1|Page

Module 7 : Hydraulic Design of Sewers and Storm Water Drains

Lecture 8 : Hydraulic Design of Sewers and Storm Water Drains (Contd.)

NPTEL IIT Kharagpur Web Courses

2|Page

7.9

Hydraulic Characteristics of Circular Sewer Running Full or Partially Full

Figure 7.1 Section of a circular sewer running partially full

a) Depth at Partial flow

D D

d cos
2
2 2

(6)

b) Therefore proportionate depth

d 1

1 cos
D 2
2

(7)

c) Proportionate area

a
Sin

A 360
2

d) Proportionate perimeter:
360
P

(8)
(9)

e) Proportionate Hydraulic Mean Depth

r 360Sin
1
R
2

f) Proportionate velocity =

(10)

v N r 2/3

V
n R2/3

(11)

In all above equations except everything is constant (Figure 7.1). Hence, for different
values of , all the proportionate elements can be easily calculated. These values of the
hydraulic elements can be obtained from the proportionate graph prepared for different values

NPTEL IIT Kharagpur Web Courses

3|Page

of d/D (Figure 7.2). The value of Mannings n can be considered constant for all depths. In
reality, it varies with the depth of flow and it may be considered variable with depth and
accordingly the hydraulic elements values can be read from the graph for different depth ratio
of flow.
From the plot it is evident that the velocities in partially filled circular sewer sections can
exceed those in full section and it is maximum at d/D of 0.8. Similarly, the discharge obtained
is not maximum at flow full condition, but it is maximum when the depth is about 0.95 times
the full depth.
The sewers flowing with depths between 50% and 80% full need not to be placed on steeper
gradients to be as self cleansing as sewers flowing full. The reason is that velocity and
discharge are function of tractive force intensity which depends upon friction coefficient as
well as flow velocity generated by gradient of the sewer. Using subscript s denoting self
cleansing equivalent to that obtained in full section, the required ratios vs/V, qs/Q and ss/S can
be computed as stated below:

(a) Hydraulic elements for circular sewer

4|Page

(b) Hydraulic elements of circular sewer possessing equal selfcleansing properties at all depths

Figure 7.2 Proportionate graph for circular sewer section (CPHEEO Manual, 1993)
Consider a layer of sediment of unit length, unit width and thickness t, is deposited at the
invert of the sewer (Figure 7.3). Let the slope of the sewer is degree with horizontal. The
drag force or the intensity of tractive force () exerted by the flowing water on a channel is
given by:
= w . R. S

Figure 7.3 A sediment particle moving on the sewer invert

Where,
w = unit weight of water
R = Hydraulic mean depth
S = slope of the invert of the sewer per unit length

(12)

5|Page

With the assumption that the quantity of tractive force intensity at full flow and partial flow
implies equality of cleansing, i.e., for sewers to be same self-cleansing at partial depth as full
depth:
=T
Therefore,

w . r. ss = w . R. S

Hence,

ss = (R/r) S

Or

ss R

S
r

(13)

(14)

Therefore,

vs N r

V
n R

2/3

ss

S

1/ 2

(15)

OR, by substituting r/R = S/ss

1/ 6

vs N r

V
n R

(16)

And
1/ 6

qs N a r

Q n A R

(17)

Example: 2
A 300 mm diameter sewer is to flow at 0.3 depth on a grade ensuring a degree of self cleansing
equivalent to that obtained at full depth at a velocity of 0.9 m/sec. Find the required grade and
associated velocity and rate of discharge at this depth. Assume Mannings rugosity coefficient
n = 0.013. The variation of n with depth may be neglected.
Solution:
Mannings formula for partial depth
v

1 2 / 3 1/ 2
r s
n

For full depth

V

1 2 / 3 1/ 2
R S
N

Using V = 0.90 m/sec, N = n = 0.013 and R = D/4 = 75 mm = 0.075 m

0.90

1
0.075 2 / 3 S 1 / 2
0.013

NPTEL IIT Kharagpur Web Courses

6|Page

S = 0.0043
This is the gradient required for full depth.
and, Q = A.V = /4 (0.3)2 x 0.90 = 0.064 m3/s
At depth d = 0.3D, (i.e., for d/D = 0.3) we have a/A = 0.252 and r/R = 0.684 (neglecting
variation of n)
Now for the sewer to be same self cleansing at 0.3 m depth as it will be at full depth, we have
the gradient (ss) required as ss = (R/r)S
Therefore, ss = S / 0.684
= 0.0043 / 0.0684 = 0.0063
Now, the velocity vs generated at this gradient is given by

Nr
vs V
n R

1/ 6

= 1 x (0.684)1/6 x 0.9
= 0.846 m/s
The discharge qs is given by
1/ 6

N ar
qs Q

n A R
qs

= 1 x (0.258) x (0.939) x (0.064)

= 0.015 m3/s

Example: 3
A combined sewer was designed to serve an area of 60 sq. km with an average population
density of 185 persons/hectare. The average rate of sewage flow is 350 L/Capita/day. The
maximum flow is 50% in excess of the average sewage flow. The rainfall equivalent of 12 mm
in 24 h can be considered for design, all of which is contributing to surface runoff. What will
be the discharge in the sewer? Find the diameter of the sewer if running full at maximum
discharge.
Solution:
Total population of the area = population density x area
= 185 x 60 x 102
= 1110 x 103 persons
Average sewage flow = 350 x 11.1 x 105 Liters/day
= 388.5 x 106 L/day

NPTEL IIT Kharagpur Web Courses

7|Page

= 4.5 m3/sec
Storm water flow

= 60 x 106 x (12/1000) x [1/(24 x 60 x 60)]

= 8.33 m3/sec

Maximum sewage flow

= 1.5 x average sewage flow

= 1.5 x 4.5 = 6.75 m3/sec

Total flow of the combined sewer

= sewage flow + storm flow

= 6.75 + 8.33 = 15.08 m3/sec

Hence, the capacity of the sewer = 15.08 m3/sec

Hence, diameter of the sewer required at the velocity of 0.9 m/s can be calculated as
/4 (D)2 x 0.90 = 15.08 m3/s
Hence, D = 4.62 m

Example: 4
Find the minimum velocity and gradient required to transport coarse sand through a sewer of
40 cm diameter with sand particles of 1.0 mm diameter and specific gravity 2.65, and organic
matter of 5 mm average size with specific gravity 1.2. The friction factor for the sewer
material may be assumed 0.03 and roughness coefficient of 0.012. Consider k = 0.04 for
inorganic solids and 0.06 for organic solids.
Solution
Minimum velocity i.e. self cleansing velocity
Vs

8k
( Ss 1) gd '
f'

Vs

8 x0.04
(2.65 1) x9.81x0.001
0.03
= 0.4155 m/sec say 0.42 m/sec

Similarly, for organic solids this velocity will be 0.396 m/sec

Therefore, the minimum velocity in sewer = 0.42 m/sec
Now, Diameter of the sewer D = 0.4 m
Hydraulic Mean Depth = D/4 = 0.4/4 = 0.1 m
Using Mannings formula:
V = 1/n R2/3 S1/2
0.42 = (1/0.012) x (0.1)2/3 x S1/2

NPTEL IIT Kharagpur Web Courses

8|Page

S = 1/1824.5
Therefore, gradient of the sewer required is 1 in 1824.5.

Example : 5
Design a sewer running 0.7 times full at maximum discharge for a town provided with the
separate system, serving a population 80,000 persons. The water supplied from the water
works to the town is at a rate of 190 LPCD. The mannings n = 0.013 for the pipe material and
permissible slope is 1 in 600. Variation of n with depth may be neglected. Check for
minimum and maximum velocity assuming minimum flow 1/3 of average flow and maximum
flow as 3 times the average. (for d/D = 0.7, q/Q = 0.838, v/V = 1.12)
Solution
Average water supplied = 80000 x 190 x (1/24 x 60 x 60 x 1000) = 0.176 m3/sec
Sewage production per day, (considering 80% of water supply) = 0.176 x 0.8 = 0.14 m3/sec
Maximum sewage discharge = 3 x 0.14 = 0.42 m3/sec
Now for d/D = 0.7, q/Q = 0.838, v/V = 1.12
Therefore, Q = 0.42/0.838 = 0.5 m3/sec
Now
1 D 2 D
Q

n 4 4
Q

1 D 2
0.013 4

2/3

S 1/ 2

D

4

2/3

600

1/ 2

Therefore, D = 0.78 m
V = Q/A = 1.04 m/sec
Now, v/V = 1.12
Therefore v = 1.12 x 1.04 = 1.17 m/sec
This velocity is less than limiting velocity hence, OK
Check for minimum velocity
Now qmin = 0.14/3 = 0.047 m3/sec
qmin/Q = 0.047/0.5 = 0.09
From proportional chart, for q/Q = 0.09, d/D = 0.23 and v/V = 0.65
Therefore, the velocity at minimum flow = 0.65 x 1.04 = 0.68 m/sec
This velocity is greater than self cleansing velocity, hence OK
dmin = 0.23 x 0.78 = 0.18 m

NPTEL IIT Kharagpur Web Courses

9|Page

Comment: If the velocity at minimum flow is not satisfactory, increase the slope or try with
reduction in depth of flow at maximum discharge or reduction in diameter of the sewer.
Assignment: Solve the above problem with population 100000 persons and pipe flowing 0.75
full at maximum discharge. The rate of water supply is 150 LPCD, n = 0.013, and permissible
S = 1 in 600.

NPTEL IIT Kharagpur Web Courses