EK

YSCC18FSAADG

This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or
repair the product or products dealt with in this service information by anyone else could result in serious injury or death

YSCC18FSAADG

Table of Contents

1. Features..................................................................................................... 1
2. Introduction ............................................................................................... 2
3. Specifications ............................................................................................ 7
4. Printed circuit board connector wiring diagram .................................... 9
5. Functions and control ............................................................................. 10
5.1 Main functions and control specification .................................................. 10
5.2 Value of thermistor ................................................................................... 13
6. System configuration ............................................................................... 21
6.1 System configuration ................................................................................ 21
6.2 Instruction ................................................................................................. 22
7. Service diagnosis .................................................................................... 29
7.1 Problem symptoms and measures .......................................................... 29
7.2 Error codes and description indoor display .............................................. 29
8. Capacity diagrams and curves diagrams ............................................... 32
9. Installations ............................................................................................... 34
10.Wiring Diagrams ....................................................................................... 38
11. Description of coding rules of unit model ............................................. 45

Domestic Air Conditioner

YSCC18FSAADG

Table of Contents

Domestic Air Conditioner

YSCC18FSAADG

Table of Contents

2. Introduction
2.1 Safety Cautions
Be sure to read the following safety cautions before conducting repair work.
The caution items are classified into Warning and Caution. The Warning items are especially important
since they can lead to death or serious injury if they are not followed closely. The Caution items can also lead
to serious accidents under some conditions if they are not followed. Therefore, be sure to observe all the safety
caution items described below.
About the pictograms
This symbol indicates an item for which caution must be exercised.
The pictogram shows the item to which attention must be paid.
This symbol indicates a prohibited action.
The prohibited item or action is shown inside or near the symbol.
This symbol indicates an action that must be taken, or an instruction.
The instruction is shown inside or near the symbol.
After the repair work is complete, be sure to conduct a test operation to ensure that the equipment operates
normally, and explain the cautions for operating the product to the customer.

2.1.1 Caution in Repair

Warning
Be sure to disconnect the power cable plug from the plug socket before disassembling the equipment for
a repair.
Working on the equipment that is connected to a power supply can cause an electrical shook.
If it is necessary to supply power to the equipment to conduct the repair or inspecting the circuits, do not
touch any electrically charged sections of the equipment.
If the refrigerant gas discharges during the repair work, do not touch the discharging refrigerant gas.The
refrigerant gas can cause frostbite.
When disconnecting the suction or discharge pipe of the compressor at the welded section, release the
refrigerant gas completely at a well-ventilated place first.
If there is a gas remaining inside the compressor, the refrigerant gas or refrigerating machine oil
discharges when the pipe is disconnected, and it can cause injury.
If the refrigerant gas leaks during the repair work, ventilate the area. The refrigerant gas can generate
toxic gases when it contacts flames.
The step-up capacitor supplies high-voltage electricity to the electrical components of the outdoor unit.
Be sure to discharge the capacitor completely before conducting repair work.A charged capacitor can
cause an electrical shock.
Do not start or stop the air conditioner operation by plugging or unplugging the power cable plug.
Plugging or unplugging the power cable plug to operate the equipment can cause an electrical shock or
fire.

Domestic Air Conditioner

YSCC18FSAADG

Introduction

Warning
Do not repair the electrical components with wet hands. Working on the equipment with wet hands can
cause an electrical shock.
Do not clean the air conditioner by splashing water. Washing the unit with water can cause an electrical
shock.

Be sure to provide the grounding when repairing the equipment in a humid or wet place, to avoid electrical
shocks.

Be sure to turn off the power switch and unplug the power cable when cleaning the equipment. The
internal fan rotates at a high speed, and cause injury.

Do not tilt the unit when removing it. The water inside the unit can spill and wet the furniture and floor.

Be sure to check that the refrigerating cycle section has cooled down sufficiently before conducting repair
work. Working on the unit when the refrigerating cycle section is hot can cause burns.
Use the welder in a well-ventilated place. Using the welder in an enclosed room can cause oxygen
deficiency.

2.1.2 Cautions Regarding Products after Repair

Warning
Be sure to use parts listed in the service parts list of the applicable model and appropriate tools to
conduct repair work. Never attempt to modify the equipment. The use of inappropriate parts or tools can
cause an electrical shock, excessive heat generation or fire.
When relocating the equipment, make sure that the new installation site has sufficient strength to
withstand the weight of the equipment.
If the installation site does not have sufficient strength and if the installation work is not conducted
securely, the equipment can fall and cause injury.
Be sure to install the product correctly by using the provided standard installation frame.

For

Incorrect use of the installation frame and improper installation can cause the equipment to fall, resulting
in injury.

integral
units only

Be sure to install the product securely in the installation frame mounted on a window frame.
If the unit is not securely mounted, it can fall and cause injury.

For
integral
units only

Domestic Air Conditioner

Introduction

YSCC18FSAADG

Warning
Be sure to use an exclusive power circuit for the equipment, and follow the technical standards related to
the electrical equipment, the internal wiring regulations and the instruction manual for installation when
conducting electrical work.
Insufficient power circuit capacity and improper electrical work can cause an electrical shock or fire.
Be sure to use the specified cable to connect between the indoor and outdoor units. Make the
connections securely and route the cable properly so that there is no force pulling the cable at the
connection terminals.
Improper connections can cause excessive heat generation or fire.
When connecting the cable between the indoor and outdoor units, make sure that the terminal cover does
not lift off or dismount because of the cable.
If the cover is not mounted properly, the terminal connection section can cause an electrical shock,
excessive heat generation or fire.
Do not damage or modify the power cable.
Damaged or modified power cable can cause an electrical shock or fire. Placing heavy items on the
power cable, and heating or pulling the power cable can damage the cable.
Do not mix air or gas other than the specified refrigerant (R-410A / R22) in the refrigerant system.
If air enters the refrigerating system, an excessively high pressure results, causing equipment damage
and injury.
If the refrigerant gas leaks, be sure to locate the leak and repair it before charging the refrigerant. After
charging refrigerant, make sure that there is no refrigerant leak.
If the leak cannot be located and the repair work must be stopped, be sure to perform pump-down and
close the service valve, to prevent the refrigerant gas from leaking into the room. The refrigerant gas itself
is harmless, but it can generate toxic gases when it contacts flames, such as fan and other heaters,
stoves and ranges.
When replacing the coin battery in the remote controller, be sure to disposed of the old battery to prevent
children from swallowing it.
If a child swallows the coin battery, see a doctor immediately.

Caution
Installation of a leakage breaker is necessary in some cases depending on the conditions of the
installation site, to prevent electrical shocks.
Do not install the equipment in a place where there is a possibility of combustible gas leaks.
If a combustible gas leaks and remains around the unit, it can cause a fire.
Be sure to install the packing and seal on the installation frame properly. If the packing and seal are not
installed properly, water can enter the room and wet the furniture and floor.

For
integral
units only

Domestic Air Conditioner

Introduction

YSCC18FSAADG

2.1.3 Inspection after Repair

Warning
Check to make sure that the power cable plug is not dirty or loose, then insert the plug into a power outlet
all the way.
If the plug has dust or loose connection, it can cause an electrical shock or fire.
If the power cable and lead wires have scratches or deteriorated, be sure to replace them.
Damaged cable and wires can cause an electrical shock, excessive heat generation or fire.

Warning
Do not use a joined power cable or extension cable, or share the same power outlet with other electrical
appliances, since it can cause an electrical shock, excessive heat generation or fire.

Caution
Check to see if the parts and wires are mounted and connected properly, and if the connections at the
soldered or crimped terminals are secure. Improper installation and connections can cause excessive
heat generation, fire or an electrical shock.
If the installation platform or frame has corroded, replace it. Corroded installation platform or frame can
cause the unit to fall, resulting in injury.
Check the grounding, and repair it if the equipment is not properly grounded. Improper grounding can
cause an electrical shock.
Be sure to measure the insulation resistance after the repair, and make sure that the resistance is 1 M
ohm or higher.
Faulty insulation can cause an electrical shock.
Be sure to check the drainage of the indoor unit after the repair.
Faulty drainage can cause the water to enter the room and wet the furniture and floor.

Domestic Air Conditioner

Introduction

YSCC18FSAADG

2.1.4 Using Icons

Icons are used to attract the attention of the reader to specific information. The meaning of each icon is described in
the table below:

2.1.5 Using Icons List

Icon

Type of Information

Description
A note provides information that is not indispensable, but may

Note:

Note

nevertheless be valuable to the reader, such as tips and tricks.

A caution is used when there is danger that the reader, through

Caution

Caution

incorrect manipulation, may damage equipment, loose data, get an

unexpected result or has to restart (part of) a procedure.

Warning

Warning

A warning is used when there is danger of personal injury.

A reference guides the reader to other places in this binder or in

Reference

this manual, where he/she will find additional information on a

specific topic.

Domestic Air Conditioner

Specifications

YSCC18FSAADG

HSU18VCK

Model

Cooling
5.27/5.12

KW
Capacity Rated

Btu/h

18000/17500

kcl/h

4532/4408

POWER SUPP LY
NOMINAL
DISTRIBUTION
SYSTEM
VO LTAGE

VM
Phase
Frequency
Voltage

1PH
60

HZ

230/208V

Moisture Removal

L/h

4.0

Running Current(Rated)

7.2/7.6

Power Consumption Rated

1600/1550

EER Rated

3.3

W/W

Piping Connections
(external diameter)

Liquid

mm

6.35

Gas

mm

9.52

Drain

mm

16

Heat Insulation

Both liquid and Gas Pipes

Max.Piping Length

10

Max.Level Di fference

Chargeless

g/m

20

Amount of Additional Charge of Refrigerant

Indoor Unit
Front Panel Color

Air Flow Rate

Mat Crystal Silver

m/ min(cfm)

14.5(511.9)

13.3(469.2)

12.08(426.5)

Type
Fan

Motor Output
Speed

Cross Flow Fan

W
4 Steps,Auto

Steps

Air Direction Control

Right,Left,Horizontal,Downward

Air Filter

Removable/ Washable/Mildew Proof

Run current(rated)

0.1

Power consumption

25
Microcomputer Control

Temperature Control
Dimensions(WxDxH)

mm

1046X299X234

Packaged Dimensions(WxDxH)

mm

1126X388X344

Weight

kg

Gross Weight

kg

Operation Sound
Sound Power

H/M/L
H(cooling/heating)

13
16.5
49/46.5/43.5

dBA
dBA

59

Domestic Air Conditioner

Specifications

YSCC18FSAADG

Outdoor Unit

HSU18VCK

Casing Color

lvory white
Type

Hermetic motor compressor

50A452P

Model
Compressor

Motor Output

NMOC Ze-Gles RB68EP or equivalent

Oil Type
Oil Charge

1805

0.56

Model
Refrigerant

Air Flow Rate

(H/L)

Charge

R410A
1.3

kg

50

m/min
cfm

1765
Axial fan

Type
Fan

27

Runing current(rated)

7.2/7.6

Power Consumption(rated)

1600/1550

Motor Output

Dimensions(WxDxH)(stop valve,
and bottom support is not included)

mm

Packaged Dimensions(WxDxH)

mm

Weight
Gross Weight
Operation Sound
Sound Power

H
H(cooling/heating)

860X308X730
995X420X815

kg

46.5

kg

50.5

dBA

60

dBA

70

Domestic Air Conditioner

YSCC18FSAADG

Connector Wiring Diagram

4. Printed Circuit Board Connector Wiring Diagram

4.1 Indoor unit
Connectors Indoor PCB
1) CH1 connector for power line L.
2) CN26 connector for DC fan motor.
3) CN11 connector for step motor.
4) CN32 connector for receiver display.
5) CN48 connector for Emergency switch.
6) CN1 connector for ambient temp. sensor and piping temp.sensor.
7) CN54 connector for power line N.
8) CON38 connector for compressor control.

CH1

CN54

CN26

CN11

CN32

CN48

CN1

CON38

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

5 Functions and control

5.1 main functions and control specifications
Including brief introduction to air conditioners of series models and electric control function.
5.1.1 Automatic running
(1) Single cold automatic run mode:
After entering into this mode, the main control MCU determines the corresponding work pattern according
to the indoor temperature so as to maintain the preset temperature (the preset temperature is 78 F). When
the indoor temperature is below 78 F, outlet air from compressor is off, the automatic wind from fan motor
is low, and wind can be set to high, medium or low by hand. When the indoor temperature is or above 78 F,
the unit enters the cooling mode and conducts the cooling programme (the preset temperature is 78 F),
outlet air from compressor is on and indoor fan motor run in fixed wind speed
5.1.2 Indoor temperature control
Temperature control range : 60F ---86F
Temperature control precision: 2F
Compressor cant be controlled by temperature sensor within 2 minutes after it starts
Cooling mode:
When Tr> Ts, outdoor fan motor and compressor on, and indoor fan motor run at fixed wind speed. When Tr
< Ts, outdoor fan motor and compressor off, and when Tr > Ts, outdoor fan motor and compressor are working
again .If Tr=Ts, the indoor fan motor , outdoor fan motor and the compressors state will not change.
5.1.3 Cooling run mode:

emperature control range : 60F ---86F

temperature control precision:2F
compressor cant be controlled by temperature sensor within 2 minutes after it starts.
control character: when TrTs, outlet air from compressor is on and indoor fan motor run at fixed wind
speed. When Tr< Ts, outlet air from compressor is off , and when Tr>Ts, outlet air from compressor is on.
wind speed control: (the temperature difference?is)1
auto: When Tr>=Ts+5F, the wind speed is high;
When Ts+1F Tr<Ts+5F , the wind speed is medium.
When Tr<Ts+1F , the wind speed is low.
When temperature sensor is off, the fan motor runs at low speed.
when the wind speed changes from low to high, there is no delay, and when it changes from high
to low, there is a 3-minutes delay before conversion.
Manual operation:When unit is on the wind speed can be set to high, medium, low or automatic as
required(execute instruction 2 seconds later after receiving remote signal)
Compressor control The compressor cant be controlled by temperature sensor within 2 minutes after
start up and can be only restarted at least 3 minutes later after shutdown. There is no 3-minute protection
withpower on for the first time (over 3 minutes with power off). The compressor must stands by for 3
minutesbefore it is restarted after shut down.
There is no 2-minute limit when changing the temperature setting or shutting down the machine through
the remote controller, and the machine can be shut down immediately.
Avoiding electrical shock: outlet air is available 2 seconds later after startup.
High temperature expiration protection:

10

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

(1)High temperature expiration prevention:When the temp.of coil pipe is above 161F,compressor
and outlet air stop running 10 seconds later, and inlet air runs as the temp. sensor is off. When compressor stands by for 3 minute and the temp. of coil pipe is below 149F, the unit can be started again.
Protection of frost is available (disable in test run or heating mode): In order to prevent the indoor
heat exchanger from freezing (in refrigation or dehumidifying mode), the compressor will be shut off
when the temperature of the indoor coil pipe is or below 30F and the compressor runs for over 5 minutes.when the temperature of the indoor coil pipe ascends to over 44F, the compressor is restarted
(must meet a 3-minutes delay)
Timer on, Timer off and sleep control are available.
5.1.4 Dehumidifying mode

Temperature control range :60F ---86F

Control character:
When Tr (indoor temperature)> Ts (temperature setting) +3F, compressor and outdoor fan motor
run continuosly with indoor fan motor runnig in accordance with the wind speed setting(State 1).
When Ts Tr Ts +3 F, outlet air from compressor is on for 10 minutes and off for 6 minutes, the
indoor fan motor is off in 3 minutes after shut down of compressor and gives breeze in other time (State 2).
When Tr < Ts, outlet air from compressor is unavailable, and the indoor fan motor enter breeze
mode 3 minutes later after after shut down of compressor(State 3).

When all the ranges alternate, there is1F difference.

.
5.1.5 Timer function:

You can set 24-hour timer on or timer off as required, and the minum time unit is 1 minute. After
setting, the indicator of indoor unit is on , and it is off when timer setting is completed. There are several
timer mode as follows.
5.1.5.1 Timer on: The LED of timer on lights up, and unit behaves with halt status. Timer on is
completed, and then unit starts running with the LED of timer on off. The unit starts with the the last
setting receiving timer signals, and sleep setting is not allowed.
5.1.5.2 Timer off: Unit starts, timer indicator lights up; When reaching time setting, the indicator
goes out, unit enters shut down mode, and sleep function can be set. If timer off and sleep are set
synchronously, the one which time is short run first. Executing shutdown instruction clear timer and sleep
function.
5.1.5.3 Timer on and timer off can be set synchronously.
5.1.6 Sleep function: the timer indicator lights up.

5.1.6.1 In cooling/defrosting mode, the temp. setting increases 1 F one hour later after start up.
After another hour the temp. setting increase by more 1 F and then run continuously for another 6

11

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

hours and then close.

5.1.6.2 In heating mode, the temp. setting decrease 3 F one hour after start up. After another hour the
temp. setting decrease by more 3 F. After 3 hours the temp. setting rise by 1 F and then run
continuously for another 3 hours and then close

5.1.6.3 If the wind speed is set to high before going to bed, the wind speed become medium after
start up; If the wind speed is set to medium before going to bed, the wind speed become low after start
up; If the wind speed is set to low before going to bed, the wind speed keep unchanged.

5.1.7

Emergency switch imput:

5.1.7.1 Press the switch of emergency operation, then buzzer rings once and unit enters the
automatic operation mode. (emergency operation)
5.1.7.2 If the switch is kept pressed for 5 seconds, buzzer ring two times and unit enter enter test
run mode.
5.1.7.3 Press the switch again, and then closes.
5.1.7.4 Enter emergency operation from timer mode, then timer is cancelled.
5.1.8 Test run:
5.1.8.1 The temperature sensor of inlet air doesnt work, and compressor starts (but subject to the
limit of -minute delay excluding the first time), and high wind, cooling, and air door is open.The indoor fan
motor runs, running indicator lights up, compressor relay and the one of outdoor fan motor is closed
5.1.8.2 During test run:
The prevention of freezing of evaporator doesnt work.
Current cross control doesnt work.
The control of current cross peak expiration doesnt work.
Temperature control doesnt work.
Temperature expiration control doesnt work.
5.1.9 memory function The memory function of power down is available, and the auto recovery

12

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

function of power on is optional. (In auto, heating, cooling, or defrosting status, press the
to enter additional options when cycle dispay to
press

and then press

button

will flash and then press

quickly

rapidly 10 times within 6 seconds, and the auto recovery function

of power on can be set on/off. If the buzzer rings 4 times, the the auto recovery function of power on is
available; If the buzzer rings 2 times, the the auto recovery function of power on is unavailable.)
If there is no EEPROM, the unit is taken off the off function of the memory function of power down. But
the memory function of power down can also be set on/off, and the data is the default value of chip

5.2 Value of Thermistor

5.2.1 Indoor unit
Room sensor
R25 =23K3.5%
B25

/50 =4200K3%
Max.(K)

Normal(K

0LQ.

-30

568.8372

501.0746

440.8435

-1.97

1.75

-29

530.9600

468.6491

413.1441

-1.95

1.74

-28

495.8488

438.5314

387.3645

-1.93

1.72

-27

463.2850

410.5433

363.3602

-1.91

1.71

-26

433.0683

384.5212

340.9980

-1.90

1.70

-25

405.0156

360.3153

320.1558

-1.88

1.69

-24

378.9588

337.7879

300.7211

-1.86

1.67

-23

354.7440

316.8126

282.5905

-1.84

1.66

-22

332.2300

297.2732

265.6686

-1.82

1.64

-21

311.2873

279.0627

249.8676

-1.80

1.63

-20

291.7969

262.0831

235.1067

-1.78

1.62

-19

273.6494

246.2437

221.3111

-1.76

1.60

-18

256.7445

231.4612

208.4122

-1.74

1.59

-17

240.9897

217.6590

196.3462

-1.72

1.57

-16

226.3000

204.7662

185.0545

-1.70

1.56

-15

212.5973

192.7176

174.4829

-1.68

1.54

-14

199.8093

181.4531

164.5813

-1.66

1.53

-13

187.8698

170.9169

155.3033

-1.64

1.51

-12

176.7176

161.0578

146.6059

-1.62

1.49

-11

166.2961

151.8284

138.4495

-1.60

1.48

-10

156.5532

143.1847

130.7973

-1.58

1.46

-9

147.4409

135.0863

123.6153

-1.56

1.44

-8

138.9148

127.4956

116.8717

-1.53

1.43

-7

130.9337

120.3778

110.5374

-1.51

1.41

-6

123.4597

113.7009

104.5852

-1.49

1.39

-5

116.4577

107.4349

98.9897

-1.47

1.38

Temp.(

13

Tolerance(

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

-4

109.8953

101.5523

93.7278

-1.45

1.36

-3

103.7422

96.0274

88.7774

-1.43

1.34

-2

97.9708

90.8365

84.1185

-1.40

1.32

-1

92.5551

85.9574

79.7322

-1.38

1.30

87.4712

81.3697

75.6011

-1.36

1.29

82.6970

77.0544

71.7088

-1.34

1.27

78.2118

72.9937

68.0402

-1.31

1.25

73.9966

69.1712

64.5813

-1.29

1.23

70.0335

65.5716

61.3188

-1.27

1.21

66.3062

62.1807

58.2405

-1.24

1.19

62.7992

58.9853

55.3351

-1.22

1.17

59.4984

55.9729

52.5917

-1.20

1.15

56.3905

53.1320

50.0006

-1.17

1.13

53.4631

50.4521

47.5523

-1.15

1.11

10

50.7048

47.9230

45.2384

-1.13

1.09

11

48.1049

45.5355

43.0505

-1.10

1.07

12

45.6534

43.2808

40.9813

-1.08

1.04

13

43.3410

41.1509

39.0236

-1.05

1.02

14

41.1592

39.1381

37.1708

-1.03

1.00

15

39.0998

37.2355

35.4167

-1.00

0.98

16

37.1553

35.4363

33.7555

-0.98

0.96

17

35.3186

33.7344

32.1818

-0.95

0.94

18

33.5833

32.1240

30.6905

-0.93

0.91

19

31.9432

30.5997

29.2769

-0.90

0.89

20

30.3925

29.1565

27.9365

-0.88

0.87

21

28.9259

27.7895

26.6651

-0.85

0.84

22

27.5383

26.4944

25.4589

-0.83

0.82

23

26.2252

25.2670

24.3140

-0.80

0.80

24

24.9822

24.1034

23.2271

-0.78

0.77

25

23.8050

23.0000

22.1950

-0.78

0.77

26

22.7500

21.9499

21.1520

-0.78

0.78

27

21.7477

20.9536

20.1638

-0.82

0.81

28

20.7951

20.0081

19.2272

-0.86

0.85

29

19.8895

19.1104

18.3394

-0.89

0.88

30

19.0285

18.2581

17.4974

-0.93

0.92

31

18.2094

17.4484

16.6988

-0.97

0.95

32

17.4302

16.6792

15.9410

-1.00

0.99

33

16.6885

15.9480

15.2217

-1.04

1.02

34

15.9825

15.2530

14.5389

-1.08

1.06

35

15.3103

14.5920

13.8903

-1.12

1.09

36

14.6700

13.9632

13.2743

-1.16

1.13

37

14.0599

13.3650

12.6889

-1.20

1.16

38

13.4786

12.7957

12.1325

-1.23

1.20

14

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

39

12.9244

12.2537

11.6035

-1.27

1.24

40

12.3960

11.7375

11.1004

-1.31

1.27

41

11.8921

11.2459

10.6218

-1.35

1.31

42

11.4113

10.7775

10.1665

-1.39

1.34

43

10.9526

10.3311

9.7330

-1.43

1.38

44

10.5147

9.9056

9.3204

-1.48

1.42

45

10.0967

9.4999

8.9275

-1.52

1.45

46

9.6976

9.1130

8.5532

-1.56

1.49

47

9.3163

8.7439

8.1965

-1.60

1.53

48

8.9521

8.3916

7.8566

-1.64

1.57

49

8.6040

8.0554

7.5327

-1.68

1.60

50

8.2713

7.7345

7.2237

-1.73

1.64

51

7.9531

7.4280

6.9291

-1.77

1.68

52

7.6489

7.1353

6.6480

-1.81

1.72

53

7.3580

6.8556

6.3797

-1.85

1.76

54

7.0796

6.5884

6.1237

-1.90

1.79

55

6.8131

6.3329

5.8793

-1.94

1.83

56

6.5581

6.0887

5.6459

-1.99

1.87

57

6.3140

5.8552

5.4230

-2.03

1.91

58

6.0802

5.6318

5.2100

-2.07

1.95

59

5.8563

5.4181

5.0065

-2.12

1.99

60

5.6417

5.2136

4.8120

-2.16

2.03

61

5.4361

5.0178

4.6260

-2.21

2.07

62

5.2391

4.8304

4.4481

-2.25

2.11

63

5.0502

4.6510

4.2780

-2.30

2.15

64

4.8691

4.4791

4.1153

-2.35

2.19

65

4.6954

4.3145

3.9596

-2.39

2.23

66

4.5287

4.1567

3.8105

-2.44

2.27

67

4.3689

4.0055

3.6678

-2.49

2.31

68

4.2154

3.8605

3.5312

-2.53

2.35

69

4.0682

3.7216

3.4004

-2.58

2.39

70

3.9268

3.5883

3.2750

-2.63

2.43

71

3.7910

3.4605

3.1549

-2.68

2.48

72

3.6606

3.3378

3.0398

-2.73

2.52

73

3.5353

3.2201

2.9294

-2.77

2.56

74

3.4150

3.1072

2.8237

-2.82

2.60

75

3.2993

2.9987

2.7222

-2.87

2.64

76

3.1881

2.8946

2.6249

-2.92

2.68

77

3.0812

2.7946

2.5316

-2.97

2.73

78

2.9785

2.6986

2.4420

-3.02

2.77

79

2.8796

2.6063

2.3560

-3.07

2.81

80

2.7845

2.5176

2.2735

-3.12

2.86

81

2.6931

2.4324

2.1943

-3.17

2.90

15

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

82

2.6050

2.3505

2.1182

-3.22

2.94

83

2.5203

2.2717

2.0451

-3.28

2.99

84

2.4388

2.1960

1.9749

-3.33

3.03

85

2.3602

2.1231

1.9075

-3.38

3.07

86

2.2846

2.0530

1.8426

-3.43

3.12

87

2.2118

1.9856

1.7803

-3.48

3.16

88

2.1416

1.9207

1.7204

-3.54

3.20

89

2.0740

1.8582

1.6628

-3.59

3.25

90

2.0089

1.7981

1.6074

-3.64

3.29

91

1.9461

1.7402

1.5541

-3.70

3.34

92

1.8856

1.6844

1.5028

-3.75

3.38

93

1.8272

1.6307

1.4535

-3.80

3.43

94

1.7709

1.5789

1.4060

-3.86

3.47

95

1.7166

1.5291

1.3603

-3.91

3.52

96

1.6643

1.4810

1.3163

-3.97

3.56

97

1.6138

1.4347

1.2739

-4.02

3.61

98

1.5650

1.3900

1.2331

-4.08

3.66

99

1.5180

1.3470

1.1937

-4.13

3.70

100

1.4726

1.3054

1.1559

-4.19

3.75

101

1.4287

1.2654

1.1194

-4.24

3.80

102

1.3864

1.2268

1.0842

-4.30

3.84

103

1.3455

1.1895

1.0503

-4.36

3.89

104

1.3060

1.1535

1.0176

-4.42

3.94

105

1.2679

1.1188

0.9860

-4.47

3.98

106

1.2310

1.0853

0.9556

-4.53

4.03

107

1.1954

1.0529

0.9263

-4.59

4.08

108

1.1610

1.0217

0.8980

-4.65

4.13

109

1.1277

0.9915

0.8707

-4.70

4.17

110

1.0955

0.9624

0.8443

-4.76

4.22

111

1.0644

0.9342

0.8189

-4.82

4.27

112

1.0344

0.9070

0.7943

-4.88

4.32

113

1.0053

0.8807

0.7706

-4.94

4.37

114

0.9771

0.8553

0.7478

-5.00

4.41

115

0.9499

0.8307

0.7256

-5.06

4.46

116

0.9235

0.8070

0.7043

-5.12

4.51

117

0.8980

0.7840

0.6837

-5.18

4.56

118

0.8734

0.7618

0.6637

-5.24

4.61

119

0.8495

0.7404

0.6445

-5.30

4.66

120

0.8263

0.7196

0.6258

-5.36

4.71

16

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

Pipe Sensor
R25 =10K3%
B25

/50 =3700K3%
Max.(K)

Normal(K

0LQ.

-30

165.2170

147.9497

132.3678

-1.94

1.75

-29

155.5754

139.5600

125.0806

-1.93

1.74

-28

146.5609

131.7022

118.2434

-1.91

1.73

-27

138.1285

124.3392

111.8256

-1.89

1.71

-26

130.2371

117.4366

105.7989

-1.87

1.70

-25

122.8484

110.9627

100.1367

-1.85

1.69

-24

115.9272

104.8882

94.8149

-1.83

1.67

-23

109.4410

99.1858

89.8106

-1.81

1.66

-22

103.3598

93.8305

85.1031

-1.80

1.64

-21

97.6556

88.7989

80.6728

-1.78

1.63

-20

92.3028

84.0695

76.5017

-1.76

1.62

-19

87.2775

79.6222

72.5729

-1.74

1.60

-18

82.5577

75.4384

68.8710

-1.72

1.59

-17

78.1230

71.5010

65.3815

-1.70

1.57

-16

73.9543

67.7939

62.0907

-1.68

1.55

-15

70.0342

64.3023

58.9863

-1.66

1.54

-14

66.3463

61.0123

56.0565

-1.64

1.52

-13

62.8755

57.9110

53.2905

-1.62

1.51

-12

59.6076

54.9866

50.6781

-1.60

1.49

-11

56.5296

52.2278

48.2099

-1.58

1.47

-10

53.6294

49.6244

45.8771

-1.56

1.46

-9

50.8956

47.1666

43.6714

-1.54

1.44

-8

48.3178

44.8454

41.5851

-1.51

1.42

-7

45.8860

42.6525

39.6112

-1.49

1.40

-6

43.5912

40.5800

37.7429

-1.47

1.39

-5

41.4249

38.6207

35.9739

-1.45

1.37

-4

39.3792

36.7676

34.2983

-1.43

1.35

-3

37.4465

35.0144

32.7108

-1.41

1.33

-2

35.6202

33.3552

31.2062

-1.38

1.31

-1

33.8936

31.7844

29.7796

-1.36

1.29

32.2608

30.2968

28.4267

-1.34

1.28

30.7162

28.8875

27.1431

-1.32

1.26

29.2545

27.5519

25.9250

-1.29

1.24

27.8708

26.2858

24.7686

-1.27

1.22

26.5605

25.0851

23.6704

-1.25

1.20

25.3193

23.9462

22.6273

-1.23

1.18

24.1432

22.8656

21.6361

-1.20

1.16

23.0284

21.8398

20.6939

-1.18

1.14

Temp.((

))

17

Tolerance(

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

21.9714

20.8659

19.7982

-1.15

1.12

20.9688

19.9409

18.9463

-1.13

1.09

10

20.0176

19.0621

18.1358

-1.11

1.07

11

19.1149

18.2270

17.3646

-1.08

1.05

12

18.2580

17.4331

16.6305

-1.06

1.03

13

17.4442

16.6782

15.9315

-1.03

1.01

14

16.6711

15.9601

15.2657

-1.01

0.99

15

15.9366

15.2770

14.6315

-0.98

0.96

16
17

15.2385
14.5748

14.6268

14.0271

14.0079

13.4510

-0.96
-0.93

0.94
0.92

18

13.9436

13.4185

12.9017

-0.91

0.90

19

13.3431

12.8572

12.3778

-0.88

0.87

20

12.7718

12.3223

11.8780

-0.86

0.85

21

12.2280

11.8126

11.4011

-0.83

0.83

22

11.7102

11.3267

10.9459

-0.81

0.80

23

11.2172

10.8634

10.5114

-0.78

0.78

24

10.7475

10.4216

10.0964

-0.75

0.75

25

10.3000

10.0000

9.7000

-0.75

0.75

26

9.8975

9.5974

9.2980

-0.76

0.76

27

9.5129

9.2132

8.9148

-0.80

0.80

28

9.1454

8.8465

8.5496

-0.84

0.83

29

8.7942

8.4964

8.2013

-0.87

0.86

30

8.4583

8.1621

7.8691

-0.91

0.90

31

8.1371

7.8428

7.5522

-0.95

0.93

32

7.8299

7.5377

7.2498

-0.98

0.97

33

7.5359

7.2461

6.9611

-1.02

1.00

34

7.2546

6.9673

6.6854

-1.06

1.04

35

6.9852

6.7008

6.4222

-1.10

1.07

36

6.7273

6.4459

6.1707

-1.13

1.11

37

6.4803

6.2021

5.9304

-1.17

1.14

38

6.2437

5.9687

5.7007

-1.21

1.18

39

6.0170

5.7454

5.4812

-1.25

1.22

40

5.7997

5.5316

5.2712

-1.29

1.25

41

5.5914

5.3269

5.0704

-1.33

1.29

42

5.3916

5.1308

4.8783

-1.37

1.33

43

5.2001

4.9430

4.6944

-1.41

1.36

44

5.0163

4.7630

4.5185

-1.45

1.40

45

4.8400

4.5905

4.3500

-1.49

1.44

46

4.6708

4.4252

4.1887

-1.53

1.47

47

4.5083

4.2666

4.0342

-1.57

1.51

48

4.3524

4.1145

3.8862

-1.61

1.55

49

4.2026

3.9686

3.7443

-1.65

1.59

50

4.0588

3.8287

3.6084

-1.70

1.62

18

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

51

3.9206

3.6943

3.4780

-1.74

1.66

52

3.7878

3.5654

3.3531

-1.78

1.70

53

3.6601

3.4416

3.2332

-1.82

1.74

54

3.5374

3.3227

3.1183

-1.87

1.78

55

3.4195

3.2085

3.0079

-1.91

1.82

56

3.3060

3.0989

2.9021

-1.95

1.85

57

3.1969

2.9935

2.8005

-2.00

1.89

58

3.0919

2.8922

2.7029

-2.04

1.93

59

2.9909

2.7948

2.6092

-2.08

1.97

60

2.8936

2.7012

2.5193

-2.13

2.01

61

2.8000

2.6112

2.4328

-2.17

2.05

62

2.7099

2.5246

2.3498

-2.22

2.09

63

2.6232

2.4413

2.2700

-2.26

2.13

64

2.5396

2.3611

2.1932

-2.31

2.17

65

2.4591

2.2840

2.1195

-2.36

2.21

66

2.3815

2.2098

2.0486

-2.40

2.25

67

2.3068

2.1383

1.9803

-2.45

2.29

68

2.2347

2.0695

1.9147

-2.49

2.34

69

2.1652

2.0032

1.8516

-2.54

2.38

70

2.0983

1.9393

1.7908

-2.59

2.42

71

2.0337

1.8778

1.7324

-2.63

2.46

72

1.9714

1.8186

1.6761

-2.68

2.50

73

1.9113

1.7614

1.6219

-2.73

2.54

74

1.8533

1.7064

1.5697

-2.78

2.58

75

1.7974

1.6533

1.5194

-2.83

2.63

76

1.7434

1.6021

1.4710

-2.88

2.67

77

1.6913

1.5528

1.4243

-2.92

2.71

78

1.6409

1.5051

1.3794

-2.97

2.75

79

1.5923

1.4592

1.3360

-3.02

2.80

80

1.5454

1.4149

1.2942

-3.07

2.84

81

1.5000

1.3721

1.2540

-3.12

2.88

82

1.4562

1.3308

1.2151

-3.17

2.93

83

1.4139

1.2910

1.1776

-3.22

2.97

84

1.3730

1.2525

1.1415

-3.27

3.01

85

1.3335

1.2153

1.1066

-3.32

3.06

86

1.2953

1.1794

1.0730

-3.38

3.10

87

1.2583

1.1448

1.0405

-3.43

3.15

88

1.2226

1.1113

1.0092

-3.48

3.19

89

1.1880

1.0789

0.9789

-3.53

3.24

90

1.1546

1.0476

0.9497

-3.58

3.28

91

1.1223

1.0174

0.9215

-3.64

3.33

92

1.0910

0.9882

0.8942

-3.69

3.37

93

1.0607

0.9599

0.8679

-3.74

3.42

19

DomesticAirConditioner

YSCC18FSAADG

Functions and Control

94

1.0314

0.9326

0.8424

-3.80

3.46

95

1.0030

0.9061

0.8179

-3.85

3.51

96

0.9756

0.8806

0.7941

-3.90

3.55

97

0.9490

0.8558

0.7711

-3.96

3.60

98

0.9232

0.8319

0.7489

-4.01

3.64

99

0.8983

0.8088

0.7275

-4.07

3.69

100

0.8741

0.7863

0.7067

-4.12

3.74

101

0.8507

0.7646

0.6867

-4.18

3.78

102

0.8281

0.7436

0.6672

-4.23

3.83

103

0.8061

0.7233

0.6484

-4.29

3.88

104

0.7848

0.7036

0.6303

-4.34

3.92

105

0.7641

0.6845

0.6127

-4.40

3.97

106

0.7441

0.6661

0.5957

-4.46

4.02

107

0.7247

0.6482

0.5792

-4.51

4.07

108

0.7059

0.6308

0.5632

-4.57

4.12

109

0.6877

0.6140

0.5478

-4.63

4.16

110

0.6700

0.5977

0.5328

-4.69

4.21

111

0.6528

0.5820

0.5183

-4.74

4.26

112

0.6361

0.5667

0.5043

-4.80

4.31

113

0.6200

0.5518

0.4907

-4.86

4.36

114

0.6043

0.5374

0.4775

-4.92

4.41

115

0.5891

0.5235

0.4648

-4.98

4.45

116

0.5743

0.5100

0.4524

-5.04

4.50

117

0.5600

0.4968

0.4404

-5.10

4.55

118

0.5460

0.4841

0.4288

-5.16

4.60

119

0.5325

0.4717

0.4175

-5.22

4.65

120

0.5194

0.4597

0.4066

-5.28

4.70

20

DomesticAirConditioner

YSCC18FSAADG

System Configuration

6. System Configuration
6.1 System Configuration
After the installation and test operation of the room air conditioner have been completed, it should be operated and
handled as described below. Every user would like to know the correct method of operation of the room air
conditioner, to check if it is capable of cooling (or heating) well, and to know a clever method of using it.In order to
meet this expectation of the users, giving sufficient explanations taking enough time can be said to reduce about
80% of the requests for servicing. However good the installation work is and however good the functions are, the
customer may blame either the room air conditioner or its installation work because of improper handling. The
installation work and handing over of the unit can only be considered to have been completed when its handling has
been explained to the user without using technical terms but giving full knowledge of the equipment.

21

Domestic Air Conditioner

YSCC18FSAADG

System Configuration

6.2 Instructions
Parts and Functions
1
2
3
45
6
5

7
8

POWER/SOFT button is not available for 07k09k12k.

22

Domestic Air Conditioner

YSCC18FSAADG

Operations

System Configuration

Emergency operation and test operation

Base Operation

Emergency Operation:

Pi

Use this operation only when the remote controller

is defective or lost.
When the emergency operation switch is
pressed,the" Pi "sound is heard once, which
means the start of this operation.
In this operation, the system automatically selects
the operation modes,cooling or fan or heat,
according to the room. temperature.
Room
Operation Designated Timer
Air flow
temperature mode
temperature mode

Remote controller
SPEED

ABOVE 23OC

COOLING

26OC

NO

AUTOMATIC

BELOW 23 C

HEAT

23 C

NO

AUTOMATIC

(Cooling only uint Operation Designated Timer

Air flow
Room temperature
mode temperature mode
O
O
FAN
AUTOMATIC
BELOW 23 C
NO
26 C

1. Unit start

It is not possible to operate in dry mode.

Press ON/OFF on the remote controller, unit starts.

2.Select operation mode

Press MODE button. For each press, operation mode
changes as follows:
Remote controller:

Test operation:
Test operation switch is the same as emergency switch.
Use this switch in the test operation when the room
o

AUTO

COOL

DRY

FAN

temperature is below 16 C, do not use it in the

normal operation.

HEAT

Continue to press the test operation

switch for more than 5 seconds . After
you hear the "Pi" sound twice, release
your finger from the switch: the cooling

3.Select temp.setting
Press TEMP+  TEMP- button
time the button is pressed, temp.setting
increase 1oC,if kept depressed, it will increase
rapidly
TEMP- Every time the button is pressed, temp.setting
decrease 1oC,if kept depressed, it will decrease
rapidly
Select a desired temperature.

TEMP+ Every

4.Fan speed selection

Press FAN SPEED button. For each press, fan speed
changes as follows:
Remote controller:
LOW

MED

AUTO

HI

operation starts with the air flow speed "Hi".

Air Flow Direction Adjustment

1.Status display of air flow
Vertical flap
Pos.1

Pos.2

Pos.3

Pos.4

Pos.5

(Auto swing)

2.Left and right air flow adjustment(manual)

Move the vertical blade by a knob on air conditioner
to adjust left and right direction referring to Fig.

Air conditioner is running under displayed fan speed.

When FAN is set to AUTO, the air conditioner
automatically adjusts the fan speed according to room
temperature.
Operation Remote Display
Controller Board
Mode

Note

AUTO

Under the mode of auto operation, air conditioner will

automatically select Cool or Heat operation according
to room temperature. When FAN is set to AUTO, the
air conditioner automatically adjusts the fan speed

COOL

according to room temperature.

DRY

In DRY mode, when room temperature becomes

lower than temp.setting+2 oC,unit will run intermittently
at LOW speed regardless of FAN setting.

FAN

In FAN operation mode, the unit will not operate in

COOL or HEAT mode but only in FAN mode ,AUTO is
not available in FAN mode.And temp.setting is disabled.
In FAN mode,SLEEP operation is not available.

HEAT

Pi Pi

Remote controller can memorize each operation status. When starting it

next time,just press ON/OFF button and unit will run in previous status.

Cautions:
When adjusting the flap by hand,turn off the unit.
When humidity is high,condensate water might occur
at air outlet if all vertical louvers are adjusted to left or
right.
It is advisable not to keep horizontal flap at downward
position for a long time in COOLor DRY mode ,
otherwise, condensate water might occur.
Note:
When restart after remote turning off, the remote
controller will automatically memorize the previous
set swing position.
23

Domestic Air Conditioner

YSCC18FSAADG

System Configuration

Operation
Sleep Operation

3. In AUTO mode
The unit operaters in corresponding sleep mode
adapted to the automatically selected operation
mode.

Before going to bed,you can simply press the SLEEP

button and unit will operate in SLEEP mode and bring
you a sound sleep.

4. In FAN mode
It has no SLEEP function.

5.Set the wind speed change when sleeping

If the wind speed is high or middle before
setting for the sleep, set for lowing the wind
speed after sleeping.
If it is low wind, no change.

Note
When TIMER function is set, the sleeping function
can't be set up .After the sleeping function is set up ,
if user resets TIMER function, the sleeping function
will be cancelled;the machine will be in the state of
timing-on.

Use of SLEEP function

After the unit starts,set the operation status,
then press SLEEP button before which the
clock must be adjusted and time being set.

Operation Mode
1. In COOL,DRY mode

POWER/SOFT Operation

1 hours after SLEEP mode starts,temp.will become

1OC higher than temp.setting.After another 1 hours,
temp.rises by 1OC futher.The unit will run for further
6 hours then stops Temp. is higher than temp.
setting so that room temperature wont be too low
for your sleep.
SLEEP operation starts

1 hr

(1) POWER Operation

When you need rapid heating or cooling, you can use this
function. In COOL mode, fan speed automatically takes

high speed of AUTO fan mode. In HEAT mode, fan speed

automatically takes medial speed of AUTO fan mode.
(2) SOFT Operation

You can use this function when silence is needed for

rest or reading. In SOFT operation mode, fan speed

SLEEP operation stops

Approx.6hrs

automatically takes low speed of AUTO fan mode.

Rises 1OC

Note
During POWER operation, in rapid HEAT or COOL
mode , the room will show inhomogeneous temperature
distribution. Long period SOFT operation will cause
effect of not too cool or not too warm.

Rises 1OC

1 hr

Temp.setting

Unit stop

In COOL, DRY mode

To cancel POWER or SOFT operation

Press POWER/SOFT button again ,POWER or SOFT
disappears.

2. In HEAT mode
1 hours after SLEEP mode starts,temp will
become 2 OC lower than temp.setting.After
another 1 hours,temp decrease by 2 OC
futher.After more another 3hours,temp.rises
by 1OC futher.The unit will run for further 3
hours then stops.Temp.is lower than temp.
setting so that room temperature wont be
too high for your sleep.
Temp.setting
1 hr

NOTE:
Cooling only unit do not have displays and functions
related with heating.

Unit stop

Decreases 2OC
1 hr

Decreases 2OC
3 hrs
3 hrs

SLEEP
operation starts

Rises 1OC

SLEEP
operation stops

In HEAT mode
24

Domestic Air Conditioner

System Configuration

YSCC18FSAADG

Operation
Timer On/Off On-Off Operation

Healthy airflow Operation

1.After unit starts, select your desired operation mode.

1.Press

2.Press TIMER button to change TIMER mode. Every

time the button is pressed, display changes as follows:

Setting the comfort work conditions.

Remote controller:
BLANK
0.5h

0.5h

0.5h

TIMER ON TIMER OFF

TIMER ON-OFF

0.5h
TIMER OFF-ON

Then select your desired TIMER mode (TIMER ON or

TIMER OFF or TIMER ON-OFF). "
"or "
"will flash.
3.Press

to starting

2.The setting of healthy airflow function

Press
button to enter additional options,Press this
button continuously, the louvers location will cycle between
in the following three locations, to choose the swing location
what you needed,and then press
Healthy
airflow
upwarder

button to set time.

Press the button for each time, setting time in the first
12 hours increased by 0.5 hour every time, after 12
hours,increased by 1 hour every time.
Press the button for each time, settiing time in the first
12 hours decreased by 0.5 hour every time, after 12
hours,decreased by 1 hour every time.
It can be adjusted within 24 hours.
4.Confirm timer setting

Healthy
airflow
downwarder

button to confirm.
Present
position

3.The cancel of the healthy airflow function

Press

button to enter additional options,Press this

button continuously, the louvers location will cycle between

in the following three locations again,and then press
button to cancel.

Notice: Do not direct the flap by hand. Otherwise, the

grille will run incorrectly. If the grille is not run correctly, stop

After adjust the time,press

button and confirm the
time ON or OFF button will not flash any more.

for a minute and then start, adjusting by remote

5.Cancel timer setting

Press the timer button by times until the time display
eliminated.

Note:

Hints:
After replacing batteries or a power failure happens, time
setting should be reset.
According to the Time setting sequence of TIMER ON or
TIMER OFF, either Start-Stop or Stop-Start can be achieved.

2.In cooling, it is better to select the

controller.

1.After setting the healthy airflow function, the position

grill is fixed.
mode.

3.In cooling and dry, using the air conditioner for a long
time under the high air humidity, condensate water may
occur at the grille .

25

Domestic Air Conditioner

System Configuration

YSCC18FSAADG

Maintenance
For Smart Use of The Air Conditioner
Setting of proper room
temperature

Remote Controller

Do not block the air inlet

or outlet

Indoor Body

Proper
temperature

wipe the air conditioner by using a

soft and dry cloth.For serious stains,
use a neutral detergent diluted with
water.Wring the water out of the
cloth before wiping,then wipe off the
detergent completely.

Do not usewater,wipe the controller

with a dry cloth.Do not use glass
cleaner or chemical cloth.

Do not use the following for cleaning

Use the timer effectively

Close doors and windows

during operation

Gasoline,benzine, thinner or cleanser

may damage the coating of the unit.

Hot water over 40 O C(104O F) may

cause discoloring or deformation.

Air Filter cleaning

During cooling operation

prevent the penetration
of direct sunlight with
curtain or blind

Open the inlet grille by pulling it upward.

Remove the filter.
Push up the filter's center tab slightly until it is
released from the stopper, and remove the filter downward.

Clean the filter.

Use the louvers effectively

If the unit is not to be used

for a long time, turn off the
power supply main switch.

Use a vacuum cleaner to remove dust, or wash the filter with

water.After washing, dry the filter completely in the shade.

Attach the filter.

Attach the filter correctly so that the "FRONT" indication
is facing to the front.Make sure that the filter is
completely fixed behind the stopper.If the right
and left filters are not attached correctly, that
may cause defects.

OFF

Once every
two weeks

Close the inlet grille.

Replacement of Air Purifying Filter

1.Open the lnlet Grille

4.Attach the standard air filter

Prop up the inlet grille by with a grille

support located in the right side of
the indoor unit.

(Necessary installation)

ATTENTION:
The white side of the photocatalyst air purifying filter
face outside,and the black side face the unit The green
side of the bacteria-killing medium air purifying filter face
outside,and the white side face the unit.

2.Detach the standard air filter

Slide the knob slightly upward to
release the filter, then withdraw it.

5.Close the Inlet Grille

Close the Grille surely

NOTE:

Detach old Air Purifying Filter

The photocatalyst air purifying filter will be solarized in fixed

time. In normal family, it will be solarized every 6 months.
The bacteria-killing medium air purifying filter will be used
for a long time,no need for replacement. But in the period
of using them ,you should remove the dust frequently by
using vacuum cleaner or flaping them lightly,otherwise ,
its performance will be affected.

3.Attach Air Purifying Filter

Put air purifying filter appliances into the
right and left filter frames.

Please keep the bacteria-killing medium air purifying filter in

the cool and dry conditions avoid long time directly sunshine
when you stop using it,or its ability of sterilization will be
reduced.

26

Domestic Air Conditioner

System Configuration

YSCC18FSAADG

Cautions
WARNING
This system should be installed by a qualified HVAC professional.
Do not attempt to install the air conditioner by yourself because improper works
may cause fire, water leakage, personal injury or cleath.

WARNING
When abnormality such as burnt-small found,
immediately stop the operation button and
contact sales shop.

Check proper
installation of the
drainage securely

Use an exclusive
power source
with a circuit
breaker

STRICT
ENFORCEMENT

OFF
Connect power supply cord
to the outlet completely

STRICT
ENFORCEMENT

Use the proper voltage

STRICT
STRICT
ENFORCEMENT
ENFORCEMENT
Take care not to damage
Do not use power supply
the power supply cord.
cord in a bundle.

PROHIBITION

PROHIBITION

PROHIBITION

Do not start or stop the

operation by disconnecting
the power supply cord
and so on.

1.Do not use power supply cord extended

or connected in halfway
2.Do not install in the place where there is any
possibility of inflammable gas leakage around the unit.
3.Do not get the unit exposed
to vapor or oil steam.
PROHIBITION
Do not insert objects into the air
inlet or outlet.

Do not channel the air flow directly

at people, especially at infants or
the aged.

PROHIBITION

Do not try to repair or

reconstruct by yourself.

Connect the earth

cable.

earthing

PROHIBITION

CAUTION
Do not use for the purpose of storage of
food, art work, precise equipment,
breeding, or cultivation.

PROHIBITION
Do not install the unit near a fireplace
or other heating apparatus.

Take fresh air occasionally especially

when gas appliance is running at the
same time.

STRICT
ENFORCEMENT
Check good condition of the
installation stand

PROHIBITION
Do not place animals or plants in
the direct path of the air flow

Do not operate the switch with

wet hand.

PROHIBITION
Do not pour water onto the unit
for cleaning

PROHIBITION

PROHIBITION
Do not place any objects on or
climb on the unit.

PROHIBITION

PROHIBITION

27

Do not place flower vase or water

containers on the top of the unit.

PROHIBITION

Domestic Air Conditioner

System Configuration

YSCC18FSAADG

Trouble shooting

Cautions

Before asking for service, check the following

first.
Phenomenon
The system
does not restart
immediately.

Noise is heard

Normal
Performance
inspection

Smells are
generated.
Mist or steam are
blown out.

Cause or check points

When unit is stopped, it won't restart
immediately until 3 minutes have
elapsed to protect the system.
When the electric plug is pulled out
and reinserted, the protection circuit
will work for 3 minutes to protect the
air conditioner.
During unit operation or at stop,
a swishing or gurgling noise may
be heard.At first 2-3 minutes after
unit start, this noise is more noticeable.
(This noise is generated by
refrigerant flowing in the system.)
During unit operation, a cracking
noise may be heard.This noise is
generated by the casing expanding
or shrinking because of
temperature changes.
Should there be a big noise from
air flow in unit operation, air
filter may be too dirty.
This is because the system
circulates smells from the interior
air such as the smell of furniture,
paint, cigarettes.
During COOL or DRY operation,
indoor unit may blow out mist.
This is due to the sudden cooling
of indoor air.

Do not obstruct or cover the ventilation grille of the air

conditoner.Do not put fingers or any other things into the
inlet/outlet and swing louver.
Do not allow children to play with the air conditioner.In no
case should children be allowed to sit on the outdoor unit.

Specifications
The refrigerating circuit is a sealed system.

The machine is adaptive in following situation

1.Applicable ambient temperature range:

Indoor
Cooling
Outdoor

Maximum:D.B/W.B 32oC/23oC ( 89.6oF/73.4 oF )

Minimum:D.B/W.B 19.4oC/13.9oC ( 67 oF/57 oF )
o
o
Maximum:D.B/W.B 46.1oC/23.9oC ( 115 F/75 F )
o
o
o
o
Minimum:D.B/W.B 19.4 C/11.9 C ( 67 F/57 F )

2. If the power supply cord is damaged, it must be replaced by the

manufacturer or its service agent or a similar qualified person.
3.If the fuse of indoor unit on PC board is broken,please change
it with the type of T. 3.15A/ 250V. If the fuse of outdoor unit is
broken,change it with the type of T.25A/250V
4. The wiring method should be in line with the local wiring standard.
5. After installation, the power plug should be easily reached.

In dry mode, fan

speed cant be
changed.

Multiple
check

Poor cooling

In DRY mode, when room temperature

becomes lower than temp.
setting+2 oC,unit will run
intermittently at LOW speed
regardless of FAN setting.

6. The waste battery should be disposed properly.

Is power plug inserted?

Is there a power failure?
Is fuse blownout?

8. Young children should be supervised to ensure that they do not play

Is the air filter dirty?

Normally it should be cleaned
every 15 days.
Are there any obstacles before
inlet and outlet?
Is temperature set correctly?
Are there some doors or
windows left open?
Is there any direct sunlight
through the window during the
cooling operation?(Use curtain)
Are there too much heat sources
or too many people in the room
during cooling operation?

9. Please employ the proper power plug, which fit into the power supply
cord.

7. The appliance is not intended for use by young children or infirm

persons without supervision.

with the appliance.

10. The power plug and connecting cable must have acquired the local
attestation.
11.In order to protect the units,please turn off the A/C first, and at least
30 seconds later, cutting off the power.

28

Domestic Air Conditioner

YSCC18FSAADG

Codes and Description

7. Codes and Description

7.1. Problem Symptoms and Measures
Symptom
None of the
units operates

Check Item
Check the power supply.
Check the indoor PCB

Details of Measure
Check to make sure that the rated voltage is
supplied.
Check to make sure that the indoor PCB is
broken

Equipment
operates but Diagnosis by service
does not cool, port
pressure
and Check for insufficient gas.
or does not operating
current.
heat (only for
heat pump)
Large
to make sure that the required spaces
operating
Check the installation Check
for installation (specified in the Technical Guide,
noise
and condition.
etc.) are provided.
vibrations

7.2 Error Codes and Description indoor display

Code indication

Description

indoor

Indoor Malfunction

E1

Room temperature sensor failure

E2

Heat-exchange sensor failure

E4

Indoor EEPROM error

E14

Indoor fan motor malfunction

The code indication that is listed above is the main fault

Trouble shooting
Caution
Be sure to turn off power switch before connect or disconnect connector, or else parts damage may be
occurred.

E1: Room temperature sensor failure

E2: Heat-exchange sensor failure

CN1
CN1

29

DomesticAirConditioner

Codes and Description

YSCC18FSAADG

whether terminal CN1

on

NO

Pull out the terminals on the indoor mainboard and

indoor PCB contact well?

reinsert them

YES

Pull the sensor out of the mainboard

1)

Measure the value of resistance Between its two

jumpers

2)

Measure the temperature at the room temperature

sensing head.

Check the value of the

YES
Sensor is broken, replace it with new sensor

sensor to see whether the

sensor is damaged or not?

NO

The indoor PCB is broken, replace with new indoor PCB

E4 Indoor EEPROM error:

Replace the PCB of indoor unit

E14: Indoor fan motor malfunction

Notes: When the unit is on, dont pull out or insert the terminal of the motor (CN26), or else the motor
would be damaged.

30

DomesticAirConditioner

YSCC18FSAADG

Code and Description

Turn off power supply and

rotate fan by hand

Does fan rotate

NO
Replace fan motor

smoothly?

Yes
Turn power ON and operate fan

No
Does it rotate?

Turn off power supply and disconnect fan

motor connector, then turn power ON

Check output of fan motor connector

Yes
Is motor power voltage

NO

DC310V generated?

Replace indoor
unit PCB

Yes
Stop fan motor
Is motor control power

NO

voltageDC15Vgenerat

Replace indoor
unit PCB

Yes

Is rotation number
Is rotation number

command voltage

command pulse

DC1 6V generated?

Yes
Replace fan
motor

generated?

No
Yes
No
Replace indoor fan motor

Replace indoor unit PCB

31

DomesticAirConditioner

Capacity

YSCC18FSAADG

8.1 Cooling Capacity-temperature Curves

YSCC18FSAADG cooling value-temperature table

cooling temp.(humidity)40%

indoor temp
67

72

77

82

87

95

105

115

67/50

16740 16380 15840 15300 14760 14040 12960 11340

67/57

18000 17640 17280 16740 16020 15300 14220 12960

67/62

19440 19080 18540 17820 17280 16740 15660 14400

72/57

17820 17640 17280 16740 16020 15300 14220 12960

72/62

19440 19080 18540 17820 17280 16740 15660 14400

80/62

19440 19080 18540 17820 17280 16740 15660 14400

80/67

21060 20700 20160 19620 18720 18000 17100 16020

80/72

22140 21780 21240 20700 19980 19260 18540 17280

87/72

22140 21780 21240 20700 19980 19260 18540 17280

32

DomesticAirConditioner

Capacity

YSCC18FSAADG

8.2 Cooling Power Consumption Value-temperature Curves

YSCC18FSAADG Performance Curves

Power Consumption Value-temperature Curves

indoor temp
DB/WB

cooling temp.(humidity)40%
67

72

77

82

87

95

105

115

67/50

1120 1168 1216 1280 1328

1376

1472

1536

67/57

1152 1216 1280 1344 1376

1440

1520

1680

67/62

1216 1264 1328 1408 1472

1480

1536

1760

72/57

1152 1216 1280 1344 1392

1440

1520

1680

72/62

1216 1264 1328 1392 1472

1536

1640

1760

80/62

1216 1264 1328 1392 1472

1536

1640

1760

80/67

1280 1328 1376 1440 1520

1600

1712

1808

80/72

1328 1392 1456 1520 1600

1680

1824

1936

87/72

1328 1392 1456 1520 1600

1680

1824

1936

33

Domestic Air Conditioner

YSCC18FSAADG

Installations

9. Installation
Preparation
Selection of Installation Place

Necessary Tools for Installation

Indoor Unit - Select a plocation that is

Torque wrench
(17mm,22mm,26mm)
Pipe cutter
Flaring tool
Knife
Measuring tape
Reamer

Hammer
Nipper
Hacksaw
Hole core drill
Spanner(17,19 and 26mm)
Gas leakage detector or
soap-and-water solution

Robust not causing vibration, where the body can be supported sXIFLHQWO\
Not affected by heat or steam generated in the vicinity, where inlet and outlet of the
unit are not disturbed.
Possible to drain easily, where piping can be connected with the outdoor unit.
Where cold air can be spread in a room evenly.
Nearby a power receptacle. (Refer to drawings).
Place where the distance of more than lm from televisions, radios, wireless apparatuses
and uorescent lamps can be left.
In the case of xing the remote controller on a wall, place where the indoor unit can
receive signals when the uorescent lamps in the room are in use.

Power Source
Before inserting power plug into receptacle, check the voltage without fail.
The power source is the same as the corresponding name plate.
Install an exclusive branch circuit of the power.
A receptacle shall be set up in a distance where the power cable can be
reached.Do not extend the cable by cutting it.

Outdoor Unit - Select a plocation that is

1RWOHVVDIIHFWHGE\UDLQRUGLUHFWVXQOLJKWDQGLVVXIFLHQWO\ ventilated.
Strong enough to bear the unit, where vibration and noise are not increased.
Place, where discharged wind and noise do not cause a nuisance to the neighbors.
Place, where a distance marked
is available as illustrated in the above gure.

Drawing for the installation of indoor and outdoor units

The models adopt HC FC free refrigerant R410A

Attention must be paid to

the pitch of drain hose

Optional parts for piping

more than 10cm

(3 7/8)

A Non-adhesive tape
B Adhesive tape
C Saddle (L.S) with screws
Connecting electric cable
D
for indoor and outdoor
E Drain hose
F Heating insulating material

more than 10cm

(3 7/8)

G Piping hole cover

Arrangement of piping
directions

Floor xing dimensions of the

more than 10cm

(3 7/8)

outdoor unit (Unit:mm / inch)

For:HSU18VCK-W

Rear
right

Left

340
(13 1/2)

Rear left

113.5
(4 1/2)

Right

633
(24 7/8)

113.5
(4 1/2)

For:HSU24VCK-W

more than 15cm

(5 7/8)

184
(7 1/4)

more than 20cm

(7 7/8)

3 80
(14 15/16)

Below

580
(22 7/8)

184
(7 1/4)

Fixing of outdoor unit

The marks from A to

G in the gure are the
parts numbers.
The distance between
the indoor unit and the
oor should be more
than 2m.

Fix the unit to concrete or block

with bolts (10mm) and nuts rmly
and horizontally.
When tting the unit to wall
surface, roof or rooftop, x
a supporter surely with nails
or wires in consideration of
earthquake and strong wind.
If vibration may affect the

more than 60cm

(23 5/8)

more than 25cm

(9 7/8)

house, x the unit by attaching a

vibration-proof mat.

Please be subject to the actual product purchased , the above picture is just for your reference.
Read this manual before installation
Explain suf ciently the operating means to the user according to this manual.
NO.0010536243

34

Domestic air conditioner

Installations

YSCC18FSAADG

1. Insert the drain hose into the dent of heat insulation materials of indoor unit.
2. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it
out on the front side, then connect them.
3. Coat the aring seal face with refrigerant oil and connect pipes.
Cover the connection part with heat insulation materials, cover with adhesive tape.

Accessory parts
Remote controller (1)

Drain hose (1)

R-03 dry battery (2)

Cushion (4)

Mounting plate (1)

Drain-elbow (1)

Indoor/outdoor electric cable

Heat insulation
material

Plastic cap (4)

4X25 Screw (4)

Piping

Lid for right

piping

Pipe supporting plate (1)

Lid for left piping

Pipe supporting
plate

Drain hose

Lid for under piping pipe

Selection of pipe
For 18K

Type
Liquid pipe ()
Gas pipe ()
NOTE

Fix with adhesive tape

6.35mm(1/4)

Indoor/outdoor electric cable and drain hose must be bound with refrigerant
piping with protecting tape.

For 24K

[ Other direction piping ]

9.52mm(3/8)

Cut away, with a nipper, the lid for piping according to the piping direction and
then bend the pipe according to the position of wall hole. When bending, be
careful not to crash pipes.
Connect beforehand the indoor/outdoor electric cable, and then pull out the
connected to the heat insulation of connecting part specially.

12.7mm(1/2) 15.88mm(5/8)

The thickness of the pipe must be 0.8mm(1/16) at least.

Indoor unit
1

Fitting of the Mounting Plate and Positioning of the wall Hole

Fixing the indoor unit body

When the mounting plate is rst xed

Hang the unit body securely onto the upper notches of the
mounting plate. Move the body from side to side to verify
LWVVHFXUH[LQJ
In order to x the body onto the mounting plate,hold up
the body aslant from the underside and then put it down
perpendicularly.

1. Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate
to be xed against the wall, then temporarily fasten the plate with one steel nail.
2. Make sure once more the proper level of the plate, by hanging a thread with a
weight from the central top of the plate, then fasten securely the plate with the
attachment steel nail.
3. Find the wall hole location A using a measuring tape

mounting plate

mm

(3 9/16)

Unloading of indoor unit body

A=150mm

When you unload the indoor unit, please use

your hand to raise the body, then lift the
bottom of the body outward slightly
and lift the unit until it leaves the
mounting plate.

mm

(5 7/8)

(2 3/4)

mounting plate

Connecting the indoor/outdoor Electric Cable

(5 7/8)

35mm
(5 7/8)

mm
A=150mm

(2 3/4)

Removing the wiring cover

When the mounting plate is xed side bar and lintel

Remove terminal cover at right bottom corner of indoor unit, then take

off wiring cover by removing its screws.

Fix to side bar and lintel a mounting bar, Which is separately sold, and then
fasten the plate to the xed mounting bar.
Refer to the previous article, When the mounting plate is Ust xed , for the
position of wall hole.

When connecting the cable after installing the indoor unit

Making a Hole on the Wall and Fitting the Piping Hole Cover
1. Insert from outside the room cable into left side of the wall

Make a hole of 70 mm(2 3/4)in diameter, slightly descending to outside the wall.
Install piping hole cover and seal it off with putty after installation

hole, in which the pipe has already existed.

2. Pull out the cable on the front side, and connect the cable
making a loop.

Wall hole

Pitch downward for drainage

When connecting the cable before installing the indoor unit

70mm
(2 3/4)

Indoor side

Outdoor side
Thickness of wall

Insert the cord from the back side of the unit, then pull it out on the front side.
Fasten the unit wire harness to the conduit holder using the lock nut.
Position the conduit holder to its original state using screw.

Installation of the Indoor Unit

Drawing of pipe

[ Rear piping ]
Draw pipes and the drain hose, then fasten them with the adhesive tape

Conduit holder

Cut the 6 slit sear

[ Left Left-rear piping ]

In case of left side piping, cut away, with a nipper, the lid for left piping.
In case of left-rear piping, bend the pipes according to the piping direction to
the mark of hole for left-rear piping which is marked on heat insulation materials.

Note

35

When connecting the cable, conrm the terminal number of indoor and
outdoor units carefully. If wiring is not correct, proper operation can not
be carried out and will cause damage to the units.

Domestic air conditioner

Installations

YSCC18FSAADG
Ensure that on dirt or debris enters the pipe.

The standard pipe length is 7m(27 9/16)

. If it is over 7m(27 9/16), the function of
the unit will be affected. If the pipe has to be lengthened, the refrigerant should
be charged, according to 50 g /m(0.045oz/inch). But the charge of refrigerant must
be conducted by professional air conditioner servicer. Before adding additional
perform air purging from the refrigerant pipes and indoor unit using a vacuum
refrigerant, pump,then charge additional refrigerant.

CAUTION
Outdoor unit
Indoor unit

A
A

Indoor unit

Outdoor unit

Outdoor unit

YSCC18FSAADG Power cable:

YSCC18FSAADG Power cable:

Oil trap
Indoor unit

Max.Elevation: Amax=15 m
In case the elevation A is more
than 5m, oil trap shoud be
installed every 5~7m

Max. Length: Bmax=25m

In case the pipe length B is
more than 10m, the refrigerant
should be charged, according
to 50 g/m.

2wire with ground 12AWG

2wire with ground 12AWG

Connection

Take off the panel(top), by removing the 5 screws.

1. If the fuse on PC board is broken please change it with the type of

Remove the plugs on the conduit plate.

T. 3.15A/250V (indoor unit), 25A/250V(outdoor unit).

Temporarily mount the conduit tubes on the conduit plate.

2. The wiring method should be in line with the local wiring standard.
3. After installation, the power plug should be easily reached.

Connect both the power supply and unit wire harness to

4. A breaker should be incorporated into xed wiring. The breaker should be

all-pole switch.

Ground the unit in accordance with local codes.

the corresponding terminals on the terminal board.

Allow several extra inches of wire for making wiring

connections.
Use lock nuts to secure conduit tubes.

Outdoor unit
1

Installation of Outdoor Unit

Attaching Drain-Elbow

Install according to

Drawing for the installation of indoor and outdoor units

Connection of pipes

To bend a pipe, be careful not to crush the pipe,

1.

and the bending radius should be 30(1 1/6) to 40 mm(1 4/7) or longer.

Connecting the pipe of gas side rst makes working easier.

The connection pipe is specialized for R410A.
Half union

Flare nut

If the drain-elbow is used,

please attach it as gure. (Note:
Only for heat pump unit.)

Purging Method:To use vacuum pump

Detach the service ports cap of 3-way valve, the valve rods cap for 2-way valve
and 3-ways, connect the service port into the projection of charge hose (Iow)
for gaugemanifold. Then connect the projection of charge hose (center) for gaugemanifold into vacuum pump.

2. Open the handle at Iow in

gaugemanifold, operate vacuum pump. If the scalemoves of gause (Iow) reach vacuum condition in a moment, check 1. again.

Forced fastening without careful centering may

damage the threads and cause a leakage of gas.

3. Vacuum for over 15min. And check the gauge which should read -0.1MPa

Spanner

Torque wrench

Pipe Diameter()

Fastening torque

Liquid side6.35mm(1/4")

18N.m

Liquid/Gas side9.52mm(3/8")

42 N.m

Gas side 12.7mm(1/2")

55N.m

Gas side 15.88mm(5/8")

60 N.m

(76 cm Hg) at Iow pressure side. After the completion of vacuuming, close the
handle Lo in gaugemanifold and stop the operation of the vacuum pump. Check
condition of the scale and hold it for 1-2min. If the scale-moves back in spite of
tightening, make aring work again, the return to the beginning of 3 .

4. Open the valve rod for the 2-way valve counterclockwise to 90 degrees.
After 6 seconds, close the 2-way valve and make the inspection of gas leakage.

36

Domestic air conditioner

Installations

YSCC18FSAADG
5. No gas leakage?

On Drainage

In case of gas leakage, tighten parts of pipe connection. If leakage stops,

then proceed step 6. If leak continues, remove the refrigerant used for the
leakage check and flare tubes again. Repeat vacuum and leak and if no
leakage, proceed to step 6.

Please install the drain hose so as to be downward slope without fail.

Please dont do the drainage as shown below.

6. Detach the charge hose from the service port, open 2-way valve and 3-way. Turn

Less than
5cm

the valve rod counterclockwise.

leakage, turn the service ports cap, the valve rods cap for 2-way
valve and 3-ways a little more than the point where the torque increases suddenly.

7.To prevent the gas

8. After attaching the each caps, check the gas

Step 1.

It becomes The end is imm- It waves. The gap with the There is the bad
high midway. ersed in water.
ground is too small smell from a ditch

leakage around the caps.

Please pour water in the drain pan of the indoor unit, and conrm that drainage
is carried out surely to outdoor.
In case that the attached drain hose is in a room, please apply heat insulation to
it without fail.

Step 2.

2-way valve Liquid Side

3-way valve Gas Side

Open

Gaugemanifold(for R410A)
Anti countercurrent joint

Refrigerant charge label

Step 3.

Contains fluorinated greenhouse gases

covered by the Kyoto Protocol

Close
Tube(for R410A)
Step 4.

Vacuum pump(for R410A)

Step 6.

2-way valve

2-way valve
3-way valve

R410A

1=

kg

2=

kg

1+2=

kg

3-way valve
O

Open 90

2-way valve
3-way valve

Step 7.

Valve rod cap

Valve rod cap
Service port cap

CAUTION
If the refrigerant of the air conditioner leaks, it is necessary to discharge all the
refrigerant. Vacuum rst, then charge the liquid refrigerant into air conditioner
according to the amount marked on the name plate.
Please do not let other cooling medium, except specied one (R410A), or air
enter into the cooling circulation system. Otherwise, there will be abnormal
high pressure in the system casuing damage and possibly personal injuries.

Power Source Installation

The power source must be exclusively used for air conditioner. (Over I0A)
In the case of installing an air conditioner in a moist place, please install an earth leakage breaker (GFCI).
For installation in other places, use a circuit breaker as far as possible.

Flare tool for R410A

Conventional are tool

Clutch-type

clutch-type(Rigid-type) Wing-nut type (Imperial-type)

1.Cut pipe

Flare tooling die

3.Insert the are nut

C o r re c t

Please kindly explain to our customers how to operate

through the instruction manual.
Check Items for Test Run

Pipe cutting is carried out with a pipe cutter and burs must be removed.
After inserting the are nut, aring work is carried out.

1.0~1.5mm
3/76 ~1/17 inch

Check for Installation and Test Run

Cutting and Flaring Work of Piping

0~0.5mm
0~1/51 inch

This product contains fluorinated greenhouse gases covered by

the Kyoto Protocol. Do not vent into the atmosphere.
Refrigerant type:R410A
GWP* value:1975
GWP=global warming potential
Please fill in with indelible ink,
1
the factory refrigerant charge of the product
2
the additional refrigerant amount charged in the field and
1+2 the total refrigerant charge
on the refrigerant charge label supplied with the product.
The filled out label must be adhered in the proximity of the product
charging port (e.g. onto the inside of the stop valve cover).
A contains fluorinated greenhouse gases covered by the Kyoto
Protocol
B factory refrigerant charge of the product: see unit name plate
C additional refrigerant amount charged in the field
D total refrigerant charge
E outdoor unit
F refrigerant cylinder and manifold for charging

2-way valve 3-way valve

Put check mark

in boxes

Gas leak from pipe connecting?

Heat insulation of pipe connecting?
Are the connecting wirings of indoor and outdoor rmly
inserted to the terminal block?
Is the connecting wiring of indoor and outdoor rmly xed?
Is drainage securely carried out?
Is the earth line securely connected?
Is the indoor unit securely xed?
Is power source voltage abided by the code?
Is there any noise?
Is the lamp normally lighting?
Are cooling and heating (when in heat pump) performed normally?
Is the operation of room temperature regulator normal?

1.5~2.0mm
1/17 ~1/8 inch
2.Remove burs

4.Flare pipe

I nc o r re c t

Lean

Damage of are Crack

Partial

Too outside

37

Domestic air conditioner

YSCC18FSAADG

Wiring Diagrams

10. Wiring Diagrams

Indoor

Up&down step motor

38

DomesticAirConditioner

YSCC18FSAADG

Wiring Diagrams

1 0 .2 O u td oor

NOTE:

1.The parts are optional.

2.Some types may not have the dotted lines. marked with

39

DomesticAirConditioner

YSCC18FSAADG

Wiring Diagrams

10. 3 CIRCUIT DIAGRAM

1

+5V

IC1

1
2
RST

1
2
3
4

57
54

MODE

P4_5/INT0

RESET

P1_3/KI3/AN11
P3_0/TRAO
P3_1/TRBO
P1_0/KI0/AN8

P0_5/AN2/CLK1
P0_4/AN3

+5V

+5V

R136
C14
4.7K- 1%
0.001UF

B5B-XH-A

58

KZ
KZ
+5V

P0_6/AN1/DA0

ST

1
2

+12V

9
56

+5V

2
1

P6_1

55

P6_2

62
61
10

+5V

VCC/AVCC
VREF
VCC/AVCC

8
59

15

+5V

VSS/AVSS
VSS/AVSS

24
45

+5V

P3_2/(INT2)

26
27

4
3
2
1

p_12

+5V

A
1
2

p_11

A0
A1
A2
GND

VCC
WP
SCL
SDA

RG2
p_11
p_12
p_42
p_43
p_46
p_47

+12V
8
7
6
5
4
3
2
1

38

8
7
6
5
4
3
2
1

+5V
35

GND
A7
A6
A5
A4
A3
A2
A1

GND
A7
A6
A5
A4
A3
A2
A1

+12
B7
B6
B5
B4
B3
B2
B1

9
10
11
12
13
14
15
16

+12
B7
B6
B5
B4
B3
B2
B1

9
10
11
12
13
14
15
16

+12V
10
9
8
7
6
5
4
3
2
1

+12V

+12V

12
13
14
15
11
25
20

P5_3/TRCIOC
P5_2/TRCIOB
P5_1/TRCIOA/TRCTRG
P5_0/TRCCLK
P5_4/TRCIOD
P1_6/CLK0
P2_3/TRDIOD0

P3_4/SDA/SCS

8
7
6
5
4
3
2
1

+12V

GND
A7
A6
A5
A4
A3
A2
A1

9
10
11
12
13
14
15
16

+12
B7
B6
B5
B4
B3
B2
B1

+12V

5
4
3
2
1

+12V

8
7
6
5

4
5

E2
E2

5
4
3
2
1

25

+5V

1
2
3
4

+5V

RG1

22
39
40
50
51
52
53

P1_5/RXD0
P1_4/TXD0

+5V

1
2

44
47
48
19
18
17
16
29
31
32
33
34
37

P2_1/TRDIOB0
P6_5/(CLK1)/CLK2
P6_4/RXD2
P0_0/AN7
P0_1/AN6
P0_2/AN5
P0_3/AN4

P1_7/TRAIO/INT1

E17
4.7uF-16V

p_1

60 GG
64 ST
63

P6_7/INT3/RXD1

8
7
6D
5
4
3
2
1
GG

21
23

P3_6/(INT1)
P1_2/KI2/AN10
P1_1/KI1/AN9
P2_4/TRDIOA1
P2_5/TRDIOB1
P2_6/TRDIOC1
P2_7/TRDIOD1
P8_5/TRFO12
P8_3/TRFO10/TRFI
P8_2/TRFO02
P8_1/TRFO01
P8_0/TRFO00
P6_6/INT2/TXD1

P4_6/XIN

1
2
3
4
5
6
7
8
9
10

28

P0_7/AN0/DA1
P3_5/SCL/SSCK
P3_7/SSO

P4_7/XOUT

OSC1

R135
1K

1
2
3
4
5

TO

+5V

1
41 DIG1
35 DIG2
30 L

P2_2/TRDIOC0
P2_0/TRDIOA0/TRDCLK

E16
4.7uF/16V

CN5

+5V

2
1

46 595-RCK
43 595-SER
42 595-SCK
49

P8_6

1
2

+5V

36

P3_3/SSI
P6_3/TXD2
P6_0/TREO
P8_4/TRFO11

B4B-XH-A

RLS4148
D31

+5V

+5V

P4_3/XCIN
P4_4/XCOUT

R5F212A7SNFA

VCC

1A-800V-500ns-FR106

1N5399

1
2
3
4
C43

0.1uF/50V

RV1
14561*

R6

7
6
5
4
3
2
1

0.1uF
1000uF-35V-105

IC10

0.1uF

470uF-16V

TLP421
VCC
4.7uF-50V-105

B7B-XH- A

ZD3

12V-1W-1N4742A

390

VS

10-1/4W

TLP421

IC4

10K

+5V
1

10K

TLP421
C

47uF-50V-105

1-1/2W

220V-N

FUSE1
T3.15A/250VAC

100K-1/ 4W

18V-1W-1N4746A

ZD1

R9

IC2

15

CN26

R59

1A-800V-500ns-FR106

1
2
3
4

D1

+12V

IC3

OUT

D7

ICE2A265

3A-200V-ER302

+5V

+5V

R10

47K-2W
330 K-2W

0.1uF-275VAC

1N5399

CH1
250 L

IN

D8

D2

LX1

32mH-0.35A-LB2271

10-1/4W

D6

8
7
6
5

220V-L

T1

8
7
6
5

1N5399

1
2
3
4

22u F-25V-105

D4

C44

1.5A-7805

18V-1W-1N4746A

27-1/4 W

1N5399

1A-800V-500ns-FR106
4.7 nF-27 5VAC

100 uF-450V-105

D3
220V-N

BCK-6-FE1901 10uF-25V-105

VCC

HS1
H-25*15
IC6

ZD2

VS

GND

SCK-4R72

4.7 uF-50V-10 5

10-1/4W
1.5K-1/4W

D5

2.2nF/250V

CX1
0.1uF-275VAC

2.2nF/250V

+12V

+12V
1
D25
RLS4148

D20

RLS4148

1
B

D21
D22
D23
RLS4148 RLS4148 RLS4148

D26
RLS4148

p_42

R61

R67 470

p_43
2

4
43

21

p_1
N
ST
WF

21

43

R81

CN54

470

R75 4.7K
R78 470

D24
RLS4148

2K

R77 4.7K

R80

2
D30

RLS4148

1
2
3

+12V

+5V
1

CN49

4.7K

3
2
1

D29
RLS4148

4.7K

D28
RLS4148

R71

R76

p_47

D27
RLS4148

B5B-XH-A

4.7K
R72 470

p_46

1
2
3
4
5

1
2
3

+5V
R104 2K
R106
47K

RG2
C10
0.1uF

1
2
3

R105 2K
R107
47K

C11
0.1uF

RG1

220V-L

40

DomesticAirConditioner

YSCC18FSAADG

Dimensional drawings

10.4 Outdoor Unit

41

Domestic Air Conditioner

Center of Gravity

YSCC18FSAADG

1046

299

195

434.7

234

860

308
159.4

730

330.7

42

Domestic Air Conditioner

YSCC18FSAADG

43

Appendix

Domestic Air Conditioner

YSCC18FSAADG

Appendix

YSCC18FSAADG

44

Domestic Air Conditioner