Chapter #26-Capacitance & Dielectrics

Download as pdf or txt
Download as pdf or txt
You are on page 1of 42

Chapter #26- Capacitance &

Dielectrics

Capacitors
Capacitors are devices that
store electric charge.
Examples of where
capacitors are used include:
radio receivers
filters in power supplies
to eliminate sparking in
automobile ignition systems
energy-storing devices in
electronic flashes

Makeup of a Capacitor
A capacitor consists of two
conductors.
These conductors are called plates.
When the conductor is charged,
the plates carry charges of equal
magnitude and opposite directions.

A potential difference exists


between the plates due to
the charge.

Definition of Capacitance
The capacitance, C, of a capacitor is defined as the ratio of the magnitude
of the charge on either conductor to the potential difference between the
conductors.
Q

The SI unit of capacitance is the farad (F).


The farad is a large unit, typically you will see microfarads (mF) and
picofarads (pF).
Capacitance will always be a positive quantity.
The capacitance of a given capacitor is constant.
The capacitance is a measure of the capacitors ability to store charge .
The capacitance of a capacitor is the amount of charge the capacitor can
store per unit of potential difference.
4

Parallel Plate Capacitor


Each plate is connected to a
terminal of the battery.
The battery is a source of
potential difference.
If the capacitor is initially
uncharged, the battery
establishes an electric field in the
connecting wires.

Parallel Plate Capacitor,

cont..

This field applies a force on electrons in the wire just outside of the plates.
The force causes the electrons to move onto the negative plate.
This continues until equilibrium is achieved.
The plate, the wire and the terminal are all at the same potential.
At this point, there is no field present in the wire and the movement of the
electrons ceases.
The plate is now negatively charged.
A similar process occurs at the other plate, electrons moving away from the
plate and leaving it positively charged.
In its final configuration, the potential difference across the capacitor plates
is the same as that between the terminals of the battery.
6

Capacitance Isolated Sphere


Assume a spherical charged conductor with radius

a.

The sphere will have the same capacitance as it would if there were
a conducting sphere of infinite radius, concentric with the original
sphere.
Assume V = 0 for the infinitely large shell

Q
Q
a

4oa
C
V keQ / a ke
Note, this is independent of the charge on the sphere and its
potential.

Capacitance Parallel Plates


The charge density on the plates is = Q/A.
A is the area of each plate, the area of each plate is equal
Q is the charge on each plate, equal with opposite signs

The electric field is uniform between the plates and zero


elsewhere.
The capacitance is proportional to the area of its plates
and inversely proportional to the distance between the
plates.
C

A
Q
Q
Q

o
V Ed Qd / o A
d

Capacitance of a Cylindrical
Capacitor (Exa. 26.1)

Capacitance of a Spherical
Capacitor (Exa. 26.2)

10

Circuit Symbols
A circuit diagram is a simplified
representation of an actual circuit.
Circuit symbols are used to
represent the various elements.
Lines are used to represent wires.
The batterys positive terminal is
indicated by the longer line.

11

Capacitors in Parallel
When capacitors are first
connected in the circuit,
electrons are transferred from
the left plates through the
battery to the right plate,
leaving the left plate positively
charged and the right plate
negatively charged.

12

Capacitors in Parallel, 2
The flow of charges ceases when the voltage across the
capacitors equals that of the battery.
The potential difference across the capacitors is the
same.
And each is equal to the voltage of the battery
V1 = V2 = V
V is the battery terminal voltage.

The capacitors reach their maximum charge when the


flow of charge ceases.
The total charge is equal to the sum of the charges on
the capacitors.
Qtot = Q1 + Q2
13

Capacitors in Parallel, 3
The capacitors can be
replaced with one capacitor
with a capacitance of Ceq.
The equivalent capacitor
must have exactly the same
external effect on the circuit
as the original capacitors.

14

Capacitors in Parallel, final


Ceq = C1 + C2 + C3 +
The equivalent capacitance of a parallel combination
of capacitors is greater than any of the individual
capacitors.
Essentially, the areas are combined.

15

Capacitors in Series
When a battery is connected to the
circuit, electrons are transferred from
the left plate of C1 to the right plate
of C2 through the battery.
As this negative charge
accumulates on the right plate of C2,
an equivalent amount of negative
charge is removed from the left plate
of C2, leaving it with an excess
positive charge.
All of the right plates gain charges
of Q and all the left plates have
charges of +Q.

16

Capacitors in Series, cont.


An equivalent capacitor
can be found that performs
the same function as the
series combination.
The charges are all the
same.

Q1 = Q2 = Q
17

Capacitors in Series, final


The potential differences add up to the battery
voltage.
Vtot = V1 + V2 +
The equivalent capacitance is
1
1
1
1

Ceq C1 C2 C3

The equivalent capacitance of a series


combination is always less than any individual
capacitor in the combination.

18

Equivalent Capacitance,
Example (Exa. 26.3)

The 1.0-F and 3.0-F capacitors are in parallel as are the


6.0-F and 2.0-F capacitors.
These parallel combinations are in series with the
capacitors next to them.
The series combinations are in parallel and the final

equivalent capacitance can be found.

19

Energy in a Capacitor
Overview
Consider the circuit to be a system.
Before the switch is closed, the energy is
stored as chemical energy in the battery.
When the switch is closed, the energy is
transformed from chemical potential energy
to electric potential energy.
The electric potential energy is related to
the separation of the positive and negative
charges on the plates.
A capacitor can be described as a device that
stores energy as well as charge.

20

Energy Stored in a Capacitor


Assume the capacitor is being
charged and, at some point, has a
charge q on it.
The work needed to transfer a charge
from one plate to the other is

dW Vdq

q
dq
C

The work required is the area of the


tan rectangle.
The total work required is

q
Q2
dq
C
2C

21

Energy, cont
The work done in charging the capacitor appears as
electric potential energy U:
Q2 1
1
U
QV C ( V )2
2C 2
2

This applies to a capacitor of any geometry.


The energy stored increases as the charge increases and as
the potential difference increases.
In practice, there is a maximum voltage before discharge
occurs between the plates.
22

Energy, final
The energy can be considered to be stored
in the electric field.
For a parallel-plate capacitor, the energy
can be expressed in terms of the field as
U = (oAd)E2.
It can also be expressed in terms of the
energy density (energy per unit volume)

uE = oE2

23

Capacitors with Dielectrics


A dielectric is a non-conducting material that, when placed
between the plates of a capacitor, increases the capacitance.
Dielectrics include rubber, glass, and waxed paper

With a dielectric, the capacitance becomes C = Co.

The capacitance increases by the factor when the dielectric


completely fills the region between the plates.
is the dielectric constant of the material.

If the capacitor remains connected to a battery, the voltage across


the capacitor necessarily remains the same.
If the capacitor is disconnected from the battery, the capacitor is
an isolated system and the charge remains the same.
24

Dielectrics, cont
For a parallel-plate capacitor, C = (oA) / d
In theory, d could be made very small to create a very large
capacitance.
In practice, there is a limit to d.

d is limited by the electric discharge that could occur though


the dielectric medium separating the plates.

For a given d, the maximum voltage that can be applied


to a capacitor without causing a discharge depends on
the dielectric strength of the material.

25

Dielectrics, final

Dielectrics provide the


following advantages:

Increase in capacitance
Increase the maximum
operating voltage
Possible mechanical
support between the
plates

This allows the plates to be


close together without
touching.
This decreases d and
increases C.

26

Some Dielectric Constants and


Dielectric Strengths

27

Types of Capacitors

28

Types of Capacitors Variable


Variable capacitors consist of
two interwoven sets of metallic
plates.
One plate is fixed and the
other is movable.
Contain air as the dielectric
These capacitors generally
vary between 10 and 500 pF.
Used in radio tuning circuits

29

Electric Dipole
An electric dipole consists of two
charges of equal magnitude and
opposite signs.
The charges are separated by 2a.

The electric dipole moment (p) is


directed along the line joining the
charges from q to +q.

30

Electric Dipole, 2
The electric dipole moment has a magnitude of
p 2aq.
Assume
the
dipole
is
placed
in
a
uniform
external

field, E

E is

external to the dipole; it is not the field produced


by the dipole

Assume the dipole makes an angle with the field

31

Electric Dipole, 3
Each charge has a force of F = Eq acting
on it.
The net force on the dipole is zero.
The forces produce a net torque on the
dipole.
The dipole is a rigid object under a net
torque.

32

Electric Dipole, final


The magnitude of the torque is:
The torque can also be expressed
as
the
cross
product
of

the moment and the field: p E


The system of the dipole and the external electric field
can be modeled as an isolated system for energy.
The potential energy can be expressed as a function of the
orientation of the dipole with the field:
Uf Ui =pE (cos i cos fU = - pE cos
This expression can be written as a dot product.
33

Polar vs. Nonpolar Molecules


Molecules are said to be polarized when a separation exists between the average
position of the negative charges and the average position of the positive charges.
Polar molecules are those in which this condition is always present.
Molecules without a permanent polarization are called nonpolar molecules.
A water molecule is an example of
a polar molecule.
The center of the negative charge
is near the center of the oxygen
atom.
The x is the center of the positive
charge distribution.

34

Dielectrics An Atomic View


The molecules that make up the
dielectric are modeled as dipoles.
The molecules are randomly
oriented in the absence of an
electric field.

35

Dielectrics An Atomic View, 2


An external electric field is applied.
This produces a torque on the
molecules.
The molecules partially align with the
electric field.

The degree of alignment


depends on temperature and
the magnitude of the field.
In general, the alignment increases
with decreasing temperature and
with increasing electric field.

36

Dielectrics An Atomic View, 4


If the molecules of the dielectric are non-polar
molecules, the electric field produces some
charge separation.
This produces an induced dipole moment.
The effect is then the same as if the molecules
were polar.

37

Dielectrics An Atomic View,


final
An external field can polarize the
dielectric whether the molecules are
polar or nonpolar.
The charged edges of the dielectric
act as a second pair of plates
producing an induced electric field in
the direction opposite the original
electric field.

38

Energy Stored Before and After


(Exa. 26.5)

39

The H2O Molecule (Exa. 26.5)

40

Problem/Solutions

Solution

Q # 5: A 50.0-m length of coaxial cable has an inner conductor that has a diameter of 2.58 mm and carries a charge of 8.10
C. The surrounding conductor has an inner diameter of 7.27 mm and a charge of - 8.10 C. Assume the region between the
conductors is air. (a) What is the capacitance of this cable? (b) What is the potential difference between the two conductors?

Solution

41

Home Work (!!!)

42

You might also like