1ZUA 5670-201 en PDF

Drawout Expulsion Fuse Links
Type DO-III Fuse Links, Oil Immersed

PTAP-AFS928
Technical Guide
100 Amp Current Sensing Fuse Style 1B11143G16
50 Amp Dual Sensing Fuse Style 1B11144G12
8 Amp Dual Element Fuse Style 1B11145G05
General Description
Fuse Curve Selection
The DO-III Expulsion Fuse Link is an oil immersed, expulsion

type, fuse assembly for use in the ABB DO-III draw out load
break expulsion fuse holder or equivalent. It is designed for
use with single and three phase pad-mounted transformers
filled with transformer oil or other approved fluid and is designed to protect the distribution system in the event of an
internal transformer fault, secondary fault, or severe overload.
It must be used in series with a current limiting fuse or isolation Link.
There are two methods that can be used to determine the

correct DO-III Expulsion Fuse Link that will properly
coordinate with other protective devices in the system:
Application Information
The other method is to use Tables 2 through 7. Select the

proper fuse link based on the kVA and primary voltage of the
transformer to be protected. Use Tables 2 through 4 for single
phase and Tables 5 through 7 for three phase transformer
applications.
Multiple Ratings
DO-III Expulsion Fuses are manufactured in Current
Sensing, Dual Sensing, and Dual Element types of fuses per
Table1. Current Sensing Fuse Links sense secondary faults,
extreme overload currents and transformer faults, while the
Dual Sensing and Dual Element Fuse Links additionally detect excessive transformer fluid temperature to keep damage caused by extreme temperature environments and longterm overloads from occurring.
The first method is to use the time versus current characteristics curves (TCC Curves) of the DO-III Expulsion Fuse Link
and the TCC Curves of related system devices and confirm
that the DO-III Expulsion Fuse Link curve lies between its
nearest upstream and downstream device curves.
Single Phase Transformer Applications

Table 2
kVA
Table 1
DO-III Expulsion Fuse Links
Current Sensing
Dual Sensing
Dual Element
Fuse Style
Fuse Style
1B11143G04
1B11144G03
3 1B11145G03
1B11143G06 10 1B11144G05
8 1B11145G04
1B11143G08 15 1B11144G08 15 1B11145G05
Fuse Style
1B11143G10 25 1B11144G10 25 1B11145G06 12

1B11143G12 40 1B11144G12 50 1B11145G07 15
10
15
25
37.5
50
75
100
167
250
333
500
2.4
06b
08b
10b
10
12
14b
14
17b
-
Current Sensing Fuse Link a
4.16
04b
06b
08b
08
10
12b
12
14b
16
17b
-
4.8
04b
06b
06
08
10b
10
12
14b
16b
17b
-
Primary Voltage in kV
7.2 7.62 8.32 12.0 12.47 13.2 13.8
04b 04b 04b 04b 04b 04b 04b
04b 04b 04b 04b 04b 04b 04b
06b 04b 04b 04b 04b 04b 04b
06 06 06 06b 06b 04b 04b
08b 08b 08b 06b 06b 06b 06b
10b 08b 08b 08b 08b 08b 06
10 10 10 08 08
08 08
12 12 12 10 10
10 10
14b 14b 14b 12 12
12 12b
16b 14 14b 14b 12
12 12
17b 17b 16 14 14b 14b 14b
14.4
04b
04b
04b
04b
06b
06
08b
10
12b
12
14b
1B11143G14 65 1B11144G14 65 1B11145G09 25

1B11143G16 100
1B11145G11 40
1B11143G17 140
1B11145G12 50
Table 3
kVA
See TCC Curves 1C11102 for min. melt current sensing

See TCC Curves 1C11103 for max clear current sensing
See TCC Curves 1C11104 for min. melt dual sensing
See TCC Curves 1C11105 for max clear dual sensing
See TCC Curves 1C11106 for min. melt dual element
See TCC Curves 1C11107 for max clear dual element
5
10
15
25
37.5
50
75
100
167
250
333
500
Dual Sensing Fuse Link c
2.4 4.16 4.8 7.2 7.62 8.32 12.0 12.47 13.2
03 03 03 03 03 03 03 03 03
05 05 03 03 03 03 03 03 03
08 05 05 03 03 03 03 03 03
10 08 08 05 05 05 03 03 03
12 10 08 08 08 08 05 05 05
12 10 10 08 08 08 05 05 05
14 12 12 10 10 10 08 08 08
14 12 12 10 10 10 08 08 08
14 14 12 12 12 10 10 10
14 14 14 12 12 12
- 14d 14 14 12 12 12
14 14 14
13.8
03
03
03
03
05
05
08
08
10
12
12
14
14.4
03
03
03
03
05
05
08
08
10
12
12
14
ABB
Table 4
Dual Element Fuse Link c, e
Table 6
2.4 4.16 4.8 7.2 7.62 8.32 12.0 12.47 13.2
5 03 03 03 03 03 03 03 03 03
10 05 04 04 03 03 03 03 03 03
15 07 05 05 03 03 03 03 03 03
25 09 06 06 04 04 04 03 03 03
37.5 11 09 08 06 06 06 05 05 04
50 12 09 09 07 07 07 06 06 05
75 - 12 11 09 09 09 07 06 06
100 - 12 12 09 09 09 09 09 07
167 - 12 12 12 11 11 09
250 - 12 12 11
333 - 12 12 12
Dual Sensing Fuse Link f
kVA
13.8
03
03
03
03
04
05
06
07
09
11
12
kVA
14.4
03
03
03
03
04
05
06
07
09
11
12
45
75
112.5
150
225
300
500
750
1000
1500
2.4 4.16 4.8

10
12
14
14
-
Table 7
08
10
12
12
14
14
-
08
10
10
12
14
14
-
Dual Element Fuse Link f
Single Phase Application Notes

a.
Fuse recommendations are based on fuse melting at 3 to 4 times

transformer rated current at 5 minutes. Recommended fuses
meet inrush requirement of 12 times transformer full load current
for 0.1 second.
Recommended Fuses provide more than 4 times
Transformer rated current for 5 minutes.
Recommendations are based on 200% transformer
loading for 2 hours, 160% loading for 7 hours and thermal
characteristics of typical ABB Transformers. Recommended
fuses meet inrush requirement of 12 times transformer
full load current for 0.1 second.
Recommended fuse will result in some loss of overload capacity.
b.
c.
d.
e.
ABB DO-III Expulsion Fuse Links 1B11145G09-G12

should not be used at voltages greater than 15500 V for
delta configuration.
kVA
45
75
112.5
150
225
300
500
750
1000
a.
c.
Three Phase Transformer Applications
kVA
45
75
112.5
150
225
300
500
750
1000
1500
2000
2500
ABB
Current Sensing Fuse Link a
2.4 4.16 4.8

10b
12b
12
14b
16b
17b
-
08b 06
10b 08
10 10
12 12b
14b 12
14 14b
17b 16
17
-
12.0,
13.8,
8.32
13.2
20.8c,d
12.47
14.4
06b 04b 04 b 04b 04b
06 06b 06 b 06b 04b
08 06 06 06 06b
10b 08b 08 b 08b 06b
10 10b 10 b 08 08b
12 10 10 10
08
14b 12 12 12
10
16b 14b 14 b 14b 12
17b 16b 14 14 14b
14
17b 17 b 16
17 17 16b
17b
d.
e.
f.
22.9c,d 24.94c
04b
04b
04b
06b
08b
08
10
12
12
14b
16b
17b
07
09
11
12
-
07
09
09
12
-
12.0,
13.8,
8.32
13.2
20.8 c,d 22.9 c,d 24.94 d
12.47
14.4
04 03 03 03
03
03
03
06 04 04 04
03
03
03
07 06 06 06
05
04
04
09 07 07 07
06
05
05
11 09 09 09
07
06
06
12 09 09 09
09
07
07
12 12 12
11
09
09
12
11
11
12
12
Three Phase Application Notes
b.
Table 5
2.4 4.16 4.8

09
12
-
12.0,
13.8,
8.32
13.2
20.8c,d 22.9 c,d 24.94 d
12.47
14.4
05 03 03 03 03
03
03
08 05 05 05 03
03
03
08 08 08 08 05
05
05
10 08 08 08 05
05
05
12 10 10 10 08
08
08
12 10 10 10 08
08
08
14 12 12 12 10
10
10
12
12
14 14 14 12e
- 14e 14e 14e 12e
12
12
14
14
14
04b
04
04
06
06
08
10
12
12
14b
16b
16
Fuse recommendations are based on fuse melting at 3 to 4 times

transformer rated current at 5 minutes. Recommended fuses
meet inrush requirement of 12 times transformer full load current
for 0.1 second.
Recommended Fuses provide more than 4 times Transformer
rated current for 5 minutes.
ABB DO-III Expulsion Fuse Links alone should not be used at
voltages greater than 17100 V for delta configuration or 24940
gnd Y/14400. For application through 23 kV delta or 34500 gnd
Y/19920 a 23 kV rated current limiting fuse is recommended in
series with the DO-III Expulsion Fuse Link.
Recommended fuse is limited to gnd Y /gnd Y transformer with
less than 50% delta loading.
Recommended fuse will result in some loss of overload capacity.
Recommendations are based on 200% transformer loading for 2
hours, 160% loading for 7 hours and thermal characteristics of
typical ABB Transformers. Recommended fuses meet inrush requirement of 12 times transformer full load current for 0.1 second. ABB DO-III Expulsion Fuses 1B11145G09 through G12
should not be used at voltages greater than 15500V for delta
configuration. ABB DO_III Expulsion Fuses 1B11145G03 through
G07 alone should not be used at voltages greater than 17100 V
for delta configuration or 24940 gndY/14400.
ABB, Inc.
1128 S. Cavalier Drive
Alamo, TN 38001, USA
Telephone: 731-696-5561
Fax: 731-696-5269
www.abb.com
IZUA 5670-201en Replaces TPL 44-836 dated March 01.
Printed in USA by Tennessee Industrial Printing Services Inc.
Type DO-III Fuse Links, Oil Immersed

Drawout Expulsion Fuse Links
PTAP-AFS928
Installation Information
Removing the Existing Fuse
1.
WARNING: VENT THE TRANSFORMER BEFORE

OPERATING THE BAYONET FUSE HOLDER. FAILURE
TO DO SO CAN CAUSE SEVERE INJURY, DEATH OR
PROPERTY DAMAGE.
4.
Quickly pull the fuseholder out approximately 6 inches to open

the circuit. Wait a few seconds for oil to drain back into the
tank, then completely withdraw fuse holder. (See Figure 3)
Vent the transformer to atmosphere by manually operating

the pressure relief device normally provided, or by removing
the vent plug. The transformer should be vented before it is
energized if it has been pressurized for leak test or if the unit
has been opened and resealed.
2.
Attach Hot-Line tool to handle eye, Stand to one side and

unlock the handle. (See Figure 1)
Figure 3
5.
Use a 3/4 inch and 1/2 inch wrench to remove the end plug
from the fuse cartridge. (See Figure 4)
Figure 1
3.
Push down and rotate the handle 90 clockwise in the

housing to break any adhesion between the gasket and the
housing. (See Figure 2)
Figure 4
6.
Use a flat head screwdriver or other tool to straighten out the

castle end of the fuse so that the fuse may be removed.
7.
Use a 3/4 inch wrench to remove the fuse cartridge from the
puller assembly and remove and discard the damaged fuse.
(See Figure 5)
Figure 2
Figure 5
NOTE: FOLLOW ALL FEDERAL, STATE AND LOCAL LAWS AND REGULATIONS WITH REGARD TO DISPOSING OF ALL MATERIAL
INCLUDING FUSES.
WARNING: INSURE THAT THE CORRECT FUSE IS

BEING INSTALLED IN THE FUSE HOLDER. FAILURE
TO DO SO CAN RESULT IN SEVERE INJURY, DEATH
OR PROPERTY DAMAGE
Place the Fuse in the fuse holder and thread the fuseholder
onto the puller assembly with the flared end toward the puller
assembly. Tighten to 50-70 inch pounds.
9.
Thread the end plug against the fuses castle end of the
fuseholder and tighten to 50-70 inch pounds.
(See Figure 6)
Remove the end plug and ensure that the catle ends have
flared evenly.
Replace the end plug and retighten to 50-70 inch pounds.
10. To Reinstall Fuseholder:

Attach hot-line tool to handle eye, stand to one side and
place the fuse holder end just inside the housing.
Rapidly push the fuseholder in until dust cap seats against
the housing (See Figure 7.)
Printed in USA by Tennessee Industrial Printing Services Inc.
8.
Figure 7
ABB
ABB Inc.
1128 S. Cavalier Drive
Alamo, TN 38001, USA
Telephone: 731-696-5561
Fax: 731-696-5362
www.abb.com
IZUA 5670-203 en Replaces IL 44-836 dated March 01.
Figure 6
Push down and rotate the locking handle, hooking it over the
shoulder of the housing.

1ZUA 5670-201 en PDF

Uploaded by

Copyright:

Available Formats

1ZUA 5670-201 en PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1ZUA 5670-201 en PDF

Uploaded by

Copyright:

Available Formats

Drawout Expulsion Fuse Links

Type DO-III Fuse Links, Oil Immersed

100 Amp Current Sensing Fuse Style 1B11143G16

50 Amp Dual Sensing Fuse Style 1B11144G12

8 Amp Dual Element Fuse Style 1B11145G05

Fuse Curve Selection

The DO-III Expulsion Fuse Link is an oil immersed, expulsion

There are two methods that can be used to determine the

The other method is to use Tables 2 through 7. Select the

Single Phase Transformer Applications

DO-III Expulsion Fuse Links

1B11143G08 15 1B11144G08 15 1B11145G05

1B11143G10 25 1B11144G10 25 1B11145G06 12

Current Sensing Fuse Link a

1B11143G14 65 1B11144G14 65 1B11145G09 25

See TCC Curves 1C11102 for min. melt current sensing

Dual Sensing Fuse Link c

Dual Element Fuse Link c, e

Dual Sensing Fuse Link f

2.4 4.16 4.8

Dual Element Fuse Link f

Single Phase Application Notes

Fuse recommendations are based on fuse melting at 3 to 4 times

ABB DO-III Expulsion Fuse Links 1B11145G09-G12

Three Phase Transformer Applications

Current Sensing Fuse Link a

2.4 4.16 4.8

Three Phase Application Notes

2.4 4.16 4.8

Fuse recommendations are based on fuse melting at 3 to 4 times

IZUA 5670-201en Replaces TPL 44-836 dated March 01.

Printed in USA by Tennessee Industrial Printing Services Inc.

Type DO-III Fuse Links, Oil Immersed

WARNING: VENT THE TRANSFORMER BEFORE

Quickly pull the fuseholder out approximately 6 inches to open

Vent the transformer to atmosphere by manually operating

Attach Hot-Line tool to handle eye, Stand to one side and

Push down and rotate the handle 90 clockwise in the

Use a flat head screwdriver or other tool to straighten out the

WARNING: INSURE THAT THE CORRECT FUSE IS

10. To Reinstall Fuseholder:

Printed in USA by Tennessee Industrial Printing Services Inc.

IZUA 5670-203 en Replaces IL 44-836 dated March 01.

You might also like