Aslan 100

FIBERGLASS REBAR

Aslan 100

FIBERGLASS REBAR

CONCRETE IN

Corrosive Applications

Concrete Exposed to De-Icing Salts

Bridge decks, Median barriers, Approach slabs,

Parking structures, Railroad crossings, Salt storage facilities

Concrete Exposed to Marine Salts

Seawalls, Buildings & structures near

waterfronts, Aquaculture operations, Artificial reefs and water breaks, Floating marine docks

Tunneling and Mining Applications

Soft-eye openings for tunnel boring machine (TBM's) and

temporary works, Rock nails, Electrolytic and ore extraction tanks

Other Corrosive Applications

Concrete used in chemical plants and containers

Pipeline and chemical distribution facilities

Any polymer concrete requiring reinforcement

Architectural precast and cast stone elements

Thin concrete sections where adequate cover

is not available

Swimming Pools Architectural Cladding Brine Tanks

Impervious to chloride ion and low pH chemical attack

Tensile strength greater than steel
1/4th weight of steel reinforcement
Transparent to magnetic fields and radio frequencies
Non-conductive
Thermally non-conductive

Where should GFRP

Rebar be considered?

Potential of
GFRP Rebar
Significantly improve the
longevity of civil engineering
structures
Strengthen and rehabilitate
masonry structures

Aslan 100

FIBERGLASS REBAR

Benefits of GFRP Rebar

Any concrete member susceptible to corrosion of steel reinforcement by chloride ion or

chemical corrosion
Any concrete member requiring non-ferrous reinforcement due to electro-magnetic
considerations
As an alternative to epoxy, galvanized or stainless steel rebar
Only in secondary load bearing members
Strengthening existing unreinforced masonry walls for seismic, wind or blast loads
Rehabilitate existing masonry

CONCRETE IN

Electromagnetic
Applications
MRI rooms in hospitals
Airport radio & compass calibration pads
Electrical high voltage transformer vaults and
support pads
Concrete near high voltage cables and
substations

Masonry Strengthening
Flexural and shear strengthening of existing unreinforced
masonry for seismic, wind or blast loading events.
Rehabilitate existing masonry with step cracks and other bed
joint issues.

Aslan 100

FIBERGLASS REBAR

Physical Properties - Aslan 100, 101 GFRP Rebar

Aslan 100 Vinylester Matrix GFRP Rebar - Diameters #2 (6mm) through #8 (25mm)
Aslan 101 Polyester Matrix GFRP Rebar for non-portland cement and temporary use applications.
I. Tensile Stress, Nominal Diameter & Cross Sectional Area
Tensile
Guaranteed
Modulus
Bar Size
Cross Sectional Area*
Nominal Dia.
Tensile Strength
of Elasticity
2
2
(mm) (inches)
(mm )
(in )
(mm)
(in)
(MPA) (ksi)
GPA
psi 106
6
9
13
16
19
22
25
29
32

#2
#3
#4
#5
#6
#7
#8
#9
#10

33.23
84.32
144.85
217.56
295.50
382.73
537.90
645.00
807.34

0.0515
0.1307
0.2245
0.3372
0.4580
0.5932
0.8337
1.0000
1.2513

6.35
9.53
12.70
15.88
19.05
22.23
25.40
28.65
31.75

0.25"
0.375"
0.50"
0.625"
0.75"
0.875"
1.0"
1.123"
1.25"

825
760
690
655
620
586
550
517
480

120
110
100
95
90
85
80
75
70

40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8
40.8

ULT Strain

5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92
5.92

Hughes Brothers reserves the right to make improvements in the product and/or process which may result in benefits or changes to some physical-mechanical characteristics. The data contained herein
is considered representative of current production and is believed to be reliable and to represent the best available characterization of the product as of December, 2002.
*By water displacement, varies within tolerances over time throughout production run (0.030" from nominal).

Cross Sectional Area

The cross sectional area of the rebar
may be determined by immersing a
sample in water and measuring the volume displacement of the piece. When
calculating the cross sectional area, the
cross section is assumed to be a circle.

Tensile Stress
Tensile stress values shown are determined as the average failure load
divided by the cross sectional area
based on nominal bar diameter, less
three standard deviations. Tensile
stress varies as diameter increases
due to shear lag which
develops between the fibers in the
larger sizes. For AC1440.1R-01 design,
this value is the guaranteed tensile
strength, ffu.

Results of destructive tensile testing performed at

Penn State University

Typical Stress / Strain Curve for GFRP Rebar

700
600

Stress (MPa)

Nominal Diameter
The nominal diameter of the rebar is
the average diameter and assumes the
shape of the rebar is a circle.

500
400
300
200

E=40.798 GPa

100
0

0.005

0.01

0.015

Strain

0.02

Certification of Measured Mechanical Properties

Test reports from an independent lab are available on request for each production lot. Reports
show the tensile strength of the sample population, average tensile modulus and the calculated
ultimate strain for each tensile test based on the average modulus.

ASLAN 100 Fiberglass Rebar

0.025

Physical Properties - Continued

Aslan 100

FIBERGLASS REBAR

II. Modulus of Elasticity

The variation in the Modulus of Elasticity of different
diameter bars is much smaller than that of
the tensile stress.
Modulus of Elasticity .......

40.81 G PA
(5.92 X 106 psi)

Published values are an average modulus from a

population of samples.

LVDTs measuring
elongation during
tensile test.

III. Bond Stress to Concrete

The bond stress to concrete shown is based on pull out tests performed using test methods proposed in
ACI440 drafts. This method is used as it is easily repeatable and gives an indication of relative performance.
Forms constructed out of plywood are used to cast a concrete block around one meter long rods as shown
below.
Embedment Length

Concrete Block
FRP Rebar

Free End

Load End
Bond Breaker

In order to control the embedment length within the block, the rods are prepared with a bond breaker which
consists of soft plastic tubing placed around the rods to prevent contact between the rod and concrete.
The embedment length is 5 bar diameters.
The concrete used is a high early strength portland cement, fine aggregate (all purpose sand) and water
(49.89 kg cement, 45.36 sand and, 12.5 l water). The 14 day compressive strength of cylinders is typically 45MPa.
Previous research has shown that bond strength does not vary significantly with varying concrete strength,
provided the concrete block is properly sized to prevent splitting.
Loads are measured by the electronic load cell of a test frame and the slip between the rod & concrete is
measured by six DC voltage LVDTs, three at each end.
While the free end LVDTs measure direct indication of free end slip, the loaded end measurements need
to be adjusted for elongation of the rod between the actual loaded end of the embedment length and the
attachment point of the LVDTs.

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

Typical Load/Slide Curve for GFRP Rebar

60

Where AR is the effective cross sectional

area of the rod.
Bond Stress is calculated as
Tb =

P
Ab

Where P = Load
Ab = db Lb
db = Effective Bar Diameter
Lb = Embedment Length

20

50
40

16

30

12
Load End Slip
Free End Slip

20

10
0

Bond Stress (MPa)

Load Length
E AR

Load (KN)

Aslan 100

FIBERGLASS REBAR

Actual Slip = Measured Slip -

4
0

4
5
6
Slip (mm)

Bond of GFRP to concrete is controlled by the following internal mechanisms: chemical bond,
friction due to surface roughness of the GFRP rods, mechanical interlock of the GFRP rod against
the concrete, hydrostatic pressure against the GFRP rods due to
shrinkage of hardened concrete and swelling of GFRP rods due to
moisture absorption and temperature change. Friction and mechanical
interlock are considered to be the primary means of stress transfer.

Bond stress pull out test in fixture.

Maximum Bond Stress................................................................................ 11.6 MPa (1679 psi)

Based on pull out tests performed using the Penn State method.

IV. Coefficient of Thermal Expansion:

Transverse Direction 18.7 x 10-6/oF
33.7 x 10-6/oC
Longitudinal Direction 3.66 x 10-6/oF
6.58 x 10-6/oC
V. Barcol Hardness:
50 min. per ASTM D2583
VI. Glass Fiber Content by Weight:
70% minimum per ASTM D2584
VII. Specific Gravity:
2.0 per ASTM D792

Shear Strength Test Fixture

VIII. Shear Stress:

Shear stress measured on 5/8" diameter bars using a double
shear test fixture; 22,000 psi (152 MPa)

ASLAN 100 Fiberglass Rebar

Aslan 100

FIBERGLASS REBAR

Durability

Potential durability versus traditional steel reinforcement is one of

the chief benefits of GFRP Rebar. However, being a relatively
new material for use as a concrete reinforcement, decades of
performance data are not available. Therefore, durability or
longevity is one of the key issues concerning GFRP reinforcement.
In environments that would degrade steel reinforcement, there
is little concern that these same agents (low pH solutions) will
degrade the quality of GFRP rebar. High pH or alkaline solutions
will, however, degrade glass fibers. Research has focused on
encapsulating the glass fibers in a resin matrix that protects them
from potential alkaline degradation. Aslan 100 is produced using a
vinylester resin matrix.

Microscopy photo of Hughes Brothers

Rebar - 60 X

Typical portland concrete pour water is very alkaline with a pH

of approximately 13. It is presumed that any water that hydrates
through the concrete also creates a high pH solution that could
potentially degrade the rebar.
Most durability studies have focused on subjecting GFRP Rebars
to alkaline solutions of 13pH at elevated temperatures to simulate
service lives on the order of 50 years.
Accelerated aging bath studies performed on Hughes Brothers
GFRP rebar at Penn State University, Iowa State and Sherbrooke
in Canada, indicate that after accelerated aging, Hughes Brothers
GFRP Rebar experienced a 16% degradation in tensile strength and
a 4% change in modulus of elasticity.

Microscopy photo of Hughes

Brothers Rebar - 240 X

If used in polymer concrete, a plastic matrix, or as temporary

reinforcing in portland concrete, a separate GFRP rebar formulation,
Aslan 101, is available.

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

Aslan 100

FIBERGLASS REBAR

Creep

When subjected to a constant load, all structural materials,

including steel, may fail suddenly after a period of time,
a phenomenon known as creep rupture. Creep tests
conducted in Germany by Bundelmann & Rostasy in 1993,
indicate that if sustained stresses are limited to less than
60% of short term strength, creep rupture does not occur
in GFRP rods. For this reason, GFRP rebars are not
suitable for use as prestressing tendons. In addition,
other environmental factors such as moisture can affect
creep rupture performance.

Sierrita de la Cruz Creek Bridge,

RM1061 Amarillo Texas.

Based on ACI 440 design guidelines, sustained stress may

not exceed 20% of minimum ultimate tensile stress.

Available ACI Bends

For a summary of the recommended design guidelines, refer to

AC1440.1R-01 or your controlling national guide.

Dia.
#2
#3
#4
#5
#6
#7
#8

Stirrups, Shapes and Bends

Bends in Hughes Brothers GFRP Rebar are fabricated by shaping

over a set of molds or mandrels prior to thermoset of the resin matrix.
Field bends are not allowed.
All bends must be made at the factory.
Research has shown that bends typically maintain 38% of ultimate
tensile strength through the radius. (Eshani, Rizkalla)

Inside Bend Dia.

3"
4.25"
4.25"
4.5"
4.5"
6"
6"

Bent portions of GFRP rebars have a lower tensile

strength than straight portions.
Studies indicate that the maximum load carrying
capacity of the bent portion of GFRP rebar is 38%
of the straight bar.
It is recommended that you work with the factory in the
early stages of design, as not all standard bends and
shapes are readily available. For example, a J-Hook at
the end of a 10 meter length of rebar would be achieved
by lap splicing (40 times the diameter for splice length)
a J-hook piece to the 10 meter rebar.
The narrowest inside stirrup width is 10", (15 inches
for #7 & #8 bar).
Bends are limited to shapes that continue in the
same circular direction. Otherwise lap splices are
required.
Due to the low E Modulus of GFRP bars, it is possible
to field bend large radius shapes. Care must be taken
to avoid bending stresses that exceed the ACI440
recommendation of 20% of ultimate sustained stress in
the bar. For this reason, the minimum allowable radius for
field curved GFRP bars is shown.

ASLAN 100 Fiberglass Rebar

Some bent shapes are made using

appropriate lap splicing.

Large Radius Curves

Bar Diameter
#2 6mm
#3 9mm
#4 13mm
#5 16mm
#6 19mm
#7 22mm
#8 25mm
#9 29mm
#10 32mm

Minimum
Allowable Radius
34"
864mm
51" 1295mm
67" 1702mm
84" 2134mm
101" 2565mm
118" 2997mm
135" 3429mm
152" 3861mm
186" 4267mm

Aslan 100

FIBERGLASS REBAR

Design Considerations

In May of 2001, ACI committee 440 published

ACI440.1R-01 Guide for the Design an
Construction of Concrete Reinforced with FRP
Bars. Revision of this Emerging Technology
Series document will occur on a regular basis.
To date, this represents the most authoritative
guide on the subject of FRP reinforced
concrete design.
The designer should understand that a direct
substitution between GFRP and steel rebar is
not possible due to various differences in the
mechanical properties of the two materials.

One difference is that all FRPs are linear elastic up to failure and
exhibit no ductility or yielding. In traditional steel reinforced concrete
design, a maximum amount of steel is specified so that the steel will
yield and give warning of pending failure of the concrete member.
ACI440.1R-01 gives the option of two failure modes to the designer,
an over reinforced section where compression failure of the concrete
is the preferred mode of failure. Or, failure by rupture of the FRP
reinforcing in which case serviceability requirements, deflection and
crack widths, must be satisfied in order to give a warning of pending
failure. In either case, the suggested margin of safety against failure is
higher than that used in traditional steel-reinforced concrete design.

Test beam at Purdue University.

Another major difference is that serviceability will be more of a design

limitation in GFRP reinforced members than with steel. Due to it's
lower modulus of elasticity, deflection and crack widths will affect the
design.
Outside of North America, the ASCE Journal of Composites has
published design guidelines for GFRP Reinforced Concrete for
Construction (Aug 1997 Vol.1 No 3 ISSN 1090-0268 Code: JCCOF2)
based on the extensive work performed in Japan for the Japanese
Ministry of Construction. Additional design guidelines have been
published by the Canadian Highway Bridge Design Code; Section
16 Fibre Reinforced Structures and Commentary for Section 16.
Modifications to Norwegian Standard NS3473 when using fiber
reinforced plastic (FRP) reinforcement, April 29, 1998. From the
United Kingdom, the Institution of Structural Engineers, Interim
Guidance on the Design of Reinforced Concrete Structures Using
Fibre Composite Reinforcement, August 1999. Active efforts are
also underway for a European Eurocode 2 under the efforts of FIB
Task Group 9.3 FRP (Fibre Reinforced Polymer) Reinforcement for
Concrete Structures. Links to many of these activities can be found
via the Hughes Brothers web site.

Concrete strain gauge for long term

monitoring.

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

Aslan 100

FIBERGLASS REBAR

Hughes Brothers only guarantees the performance of its material

to meet minimum ultimate requirements as listed. The use of
competent experienced engineering personnel should always be
employed in the design and construction of concrete reinforced
structures.
Subjects covered in the ACI440.1R-01 design guide include:
Flexure
Shear
Temperature and Shrinkage Reinforcement
Development Length and Splices
Current knowledge restricts the use of FRP bars for:
Compression Reinforcement in both beams and columns
Seismic Zones
Moment Frames
Zones where moment redistribution is required
Structures subject to high temperature

Traditional construction methods are used.

Lap Splice - Tension

Approximately 40 bar diameters should be used for GFRP v.s.
30 bar diameter for steel (grade 60ksi, less than #6 diameter.)

Light weight of GFRP rebar aids

installation.

Plastic coated wire ties are recommended.

Nylon zip-ties may be used for completely
non-magnetic applications.

ASLAN 100 Fiberglass Rebar

10

Design Assistance and Software Available

Aslan 100

FIBERGLASS REBAR

To aid the designer unfamiliar with the new

ACI440.1R-01 guide, Hughes Brothers maintains
a close working relationship with an independent
engineering firm specializing in the use of
FRP named CoForce (Composites for Civil
Engineering). Design assistance or verification
is available from CoForce whose personnel are
recognized worldwide as leading authorities in the
implementation of all types of FRP reinforcing.

Additionally, a design software implementation of ACI440.1R-01 is available upon request to aid in

performance of reinforced concrete design per the latest ACI publications for FRP bars. The software modules
are based in MathCad.

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

11

Aslan 100

FIBERGLASS REBAR

Masonry Strengthening
Aslan 100 GFRP bars can be used to increase the strength of existing unreinforced
masonry walls in flexure (out-of-plane) and shear (in-plane).
This has important implications in areas that are subject to new seismic codes, hurricane
wind loading or even blast mitigation schemes. In addition, Aslan 100 GFRP bars can
be used to restore or increase the structural strength of existing masonry walls that have
already cracked.
In many instances the strengthening procedure can maintain the visual appearance of the
existing masonry, particularly in the case of shear reinforcing.

The technique used is known as Near Surface Mount or NSM strengthening. The procedure
consists of:
1) grooving of slots having a width and depth of approximately 1.5 times the bar diameter,
2) cleaning the groove,
3) applying a structural epoxy or cementitious based paste into the groove,
4) insertion of the GFRP bar in the groove,
5) finishing for appearance.

ASLAN 100 Fiberglass Rebar

12

Aslan 100

FIBERGLASS REBAR

If hollow Concrete Masonry Units

(CMU) are being strengthened, the
groove depth should not exceed
the thickness of the masonry unit
shell to avoid local fracture of the
masonry. It is also recommended
to mask off the groove to avoid
staining the surrounding masonry
during the application of epoxy or
cementitious pastes.

Example: Masonry Strengthening

The following example describes how Aslan 100 GFRP bars would be used to strengthen
a portion of the cracked masonry of a retail store. The nature of the damage is shown in
Figure 1. The proposal was prepared by CoForce International Consultants.

Wall A (Outside)
Wall B (Outside)

Figure 1 Damage in Masonry Wall

A possible interpretation of the damage is given in the following section.

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

13

Aslan 100

FIBERGLASS REBAR

Assessment of the Damage

Analyzing the pictures provided by the engineer of record, the following can be drawn:
A crack is visible in the masonry wall labeled A (see Figure 1), and it is limited to the

corner portion of the wall. Its length is roughly 15-16 ft;

The crack terminates when it meets the horizontal steel beam supporting the wall labeled

as B shown in Figure 2;

The steel truss supporting the roof of the building is sitting along the wall B (Figure 3);
A construction joint is present on Wall B as depicted in Figure 2; thus, only the right

portion of Wall B represented in the same figure will be strengthened without interfering
with the remaining part of the wall.
Wall B (Inside)
Wall A (Inside)
Construction
Joint

Steel 1 Beam

Figure 2 Steel Beam Supporting Wall B

Steel Beam

Wall B (Inside)

Wall A (Inside)

Figure 3 Steel Truss Supporting the Roof

ASLAN 100 Fiberglass Rebar

14

Aslan 100

Repair Technique
The use of Near Surface Mounted (NSM) FRP technology in masonry structures consists
of placing a bar in a groove cut into the existing mortar joint of the member being
strengthened. The FRP bar is embedded in an epoxy-based paste which transfers stresses
between the masonry unit and the bar. The groove is first half-filled with the paste; then the
bar is inserted and slightly pressed to force the paste to embed the bar. As a last step, the
groove is completely filled with paste and the surface leveled. A sketch of completed work
is given in Figure 4.

FIBERGLASS REBAR

The crack formation is probably due to the movements of the steel truss supporting the roof
of the building caused by thermal expansion. Due to the presence of the construction joint,
only the truss represented in Figure 3 should be responsible for the movement of Wall B
which, in turn, leads to the crack formation visible on Wall A.

Figure 4 Detail of NSM FRP Installation

Advantages of using composites in conjunction with NSM technology include low

installation cost, high corrosion resistance, unnoticeable changes in the member sizes, and
minimized disturbance to the occupants of the facility. In Figure 5 a recent application of
NSM technique to restore the flexural capacity of cracked walls is shown.

Figure 5 Flexural Strengthening of Unreinforced Masonry Wall

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

15

Aslan 100

FIBERGLASS REBAR

Shop Drawings
Based on this preliminary assessment of the wall conditions, both walls need to be
strengthened using horizontal FRP bars to be placed in the mortar joints, as shown in
Figure 6 and Figure 7 for Walls A and B, respectively. A plan view of the installation is
shown in Figure 8, while Figure 9 shows details for each type of bar being used.

Figure 6 Wall Type A (FRP Bars are shown as Blue Lines)

ASLAN 100 Fiberglass Rebar

16

Aslan 100

FIBERGLASS REBAR

Figure 7 Wall Type B (FRP Bars are shown as Blue Lines)

Figure 8 Plan View of the Strengthened Walls (FRP Bars are shown as Blue Lines)

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

17

Aslan 100

FIBERGLASS REBAR

Figure 9 Detail of FRP Bar Placement (FRP Bars are shown as Blue Lines)

Bar Type B

Bar Type A

Bar Type C
ASLAN 100 Fiberglass Rebar

18

Aslan 100

FIBERGLASS REBAR

Handling and Placement

When necessary, cutting of GFRP rebars should be done
with a masonry or diamond blade, grinder or fine blade saw.
A dust mask is suggested when cutting the bars. It is
recommended that work gloves be worn when handling and
placing GFRP rebars.
Sealing of cut ends is not necessary since any possible
wicking will not ingress more than a small amount into the
end of a rod.
GFRP rebar has a very low specific gravity and may
float in concrete during vibration. Care should be exercised
to adequately secure GFRP in formwork using chairs, plastic
coated wire ties or nylon zip ties.

Traditional rebar chairs are used but with

greater frequency. ie. 2/3 rds spacing used
with steel.

Quality Assurance
To provide for lot or production run traceability, each lot is
color coded.
Individual rebars are tensile tested based on a random
statistical sampling, with a minimum of 5 samples tested per
prodution lot.
Certifications of conformance are available for any given
production lot.
In addition, quality assurance tests are routinely performed
to determine:
- Glass content - i.e. impregnation ASTM D2584
- Die wicking - checking for voids ASTM D5117
- Barcol hardness ASTM D2583
- Cross sectional area ACI 440-K
- Mass uptake in water ASTM D570
- Inter-laminear shear or shear in flexure ASTM D4475
- Shear strength of #5 diameter bars by double shear
method. ACI 440-F

Cutting should be done with fine blade saw,

masonry, diamond blade or grinder. Shearing
is NOT permitted.

Moisture uptake testing in lab.

Hughes Brothers, Inc.

Phone: 800-869-0359
402-643-2991
210 N. 13 Street
Fax:
402-643-2149
Seward, NE 68434
www.hughesbros.com
Email: [email protected]
th

December 2002

19

Aslan 100

FIBERGLASS REBAR
2002

Hughes Brothers, Inc.

210 North 13th Street
Seward, Nebraska 68434
Phone 800.869.0359 or 402.643.2991 / Fax 402.643.2149
www.hughesbros.com