50 5 tool and the Wire was placed 50mm
from the entitys beginning.
The one on the right was made with an RE 20 10, and the Wire was placed at 60mm.
(These Wires were made with a Width of 5 for demonstration purposes.)
1.1.22.3
At Least One
This option is very useful when you want to place just one Wire more or less in the
middle of a punch, and the exact position is not important:
Set the Width at the desired value, and the Max. Length at a very large value (larger
than possible, such as 10000).
18
Punching Manual
The result will be one Wire positioned the tool Hit Boundary nearest the middle of the
entity being punched.
1.2
Auto Punch
By using this feature you allow the program to punch the whole part automatically.
You can also click an icon

. The following dialog will appear:
1.2.1
Auto Punch Parameters tab
On this tab you will be able of defining optional settings for automatic processing of
the part.
Auto Punch will only work on closed contours and viable entities, so before using
this feature we would recommend to run a Check. Even if there are some bad
contours, this will not prevent processing the correct ones.
There are two options for running Auto Punch:
o Auto will run Auto Punch for the whole part.
19
cncKad
Single will use Auto Punch on a selected entity. This option will punch
just one entity at a time. But when you want to punch next entity you don't
have to come back to this dialog. All you need to do is just to click the
cursor next to it and it will be punched.
See the subsequent sections for explanation on all the features which can be found
on this tab.
o
1.2.1.1
Tool Spacing Defaults
These options address the issues discussed in Scallop Definition topic of the Tool
Spacing section of this chapter.
The value in this section is given in millimeters or inches, depending on your
machine and the option you chose from working units section of Settings Menu
chapter of Drafting and Nesting Manual.
1.2.1.1.1
Minimum Tool Overlap
Select a desired minimum Overlap to be used when tool overlap occurs.
1.2.1.1.2
Scallop for Round Tools
Here the user can enter the value of Scallop size, which will be implemented for
round tools.
1.2.1.2
Cutting Tools Restrictions
In this section some limitations for the tools can be set.
1.2.1.2.1
Minimum Width
When punching the outer contour, use tools of no less than this width.
1.2.1.2.2
Maximum Width
When punching the outer contour, use tools of no more than this width. Use this
parameter, to prevent the material waste on the outer side of contour.
1.2.1.3
Tool Selecting Preferences
Choose a strategy for selecting the tools. Move the slider between these two poles
and set the proper option, using your judgment based on the situation.
1.2.1.3.1
Best Tools
Use as many tools as it is necessary (up to maximum quantity of tools that can fit the
turret), in order to achieve best punching results.
1.2.1.3.2
Minimum Tools
Try, as much as possible, to re-use tools. This reduces efficiency.
1.2.1.4
Odd hits, then Even hits
Select a strategy for the last punch in the middle:

Never dont ever place the last punch in the middle.
Always always, in every case, place the last punch in the middle.
Choose an option between these two poles, based on the situation.
1.2.1.5
Punching scope
You can choose which range of entities will be punched.
1.2.1.5.1
20
Holes
Punching Manual
If you enable this option, the holes in your part will be processed, in accordance with
the settings in the Holes tab.
1.2.1.5.2
Notches
If you want that all the notches in your part would be processed while running Auto
Punch, you need to activate this option by marking the checkbox. Otherwise the
Notch section will not be active and you won't be able to edit any of the following
options:
Perform crunches Selecting this checkbox will allow for automatic
crunching the notches of the part; otherwise each entity will be processed
separately. There are three types of notches that may be processed by Auto
Punch: Corner Notch, Corner with Chamfer, and Right Angle Triangle
Notch. See the below picture:
Checking this option enables editing of the Maximum crunch tool ratio and
Minimum Offset features:
Maximum crunch tool ratio You can define maximum ratio between Width
and Height of the tool that will perform the crunch. If you dont care much
about this option set large number like "80"; if you want that a hole will only
be crunched with a square tool set "1".
Minimum Offset Use this parameter to create an offset for the processed
notch. The actual offset will depend on the tools and strategy chosen for
processing the notch. Its value will be measured from the part's bounding
rectangle, not from the contour edge of the notch.
o
o
a the part's outer contour.

b and c the slitting.
21
cncKad
d the bounding rectangle
In this case, a Maximum Offset of 0 will mean that the arc (q) cannot be
processed!
Maximum Offset This parameter will be used as a maximum the actual

offset will depend on the tools and strategy chosen for process the notch.
1.2.1.5.3
Slitting
If you enable this option, all the outer contours of your part will be processed.
1.2.1.6
Use Tools Library
This option will allow Auto Punch to process the parts on the sheet, using any fitting
tool from the tool library.
This setting DOES NOT apply to processing Holes. When you want that the
holes would be processed using Tools Library, you need to set this
option on the Holes tab.
1.2.1.7
Use Setup File
This option will make Auto Punch to use only tools from the selected setup file (any
tools you have already added yourself to the part, will remain).
You can select the appropriate setup file with the Select Setup button.
This setting DOES NOT apply to processing Holes. When you want that the
holes would be processed using Setup file, you need to set this option
on the Holes tab.
1.2.1.8
Select Setup
Clicking this button you will be moved to the Turret Setups dialog of the Tools Menu.
There you will be able to choose the setup file you want to use for processing the
current sheet.
1.2.2
Holes Tab
Use this tab to define how holes will be processed by Auto Punch:
22
Punching Manual
1.2.2.1
One Hit Only With matching Tool
Checking this option means that all holes will be processed with single punches.
Holes that cannot be punched in this way, will be left unprocessed.
This option disables the Crunch option.
1.2.2.2
Tolerance Settings
In the following window it is possible to set tolerance for punching with specific tools.
This means that by checking Active box and entering a value in either positive or
negative column by the particular shape, the user will be able to punch holes whose
size does not exactly match the size of the tools he possesses.
23
cncKad
For example: If you have a hole with a 3.1 diameter and only a RO 3 tool, you can
define a negative Tolerance (in "" column type positive value) of 0.1, and when
running Auto Punch, the RO 3 will be used. If on the other hand you have a hole of
9.5 diameter and have no exact fitting tool, but only a RO 9.6 tool, set the positive
value (in "+" column type positive value) of tolerance to 0.1 and when running Auto
Punch the RO 9.6 tool will be used.
Keep the Active row checked for all Shape types, unless you do NOT want
a specific type to be processed.
1.2.2.3
Crunch
This option is used for setting the maximum size of rectangular holes that will be
crunched, by entering their width and length in the appropriate fields.
1.2.2.4
Wire Joint
These parameters define how to place Wire joints when processing holes.
For an explanation about how to set the size of the Place Every parameter, see the
Wire Joint section in the Add Punch dialog.
Regardless of the settings defined here, Auto Punch will place at least one
wire on the long sides of rectangles, to ensure they remain attached to
the sheet.
1.2.2.5
For Holes
Selecting one of these options you define the source from which the tools will be
taken for processing holes:
Use tools library this option will allow Auto Punch to use any tool from the
tool library.
Use setup file this option will force Auto Punch to use only the tools from
the setup file chosen in the Auto Punch Parameters tab.
1.2.2.6
Automatic Detection
In this section, you can order the Auto Punch process:

1. Not to detect groups of single punches no group detection will be
operated.
2. To automatically detect lines of single punches cncKad will detect
automatically a line of single punches and turn their type into a "single; on
line".
3. To automatically detect grids cncKad will recognize grids of singles and
will change their punch type into a grid.
The advantages of this option are the shortening of the NC code, but also the
widening of edition possibilities for entities within cncKad: for instance, a punched
grid will be shortened or extended more easily.
If you are not interested in activating this option while using the Auto Punch
feature, you can still define Automatic Detection for the NC code via
the NC Program Creation => Post Processor Options dialog. In this
case, the part will contain singles but the NC will contain "single on line"
punches and grids.
1.2.3
Slitting tab
On this tab you can define various aspects of automatic placing of Micro Joints on
the processed entity.
24
Punching Manual
1.2.3.1
Micro Joint Parameters Section
Here you have the possibility of setting various parameters for placing Micro Joints.
They will be enabled only after you check the Apply Micro Joints box.
1.2.3.1.1
MJ Width
In this field you can set the general width of the Micro Joints to be created.
1.2.3.1.2
MJ Width at Sheet Edge
In this field you can set the width of the Micro Joints to be created on the sheet
edge(s).
1.2.3.1.3
MJ on corners
There is an option of automatic setting the Micro Joints on the corners. This can be
achieved in two ways:
On One Edge:
1.2.3.1.4
On Both Edges:
Every corner
Marking this checkbox you choose to place the Micro Joints on each corner of the
part. But choosing this function disables the usage of The Minimal number of Micro
Joints for this part option.
25
cncKad
1.2.3.1.5
The Minimal number of Micro Joints for this part
As the topic says, from the dropdown list you can select the minimal quantity of the
Micro Joints to be placed on the current part.
1.2.3.2
Wire Joints Parameters Section
The options of this section will be enabled only after you check the Apply Wire
Joints box.
Here you can define parameters such as the width of the Micro Joints (W) as well as
the maximum distance between them (ML).
1.2.4
Shapes Tab
From this dialog you can create special treatment for particular cases by creating
Profiles, and using Predefined Shapes:
1.2.4.1
Special Punching Section
This section presents the options of special punching of untypical sized round holes.
1.2.4.1.1
Profile
A Profile is a set of instructions telling how specific holes will be punched.

You can use the dropdown list to select which from the available profiles you want to
use. If there are none, use the New button to create a new one, and the Delete
button to delete an existing one.
In our example we created a profile called Customer A, in which we have three
round holes of atypical sizes. From the Shapes table let's take a round shape of 4.44
diameter and in the Tooling table let's add the tools we want to process this hole
with and set them in desired sequence. See the below picture:
26
Punching Manual
After running Auto Punch each circle with a 4.44 diameter will be punched with the
sequence of tools we just have set first RO 3.5, then a Pre-tapping tool, and last a
Tapping tool.
Our hole processed with this sequence will look this way:
1.2.4.1.2
Shapes
In this table we can see various shapes that are specified in the current Profile.
When a specific shape is selected, the tooling sequence defined for it appears in the
Tooling section of this dialog.
button to add a shape to the profile, and the
You can use the
delete a shape from the profile.
1.2.4.1.3
button to
Tooling
This table shows the specific tooling sequence set for the item selected in the
Shapes section of this dialog.
You can use the
list.
1.2.4.2
button to add a tool to the list, and the
to delete it from the
Predefined Shapes Section
After saving some specific shape, together with its process, as predefined one (see
the Save As Predefined Shape section of this chapter) this section allows you to
add such a predefined shape to the list:
27
cncKad
After clicking Auto button all the Predefined Shapes from this table will be used to
punch suitable notches and contours of the part. If there are neither suitable notches
nor contours, the Predefined Shapes won't be used.
1.2.5
Punch and Cut Warnings Tab
The following dialog is displayed:
1.2.5.1
Do Not Allow Over Tonnage
Will not allow punching if a tool exceeds the Tonnage Limit of the machine. If the
over tonnage will be detected, the following warning will appear on your screen:
Here, as well as in the subsequently described other processing warnings dialogs,

you will be able to decide about the action to be taken you can choose not only
whether continue the CAM or not, but also you will be given the possibility of
choosing a default option for the similar situation in the future.
To do so, check the Do not ask again this question box, and click one of the
buttons. From now on, depending on your answer, cncKad will or will not process
the entity, when there will be a danger of over tonnage will be detected.
The action undertaken, chosen from the warning dialog, will be the case for
the current part only and as long as you do not re-run cncKad.
1.2.5.2
Do Not Allow Punch Destroys Part
Will not allow punching if a punch will destroy the part. cncKad identifies also when
the punch destroys the part for D, double-D, Cross and Special Tools.
If in the Workspace settings on the Punch And Cut Warnings tab a proper option
will be checked, a warning will be issued whenever Punch will destroy the part:
28
Punching Manual
1.2.5.3
Do Not Allow No Station for Tool

The warning appears only during NC creation.
This option will not allow placing a punch on the part if there are not enough stations
on the turret needed for placing the tools for this punch.
1.2.5.4
Do Not Allow Over Travel in Y

The warning appears only during NC creation.
This option will not allow placing a punch if the tool cannot reach the point to be
processed from where it sits in the turret.
1.2.5.5
Do Not Allow Punch Less than 1.5 Tool
This option will not allow placing a punch if the size of selected nibble or crunch is
less than 1.5 times the tool size.
1.2.5.6
Do Not Allow Punch Step Less than Thickness
This option will not allow placing a punch, if the tool's step is less than the materials
thickness. It will not allow for punching also when during using Single punching the
tool is smaller than the thickness.
1.2.5.7
Do Not Allow CAM in Clamp Dead Zone
Will not allow placing a punch in a clamp Dead Zone.
1.2.5.8
Do Not Allow CAM is out of X working Range
Will not allow placing a punch outside the table limits.
1.2.6
Punching sheet edge
The Auto Punch checks if the Automatically remove punches on sheet edge box
is selected on the Post Processor Options tab of Workspace Settings. If yes, then in
all cases where the part is placed at the sheet edge, the sheet edge won't be
punched; if no, the sheet edge will be punched.
1.3
Deleting Punches
There are three methods for deleting punches:

Press Alt+F3 keys.
From the Edit menu select the Delete CAMs option.
Click the Delete CAMs icon
from the Delete Toolbar
Use the standard Selection options to choose punches for deletion, and click Enter
to confirm the selection; it is recommended you click Redraw icon
clean the draft after completing the deletion.
in order to
29
cncKad
1.4
Set or Clear Last Hit on Center
When crunching or nibbling, you can set the order of punches so that the last punch
in the nibbling process will be in the middle.
1.5
Directional Punch
A directional punch is a cut that is defined to punch in a specified direction. This

option may be used for tool technological reasons as well as for optimization
reasons.
1.5.1
Uni Directional
This option is used for making a punch directional:

Click the punch that you want to make directional.
A red X will be placed at the starting point of the cut and you will be asked if you wish
to reverse the direction of the punch, reply Yes or No and the dialog will be closed.
A blue arrow (or red one depending on the background you are working on) will be
placed on the punch showing the direction that the cut will be made in. No
optimization will change the direction of the cut.
You can continue and select more cuts and make them directional:
1.5.2
Bi Directional
This option converts a directional punch to a punch with no specified direction,

meaning that during the post processing stage the direction of this punch will be
determined.
Click the punches that you wish to make non-directional.
Press Enter when you have selected all the cuts to change to non-directional.
1.6
Save As Predefined Shape
This feature enables you to define a specific shape with its punch(es), which will be
recognized by cncKad and processed automatically with predefined tools assigned
to it, after you run Auto Punch.
After choosing this option, click on chosen punch, and save it.
Then go to the Shapes tab of Auto Punch dialog, create new profile (or choose an
already existing one) and in the Predefined Shapes section, clicking on the asterisk
sign, choose the name of the file(s) you want to use.
30
Punching Manual
2 The CAM Menu

This menu deals with all matters pertaining to the manufacturing process, from
placing the CAMs on your draft to various definitions governing the actual machining
of the part.
2.1
Setting Offsets
These options allow you to create Offsets or edit existing ones.

Changes may produce technological warnings.
2.1.1
Edit Offsets
After you have drafted your part and placed CAMs on it, this option allows you to
choose a specific CAM and define an Offset for it.
Choose this option from the menu, and click the CAM you wish to offset. The
following dialog will open:
31
cncKad
Define appropriate Offsets from the ends of the entities, and click OK button.
2.1.2
Set Offsets
With this option, first you define the Offset you want to set,
and then click the CAMs you wish to apply it to.
2.1.3
Set All the Offsets
This option allows you to change a previously defined Offset.

For example, if you have defined five punches with an Offset of "-5", and now you
want to change all of these Offsets to "-2.5", this option lets you do this with one
command.
After you choose this option, the following dialog will open:
Old here type the value of existing Offset.

New here type the value of the offset you wish to change the previous one
into.
If you define Old as "0", it will change all the punches without any Offset.
2.2
Change Tool for Existing Punches
Select this option after choosing a tool in the Used Tools List of the State Bar. The
following dialog will appear:
32
Punching Manual
Here the user will have the possibility of assigning one new tool for all the selection.
Choose the new tool, and confirm your choice clicking OK button. Then, on the part,
click all the CAMs you want to apply this tool to.
2.3
Edit CAMs
This option allows you to edit the tooling on an already processed entity.
After you choose this feature from the CAM menu, click the CAM you wish to edit. A
dialog, presenting its settings, will open:
33
cncKad
34
For punching:
Punching Manual
For cutting:
As you can see, not all of the CAM parameters are open for editing you cannot
change, respectively, the Punch, the Cutting Types, the Offsets, Cutting Direction
and a few more settings.
2.4
Add MicroJoint
This option is also accessible by clicking the

button from the CAM Toolbar.
Micro Joints are small bridges of material that are left to make connection between
different parts on a sheet, in order to prevent them from falling into the machine.
There are two options for adding a MicroJoint:
35
cncKad
2.4.1
MicroJoint
This option allows adding MicroJoints at the ends of entities. The parameter entered
here is in fact an equivalent of the Offsets field of the Add Punch dialog. In other
words using this option is in fact editing the punchs offsets.
The following example shows an entity to which one's end a MicroJoint had been
added (with the setting shown above). The Edit CAM dialog shows the resulting
Offset parameters:
As with the Offsets, entering a negative number will create a Joint, while a
positive one will result in an overlap.
36
Punching Manual
2.4.2
Wire
This option also lets you add joints, but here you can create a joint in the middle of an
entity. This is done by splitting entity into two parts with a Joint between them, and
CAMing them individually.
The Split Position setting determines the positioning of the Joint:
At Hit Boundary will place the Wire at the nearest Hit Boundary to the
clicking position.
At Snap Point will position the Wire according to the current Snap setting.
At Specific Distance\Angle
o For Line entities will treat this parameter as a distance, and place the
Wire accordingly.
o For Arc entities will treat this parameter as an angle, and place the
Wire accordingly.
The following Wire example was created with the setting shown above, that is
Width value equals 2, At Snap Point, with
. As you can see, the
entity is being punched with two distinct punches. Using Edit CAM option, you will be
able to see the resulting Offsets parameters:
2.5
Set Tool Sequence
This option is very useful when on the part there were placed a few CAMs with the
same tool, but you dont want all the CAMs to be made in one sequence (for
example, if for each of the CAMs you want to apply different Optimization strategies).
In this case for one group of CAMs with the same tool you can set a certain
Sequence and for the other group you can set another Sequence.
When you choose this option, a following dialog will appear:
37
cncKad
Enter desired tool sequence number and confirm your choice clicking OK button.
When the dialog will close, click on the project the instance of the tool you want to
apply this sequence to, or, with the help of Select Option Toolbar, assign it to
several different tools at a time.
The default sequence number is "0", and it denotes the main tool.
From now on these CAMs will be considered as if they were made with different tools
you can apply to them different strategies, place them in different positions in the
general CAMing sequence, etc.
In the list of used tools, which can be found on the panel on the left side of the
screen, you will see the tools to which sequence was added, behaving as if they
were different tools:
For punch:
For laser:
You can also add sequence to the tool in Add Punch dialog, Add Cut dialog and in
the Used Tools dialog, in the Sequence column.
Let's presume that a certain part is being CAMed with three tools. The following
picture shows an area of Used Tools dialog, containing these tools:
For punch:
For laser:
As a result of optimization considerations, the CAMs have been split up into different
Sequences. See the below pictures:
For punch:
38
Punching Manual
As you can see above, the tools with sequence assigned to it have the same station
as the tools without it, since machine controllers see them as just one tool.
For laser:
2.6
Common Cuts
If you are going to use multiple parts on a large sheet, you will probably wish to save
time and utilize the sheet as much as possible. This can be done with the usage of
this option. It allows you to process outer contours of two adjoining parts at a time,
even when they are processed by special tools.
After choosing this option, the following dialog will appear:
Choose the desired direction of Common Cuts they can be either Vertical,
Horizontal, None or both directions, and confirm your choice clicking OK button.
For Trumf machines choose Use Bottom for horizontal cuts.
For punching (turret) machines it is recommended to choose Use Top for horizontal
cuts, since if the machine has a chute, the processing of a part should finish on the
bottom of the part.
For information on laser common cuts go to: Laser Common Cuts section of
Appendix chapter of current manual.
2.6.1
Vertical
Use Common Cuts to process together parts adjoining in the Y direction. Here you
can see an example of utilizing the Use Left option:
39
cncKad
2.6.2
Horizontal
Use Common Cuts to process together parts adjoining in the X direction. Here you
can see an example of utilizing the Use Bottom option:
2.6.3
Common Cuts Example
Naturally, you can choose None for both directions:
Or you can use both directions:
40
Punching Manual
2.7
Reposition and Transformation
After selecting this option, the following dialog box is displayed:
2.7.1
Transformations
In this section you can not only select the Type of transformation, but also for each of
them you will be able to enter the values of the Offsets from the sheets' edges in X
and Y directions.
In this section of the dialog you can Add the following options of Sheet
Transformations:
After adding a Transformation type, you can also Delete it, however you cannot
delete the Sheets initial state - Transformation None.
In order to set the offsets in X and Y directions, click th appropriate field and enter
desired value.
41
cncKad
For information about using Repositions with Transformations, see the
Sheet Transformation with Reposition section of Appendices chapter
in this manual.
2.7.2
Reposition and Head position
In this section you can add, edit, delete and assign CAMs to specific Repositions:
The window in this section shows which Repositions are defined for the
Transformation selected in the Transformations section.
2.7.2.1
Add
You can add Repositions by clicking the Add button; you will be presented with the
following menu:
The options for manual determining the Head position are intended for those
occasions when prior punches have been placed where the Post Processor might
have positioned the Head.
After you have set a user defined Reposition, initiating the Repositions by
Post-Processor is no longer possible!
This means that when you wish to add more Repositions to your part, you will only be
offered the manual options:
2.7.2.2
Edit
This option enables you to edit pre-defined Repositions.
2.7.2.3
Set CAMs to Current
This option enables you to associate specific CAM(s) to a specific Reposition.

After clicking this button and using the selection options, from the Selection Toolbar,
you can select the CAMs you want to associate with the particular Reposition.
2.8
Push Out (Chute)
This function is designated for machines that have a chute on the table parts that
have been cut out of the sheet can be removed from the table via this chute. This
avoids having to use a Stop Machine command and remove the part manually. The
position of the chute varies from machine to machine.
When you choose this option, the following dialog appears:
42
Punching Manual
After setting desired parameters, confirm your choice clicking OK button. The dialog
will close and you will be able to add this attribute to an existing CAM. All you have to
do is click the punch you want to Push Out through a Chute. It will be marked with
green color.
You can also use this option to place a Stop Machine command.
2.8.1
Chute Type
From this dropdown list you will be able to select the position of the chute in relation
to the punching/cutting head on the machine:
Stop choosing this command equals applying the Add or Remove Stop
Machine option from CAM menu.
Push Out on Center if the machine has a chute in the middle of the table,
choosing this option will allow you to push out the processed part or the
remnant (depending on your preferences) through this chute to the bin.
Push Out to Left if your machine has a chute on the left side of the table,
choosing this option will give machine a command to use it.
Push Out to Right if your machine has a chute on the right side of the
table, choosing this option will give machine a command to use it.
No Movement Push Out selecting this option cause only the part which is
above the chute to fall through it to the bin. Other parts won't be moved by
machine towards the chute.
Fixed Push Out this option is designated for machines that have a fixed
chute, with no possibility of opening or closing the chute door.
Remove Push Out choosing this option you resign from using an already
set Push Out function.
2.8.2
Push Out Modes
The chute has two modes: Open and Close. They are designated especially for
Trumpf machines, which have an option of opening the chute at the beginning of the
process and closing it afterwards.
43
cncKad
2.8.3
Last Hit On Center
Choosing this option you decide to place the last hit on center of processed entity.
2.8.4
Open Chute, then Last Hit
Marking this checkbox tells the machine to open the chute first and then place the
last hit on the processed entity.
2.8.5
Head up
If you want the turret head to be raised during pushing the part out, select this option.
2.8.6
Bin Number
Here you enter the number of the bin/palette to which the pushed out part will fall
into.
2.8.7
Auto Tool Order
Marking this checkbox allows you setting automatic tool order according or opposite
to the hands of the clock (CW or CCW), by selecting the appropriate option.
2.8.8
User Defined Movement
In this section you will be able of defining how the machine should move the part in
order to push it out through a chute to the bin.
2.8.8.1
Move
If you mark this checkbox, you will be able to enter values, in the dX and dY fields, of
the point to which the machine should move.
2.8.8.2
Open Chute, then Move
Checking this option you make machine open the chute first and then move the part.
2.8.8.3
Reduce Speed for Movement
When you mark this checkbox the Reduced Speed option becomes available for
editing. From the Reduced Speed dropdown list you will be able to choose the most
fitting speed for your movement: Low, Medium or High.
2.8.9
Push Out Profiles
This option is useful for machines with a few chutes. You can create and store the
profile with settings for each chute and load it, when needed, without having to
assign all the definitions form the beginning every time you make a Push Out.
After configuring definitions for specific push out type, go to Profile section. In the
dropdown list field type the name for the profile you want to create and click Save As
button. If such a name already exists, you will be presented with following warning:
If you want to overwrite (update) the existing profile, click Yes button; otherwise click
No.
44
Punching Manual
Profiles are stored separately for each machine you have. You cant use one
machines profiles on another one (you have to create a new profile), but you can
give profiles of different machines the same name.
When you assign a Push Out to a CAM, this action will be executed after the CAM is
performed.
A CAM defined as a Push Out will be colored green.
For loading an existing profile configuration, from the dropdown menu choose the
name and click the Load from button.
2.9
Add or Remove Stop Machine
This function adds or removes a Stop Machine from a specific CAM. To do this, after
choosing this option simply click the CAM you want to apply the Stop to. To remove
the Stop from it, click again on the CAM.
Using this option is the same as choosing a Stop type of the Push Out.
A punch with assigned Stop Machine function to it will be colored red.
2.10 Positioning (No CAM)

A No CAM means that the machine will go to the coordinates of the chosen CAM,
but the selected position will not be processed, when the program is run.
To apply this feature click the CAM you want to change. The processing will
disappear and an X will be located in its place (the color of the X will depend on the
nature of the CAM it replaced, e.g. a Push Out CAM colored green will become a
green mark, a Stop Machine CAM colored red will become a red mark, etc.):
Before:
After:
This command is useful for forcing the machine to traverse a selected path even
when there are no CAMs in that path, for example when you want to avoid a clamp.
A No CAM can be converted back into a CAM by clicking the same position again.
2.11 Cut Sheet

This feature enables you to cut your sheet to a predefined size. After selecting this
option, the following dialog will appear:
45
cncKad
After setting the Tools and Wire Joint click OK button to close the dialog. Click one
side of the sheet, and then click another one. As you now move the cursor, you will
see a line under its crosshairs this is the Cutting Line, and it will be drawn
perpendicular to both sides chosen. When you click the mouse, the sheet will be cut
in the defined position:
If you have chosen opposing sides of the sheet, the cutting line will be drawn
up-down or left-right. (see example below).
If you have chosen un-opposing sides, e.g. left and top, two intersecting lines
will be drawn (see example below):
o The first one, left-right or top-bottom (depending where you clicked first),
will cut the sheet from side to side.
o The second one will be placed from the side of your second click to the
first line.
Apart from the direction of the cut, advanced programmers can set a value for the
offset from the sheets edge.
2.11.1
Tools
Marking the Auto Tool Selection checkbox you can let cncKad select appropriate
tools for Cut Sheet operation or you can decide about it yourself by clicking on
horizontal and vertical tool buttons. The tool library will open allowing you to choose
the tools.
2.11.2
Offset
The Cut Sheet Offset can be defined according to your processing needs by
entering the value in the Offset field or by entering the value in the machines MDL
file, in the [Sheet Cutting] section, e.g.:
Cutting Offset = 5.0 // To be used for CutSheet command
The value can be:
46
Punching Manual
Positive the CAM (punch or laser cut) will be offset beyond the edge of the
sheet. In this case a Stop Machine feature will be added after this CAM.
Negative the CAM (punch or laser cut) will be offset into the sheet, leaving
a MicroJoint. In this case a Stop Machine feature will NOT be added.
2.11.3
Wire Joint
This option is available only for punching machines.
If in this section you will check Perform box you will be allowed to place Micro Joints
(Wires, actually) as an integral part of the punch. You can set the width of the Micro
Joints (W) as well as the maximum distance between them (ML), and they will be
integrated into the punch, without splitting the entity being punched.
Choosing one of the After First Hit and Before Last Hit options enables creating
Micro Joints after the first and before the last punch. They address the issue of
rounded corners when punched by round tools.
More information on this option you will find in the Wire Joint section of the Add
Punch dialog of Punch Manual chapter of Punch Manual.
2.11.4
Cut Sheet Examples
See below:
2.11.4.1
Cut Sheet Left Right
In this example the punching is colored red to denote a Stop Machine, as

the Offset is 5mm over the sheets edge.
47
cncKad
2.11.4.2
Cut Sheet Left Down
In this example the horizontal punching is colored red to denote a Stop

Machine, as the Offset is 5mm over the sheets edge.
However, Stop Machine option wasn't assigned to vertical punching
and at this time there is no need doing this.
2.12 Defining Functions

Functions are special machine related commands that can be inserted into NC codes
at specific positions. The codes and the quantity of functions available vary from
machine to machine. For instance, an older mechanical punching machine will have
fewer abilities than a newer hydraulic machine.
These special commands can be associated with specific CAMs, tools or programs:
2.12.1
Punch or Cut Functions
These options allow for adding functions immediately before or after a CAM:
2.12.1.1
Set CAM Functions
This option allows you to set function/s for various CAMs.

After choosing this option, the following dialog will open:
48
Punching Manual
Define the Pre- or Post-CAM functions you desire, and click OK button.
You will be returned to the drafting window, where you can click all the CAMs you
want these functions to apply to.
2.12.1.2
Edit CAM Functions
This option allows you to edit already existing functions for a specific CAM, or set
new ones if none are defined.
After clicking this option, you will be moved to the drafting window, where you can
click the CAM you want to assign the selected functions to. After choosing a CAM,
the following dialog will open:
Define the Pre- or Post-CAM functions you desire, and click OK button.
2.12.2
Defining Tool Functions
This option is accessible also by clicking the

icon from the Common Toolbar and
loads the Used Tools dialog, allowing you for adding functions to a specific tool. In
the dialog, from the tools list, select the tool that you wish to add the functions to, and
click the Tool Functions button; the following dialog will be displayed:
49
cncKad
Clicking the dropdown lists displays the functions that can be added to the program
(they vary for machines). Select the ones you want to add you can add two
functions for each of the following options:
Before Tool Before loading the tool.
After Tool After putting the tool back.
Before every Punch with this Tool
After every Punch with this Tool
In Tool Change When changing one tool for another one.
After defining the functions confirm your choice clicking OK button.
If you don't want to assign any function to any of above mentioned fields,
select from the dropdown list the option NONE.
The selected functions will be shown in the Used Tools dialog, in given tools line:
It is possible to add default functions to a tool so that every time that specific tool is
used, in any program, it will always come with the defined functions.
2.12.3
Defining Program Functions
This command gives the user the option to place special machine commands at the
beginning or at the end of the program.
After choosing this option you will be presented with the following dialog:
50
Punching Manual
From this dialog you can define functions that will be activated before or after running
NC program.
2.13 Set Sheet and Clamps

This dialog can also be accessed by pressing the Set Sheet and Clamps button
.
The parameters you define through this dialog determine how the part you created
will be processed.
Click the tab you wish to view:
For punching machines:
For laser machines:
2.13.1
Sheet Tab
This tab varies for punch and laser machines. The parameters in this tab pertain to
the Sheet you will be placing your part on.
For punch machines it looks like this:
51
cncKad
and for laser machines it looks like this:
52
Punching Manual
2.13.1.1
Sheet Size
In the Sheet Size fields you can view and manually define the X and Y sizes of the
sheet.
2.13.1.2
Set Sheet = Part
Clicking the Set Sheet = Part button will cause the Sheet to become the same size
as the Part. If you use this option, you should pay attention to the clamps' status.
2.13.1.3
Select Sheet
By clicking this button the following dialog will appear from which you will be able to
select standard sized sheet:
53
cncKad
The sheet sizes presented here are being taken from Material Database, which can
be accessed from Settings menu => Workspace Settings => Material tab =>
Standard Sizes button.
In the Quantity column you will see the number of specific sized sheets which are
stored in Material Database.
2.13.1.4
Number of Parts
In the X and Y fields you will see the maximum number of parts (or actually
geometries) fitting each direction. These copies of the part are called multiple parts.
Changing the sheet dimensions will automatically update this data.
In the X x Y fields, which are not available for editing, you will see the amount of the
geometries (which sometimes consist of one and sometimes of more parts) fitting the
currently chosen sheet size. Changing the sheet dimensions will automatically
update this data.
In the Total field, also not available for editing, you will see the entire amount of the
parts (NOT geometries, but all the parts in geometries) fitting the currently chosen
sheet size.
Changing the sheet dimensions as well as manually updating the number of Parts in
Geometry field on Part tab will automatically update data in this field.
You can set manually the number of parts on the sheet in two ways:
Enter the desired number in the X and Y fields.
Change the size of the sheet.
2.13.1.5
Offsets
The parameters entered in these fields define the distance by which the parts will be
moved from the edges of the sheet.
2.13.1.6
Sheet Area and Weight
This section, not available for editing, presents the area of the sheet (in square
meters) and its weight (in kilograms). This data is calculated on the basis of the
sheet size, it's thickness, material type it is made of. The values presented here will
be automatically updated any time you will change the material, thickness or the
size of the sheet.
2.13.1.7
Material Choice
From the dropdown Material List you can choose or change the material for the
sheet you are working on. The materials in this inventory are being taken from the
Sheet Database of Material tab of Workspace Settings.
For more information on this subject go to the appropriate section of Settings Menu
54
Punching Manual
2.13.1.8
Program Functions
This option is available just for punch machines.
Using this option you can add functions for current part that will be included to your
NC program.
For a full explanation of this feature go to the Defining Program Functions section of
this chapter.
2.13.1.9
Sheet Thickness Choice
From the dropdown Sheet Thickness list you can choose or change the thickness
for the sheet you are working on. The thicknesses in this inventory is being taken
from the Sheet Database of Material tab of Workspace Settings.
For more information on this subject go to the appropriate section of Settings Menu
2.13.1.10 Choosing Sheets Quantity

In this field you can enter the number of the sheets you want to process with this
part.
2.13.1.11 Technology Parameters

This option is available just for laser machines.
The definitions of the options seen in Technology Parameters section, like Gas,
Head and Lens type, are being taken from the Cutting Technology Table described
in Settings Menu chapter of Drafting and Nesting Manual.
2.13.1.12 Technology Table

This option is available just for laser machines.
The non-editable parameters presented in Technology Table section are taken from
the Cutting Technology Table described in Settings Menu chapter of Drafting and
Nesting Manual. Sometimes the thickness here may differ a bit from the one you
chose in Thickness dropdown list. This means that your machine's Cutting
Technology Table doesn't contain exactly the same the thickness your sheet has,
and that's why it shows the value closest to it.
2.13.1.13 Sheet Type

Here the user can define a type of the sheet to be used. This parameter is important
for your machine, that she would know when to increase the height of the head, if
necessary.
The types of sheets are:
Normal this type designates regular, plain sheets.
Formed sheets that have been formed beforehand.
Irregular sheets with rough surface.
2.13.1.14 Run the program

This option defines how your sheet will be utilized. Some machine operators tend to
process a half of the sheet, turn it over or rotate it and then continue processing the
other half.
Select the most suitable option for your machine:
Once per Sheet the program will be run once, on the entire sheet.
Twice with Rotation the sheet will be split and rotated, therefore the
program will be run twice.
55
cncKad
Twice with Flip the sheet will be split and flipped, therefore the program
will be run twice.
Your choice may be changed at any time during the NC program creation process.
2.13.1.15 Start Parts Placement

This section allows the user to determine from which side of the sheet the parts'
placement will be initiated. You can choose one of two options, as their names
suggest: From Clamps or Opposite Clamps.
2.13.2
Auto Tab
All the options presented in this tab relate to the export of files from cncKad to the
Automatic Nesting module Auto Nest. After setting here proper parameters
cncKad will analyze contours and allow automatic processing to occur.
All the parameters set in this dialog are being defined for the current part you are
working on. After exporting the part to Auto Nest you will be able to view and edit
them in Part Information and in Global Info dialogs:
56
Punching Manual
57
cncKad
2.13.2.1
Buffer
Buffer is the area around a part that separates it from the other parts placed in the
nest. There are a few options for setting parameters for buffer:
2.13.2.1.1
Use Global
If this option is checked in cncKad, before exporting parts into Auto Nest, the default
buffering parameter will be taken; else the parameters you defined on the Auto tab
will be used.
When importing a part, while being in Auto Nest, you will have the option to set a
default buffering parameters in the Import Setup dialog.
2.13.2.1.2
Hole buffer size
This parameter defines the size of the area around a hole inside the part.
2.13.2.1.3
Use Rectangular Border
If you check this option, the buffers will be calculated according to the parts
bounding rectangle. Use the Left, Right, Top and Bottom parameters' fields to set
the desired buffering values for each side of this rectangle.
2.13.2.1.4
Use Part Border
When you check this option and define the Buffer Size value, the buffering will follow
the part's contours.
2.13.2.2
Mirror Allowed
Here the user can define whether the part can be mirrored on the sheet during
automatic nesting or not. When the Global option will be chosen, the mirroring
settings will be set to default, determined during the importing to Auto Nest.
58
Punching Manual
2.13.2.3
Direction
This option allows user to define the number of directions the part can be rotated in,
while being nested. When the Global option will be chosen, the mirroring direction
will be determined during the importing to Auto Nest.
2.13.2.4
Common Cuts for Grouped Arrays
In this section the user will be able to determine whether, and how, the part will be
nested utilizing common cuts option for arrayed group.
This is done by choosing desired direction of the CAMs and selecting the side of the
part they will be connected to:
Vertical use Common Cuts to nest parts adjoining in the Y direction; the
available side options are: Right, Left or None.
Horizontal use Common Cuts to nest parts adjoining in the X direction; the
available side options are: Top, Bottom or None.
It is also important to define the Distance between Parts for common cuts. You can
choose a Default Value, which is being taken from Auto Nest module or by entering
some other, Manual Value.
2.13.3
Global Cut tab

This tab is available for laser machines only.
The options in this tab allow you to define Z option and Corner parameters for the
current part:
59
cncKad
These definitions will be active for all the entities and corners that are set to
GLOBAL.
The full explanation on the options presented here, you will find in proper sections of
Laser Manual chapter of Laser Manual. For explanation on specification of the
colors we use to mark cutting speeds with go to View menu => Colored Tool Path
by Speed section of Drafting and Nesting Manual.
2.13.4
Cutting Parameters Tab

In this tab you will be able to set the cutting parameters for the current sheet:
60
Punching Manual
2.13.4.1
Piercing
The parameters presented in the Time and Set fields, not available for editing here,
give an information on the current sheets piercing properties. This information is
taken from the Piercing tab of Cutting Technology Table of the current laser
machine.
See the appropriate section of Settings Menu chapter of Drafting and Nesting
Manual.
2.13.4.2
Sheet Thickness and Material
The data presented here for Sheet Thickness and Material type, not available for
editing from here, is being taken from the Sheet tab.
2.13.4.3
Vaporization
This command is useful when the sheet is covered with nylon film: the laser beam
will pass a first time, with low power, over the parts in order to burn the nylon, before
it passes a second time for actual cutting.
From the dropdown list the user can choose how he wants his Vaporization to be
set: for Whole Cut, for Pierce Only, or None. If you choose None, the Use
Vaporize for Engrave function will be deactivated.
2.13.4.4
Dynamic Piercing
Checking this box activates the Dynamic Piercing option.
2.13.4.5
Use PrePiercing
If you check this option, the "Pierce Only" command will be generated a for the
entire sheet once the piercing will have been executed, the sheet will be cut without
piercing.
61
cncKad
2.13.4.6
Use Standard Shapes
Activate this option to define Laser Standard Shapes in the NC code as one-line
codes (if the machine supports this option; otherwise it will be unavailable for editing).
2.13.4.7
Use Vaporize For Engrave
The user can choose here whether he wants to use vaporization for engraving.
This option becomes available only when the Vaporization is set for Whole Cut or
for Pierce Only.
2.13.4.8
Cutting Speed
The parameters presented in this section, not available for editing here, give
information on the current sheets cutting speed properties. This information is being
taken from the Cutting tab of Cutting Technology Table of the current laser
machine.
See the appropriate section of Settings Menu chapter of Drafting and Nesting
Manual.
2.13.4.9
Point Marking Style
In this section the user can select the style and define the size of Point Marking
Styles, which will indicate the location of the hole(s) you are not interested in cutting.
These holes will be engraved instead.
Usually this function is being used for marking the undersized holes. By default the
style of point marking is defined as a spot. For this option there is no possibility of
setting the point size, but if you will choose one of the other marking signs, you will
be able to define its dimensions.
2.13.5
Part Tab
The attributes of this tab are concerning various aspects of the current part:
62
Punching Manual
2.13.5.1
Part section
This section gives you various information about the part in your draft. Most of these
options, but some, are unavailable for editing.
2.13.5.1.1
Part Size View
In the X and Y fields you can see the dimensions of the current geometry. Any
number of parts copied and placed on the draft will be always treated by cncKad as
one geometry, and not as multiple parts. Therefore in these fields you will see the
size of the whole geometry area, and not an area of a single part (unless your
geometry contains just one part).
2.13.5.1.2
Number of Parts
This field reveals you how many parts does your geometry consist of. If there is more
than one copy of the part placed in your geometry, here you will see how many.
2.13.5.1.3
Number of Holes
63
cncKad
In this field you will be able to see how many holes are in your geometry. If your
geometry consists of a few copies of a part, the number of holes will be a total
number of all of them.
2.13.5.1.4
Entities Section
In this section you will see the specification of all the Lines, Arcs, Circles and
Points placed on your geometry. If your geometry consists of a few copies of a part,
the number of entities will be a total number of all of them.
2.13.5.1.5
Distance Between Parts
In the dX and dY fields of this sections you will be able to enter the distance you wish
to be between the geometries placed on your draft, if your geometry consists of a few
copies of the part. If a geometry actually equals a part, the value entered here will be
in fact a distance between the parts.
2.13.5.1.6
Parts in Geometry
cncKad has an ability to maximize sheet usage by placing on a draft a number of

parts that behave as a single part.
cncKad sees the two (or more) contours as a single part, and this way when you
enlarge the sheet, make multiple-parts and use common cuts the upshot of this
procedure is, in fact, a very efficient "Nest".
When you use such a procedure, you must also manually update the Parts in
Geometry field, otherwise the program will not be able to give you a correct total
number of parts for your sheet.
2.13.5.1.7
Part Area
This field, not available for editing, presents the area of geometry (in square meters).
This data is calculated on the basis of the geometry size, sheet thickness and the
material type it is made of. The values presented here will be automatically updated
any time you will change the material, thickness or the number of parts the
geometry consists of.
If the part is an open contour, the program will give an approximation of the
values, indicating this with the sign ~.
2.13.5.1.8
Part Weight
This field, not available for editing, presents the weight of geometry (in kilograms).
This data is calculated on the basis of the geometry size, sheet thickness and the
material type it is made of. The values presented here will be automatically updated
any time you will change the material, thickness or the number of parts the
geometry consists of.
If the part is an open contour, the program will give an approximation of the
values, indicating this with the sign ~.
2.13.5.1.9
64
Bend Line K Factor
Punching Manual
In this field you will be presented with the default Bend Line K Factor. Here you
have also a chance of changing it for current part you are working on.
More on K Factor you will find in appropriate section of Drawing Entities chapter, in
Drafting and Nesting Manual.
2.13.5.2
Sheet section
cncKad gives you the ability to place parts in Sheet Mode, as distinct from the parts
that are placed in Part Mode.
2.13.5.2.1
Sheet Area
This field, not available for editing, presents the area of the sheet (in square meters).
This data is calculated on the basis of the sheet size, it's thickness, material type it is
made of. The values presented here will be automatically updated any time you will
change the material, thickness or the size of the sheet.
2.13.5.2.2
Sheet Weight
This field, not available for editing, presents the weight of the sheet (in kilograms).
This data is calculated on the basis of the sheet size, it's thickness, material type it is
made of. The values presented here will be automatically updated any time you will
change the material, thickness or the size of the sheet.
2.13.5.2.3
Entities on Sheet
In this section you will see the specification of all the Lines, Arcs, Circles and
Points of which the shapes placed on your sheet consist of.
2.13.5.2.4
Parts in Geometry on Sheet
You should fill in this field, in order to allow cncKad for a correct counting of overall
parts on the sheet.
2.13.5.2.5
Create unique IDs for entities
This option is designated for the parametric design. It gives the user control over
every entity in the draft file (.DFT) by activating the allocation of unique IDs for each
entity, generating a unique ID for all the existing entities in the drafting and for every
new entity that will be created from now on in this part.
These IDs can be used for methods dealing with Entities, Drawing, Punching, Cutting
and adding Dimensions.
2.13.6
Clamps Tab
If your machine has movable clamps, you can define their settings here:
65
cncKad
If your machine doesn't have movable clamps, you won't be able to edit their
positions from here.
2.13.6.1
Clamp Coordinates
Normally, when you set a new Sheet Size in X, the Clamps are automatically being
set at recommended values, according to the current machine's options.
You can change these values manually, either by dragging the clamps with the
mouse or by entering values in the appropriate fields of the Clamps tab dialog.
cncKad will NOT allow you to place clamps in positions which cannot be set
physically on the machine, but you will be able to choose any other legitimate
position you wish.
These positions will be changed automatically in the following situations:
Working in the Dead Zone
Changing the Sheet Size in X
Changing the machine
2.13.6.1.1
Working in the Dead-Zone
In this case, cncKad will try to generate an NC program based on the current
positions of the Clamps, and if successful, will NOT change their positions. However,
if unsuccessful, cncKad will set new positions for the clamps. This means that the
positions will be changed (if necessary) during the Post Processing stage the
change will not appear during the drafting and processing stages.
2.13.6.1.2
Changing the Sheet Size in X
After you change the sheet size in X, cncKad will recalculate the recommended
positions for the new size, and will automatically set the clamps accordingly.
2.13.6.1.3
Changing the machine
After you change the machine, the clamps positions will be corrected only if needed
(e.g. when a clamps positions are off the new machine's table)
If you want to set the clamps to the recommended positions for the new machine,
you can change the sheet size in X, and their positions will be recalculated.
66
Punching Manual
2.13.6.2
Max Used Clamps
You can choose the number of clamps you want to use, if your machine allows it. If
your machine doesn't support clamps, this option will not be accessible for editing.
If you have a machine with four clamps (such as Trumf 6000L ), you can choose,
from dropdown menu, one of the below listed options:
If you choose ALL, the maximum number of clamps will be used in this case 4. If
you choose NONE, no clamps will be holding your sheet. If you want your sheet to be
holed by one to three clamps, select the appropriate number from the dropdown list.
2.13.6.3
Restore defaults
Clicking this button will return to the primary settings of the clamps for your current
machine.
2.13.7
User Data Tab
On this tab you can include the information about the customer who ordered the part
to be created, the programmer who designed it, and about the project itself its
number, description, as well as other additional information. This data can be saved
together with the part file.
Entering it into these fields is not compulsory and can be added at any stage of part
drafting as well as during NC code creation process.
You can copy the information entered here and later on paste it to different part, as
well as edit the default titles of these fields.
67
cncKad
2.13.7.1
Edit Titles
The default titles, which will appear later on in the Report File, of User Data dialog,
can be edited and customized according to your needs. To do so, click on the Edit
Titles button. The following dialog will appear:
The numbered titles here refer to the titles of the fields in the User Data tab and they
are set to their default (for reminder see the right side of this dialog). You can change
them just by clicking on the field and inserting the new title (as shown on the picture
above). It will be then updated in the User Data, and eventually also in the
corresponding fields of Report File.
If you wish to restore a titles default, just leave its field empty. If you want all the titles
to be restored, click the Restore Default Titles button.
2.13.8
Sheet Processing Technology Tab
This tab deals with overall strategies to be used while creating your part.
More explanation on the reasons for using the Sheet Processing Technology and
other important issues concerning this topic you will find in the Sheet Processing
Technology Tab dialog of Machine Settings dialog in Settings Menu chapter.
The difference between that tab and this one is that the settings defined here
influence only the current part, and the ones defined there are general defaults which
will be used only after you reload the current part, create a new one or the next time
you open cncKad.
68
Punching Manual
2.13.8.1
Tools' Processing Strategy
From this section of the dialog you can set the strategy cncKad will use when
creating your NC code. Here you can decide how to distribute the CAMs of various
tools.
2.13.8.1.1
All Sheet Processing
First the machine will perform all the CAMs on the sheet with a one tool, and only
then it will move on to the next tool.
2.13.8.1.2
Part Processing
Perform all CAMs on one part with ALL the tools (actually, all the Blue tools), and
then go to the next part.
This option is useful when working with thick material or with old machines, where
there is a high risk of the machine getting "stuck" in such case, at least some of the
parts are completed. Mark the "safe" tools as Blue they will work all over the sheet,
the Red tools will work Per Part.
2.13.8.1.3
Stripe Processing
Perform all CAMs with all the tools (actually, all the Blue tools) on current stripe, and
then go to next stripe. Use this option for parts with many holes, where the sheet may
easily get bent. After completing processing a stripe, you can remove it.
This option will not work on nestings.
69
cncKad
2.13.8.2
Tools Section
This section shows the tools used in the processing of your part. If you have selected
the strategy for All Sheet, this field will be grayed out and thus unavailable for
editing. If your strategy is either Part or Stripe, you will be able to mark here "safe"
tool as Blue ones and the tools, which are allowed to work only per selected
strategy, as Red ones.
2.13.8.3
Optimization Strategy
The options presented in this section govern the way your CAMs will be optimized.
For processing of Parts, Vertical and Horizontal Cuts you can define here the
Starting Corner and the Optimization Path:
Starting Corner sets the point where the optimization path begins.
Optimization Path sets the optimization type; Snake X, One Way Y, User
Defined, etc.
More explanation on this subject you will find in Starting Corner and Optimization
Path in the Settings Menu chapter of Drafting and Nesting Manual.
2.13.8.4
Stripe section
These options provide settings for the Stripe Processing strategy:

No. of lines per Stripe here you need to enter the quantity of parts per
rows, which will be processed in one stripe, at a time.
Remove Stripes with this option you select whether or not to remove the
stripe when the machine finishes processing it. If this option is marked, a
trimming cut is created.
Direction of Stripes Removal when you choose to remove the stripe, you
can select the direction of the punch (or cut) that will disconnect the stripe
from the rest of the sheet.
Removing Tool when you choose to remove the stripe, you must choose
the tool that will be used for the cut removing the stripes.
2.13.9
Trim Sheet Tab
After you have finished processing all the parts on your sheet, you will be left with the
outer remainder of the sheet. The options of this tab let you dispose of this
remainder.
After selecting the trimming tool, choose the way you want the sheet to be trimmed.
For more information on trimming the sheet go to Creating a Trimmed Sheet
section of Appendices chapter of this manual.
70
Punching Manual
2.13.10 Reposition Tab

This tab gives you an opportunity of defining the reposition parameters that will be
used during the Post Processing stage, during which the NC code is created for the
part. Repositions are typically performed by moving the clamps and placing pins on
the sheet to hold it in place when the clamps change their position.
Here you can see various repositioning options:
71
cncKad
2.13.10.1 Manual Reposition

This option is valid only when you have already defined repositions manually, with
the aid of the Reposition and Transformation function described in current chapter.
This will give priority to repositions you have already set and will make no changes to
them.
2.13.10.2 Auto Reposition

When selected, cncKad will set the repositions as you specify in the dialog,
overriding any previous reposition definitions you may have set.
2.13.10.2.1 Quantity of Repositions

In this section the you will be able to define the number of repositions you want to be
made for your sheet. Choose the option that fits you best.
2.13.10.2.1.1 Minimum repositions
Choosing this option causes the machine to create as few repositions as possible in
order to perform the needed CAMs. If necessary, it will split the processing of a part.
2.13.10.2.1.2 Minimum part breaks
With the aid of this options the machine tries to set the minimal number of repositions
needed, so as not to split the processing of any part. This may result in having more
than the minimal number of repositions possible, but cncKad will make sure that
each part is processed in a single reposition (unless the part itself is bigger than the
reach of a single reposition).
For example, when your parts are placed on a sheet that extends beyond the table,
and therefore requires repositioning, cncKad will try to process the entire part, make
the reposition, and then process the next part. In this way there will be less of a
chance for inaccuracies resulting from repositioning.
72
Punching Manual
Another reason for using this function is when your machine has a slow repositioning
mechanism and you want to make as few repositions as possible.
2.13.10.2.1.3 User defined
This option lets the user define the repositions by himself. If he selects illegal
positions, or the Post Processor cannot reach the whole sheet due to the defined
repositions, an error message will be issued and abort the NC creation. In any case,
the repositions set by the user will not get changed.
When defining repositions, the user chooses the position relative to the sheets left
edge, where the machines Working Range will begin.
For example, for a machine with a Working Range of 1000, processing a sheet
2000x1000 the following repositions have been defined 600 and 1000. The
processing will proceed as follows: The machine will first process the CAMs in the 0600 range, then the ones in the 600-1000 range, and lastly the ones in the 10002000 range
There are a few things to be noted when entering reposition values:
No negative values are allowed.
Each reposition value must be bigger than the previous one (it doesn't apply
to the range).
Make sure that in the last reposition, the machine reaches the end of the
sheet.
The "zero" position is always the sheet origin, therefore it is unavailable for
editing.
2.13.10.2.2 Max/Min Processing

The options presented in this section allow you to choose the minimal or maximal
range of the sheet to be processed during each reposition.
Max at 1st grip at each grip (reposition) the machine will try to process as
much of the sheet as possible.
Max at last grip whenever two grips (repositions) overlap, the machine will
let the overlapped section to be processed in the next grip.
When a Forming Tool is used, it is often placed in a turret as the last tool, so that the
tools following it (especially punching tools like a long RE tool) will not "flatten" the
form. However, if the sheet you want to process is longer then the working range,
and Reposition is required, the cutting tool used after the Reposition (in the 2nd
"grip") can flatten the forms that were created in the 1st "grip". To solve this issue, we
can define the Min/Max Reposition per tool.
For example, suppose that we are processing a 2000mm sheet on a 1250mm
machine. We will set in Set Sheet and Clamps => Reposition tab to have:
o [x] Max at 1"st Grip
However, in Used Tools => Tool Data => Reposition Types we will set for the
Forming Tool:
o [x] Max at last Grip
Now, all the tools will process up to 1250mm, but the Forming Tool will process only
up to 750mm.
After the Reposition, all the tools will process between 1250 - 2000, but that will not
be a problem for the forms they were made only up to 750. Finally the Forming
Tool will complete the forms from 750 - 2000.
2.13.10.2.3 Reposition Safety

These options deal with the repositioning of the Sheet before and after it has been
processed:
73
cncKad
None will not add any reposition before or after the sheet processing.
Reposition Back after the sheet have been processed it will be brought
back to its original position by repositioning the clamps.
Start process from right side the processing of the sheet will start at the
opposite side of the sheet than the one usually in use (left corner at 0,0
location). Therefore, the sheet will be repositioned before the processing will
start and in the end it will have the same position as when it was loaded. This
option is useful for sheets that contain few micro-joints, for instance, in order
to avoid loss or damaging of parts.
2.13.10.3 Tool Reverse Order for Reposition/Transformation

This function is being used after the reposition/transformation in order to save the
tool change. Choosing this option we reverse the order of tools set in Used Tools
dialog of Tools Menu chapter, for processing the parts on transformed or
repositioned sheet.
2.13.11 Load/Unload Tab

This tab presents options intended only for machines with an ability of automatic
sheet loading or unloading. Their attributes are as follows:
2.13.11.1 Sheet Loading

This section allows the user to define parameters for loading a sheet.
2.13.11.1.1 Loading Mode

The mode of loading the sheet can be manual or automatic, depending on machine
you have.
2.13.11.1.2 Pin
74
Punching Manual
Pin refers to those machines that have a second pin, for pinning smaller sheets.
2.13.11.1.3 Load On Opposite Side of Pin

This option is available for machines who have two pins. Choosing it your sheet will
be loaded from the opposite side of the pins.
2.13.11.1.4 Sheet Measuring

Some machines know how to make measuring of the sheet loaded. If they dont, the
default option "No" will be set.
2.13.11.1.5 Offset
Here the user can define an offset for the loaded sheet. If you will select Auto option
the offset will be defined automatically by cncKad. If you will choose the User
Defined option, you will be able to enter offset value in dX field.
dX is the distance between the 0.0 point (the endpoint of the table) and the
endpoint of the sheet.
2.13.11.2 Sheet Unloading

In this section you can define the parameters for the sheet unloader.
2.13.11.2.1 Unloading Mode

The mode of unloading the sheet can be manual or automatic, depending on
machine you have.
2.13.11.2.2 Size of Processed Sheet

After the sheet has been processed, it is often smaller than it used to be to begin
with. The automatic unloader has to know this new size, therefore you should enter
its new dimensions in X and Y fields.
2.13.11.2.3 Correction for Processed Sheet

If the sheets size has changed during processing, it may appear that the sheets
edge is no longer flush against the tables edge. In such a case the unloader will
have to compensate for this difference.
2.13.12 Laser Optimization tab

This tab is similar to the Laser Optimization tab of the Auto Cut dialog of Laser
Manual chapter, with one important distinction the parameters set here are the
default settings for a part, offered when the Auto Cut dialog is opened for a new cut.
75
cncKad
For more information about the parameters in this tab, please go to the appropriate
section of Laser Manual chapter of Laser Manual.
2.14 Check Process

This option examines the part for unprocessed contours. If any such contours are
found, the following message will be shown:
If you select Yes, the unprocessed contour(s) will be highlighted in blue. If there are
no unprocessed contours found, you will be presented with the following message,
instead:
The Check Process feature is run automatically after Auto Punch and Auto Cut,
allowing you to make sure all the desired contours have been processed. If you want
76
Punching Manual
to set this option to be run automatically as a default, select the Check For Not
Processed Contours option of the Post-Processor Options tab in the Workspace
Settings dialog.
2.15 Set Program Origin

Program Origin refers to position, which is considered to be a "zero position" (0,0),
or a reference point, from which you start running the program.
For many machines, this position is fixed, and defined as for example: bottom-left
corner of the sheet. In some cases, usually in cutting machines such as
Laser/Plasma/OxyCut, the operator can bring the machine head (cutting head) to any
position on the sheet, and start the program from there, thus establishing that
position to be (0,0) or Program Origin.
Normally, the operator will ALWAYS bring the head to the same position, which is
one of the sheet corners. In this case, the Set Program Origin dialog will be grayed
and cannot be used.
If the machine is able support this mode of operation AND you wish to control the
settings of the Program Origin (for each Part/Sheet), then this dialog can be
enabled in the MDL file (see Support for Program Origin section in the Appendices
chapter of current manual). This means that, for example, you want to start some
programs at bottom-left, others at top-left, and yet another one, at some specific point
maybe at the center of a teeth-wheel for which you have prepared some fixture on
the machine.
When this dialog is enabled in MDL file, you should enable it also within the dialog
itself. Only then the other features of this table will be available for editing, and you
will be able to set the Program Origin position by choosing one the four sheet
corners, defining it by yourself, entering its values in X and Y fields or by pressing the
Click on Part button to snap to any position on the Part.
77
cncKad
The Program Origin is displayed as a bold, red coordinates origin, with arrows
pointing to positive direction of X and Y, as shown on below presented picture:
2.16 Unload Part

This feature is intended for machines that have a part removing device. It can be
from CAM
accessed from the CAM Menu or by choosing the Edit CAM icon
Toolbar. When you click the latter one you should click this part's entity you want to
process as the last one before unloading the part. After you do so the following dialog
will appear and on its right side, in Unload section, you will be able to choose the
Unload Part option:
78
Punching Manual
Once you have selected it, the dialog will be closed and you will be moved to the
drafting dialog, where the following Unload Part dialog will appear:
In this dialog, you will be able to determine where to move the unloaded part,
defining the position of the bin, by entering its coordinates on the X axis (and Y axis,
if applicable).
Checking the Auto Tool Order box you allow your machine for automatic arranging
the part processing order.
Clicking Select cups button you will be moved back to drafting dialog and there
you will see an interface that facilitates the cups selection. The rectangles represent
the unloader's arms and the circles the vacuum cups. To move the arms, drag and
drop the arrows alongside.
Click on the cups you wish to use. They will be marked with red color to indicate they
are active.
On some machines the cups that must be activated together are joined by a
line.
79
cncKad
If you want to select all of the cups, press the Alt key while clicking any cup. If you
want to select just cups on one arm, press the Ctrl key while clicking any cup of this
arm. If you wish that the machine to mark all the cups that are on parts, click on
either one of the P boxes next to the arrows. And if you wish to mark each cup
separately, click it with the right mouse cursor.
To confirm the position, click on either one of the tick (V) boxes next to the arrows.
The Unload Part dialog will reopen, and there you should press OK button to confirm
your choice.
If you wish to discard the position, click on one of the cross (X) boxes.
After adding Part Unload function to your part, it will be presented on your sheet this
way:
80
Punching Manual
The green marked entity is the one, after processing which, the part will be unloaded
from the sheet. The red arrows show the direction of processing of the part.
To define the type of cups available, go to Settings Menu => Machine Settings =>
Machine tab => Machine Settings dialog and make changes to the appropriate
machine file in Metalix Editor.
2.17 Cutting Table

This option is a shortcut to the Cutting Technology Table accessed through the
Settings Menu => Machine Settings => Cutting Parameters => Cutting Table button.
For more information on this feature, go to appropriate section of Drafting and
Nesting Manual.
2.18 Adjust Travel Path

This option gives you an opportunity to correct machine's travel path. After selecting
this option you will be able to select new machine path, by clicking the places on the
part you want the machine to process in the new order.
2.19 Restore Default Clamps

Choosing this option will restore the clamps to their default positions.
81
cncKad
3 Tools Menu
This menu allows you to edit various tool-related setups:
3.1
Edit Tools Library
With this option you can access and edit the Tools' Library:
Accessing this dialog from few other places of cncKad you will be presented also
with Setup File tab.
3.1.1
Tool Library tab
On this tab you will find large choice of various tools and options of manipulating
them.
3.1.1.1
Tool Field
When from the Tool Library you select a tool for processing your part its definition
will appear in this field. You can also enter here the tool's definition manually. If the
82
Punching Manual
tool you typed in doesn't exist in your tool library you will be asked if you want to add
it to library. In order for the tool to be used for processing it is not necessary to add
it to the library.
3.1.1.2
Add Tool to Library
The Tool Data dialog can be opened either when adding a new tool, or by clicking
the Tool Data button at the bottom of the Tools Library dialog.
If you wish to add a tool (for CTC tools, see the appropriate section of this manual),
just enter the tool's name in the Tool Field and either press Enter key or click the
Add tool to library button.
You will be presented with the following dialog:
3.1.1.2.1
Common tab
In this tab, user will be able to add detailed features to the new tool, such as: choose
Allowed angles, enter Tool Number (ToolN) as well as Tool Quantity and write a
Comment. They all will be later seen in Tool Table of the Tool Library tab.
From here you can also see the Tonnage of the tool, but you can't enter here nor
change already existing parameters. The value displayed here is being calculated
according to the material tonnage, taken from Material List (Settings => Workspace
Settings => Material tab => Edit Material button), and tool's circumference.
Note that the new tool is being shown on the display, on the left of the screen:
83
cncKad
3.1.1.2.2
Allowed station sizes
In this tab, you can define whether the station size for a tool is selected
automatically according to the tool size, or manually. In the latter case, select the
User defined option and check the box next to desired standard station size:
Clicking on the Set Fitting Station Size button will make cncKad choose the most
fitting station for the tool you are adding to your library.
3.1.1.2.3
Close to clamp
When assigned to a tool, the Close to clamp option allows performing punches
closer to clamps while avoiding clamp/die collision. This option is available for
machines of which dies are not entirely round, but have one or two straight side(s). It
is per tool, and it can be defined for the following tools only: RO, RE, SQ, OB and
MJ.
When creating/adding a new tool to the Tool Library, define a tool as CTC by
entering the tool type followed by the abbreviation "CTC or CTC2 (if you wish to
84
Punching Manual
use a die with two straight sides). Else, you can define the CTC tool through the
Close to clamp tab. RE 45 50 CTC2 will look like the following:
And the punch:
3.1.1.2.4
Type Properties
For some of the Special Tools you can set an additional information in Tool Data,
which is Type Properties. They vary according to the type of the tool:
For Tapping Tools you will be able to set the Speed and Rotation.
85
cncKad
For Forming Tools you will be able to define the values of Bottom Dead
Center and Top Dead Center.
For Wilson Wheel Tools you will be able to set the Depth of the CAM and the
Cutting Speed.
3.1.1.3
Create Tool
After clicking the Create Tool button you will be presented with a dialog where you
can define the exact tool you need.
On the example presented below, you can see how easy it is to create a Triangle
tool:
All you need to do is enter the desired values to proper fields of base (B) and height
(H). When you do this, the angle (A) and the triangle's center (C) will be calculated
automatically by cncKad.
The center value here is the center of the triangles bounding circle.
If you are using Milling machine, you will be able to see also Drill and Mill tabs.
86
Punching Manual
3.1.1.4
Tool Table
In this chart you will find eleven tabs containing various tool types. Go to Tools
Definitions section of this chapter, to see what kind of tools you can find on each of
these tabs.
In order to choose the tool you desire to use for your part's processing, click on it in
tool column, or type its name in the tool field, at the top of the window, and then
confirm your choice clicking OK button.
3.1.1.4.1
Die Selection
The user has a possibility to define Dies for tools. In order to do so, click on the row
with the tool you are interested in, in the Die column. The following dialog will open:
Here you will be able to define the dies clearance and quantity. You also will be able
to edit the already existing ones. Click the
button, to add your definitions to the
button to delete the existing ones. Then click OK button to return to

list, or the
the Tool Library. There you will be able to view the dies list in the appropriate
section:
87
cncKad
As you can see, each tool has its own die list.
cncKad checks what material you are working with, and what is its thickness. Then
according to these parameters, and after verifying in Material List (see Settings =>
Workspace settings => Material tab => Edit material), what are the Minimal, Best
and Maximal Clearances for that material cncKad will decide which of the dies will
be used for current tool.
The results of which die had been chosen for which tool, you see in Die column of
Used Tools dialog:
88
Punching Manual
Dies clearance will not be below or above the minimum and maximum percent
clearances of that sheets thickness, and it will be as close as possible to the Best
clearance defined. If the program will not find the proper die for some tool, in a Die
column a word None, highlighted in blue, will be displayed.
3.1.1.4.2
Allowed Angles
In this column you will be able to see the angles in which tool will be allowed to work.
Clicking on this column next to chosen tool, you will be able to change, choosing one
of the dropdown list options, the angles for this tool.
3.1.1.4.3
Tools Quantity
In this column you will be able to see the quantity of instances of specific tool, which
exist in your library. Clicking on this column next to specific tool, allows you to
change this number.
3.1.1.4.4
Comment column
The comments you entered on Common tab of Tool Data dialog will be visible here.
They can be edited by clicking on this column next to desired tool row.
3.1.1.4.5
ToolN column
If in the Common tab of Tool Data dialog you assigned a specific number to any of
your tools, it (Tool Number) will be visible in this column. You can edit and change it
from here, simply clicking on the chart.
3.1.1.4.6
Tool ID column
This option is designated for Trumpf machines.

cncKad creates automatically the Tools ID for the tools which don't have ones. From
here you can enter the Tool ID's manually, edit and change them, by simply clicking
this column next to desired tool row.
If on the Common tab of Tool Data dialog you entered a Tool ID, it will be seen in
this column.
3.1.1.5
Printing the Library
When you click the Print button the printers settings will appear. Set printing
definitions according to your wish, and the whole Library will be sent to your printer.
3.1.1.6
Renaming a Tool
This button is available only for the special tools tab.
89
cncKad
Clicking the Rename button you will be presented with the following dialog:
Enter the name you want the selected tool to be called by and click OK button. The
following warning will appear:
That means if you have used this special tool on your part, before renaming it, it will
still contain the old name as long as you will be using it on the current part. When you
will use it on a new part it will be called by its new name.
3.1.1.7
Tool Data
Clicking this button will bring you to the same dialog, which appears while you are
adding a new tool to the library. Here you will be able to add or/and edit tool data.
For more details on this dialog, go to: Add tool to library section of current chapter.
3.1.1.8
Copying Tools from one Library to another
Tools can be copied from one tool library to another. In order to do that, select the
Tool(s) you wish to copy to another Library, by the help of regular Windows selection
conventions (hold down Shift key while selecting different tools located one next to
the other, hold down Ctrl key while selecting tools which are far from one another),
and then click the Copy Tools button.
A dialog will appear, offering you to copy selected Tools into one of the existing
Private Libraries. Select the Target Library and confirm your choice, clicking OK
button. The tools will be copied to the designed Target Library.
3.1.1.9
Deleting a Tool
Select the tool you wish to delete, and click the Delete Tool button. The following
warning will appear:
After confirming the action, the tool will be removed from the library.
3.1.1.10
Tool Report
This feature enables you to find all the DFT files on which a specific tool has been
used for processing. In our example we will look for RO 10 tool.
After pressing the Tool Report button the following dialog opens:
90
Punching Manual
Choose the directory in which you want to search and confirm your choice clicking
OK button.
The following Tool Report will display all the instances of the tool found in the
directory we selected:
If no DFT files with such tools were found, no Tool Report will be displayed.
3.1.2
Setup file tab
This tab is visible from CAM Menu => Punch CAM => Add Punch, when you click
the tool button, intending to choose a tool to process your part with. It is also
accessible from Tool Selection Button of the State Bar (see the Introduction
chapter of Drafting and Nesting Manual).
The tools displayed here are being taken from the Turret Setups database.
91
cncKad
In the Station Number field you will be shown the number of the station of the tool
you chose from the table. The Setup File dropdown list allows you for selecting
desired setup file from available ones for currently used machine.
More information on other issues presented in this tab you will find in Edit Existing
Setup section of this chapter.
3.2
Used Tools...
This option opens a dialog, which shows all the tools currently used for processing
your part:
92
Punching Manual
3.2.1
Setting Stations for Tools
There are two ways to set a specific station for a tool:

If you know the station number you desire, click the Stations field of a
specific tool, type-in the number and move on to the next tool.
If you wish to choose from the stations list, click the tools Stations field. You
will be presented with a dropdown list of the stations and the tools assigned to
them:
Choose the station you prefer and click elsewhere in the dialog.
3.2.2
Change Tool
With this option the user will be able to replace the current tool with another one.
When you click this button, you will be redirected to Edit Tools Library dialog and
there you will be able to choose a new tool.
3.2.3
Tool Data option
Here you can also add or/and edit Tool Data. But this dialog varies from the one in
Edit Tools Library window.
93
cncKad
3.2.3.1
Common
This tab differs from the Common tab described in Add Tool to Library section of
this manual. In this tab user can only edit Tool Number and Tool ID and can add his
Comment.
3.2.3.2
Optimization Strategy
In this tab you have the option to determine the optimization strategy for each tool
individually. You can get to this dialog also by clicking chosen tool's field of Optimize
Path column.
You can choose one of two options:

Global Optimization, in which case the parameters will be those defined for
the part.
ToolSpecific optimization, where you have two parameters with which you
will be able to determine your strategy:
o Starting Corner in this dropdown list there are five options of setting the
initial processing corner: Auto, Bottom-Left, Bottom-Right, Top-Left
and Top-Right. Selecting one of them will determine the place of cut
entrance onto the contour.
o Optimization Path in this dropdown list you will find six variations of
optimization paths: Fastest, Snake Y, Snake X, One Way Y, One Way X
and User defined. Choosing one of them determines the way the cut will
be made.
o Stripe width in this field you can set the width of the Stripes, that will be
optimized, before the machine will move to the next stripe.
o Cooling distance here you can define the minimum Cooling Distance
between the future cuts.
For each choice you make, you will be shown a corresponding icon in the tools
record on the Used Tool dialog:
94
Punching Manual
After you finish defining all the tools, you will see the corresponding icon for each
tools strategy:
95
cncKad
3.2.3.3
Reposition Types
There are three options of reposition types:

Global
Max at 1st grip
Max at Last grip
For more information on these options, go to Max/Min Processing section of CAM
Menu chapter of this manual.
3.2.4
Delete Tool
Clicking this button removes selected tool from the current processing.
3.2.5
Make Optimization
This option activates the optimization algorithm, which recalculates the processing
sequence making any changes, e.g. defining tool-specific optimizations.
3.2.6
Ordering the CAMs
After placing your CAMs, you can rearrange the order in which the entities will be
processed.
Mark one of the tools in the dialog, and then click one of the following buttons:
Order by List to rearrange the processing according to a list of the entities
processed by the tool.
Order by Mouse to graphically rearrange the processing on the part itself.
3.2.6.1
Ordering by List
You will be presented with your part and a list of the entities processed with selected
tool (the number of entities is shown in the Hits field of Used Tools dialog):
96
Punching Manual
As you move the cursor inside the list, each corresponding entity will be highlighted.
To change the order of the processing, mark an entitys number and with the arrows
move it up or down inside the list. When you move to the desired position, click Done
button to see the change. After you finish setting the order for all the instances of the
tool, confirm changes clicking OK button. If you want to resign from changes, click
the Cancel button.
3.2.6.2
Ordering by Mouse
After clicking this button you will be presented with your part and with marked and
numbered entities processed by this tool.
To determine the ordering, click the entity you wish to be processed first, then the
second, and so on. After arranging the processing sequence of entities, you will be
returned to the previous dialog.
3.2.7
Sorting by Stations
You can sort the tools, used on the part, by their stations, clicking Stations column
heading.
The tools will be organized in a sequence designated to minimize turret rotation the
trimming tool will be placed last, then the tool nearest to it, then the tool nearest to
that one, and so on for the rest of the tools.
3.2.8
Sorting by Type
You can also sort the tools by their types, clicking Current Tool column heading. The
tools will be grouped by round, oblong, rectangular (which includes also square tools)
shapes etc. Within each group the tools will be arranged by their size.
3.2.9
Locking Stations
If you want the tool to be assigned to the station no matter what, you can lock/un-lock
all the stations with a click on the Lock Station column heading.
3.2.10
Die Selection in Used Tools
In the Die section of the Used Tools dialog, the most appropriate die (if such exists)
out of the dies' list entered in the Tool Library is displayed for each tool.
The considerations taken into account for the choice of the suitable die depend on
the sheets thickness and on the definitions entered in the Material list for the
current Sheet type (see Workspace Settings dialog => Material tab => Edit
material button): the Dies clearance cannot be below or above the minimum and
maximum percent clearances of that sheets thickness, and it will be as close as
possible to the Best Clearance defined.
97
cncKad
However, if you wish to change this decision, or to enter a die for a tool directly into
the Used Tools dialog, just click on the Die column of selected tool, ignore the
dropdown list that appears and simply type-in the desired clearance. As you do, the
Lock Die checkbox (in the nearby column) will be automatically checked, meaning
that the value just entered will be kept.
3.2.11
Tool Functions
This option allows you to set functions for a specific tool. They will be enumerated in
the Functions column; when there is not enough room to preview all the functions
set for a tool, you can see them as a tool-tip when you lower the cursor over the cell:
For more information on this subject, please refer to the Defining Tool Functions
section of CAM Menu chapter of this Manual.
3.2.12
Group/Ungroup
This option allows you to group together a number of tools, making them subject to
the same optimization strategy. This feature is especially practical in those instances
where it is important to use a number of tools in the same sequence, for example:
when you are using two (or more) forming tools, where it is advisable to punch from
the clamps outwards and not make several passes. In such a case you can group
these forming tools together, and set an Optimization Strategy of Snake X and
Starting Corner of Bottom Left, both tools will be optimized together.
3.2.13
Turret Setups section
This section of the Used Tools dialog deals with the usage of Turret Setups and NC
files:
Use Current NC checking or unchecking this option determines if an
existing NC file will be used instead of creating a new one.
NC exists this check-box in not available for editing. It indicates if there is
an existing NC file to use for current DFT.
Setup Window this dropdown menu allows you to choose which setup file,
from existing ones, to use.
Create Setup From Used Tools clicking this button allows user to save
current list of used tools as a new tools setup.
3.3
Create a Special Tool File
When you choose this option you are in fact attempting to define a new tool.
Before doing this you need to follow a few steps:
1. View the Tool Definitions.
2. Follow the directions outlined in Creating User Defined Tools.
3. Make sure to view the rules for naming tool files.
3.3.1
Tool Definitions
There are several types of tools, each defined by the shape of the tool and the
parameters that define it.
The following describes the parameters for defining the various tools:
98
RO Circular tools
RE Rectangular tools
Punching Manual
RR Rounded Rectangle
SQ Square tools
OB Oval or Oblong tools
TR Triangular tools
SD D shaped tools (Single D)
DD Double-D shaped tools
CR Corner Radius tools
MJ Micro Joint tools
F Special tools, user defined
3.3.1.1
Circular Tool
Definition: RO 20
Where 20 is the circle diameter.
3.3.1.2
Rectangular Tool
Definition: RE 40 15 30
Where 40 is the length, 15 the width and 30 the declination of the Rectangle (if you
do not define an angle, it will be set as 0).
3.3.1.3
Rounded Rectangle
Definition: RR 40 15 2 45
Where 40 is the length, 15 the width, 2 the radius of the corners and 45 the
declination of the Rectangle (if you do not define an angle, it will be set as 0).
99
cncKad
3.3.1.4
Square Tool
Definition: SQ 40 15
Where 40 is the side and 15 the declination of the Square (if you do not define an
angle, it will be set as 0).
Usually, the angle is left at 0, or defined as 45.
3.3.1.5
Oval Tool
Ovals are rectangles, with half-circles as two of the sides.

Definition: OB 40 15
Where 40 is the length of the oval 15 is the width (the diameter of the arcs).
You can also give this tool a declination, e.g. OB 40 15 45.
3.3.1.6
Triangular Tool
Definition: TR 30 50 13
Where 30 is the basis, 50 is height and 13 is the center of the triangles bounding
circle.
100
Punching Manual
3.3.1.7
D Shaped Tool
D shapes are cut circles, and the D-shape will be located on the part by its straight
side, not the circular one!
Definition: SD 40 35
Where 40 is the diameter and 35 is the width, measured from the straight side to the
opposite rim of the circle.
You can also give this tool a declination, e.g. SD 40 35 45.
3.3.1.8
Double D Shaped Tool
Double-D shapes are circles cut on opposite sides, and the shape will be located on
the part by its straight side, not the circular one!
Definition: DD 40 35
Where 40 is the diameter and 35 is the width, measured from one straight side to the
opposite one.
You can also give this tool a declination, e.g. DD 40 35 45.
3.3.1.9
Corner Radius Tool
The main use for these tools is to punch Fillet outlines.

Definition: CR 3.5 20 20 6 6
Where 3.5 is the fillet diameter, 20 horizontal length, 20 vertical length, 6 horizontal
cutting width and 6 vertical cutting width.
101
cncKad
3.3.1.10
Special Tools
While adding a new special tool to the library it is important to pay attention to
naming them. It is substantial, since various machines "understand" only the precise
naming and if the tools won't be given proper names, the machine will not be able to
find them in the library.
The standard tool library supplied with cncKad contains a variety of special tools like:
Beading Tools
Embossing Tools
Slitting Tools
Forming Tools
Tapping Tools
Wilson Wheel Tools and others.
For more information on the special tools see the Names for Special Tool Files
section of this chapter.
3.3.2
Creating User Defined Tools
Here you will learn how to define a special tool whose parameters do not fit the
ones available in the Tool Library. In this example we will be creating a new radius
tool. All you have to do is to follow procedure described below.
This procedure will be divided into three stages:
1. Creating the outline of the tool
2. Adding the new tool to the Tool Library
3. The Tool Reference Line
And at the end we will Test the New Special Tool we just created.
3.3.2.1
Creating the outline of the tool
The first stage of creating a new tool is to draw its outline of the tool as a regular DFT
part.:
102
Punching Manual
1. Open a new part. Give it the name of the intended tool, e.g. "radius10.dft",
and save it in the ..\Metalix\P\TOOL-DFT folder:
Important: The name must not contain spaces.

2. The size you define here is not really important, so you can enter any values
here. For this example we will set X=20, Y=20:
3. Now from Shapes Toolbar we will choose the Draw Rectangle option. The
103
cncKad
Type the values as presented in the dialog, and click OK button.

4. The center of highlighted, with blue color, rectangle will appear on the cursor
crosshairs. Click the cursor at the beginning of the origin coordinates (0,0).
The centre of rectangle will be placed in (0,0).
5. If the following dialog will appear asking you whether you want to punch the
shape with fitting tool, choose NO for an answer.
6. Press Esc key, to leave the Draw Rectangle command.

7. Now delete the bigger contour, click the
drawing, clicking the
104
button, and then refresh the
button. This is the picture you should see on your
Punching Manual
screen now:
8. Now from the Shapes Toolbar select Draw Circle button. Type the diameter
value as 5 and click OK button.
9. Now with the circle's middle point click the right bottom corner of the
rectangle. And then press Esc key, to leave the Draw Rectangle command.
10. Refresh the drawing, clicking the
button. Now from Edit Toolbar select
the Trim button. The drawing will be highlighted in blue color.
11. Click the lines, as marked on the picture below:
Now press Esc key to escape the command, and Save your drawing.
3.3.2.2 Adding the new tool to the Tool Library

Now we will add the new tool to the Tool Library:
1. From the Tools Menu choose Create Special Tool File:
2. The following dialog will open:
105
cncKad
Note that the name of the new tool is the same as the one you defined for
the DFT part, and that it will be saved in the ..\Machines folder.
3. Don't forget to Save the new tool.
3.3.2.3
The Tool Reference Line
Now you must choose the entity of the tool the Tool Reference Line, according to
which the punch with this new tool will be placed on the part.
1. Click on the radius and it will be marked in red, and the rest of the tool will be
marked in blue.
Important: If the tool includes more than one contour (such as a Cluster
Tool), click all of them.
106
Punching Manual
2. Press Enter key to confirm the chosen contour(s), and the following dialog
will appear:
3. Click Add to tool library button, and the tool will be added to the Tool
Library.
4. Check that you have indeed added a new tool to the library: Click the No Tool
button on the State Bar, and the Tool Library will open. Go to the F tab and
scroll down to the new tool:
Whenever you choose a special tool to process with, its representation will appear on
the Tool Display, with the Tool Reference Line highlighted in red:
107
cncKad
There also is an option of changing the Tool Reference Line location: toggle on the
Index button on the Info bar and then press the S key: the red line on the tool
indicating the Tool Reference Line will move to the next side of the tool. Press the S
key until you are satisfied with the cutting lines location on the tool and then proceed
with the punch. If needed, the tool will be indexed.
Notice that you can also select two parallel lines on the tool as Reference lines: the
program will then choose which one is best, with major concern of avoiding using the
Auto Index function.
3.3.2.4
Testing the New Special Tool
1. Open the part you want to process.

This will be our notch, which we want to process with the new special tool:
2. From the Common Toolbar click the Add Punch button. In the dialog which
will open, click the Tool button. In the Tool Selecting dialog, which will
appear, go to the Special Tools tab (F) and choose the tool you have just
added to the library:
Click OK button to confirm your selection.

3. Turn the Index Button On, and press the S key to toggle the Tool Reference
Line, highlighted in red (on the gray background this line will be highlighted in
blue). When you will are satisfied with the cutting lines location on the tool,
108
Punching Manual
proceed with the punch:
4. Now, in the same way, place the second punch:
5. The processing results of our notch will look this way:
3.3.3
Names for Special Tool Files
Different tool files have different names and there are several categories of tools.
Therefore it is important to give special tools proper names, since various machines
"understand" only the precise naming.
Below you will see find more information on Forming Tools, Tapping Tools and
Wilson Wheel Tools.
3.3.3.1
Forming Tools
Use the format FTL<dd>, where each "d" is a digit.

For example FTL27.T
After the number, you can include some relevant info, e.g. a forming tool that is used
before an M4 Tapping tool will be named this way:
FTL54-PreM4.T
3.3.3.2
Tapping Tools
The names for these tools are pre-defined; there are two types of Tapping tools:
MM Tapping tools
Inch Tapping tools
3.3.3.2.1
MM Tapping Tools
The following tools are available for mm tapping:

TAP52-M25
TAP53-M3
TAP54-M4
TAP55-M5
TAP56-M6
TAP58-M8
3.3.3.2.2
Inch Tapping Tools
The following tools are available for inches tapping:

109
cncKad
TAP256
TAP348
TAP440
TAP540
TAP632
TAP832
TAP1032
3.3.3.3
Wilson Wheel Tools
In cncKad the following Wilson Wheel tools are available:

WW01.T - Wilson Rolling Shear
WW02.T - Wilson Rolling Rib
WW03.T - Wilson Rolling Offset
WW04.T - Wilson Rolling Louver
WW05.T - Wilson Rolling Pincher
For use with Fanuc controls they are named this way:
WW01
WW02
WW03 and so on.
For use with Siemens and Nisshnibo, they look this way:
WW11
WW12
WW13 and so on.
Below you can see an example of Rounded Rectangle (200mm x 100mm, R=50mm)
processed with WW12:
110
Punching Manual
3.4
Turret Setups
After you click this option, the following dialog will be displayed:
3.4.1
Machine section
Options of this section allow you to choose, from the list of installed machines, a
Machine for which you would like to create new Turret Setups or edit already existing
ones.
3.4.2
Setup File section
Here the user can determine settings for his turret's setup file, a file that describes
how tools are arranged in the machines turret.
3.4.2.1
Select Setup File
From this dropdown list you can choose one of the existing setup files.
3.4.2.2
Creating a New Setup
Click on the Add/Create New button.

You will be asked to provide a name for the new turret setup file. The file name can
be any name you choose; no extension is needed, since one will be set by default, as
the machine ID character followed by ET. For instance if you machine ID character
is V, then the extension for the setup file will be ".VET". The user can create as many
Turret Setup files as needed.
After doing so, choose the new setup from the dropdown list and click Edit Setup
button. A dialog will open, giving you possibilities of defining various parameters for
your turret.
3.4.2.3
The LASTSET File
This setup differs from others, so it is important to explain it more thoroughly.

What distinguishes this file from other turret setups is that it always is a
representation of the exact tool arrangement in the machine and reflects the turret
setup of the last NC (there is one exception to this rule, as we will later see).
The LASTSET file is an alternative to the "whiteboard" often found next to
machines, which machine operators use to update the current tools in
the turret.
Since it shows which tools are currently available in the machine, the LASTSET
feature is useful in two important ways:
111
cncKad
it automatically calculates which changes the machine operators must make

in the tooling in order to produce the next part.
it helps the engineers in tool selection when processing parts different tools
may often be used for the same job, and intelligent selection helps minimize
tool changes (i.e. time).
3.4.2.3.1
Creating the LASTSET file
To create the file, select the LASTSET option from the Select Setup file dropdown list
(shown above) and click the Edit Setup button. This will open the file and you will be
able to edit it now:
The initial values will be displayed according to the turret file selected for the
machine.
3.4.2.3.2
Using the LASTSET file
In order to see how using the LASTSET file helps machine operators with their work,
we will use the following example:
We have created a LASTSET file according to our turret tooling, and now we will
process a part that requires using a RO 5 tool that currently is NOT in the turret.
To use the LASTSET option, you must first enable it on the Working Defaults tab of
the Workspace Settings dialog:
Important:
Only workstations that are on the actual production floor and are used
for sending NC to the machine may use this option!
If you wish to generate NC simply to view the Graphic Simulation, do not enable this
option (concerns workstations e.g. in engineering or design departments).
112
Punching Manual
After enabling the above mentioned option, we can start the Post Processing
procedure. In one of its steps, we come to the Used Tools dialog; here we must
select LASTSET as the Turret Setup:
This will ensure that if you processed your part with a tool that is already in your
machine (and therefore assigned to a station in LASTSET), the correct station will be
chosen for this tool in the NC, and thus this will minimize changes to the turrets
tooling.
Next step is the Post Processor Options dialog; here we must enable the following
option:
This will cause cncKad to examine the part you want to Post Process, and check if
NC code can be generated using the selected turret setup (i.e. the LASTSET file).
If this is impossible (in this case because there is a tool missing from the setup),
cncKad will update LASTSET to include the new tool arrangement needed to
generate the NC, and then it will issue a warning:
Important:
This is not an idle warning it means that the machine operator must
change the tool arrangement in the turret, so that it corresponds to the
new setup created.
This is the only time that LASTSET does not match the turret, and thus
must be corrected as soon as possible!
To help in making the necessary adjustment, cncKad will include instructions inside
the NC file the word NEW will be added for stations that require it (with changed or
added tool):
In this case, we must put an RO 5 tool into station number 226.

In addition, an asterisk (*) sign will be inserted into the Report File next to any
station that needs correction:
113
cncKad
Only after we make the specified change, and LASTSET is once again a true
representation of the turret, we can produce the part we designed.
3.4.2.4
Save Setup As
Choosing this option gives you an opportunity of saving current setup file under a
new name.
3.4.2.5
Editing an Existing Setup
To edit an existing Setup File, use the dropdown menu to find the one you want to
use, and click Edit Setup button. The following dialog will open:
The Station column reflects the number of the turret station.

The Fixed column allows you to choose the station which all the time would
be assigned and locked for a specific tool.
To place a specific tool in a station, click the Setup Tool column field for this
station; the Tool Selecting dialog will open and you will be able to choose the
desired tool.
Important: You must set the tools in such way, so that the file will describe
the exact arrangement of tools sitting currently in your machines turret.
114
After you have assigned a tool to a station, you can ascribe Functions to it
click the Functions field, and you will be presented with the Tool Functions
selection dialog.
Punching Manual
In Clearance column you will see if any clearance was ascribed for current
tool.
The Type field displays information on the type of the station. E.g. looking at
this field you can see whether the station is specified for round tools only
and if it is an Auto Index station or a normal one.
The Size and Size Type columns give information about the size of the
station accordingly the tool size for this station (how big tools can fit in) and
the Standard annotation for the corresponding tool size (denotes the station
type by a letter).
Multi-tool column displays the number of a Multi-Tool station, if you have
such.
Notice that the data in this dialog can be sorted per column: just click on one
of the columns headings and the entire file will be sorted in the ascending or
descending order according to that column.
After you have finished defining the tools, do not forget to click Save button to
preserve your selections and Print it, if you want.
There are few more options in this dialog the user can Insert or Delete
row(s), Remove Tool, Restore Default Order of the tools, or Cancel the
changes he made.
Clicking the Switch To Setup Layout button you will be moved to the Turret
Display dialog.
It is important to note that each machine has its own turret setups, so that if you have
created a new setup for machine P, machine V will not have access to it.
3.4.2.6
Editing the ToolFunc File
You can edit the ToolFunc.?ET (where ? stands for the machines ID character), by
clicking the Add/Edit ToolFunc button. The following dialog will open:
115
cncKad
This table consists of the following fields:

The Station column should be permanently set to -1. This means that the tool
can be placed in any station of the machine turret.
The Fixed column allows you to choose the station which all the time would
be assigned and locked for a specific tool.
The Setup tool column displays the tool name, e.g.: F LUVER.T. You can fill
this field in by clicking it. The Tool Selecting dialog will appear and you will
be able to choose the desired tool:
116
Punching Manual
In the Functions column you can choose the desired function the same way
as you selected the tool. On the beneath picture you will find an example of
functions assigned to tool RE 20 10.
After you have finished defining the settings, click Save button to preserve your
selections. From now on, whenever the defined tool is used, the chosen functions will
be added to NC program.
3.4.2.7
Removing an Existing Setup
The user can delete selected setup file by clicking the Remove Setup button. A
following warning message will pop-up, asking you if you are sure of your decision:
117
cncKad
Confirm your action clicking OK button and the currently chosen setup will be
removed.
3.4.2.8
Turret Display
Pressing this button will open the following dialog showing the turret with tools
assigned to stations; by each of the station its number will be displayed:
On the panel situated on the right side of this dialog you will find options with which
you can manipulate the turret's stations.
3.4.2.8.1
Station number field
When you click any station instance with the cursor, it will be marked with red color
and its number will appear here.
3.4.2.8.2
118
Tool Preview
Punching Manual
In this window you will be able to preview the tool selected on the Tools' List.
3.4.2.8.3
Tools' List
Here you will see a list of tools assigned to selected station.
3.4.2.8.4
Functions' List
Here you can see a list of functions assigned to the currently marked tool in the
Tool's List.
3.4.2.8.5
Adding Tool
Clicking the Add Tool button you will be redirected to tools' library dialog, where
you will be able to choose the tool you wish to add to certain station.
3.4.2.8.6
Removing Tool
Clicking the Remove Tool button causes the tool to disappear from selected station.
3.4.2.8.7
Changing Tool
Clicking the Change Tool button redirects you to tools' library dialog, where you
can select different tool for the current station.
3.4.2.8.8
Tool Functions
Choosing this button opens the Tool Functions dialog, from which you will be able
to assign new functions for tool or edit the existing ones.
More on this option you will find in Defining Tool Functions section of CAM Menu
chapter of this Manual.
3.4.2.8.9
Fix Station
Marking this checkbox, you decide that the tool ascribed to the currently selected
station will be used only with it.
3.4.2.8.10
Switch To Setup List
Clicking this button you will be transferred to the Setup File dialog.
3.4.2.8.11
Radial View
Checking this box you change the turret display. Now all the tools will be viewed as
placed in the stations along the turret tracks.
Normal View
3.4.3
Radial View
Multi-Tools section
This section is available for machines which have Master turrets with Multi-Tools
option, e.g. Finnpower, LVD, Strippit, Rainer and Muratec machines.
119
cncKad
You should chose Master Turret for your machine in Settings => Machine Settings
=> Machine tab => Machine Settings dialog:
Your choice done there will be available in Multi-Tools section, where you will be
able to select and manipulate it, with the usage of following buttons:
Add/Create a New Turret
Edit Turret
Remove Turret
3.4.3.1
Add/Create a New Turret
When you click this button a Save As window will appear. Type the new name for the
multi-tool turret settings. It is recommended to type in the new name with "U_" in
order not to override an existing turret and also to differentiate it from regular turrets.
For example: U_CosFinn.
After doing so, click Open button. You will be returned back to the Turret Setups
dialog, and the new multi-tool turret will be shown in the dropdown list as a default:
In order to enter the desired changes, click the Edit Turret button.
3.4.3.2
Edit Turret
After clicking the Edit Turret button, you will be presented with the following dialog,
allowing you to personalize the mutli-tool turret:
120
Punching Manual
The active station, we are defining settings for, is marked with red color.
The legend on the left side of the dialog specifies the colors of the stations according
to their sizes, as well as denotes the Irregular, Multi-Tool and Round Only stations.
On the right side of the window you can see various settings options for the selected
station:
3.4.3.2.1
Station Number
This field displays the number of the presently chosen station. The multi-tool stations'
numbering varies for machines.
More information on the Multi-tool Numbering you will find in Changing Turret
Numbering section of Appendix chapter of this manual.
3.4.3.2.2
Track
Here you can view and change the track for the current station. It is by default set on
2.
3.4.3.2.3
Station Size
From the dropdown list you can choose the best definition of your station size.
3.4.3.2.4
Station Angle
In this field you can see, as well as edit, the station's angle in turret from 0 to 360.
3.4.3.2.5
Auto Index
Checking this box we denote the station as rotating one. Choosing it makes the 90
Degrees Only option available.
3.4.3.2.6
90 Degrees Only
121
cncKad
This option is valid only for Auto Index station and allows rotating the index station
only at 90 degrees.
3.4.3.2.7
Round Only
Marking this checkbox the user denotes the station available only for round tools.
3.4.3.2.8
Multi-Tool
Notice (on the picture shown in Edit Turret section) that in Master Turrets there are
no Multi-Tools as a default; therefore they should be added. Check the Multi-Tool
box and from the dropdown list detailing Multi-Tools available for this turret select the
desired one.
In most turrets not all of the stations can be changed into Multi-Tool stations. It is
possible though to add Multi-Tools to more than one station. To see what options can
be edited for some station, just click on it and see on the right section of the dialog
what options are available.
After choosing the desired Multi-Tool, as you can see on the picture presented
below, it is not possible now to change the track and the size of Multi-Tool stations.
Only Auto Index option can be chosen and if you choose it the Round Only option
will be also activated.
If you would like to change other station properties, like track, size or angle please do
so before adding the Multi-Tool to it.
3.4.3.3
Remove Turret
Clicking this button deletes currently selected turret.
122
Punching Manual
3.5
Convert Old Boschert Tools

This option is available for Boschert machines only.
Before, in older versions of cncKad, the tools didn't have ToolN and their number
was being taken from the station. So if you were using the old tools and recently
have updated your cncKad to the new version, this converter is for you.
For more information on converting old Boschert Tools and adjusting them for work
with cncKad, go to Release Notes for BOSCHERT users section of Appendix
chapter of this manual.
123
cncKad
4 NC Program Creation
There are several stages and options you must go through, leading up to the postprocessing stage, where the NC program is being created out of a part.
4.1
Creating the Program
Once you have finished assigning punches to your part and all the settings have
been defined, you are ready to start the final phase of program development. In this
stage cncKad will read the graphics, which you have processed, and convert it into a
program in a language that your machine controller can recognize, and which can be
simulated or/and sent to a machine.
Post Processing is a multi-part procedure. This chapter takes you through it step by
step.
4.2
NC Generation Stage 1
From the File Menu, select the Post-Process option or on the Common Toolbar click
the Post Processing button
.
If you hold down the CTRL key, as you click the NC button, the postprocessor will
skip stages 2-4, and jump straight to Stage 5. Otherwise, the following dialog will be
displayed:
The User Data that you fill in will be used in the Report File. Entering this data here
is not compulsory, unless you wish to produce a report file.
You can use the Copy and Paste buttons to transfer the users details between
parts. There is also a possibility to Edit Titles.
After you are done with filling in the details click the Next button.
For more information on the features of this dialog refer to appropriate section of
CAM Menu chapter.
4.3
In this stage, you can see for which machine the program is being created.
124
Punching Manual
If you have more than one machine installed on your workstation, this enables you
make sure you have selected the correct one. If everything is all right, click the Next
button.
4.4
In this stage the Used Tools dialog is being displayed, allowing you to set the order
of the tools as well as defining other settings for them.
It is advisable to make all major changes to the cutting at this stage.
To go to the succeeding stage, click the Next button.
4.5
This is the final dialog before the generation of the code. Here, you can set various
options pertaining to the code generation:
125
cncKad
4.5.1
Use Macros (Sub-Routines)
This option is available only for machines which support it.

It's very useful when using multiple parts on a single sheet, because it allows the
user to shorten the program by using macros (or in other terminology SubRoutines). Selecting this checkbox will enable them.
If you want to set the Macros as a default for your machine, go to Post-Processor
Options tab of the Workspace Settings menu in the Settings chapter of Drafting and
Nesting Manual.
4.5.2
Automatic Testing of Common Cuts
If Common Cuts option is chosen, this function will check for duplicates it will
make sure that between two adjoining parts no double CAMs have been placed.
4.5.3
Use Controller Compensation

This option is available only for laser and combined (punch-laser or punchplazma) machines.
It is useful in case you want to get CRS (Cut Radius Compensation) in NC command.
4.5.4
Report File Creation Options
From this dropdown list the user can define the default setting for creating a Report
File. The options are as follows:
Do Not Create Report File
Create Report File
Print Report File
Create and Print Report File
More information on creating Report File and the types of Report Templates you
can find in Appendix chapter of this manual.
4.5.5
Update LASTSET
This option is available only when the Enable update of LASTSET
checkbox is selected in Working Defaults tab of Workspace Settings
dialog.
If you check this option, the current Turret Setup will be saved as a Setup File called
LASTSET.?et (where ? stands for the machines ID character). If you are working
with such a file right now, and you made a few changes you would like to keep for
processing other parts, checking this option will update it.
You can use this setup for the next part you create, being certain that in both cases
parts use exactly the same setup.
4.5.6
Run Simulation After Post Processor
After the Post Processing stage the graphic creation will remain open, and the
simulation of created program will be loaded in a separate module, where the user
will be able to test the program and make sure it runs with no problems.
126
Punching Manual
4.5.7
Automatic Detection
This function is available for punching machines only.
Here you can choose one of the few options for automatic parts' processing:
Do not detect groups of single punches
Automatically detect lines of single punches
Automatically detect grids
More information on these features you will find in Automatic Detection section of
Settings chapter of Drafting and Nesting Manual.
The only difference between the parameters set on there and here is that the settings
selected here concern only the currently created NC Program.
4.5.8
Program Number
Some machine controllers demand, that there be a program number, others do not.
That's why here the user can define a default program number.
4.5.9
Sheets Quantity
The user can set here the number of sheets he wants to process this time.
If the checkbox Update Sheet Quantities in DB will be selected, the Number of
Sheets entered here will be deducted from the quantity of sheets entered in Select
Sheet dialog which is accessed from Sheet tab of the Set Sheets and Clamps
window.
4.5.10
Sheet Loading
In this section of the dialog, the setting definitions are being loaded from
Load/Unload tab of the Set Sheets and Clamps window.
This is the last moment and your last chance for entering changes for sheet loading,
before the NC code will be generated.
127
cncKad
4.5.11
Name and Path of NC file
From this dialog the user can set the name and path for the NC file. The NC file can
be given a different name than the drawing file and placed in a different directory. To
select a directory, click the Browse button.
When you have defined all the settings, click the Finish button.
4.6
The following dialog will be opened:
This is the code generation stage, during which you might be asked different
questions concerning your machine. Clicking Enter button usually attains the default
values.
If the Post-Processor could not create the program or there are problems with the
clamps or the tools, you will also be notified about them by an appropriate message.
If you placed CAMs within the clamps dead zone and the Clamp Avoidance option is
activated, you will be able to decide whether to attempt avoiding clamps or to
continue without any automatic clamps avoidance.
If you requested to print the report file, you will have to prepare the printer and, when
requested, press a key to print it.
When the Post Processing stage is over, click the OK button to open the simulation
module.
128
Punching Manual
5 NC Code Simulation and Editing

This chapter deals with cncKads simulation program.
The Simulation program is a completely individual module of cncKad and is run
separately from the main program the simulation is loaded into a separate window
allowing cncKad to remain open in the original window.
The following pages explain the options that can be used here, and how to run the
simulation.
5.1
Opening the Simulation
There are three possibilities of opening SimW:

After Post Processing
When Simulation is selected from the File Menu within cncKad.
From the Start => Programs => Metalix =>Simulation menu
In any case, the following window is loaded:
The graphic results of the code are displayed on the left side of the screen.
Any change in the code displayed on the right side of the screen will be updated on
its graphic representation.
5.2
Running the Simulation
Once an NC code and graphics are visible on the screen, that code can be
simulated.
If there was no file loaded when you entered the simulation module, from File Menu
you can Open the file you want to simulate.
The progress of the Simulation is controlled in two ways:
129
cncKad
From the Execute menu:
From the Execute toolbar:

.
5.2.1
Starting the Simulation
Click the
button to begin the Simulation, or to resume it after it has been paused.
If you want to run the program line by line, click the Line = ON button on the left side
of the screen and then click the Run button repeatedly.
5.2.2
Pausing the Simulation
Click the
button to temporarily suspend the Simulation.
If you now click the
5.2.3
button, the Simulation will resume from its current position.
Stopping the Simulation
Click the
button to stop the Simulation.

If you Stop the Simulation, it cannot be resumed from the same position,
but will start from the beginning, when you Run it again.
5.2.4
Simulation Speed
The user can define the simulation velocity that suits his needs, before the simulation
is run, as well as during it.
To do this move the mouse on the speed slider to the left for slower speed, and to
the right for faster speed:
The speed will be updated in effect only after the current line has been
executed.
5.2.5
Simulation Time
This window shows the time it will take to run this NC program on your machine.
The time displayed here varies for different machines. In the time factor there are
various elements taken into account, such as X and Y travel time, turret rotation
speed, tool placement within the turret, repositioning and tool change time.
5.3
Simulation Screen Elements
There are three elements in the Simulation screen:

a The State Bar
b The Graphic Simulation area
c The NC Code Editing area
130
Punching Manual
5.3.1
The State Bar
This is the area on the left side of the screen, containing different settings and
information pertaining to the Simulation.
5.3.1.1
Snap Button
This button gives a variety of Snap options, giving the user a choice of choosing the
most desired one.
More information concerning this feature you will find in Snapping on an Entity
section of Introduction chapter in Drafting and Nesting Manual.
5.3.1.2
Dim Button
This button enables or disables viewing Dimensions and Text on the part.
Dimensions that have been placed on the drawing during the drafting stage can be
toggled ON and OFF by clicking the
5.3.1.3
button on the State Bar.
Tool Button
If this button is in the ON state, the program will pause every time there is a change
tool command in the code. Each tool's preview is being displayed in the tool port.
To continue running of the program, click the appropriate button in the Execute
toolbar.
5.3.1.4
Stop Button
If there is a Stop Machine command defined in the program, this button enables and
disables that Stop (for the Simulations run):
131
cncKad
When it is in the OFF state, the Simulation will not halt for any stop commands, (on a
lot of machines the stop command is M00), however when it is in the ON state, the
simulation will pause every time a stop command is encountered. To continue with
the simulation, click the appropriate button.
5.3.1.5
Clamp Button
This button enables or disables the warnings that are issued when the Clamps' Dead
Zone is entered:
In the OFF state, the Simulation will run without any pauses, even if the tool enters a
Dead Zone.
Note: If the tool damages the Clamps, a warning will be issued and the
program will pause running.
However in the ON state, the Simulation will pause every time the tool enters the
Clamps' Dead Zone. The tool might not be damaging the Clamps, but the warning is
issued, so that you would be aware that the tool is now working in the area of the
Clamps.
5.3.1.6
OBS Button
This option is a button of Optional Block Skip feature and appears on most of the
machines. Its function is to allow the program to ignore or execute lines that have
double slashes before them, e.g.:
Y527.
X78.
//G72X61.5Y564.5
//G66I8.J180.P-5.K8.T217 (R 5. 5.)
//G72X253.5Y564.5
G66I8.J0.P5.K8.
When this button is in the ON state, the lines with double slashes before them will be
ignored (not executed), but when this button is in the OFF state, these lines will be
executed.
5.3.1.7
Cursor Coordinates
This section shows the coordinates of the cursor's current position, when it is being
moved inside the graphics area of the Simulation screen:
5.3.1.8
Program Information
These coordinates show the current position of the turret in the graphics area of the
Simulation screen, when the simulation is being run:
5.3.1.9
Line section
In this section of the State Bar you can see the station number the current tool is
using, and a number of the line it is presently processing:
132
Punching Manual
5.3.1.10
Tool information
The square port displays a graphic representation of the tool that is currently being
used for sheet processing, as well as the station number it is placed in and the button
displays its name:
If you click the button, a list of all the tools that are used in the program will be
displayed, together with the station numbers there are placed in:
5.3.2
NC Code Editing
The NC code is displayed on the right side of the screen, and can be edited from this
area. If the user makes changes to the code, the graphic display will be updated
automatically to reflect these changes.
In order to edit the code select a line you want to edit, modify it and then from the
keyboard presses Enter key, so that the changes made to the current line would be
updated on the graphic display.
The editing commands, available from the Edit Toolbar
, are:
Inserting a new line
Deleting a line
Inserting a G Code (Pattern)
Marking a CAM
Send to machine (DNC)

Note: The Edit Toolbar is activated only when the user clicks the cursor in
the NC code side of the screen.
Send NC to Diskette
Searching List
Find Previous
133
cncKad
Find Next
5.3.2.1
Insert a New Line
Place the cursor on the line of code before which you want to insert the new line and
click the Insert Line button
5.3.2.2
Delete a Line
Place the cursor on the line you wish to delete and click the Delete Line button
.
5.3.2.3
Insert a G Code (Pattern)
Place the cursor at the position at which you wish to insert a G-Code and click the
. A following dialog will appear, where you will be able to enter
pattern button
the desired G-Code:
When you have finished, click the OK button.
5.3.2.4
Mark a CAM
If you want to find out how a specific line of code is being represented in the graphic
simulation click on a line of code and then click the
large cross) will jump to the corresponding CAM.
button. Simulation marker (a
Note: To see an additional CAM, repeat the preceding procedure.
5.3.2.5
Send to machine (DNC)
The
button sends the NC code to DNC program, so that it can be remotely
transmitted to the machine.
5.3.2.6
Send NC to Diskette
Choosing the
button you can send the NC code to a diskette, so that it can be
transferred to the machine.
5.3.2.7
Searching List
To this field
you can enter the value you are looking for in the
NC code. When you press Enter key, you will be transferred to the line of the code
containing this value. By the use of below described buttons, you can look for further
instances of this value.
5.3.2.8
Find Previous
When you click the

button, the last found instance of the value typed in
Searching List will be marked in the NC code
134
Punching Manual
5.3.2.9
Find Next
When you click the

button, the next found instance of the value typed in
Searching List will be marked in the NC code.
5.3.3
Graphic Simulation
The Graphic Simulation area allows the user to preview how the NC code will be
run on the machine.
When the Simulation is run, the Simulation marker (a large cross) shows the graphic
position of each line of code, as it is performed.
There are several various options that enable the user to manipulate the display, and
they can be accessed from the Zoom
and Graf
toolbars, as well as from the View menu:
5.3.3.1
Toolbar...
This option is used to customize the toolbars.

More information on this subject you will find in Using the Toolbars section of
Drafting and Nesting Manual, with this difference that in each cncKad module the
toolbars list and their content vary, but the general rules are the same.
5.3.3.2
Status Bar Enabled
Choosing this option makes Status Bar appear on the screen.

The Status Bar enables or disables viewing tips about the option you are selecting
(outlined below):
135
cncKad
5.3.3.3
Status Bar On Top
Selecting this option positions the Status Bar above the toolbars, and unchecking it
places it below the Graphic Simulation area.
5.3.3.4
Beep
This option enables or disables a beeping sound, which is used to mark each CAM
during the Simulations run.
5.3.3.5
Split
After selecting this option, the line separating the Graphic Simulation area from the
Code Editing area will follow the cursor. In order to set chosen position of the line,
click the mouse.
5.3.3.6
Zoom Part F5
This command fills the view port of the Graphic Simulation with the complete
extents of the drawing.
5.3.3.7
Zoom Sheet Ctrl+F5
This command zooms the full extents of the sheet; all instances of the part on
the sheet will be displayed.
5.3.3.8
Zoom Window F6
This command zooms into an area defined by the two opposite corners of a
window.
In order to use this command place the cursor in the first corner of the area that
you wish to zoom into, click the mouse and the window will open. Now drag the
opened window to the opposite corner of the area you wish to zoom into and click the
mouse again. The area selected within the window borders will fill the viewing port of
Graphic Simulation.
5.3.3.9
Zoom In F3
Each clicking on this command enlarges the display by twice the current
magnification.
5.3.3.10
Zoom Previous
This command allows the user to return to the previous view of the Simulation.
5.3.3.11
Zoom Out F4
Each clicking on this command decreases the magnification by half the current
display.
136
Punching Manual
5.3.3.12
Zoom Realtime
This option enables you to zoom the display incrementally: after clicking this
icon, click on the draft, and then move the mouse wheel up to zoom in, or down to
zoom out.
5.3.3.13
Pan Realtime
With this option you can "grab" and move the draft on your screen to view
different sections in it click the right mouse button anywhere on the draft and move
the mouse on the screen. As long as the button is clicked, the draft will follow the
mouses movement.
5.3.3.14
Redraw F2
This command allows for refreshing the screen and the drawing on it, cleaning
any temporary markers that have been placed on the draft.
5.3.3.15
Mark Line
If you want to find out how a specific processing (punch or cut) is implemented in the
NC code, click the
button, and then click a CAM. Its corresponding line of code
will be highlighted in the NC code area.
If you want to see an NC code representation of an additional CAM, repeat the
preceding procedure.
5.3.3.16
Ask
Choose this option and click an Entity to view information about it.
You can only select Entities in the original part, and not in the multiplied
copies.
5.3.3.17
Show Clamps Bar
You should choose this option when you want to see the full extension of the Clamps
holding the sheet.
More information on this option you will find in the Clamp Bar section of
Introduction chapter in Drafting and Nesting Manual.
5.3.3.18
Fill Tools
Choosing this option the tools will be filled on the display. The result will be as shown
on the below picture:
137
cncKad
5.3.3.19
Rapid Tool Path
Choosing this option you will be able to see the path which the tool makes while
processing the sheet.
5.3.3.20
Display Bend Lines
Enabling this option will allow you viewing the bend lines if the currently processed
part was bent. If it wasn't bent no bend lines will be shown.
5.3.4
Measure
Use this option to measure distances on the part:
5.3.4.1
From Base Point
Use this option to measure distances from one point to multiple points on the part:
The first position you click the mouse sets the base point.
The second click measures the distance to the clicked position.
Thereafter, the next click clears the selection and the one after that measures new
distance.
5.3.4.2
Point to Point
Use this option to measure distances from one point on the part to another point.
5.4
The Tools Menu
These options allow you to manage and check the tool in the Simulation setup and in
incoming NC files.
5.4.1
Edit Tools Library
Here you can add or remove tools from the Tools Library.
138
Punching Manual
For a complete explanation see the appropriate section in this manual.
5.4.2
Edit Setup
Here you can edit the Simulations setup file.

Use this option to create a turret setup that corresponds to the machines
tooling.
This will be the basis for comparison with the NC files, so it has to be an
exact match for the machine.
For a complete explanation see the appropriate section in this manual
5.4.3
Check Stations
After we have created the Simulation Setup we can check NC files for
discrepancies.
To do this load an NC file, select this option and the Turret Management window will
open:
5.4.3.1
Simulation tooling
This is the Tools in Turret section of the dialog and it shows the Simulations tooling
setup which tools are specified for which station.
As noted, this is supposed to be an exact representation of the actual
tooling in the machine.
5.4.3.2
NC tooling
This is the New Tools section of the dialog and it shows the tooling as specified in
the NC file, and if there are any changes that have to be made in order for the NC to
run correctly on the machine.
139
cncKad
This can be based on a setup file in cncKad, or simply defined by whoever
processed the part.
If there are any changes to be made, they are shown in the Operation column:
Blank this station is not used in the NC.
OK this station matches the setup:
OK (NC Change) there is a discrepancy with the setup, but it can be

corrected in the NC:
Move from xxx the operator must make a change in the machine and
switch between the tool in station xxx (e.g., 141) and this tool:
CHANGE the operator must add this tool to the machine:
5.4.3.3
Settings and definitions
These allow you to change tooling definitions, display modes and the NC file.
5.4.3.3.1
Change Station for New Tool
This button is used to move tools between stations in the Simulations setup.
Click on one of the stations and click the button a dialog will open showing which
stations are available to accept this tool.
Only move them not change.
To change the tool, use the Change Turret Tool button.
There are several restrictions for moving the tools:
You can only move tools that are used in the current NC.
You can move a tool only into an appropriate station for a C sized tool, only
C and larger stations will be available.
There is also a matter of tool rotation a tool in an Index station can only
be moved to another Index station.
You cannot change to a station that is being used in the NC.
If you do not follow these restrictions, you will either get a dialog without any stations,
or none at all.
5.4.3.3.2
Change Turret Tool
This button is used to change the Simulations setup add or change tools in a
specific station.
5.4.3.3.3
Display Mode
These settings determine which stations will be shown.

5.4.3.3.3.1
All Turret
Shows all the stations in the turret.
5.4.3.3.3.2
Used Tools Only
Shows only those stations that are used for the NC (this includes those that have to
be changed in the setup).
140
Punching Manual
5.4.3.3.3.3
Changes Only
Shows only those stations that require changing tools in the setup.
5.4.3.3.4
Confirm All Turret Changes, Correct NC
This will make all the changes needed to punch the part correctly:
Add the necessary tools to the setup.
Correct the stations in the NC to match those in the (newly changed) setup.
5.4.3.3.5
Close, Do Not Update
This will close the dialog without making any changes.
5.4.4 Tooling Changes Example

Below we have a section of an NC file showing station assignment as it was
generated by cncKad:
When we use the Check Stations option, we get the following:
We see results for four tools:

RE 65 5 and RE 6 3 are in their correct stations.
SQ 30 is in the wrong station, but this does not require any change in the
turret.
RO 6 is missing from the setup (and thus from the machine) and must be
added by the operator.
After we confirm the changes, the code changes to reflect the corrected station
assignments:
141
cncKad
142
Punching Manual
6 Appendices
These topics provide explanations regarding some more advanced features in
cncKad.
6.1
The Report File
Below you will find explanations concerning Report Files and directions of how to
create them.
6.1.1
Small Introduction
A Report File is a document that provides information about a part created in

cncKad.
You can use the default Report Templates supplied with cncKads installation, or you
can create your own ones.
In order to create your own template you have to go through three stages:
o Creating a template
o Debugging it
o Testing it with cncKad
In the following pages we will be using several concepts that are important for
creating good templates:
Plaintext A file format that contains only text in a single font and nothing
else; when viewing such a file with an editor, what you see is what you get.
Windows supplies two plaintext editors Notepad and DOS Edit.
RTF A general format used by text editors to create documents with
graphics and fonts. When viewed in Word or WordPad you will see the
graphics and the fonts, but if you view such a file with a plaintext editor you
will see that it is comprised of coded text that tells WordPad how to display
the document.
DOC A format used by Microsoft Word to create documents that contain
complex graphics and fonts. When viewing such a file with a plaintext editor
you will see a lot of gibberish with some regular text strewn among it.
Attribute A characteristic of a part, such as its size, the material it is made
of, which tools are used to process it and so on.
Token A sequence of letters or numbers beginning with "@"; tokens cannot
contain spaces, and must have a space after them. Each token is unique and
represents a specific attribute of a part.
For available tokens go to: Common Tokens and Additional Tokens
sections of this chapter.
Post Process Taking a draft of a part in DFT form and turning it into an NC
file that can be sent to a machine. During the Post Process, cncKad keeps
track of the various attributes of the part and each of these features is saved
as a variable. These variables can be accessed and shown in the template
you will create.
Template A file in plaintext, RTF or DOC formats containing a document
that uses tokens to display information about a part. Each token represents a
specific variable. During the Post Process, when the template is loaded into
cncKad, the post processor recognizes these tokens in the document, and
replaces them with the values of the actual variables of parts attributes. After
the Post Processing is over the template is saved under the parts name, with
an extension denoting it as a Report File.
143
cncKad
6.1.2
Types of templates
In general, a template consists of pairings of an Attribute description followed by the

token for this attribute, for example:
Draft Number: @DRAWNUM
or
Customer Name: @CUST
Before beginning with template creation, you must decide what kind of format you
want to make.
There are three main types of templates, with pros and cons for each:
Plaintext very easy to create and debug, but limitations in font and graphics
make this kind of template plain looking.
Go to A plaintext template example section and see an example.
RTF you can create very attractive templates, with different colors and fonts
for highlighting key attributes, tables to delineate groups of attributes, etc.
Creating this kind of template is a complex process, and it is hard to debug.
Go to An RTF example section and see an example.
DOC this format allows you to utilize all the options available from Word
fonts, tables, colors, backgrounds, etc. These are the most attractive Reports,
and are very easy to create, but owing to the complexity of this file format, it
takes cncKad longer to generate the actual Reports during the Post
Processing stage.
Go to A DOC example section and see an example.
There is another type of template used in cncKad, but it is not advisable to
create templates of this type. These are DOS text templates, created
with DOS Edit.
6.1.3
Creating the Template
Before starting a template, you should decide first which attributes of the part you
want to display, and make a rough draft of it on paper.
6.1.3.1
Naming a Template
Whichever type of template you create, there is a certain naming convention you
must follow in order to allow cncKad to use it fully.
The format for template names is:
RPT_xxx_name.*
Where:
o "xxx" denotes language. Use the first three letter of the English name of
the language POR for Portuguese, SPA for Spanish, etc.
o "*" is one of the four formats used by cncKad DOC, RTF, TXT and
OEM.
It is of course possible to give different names for templates, but if you do this
cncKad will not be able to recognize it automatically in the NC Report Template
Tab of the Machine Settings dialog. See the appropriate section in Settings chapter
of Drafting and Nesting Manual.
6.1.3.2
Creating a Plaintext Template
1. Open an editor, preferably a plaintext editor such as Notepad.
144
Punching Manual
2. Type in the attributes you have chosen, leaving space for a token following
the attribute. You can use dashes and underscores to delineate attributes.
3. After each attribute write the corresponding token, making sure you leave at
least one free space before the latter one. After each token you must leave a
certain size of free space, to make a room for the attributes value.
4. The size you must leave for each token varies for a Time token (e.g.
@PUNCH_T) you need 5 characters (mm:ss), whereas for a descriptive token
(e.g. @DESCR) you will want to insert several words (30-70 characters). When
designing your template it is a good practice to write down the size you allot
for each token, so that you will know in the future not to attempt to insert too
many characters in its place
5. Save the template as Text Document (.txt) in the Machines folder of cncKad
(to see its location, go to Settings => Machine Settings => Machine tab =>
Machine Settings => Machine Path). If you are working in a plaintext editor
(Notepad etc.) simply save the document to the above mentioned folder; if
you are using WordPad, you will have to specify the Save as Type as "Text
Document", since there are no file type extensions displayed:
6. Go over the template again, checking that each token has at least one space
preceding it and at least one following it.
7. Thats it you are done. Jump to the Testing your Template section.
6.1.3.3
Creating an RTF Template
1. Open Word.
2. Make your template, incorporating the attributes you have chosen; you can
use different colors, font sizes and types, and tables. When drawing tables,
be aware you can only use the plain line type.
3. After each attribute write the corresponding token, making sure you leave at
least one free space before the latter one. After each token you must leave a
certain size of free space, to make a room for the attributes value. If you have
incorporated tables, move their limits to accommodate for it.
4. Because in this format you will probably wish to use tables, it is imperative to
note the following:
The size you must leave for each token varies for a Time token (e.g.
@PUNCH_T) you need five characters (mm:ss), whereas for a descriptive token
(e.g. @DESCR) you will want to insert several words (30-70 characters). When
designing your template it is a good practice to write down the size you allot
for each token, so that you will know in future not to attempt to insert too
many characters in its place.
5. Save your template into the Machines folder of cncKad (to see its location,
go to Settings => Machine Settings => Machine tab => Machine Settings =>
Machine Path), making sure you save it as an RTF file.
6. Open the template with WordPad, and save it again. This removes all the
extraneous coding Word inserted into it. Close the document.
7. Open the template in a plaintext editor.
145
cncKad
8. Go over the document, and make sure that every token is followed by a
space. You cannot do this in WordPad, as the RTF format contains a lot of
hidden code that only appears in plaintext.
9. Save the document. You dont have to worry about formats it will be saved
as an RTF.
6.1.3.4
Creating a DOC Template
Before beginning:
o Always start from one of the Templates supplied with cncKad, and use
the tables included in it (if you need tables).
o Do not attempt to create new tables for Parts or Tools in the supplied
tables there is an underlying code, which you would need for report to
work.
1. Open Word.
2. Open an existing Template and use Save As option to create a new
template (observing the Naming Conventions).
3. Make the changes and additions you want, incorporating the Attributes you
have chosen; you can use different colors, font sizes and types, and tables.
4. Save your Template in the Machines folder of cncKad (to see its location, go
to Settings => Machine Settings => Machine tab => Machine Settings =>
Machine Path).
6.1.4
Testing your Template
Open cncKad and go to Settings => Machine Settings => NC Report Template tab.
In the File Name field, click the dropdown menu and choose your new template
(assuming you have used the naming convention explained above).
Open a previously created part, and run the Post Processor by holding down the Ctrl
button in the Common Toolbar. After the post process is
key and clicking the
over, go to File => Print Preview, and choose the Doc Report File option in the
Select Print Mode dialog.
A new window will open showing a Report File that was produced using your
template. Go over it carefully, making sure all the values are in their proper places;
this is especially important for RTF templates.
Common problems:
1. In a Text/RTF/DOC template, attributes value isnt shown in the report.
Resolution reopen the template in a plaintext editor and place a space
before the token.
2. In a Text/RTF/DOC template, an attributes token is shown instead of its
value.
Resolution reopen the template in a plaintext editor and place a space
after the token.
3. In an RTF/DOC template, an attribute has "jumped" a cell in a table.
Resolution check that you have allotted the correct free space for the
attribute preceding the one that jumped.
4. In a plaintext template, all the lines and text are out of place.
Resolution cncKads plaintext templates are read in DOS, so you must
correct your template with DOS Edit; to do this, go to Settings => Machine
Settings => Machine tab => Machine Settings. In the Selected Machines
window choose your machine and then find your template in the Edit
146
Punching Manual
Machine Files dropdown menu; click Edit button and your template will open
in DOS Edit. Correct all the offsets and save the template.
6.1.5
Tokens in cncKad
Here you will find lists of cncKad tokens that can be used for creating template:
6.1.5.1
Common Tokens
Following is a list of the most common tokens:

Token
ANGLE
Attribute
CLAMPS
The position of the clamps
CLEARANCE
Tool Clearance values: Min, Best, Max
CLMP_QTY
Number of clamps
CUST
The name of the parts customer
CUT_T
Time taken up by cutting (Laser)
CUT_TP
Cutting time per Part: to be used in a Nesting Line (Laser)
The tools angle (Punch)
Gives the cutting time only if the part has a SubRoutine

CUT_WAY
The length of the cutting path (Laser)
DATE
Date
DATE_T
Date with Time
DESCR
The parts description
DRAWNUM
The drafts serial number
FILE
The NC files name and partial path
LENGTH
The tools length (Punch)
MATERIAL
The parts material
MODEL
The machines model
MOVE_LEN
The rapid movement path (Laser)
MOVE_T
The rapid movement time
NESTING
This token denotes if this is a nesting
NOTE1
The order number of the part
NOTE2
The draft's version
NOTE3
General notes
NUM_OF_SHEETS
Number of Sheets
P_PREV
Part's preview
PART_DIM
The parts dimensions
PART_NUM
The total number of parts
PIERC_NUM
The number of pierces (Laser)
PIERC_T
The piercing time (Laser)
PROC_T
Total time for the processing
PROGLNG
The program's length
PROGNUM
The programs serial number
147
cncKad
PROGR
The programmers name
PUNCH_T
The time taken up by punching (Punch)
QTY
The number of parts in a Nest
REPOSNUM
The number of repositions
ROTTUR
Sheet's rotation/turn
SHEETD
The sheets dimensions
STAT
The tools station number (Punch)
STROKES
The number of hits per tool (Punch)
THK
The sheets thickness
TC_T
The time taken up by tool changes (Punch)
TL_DIE
Dies for the Tool
TOOL_NUM
The total number of tools used (Punch)
TYPES
The tools type (Punch)
WIDTH
The tools width (Punch)
PB_NAME
Part's file name, without the extension
PB_DX
Size of Part in X
PB_DY
Size of Part in Y
PB_AREA
Part Area: when the Nest is generated by Auto Nest, this is

an exact area, otherwise area of bounding rectangle
PRT_WGHT
Part Weight in Kg, e.g.: 2.120 kg When the Nest is

generated by Auto Nest, this is an exact Weight, otherwise
Weight of bounding rectangle
PB_WU
According to current Units, e.g.: For mm: 2.120 kg For

Inch: 4.664 lbs
PB_WKG
Kg without units string: 2.120
PB_NUM
Part Running Number
SHT_WGHT
Sheet Weight in Kg: 52.50 kg
SHT_WU
According to current Units, e.g.: For mm: 52.50 kg For Inch:

115.50 lbs
SHT_WKG
Kg without units string, e.g.: 52.50
START_CORNER
Program Origin, with the following values: 0 - Top-Left Origin

1 - Bottom-Left Origin 2 - Bottom-Right Origin 3 - Top-Right
Origin
X_START_CORNER
The Starting Corner X value
Y_START_CORNER
The Starting Corner Y value
Decimal Digits:
If you want to use in an RTF Report Template,

ALWAYS use as follows:
@#S1 =
At start of Report, after an Empty line!
@SET_FIXED_DECIMAL_DIGITS{ 3 }
@#S1 =
At End of Report
@SET_FIXED_DECIMAL_DIGITS{ -1 }
SET_FIXED_DECIMAL_DIGITS{ 3 }
148
Generate 3 decimal digits, e.g.: 35.000
Punching Manual
SET_FIXED_DECIMAL_DIGITS{ -1 }
6.1.5.2
Return to original decimal settings, e.g.: 35.
Additional Tokens
Below you can see the list of additional tokens:

Token
ACC
Acceleration in X in mm / sec
ACCX
Acceleration in X in mm / sec (the same as ACC token)
ACCY
Acceleration in Y in mm / sec
AR_SHT_THCK
Sheet directives for ARIESII directives
AR_TBLOCK
Tool blocks for old ARIES 245 directives
ARII_METAL
Material Type for ARIESII
ARIIPROGR
Programmer name (for ARIESII)
AR2STAT_NUM
Tool blocks for Nisshinbo directives
NI_TBLOCK
Tool blocks for ARIES 245-II and ARIES 255 directives
CALL_NCSEC
Call to NCSEC from model (MDL)
CL1
First clamp
CL2
Second clamp
CL3
Third clamp
CL4
Fourth clamp
CL1F
Clamp 1-st position on X with floating point
CL2F
Clamp 2-nd position on X with floating point
CL3F
Clamp 3-rd position on X with floating point
CL4F
Clamp 4-th position on X with floating point
CL1N
Hopper number of the 1-st clamp
CL2N
Hopper number of the 2-nd clamp
CL3N
Hopper number of the 3-rd clamp
CL4N
Hopper number of the 4-th clamp
CLAMPS_MOVED
The value will be equal 1 if ANY clamp has been moved
CLAMPS_CHECK
The value will be equal 1 if the clamps position should be

checked
CL_ARII
Clamps position (for ARIESII)
SHT_EFF
Sheet efficiency (in percentage)
CUPS
Cups value for FinnPower when loading sheet
CUT_PRESS
Cutting pressure
DBLSLASH
Generate double slash '//'
DELAYEDPUNCH
Notifies when the punch is delayed
DFT_PATH
Path of DFT file
DFT_XOFS
DFT offset on X
DFT_YOFS
DFT offset on Y
F_HEADPOS
Focus the position of cutting head
F_PRE_PRG
Pre Program Functions
Attribute
149
cncKad
F_POST_PRG
Post Program Functions
FNAME
File name (without extensions)
FNAME_WITH_
Like @FNAME with replacing all Non-Alphanumeric signs

into '_'
FEED_MAX
The maximum machine feed
FEED_X_MAX
The maximum machine feed on X
FEED_Y_MAX
The maximum machine feed on Y
FIRST_X
First punch position on X
FIRST_Y
First punch position on Y
FTL_BDC
Bottom Dead Center for Forming tools
FTL_TDC
Top Dead Center for Forming tools
GAP
Gap
GAS
The character of the gas
GLOB_COOLING_TIME
Cooling time from Global Cut
GLOB_CUT_SENSOR
Final cutting sensor
GLOB_PIERCE_SENSOR
Final piercing sensor
LAS
Gives information about laser (from Material Technology

Table)
GEOM
Gives information about geometry (from Material

Technology Table)
ENGRAVE_QTY
Quantity of engraved elements
PIERCE_TYPE_QNT
Number of types of piercing
LCURLY
Generate '{' left brackets
STATION_IN_SETUP
Station in setup; the value will be 1, if the specific tool is also

in same station in the current setup
IS_STATION_LOCKED
The value will be 1 if the specific tool is locked in the station
LENS_NUMB
Number of cutting lenses
THIS_LINE_NUM
Number of current line
LINE_NUM_STEP
Step of the line numbering
LOADING_MODE
Loading mode: 0=Manual, 1=Auto
UNLOADING_MODE
Unloading mode: 0=Manual, 1=Auto
MATNUMBER
Material's number
MAT_TONNAGE
Tonnage of material
DENSITY
Density of material
CLR_MIN
Minimal clearance
CLR_BEST
Best clearance
CLR_MAX
Maximal clearance
MATMNAME
Machine's name (Material parameters)
MATCLASS
Material class: 0=Steel, 1=Stainless 2=Aluminium
MAT_MAX_WIDTH
Material Max Width for Dynamic Pierce
MAT_MACH_NAME2
Machine's Name 2
150
Punching Manual
MAT_ID
Material ID
MACHOFSX
Machine offset on X
MACHOFSY
Machine offset on Y
MTG
Material Gage
MEASURE_SHEET
Measure sheet: 0=do NOT measure, 1=Measure
MEASURE_SHEET_TYPE
Type of Sheet Measuring
MEASURE_CORNER1_X
Measure 1-st Corner on X
MEASURE_CORNER1_Y
Measure 1-st Corner on Y
EDGE1_LENGTH_X
First Edge Length on X
EDGE1_LENGTH_Y
First Edge Length on Y
MEASURE_CORNER2_X
Measure 2-nd Corner on X
MEASURE_CORNER2_Y
Measure 2-nd Corner on Y
EDGE2_LENGTH_X
Second Edge Length on X
EDGE2_LENGTH_Y
Second Edge Length on Y
MEASURE_HOLE1_X
Measure 1-st Hole on X
MEASURE_HOLE1_Y
Measure 1-st Hole on Y
MEASURE_HOLE1_DIA
Measure diameter of the 1-st Hole
MEASURE_HOLE2_X
Measure 2-nd Hole on X
MEASURE_HOLE2_Y
Measure 2-nd Hole on Y
MEASURE_HOLE2_DIA
Measure diameter of the 2-nd Hole
MM_TO_UNITS
Convert millimeters to inches. For example:

@MM_TO_UNITS{ 254 } will generate 254 for mm, and 10 for
Inch
TURRET
Turret name
NCEXT
NC extension only
NCPATH
Partial NC path
NESTING
Nesting
NOTEARII
Note for ARIESII
NPART
The name of the part
NUM_ON_X
Number of parts on X
NUM_ON_Y
Number of parts on Y
PART_PATH
Partial path without extension
PB_N
Current Part Number (in Multiple Parts)
PB_PRC_NUM
Part: quantity of piercing
PB_AREA_NO_UNITS
Part: area without units
PB_SUM_PART_AREA
Total parts area
PB_WGHT_NU
Part: weight without units
PB_SUM_PART_WEIGHT
Total parts weight
ALL_VAC_FIELDS1
Notice all vacuum fields being used in the first arm of Part
Unloader
ALL_VAC_FIELDS2
Notice all vacuum fields being used in the second arm of
151
cncKad
Part Unloader
AREA_UN
Area units
WEIGHT_UN
Weight units
MAT_THK_ID
Material thickness ID
CUT_WP
Cutting way of current part
PB_WORK_ORDER
Part's working order
PAU_STOP_PUN
The punch can be stopped from NCSEC or from Function
The punch can be pushed out on center from NCSEC or

PAU_PUSHOUT_CENTER_PUN from Function
PAU_PUSHOUT_RIGHT_PUN
The punch can be pushed out on right from NCSEC or from

Function
PAU_PUSHOUT_LEFT_PUN
The punch can be pushed out on left from NCSEC or from

Function
The punch can be pushed out, without movement, from

PAU_PUSHOUT_NOMOVE_PUN NCSEC or from Function
PAU_PUSHOUT_FIXED_PUN
The punch can be set as fixed from NCSEC or from

Function
PAU_STOP_CUT
The cut can be stopped from NCSEC or from Function
The cut can be pushed out on center from NCSEC or from

PAU_PUSHOUT_CENTER_CUT Function
PAU_PUSHOUT_RIGHT_CUT
The cut can be pushed out on right from NCSEC or from

Function
PAU_PUSHOUT_LEFT_CUT
The cut can be pushed out on left from NCSEC or from

Function
The cut can be pushed out, without movement, from NCSEC

PAU_PUSHOUT_NOMOVE_CUT or from Function
PAU_PUSHOUT_FIXED_CUT
The cut can be set as fixed from NCSEC or from Function
PATH_NAME_EXT
Partial path, name and extension (DFT or NST)
PIN_NUM
Pin number
PRE_PROG_FUNC_1
Pre Program Functions 1
PRE_PROG_FUNC_2
Pre Program Functions 2
QTY_OF_SUBS
Quantity of Sub-Routines in current NC
QTY_OF_STATIONS
Total number of Stations in the Turret
QTY_TOOLS
Real number of used tools; equals the number of used

stations.
Example:
RO 6.2
RE 50 5
RE 50.001 5
RE 50 5
Seq=99
QTY_TOOLS = 2 TOOL_NUM = 4
QTY_FORMING_TOOLS
Number of the forming tools
NAME_FORMING_TOOLS
Name of the forming tool
152
Punching Manual
QTY_TAPPING_TOOLS
Number of tapping tools
QTY_MAX_TAPPING_TOOLS
Maximum Number of tapping tools allowed
QTY_LAS_TOOLS
Number of active laser stations
RAINER_TOOLS
Generates tools for Rainer machine (in the beginning of the

NC)
REL_PATH
Partial (Relative) Path with NC extension
REPOSLAST
Last Reposition in X
REPOSTOTALPREVTRANS
Total value of reposition of previous Transformation
REPOSTOTALCUR
The Total value of reposition up to this point
REPOSFIRST
First reposition in X
REPOS2
Second reposition in X
REPOS3
Third reposition in X
REPOS4
Fourth reposition in X
REPOS5
Fifth reposition in X
TRANSTYPE1
First transformation type
TRANSTYPE2
Second transformation type
TRANSNAME1
First transformation name
TRANSNAME2
Second transformation name
END_OFFS_DX
Sheet End Offset in DX
END_OFFS_DY
Sheet End Offset in DY
SET_DECIMAL_MODE
Set Decimal Mode: 0- Always, 1- Never, 2- Only if needed
SET_FIELD_SIZE
Set Field Size
SET_FIXED_FIELDS
Set Fixed Fields

Set the current interpolation. For example: @SET_G0123{0}
to set G00, or to force interpolation on next command:
SET_G0123
@SET_G0123{ -1 }
SET_LINE_NUMBERING
Set line numbering: 0- OFF, 1- ON

For example: @SET_LINE_NUMBERING{0} means: do NOT
put line numbers
SET_PUNCH_MODE
Set Punch Mode: 0- OFF, 1- ON
SET_STATION
Set the current station. If you want to force Tool Change,

@SET_STATION{ -1 }
use -1:
Set the Head in X. For example: @SET_X_HEAD{130}
SET_X_HEAD
or: @SET_X_HEAD{@#F1}
SET_Y_HEAD
Set the Head in Y
SET_X_MACH_OFS
Set machine offset on X
SET_Y_MACH_OFS
Set machine offset on Y
SFEVAL
Make some calculation; the result is a decimal number,

according to the current MDL precision and number format.
For example: @SIEVAL{ @SHTY / 2 }
SHEAR_IS_USED
Notices if the Shear function is being used or not
SHEETDIM
The dimensions of the sheet
SHEETGAP
Sheet Gap
153
cncKad
SHT_TYPE
Sheet Type: 0=Normal, 1=Formed, 2=Irregular
UsedArea
The area of the bounding rectangle of the parts on the sheet
SHT_SIZE_ID
Sheet size ID
SHT_XOFS
Sheet offset on X
SHT_YOFS
Sheet offset on Y
SHTX
Sheet size in X
SHTY
Sheet size in Y
Make some calculation, the result is Integer. For example:
SIEVAL
@SIEVAL{ @THK * 10 }
SHEXEVAL
Convert the decimal value to hexadecimal value
SIZE_AND_DX
Part size and distance between parts on X
SIZE_AND_DY
Part size and distance between parts on Y
ST_ABC
Station Size Letter
ST_ABC_NUM
Station Size letter, then Station Number. E.g.: B 314
STATION_NUM
Number of the station
STATION_AI
Auto Index Station: 1 for AI Station, 0 for Standard Station
STATION_MULTY
Notifies if there is a Multi Tool Station
ST_OFFSET_X
Station offset on X
ST_OFFSET_Y
Station offset on Y
SUBS_DEFS
Code for creating subroutine definitions in the NC program
SUBS_CALLS
Code for creating subroutine calls in the NC program
TC600ID
ID for Tools: a special TC600 feature
TAP_NUM
Number of Tapping tool
TAP_NUM_ROT
Number of rotations of Tapping tool
TAP_ROT_SPEED
Speed of rotations of Tapping tool
SEC_TO_TIME
Converting seconds to time: For example: 6005 => 100:05
TIME_TO_SEC
Converting time to seconds: For example: 100:05 => 6005
THK2
Thickness displayed with two decimal digits
US_THK
Thickness displayed with one decimal digit
TL_CHANGE_POS
Change tool position
TOOL_LINE
The line of the tool (in NC)
TOOL_N
The number of the tool
TOOL_FNAME
Brings name of Special (F) tool. E.g.: BANANA.T ->"BANANA"
TRAVEL_GAP
Travel gap
TRAVEL_GAP_HOLES
Travel gap in cutting of the holes
TRAVEL_GAP_PARTS
Travel gap in cutting of the parts
END_GAP
End of the gap
TSEQ
Tool Sequence number
TTLSTRK
Total number of strokes with tools
TL_TYPES
Tool types defined by two letters
TOOL_CODE
Tool Code. Codes are as follows:
154
Punching Manual
1 - RO (ROUND)
2 - RE (RECTANGULAR)
-2 - SQ (SQUARE)
3 - OB (OBROUND)
5 - SD (SINGLE D)
6 - DD (DOUBLE D)
9 - F (TOOL FILE)
10 - CR (CORNER RADIUS)
12 - RR (ROUND RECTANGLE)
20 - B (BEAM - Laser, Plasma, Water, Flame, etc)
The shape type of the tool; the shapes parameters are as

follows:
TOOL_TYPE
TOOL_SHAPE_NONE=0,
TOOL_SHAPE_CIRCLE=1,
TOOL_SHAPE_RECT=2, OVAL=3, POLY=4, D=5,
L=6, GRID=7, MULTIH=8, FILE=9, X=10, Q=11,
ROUND_RECTANGLE=12, DRILL=13, MILL=14, MJ = 15,
BEAM=20, SHEAR=30, SQUARE=-2, ROUND_SQUARE=-12,
TRIANGLE = 16
TL_CMNT
The comment about the tool
TL_DIE
Tool Dies
TL_F
String of ALL the Tool Functions
TL_FIS
String of one Tool functions
TL_FIN
Number of one Tool functions

Wilson Wheel Tool ID:
TL_WID
1 Shear
F WW01 (Wilson Rolling Shear)
2 Rib or RollBall (for Euromac) F WW02 (Wilson Rolling Rib)
3 Offset
F WW03 (Wilson Rolling Offset )
4 Louver F WW04 (Wilson Rolling Louver )
5 Pincher or Grooving MK (for Euromac) F WW05 (Wilson
Rolling Pincher)
100 Beading Trumpf F BEAD01.T
200 Marking, RB for Euromac
F MARK01.T
TL_S
Number of hits per this tool
TL_H
Tool height
TL_AREA
Tool area
TL_1
First tool size length
TL_2
Second tool size width; for CR Cutting width
TL_3
Third tool size; for CR and RR Radius size
X_HEAD
Current Head Position (in Sheet Coordinate X)
Y_HEAD
Current Head Position (in Sheet Coordinate Y)
Z_HEAD
Current Head Position (in Sheet Coordinate Z)
X_HEAD_OFS
Current Head Position (in Machine Offset Coordinate X)
Y_HEAD_OFS
Current Head Position (in Machine Offset Coordinate Y)
XLOADPOS
Loading position on X
XPIN
Pin position on X
XRANGE
Machine range on X
YRANGE
Machine range on Y
155
cncKad
X_PROG_ORIGIN
Program origin in axis X
Y_PROG_ORIGIN
Program origin in axis Y
UNLOAD_X_DIM
Unload in dimension X
UNLOAD_Y_DIM
Unload in dimension Y
UNLOAD_X_COR
Unload in corner X
T_DIA
Diameter of the tube
T_WIDTH
Width of the tube
T_HEIGHT
Height of the tube
T_COR_RAD
Tube Corner Radius
T_TYPE
Tube profile type
T_PROFILE
Tube profile string
T_PROC_LEN
Tube processed length
T_SUP1
Tube Support Place 1
T_SUP2
T_SUP3
T_SUP4
T_SUP5
T_CLAMP_TECH
Tube clamping technique
T_PROC_TYPE
Tube processing type
T_WORK_POS
Working Position of the tube
T_SUP_LOAD_POS
Support loading position: 1= right side; -1= left side
T_SUP_DEAD_MINUS_X
Support Dead Zone Minus X
T_SUP_DEAD_PLUS_X
Support Dead Zone Plus Y
T_STAND_OFF1
Tube Nozzle Stand Off Step1
T_STAND_OFF2
Tube Nozzle Stand Off Step2
T_RED_CUT1
Reduce tube's cutting speed Step 1
T_RED_CUT2
Reduce tube's cutting speed Step 2
EMPTY
Create empty line in NC code
T_SUP_TYPE
Tube's support type
M_NUM_TEETH
Number of teeth in Milling
M_FEED_PER_TOOTH
Feed per tooth
M_CUT_SPEED
Cutting speed for Milling
M_T_TYPE
Milling tool type
UD_DATA1
Drawing Number (in User Data)
UD_DATA2
Project/Customer name (in User Data)
UD_DATA3
Programmer's name (in User Data)
UD_DATA4
Description (in User Data)
UD_DATA5
Order Number (in User Data)
UD_DATA6
Revision/Version number (in User Data)
UD_DATA7
Note (in User Data)
156
Punching Manual
UD_TITLE1
User defined title for @UD_DATA1
UD_TITLE2
UD_TITLE3
UD_TITLE4
UD_TITLE5
UD_TITLE6
UD_TITLE7
CUR_GAS
Gas used for cutting current sheet
CUR_HEAD
Head used for processing current sheet
CUR_LENS
Lens used for cutting current sheet
GC_ENG_PRICE
Engineering rate
GC_PROG_PRICE
Programming rate
GC_MACH_HOUR_RATE
Hourly machining rate
GC_MACH_SETUP_RATE
Machine setup rate
GC_MACH_SETUP_TIME
Total machine setup time
GC_GRINDING_RATE
Hourly Grinding Rate
GC_PRICE_PER_BEND
Hourly rate per Bend
GC_TIME_PER_BEND
Bending time
GC_BEND_SETUP_RATE
Bend Setup Rate
GC_PRICE_PER_TAP
Hourly rate per Tap
GC_TIME_PER_TAP
Tapping time
GC_PRICE_PER_DRILL
Hourly rate per Drill
GC_TIME_PER_DRILL
Drilling time
C_PUNCH_SPEED
Punching speed
C_NIBBLE_SPEED
Nibbling speed
C_PUNCH_TIME
Total punching time
C_ENG_TIME
Total engineering time
C_PROG_TIME
Total programming time
C_MAT_TYPE
Material Type (in Estimation)
C_THICKNESS
Material Thickness (in Estimation)
C_MACH
Machine type name
C_GAS
Used gas type
C_HEAD
Used cutting head type
C_LENS
Used cutting lens size
C_CUT_SPEED
Machine's cutting speed
C_GRIND_TIME
Total Grinding Time
C_BEND_SETUP_TIME
Total Bend Setup Time
C_MAT_COST
Material price
C_NUM_PUNCHES
Quantity of Punches (in Estimation)
C_PIERCE_QTY
Total number of pierces
157
cncKad
C_BOX_X
Sheet size in X (in Estimation)
C_BOX_Y
Part's bounding rectangle size in Y (in Estimation)
C_EFF
Sheet's efficiency in percentage
C_AREA_GR
Part's area gross (in Estimation)
C_AREA_NET
Part's area net (in Estimation)
C_WEIGHT_GR
Part's weight gross (in Estimation)
C_WEIGHT_NET
Part's weight net (in Estimation)
C_VAP_LEN
Vaporization path length
C_ENGRAVE_LEN
Engraving path length
C_CUT_LEN
Total cutting length
C_TRAVEL_LEN
Machine travel path length
C_CUT_TIME
Total cutting time
C_ENGRAVE_TIME
Total engraving time
C_VAP_TIME
Total vaporization time
C_PIERCE_TIME
Total piercing time
C_TRAVEL_TIME
Total machine travel time
C_GRIND_PRICE
Total Grinding Price
C_MAT_PRICE
Material Price (in Estimation)
C_DRILL_QNT
Quantity of Drills
C_TAP_QNT
Quantity of Taps
C_BEND_QNT
Quantity of Bends
C_DRILL_TIME
Total Drilling Time
C_TAP_TIME
Total Tapping Time
C_BEND_TIME
Total Bending Time
C_DRILL_PRICE
Total Drilling Price
C_TAP_PRICE
Total Tapping Price
C_BEND_SETUP_PRICE
Total Bend Setup Price
C_BEND_PRICE
Total Bending Price
C_CUT_MACH_TIME
Total processing time
C_TOTAL_MACH_TIME
Total machining time
C_ENG_COST
Total engineering cost
C_PROG_COST
Total programming cost
C_SETUP_COST
Total setup cost
C_MACH_COST
Total machine use cost
C_TOOL_QTY
Total number of used tools
C_TOOL_CHANGE_TIME
Tool change time (in Estimation)
C_TOT_COST_1
Total cost for one part with material
C_TOT_COST_NO_MAT_1
Total cost for one part without material
C_TOT_COST_10
Total cost for ten parts with material
C_TOT_COST_NO_MAT_10
Total cost for ten parts without material
158
Punching Manual
C_TOT_COST_100
Total cost for hundred parts with material
C_TOT_COST_NO_MAT_100
Total cost for hundred parts without material
Total cost for thousand parts with material

C_TOT_COST_NO_MAT_1000 Total cost for thousand parts without material
C_TOT_COST_1000
C_TOT_COST_VAR
Total cost for desired amount of parts with material
C_TOT_COST_NO_MAT_VAR
Total cost for desired amount of parts without material
C_TOT_COST_VAR_AMOUNT
Any number of parts you wish to get the pricing for
6.1.6
ToolBlockOrder Model Key

The following section is for advanced users only.
One of the Keys in a machines MDL file is ToolBlockOrder. This Key sets the
ordering of the Tools:
Value
NC ordered by
Report file ordered by
0
1
2
3
NC order
NC order
TURRET order
TURRET order
NC order
TURRET order
NC order
TURRET order
NC order means: the order in which the tools work.

Turret order means: order by Stations this is easier for doing the setup on
the machine. Also, tools which are changed several times during the NC
(when the tool is used with different Tool Sequence), will appear only once.
By default, this Key is set to "0".
6.1.7
Key Words for Tool List in NC and in Report

Supported in V6.3x.
You can put in the Report Template (and also in the HDR file) the following Key
Words:
@TL_F
@TL_CMNT
Tool Functions
Tool Comment
This is useful for VIPROS machines for the special M-codes, and in other cases also
where special M-codes, delays, feeds etc. are being used.
For example, in the HDR file:
Old HDR:
@TBLOCK_BEGIN
(*T@STATION_NUM @TOOL_LINE)
@TBLOCK_END
Change to:
@TBLOCK_BEGIN
(*T@STATION_NUM @TOOL_LINE @TL_F)
@TBLOCK_END
159
cncKad
Or in the Report Template:
|ST No.| Type |Length | Width|Angle |
M
|Hits
|
|@STAT |@TYPES |@LENGTH|@WIDTH|@ANGLE | @TL_F | @TL_S |
For example:
...
(*SHEET 1000.0 1000.0 1.0)
(MAT St 37-2 SPC 1.0)
(*T202 RO 5)
(*T303 SQ 7 45)
(*T210 RE 28 3 AI)
(*T214 F LUVER.T M536 , M13 PRESS MODE CANCEL)
(*T201 RE 65 5)
(*T218 RE 70 3 90 MEDIUM SPEED)
(*T307 F EMBOSS16.T M549, M13 PRESS MODE CANCEL)
G92X1210.00 Y1270.00
G90
...
Another issue is the order of the tools (see the ToolBlockOrder Model Key section).
Here you can see the same tool list as above, arranged by Turret order:
(*T201 RE 65 5)
(*T202 RO 5)
(*T303 SQ 7 45)
(*T307 F EMBOSS16.T M549, M13 PRESS MODE CANCEL)
(*T210 RE 28 3 AI)
(*T214 F LUVER.T M536 , M13 PRESS MODE CANCEL)
6.1.8
Template Examples
The following examples illustrate the differences between the types of templates, and
present what can be done with each type.
6.1.8.1
A plaintext template example
The lines and words do not line up in this example; they will when cncKad, or you,
will open the template in a text editor.
160
Punching Manual
6.1.8.2
An RTF example
161
cncKad
6.1.8.3
6.2
A DOC Example
Creating New Functions
As explained previously in this manual, cncKad contains a list of pre-prepared

functions that you can assign to a tool, punch or program.
If, however, you find that you are in need of a special function that does not appear in
the list, you can create a new function to suit your requirements.
6.2.1
The Function's Structure
Each Function is comprised of three parts:

ID number this number is always preceded by /N .
There cannot be two functions with the same ID number.
6.2.2
Name this is will be the Functions identification in cncKad.

Code the actions to perform when this Function is called.
Making the Function available for cncKad
The Functions are defined in the machines MDL file; the name of this file varies
according to the machine, but it is always named according to the following pattern:
machine_name.MDL (in this example the machine is a Vipros 367 Queen, and so the
file is called VIPR367Q.MDL).
To access this file, go to the Settings => Machine Settings => Machine tab =>
Machine Settings dialog and mark the machine you are using, and from the
dropdown menu shown below choose machines .MDL file and click Edit button.
162
Punching Manual
The Editor will open the file and you will be able to write there a new function, using
the following format:
/N 221 NAME: "Lubrication ON"
M212
G04 X0.5
In the above example, 221 is the identification number, Lubrication ON is the name,
and the two other lines are the actions to perform.
6.2.3
Adding the New Function in the Code
In this example we will insert the new function before every punch made with an SQ
10 tool.
In the Used Tools dialog, mark the Turret Station holding the SQ10 tool:
Click Tool Functions button and the following dialog will open:
163
cncKad
Define when you want this function to be used, and click OK button.
You will be able to see the results of this insertion after you create the NC code the
lines of code written in the MDL file now precede each punch made with the SQ 10
tool:
164
Punching Manual
6.3
Tool Clearance
The following section is for Punch and Combination Machines only.
The Tool Clearance refers to the clearance between tool and die, with respect of the
material.
To access the Clearance settings, go to the Material tab in the Workspace Settings
dialog and click the Edit Material button. The following window will open:
As you can see, for each material you can define a Minimum, Best and Maximum
values as percentages of sheet thickness.
165
cncKad
The values for each material were taken from the Amada charts, but you
can modify them to comply with the recommendations for your specific
machine.
The values for the Clearance are indicated in the Report File, with the @CLEARANCE
token.
6.4
Repositioning principles
Depending on your machine, the table size and the sheet size, your machine will
have to reposition the clamps when working on a sheet that is longer than the table.
Another reason to reposition is if you want to place punches in the clamps Dead
Zones.
Normally, the Post Processor generates Reposition and Head Position
(during the Reposition) commands automatically, however you can add
manual repositions from the Reposition and Transformation option of
the CAM menu.
6.4.1
Clamp Avoidance
cncKad permits the user to place parts that are going to be processed in the area of,
or even beneath, the clamps. This option allows manufacturers that produce grids of
holes on a complete sheet, or nest multiple parts on a single sheet, to maximize
sheet utilization by punching in the areas around and beneath the clamps, areas that
are otherwise not accessible.
This option is activated automatically, as soon as the user positions a CAM in the
area of the clamps. During the creation of the NC program, the post processor will
calculate the reposition data, tool size and Dead Zone data and create a program
that institutes repositioning as is needed, so as not to damage the clamps.
The number of repositions in a program is determined by several factors:
The table size
The sheet size
The size of the Dead Zone
If the sheet selected is less than, or equal to, the table size there will only be one or
two repositions. If the sheet selected is larger than the table there will be two or
more repositions, as needed.
When a tool was selected (for punching), its Dead Zone is represented on the
graphic creation screen as a blue rectangle surrounding the clamps.
While the program does most of the work and calculations for the repositioning, there
are still some points that the user must take into consideration when using this
option. Understanding and utilizing these points is crucial to the success of the
automatic clamp avoidance algorithm, executed by the post processor.
For all machines the basic rules are much the same:
The sheet is punched at the origin of the sheet and in the area where the
clamps will be after the first reposition. Having executed a reposition, the
program will punch the area where the clamps were before the reposition and
will continue until the next reposition or to the end of the sheet.
The position of a clamp is determined by the distance of its center from the
left edge of the sheet.
The general Dead Zone is determined according to the largest Dead Zone of
the used tools.
166
Punching Manual
6.4.2
The minimum sheet size for a machine with two clamps is 3.5 times the Dead
Zone, and for three clamps 5.5 times the Dead Zone.
Initially, the Post Processor will try to use the clamp positions set by the user,
but if unsuccessful, the positions will be changed automatically.
Repositioning Example Tables
Setting the distances between the clamps is crucial, therefore we will give a few
examples of machines with two clamps and with three clamps:
6.4.3
Automatic Repositioning for Small Sheets
As mentioned above, the minimum sheet size for utilizing the automatic Clamp
Avoidance (for a machine with two clamps) is 3.5 times the Dead Zone.
For sheets smaller than this, a different strategy is needed. The initial position for
both clamps is on the right side of the sheet and the left side is processed, and then
both clamps are moved to the left and then the right side is processed.
This strategy is possible under these restrictions:
The combined Dead Zones will cover less than half the sheet (otherwise there
will be an overlap of Dead Zones after the repositioning).
The maximum repositioning movement will be less than the distance from the
sheets right edge to the edge of the Table.
The following example illustrates these principles:
Table size 1250
Dead Zone 200
Sheet size 600
167
cncKad
(Automatic Clamp Avoidance not possible: 200x3.5 = 700)
Proposed solution:
Positioning
Clamp 1
Clamp 2
Area processed
Initial
400
540
0 - 300
After reposition
60
200
300 - 600
The reposition in this case will be negative: -340mm.

It is important to note that the initial position of the clamps is at the users discretion
they can be placed close together, with a resulting small reposition but loss of sheet
stability, or they can be far apart (under the above mentioned restrictions), with a
large reposition but a more stable sheet.
6.5
Laser Processing Long Parts
The problem of processing long parts comes up when a contour in the part includes a
Line entity with an X length larger than the machines Working Range:
The solution is in two stages:

Use the Split command, from Edit toolbar, to break up the long Line entities
into segments smaller than the Working Range.
In order to make the procedure easier, first place a Help Line where you want to
create the Splits; the simplest way is to set Snap=Center for the Help Line, and then
return to Snap=Auto for the Splits:
168
Process the parts contour as two Chains, where the Chains begin and end at
the Splits:
Punching Manual
It is imperative to be precise about the clicking positions when creating the chains:
After you go through this procedure, cncKad will be able to insert repositions as
necessary during the Post Processing.
This procedure is necessary for all Lines longer than the Working Range.
6.6
Wilson Wheel Programming in cncKad
The following topics explain how to use Wilson Wheel tools with cncKad.
6.6.1
Tools
The standard tool library supplied with cncKad contains the following Wilson Wheel
tools:
WW01.T - Wilson Rolling Shear
WW02.T - Wilson Rolling Rib
WW03.T - Wilson Rolling Offset
WW04.T - Wilson Rolling Louver
WW05.T - Wilson Rolling Pincher
For use with Fanuc controls they are named this way:
WW01
WW02
WW03 and so on.
For use with Siemens and Nisshnibo, they look this way:
169
cncKad
WW11
WW12
WW13 and so on.
Below you can see an example of Rounded Rectangle processing (200mm x
100mm, R=50mm) with WW12:
6.6.2
Programming
=+Nibble Entity, Nibble Chain or Nibble Contour.

Make sure Index=ON (to enable Rotation of the Wheel).
If you want to work on a "smooth" contour (no sharp corners), for example, Round
Rectangle, you can use the
[ x ] Connect
so the Wheel stays down from cut to cut.
170
Punching Manual
Wheel cutting Speed and Depth can be set for the tool and for individual cuts (if, for
example, you want to reduce the speed at arcs compared with lines). When adding
the Wheel in Add Punch dialog, mark the Use Tool Data checkbox and there, on the
Type Properties tab you will be able to enter Speed and Depth values.
Checking the Use Tool Data box is a shortcut to Tool Data option of Tool
Library dialog.
Plunge-In:
For machines that support Plunge-In, select a line in the contour to be processed and
split, for example into two halves. Start a cut on one half and finish it on the other.
Using Edit CAM option, click the half you started cutting from, change to Offset and
set a Plunge-In distance of, for example 10mm.
6.6.3
Common Cuts
When you wish to have Common Cuts for Wheel Tools, simply set the distance
between Parts (dx or dy or both) to 0.01.
Then, while running the Post-Processor (NC), make sure that in the last screen
(Post-Processor Options) the automatic testing of common cuts is checked.
[ x ] Automatic testing of common-cuts
6.6.4
Customization
Customization for the default values is done in the MDL file.

However, anytime you use a Wheel on your part, you can set the parameters to suit
the specific cut. For more information on this issue go to Type Properties section of
Tools Menu chapter of this manual.
6.6.4.1
Customization using Functions
Function
Function
Function
Function
Function
101 used to start WW01

171
cncKad
Function 99 used to End all the Wheel Tools

Function 100 Wheel Connect (keep cutting/forming, do NOT lift-up
Head)
6.6.4.2
6.6.5
Customization using NCSEC
[NCSEC_WW_Start] to start any WW tool (Functions 101 -105 will NOT be

used)
[NCSEC_WW_End] to end any WW tool (Function 99 will NOT be used)
[NCSEC_WW_Down] lower the Head to start cutting/forming
[NCSEC_WW_Up] lift-up the Head to Stop cutting/forming
Cutting/Forming Speed
In the NCSEC or Function for the Wheel Start, normally some Feed command is
placed, e.g.
F4000
This will be the default speed of the Tool.
Normally, the machine operator will adjust it on the machine (see also the Use Tool
Data option).
6.6.6
The Wilson Wheel Section in the MDL file.
[Wilson]
BaseFuncWilsonStart = 100
// function 100 is: Continue Wilson (NO
RAM up)
;
// function 101 is Wilson Rolling Shear Start
Commands.
;
// They are inserted as Tool-Change function
automatically.
;
// 102 is Rolling Rib Start
Commands,
;
// 103 is Offset,
;
// 104 Louver
;
// 105 Pincher
ControlSupportG02G03 = Yes
// can we use G02 and G03 or we
have to use
;
// Nibble commands
ShedMaterialTravel = 10
// When working with WW01 (Rolling Shear
= Cutting),
;
// whenever finishing a cut and Lifting Up
the Head, a
;
// 10mm travel is done to "Shake away" the
Sheet
;
// from the Wheel.
172
Punching Manual
6.7
Using Sheet Transformation
6.7.1
Processing with a Sheet Transformation
Often the sheet in use extends beyond the machines Working Range. When this
happens in the X range, the solution is to use a Reposition, however when the sheet
extends over the Y range, the solution is using a Transformation.
The problem:
Processing a 2000mm x 1100mm part on an Amada Aries245 (Working Range
1000x1270):
Note above the arrows marking the sheets extension beyond machine's Working
Range.
The solution:
o
o
Click the Reposition and Transformation button Use the Add button to add a 180 rotation:
In the Transformations section of the dialog select the Rotation 180

entry, and then click the Set CAMs to Current button, to select the parts
you want to process when the sheet is in this position. For that sake you
can use any of the standard Selection Methods (Single, Window, etc.).
o Now you have two Transformations; note that when you click on either of
them, the CAMs that are defined for it will be highlighted.
After you generate the NC, you will see that there is a Stop Machine (M00) inserted
in order to allow rotating the sheet before the machining continues.
o
You can also use Sheet Rotation when there is a problem with the
clamps Dead Zones and the sheet is too small for using a Reposition
first process away from the clamps, rotate the sheet and process the
rest.
173
cncKad
6.7.2
Sheet Transformation with Reposition
Sheet Transformation can be used in conjunction with Reposition in the following

way:
The problem:
Processing a 2000mm x 1200mm sheet on an Amada Pega344 (Working Range
1000x1000).
6.8
The solution:
o Process the bottom 600mm, using Repositions for Clamp Avoidance
and in order to reach the X=2000 position.
o Insert a Rotation 180 type Transformation, and process the remainder
of the sheet.
The NC to DFT feature
This section explains the steps needed to turn a given NC file into a DFT file.
6.8.1
Preparing the GCD file
To use the NC to DFT option, some changes must be made to the header of the NC
several comment lines with information must be added.
For example, the original GCD file contained the following lines:
(AD1-OS)
G92X1830.00Y1270.00
G90
U1
X24.5Y120.T230
V1
G73X763.Y563.Q3W1
G73Q4W1
G73Q2W1
U2
X92.Y62.T150
V2
G73Q3W2
G73Q4W2
G73Q2W2
U3
G72X46.Y46.
G66I50.J270.P-30.Q-80.T237
V3
G73Q3W3
G73Q4W3
G73Q2W3
G50
To use this option, the following lines (marked with the asterisk) have to be added:
(AD1-OS)
(*MODEL PEGA357 58I)
(*SHEET 750.0 550.0 1.0)
174
Punching Manual
(*CLAMPS 290.0 440.0)
(*T230 RO 10)
(*T150 RO 20)
(*T237 RE 80 30)
G92X1830.00Y1270.00
G90
U1
X24.5Y120.T230
V1
G73X763.Y563.Q3W1
G73Q4W1
G73Q2W1
U2
X92.Y62.T150
V2
G73Q3W2
G73Q4W2
G73Q2W2
U3
G72X46.Y46.
G66I50.J270.P-30.Q-80.T237
V3
G73Q3W3
G73Q4W3
G73Q2W3
G50
In this case, the comment lines are added after the first line, the one with the Part
Name. They contain information about the Sheet size, Clamps position, and Tools.
If the customer uses a Standard Setup, then a Setup file can be created as explained
later on.
These new comment lines can be stored in a file, for example in HDR.PNC .
In such a case, the steps to prepare the GCD file are as follow:
1. Open Metalix Editor.
2. Open HDR.PNC
3. Mark all the lines and select Edit => Copy (or Ctrl+C)
4. Open the GCD file.
5. Place the cursor at the start of the second line (following the Part Name)
6. Select Edit => Paste (or Ctrl+V)
7. Correct Sheet Size, Clamps, and Tools if needed.
8. Use File => Save As with the same name, but with extension .PNC
6.8.2
Loading the prepared NC file
Open any part in cncKad, click NC icon in order to generate an NC File, and then go
to the Simulation program. There select File => Open, and load the .PNC file you
prepared just before.
You will be able to see the Part on the Graphic Simulation screen, Run it slowly or
Line by Line (Line=ON). It is also possible to make manual corrections to the NC
file, and see and verify them immediately in the Graphic Simulation window.
175
cncKad
After making changes to any line, remember to press Enter key in order to
confirm the change.
6.8.3
Creating a drawing (DFT)
After finishing the steps described above, you can select File => NC to DFT option in
the Simulation program. This will generate a Drawing with the CAMs already in
place!
Now you can close the Simulation, return to the main cncKad screen, and use File
=> Open Part to load the newly created DFT file.
Note that the generated DFT will normally NOT have a valid geometry,
therefore it is recommended that you correct it manually.
6.8.4
Creating a Setup file
In cncKad go to Tools => Turret Setups and create your standard Setup File, for
example:
PEGA357.PET
For more information on Setup file including the procedure of creating a new Setup
and editing an existing one, see the appropriate sections of Tools Menu chapter of
this manual.
In order to use a Setup file, you must add the following lines (marked with asterisk) in
your HDR.PNC file:
(*SHEET 750.0 550.0 1.0)
(*CLAMPS 290.0 440.0)
(*SETUP PEGA357.PET)
You must also remove the T lines (the lines that specify Tools).
If for Part processing the Tools are being used ONLY from the Setup, then adding
these 4 lines is all you need to do. However if tools for Part processing are being
used both from the Setup, AND a few tools NOT from the Setup ("Non-Standard
Tools"), you should add the T lines only for the "Non-Standard Tools".
For example, the following tools are being used to process the Part:
RO 6.5
RO 4
SQ 12.7
OB 32 8 90
RE 50 5
RE 50 5 90
And from among them, only the OB is "Non-Standard Tool". So in this case your NC
header will look this way:
(*SHEET 750.0 550.0 1.0)
(*CLAMPS 290.0 440.0)
(*SETUP PEGA357.PET)
(*T303 OB 32 8 90)
176
Punching Manual
6.9
Laser Common Cuts
The Laser Common Cut feature is being used to process the edges of two adjoining
parts with the same cut; instead of cutting each part individually, the following
procedure is implemented:
o When a part is being processed, cncKad checks if any juncture on the
parts contour is also the starting point for a future cut one for cutting
the contour of an adjoining part.
o When cncKad prepares to cut this adjoining part, it begins from the
Preparatory Cut (using an Overlap, to create a smooth transition), made in
the direction of the future cut, thus avoiding the need to pierce the sheet
again.
The advantages of using this method are:
Reduced machining time.
Savings in cutting \gas and wearing of parts.
Reduced material wastage.
Using Laser Common Cuts is recommended in the following cases:
Parts with long, straight contours.
Parts cut from thick sheets, where the cutting speed is low.
Parts with contours that will be vaporized, as these require two passes,
resulting in a double reduction of machining time and gas.
6.9.1
Preparing a Geometry for Common Cut
In order to use Laser Common Cut on geometry, it is compulsory to prepare

geometry particularly for it, first; there are two options of doing this:
Array a part (using the Part Array option from Transform menu) with the dX
and dY distances set at Beam diameter (see the Example below).
Load parts into a Nest in Auto Nest, set the Buffer size at half the Beam
diameter (e.g. for a Beam with a 0.2 diameter use a 0.1 Buffer), and then
send the entire Nest to cncKad as a DFT file.
6.9.2
Preparatory Cut
In the Auto Cut dialog, on Auto Cut tab mark the Perform checkbox and click the
Settings button, like shown below. The Common Cut Parameters dialog will open:
From this dialog you can set the parameters governing this option:
Preparatory (Cut Length) in order to minimize the need of piercing, the
Post Processor will create a Preparatory Cut in the positions where a new
cut will start.
The example below shows how the bottom-left part will be cut:
177
cncKad
Notice the enlarged sections when arriving at the middle juncture, the cutting is
extended upwards and to the right, to prepare for cutting the bottom-right and topright parts. The same action is being taken at the bottom juncture.
Overlap this is the distance from the end of the Preparatory Cut, to where
the actual cutting will start when processing will resume on the adjoining
parts.
6.9.3
Example
This feature can only be used on complete geometries, where the distance between
parts has been set to the Beam Diameter.
In this example we will make an Array of the following part:
To array the part we will use the Part Array option from Transform menu. After
choosing it, click the contour of the part; the entire part will be highlighted in blue
color. Press Enter key in order to confirm the selection. As soon as you do so, the
178
Punching Manual
Fill out the parameters definitions as shown above; note that in the Distance Between
Parts section, dX and dY are both set to 0.2, which is the Beam diameter value.
Click the OK button, and the part will be arrayed on the sheet according to the above
definitions:
Now it is time to process the sheet; click the Auto Cut button. When the following
dialog will open, select the Auto Cut tab:
179
cncKad
In this tab, select the Perform checkbox in the Common Cut section, and click the
Settings button. After doing so, the Common Cut Parameters dialog will open. Enter
the settings you desire, and click OK button.
Now go to the Laser Optimization tab and set the path Between Parts as either
Snake X or Snake Y:
When you have finished, click the Run button. The entire sheet will be processed,
including the inner contours of the arrayed part. If you don't want to process the inner
contours, you should check the Only contours to be selected option on the Auto
Cut tab.
180
Punching Manual
Use the Ctrl+B key shortcut (or View => Full Cut Tool Width) for switching the
Beams width on and off, to make sure the cuts are processing the arrayed part
correctly.
In order to view the effect of using the Common Cut function on the actual
processing, we will use the cncKads Simulation program. To do that generate NC
for the part, and then go to the Simulation window.
Run the Simulation, and Pause after the contours of the first part have been
processed. Zoom onto the intersections with the adjoining parts, and note the
Preparatory Cuts.
6.10 Additional Options in cncKad's Machine files

6.10.1
Additions in the MDL file
These changes have been introduced from cncKad version 6.41:
6.10.1.1
New MDL Keys
NCUnitsMode = ? with values as follow:

o 0 Use DFT units
o 1 Always generate mm
o 2 Always generate Inch
MPCornerMode = ? with values as follow:
o 0 Q1 is at bottom-left, and Dy is positive
o 1 Q1 is at top-left, and Dy is negative
AssignStationsMode = ? with values as follow:
o 0 Allow smaller tools into bigger stations
o 1 Each tool size MUST fit the Station Size
[SendToDiskette]
o CreateFolderIfNeeded = No
// if Yes, the Target Folder will be
created, if does not exist.
o AskForConfirmation = No
// if Yes, user is asked to confirm
copying
o CopyNCReportToo = No
// if Yes, the NC Report file (if exists)
is copied to the same destination as NC.
6.10.1.2
Functions have moved to MDL files
Functions Names are now specified in the MDL, and each MDL file contains only
those functions that belong to specific machine:
...
N 0 BEGIN
/N 1 NAME: "0.5 SEC DELAY"
G04 X0.5
G04 X1.
G04 X2.
G04 X5.
/N 5 NAME: "LOW SPEED"
F4
181
cncKad
/N 6
F3
/N 7
F2
/N 8
F1
/N 9
M01
...
6.10.1.3
NAME: "MEDIUM SPEED"

NAME: "HIGH SPEED"
NAME: "MAXIMUM SPEED"
NAME: "OPTIONAL STOP"
Functions can be used as Pre-Macro or Post-Macro
/N 1082 #S! NAME: "M82 Macro Only"

M82
/N 1083 #S! NAME: "M83 Macro Only"
M83
If "M82 Macro Only" is used as Pre-Tool, and "M83 Macro Only" is used as Post-Tool
and for example, U3-V3 is the Macro for that Tool, you will get:
M82
U2
.
V2
G76 W2 Q1
M83
6.10.1.4
Delete comments from NC
Some machines do not accept the comments that appear between brackets in the
NC code. In the MDL file, you can set the deletion of these comments as they are
sent to a diskette.
All the following fields can be copied from the Example Model File (Examp.mdl)
situated in the Machines folder, if they are not already existent in the MDL file:
In your machines MDL file, go to the section [SendToDiskette]
and add New Key =
Enter: Remove Comments = Yes
CopySrc2Trg = Yes
You can define the Target Extension as you wish, for example: trgext = nc
If the NC code is modified in the Simulation screen, that change will be
automatically updated to the .nc file.
6.10.2
Run Out in cncKad
A Run Out means that the Turret never passes over a Clamp. This result is achieved
in the following way:
When the Turret approaches a Clamp, the Sheet moves away in Y, bypasses the
Clamp in X and then comes back in Y:
182
Punching Manual
To define a Run Out you must edit the machines MDL file, in the section called
General Info.
There are 3 key values to consider:
[General Info]
RunOutRequired = No
YExtraForRunOut = 0
MinYForRunOut = 0
RunOutRequired choose Yes or No to use a Run Out option.

YExtraForRunOut when using the Run Out option, this value (in mm) will
be added to the Dead Zone as defined in the Turret file.
MinYForRunOu this defines the minimum value (in mm) for the Run Out,
even when the Dead Zone + YExtraForRunOut are less than this value.
If you are using Inches as your System Units, you must still define the
values in mm; these will be automatically converted by cncKad.
For Example for the following definitions:
[General Info]
RunOutRequired = Yes
YExtraForRunOut = 40
MinYForRunOut = 200
The result will be that a Run Out will always be used, with a value of 200mm (~ 7.9")
or Dead Zone + 40 (~ 1.6"), whichever is greater.
6.10.3
Support for very big arcs
When the NC codes for generating Arcs contain Angles, we can have an accuracy
problem when the Arc Radius is very big.
This happens in all FANUC controlled machines (Amada, Murata, FinnPower, LVD,
and more) and in some other controls as well.
The accuracy problem is now resolved automatically by adding the following Keys
into the MDL file:
[NC_GENERATION]
ArcNCByAngles=Yes
// supported from V8.0: correct NC
for very big Arcs
AnglePrecision= 0.01
6.10.4
Additions in the TRT files
For Round Only stations, it is now possible to set:

0 Any Shape
183
cncKad
1 Only Rounds
90 Used for an Auto Index station; allows rotating the index station only at
90 degrees
For more information on these features see the Edit Turret section on Tool Menu
chapter of this manual.
6.10.5
Support for Program Origin
To enable/disable support for Program Origin, do the following:

Set the following two Keys in the machine MDL files [Machine
Info]section:
SetOriginEnable = ? with values as follow:
o 0 disable,
o 1 enable, but default is false,
o 2 enable
InitialOffset = ? with values as follow for the initial point:
o 0 Top-Left Origin, i.e. (0, Sheet Y size)
o 1 Bottom-Left Origin, i.e. (0, 0)
o 2 Bottom-Right Origin, i.e. (Sheet X size, 0)
o 3 Top-Right Origin, i.e. (Sheet X size, Sheet Y size)
The program uses for the latter mentioned Key:
Incremental programming used to set the Initial Head Position.
Absolute programming used to set the Machine Offset.
In the DIR_xxx.HDR file change the SHEET directive as follows:

(*SHEET @SHTX @SHTY @THK @MATNUMBER @START_CORNER
@X_START_CORNER @Y_START_CORNER)
cncKad will change its coordinates according to new program origin.
6.10.6
MDLX per machine file
Some of the functions defined in the MDL file have been moved to a file with MDLX
extension this file is also per machine, and it includes all the machine parameters
that are editable via cncKad.
6.11 Inches users upgrading from previous versions to 7.xx

The following information is intended for cncKad users who are upgrading
to version 7.xx from a previous one.
For customers who are using more than one System Units set (mm / Inch): you
must make sure that the following values are correct:
6.11.1
Values that are per Working Unit
These parameters are defined for each Working Unit, and in order for cncKad to
function properly, they must be set separately for each one of them in the Settings
=> Workspace Settings => Working Defaults tab:
Decimal Digits
Bulge
Tolerance
Angle Tolerance
184
Punching Manual
You only must set these values once for Working Unit; thereafter the
values are saved by cncKad.
6.11.2
Values translated when switching between Working Units
Each time you switch from one Working Unit to another, some values are being
"translated" multiplied or divided by the mm-to-inch ratio. Therefore every time you
make the switch, you should go over these values to make sure they have been
translated correctly:
In the Settings => Workspace Settings dialog:
o Material tab Default Material => Sheet Thickness.
o Display tab Text Size and Arrow Size.
In the Settings => Machine Settings dialog:
o Cutting Parameters tab (for Laser machine users):
~ Tool Offsets defaults Start and End.
~ Entry Length.
~ Exit Length.
o Auto tab Auto Processing => Min Part Size.
o Machine tab Sheet and Part parameters.
In the Auto Punch dialog (for Punch machine users):
o In the Auto Punch Parameters tab
~ Tool spacing defaults Minimum tool overlap and Scallop for round
tools.
~ Cutting tools restrictions Minimum and Maximum Widths.
~ Notches Minimum and Maximum Offsets .
o In the Holes tab:
~ Crunch Holes up to Width and Length.
~ Wire Joint Width and Place Every.
Common Cut Parameters (for Laser machine users) Auto Cut => Auto Cut
tab => Common Cut section => Settings button => Preparatory and
Overlap parameters.
6.12 cncKad V.8s new Material List

This section is meant for laser cutting machines. It describes how to start working
with the New Material List, being used in version 8.0 and higher ones:
This section is intended only for those users, who have upgraded to version
8 (and higher) from previous versions.
6.12.1 Introduction
Beginning with version 8.0, cncKad will be using a new format for its Material List
where in previous versions there were 15, 20, or even more materials, now there will
usually be 5-10.
185
cncKad
This is because in the past, the list contained the same materials, but with different
Gas, Head or Lens definitions. e.g.:
In this example the same material is defined twice once for cutting with Oxygen,
and once with Nitrogen. In the new list, for each Material the Gas, Head and Lens
definitions can be selected separately; this means a shorter list, but much more
flexibility.
In order to use the new list you will need to create a Conversion Table, that will
allow cncKad to select the correct material from the new list, when you will open a
part created in a previous version (and therefore having an old material defined for
it).
The conversion process, described on the successive pages, is done when you open
cncKad for the first time, after installing the new version. But can still change the
conversion settings at any time. For more information on how to do this go to
Changing the Conversion Definitions section of this chapter.
The scheme of converting materials looks this way:
When you open cncKad, after the installation completes, a window will open giving
you the option to convert your old list to the new format:
We highly recommend going through with the conversion process. If you are
dissatisfied with the results, you can always return to using the old list at any time.
If you are not interested in converting your old list, check the Dont show
this message again option and click the Cancel button.
To start the conversion, click the Take me to the materials conversion wizard
button. The following message will appear:
186
Punching Manual
Click OK and the Conversion Wizard will open.

The conversion consists of two stages:
Choosing the Materials List for the new list.

Converting materials using the Materials Conversion Table.
6.12.2
Laser Technology Material List
When the Conversion Wizard opens for the first time, the first dialog you will see is
the Laser Technology Material List. Each material shown in this list has its own laser
technology table.
If this list is not extensive enough for your use, simply add other materials.
In order to move to the next step, click Next button.
6.12.3
Material Lists
Now you will see two Material Lists: a long one, containing the materials used in your
previous version of cncKad:
187
cncKad
and a new, short one, consisting of just five default materials:
The user chooses which of the lists he wants to be used as a New Material List. In
order to confirm your choice and move on to the Materials Conversion stage, click
Next button.
If this list is not extensive enough for your use, you can simply add other materials.
6.12.3.1 Adding Materials to Lists

The instructions given in this section apply for adding materials both to Laser
Technology Material List as well as to Material Lists.
Click the Add Material button. The following dialog will appear:
Enter the new materials name and select the base Material Type for it:
188
Punching Manual
This Material Type will be used to set the initial attributes for the new material
Tonnage, Density, Clearance, etc., so you should select the Type, that resembles the
new material the most.
For example, when adding Copper to the list, you will probably select Aluminum as
the base Type:
As a result, Copper will be added to the list with Aluminums attributes:

In Laser Technology Material List:
In Material List:
You can now change the attributes, so that they reflect Coppers true nature click
inside a table cell and enter the correct value.
Click Next to continue.
6.12.4
Materials Conversion Table
This table tells cncKad how to treat materials from the old list. This means that when
you open an old file, it stands to reason it will have an old material defined for it; this
table tells cncKad which new Material, Gas, Head and Lens to select for it instead.
189
cncKad
6.12.4.1
Selecting a New Material for the Old one
To start material conversion, mark the Use New Materials List checkbox at the top
of the dialog. Now, for each Old Material, select a New Material from the dropdown
list:
If you anyways want your new material list to look like the old one, don't
check the Use New Materials List option. The materials will be
automatically copied from one column to another.
After selecting a New Material, you can also change the definitions for Gas, Head
and Lens, like shown below:
Selecting a Gas:
Selecting a Head:
Selecting a Lens:
After defining a new materials for all the old ones (you cannot continue unless all
materials are defined), click the Finish button to create the Conversion Table.
6.12.4.2
Use for conversion
When you enable this option, cncKad reads the Laser Technology Material List and
looks for which material there are no assignments. When it finds such, then
automatically it marks it with "V". The selected material will replace the standard
cutting definitions with the ones from the Old Material List.
190
Punching Manual
For example, the first time you select Stainless as the New Material this option will be
checked automatically, if the new material does not have cutting data in the laser
technology cutting table, but it will not be checked for subsequent selections of
Stainless (or if there is already an entry for it within the table).
This is an useful feature for experienced users who have calibrated their old laser
cutting tables and know the specific parameters needed for them.
This option will be used only if the Convert old laser table for selected
materials checkbox is selected.
6.12.4.3
Convert old laser table for selected materials
When this checkbox is selected next to some materials, cncKad knows that it should
take all the data from the old (pre-existing) version with all the cutting parameters and
copy it to the new table. When this checkbox is unselected the cncKad will use the
defaults supplied with the software system.
This will be done only for those materials, where the Use for conversion
option is selected.
6.12.4.4
Using the new list
After the conversion is complete, cncKad will open and you from now on you will be
able to use the new material list. Go to Sheet tab of Set Sheet and Clamps dialog
and see the dropdown Material List:
See the picture shown below.

In the Technology Parameters section you will see other material definitions like
Gas, Head and Lens and from dropdown lists will be able to choose various options
for them, if it will be possible.
In the Technology Table section you will see the laser technology parameters for
your settings or material type and sheet thickness. Notice that in our example data
displayed here differs from the settings entered in above Sheet Thickness field. This
is because in the Laser Technology Table there is no such thickness for this material
type. So it offers you the closest value existing in the table for this material.
191
cncKad
Now, when you'll go to the Laser Technology Table you will see that thickness
presented here is the same as in Technology Table section of Sheet tab, presented
above. However in the bottom part of the dialog you will see the actual Sheet
Parameters displayed in blue color.
6.12.5
Changing the Conversion Definitions
You can change the conversion settings at any time, by going to the Settings =>
Workspace Settings => Material tab and clicking the Convert Materials button.
This will re-open the Conversion Wizard, and you will be able to re-define the
conversions.
192
Punching Manual
You can also use this to return to using the old List, but there really is no point of
doing this if you take the time to do the Conversion correctly, you will get your old
data integrated into the new list.
This action is not recommended.

To return to using the old materials List:
1. Open the Wizard as mentioned above
2. Click the Next button
3. Unselect the Use New Materials List checkbox and click the Finish button.
In this Material tab you can also Edit Materials as well as Edit Laser Technology
Materials, by clicking on the appropriate buttons. When you do, you will be directed
correspondingly to and to Material List or to Laser Technology Material List. You can
add new materials here, as well as edit their parameters, if applicable.
6.13 The cncKad Service Pack

The cncKad Service Pack is an application that updates cncKad installations
(seats) with the latest versions of program files. These updated versions may include
new features, fixes for bugs, etc.
6.13.1
Installing the cncKad Service Pack
To use the Service Pack for updating cncKad you need to do two things:
Place the Service Pack application on a local/network drive.
Set cncKad to use this application for updating.
For the first of these, we recommend saving the application to a dedicated directory
on the PC or on the server, as shown in the examples presented below.
After saving the Service Pack to this directory, do the following:
Open cncKad, go to Settings => Workspace Settings and select the Live Update
tab:
Mark the Check for Updates checkbox, and then click the
button for browsing
to the Service Packs directory:
If this directory is on local PC, searching it might look this way:
193
cncKad
If the directory is on a network drive, then the browsing may give the following result
(depending on the drive letter):
Regardless the Service Packs directory location, its path will be shown in the
Downloads' Directory field:
After making sure that the path is correct, do not forget to click the OK button, to
confirm activating the Update feature.
Thereafter, each time cncKad is opened, it will check for updates and install them
when appropriate.
6.13.2
Working with networked seats
When there are several cncKad seats working together on a network, we

recommend saving a single copy of the Service Pack on a network drive, and then
following the procedure described above for each of the seats.
There is no need for each seat to save an individual copy of the Service Pack they
all can use the same one! This will ensure that all the seats are updated to the same
version, and will also protect against cross-version compatibility issues.
If there is a Firewall protecting the network, it must be set to allow the
cncKad seats to access the Service Packs directory.
6.14 The cncKad Update Manager

This section gives explanations about cncKads Update Manager.
6.14.1
What is the Update Manager
The cncKad Update Manager is an application that allows your workstation to keep
up with the most recent updates released for cncKad. This is done by downloading
updates from the cncKad website and installing them to the local workstation(s).
Likewise it was for Service Pack installation, here there are also two basic
configurations for working with the Update Manager:
Local this configuration is straightforward a single workstation runs the
Update Manager and applies the updates.
194
Punching Manual
Network this configuration is more complex one workstation runs the

Update Manager, but the updates are downloaded from the website to a
network directory, and cncKad gets the update from this directory for each
workstation connected on a network.
The diagram below explains this process:
6.14.2
Installing the Update Manager
After starting the cncKad Update Manager installation you will get the following
window:
195
cncKad
Here you will see the default installation directory. If you want to install Update
Manager elsewhere, click the Change button and choose a different location.
You must install Update Manager on a computer that has an internet
connection.
Click the Next button, and you will be presented with the following window:
Select the Yes, I want to launch Update Manager2006 now checkbox, click the
Finish button and the Update Manager will open.
6.14.3
Configuring the Update Manager
These are the three stages to configuring your Update Manager:
Selecting a download path
Entering a Customer ID
Setting the update check interval
6.14.3.1
Selecting a download path
When the Update Manager opens for the first time, you will be asked to select a
location for storing the updates after downloading them:
196
Punching Manual
At this point you must decide if this is a local or network configuration (as explained
above):
Local select a local directory, e.g. C:\cncKad\SP
Network select a network directory.
For this example we will choose a network configuration, and select the folder
F:\cncKad\Update Manager:
It is compulsory that this directory can be accessed from all the computers
connected to the network; otherwise they will NOT receive the updates!
Click the OK button and the directory path will be shown on the display, as marked
on the picture below. You can change this path at any time from this dialog.
197
cncKad
After confirming the path, a new window will open, asking if we want to check for
updates now:
At this point choose No, because in order to download updates you must have valid
Customer ID for your Update Manager.
6.14.3.2
Entering a Customer ID
If you try getting updates without first entering a Customer ID, you will receive the
following message:
In order to enter your Customer ID, click the Settings button, and when the dialog
shown below will appear, type-in the ID number and click OK.
6.14.3.3
Setting the update check interval
In the main window you can set the interval for checking if there are updates:
There are several options for this interval:
198
Punching Manual
Automatic checks you can specify the frequency of checking for updates
from one of two options weekly or daily:
When choosing this option, in the top of the dialog you will see when the Last
Update Check was done and when the next one is scheduled for.
Manual checks in this case a check for updates will be performed only
when you click the Check for updates now button.
6.14.4
Configuring the cncKad workstation

The following configuration must be done for every workstation.
In cncKad, go to the Settings => Workspace Settings => Live Update tab.
To receive updates, do the following:
Select the Check for Updates option.
Browse to the directory in which the program will be looking for updates; this
will be the directory selected as the destination for downloading the updates
(in our example this is: F:\cncKad\Update Manager):
The next time when you open cncKad, the Update Manager will check for the
updates and if it finds any, the following message will appear:
When you click OK button, the updates will be automatically installed on your
computer, and cncKad will open.
6.15 Configuring your system to send Problem Report

In order to send Problem Reports, your Windows system must have email capability
and be configured to send emails.
The email capability issue depends on the specific conditions at your workstation
(e.g. whether the PC is networked, if it is behind a firewall, etc.). If you are not sure,
consult your System Administrator.
To configure your Windows system in order to send Problem Reports files, do the
following:
199
cncKad
6.15.1
Open the Control Panel
The procedure to open the Control Panel varies, depending on the Windows version
you are using.
For Win98\ME:
Go to Start => Settings =>Control Panel
For Win2000:
Go to Start => Settings =>Control Panel
For WinXP:
Go to Start => Control Panel (or Start => Settings =>Control Panel
depending on which type of View you have chosen for the Start menu)
6.15.2
Open the Internet Options dialog
From the Control Panel, select the Internet Options icon:
You can also open the Internet Explorer and select this option from the Tools
menu:
6.15.3
Select a default application
In the Internet Options dialog, go to the Programs tab:
200
Punching Manual
Use the E-mail dropdown menu to select the program you would like to handle your
outgoing email massages:
Dont forget to click the OK button to confirm your selection.

More information on Sending Problem Report you will find in the Help Menu
section of Introduction chapter of Drafting and Nesting Manual.
6.16 Multiple Parts with Reposition

The Problem:
When working with Multiple Parts on a sheet bigger then the working range, as
illustrated on the example below, you encounter the following problem:
201
cncKad
There are 8 columns of parts on the sheet. Suppose you will process the first 3
columns, make a reposition, and then process the remaining 5 columns.
While processing the last 5 columns, the first 3 columns are on MicroJoints so
they can easily get disconnected.
The Solution:
Lay out the sheet the normal way, including Common Cuts. Alter the DFT file into
nest, using the command Convert to Nest from File menu. As a result you will get a
NST file laid out identically to your Multiparts on DFT.
Now from Nest menu choose the command Split Array. Click the cursor anywhere
on the array. The parts in the nest will be highlighted with red color, and the following
window will appear:
For our example change the number of columns to 2, set distance between arrays to
30mm and check the option Perform 'Cut Sheet' between arrays. The number of
new columns in new array should be the number of parts overhanging the table
range. Confirm your choice, clicking OK button. You will get the following result:
202
Punching Manual
Go to Used Tools dialog and move the separating tool (the one whose sequence is
99) to the first position in the table. We want it to be the first tool to work AFTER the
Reposition. Confirm your settings with OK button. Next generate NC.
When the simulation module window will open, watch the punching sequence in the
Graphical Simulator:
1. The first two columns are being punched.
2. Reposition is being made.
Pay attention to how the clamps are holding the sheet after repositioning.
The left one should be on the right side of the Cut Sheet.
3. The Sheet is cut off and the machine stopped for the operator to remove the
first two columns.
4. The last six columns are being punched.
6.17 Punching a Perforated Sheet in cncKad

The problem with perforated sheets is that when we try punching them, we often find
that the material distorts, gaining a convex shape. This is dangerous and can cause
a collision with the turret.
The solution is to avoid punching contiguous lines of the perforation, as described
further in this section.
6.17.1
Creating a Perforated Sheet
Generally, you can get a perforated sheet in two ways:

Importing a part into cncKad, e.g. as a DXF file.
If you have imported the part, go directly to the Punching a Perforated Sheet
section.
Creating one in cncKad.
If you want to create a part, continue in this section.
203
cncKad
6.17.1.1
Sheet Dimensions
Start a regular part and give it the outer dimensions of your sheet. In our example the
sheet sizes are: 1000 x 700:
6.17.1.2
Perforating the Sheet
Go to Draw => Shapes => Punched Sheet and define the perforation like shown
below:
After clicking OK button, the sheet (or parts inner contour), will be filled with round
holes. See the example presented below.
If the Hole Diameter definition does not match any of the tools in your
Library, you will be asked to add this tool.
204
Punching Manual
6.17.1.3
Perforated Sheet example
The result is:
6.17.2
Punching a Perforated Sheet
If the perforated sheet was created with the Punched Sheet feature, go directly to
the Optimizing the Path section, since the sheet is already punched.
If our sheet was imported, we will punch it now using Auto Punch feature, and then
we will set a specific Optimization Path for this punching.
6.17.2.1
Using Auto Punch
Open the Auto Punch dialog and go to the Holes tab. There in the Automatic
Detection section, select the Automatically detect lines of single punches option:
Then click the Auto button to punch the part.
6.17.2.2
Optimizing the Path
Open the Used Tools dialog, find the tool you used for the perforation (in our
example: RO 25) and click the Optimize Path cell for this line:
The Tool Data dialog will open on the Optimization Strategy tab.
Select the Tool-specific optimization option, and then proceed to define the
optimization:
Starting Corner use the setting you usually use.
Optimization Path select Snake X.
205
cncKad
Cooling distance this will define the distance between the snakes
curves, or in our case how many rows to jump between passes.
For this example we will use a Cooling Distance of 100:
After clicking OK to confirm these settings, note that the Optimize Path column cell
shows now the Snake X pictogram:
6.17.3
Testing the Optimization
Generate NC and run the Simulation.

You may want to use the Line = On option to follow the optimization path.
We highlighted the specific lines being punched in each curve of the snake:
First pass Lines 1, 7, 13 and 19:
Second pass Lines 2, 8, 14, and 20:
Third pass Lines 3, 9, 15, and 21:
Fourth pass Lines 4, 10, 16, and 22:
206
Punching Manual
Fifth pass Lines 5, 11, 17, and 23:
The last pass takes care of the rest of the lines:
6.18 Installing and Using the NetHASP

The NetHASP enables networked workstations to use a single HASP hard lock key
in a floating license configuration.
We should distinguish between two types of PCs:
The License PC this is the PC where the NetHASP is installed.
Workstations these are the PCs running cncKad.
6.18.1
Installing the NetHASP on the License PC
Plug-in the NetHASP Key to a PC, which will be your License PC.
It is recommended to connect the NetHASP Key on the system server but you can
also connect it on a different PC that does not have cncKad on it; it is compulsory
to make sure that this PC is always on and connected to the network!
The License PC cannot run cncKad.
6.18.1.1
Installing the NetHASP utilities
To install these utilities, insert the cncKad installation CD and click the Net HASP
button.
The utilities that will be installed are:
License Manager (lmsetup.exe):
This application enables other PCs on the network to work with the NetHASP
on the server.
If this application is not running, you wont be able to run cncKad on any
computer.
Aladdins Monitor (aksmon32.exe):
You may run this application if you want to know, which PCs are currently
using the NetHASP.
6.18.2
Using workstations with the NetHASP
If cncKad is already installed, simply disconnect the Metalix Keys (Time Keys or any
other Key), and run cncKad. Otherwise, install cncKad and start working with it.
6.18.2.1
Setting the NetHASP.ini file
For faster operation over the network, it is recommended to set parameters in

nethasp.ini on each workstation running cncKad.
First, you need to know the IP address of the License PC:
To obtain the IP address:
1. Go to the License PC.
2. Click Start => Run and type cmd.
3. In the command line type ipconfig and press Enter.
You should get something like this:
207
cncKad
The second line is the IP address (in the above case 216.70.53.141).
The NetHASP.ini file should be located in the cncKad folder (where the gkadw.exe
file is located), for example:
C:\Metalix\cnckad2006.80
Double-click this file to open it, and modify it as shown below.
The important key is:
[NH_TCPIP]
;;NH_SERVER_ADDR = xx.xx.xx.xx;
First, you must delete the ";;" signs from the beginning of the line.
Next, instead of the xx.xx.xx.xx type the IP address of the License PC,
e.g.:
[NH_TCPIP]
NH_SERVER_ADDR = 216.70.53.141;
Save the file and you are done close the file and open cncKad.
Remember to do this on all the PCs running cncKad!
6.18.3
HASP FAQ
These are the common questions regarding using the NetHASP.
6.18.3.1
What is Error 129?
When you get this message, this means that:

No plug is connected to the PC and License Manager was found.
The PC, where the License Manager is running, is connected to a non
NetHASP plug (like time or memo).
How to solve it:
Replace the non NetHASP key with a NetHASP key on the computer where
the License Manager is running.
Use NetHASP.ini file.
6.18.3.2
Cannot run cncKad with NetHASP connected directly.
If this message appears when running cncKad, then there are two options:
NetHASP is connected to the computer.
HASP driver 5.12 is not installed.
How to solve it:
208
Punching Manual
Use local key (memo/ time) or use NetHASP on a different computer with
License Manager.
Install HASP driver 5.12.
6.18.4 How do I know on which computer the License Manager is

running?
Run Aladdins Monitor it will show you exactly which stations are running a
License Manager.
6.19 Creating a Trimmed Sheet

This section explains how to create a Trimmed Sheet in cncKad.
6.19.1
Why Trim a Sheet
Trimming a sheet is very useful for those cases where the skeletonized sheet may
cause a crash with the turret.
The basic principle is to process the sheet in a way that allows the removal of each
individual part after it has been severed from the sheet. This removal can be done
through a Chute, or manually, but the important issue is that the parts are not left on
the table to rattle around.
For this example we will use the following parameters:
Part Size: 300 x 200
Sheet Size: 2000 x 1000
Cutting Tool: RE 65 5 (in an AutoIndex Station)
Machine Working Range: At least 2000 in X
All sizes are in mm.
6.19.2
Creating the initial part
Create the geometry and punch the holes, using the above mentioned Cutting Tool.
6.19.2.1
First Nibble
Add Nibble Entity with Tool Sequence of 1 to the right vertical side of the part.
Make sure you make this cut with an 3 mm offset on each side.
6.19.2.2
Second Nibble
Add Nibble Entity with a Tool Sequence of 2 to the bottom horizontal side of the
part.
Make sure you make this cut with an 3 mm offset on each side.
6.19.2.3
Current Part View
The results should be as seen on the below picture. Note the offsets of the Cutting
Tool:
209
cncKad
6.19.3
Defining the Sheet
Define the Sheet Size as 2000 x 1000, and set Number of Parts in Y as 1. As you
can see, we now have a single line with 6 parts in it:
6.19.4
Defining the Common Cuts
Now, we will define Common Cuts for these parts click the
parameters as shown below:
The result will be:
210
button and set the
Punching Manual
6.19.5
Using Explode Multiple Part
Now, select the Explode Multiple Part option from the Transform menu:
When you now view the Sheet tab in the Set Sheet and Clamps dialog (click the
button to open this dialog), you will see there is only one part currently on the
sheet:
6.19.6
Deleting extraneous punches
Delete the punching made with RE 65 5 tool, on the vertical right side of the part
number 6 (the most right one) and Redraw the screen, using the
6.19.7
button.
Setting the Trimming
In the Set Sheet and Clamps go to the Trim Sheet tab, check Trim Sheet option, set
the trimming tool to RE 65 5, choose the way you want the sheet to be trimmed and
click OK button:
211
cncKad
6.19.8
Adding Chute commands
We will now set Chute (Push Out) commands; in this example we will open the
chute at part 1, and close it at part 6:
Select CAM => Push Out (Chute):
212
Punching Manual
Set the parameters as shown below and click OK button:
Click on the bottom cut of part 1; it will change to green to signify the Push Out
command:
Press on the Space bar to bring back the Push Out dialog, mark all the open
options, click OK button and click on parts 2,3,4,5 (but not on part 6); the bottom cuts
on all these parts will be colored green:
213
cncKad
Press on the Space bar again, check the Close option, click OK button and then
click on the last part (the 6-th one).
Normally, we will want to use the Chute command, but this can work with a
Stop machine command as well.
6.19.9
Adding more parts to the Sheet
Open the Sheet tab in the Set Sheet and Clamps dialog and set the Number of
Parts in Y to 100; this will ensure that the largest number of parts possible will be
placed on the sheet.
Now we will define Common Cuts for the sheet click the
options as shown below:
button and set the
6.19.10 Setting the tools order

Now, we will set the Cutting Tool (RE 65 5) as the first tool to be used for
processing the sheet; from the Common Toolbar click the Used Tools button
,
and the Used Tools dialog will open, showing a list of the tools that will be used for
processing the sheet.
Click on the Cutting Tool and using the arrows
the list:
move it to the first position in
The tool used to trim the sheet is designated as having a Tool Sequence of
-99.
Congratulation, now you have a Trimmed Sheet:
214
Punching Manual
You may want to go back to Set Sheet and Clamps => Sheet Processing
Technology tab, and select to work in Stripes (Line by Line) for all the tools, or just
for the Cutting Tool.
6.20 Changing Turret Numbering

Each Turret has a default Numbering System that can be changed. In some cases it
comes with a deferent system which is written in the Turret (*.trt) File.
To change the numbering for your turret, in Machine Settings dialog, go to Machine
tab => Machine Settings button. There edit your Master *.trt File and go to:
[TurretInfo]
If this line is not present in your turret file, and you wish to change station numbering,
you should add it.
There are three ways of changing Turret Numbering:
0 This is normal numbering of multi tool station in turret file. That means
that each Multi-tool station is represented by its base number with two or
three digit prelude as indication. With this option it is possible to change Multitool numbering from the Tools Menu => Turret Setups => Edit Turret button.
1 This is a sequential numbering of multi-tool station in turret file. This
means that each Multi-tool station will be given the next number after the
single stations, for example in 20-station turret the first Multi-tool stations will
be numbered as follows: 21,22, 23 and so on. It won't be possible to change
these station numbers manually.
2 Here the number equals base station number (/K) * 100 + station index.
That means that the first number of the Multi-tool station is the number of
base station multiplied by a hundred and added on to the station index. With
this option it is possible to change Multi-tool numbering from the Tools Menu
=> Turret Setups => Edit Turret.
215
cncKad
6.21 Re-Enabling the DOC Report Addin

One of the features of cncKad is creating Job Reports from a Microsoft Word
template.
This feature may get disabled because of various inter-application data exchanges.
If this happens, the next time you try to generate a Job Report you will get this error
message:
In such a case, use the following procedure:

1. Restart your computer.
2. Open Microsoft Word.
3. Go to the Help menu and select the About item:
4. Click the Disabled Items button at the bottom of the dialog:
5. In the Disabled Item dialog, select the docreportaddin item and click the
Enable button:
Do not select other items they are there for a reason!

6. Close all dialogs and exit Word.
Now you can generate Job Reports again.
6.22 Release Notes for BOSCHERT users

In this section you will find explanations and instructions on how to Convert Old
Boschert Tools and adjusting them for work with cncKad.
216
Punching Manual
6.22.1
Boschert Tools
cncKad uses two files for tools:

TOOLLIB.MDB this one contains a list of ALL your tools
LABOD.SET this one contains definitions of BOSCHERT tool numbers
These files can be created manually (using any text editor or the editor that opens
while clicking Edit NC in Files Menu in cncKad), or automatically from BOSCHERT
WZG file in the following way:
1. In your BOSCHERT machine, create a tool file and for NEW control. Now you
will have a TOOLS.BIN file (in old controls it was: ECCO.WZG, TRI.WZG or
PWR.WZG).
2. Place the diskette with the tool file in your PC.
3. From Start => Programs => Metalix, or from your Desktop, run Labod Tool
Convertor.
The program will look for the Machine Tool File on the Diskette. If it won't find it, you
will be asked to locate it manually. When the program will find it, it will select and
automatically ascribe the name of the setup file: LABOD.SET. The Labod Tool
Convertor will create both the LABOD.SET and the TOOL.LIB files.
6.22.1.1
Working with new setup file
Now, in cncKad go to: Tools =>Turret Setups => Add/Create New. You should see
LABOD.SET file in the dialog. Select it by double-clicking on it, or by clicking it once
and then clicking Open button. The LABOD.SET file will appear in the Select Setup
file dropdown list.
When running the Post Processor (by clicking NC button), you will come to the Used
Tools dialog, make sure that in Turret Setups section:
Use Current NC box is checked,
The LABOD.SET file is selected in the dropdown list
This procedure needs to be done just once. Later on, the correct numbers will be
automatically ascribed to the tools.
6.22.1.2
Adding tool to machine
When you add a new tool to the machine station, you have two options:
You can create an updated TOOLS.BIN or WZG file on diskette, and then
run Labod Tool Convertor
In cncKad you can go to Tools =>Turret Setups => Edit Setup button and
add the new tool.
6.22.2
ToolN setting in Tool Library
In the Tool Library Labod Tool Convertor automatically assigns, the ToolN for
every tool, according to the turret station numbers they are in.
This option is designated in order not to use LABOD.SET at all.
6.22.3
Defining Tools' Angle
Tools for Boschert machines should be defined this: RE 25 5 or this way: RE 25 5 90.
You should always start naming the tool with the longer side.
In old controls you could use tool angle ONLY for slanted tools. If you have
a Rectangular tool of 25x5 at 90 degree, define it as RE 5 25 (and not
as RE 25 5 90).
217
cncKad
6.22.4
Setting the Machine Version Parameter
Depending on the version of the machine controller being used the program
created within cncKad will have to be suitable. There are several options of setting
the program version and they can be defined within the MDL file.
To set it correctly, first check the size of the PGM file. Then, go to: Settings =>
Machine Settings => Machine tab => Machine Settings button. In the dialog which
will open highlight your machine, and in Edit Machine Files select the MDL file you
want to edit and click the Edit button.
In the Editor go to:
[Machine Info]
MachineVersion = 11
The 'MachineVersion' parameter could be one of the following:

1: BOSCHERT PGM file, 26128 bytes
6: BOSCHERT PGM file, 34428 bytes (File Version: 7.72)
Versions 10 and upper ones are reserved for New LABOD format (which has no
specific size for the file).
10: New BOSCHERT format (Ver.1), no specific size.
11: New BOSCHERT format (since 1999). Only ONE file is generated.
Subroutine numbers are from 1 to 99.
12: New BOSCHERT format. Each subroutine is in a different file. Main file
has 4 digits (like 1234) and subroutines filenames has 8 digits: first four are
the same as the main file name (1234). The following two are the subroutine
number (from 01 to 99) and the last two digits are 00. i.e. the first subroutine
for 1234 is 12340100.
6.22.5
Offsets for Repeated Functions
If you want the offsets to be the same for ALL the tools, you should make sure that
all tools start processing from the same corner (e.g. Top-Left) and have the same
processing Path (e.g. Snake X).
This can be done in two ways:
By setting the corner and path for Parts, Vertical Cuts and Horizontal Cuts in
Set Sheet and Clamps => Sheet Processing Technology tab.
You can also set these parameters in Settings => Machine Settings =>
Laser Optimization tab. Then they will be the default for every part to
be created.
By setting corner and path for every tool in Tools => Used Tools.
6.22.6
Plasma / Roller / Engrave
cncKad supports Plasma and Roller tools. When using plasma, it can cut the sheet
or just engrave it. The B tool should be used for all these procedures.
For Plasma:
o Plasma tool declaration:
B <beam width>
For example (1 mm plasma):
B1
If you want to engrave using the Plasma use the command Engrave
Entities, then the Set Number for Engrave will be used
218
Punching Manual
For Punch: we still use the B tool, and the Add Cut command:
o "Rollieren" Roller tool declaration:
B <roller width> N = 50
For example (1 mm roller):
B 1 N = 50
o "Gravieren" Engrave tool declaration:
B <roller width> N = 60
For example (1 mm engraving):
B 1 N = 60
Engrave text is also supported - simply use the Engrave Text feature in cncKad.
6.22.7
Converting Plasma.bin to cncKad Laser Tables
More on this feature you will find in Convert Plasma Table to cncKad section of
Settings Menu chapter of Drafting and Nesting Manual (go to: Settings => Machine
Settings => Cutting Parameters tab).
219
cncKad
7 Index
90 Degrees Only ............................121
A DOC Example.............................162
A plaintext template example .........160
Add...................................................42
Add MicroJoint .................................35
Add Punch..........................................2
Add Tool to Library...........................83
Add/Create a New Turret ...............120
Adding Materials to Lists ................188
Adding more parts to the Sheet
Trimmed Sheet ...........................214
Adding the New Function in the
Code ...........................................163
Adding the new tool to the Tool
Library.........................................105
Adding Tool ....................................119
Adding tool to machine...................217
Additional Options in cncKad's
Machine files...............................181
Additional Tokens...........................149
Additions in the MDL file ................181
Additions in the TRT files ...............183
Adjust Travel Path............................81
All Sheet Processing ........................69
All Turret.........................................140
Allowed Angles.................................89
Allowed station sizes........................84
An RTF example ............................161
Appendices ....................................143
Ask
Simulation...................................137
At Hit Boundary ................................37
At Least One ....................................18
At Snap Point ...................................37
At Specific Distance\Angle ...............37
Attribute..........................143, 147, 149
Auto Index ......................................121
Auto Punch.......................................19
Auto Punch Parameters tab .............19
Auto Reposition................................72
Auto Tab...........................................56
Auto Tool Order................................44
Automatic Detection .................24, 127
Automatic Repositioning for
Small Sheets ..............................167
220
Automatic Testing of Common

Cuts ........................................... 126
Beep .............................................. 136
Bend Line K Factor.......................... 64
Best Tools ....................................... 20
Bi Directional ................................... 30
Bin Number ..................................... 44
Boschert Tools .............................. 217
Buffer............................................... 58
CAM Menu ...................................... 31
Cannot run cncKad with
NetHASP connected directly ..... 208
Centered.......................................... 13
CHANGE ....................................... 140
Change Station for New Tool ........ 140
Change Tool.................................... 93
Change Tool for Existing
Punches....................................... 32
Change Turret Tool ....................... 140
Changes Only................................ 141
Changing the Conversion
Definitions .................................. 192
Changing the machine .................... 66
Changing the Sheet Size in X ......... 66
Changing Tool ............................... 119
Changing Turret Numbering.......... 215
Check .............................................. 19
Check Process ................................ 76
Check Stations
Simulation .................................. 139
Choosing a Tool .............................. 11
Choosing Sheets Quantity............... 55
Chute commands
Trimmed Sheet .......................... 212
Chute Type...................................... 43
Circular Tool .................................... 99
Clamp Avoidance .......................... 166
Clamp Button
Simulation .................................. 132
Clamp Coordinates.......................... 66
Clamps Tab ..................................... 65
Close to clamp................................. 84
Close, Do Not Update ................... 141
cmd................................................ 207
cncKad Service Pack .................... 193
Punching Manual
cncKad Update Manager ...............194
cncKad V.8s new Material List ......185
Comment column .............................89
Common...........................................94
Common Cuts ..................................39
Common Cuts Example ...................40
Common Cuts for Grouped
Arrays ...........................................59
Common tab.....................................83
Common Tokens............................147
Configurations to send Problem
Report.........................................199
Configuring the cncKad
workstation .................................199
Configuring the Update Manager ...196
Confirm All Turret Changes,
Correct NC..................................141
Control Panel .................................200
Convert Old Boschert Tools ...........123
Convert old laser table for
selected materials.......................191
Converting Plasma.bin to cncKad
Laser Tables...............................219
Cooling distance...............................94
Perforated Sheet ........................206
Copying Tools from one Library
to another .....................................90
Corner Radius Tool ........................101
Correction for Processed Sheet .......75
Create a Special Tool File................98
Create Setup From Used Tools .......98
Create Tool ......................................86
Create unique IDs for entities...........65
Creating a DOC Template..............146
Creating a drawing (DFT)...............176
Creating a New Setup ....................111
Creating a Perforated Sheet ..........203
Creating a Plaintext Template........144
Creating a Setup file.......................176
Creating an RTF Template.............145
Creating New Functions.................162
Creating the initial part
Trimmed Sheet ...........................209
Creating the LASTSET file .............112
Creating the outline of the tool .......102
Creating the Program.....................124
Creating the Template....................144
Crunch..........................................7, 24
Crunch Arc ...................................... 10

Crunch Chamfer ................................ 9
Crunch Right-Angled Triangle ........... 9
Crunching a notch with one tool ........ 8
Current Part View
Trimmed Sheet .......................... 209
Cursor Coordinates ....................... 132
Customer ID .................................. 198
Customization using Functions ..... 171
Customization using NCSEC ........ 172
Cut Sheet ........................................ 45
Offset ........................................... 46
Tools ............................................ 46
Wire Joint..................................... 47
Cut Sheet Examples........................ 47
Cut Sheet Left Down ....................... 48
Cut Sheet Left Right ........................ 47
Cutting Parameters Tab .................. 60
Cutting Speed.................................. 62
Cutting Table ................................... 81
Cutting Tools Restrictions ............... 20
Cutting/Forming Speed ................. 172
D Shaped Tool .............................. 101
Default application......................... 200
Defining Functions........................... 48
Defining Program Functions............ 50
Defining the Common Cuts
Trimmed Sheet .......................... 210
Defining the Sheet
Trimmed Sheet .......................... 210
Defining Tool Functions................... 49
Defining Tools' Angle..................... 217
Delete a Line ................................. 134
Delete comments from NC ............ 182
Delete Tool ...................................... 96
Deleting a Tool ................................ 90
Deleting extraneous punches
Trimmed Sheet .......................... 211
Deleting Punches ............................ 29
Die Selection ................................... 87
Die Selection in Used Tools ............ 97
Dim Button
Simulation .................................. 131
Direction .......................................... 59
Direction of Stripes Removal........... 70
Directional Punch ............................ 30
Directional Punch option ................. 17
221
cncKad
Display Bend Lines
Simulation...................................138
Display Mode .................................140
Distance Between Parts...................64
Do Not Allow CAM in Clamp
Dead Zone....................................29
Do Not Allow CAM is out of X
working Range..............................29
Do Not Allow No Station for Tool .....29
Do Not Allow Over Tonnage ............28
Do Not Allow Over Travel in Y .........29
Do Not Allow Punch Destroys
Part ...............................................28
Do Not Allow Punch Less than
1.5 Tool.........................................29
Do Not Allow Punch Step Less
than Thickness .............................29
DOC ...............................143, 144, 162
Double D Shaped Tool...................101
Download path ...............................196
Dynamic Piercing .............................61
Edit ...................................................42
Edit CAM Functions .........................49
Edit CAMs ........................................33
Edit Offsets.......................................31
Edit Setup
Simulation...................................139
Edit Titles .........................................68
Edit Tools Library .............................82
Simulation...................................138
Edit Turret ......................................120
Editing an Existing Setup ...............114
Editing the ToolFunc File ...............115
Entities on Sheet ..............................65
Entities Section ................................64
Entity's End ......................................13
Error 129 ........................................208
Every corner.....................................25
Example .........................................141
Execute menu ................................130
Execute toolbar ..............................130
Fill Tools
Simulation...................................137
Find Next........................................135
Find Previous .................................134
First Nibble
Trimmed Sheet ...........................209
Fix Station ......................................119
222
Fixed...................................... 114, 116

For Arc entities ................................ 37
For Holes......................................... 24
For Line entities............................... 37
Formed ............................................ 55
Forming Tools ............................... 109
From Base Line ............................... 14
From Base Point
Simulation .................................. 138
Functions......................... 48, 114, 117
Functions as Pre-Macro or PostMacro......................................... 182
Functions button.............................. 17
Functions have moved to MDL
files ............................................ 181
Functions' List ............................... 119
Global Cut Tab ................................ 59
Global Optimization ......................... 94
Graf ............................................... 135
Graphic Simulation ........................ 135
Group/Ungroup................................ 98
HASP FAQ .................................... 208
he Minimal number of Micro
Joints for this part ........................ 26
Head up........................................... 44
Hole buffer size ............................... 58
Holes ............................................... 20
Holes Tab ........................................ 22
Horizontal ........................................ 40
How do I know on which
computer the License Manager
is running ................................... 209
ID number...................................... 162
In Window.......................................... 4
Inch Tapping Tools........................ 109
Inches users upgrading from
previous versions to 7.xx ........... 184
Index................................................ 11
Insert a G Code ............................. 134
Insert a New Line .......................... 134
Installing and Using the
NetHASP ................................... 207
Installing the cncKad Service
Pack........................................... 193
Installing the Update Manager ...... 195
Internet Options dialog .................. 200
Introduction
New Material List ....................... 185
Punching Manual
ipconfig...........................................207
Irregular............................................55
Key Words for Tool List in NC
and in Report ..............................159
Laser Common Cuts ......................177
Example......................................178
Laser Optimization tab .....................75
Laser Processing Long Parts .........168
Laser Technology Material List ......187
Last Hit on Center ............................30
Last Hit On Center ...........................44
Line section ....................................132
Load On Opposite Side of Pin..........75
Load/Unload Tab..............................74
Loading Mode ..................................74
Loading the prepared NC file .........175
Locking Stations...............................97
Machine section .............................111
Macros ...........................................126
Make Optimization ...........................96
Making the Function available for
cncKad........................................162
Manual Reposition ...........................72
Mark a CAM
Simulation...................................134
Mark Line
Simulation...................................137
Material Choice ................................54
Material Lists ..................................187
Materials Conversion Table ...........189
Max at 1st grip..................................73
Max at last grip.................................73
Max Length ......................................18
Max Used Clamps............................67
Max/Min Processing.........................73
Maximum crunch tool ratio ...............21
Maximum Offset ...............................22
Maximum Width ...............................20
MDLX per machine file...................184
Measure
Simulation...................................138
Micro Joint Parameters Section .......25
MicroJoint.........................................36
Minimum Offset ................................21
Minimum part breaks........................72
Minimum repositions ........................72
Minimum Tool Overlap .....................20
Minimum Tools.................................20
Minimum Width................................ 20
Mirror Allowed ................................. 58
MJ on corners.................................. 25
MJ Width ......................................... 25
MJ Width at Sheet Edge.................. 25
MM Tapping Tools......................... 109
Move................................................ 44
Move from xxx ............................... 140
Multiple Parts with Reposition ....... 201
Multi-tool........................................ 115
Multi-Tool....................................... 122
Multi-Tools section ........................ 119
Name and Path of NC file.............. 128
Names for Special Tool Files 102, 109
Naming a Template ....................... 144
NC Code........................................ 129
NC Code Editing............................ 133
NC exists ......................................... 98
NC Generation Stage 1 ................. 124
NC Program Creation.................... 124
NC to DFT feature ......................... 174
NC tooling...................................... 139
NetHASP on the License PC......... 207
NetHASP utilities ........................... 207
NetHASP.ini .................................. 207
New Material for the Old one......... 190
New MDL Keys.............................. 181
Next Entity's Tangent ...................... 13
NH_TCPIP..................................... 208
Nibble Chain...................................... 6
Nibble Contour .................................. 6
Nibble Entity ...................................... 6
Nibble Start-End ................................ 7
Normal............................................. 55
Notches ........................................... 21
Number of Holes ............................. 63
Number of Parts ........................ 54, 63
OBS Button ................................... 132
Odd hits, then Even hits .................. 20
Offset......................................... 12, 75
Offsets ............................................. 54
Offsets for Repeated Functions..... 218
OK ................................................. 140
223
cncKad
OK (NC Change)............................140
On Arc ................................................4
On Line...............................................3
On Punched Entity .............................5
On Shape Center .............................13
One Hit Only With matching Tool.....23
Open Chute, then Last Hit................44
Open Chute, then Move ...................44
Opening the Simulation..................129
Optimization Path.............................94
Optimization Strategy.................70, 94
Optimizing the Path
Order by List.....................................96
Order by Mouse ...............................96
Ordering by List................................96
Ordering by Mouse...........................97
Ordering the CAMs ..........................96
Oval Tool........................................100
Overlap Definition.............................14
Pan Realtime
Simulation...................................137
Part Area ..........................................64
Part Processing................................69
Part section ......................................63
Part Size View..................................63
Part Tab ...........................................62
Part Weight ......................................64
Parts in Geometry ............................64
Parts in Geometry on Sheet.............65
Pattern............................................134
Pausing the Simulation ..................130
Perforated Sheet ............................203
Perforated Sheet example .............205
Perforating the Sheet .....................204
Perform crunches.............................21
Piercing ............................................61
Pin ....................................................74
Plaintext .........................143, 144, 160
Plasma / Roller / Engrave ..............218
Point Marking Style ..........................62
Point to Point
Simulation...................................138
Positioning (No CAM).......................45
Post Process ..................................143
Predefined Shapes Section..............27
224
Preparatory Cut ............................. 177

Preparing a Geometry for
Common Cut.............................. 177
Preparing the GCD file .................. 174
Pre-tapping...................................... 27
Printing the Library .......................... 89
Private Libraries .............................. 90
Processing with a Sheet
Transformation........................... 173
Profile .............................................. 26
Program Functions .......................... 55
Program Information...................... 132
Program Number........................... 127
Punch All ........................................... 5
Punch and Cut Warnings Tab ......... 28
Punch as Singles............................. 17
Punch Free Hand .............................. 5
Punch Manual ................................... 2
Punch or Cut Functions................... 48
Punching a Perforated Sheet ........ 205
Punching Grids................................ 10
Punching scope............................... 20
Punching sheet edge....................... 29
Push Out (Chute) ...................... 17, 42
Push Out Modes.............................. 43
Push Out Profiles ............................ 44
Quantity of Repositions ................... 72
Radial View ................................... 119
Rapid Tool Path
Simulation .................................. 138
Rectangular Tool ............................. 99
Redraw
Simulation .................................. 137
Reduce Speed for Movement.......... 44
Re-Enabling the DOC Report
Addin.......................................... 216
Release Notes for BOSCHERT
users .......................................... 216
Remove Stripes............................... 70
Remove Turret .............................. 122
Removing an Existing Setup ......... 117
Removing Tool ........................ 70, 119
Renaming a Tool ............................. 89
Report File..................................... 126
Reposition and Head position ......... 42
Reposition and Transformation ....... 41
Reposition Back .............................. 74
Reposition Safety ............................ 73
Punching Manual
Reposition Tab .................................71
Reposition Types .............................96
Repositioning Example Tables.......167
Repositioning principles .................166
Restore Default Clamps ...................81
Restore defaults ...............................67
Round Only ....................................122
Rounded Rectangle .........................99
RTF ................................143, 144, 161
Run Out in cncKad .........................182
Run Simulation After Post
Processor ...................................126
Run the program ..............................55
Running the Simulation ..................129
Save As Predefined Shape ..............30
Save Setup As ...............................114
Scallop Definition .............................16
Scallop for Round Tools...................20
Searching List ................................134
Second Nibble
Trimmed Sheet ...........................209
Select Setup.....................................22
Select Setup File ............................111
Select Sheet.....................................53
Send NC to Diskette
Simulation...................................134
Send to machine
Simulation...................................134
Set CAM Functions ..........................48
Set CAMs to Current ........................42
Set Offsets .......................................32
Set Program Origin ..........................77
Set Sheet = Part...............................53
Set Sheet and Clamps .....................51
Set Tool Sequence...........................37
Setting Offsets..................................31
Setting Stations for Tools .................93
Setting the Machine Version
Parameter...................................218
Setting the tools order
Trimmed Sheet ...........................214
Setting the Trimming
Trimmed Sheet ...........................211
Settings and definitions
Check Stations ...........................140
Setup File section...........................111
Setup file tab ....................................91
Setup tool .......................................116
Setup Tool ..................................... 114

Setup Window ................................. 98
Shapes ............................................ 27
Shapes Tab ..................................... 26
Sheet Area ...................................... 65
Sheet Area and Weight ................... 54
Sheet Dimensions
Perforated Sheet........................ 204
Sheet Loading ......................... 74, 127
Sheet Measuring ............................. 75
Sheet Processing Technology
Tab............................................... 68
Sheet section................................... 65
Sheet Size ....................................... 53
Sheet Tab........................................ 51
Sheet Thickess and Material ........... 61
Sheet Thickness Choice.................. 55
Sheet Transformation with
Reposition.................................. 174
Sheet Type ...................................... 55
Sheet Unloading.............................. 75
Sheet Weight................................... 65
Sheets Quantity............................. 127
Show Clamps Bar
Simulation .................................. 137
Side ................................................. 11
Simulation.............................. 129, 175
Simulation Screen Elements ......... 130
Simulation Speed .......................... 130
Simulation Time............................. 130
Simulation tooling .......................... 139
Single ................................................ 3
Single Punch ..................................... 2
Size of Processed Sheet ................. 75
Size Type ...................................... 115
Slitting.............................................. 22
Slitting tab........................................ 24
Small Introduction.......................... 143
Snake X........................................... 10
Snake Y........................................... 11
Snap Button
Simulation .................................. 131
sort per column.............................. 115
Sorting by Stations .......................... 97
Sorting by Type ............................... 97
Special Punching Section................ 26
Special Tool................................... 102
Special Tools................................. 102
225
cncKad
Split
Simulation...................................136
Square Tool....................................100
Start Parts Placement ......................56
Start process from right side ............74
Starting Corner.................................94
Starting the Simulation ...................130
State Bar
Simulation...................................131
Station ....................................114, 116
Station Angle..................................121
Station Number ..............................121
Station number field .......................118
Station Size ....................................121
Status Bar Enabled
Simulation...................................135
Status Bar On Top
Simulation...................................136
Step Definition..................................15
Stop Button
Simulation...................................131
Stop Machine .............................17, 45
Stop or Push Out..............................17
Stopping the Simulation .................130
Stripe Processing .............................69
Stripe section ...................................70
Stripe width ......................................94
Sub-Routines .................................126
Support for Program Origin ............184
Support for very big arcs ................183
Switch To Setup Layout .................115
Switch To Setup List ......................119
Tapping ............................................27
Tapping Tools ................................109
Technology Parameters ...................55
Technology Table.............................55
Template ........................................143
Template Examples .......................160
Testing the New Special Tool ........108
Testing the Optimization
Testing your Template ...................146
The Function's Structure ................162
The LASTSET File .........................111
The Report File ..............................143
The Tool Reference Line................106
226
Token ............................ 143, 147, 149

Tokens in cncKad.......................... 147
Tolerance Settings .......................... 23
Tonnage .......................................... 83
Tool Button
Simulation .................................. 131
Tool Clearance .............................. 165
Tool Data......................................... 90
Tool Data option .............................. 93
Tool Definitions................................ 98
Tool Field......................................... 82
Tool Functions......................... 98, 119
Tool ID column ................................ 89
Tool information
Simulation .................................. 133
Tool Library tab ............................... 82
Tool Positioning............................... 11
Tool Preview.................................. 118
Tool Report...................................... 90
Tool Reverse Order for
Reposition/Transformation........... 74
Tool Selecting Preferences ............. 20
Tool Sequence ................................ 16
Tool Spacing ................................... 14
Tool Spacing Defaults ..................... 20
Tool Table ....................................... 87
Toolbar...
Simulation .................................. 135
ToolBlockOrder Model Key ........... 159
Tooling............................................. 27
Tooling Changes Example ............ 141
ToolN column .................................. 89
ToolN setting in Tool Library ......... 217
Tool's End Tangent ......................... 13
Tools' List ...................................... 119
Tools Menu...................................... 82
Simulation .................................. 138
Tools' Processing Strategy.............. 69
Tools Quantity ................................. 89
Tools Section................................... 70
ToolSpecific optimization............... 94
Track ............................................. 121
Transformations .............................. 41
Triangular Tool .............................. 100
Trim Sheet Tab................................ 70
Trimmed Sheet.............................. 209
Turret Display ................................ 118
Punching Manual
Turret Management........................139
Turret Setups .................................111
Turret Setups section ...............98, 217
Type Properties................................85
Types of templates.........................144
Uni Directional..................................30
Uni-direction X..................................11
Uni-direction Y..................................11
Unload Part ......................................78
Unloading Mode ...............................75
Update check interval.....................198
Update LASTSET...........................126
Update Manager ............................194
Use Controller Compensation ........126
Use Current NC................................98
Use for conversion .........................190
Use Global .......................................58
Use Part Border ...............................58
Use PrePiercing ...............................61
Use Rectangular Border...................58
Use setup file ...................................24
Use Setup File..................................22
Use Standard Shapes ......................62
Use Tool Data ..................................16
Use tools library ...............................24
Use Tools Library .............................22
Use Vaporize For Engrave...............62
Used Tools .................................49, 92
Used Tools Only.............................140
User Data Tab..................................67
User defined.....................................73
User Defined Movement ..................44
User Defined Tools ........................102
Using Auto Punch
Using Explode Multiple Part
Trimmed Sheet ...........................211
Using Sheet Transformation ..........173
Using the LASTSET file .................112
Using the new list ...........................191
Values that are per Working Unit .. 184

Values translated when switching
between Working Units.............. 185
Vaporization .................................... 61
Vertical ............................................ 39
Wheel Connect................................ 17
Why Trim a Sheet.......................... 209
Width ............................................... 18
Wilson Wheel
Common Cuts............................ 171
Customization ............................ 171
Programming ............................. 170
Tools .......................................... 169
Wilson Wheel Programming in
cncKad....................................... 169
Wilson Wheel Section in the
MDL file...................................... 172
Wilson Wheel Tools....................... 110
Wire ................................................. 37
Wire Joint .................................. 17, 24
Wire Joints Parameters Section ...... 26
Working in the Dead-Zone .............. 66
Working with networked seats....... 194
Working with new setup file........... 217
Workstations with the NetHASP.... 207
Zoom In - F3
Simulation .................................. 136
Zoom out - F4
Simulation .................................. 136
Zoom Part - F5
Simulation .................................. 136
Zoom Previous
Simulation .................................. 136
Zoom Realtime
Simulation .................................. 137
Zoom Sheet - Ctrl+F5
Simulation .................................. 136
Zoom Window - F6
Simulation .................................. 136
227

PunchMan 85

Uploaded by

Copyright:

Available Formats

PunchMan 85

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PunchMan 85

Uploaded by

Copyright:

Available Formats

cncKad

Metalix CAD/CAM LTD

Punch Manual ......................................................................................................... 2

The CAM Menu ..................................................................................................... 31

Push Out Profiles.................................................................................... 44

2.9 Add or Remove Stop Machine ........................................................................ 45

Tools Menu ........................................................................................................... 82

Setup file tab........................................................................................... 91

3.2 Used Tools... ................................................................................................... 92

NC Program Creation.......................................................................................... 124

Automatic Detection ............................................................................. 127

4.6 NC Generation Stage 5 ................................................................................. 128

NC Code Simulation and Editing......................................................................... 129

Appendices ......................................................................................................... 143

A plaintext template example ......................................................... 160

6.2 Creating New Functions ................................................................................ 162

Index ................................................................................................................... 220

You can also click the Add Punch button

from the Common Toolbar

The following dialog will appear:

Punch Free Hand

Dynamic Angle Change

a Single punch on a Punched Entity will look like the following:

This command works on closed contours of circular areas. On rectangular areas it

The following shows crunching of a circular hole:

Crunching a notch with one tool

Crunch Right-Angled Triangle

The area between them will be punched.

There are four options in the grid dropdown list:

- i.e. "-2", in the offset field

Tool's End Tangent

Next Entity's Tangent

This option works only for standard shapes Rounds, Squares,

From Base Line

Cut defined with approximately 75% overlap.

Here the user can set the sequence of the tool.

Use Tool Data

Directional Punch option

Stop or Push Out

(These Wires were made with a Width of 5 for demonstration purposes.)

from the Common Toolbar

Auto Punch Parameters tab

Tool Spacing Defaults

Minimum Tool Overlap

Select a desired minimum Overlap to be used when tool overlap occurs.

Scallop for Round Tools

Cutting Tools Restrictions

In this section some limitations for the tools can be set.

Tool Selecting Preferences

Try, as much as possible, to re-use tools. This reduces efficiency.

Odd hits, then Even hits

Select a strategy for the last punch in the middle:

You can choose which range of entities will be punched.

a the part's outer contour.

Maximum Offset This parameter will be used as a maximum the actual

Use Tools Library

Use Setup File

One Hit Only With matching Tool

In this section, you can order the Auto Punch process: