Scribd
Upload
576 views6 pages

Memory Save FS16-18

The document provides instructions for outputting and inputting various data types to and from a FANUC Series 16/18 CNC using its data input/output operation features. It describes how to output and input CNC parameters, pitch error compensation data, PMC parameters, custom macro variables, part programs, tool offset data, and conversational function data by configuring specific CNC parameters and following provided steps. It also lists some common alarms that could occur during these operations.

Uploaded by

DiegoBenitez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
576 views6 pages

Memory Save FS16-18

The document provides instructions for outputting and inputting various data types to and from a FANUC Series 16/18 CNC using its data input/output operation features. It describes how to output and input CNC parameters, pitch error compensation data, PMC parameters, custom macro variables, part programs, tool offset data, and conversational function data by configuring specific CNC parameters and following provided steps. It also lists some common alarms that could occur during these operations.

Uploaded by

DiegoBenitez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

FANUC Series 16/18

Data Input/Output Operation


Output the following data when it is possible in normal conditions.
a. CNC parameter
b. Pitch error compensation data
c. PMC parameters
d. Custom Macro Variables
e. CAP data
f. Part programs
g. Tool offset data
1. Check the parameters for data output operation.
The data is not able to output in alarm condition.
PRM 0000

ISO = 0
1

Output in EIA code


Output in ISO code

PRM 0020

Selection of I/O channel


0: H Channel 1 (JD5A on Main CPU board)
Set PRM 0101 ~ 0103
1:
Channel 1 (JD5A on Main CPU board)
Set PRM 0111 ~ 0113
2:
Channel 2 (JD5B on Main CPU board)
Set PRM 0121 ~ 0123
3:
Channel 3 (JD5C on Option 1 board)
Set PRM 0131 ~ 0135

PRM 0101, 0111, 0121, 0131


NFD
bit 7

(NFD) 0:
1:

bit 3

(ASI)

0:
1:

bit 0

(SB2)

0:
1:

ASI
FEED is output in punch out mode.
FEED is not output in punch out mode.
To use EIA code or ISO code.
To use ASCII code in data input mode.
1 stop bit.
2 stop bits.
18

SB2

PRM 0102, 0112, 0122, 0132


Specification of I/O device
0H
1
2
3
4
5
6

RS232C ( excluding following devices)


FANUC Bubble Cassette Adapter B1/B2
FANUC Floppy Cassette Adapter F1
Program File Mate, FA Card Adapter, Floppy Cassette, FSP-H
Not Used
Portable Tape Reader
FANUC PPR, FSP-G, FSP-H

FANUC Series 16/18 (cont.)

PRM 0103, 0113, 0123, 0133


Setting of Baudrate

PRM 0134, 0135

1:
50
2:
100
3:
110
4:
150
5:
200
6:
300
See Parameter manual
necessary.

7:
600
8:
1200
9:
2400
10: H 4800
11:
9600
12:
19200 bps
for details of these parameters, if

Output of CNC Parameters


1. Select EDIT mode.
2. Select PARAMETER screen by pressing [SYSTEM] key and (PARAM)
softkey.
3. Press (OPRT) softkey and ( > ) right arrow softkey.
4. Press (PUNCH) softkey and (EXEC) softkey.
Output of Pitch Error Compensation data
1. Select EDIT mode.
2. Select PITCH ERROR COMPENSATION screen by pressing [SYSTEM] key
and (PARAM), (>), and (PITCH) softkeys.
3. Press (OPRT) and (>) soft keys.
4. Press (PUNCH) AND (EXEC) softkeys.
Output of PMC Parameters
1. Select MDI mode.
2. Turn on Parameter Write Enable.
3. Press [SYSTEM] key and (PMC) softkey.
4. Press (PMCPRM) and (KEEPRL) softkeys.
5. Move the cursor to K17 and set bit 1 to 1.
6. Select EDIT mode.
7. Press (<) and then (>) soft keys.
8. Press (I/O) softkey to set parameters for I/O operation
CHANNEL NO. =
Press 1 and [INPUT] keys.
DEVICE NAME =
Press (FDCAS) softkey.
19

KIND OF DATA =
FUNCTION
=
FILE NO
=
9. Press (EXEC) softkey.

Press (PARAM) softkey.


Press (WRITE) softkey.
Press [-] [1] [INPUT] keys.

Output of Custom Macro Variables


1. Select EDIT mode.
2. Display TOOL OFFSET screen by pressing [OFFSET] key.
3. Press (>) and then (MACRO) softkeys to display macro variable screen.
4. Press (OPRT) and then (>) softkeys.
5. Press (PUNCH) and (EXEC) to output variables No. 500 ~ 999.

FANUC Series 16/18 (cont.)


Output of Part Programs
1. Verify NC PRM 3202 bit 4 and bit 0 = 0. If 1, 8000 and 9000 series
programs are protected and will not be output.
2. Select EDIT mode.
3. Select PROGRAM screen by pressing [PROG] key and (PRGRM) softkey.
4. Press (OPRT) and (>) softkeys.
5. Key in O-9999 to output all programs.
6. Press (PUNCH) and (EXEC) softkeys.
Output of Tool Offset Data
1. Select EDIT mode.
2. Display to TOOL OFFSET screen by pressing [OFFSET] key and (OFFSET)
softkey.
3. Press (OPRT) and (>) softkeys.
4. Press (PUNCH) and (EXEC) softkeys.
Output of Conversational Function Data
1. Select EDIT mode.
2. Display TOOL DATA MENU screen by pressing [OFFSET] key twice.
3. Press (PUNCH) softkey to output Tooling Data.

Restoring Memory
Depress EMERGENCY STOP button.
Verify correct communication parameters from output procedure.
Input of CNC Parameters
1. Display to PARAMETER screen by pressing [SYSTEM] key and (PARAM)
softkey.
2. Press (OPRT) and (>) softkey.
3. Press (READ) and (EXEC) softkeys. Parameters will be input.
4. When input is complete, power the CNC OFF and ON.
Parameter No. 1815 bit 5 set to 0 will disable an alarm 310 with an
Absolute Pulse coder system.
Input of PITCH ERROR COMPENSATION data
1. Select EDIT mode.
2. Verify Parameter Write Enable = 1.
20

3. Press [SYSTEM] key and (PARAM), ( > ), and (PITCH) softkeys.


4. Press (OPRT) and ( > ) softkeys.
5. Press (READ) and (EXEC) softkeys to input Pitch Error data.

FANUC Series 16/18 (cont.)


Input of PMC PARAMETERS
1. Verify Parameter Write Enable = 1.
2. Press [SYSTEM] key and (PMC) softkey.
3. Press (PMCPRM), then (KEEPRL) softkeys.
4. Move cursor to K17 and press [1], [0] and [INPUT].
5. Select EDIT mode.
6. Press ( < ) and then ( > ) softkeys.
7. Press (I/O) softkey, and set parameters for I/O operation.
CHANNEL NO =
press [ 1 ] and [ INPUT ] keys.
DEVICE NAME =
press (FDCAS) softkey.
FUNCTION
=
press (READ) softkey.
FILE NO
=
PRESS [ 2 ] and [ INPUT ] keys.
8. Press (EXEC) softkey to read PMC parameters.
Input of CUSTOM MACRO VARIABLES
1. Select EDIT mode.
2. Turn off the Program Protect key.
3. Press [PROGRAM] key and (PRGRM) softkey.
4. Press ( > ) softkey.
5. Press [ O ] and [ 1 ] keys, then (READ) and (EXEC) softkeys.
6. Select AUTO mode and execute program O0001.
7. Verify variables were written to Macro Variable table.
8. Delete program O0001.

Input of PART PROGRAMS


1. Set the following parameters in MDI mode, if necessary.
PRM 3201,bit 6
=
1
PRM 3201, bit 1
=
0

2.
3.
4.
5.
6.

PRM 3202, bit 4


=
0
PRM 3202, bit 0
=
0
Select EDIT mode.
Turn off the Program Protect key.
Press [PROGRAM] key and (PRGRM) softkey.
Press ( > ) softkey.
Press (READ) and (EXEC) softkeys to read part programs.
21

Input of TOOL OFFSETS


1. Select EDIT mode.
2. Turn off the Program Protect key.
3. Press the [OFFSET] key and (OFFSET) softkey.
4. Press the (OPRT) and the ( > ) softkeys.
5. Press the (READ) and (EXEC) softkeys to read in Tool Offsets.

FANUC Series 16/18 (cont.)


Input of CONVERSATIONAL function data
FS16/18-MA/TA/TTA, CAP-I
FS-16MA
1. Select EDIT mode.
2. Turn off the Program Protect key.
3. Press the [PROGRAM] key and (PRGRM) softkey.
4. Press the ( > ) softkey.
5. Press [ O ] and [ 1 ] keys, then (READ) and (EXEC) softkeys to read data.
6. Set parameter 3401 bit 0 = 0, in MDI mode.
7. Select AUTO mode.
8. Execute program O0001.
9. Confirm cutting condition and tool preparation data are restored.
10. Delete program O0001.
11. Set parameter 3401 bit 0 to 1 in MDI mode.
FS-16/18-TA, FS16/18-TTA
1. Select EDIT mode.
2. Turn off the Program Protect key.
3. Display the Tool Data Menu screen by pressing the [OFFSET] key twice.
4. Press the (READ) softkey to read in the Conversational function data.
5. Verify the data has been restored.

22

FANUC Series 16/18 (cont.)


Alarm
000

Message
PLEASE TURN OFF POWER

001

TH PARITY ALARM

002

TV PARITY ALARM

010

IMPROPER G-CODE

070

NO PROGRAM SPACE IN
MEMORY
PROGRAM NUMBER
ALREADY IN USE

073

075

PROTECT

085

COMMUNICATION ERROR

086

DR SIGNAL OFF

087

BUFFER OVERFLOW

5010

END OF RECORD

Description
A parameter which requires the power off was input,
turn off power.
TH alarm (A character with incorrect parity was input.)
Correct the tape.
TV alarm (The number of characters in a block is
odd). This alarm will be generated only when the TV
check is effective.
An unusable G code or G code corresponding to the
function not provided is specified. Modify the
program.
The memory area is insufficient. Delete any
unnecessary programs, then retry.
The commanded program number has already been
used. Change the program number or delete
unnecessary programs and execute program
registration again.
An attempt was made to register a program whose
number was protected.
When entering data in the memory by using
Reader/Puncher interface, an overrun, parity or
framing error was generated. The number of bits of
input data or setting of baudrate or specification No.
of I/O unit is incorrect.
When entering data in the memory by using
Reader/Puncher interface, the ready signal (DR) was
turned off. Power supply of I/O unit is off or cable is
not connected or a PCB is defective.
When entering data in the memory by using
Reader/Puncher interface, though the read terminate
command is specified, input is not interrupted after 10
characters read. I/O unit or PCB is defective.
The end of record (%) was specified. I/O is incorrect.
Modify the program.

23

You might also like