Fourth-Axis Beta-I Drive Kit User Manual B-165A

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

Fourth-Axis Beta-i Drive Kit User Manual B-165A

Installation Instructions
for the Hardinge

Fourth-Axis Beta-i Drive Kit


(Required to operate a Hardinge GD5C2, GD16C2, GD3J2 or GD160LP Rotary Table Indexer
via true fourth axis on a Bridgeport GX 480 Vertical Machining Center)

Part No. BA -0009500-0165

Original U.S.A. Instructions

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Fourth-Axis Beta-i Drive Kit User Manual B-165A

Table of Contents
Safety Recommendations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1. Introduction
1.1 Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.3 Suggested Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2. Set Up

2.1 Back up the original parameters on the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.2 Powering down the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 ..

2.3 Locating the fiber optic port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ..

2.4 Mounting the fourth-axis Beta-i drive and dynamic brake resistor. . . . . . . . . . . . . . . . . . . . . 9.

2.5 Installing the three-phase power cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.6 Connecting the dynamic brake resistor and fiber optic cable. . . . . . . . . . . . . . . . . . . . . . . . 12

2.7 Locating the two fourth-axis wires in the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.8 Installing the chassis ground wire and connecting the shield wire of the feedback cable. . . 14

2.9 Installing the 24-volt power cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15.

2.10 Installing the drive enable cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.11 Preparing the machine for a Hardinge fourth-axis rotary with a 24vdc clamp solenoid . . . 18

3. Modifying the Parameters


3.1 Modify the parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

3.2 Single-Axis Parameter Setup Sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.

Part No. BA -0009500-0165

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Fourth-Axis Beta-i Drive Kit User Manual B-165A


Safety Recommendations
READ COMPLETE INSTRUCTIONS CAREFULLY BEFORE OPERATING THIS UNIT. NOTE: Equipment refers to
the rotary table and/or machine it is used with.
When this instruction book was printed, the information given was current. However, since we are constantly improving the design of our products, it is possible that the illustrations and descriptions may vary from the system.
- WARNING Occupational Safety and Health Administration (OSHA) Hazard Communication Standard 1910.1200, effective May
25, 1986, and various state "employee right-to-know laws" require that information regarding chemicals used with this
equipment be supplied to you. Refer to the applicable section of the Material Safety Data Sheets supplied with your unit
when handling, storing or disposing of chemicals.
HARDINGE SAFETY RECOMMENDATIONS
Your Hardinge rotary table is designed and built for maximum ease and safety of operation. However, some previously
accepted shop practices may not reflect current safety regulations and procedures, and should be re-examined to
insure compliance with the current safety and health standards.
Hardinge Inc. recommends that all shop supervisors, maintenance personnel, and machine tool operators be advised
of the importance of safe maintenance, setup and operation of Hardinge-built equipment. Our recommendations are
described below.
READ THESE SAFETY RECOMMENDATIONS BEFORE PROCEEDING ANY FURTHER.
READ THE APPROPRIATE MANUAL OR INSTRUCTIONS before attempting operation or maintenance of the
equipment. Make certain that you understand all instructions.
DO NOT ALLOW the operation or repair of equipment by untrained personnel.
CONSULT YOUR SUPERVISOR when in doubt as to the correct way to do a job.
WEAR SAFETY GLASSES AND PROPER FOOT PROTECTION at all times. When necessary, wear respirator, helmet,
gloves and ear muffs or plugs.
DO NOT OPERATE EQUIPMENT unless proper maintenance has been regularly performed and the equipment is
known to be in good working order.
WARNING or INSTRUCTION TAGS are mounted on the unit for your safety and information. Do not remove them
or damage them.
DO NOT ALTER THE EQUIPMENT to bypass any interlock, overload, disconnect or other safety device.
DO NOT OPERATE EQUIPMENT if unusual or excessive heat, noise, smoke, or vibration occurs. Report any excessive
or unusual vibration, sounds, smoke or heat as well as any damaged parts.
LIFTING AND HANDLING OF THE UNIT should be done with full knowledge of the unit weight and using proper
procedures.
MAKE CERTAIN that the equipment is properly grounded. Consult National Electric Code and all local codes.

DONT TOUCH ELECTRICAL EQUIPMENT when hands are wet or when standing on a wet surface.
(Where Applicable)
REPLACE BLOWN FUSES with fuses of the same size and type as originally furnished. (Where Applicable)

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

Remove power from the unit by unplugging the power cord before attempting repair or maintenance.
(Where Applicable)

Fourth-Axis Beta-i Drive Kit User Manual B-165A


Safety Recommendations (continued)
ASCERTAIN AND CORRECT the cause of a shutdown caused by overload heaters before restarting the machine.
(Where Applicable)
KEEP THE AREA AROUND THE MACHINE well lit and dry.
KEEP CHEMICAL AND FLAMMABLE MATERIAL away from electrical or operating equipment.
HAVE THE CORRECT TYPE OF FIRE EXTINGUISHER handy when machining combustible material and keep chips
clear of the work area.
DONT USE a toxic or flammable substance as a solvent cleaner or coolant.
MAKE CERTAIN THAT PROPER GUARDING is in place and that all doors to the primary machine are closed
and secured.
DONT OPEN GUARD DOORS of the primary machine while any machine component is in motion.
MAKE SURE chucks, closers, fixture plates and all other spindle-mounted workholding devices are properly mounted
and secured before starting the unit or the machine.
MAKE CERTAIN all tools are securely clamped in position before starting the unit or the machine.
REMOVE ANY LOOSE PARTS OR TOOLS left on the unit or the machine or in the work area before operating the
equipment. Always check the machine and work area for loose tools and parts especially after work has been completed by maintenance personnel.
REMOVE CHUCK WRENCHES before starting the unit or the machine.
BEFORE PRESSING THE CYCLE START PUSH BUTTON, make certain that proper functions are programmed and that
all controls are set in the desired modes.
KNOW WHERE ALL STOP push buttons are located in case of an emergency.
CHECK THE LUBRICATION OIL LEVEL before operating the machine.
MAKE CERTAIN that all guards are in good condition and are functioning properly before operating the equipment.
INSPECT ALL SAFETY DEVICES AND GUARDS to make certain that they are in good condition and are functioning
properly before the cycle is started.
CHECK THE POSITION of any load/unload automation before pressing the CYCLE START push button.
CHECK SETUP, TOOLING, AND SECURITY OF THE WORKPIECE if the machine has been OFF for any length
of time.
DRY CYCLE a new setup to check for programming errors.
MAKE CERTAIN that you are clear of any "pinch point" created by moving slides before starting the machine.
DONT OPERATE any equipment while any part of the body is in the proximity of a potentially hazardous area.
DONT REMOVE CHIPS with hands. Use a hook or similar device and make certain that all machine movements have
ceased.
BE CAREFUL of sharp edges when handling a newly machined workpiece.
DONT REMOVE OR LOAD a workpiece while any part of the equipment is in motion.
DONT OPERATE ANY EQUIPMENT while wearing rings, watches, jewelry, loose clothing, neckties or long hair not
contained by a net or shop cap.
DONT LEAVE tools, workpieces or other loose items where they can come in contact with a moving component
of the equipment.
DONT CHECK finishes or dimensions of workpiece near running spindle or moving slides.
DONT JOG SPINDLE in either direction when checking threads with a thread gage.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

DONT ADJUST tooling or coolant hoses while the equipment is running.

Fourth-Axis Beta-i Drive Kit User Manual B-165A


Safety Recommendations (continued)
DONT ATTEMPT to brake or slow the equipment with hands or any makeshift device.
ANY ATTACHMENT, TOOL OR MACHINE MODIFICATION not obtained from Hardinge Inc. must be reviewed by
a qualified safety engineer before installation.
USE CAUTION around exposed mechanisms and tooling especially when setting up. Be careful of sharp edges on tools.
DONT USE worn or defective hand tools. Use the proper size and type for the job being performed.
USE ONLY a soft-faced hammer on tooling and fixtures.
DONT USE worn or broken tooling on machine.
MAKE CERTAIN that all tool mounting surfaces are clean before mounting tools.
INSPECT ALL CHUCKING DEVICES daily to make certain that they are in good operating condition. Replace any
defective chuck before operating the machine.
USE MAXIMUM ALLOWABLE gripping pressure on the chuck. Consider weight, shape and balance of the workpiece.
DONT EXCEED the rated capacity of the equipment.
DONT LEAVE the equipment unattended while it is operating.
DONT CLEAN the equipment with an air hose.
KEEP TOTE PANS a safe distance from the machine. Dont overfill the tote pans.
DONT LET STOCK project past the back end of the collet closer or equipment spindle without being adequately
covered and properly supported.
UNLESS OTHERWISE NOTED, all operating and maintenance procedures are to be performed by one person.
To avoid injury to yourself and others, be sure that all personnel are clear of the equipment when opening or closing
the coolant guard door and any access covers.
FOR YOUR PROTECTION - WORK SAFELY
DONT OPERATE THE EQUIPMENT with damaged or worn electrical cables.

Part No. BA -0009500-0165

VERIFY that the electrical cables are not restrained or pinched during full travel movement of the machine.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Fourth-Axis Beta-i Drive Kit User Manual B-165A


1. Introduction
1.1 Description
The Hardinge Fourth-Axis Beta-i Drive Kit contains wiring and components necessary to operate a Hardinge geardriven rotary unit via fourth-axis of the CNC. The machine must have the fourth-axis pre-wiring installed. Hardinge
rotary models GD5C2, GD16C2, GD3J2 and GD160LP rotary table indexers can be mounted on a Bridgeport GX 480
vertical machining center and operate via fourth-axis when this kit is installed.
1.2 Fourth-Axis Beta-i Drive Kit Parts List

Figure
A
B
C
D
E
F
G

Part Number
A06B6130H002
A06B6130H402

Description
20-Amp Beta-i Servo Drive
Dynamic Brake Resistor
Connectors (shown attached)
Chassis Ground Wire
A66L60010026L2R003 Fiber Optic Cable
CI 0003011I36I
Three-Phase Power Cable
CI 0003011I36F
24-Volt Power Cable
CI 0003011I36J
Drive Enable Cable for CE machine
CI 0003011I36E
Drive Enable Cable for non-CE machine
Wire-Joint (not shown)
Large Ty-wrap (not shown)
Small Ty-wrap (not shown)
M4 x .7 x 8mm SHCS (not shown)

Qty
1
1
2
1
1
1
1
1
1
2
2
10
7

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

Fourth-Axis Beta-i Drive Kit Part No. CI 000040016AE

Fourth-Axis Beta-i Drive Kit User Manual B-165A


1.3 Suggested Tools
1. Power drill and #30 tap drill
2. M4 x .7 tap and tap handle
3. M4 Allen wrench(s) - ball-nose or long T-handle
4. Diagonal wire cutters
5. Needle nose pliers - fine
6. center punch
7. Fine-tip felt marker pen
8. Pin crimpers for dynamic brake resistor
9. Clean shop rags
10. Wire strippers - 18-22 average
11. Crimping tool for wire joints

2. Set Up
2.1 Back up the original machine parameters from the CNC control
Insert a card into the card slot.
The Setting Screen should be set to Channel 4 and set Parameter Write to 1.
(You may need to hit Cancel & Reset to clear an alarm)
Push the System key.
Right arrow until you see the All IO screen, click on All IO screen and go into Edit mode.
Save parameters by selecting parameter, push OPRT, and File Output.
Name the file using the keypad incorporating a (.txt) suffix.
Push F Name to store the name in the alpha file.
Push Execute to save the parameters on the card.
2.2 Powering Down the Machine


E-STOP OFF
Push the E-Stop button on the operator control panel in the front of the machine.
Turn off the control by pushing the OFF button.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

Before adding the fourth-axis Beta-i drive, you must power down the machine:

Fourth-Axis Beta-i Drive Kit User Manual B-165A

Turn off the main power to the machine on the power


panel in the rear of the machine by rotating the selector
switch counterclockwise to the OFF position. This allows
access to the inside of the power panel.
Disconnect the machine from the main power supply
at the fuse box or other source so that the machine is
totally isolated from power.

CAUTION: Wait for the light to go out under the Fanuc Beta-I SVPM3 drive package, indicating that the drives have
discharged and the DC output bus has gone to zero. Discharge time could take over two minutes.
2.3 Locating the Fiber Optic Port

NOTE: If the combination drive package on the machine does NOT have a COP10A connection (many older
machines do not), then the fiber optic cable must be removed from the COP10B port on the SVMP3 drive package and
re-attached to the COP10B port on the fourth-axis Beta-i drive. Then the kit provided fiber optic cable is run from
the COP10A port on the fourth-axis Beta-i drive to the COP10B connector on the SVMP3 drive package. This inserts
the fourth-axis Beta-i drive between the Fanuc CNC control and the SVMP3 drive package. In this case there is only
one fiber optic cable on the combination drive package and there are two fiber optic cables connected to the fourthaxis Beta-i drive. The FSSB drive allocation table in the control must then be re-assigned. Please call the factory for
complete instructions.
8

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

The newer Fanuc SVMP3 drive packages have a COP10A and a COP10B fiber optic port to the right of the SVPM3
drive package (yellow box). The COP10A optic port provides the ability to add a fourth-axis after the SVMP3 package.

Fourth-Axis Beta-i Drive Kit User Manual B-165A


2.4 Mounting the Fourth-Axis Beta-i Drive and Dynamic Brake Resistor

There are four pre-drilled holes to the left of the yellow SVMP3 drive package that match the footprint of the Beta-i
drive. This is where you will mount the drive. Mount the Beta-i drive using four M4 SHCS screws. Hand-tighten using
an M4 ball-nosed Allen wrench or an 8-inch M4 T-handle Allen wrench.

Part No. BA -0009500-0165

Beta-i Electrical Connection Diagram

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Fourth-Axis Beta-i Drive Kit User Manual B-165A


Before mounting the resistor, you will have to crimp the supplied connectors to the wires of the resistor and then drill
and tap two M4 holes to mount the resistor.

Crimp pins on the wires and mount them into the plugs

10

Punch indents in the panel on your two marks to aid in the drilling process.
Drill each hole using a #30 tap drill size to thread for M4 x .7 SHCS screws.
Tap each hole.
Screw in the top M4 SHCS screw and slide the resistor into position.
Screw in the bottom screw and hand tighten both screws using an M4 Allen wrench.
Lift the wires and carefully remove the shop rag so that no metal filings are left on the ledge in the power panel.

NOTE: All connectors on the Fourth-Axis Beta-i Drive are keyed and will only plug in one way.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

Hold the resistor in the desired mounting position as shown.


Mark the mounting hole locations for drilling.
CAUTION: Place a clean shop rag on the ledge below the panel before drilling to catch any metal filings.

Fourth-Axis Beta-i Drive Kit User Manual B-165A


2.5 Installing the Three-Phase Power Cable

Connect the power cable in the upper two connections labeled L1 and L3 on the left side of the Beta-i fourthaxis drive at connector location CZ7.

Part No. BA -0009500-0165

Remove the gray terminal cover just below the main terminal box on the SVPM3 drive package and connect the
four terminal connectors as indicated below:
Unscrew the earth terminal and screw in the E (green earth) wire connector to it.
Continue connecting the R8 (black wire), S8 (white wire) and T8 (red wire).
Snap the terminal cover back into position.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

11

Fourth-Axis Beta-i Drive Kit User Manual B-165A


2.6 Connecting the Dynamic Brake Resistor and Fiber Optic Cable

Remove the (2) protective vinyl covers from each end of the fiber optic cable.
Remove the COP10B port cover on the Beta-i fourth-axis drive and insert one end of the fiber optic cable
(both ends of the cable are identical).

12

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

The wide connector (black wire) plugs into DCP port or slot 3 of connector CZ7 on the
Beta-i fourth-axis drive.
The thermostat wire connector (white wire) plugs into the bottom left connector labeled CXA20/DCOH
on the Beta-i fourth-axis drive.

Fourth-Axis Beta-i Drive Kit User Manual B-165A

Remove the COP10A port cover on the SVMP3 drive package and connect the other end of the fiber optic
cable into the COP10A port.
2.7 Locating and connecting the machine's fourth-axis cables
The machine comes pre-wired with a motor power cable and a feedback cable for the fourth-axis Beta-i drive.

Remove the central wire-way cover and open the plastic bag to locate the two fourth-axis cables.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

NOTE: Early GX production machine prewire kits came with a 40-amp drive motor plug connector on them.
This will have to be removed and replaced with the proper 20-amp drive - motor plug connector. Contact your
machine distributor for a plug replacement kit.

13

Fourth-Axis Beta-i Drive Kit User Manual B-165A

The motor power cable plugs into the remaining lower three slots of the CZ7 plug and the feedback cable plugs into
the JF1 terminal on the Beta-i fourth-axis drive. The light green shield wire will be connected in the next section.
Push the two cables in between the wireway fingers and snap the wireway cover back temporarily into position
to prevent other cables and wires from falling out.
2.8 Installing the Chassis Ground Wire and connecting the Shield Wire of the Feedback Cable

Attach one end of the ground wire to the ground screw connection under the base of the Beta-i Drive using
an M4 SHCS screw.
Attach the other end to the ground screw on the SVMP3 drive package as shown. The SVMP3 ground screw
will have another ground wire with the E (earth) wire label.

14

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

Chassis Ground Wire (green)

Fourth-Axis Beta-i Drive Kit User Manual B-165A

Snip the nylon ty-wrap to release the light green shield cable from the feedback cable that is connected in the JF1 port
of the Beta-i Drive. Wrap the wire around the feedback cable a couple of times and connect it to any available terminal on the ground terminal block located below the wireway cover to ground the shielding of the feedback cable.

Plug the single connector into the CXA19B connector on the upper right side of the Beta-i fourth-axis drive.
Run the wire through the wireway fingers and run them down to the lower plastic covered terminal block in the
bottom left area of the power panel. Remove the plastic terminal cover and the wireway cover.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

2.9 Installing the 24-Volt Power Cable

15

Fourth-Axis Beta-i Drive Kit User Manual B-165A

Part No. BA -0009500-0165

Hook the red wire to the P24 terminal and the black wire to the 0VP terminal, and tighten them down with
a screwdriver.

16

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Fourth-Axis Beta-i Drive Kit User Manual B-165A


2.10 Installing the Drive Enable Cable
There are two cables in the kit that are supplied with wire joints to splice into the existing wiring of the machine. Use
the cable whose wire labels match the wire labels on CX4 of the Fanuc SVMP3 drive package. One cable is for CE
machines and the other would be used for non-CE machines.

Part No. BA -0009500-0165

Plug the appropriate drive enable cable into the CX30 connector on the lower left side of the Beta-i fourth-axis
drive. Run the cable down through the wireway fingers and over to the top row of terminals on the relay module
located on the left wall of the main enclosure.
The red wire from the cable must be connected with a wire joint to either 212 (non-CE) or 225 (CE).
The black wire from the cable must be connected with a wire joint to wire 216 in either the CE or non CE machine.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

17

Fourth-Axis Beta-i Drive Kit User Manual B-165A

18

Remove the wireway cover of the vertical wireway located on the left wall of the power panel.

Fish out the cable labeled 4 Axis Power and trace the wire that is plugged into the #211 terminal on the bottom
row of terminals on the relay module.

Remove the wire from terminal #211 and move it to the 0VC terminal to the left of the original position.
Hardinge geared tables other than the 5C use a 24vdc clamp solenoid.

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

2.11 Preparing the machine for a fourth-axis Hardinge Rotary with 24vdc clamp solenoid

(skip this section if installing a 5C rotary indexer with no clamp)

Fourth-Axis Beta-i Drive Kit User Manual B-165A

There are two jumpers on the relay module that must be set.
Set JP1 to 190B for geared rotary tables.
Set JP7 for +24VA.
Clean up all wire routing.

3. Modifying the Parameters


3.1 Modify the parameters according to the setup sheet provided
Example: To go to parameter 1005
Push the System key, Parameter, type in 1005, push Number Search, cursor down to A (fourth-axis), cursor to bit 5
(the third* data field) and change to 0.
*The bit locations run from left-to-right 7, 6, 5, 4, 3, 2, 1, 0
Set all of the parameters according to the following setup sheet.
3.2 Single-axis Setup Sheet for the Bridgeport GX 480 with Fanuc 0iMD Control

Record your serial numbers for future reference:



GX 480 Bridgeport machine

Hardinge rotary Model number

Hardinge rotary Serial number

______________________________________________
______________________________________________
______________________________________________

Hardinge Inc. One Hardinge Drive, Elmira, New York U.S.A. 14902-1507 800.843.8801 (Canada 800.468.5946) www.shophardinge.com

Part No. BA -0009500-0165

A separate setup sheet is included that applies to GX 480 machine and your specific rotary table model.

19

Hardinge Inc. One Hardinge Drive | P.O. Box 1507 | Elmira, New York 14902-1507 USA
USA: 800-843-8801 | Canada: 800-468-5946 | Fax: 607-734-3886
To Order Online: www.shophardinge.com | Corporate Homepage: www.hardinge.com | E-mail: info@shophardinge.com | Live Online Support: www.shophardinge.com
All specifications are subject to change without notice due to ongoing continuous improvement. All marks indicated by and are trademarks of Hardinge Inc.
Instruction Manual B-165 Litho in USA Hardinge Inc. 2012

You might also like