Telemark

University College
Department of Electrical Engineering, Information Technology and Cybernetics

Introduction to LabVIEW
HANS-PETTER H ALVORSEN, 2 014.03.07

Faculty of Technology,

Postboks 203, Kjlnes ring 56, N-3901 Porsgrunn, Norway.

Tel: +47 35 57 50 00

Fax: +47 35 57 54 01

Preface
This document explains the basic concepts of LabVIEW.
You find additional resources, code, etc. here:
http://home.hit.no/~hansha/?tutorial=labview

You need to install the LabVIEW Professional Development System.

For more information about LabVIEW, visit my Blog: http://home.hit.no/~hansha/

ii

Table of Contents
Preface ....................................................................................................................................... ii
Table of Contents ...................................................................................................................... iii
1 Introduction ........................................................................................................................ 1
1.1 Dataflow Programming ................................................................................................ 1
1.2 Graphical Programming ............................................................................................... 1
1.3 Benefits ........................................................................................................................ 2
2 Start using LabVIEW ............................................................................................................ 4
2.1 The LabVIEW Environment .......................................................................................... 4
2.2 Front Panel .................................................................................................................. 5
2.3 Block Diagram .............................................................................................................. 7
2.4 Controls Palette ......................................................................................................... 10
2.4.1 Numeric Sub Palette ........................................................................................... 12
2.4.2 Boolean Sub Palette ............................................................................................ 13
2.4.3 String & Path Sub Palette .................................................................................... 13
2.5 Function Palette ......................................................................................................... 13
2.6 Tools Palette .............................................................................................................. 14
2.7 Wiring ........................................................................................................................ 16
2.8 Toolbar ....................................................................................................................... 16
2.9 Execution ................................................................................................................... 17
2.10 The Objects short-cut menu .................................................................................... 18
2.11 Dataflow Programming ........................................................................................... 19
2.12 Help ......................................................................................................................... 20
Exercises ............................................................................................................................. 20
iii

iv

Table of Contents

3 Sub VIs .............................................................................................................................. 24

3.1 Create New Sub VI from Scratch ................................................................................ 26
3.1.1 Input and Output SubVI Connectors ................................................................... 26
3.1.2 Icon Editor ........................................................................................................... 28
3.2 Create Sub VI from existing code ............................................................................... 29
3.3 Using Sub VIs ............................................................................................................. 30
Exercises ............................................................................................................................. 31
4 Customize LabVIEW .......................................................................................................... 33
Exercises ............................................................................................................................. 34
5 Loops and Structures ........................................................................................................ 35
5.1 Loops ......................................................................................................................... 35
5.1.1 For Loop .............................................................................................................. 36
5.1.2 While Loop .......................................................................................................... 37
5.2 Structures .................................................................................................................. 38
5.2.1 Case Structure ..................................................................................................... 38
5.2.2 Sequence Structure ............................................................................................ 39
5.2.3 Event Structure ................................................................................................... 40
Exercises ............................................................................................................................. 42
6 Troubleshooting and Debugging ...................................................................................... 45
6.1 How to find errors ..................................................................................................... 45
6.2 Highlight Execution .................................................................................................... 45
6.3 Probes ........................................................................................................................ 46
6.4 Breakpoints ................................................................................................................ 47
6.5 Step into/over/out debugging ................................................................................... 48
Exercises ............................................................................................................................. 49

Tutorial: An Introduction to LabVIEW

Table of Contents

7 Working with Data ............................................................................................................ 51

7.1 Arrays ......................................................................................................................... 51
7.1.1 Auto-Indexing ..................................................................................................... 51
7.1.2 Array Functions ................................................................................................... 52
7.2 Cluster ........................................................................................................................ 54
7.2.1 Cluster Order ...................................................................................................... 55
7.2.2 Cluster Elements ................................................................................................. 56
Exercises ............................................................................................................................. 57
8 Working with Strings ........................................................................................................ 59
Exercises ............................................................................................................................. 61
9 Error Handling ................................................................................................................... 63
9.1 Finding Error .............................................................................................................. 63
9.2 Error Wiring ............................................................................................................... 63
9.3 Error Handling in SubVIs ............................................................................................ 64
9.4 Error Handling ............................................................................................................ 65
Exercises ............................................................................................................................. 66
10 Working with Projects .................................................................................................... 67
10.1 Project Explorer ....................................................................................................... 67
10.2 Deployment ............................................................................................................. 68
Exercises ............................................................................................................................. 71
11 Design Techniques .......................................................................................................... 72
11.1 Force Program Flow ................................................................................................. 72
11.2 Shift Register ........................................................................................................... 73
11.3 State Programming Architecture ............................................................................. 74
11.4 Multiple Loops/Parallel programming ..................................................................... 77

Tutorial: An Introduction to LabVIEW

vi

Table of Contents

11.5 Templates ................................................................................................................ 78

Exercises ............................................................................................................................. 80
12 User Interface ................................................................................................................. 83
12.1 VI Properties ............................................................................................................ 84
Exercises ............................................................................................................................. 87
13 Plotting Data ................................................................................................................... 88
13.1 Customizing ............................................................................................................. 90
Exercises ............................................................................................................................. 92
14 Tips & Tricks .................................................................................................................... 94
14.1 10 functions you need to know about ..................................................................... 94
14.2 The 10 most useful Short-cuts ................................................................................. 99
15 Example Application ..................................................................................................... 100
16 Additional Exercises ...................................................................................................... 105
17 Whats Next? ................................................................................................................ 110
17.1 My Blog .................................................................................................................. 110
17.2 Training .................................................................................................................. 110
17.3 Additional Resources ............................................................................................. 110
17.4 Examples ................................................................................................................ 110
17.5 Documentation ...................................................................................................... 111
17.6 LabVIEW Wiki ........................................................................................................ 112
17.7 LabVIEW on YouTube ............................................................................................ 112
Quick Reference .................................................................................................................... 113

Tutorial: An Introduction to LabVIEW

1 Introduction
LabVIEW (short for Laboratory Virtual Instrumentation Engineering Workbench) is a
platform and development environment for a visual programming language from National
Instruments. The graphical language is named "G". Originally released for the Apple
Macintosh in 1986, LabVIEW is commonly used for data acquisition, instrument control, and
industrial automation on a variety of platforms including Microsoft Windows, various flavors
of UNIX, Linux, and Mac OS X. The latest version of LabVIEW is version LabVIEW 2011. Visit
National Instruments at www.ni.com.
The code files have the extension .vi, which is an abbreviation for Virtual Instrument.
LabVIEW offers lots of additional Add-Ons and Toolkits.

1.1 Dataflow Programming

The programming language used in LabVIEW, also referred to as G, is a dataflow
programming language. Execution is determined by the structure of a graphical block
diagram (the LV-source code) on which the programmer connects different function-nodes
by drawing wires. These wires propagate variables and any node can execute as soon as all
its input data become available. Since this might be the case for multiple nodes
simultaneously, G is inherently capable of parallel execution. Multi-processing and
multi-threading hardware is automatically exploited by the built-in scheduler, which
multiplexes multiple OS threads over the nodes ready for execution.

1.2 Graphical Programming

LabVIEW ties the creation of user interfaces (called front panels) into the development cycle.
LabVIEW programs/subroutines are called virtual instruments (VIs). Each VI has three
components: a block diagram, a front panel, and a connector panel. The last is used to
represent the VI in the block diagrams of other, calling VIs. Controls and indicators on the
front panel allow an operator to input data into or extract data from a running virtual
instrument. However, the front panel can also serve as a programmatic interface. Thus a
virtual instrument can either be run as a program, with the front panel serving as a user
interface, or, when dropped as a node onto the block diagram, the front panel defines the
inputs and outputs for the given node through the connector pane. This implies each VI can
be easily tested before being embedded as a subroutine into a larger program.
1

Introduction

The graphical approach also allows non-programmers to build programs simply by dragging
and dropping virtual representations of lab equipment with which they are already familiar.
The LabVIEW programming environment, with the included examples and the
documentation, makes it simple to create small applications. This is a benefit on one side,
but there is also a certain danger of underestimating the expertise needed for good quality
"G" programming. For complex algorithms or large-scale code, it is important that the
programmer possess an extensive knowledge of the special LabVIEW syntax and the
topology of its memory management. The most advanced LabVIEW development systems
offer the possibility of building stand-alone applications. Furthermore, it is possible to create
distributed applications, which communicate by a client/server scheme, and are therefore
easier to implement due to the inherently parallel nature of G-code.

1.3 Benefits
One benefit of LabVIEW over other development environments is the extensive support for
accessing instrumentation hardware. Drivers and abstraction layers for many different types
of instruments and buses are included or are available for inclusion. These present
themselves as graphical nodes. The abstraction layers offer standard software interfaces to
communicate with hardware devices. The provided driver interfaces save program
development time. The sales pitch of National Instruments is, therefore, that even people
with limited coding experience can write programs and deploy test solutions in a reduced
time frame when compared to more conventional or competing systems. A new hardware
driver topology (DAQmxBase), which consists mainly of G-coded components with only a
few register calls through NI Measurement Hardware DDK (Driver Development Kit)
functions, provides platform independent hardware access to numerous data acquisition
and instrumentation devices. The DAQmxBase driver is available for LabVIEW on Windows,
Mac OS X and Linux platforms.
This document introducing the following themes:

Start using LabVIEW

o The LabVIEW Environment
o Front Panel and Block Diagram
o Palettes: Control Palette, Functions Palette, Tools Palette
o Data Types
o Property Nodes
Sub VIs
Loops and Structures
Troubleshooting and Debugging
Tutorial: An Introduction to LabVIEW

Introduction

Working with Data

o Arrays
! Array Functions
o Cluster
Working with Strings
Error Handling
Working with Projects using Project Explorer
Design Techniques
o Shift Register
o State Machine
o Multiple Loops
User Interface
Plotting Data
Deployment: Building Executable Applications (.exe)
Introduction to Add Ons and Toolkits
o Briefly explanations
o More detail about Control and Simulation Toolkit in later chapter
Introduction to DAQ - Data Acquisition
o MAX Measurement and Automation Explorer
o NI-DAQmx
Quick Reference with Keyboard Short-cuts

For more information about LabVIEW, visit my Blog: http://home.hit.no/~hansha/

Tutorial: An Introduction to LabVIEW

2 Start using LabVIEW

This chapter explains the basic concepts in LabVIEW.
The topics are as follows:

The LabVIEW Environment

Front Panel and Block Diagram
Palettes: Control Palette, Functions Palette, Tools Palette
Data Types
Property Nodes

2.1 The L abVIEW E nvironment

LabVIEW programs are called Virtual Instruments, or VIs, because their appearance and
operation imitate physical instruments, such as oscilloscopes and multimeters. LabVIEW
contains a comprehensive set of tools for acquiring analyzing, displaying, and storing data, as
well as tools to help you troubleshoot your code.
When opening LabVIEW, you first come to the Getting Started window.

Start using LabVIEW

In order to create a new VI, select Blank VI or in order to create a new LabVIEW project,
select Empty project.
When you open a blank VI, an untitled front panel window appears. This window displays
the front panel and is one of the two LabVIEW windows you use to build a VI. The other
window contains the block diagram. The sections below describe the front panel and the
block diagram.

2.2 Front P anel

When you have created a new VI or selected an existing VI, the Front Panel and the Block
Diagram for that specific VI will appear.

In LabVIEW, you build a user interface, or front panel, with controls and indicators. Controls
are knobs, push buttons, dials, and other input devices. Indicators are graphs, LEDs, and
other displays.
You build the front panel with controls and indicators, which are the interactive input and
output terminals of the VI, respectively. Controls are knobs, push buttons, dials, and other
input devices. Indicators are graphs, LEDs, and other displays. Controls simulate instrument
Tutorial: An Introduction to LabVIEW

Start using LabVIEW

input devices and supply data to the block diagram of the VI. Indicators simulate instrument
output devices and display data the block diagram acquires or generates.
E.g., a Numeric can either be a Numeric Control or a Numeric Indicator, as seen below.

I you select a Numeric Control, it can easy be changed to an Numeric Indicator by right
click on the object an select Change to Indicator

Or opposite, I you select a Numeric Indicator, it can easy be changed to an Numeric
Control by right click on the object an select Change to Control

Tutorial: An Introduction to LabVIEW

Start using LabVIEW

The difference between a Numeric Control and a Numeric Indicator is that for a
Numeric Control you may enter a value, while the Numeric Indicator is read-only, i.e.,
you may only read the value, not change it.

The appearance is also slightly different, the Numeric Control has an increment and an
decrement button in front, while the Numeric Indicator has a darker background color in
order to indicate that its read-only.

2.3 Block D iagram

After you build the user interface, you add code using VIs and structures to control the front
panel objects. The block diagram contains this code. In some ways, the block diagram
resembles a flowchart.
Tutorial: An Introduction to LabVIEW

Start using LabVIEW

After you build the front panel, you add code using graphical representations of functions to
control the front panel objects. The block diagram contains this graphical source code. Front
panel objects appear as terminals, on the block diagram. Block diagram objects include
terminals, subVIs, functions, constants, structures, and wires, which transfer data among
other block diagram objects.
The Figure below shows a front panel and its corresponding block diagram with front panel
and block diagram components.

Tutorial: An Introduction to LabVIEW

Start using LabVIEW

The different components are as follows:
1. Toolbar
2. Owned Label
3. Numeric Control
4. Free Label
5. Numeric Control Terminal
6. Knob Terminal
7. Numeric Constant
8. Multiply Function
9. Icon
10. Knob Control
Tutorial: An Introduction to LabVIEW

10

Start using LabVIEW

11. Plot Legend

12. XY Graph
13. Wire Data Path
14. XY Graph Terminal
15. Bundle Function
16. SubVI
17. For Loop Structure

2.4 Controls P alette

The Controls and Functions palettes contain sub palettes of objects you can use to create a
VI. When you click a sub palette icon, the entire palette changes to the sub palette you
selected. To use an object on the palettes, click the object and place it on the front panel or
block diagram. The Controls palette is available only on the front panel. The Controls palette
contains the controls and indicators you use to build the front panel.

Tutorial: An Introduction to LabVIEW

11

Start using LabVIEW

The most used Sub Palettes are the Numeric Sub Palette, the Boolean Sub Palette and the
String & Path Sub Palette.
You may change the appearance and the contents of the Controls palette:
You may Pin the palette, so it is always visible, just click the little pin button
upper left corner of the palette:

in the

If you want to change the content and appearance of the palette, click the View button.

Here you may change the way the palette should look.

If you click Change Visible Categories you may change which Categories you want to have
visible.

Tutorial: An Introduction to LabVIEW

12

Start using LabVIEW

2.4.1

Numeric S ub P alette

Numerical Control and Numerical Indicator are the most used objects in the numeric sub
palette.

Tutorial: An Introduction to LabVIEW

13

2.4.2

Start using LabVIEW

Boolean S ub P alette

This palette has lots of different buttons you may use. OK, Cancel and Stop buttons are
useful.

2.4.3

String & P ath S ub P alette

In the String and Path palette we have String Controls, Combo Box, etc.

2.5 Function P alette

Tutorial: An Introduction to LabVIEW

14

Start using LabVIEW

The Functions palette is available only on the block diagram. The Functions palette contains
the VIs and functions you use to build the block diagram.

2.6 Tools P alette

You can create, modify, and debug VIs using the tools located on the floating Tools palette.
The Tools palette is available on both the front panel and the block diagram. A tool is a
special operating mode of the mouse cursor. The cursor corresponds to the icon of the tool
selected in the Tools palette. Use the tools to operate and modify front panel and block
diagram objects.

Tutorial: An Introduction to LabVIEW

15

Start using LabVIEW

The Tools palette is available from the View menu:

If you make sure Automatic wiring is disabled (I recommend you do so!) you may use
the Tab key on your keyboard in order to switch between the most common tools.
The most used tools are:
Use the Operating tool, shown at left, to change the values of a control or select
the text within a control. The Operating tool changes to the icon shown at left when it
moves over a text control, such as a numeric or string control.
Use the Positioning tool, shown at left, to select, move, or resize objects. The
Positioning tool changes to resizing handles when it moves over the edge of a resizable
object.
Use the Labeling tool, shown at left, to edit text and create free labels. The
Labeling tool changes to the following icon

when you create free labels.

Use the Wiring tool, shown at left, to wire objects together on the block diagram.
Tutorial: An Introduction to LabVIEW

16

Start using LabVIEW

2.7 Wiring
In order to create the logical flow between the object on the Block Diagram, you need to use
the Wiring tool in order to connect the different objects together.
Use the Wiring tool to wire objects together on the block diagram.
Available Keyboard Shortcuts when dealing with Wiring:

Ctrl-B is very useful. This short-cut removes all broken wires on the Block Diagram.

2.8 Toolbar
Below we see the LabVIEW Toolbar:

Tutorial: An Introduction to LabVIEW

17

Start using LabVIEW

The behaviors of the different buttons are as follows:

Click the Run button to run a VI. LabVIEW compiles the VI, if necessary. You can run a VI
if the Run button appears as a solid white arrow. The solid white arrow, shown above, also
indicates you can use the VI as a subVI if you create a connector pane for the VI.
While the VI runs, the Run button appears as shown at left if the VI is a top-level VI,
meaning it has no callers and therefore is not a subVI.
If the VI that is running is a subVI, the Run button appears as shown at left.
The Run button appears broken, shown at left, when the VI you are creating or editing
contains errors. If the Run button still appears broken after you nish wiring the block
diagram, the VI is broken and cannot run. Click this button to display the Error list window,
which lists all errors and warnings.
Click the Run Continuously button, shown at left, to run the VI until you abort or pause
execution. You also can click the button again to disable continuous running.
While the VI runs, the Abort Execution button, shown at left, appears. Click this button
to stop the VI immediately if there is no other way to stop the VI. If more than one running
top-level VI uses the VI, the button is dimmed.
Note: Avoid using the Abort Execution button to stop a VI. Either let the VI complete its data
ow or design a method to stop the VI programmatically. By doing so, the VI is at a known
state. For example, place a button on the front panel that stops the VI when you click it.
Click the Pause button, shown at left, to pause a running VI. When you click the Pause
button, LabVIEW highlights on the block diagram the location where you paused execution,
and the Pause button appears red. Click the button again to continue running the VI.

2.9 Execution
In addition to the Toolbar buttons above the following Keyboard Shortcuts are available
when dealing with Execution:

Tutorial: An Introduction to LabVIEW

18

Start using LabVIEW

2.10

The O bjects s hort-cut m enu

The most often-used menu is the object shortcut menu. All LabVIEW objects and empty
space on the front panel and block diagram have associated shortcut menus. Use the
shortcut menu items to change the look or behavior of front panel and block diagram
objects. To access the shortcut menu, right-click the object, front panel, or block diagram.
The Numeric control has the following short-cut/right-click menu:

Tutorial: An Introduction to LabVIEW

19

Start using LabVIEW

The short-cut menu will be different for the different controls or objects.

2.11

Dataflow P rogramming

LabVIEW follows a dataflow model for running VIs. A block diagram node executes when all
its inputs are available. When a node completes execution, it supplies data to its output
terminals and passes the output data to the next node in the dataflow path.
Visual Basic, C++/C#, Java, and most other text-based programming languages follow a
control flow model of program execution. In control flow, the sequential order of program
elements determines the execution order of a program.

Example: Dataflow Programming

The Example shows a block diagram that adds two numbers and then subtracts 50.00 from
the result of the addition. In this case, the block diagram executes from left to right, not
because the objects are placed in that order, but because the Subtract function cannot
execute until the Add function finishes executing and passes the data to the Subtract
function. Remember that a node executes only when data are available at all of its input
terminals, and it supplies data to its output terminals only when it finishes execution.
Example: Dataflow Programming

Tutorial: An Introduction to LabVIEW

20

Start using LabVIEW

In this example, consider which code segment would execute first-the Add, Random
Number, or Divide function. You cannot know because inputs to the Add and Divide
functions are available at the same time, and the Random Number function has no inputs. In
a situation where one code segment must execute before another and no data dependency
exists between the functions, use other programming methods, such as error clusters, to
force the order of execution.

2.12

Help

The Context Help window (Ctrl +H) displays basic information about LabVIEW objects
when you move the cursor over each object. The Context Help window is visible by default.
To toggle display of the Context Help window, select Help-Show Context Help, press the
Ctrl-H keys, or click the Show Context Help Window button on the toolbar.
When you move the cursor over front panel and block diagram objects, the Context Help
window displays the icon for subVIs, functions, constants, controls, and indicators, with
wires attached to each terminal. When you move the cursor over dialog box options, the
Context Help window displays descriptions of those options. In the window, required
connections are bold, recommended connections are plain text, and optional connections
are dimmed or do not appear. The Figure below shows an example of the Context Help
window.

Exercises
Exercise: Create your first LabVIEW application (VI)

Tutorial: An Introduction to LabVIEW

21

Start using LabVIEW

Create a simple LabVIEW application (VI) with a Front Panel with some Controls and
Indicators. Create the logic by connecting the Terminals on the Block Diagram
The Front Panel could look something like this:

The Block Diagram could look something like this:

Start the program with the Run button.

Exercise: Create a simple Calculator
Create a simple calculator that Add and Subtract 2 numbers like this:

Tutorial: An Introduction to LabVIEW

22

Start using LabVIEW

Start the program with the Run button.

Exercise: Write Data to File
Create a VI that writes data to a Text File.
Use Vis or functions from the File I/O palette

The program could look something like this:

Tutorial: An Introduction to LabVIEW

23

Start using LabVIEW

Exercise: Read Data from File
Create another VI that read the text file you created in the previous VI.

Tutorial: An Introduction to LabVIEW

3 Sub VIs
This chapter explains the basic concepts of creating and using Sub VIs in LabVIEW.
Topics:

Create New Sub VI from Scratch

Create Sub VI from existing code
Using Sub VIs

When you place a VI on the block diagram, LabVIEW considers the VI to be a subVI. When
you double-click a subVI, its front panel and block diagram appear, rather than a dialog box
in which you can configure options. The front panel includes controls and indicators. The
block diagram includes wires, front panel icons, functions, possibly subVIs, and other
LabVIEW objects. The upper right corner of the front panel and block diagram displays.
Below we see an example of a bad Block Diagram. This example does not make use of the
SubVI functionality in LabVIEW at all! This makes the Block diagram hard to read and
understand. The size of the diagram is also too large! The Block Diagram should always fit
into the screen. Both the Front Panel and the Block Diagram should fit into a screen
resolution of 1024x768.

24

25

Sub VIs

With use of SubVIs, the example above could turn into, e.g.:

As you can see, much of the code in the Main VI have been replaced and put into SubVIs.
The program is now more readable.
Another approach is to use a so-called State Machine principle (more about this in chapter
11 - Design Techniques ).

Available Keyboard Shortcuts when dealing with Sub Vis:

Tutorial: An Introduction to LabVIEW

26

Sub VIs

3.1 Create N ew S ub V I f rom S cratch

Select Blank VI in the Getting Started window when opening LabVIEW, or when LabVIEW
is already opened select File New V or use the short-cut Ctrl+N.

3.1.1

Input a nd O utput S ubVI C onnectors

Most SubVIs will have input and output connectors. This is similar with functions or
methods in other programming language that have input arguments and an output/result.
In order to create connectors, Right-click on the icon in the upper right corner of the VI and
select Show Connector.

You may select different Patterns, i.e., how many input and output connectors you need.

Tutorial: An Introduction to LabVIEW

27

Sub VIs

Make sure you select a Pattern with enough connectors even if you dont need all the
connectors at the moment. I recommend that you standardize on the pattern in the Figure
above.
Select the Wire tool and click on the wanted connector, then click on the Control or
Indicator on the Front Panel you want to connect to this connector.

You should always follow these connector rules:

Upper left connector: Reference In

Upper right connector: Reference Out
Lower left connector: Error In Cluster
Lower right connector: Error Out Cluster

Example: SubVI Connectors

See example below about these connector rules:

Tutorial: An Introduction to LabVIEW

28

Sub VIs

Most common VIs that exits follow these rules, see example below.

If you follow these connector rules its much easier to create a clean and neat code like this:

By doing this its also clear how the Data flows in the program. It should always flow from
left to right.

3.1.2

Icon E ditor

You should also create a suitable icon for your SubVI.

Tutorial: An Introduction to LabVIEW

29

Sub VIs

In order to open the Icon Editor, double-click on the icon in the upper right corner of your VI.

Below we see a block diagram with SubVIs icon appearance created with the Icon Editor.

3.2 Create S ub V I f rom e xisting c ode

If you find out that you code is getting messy, you could consider put some code into a
SubVI.

Tutorial: An Introduction to LabVIEW

30

Sub VIs

The procedure is as follows:

1.
2.
3.
4.
5.

Select the part of your code you want to turn into a SubVI
From the Edit menu, select Create SubVI
LabVIEW will automatically create a SubVI for the selected code.
Clean up automatically created wires, etc.
Create a suitable icon for your SubVI

Although this is quite easy to do this, I do not recommend that you use this functionality to
much. This is because you should create and use SubVIs from the first moment you start
creating your application and not afterwards when you find out that you have been creating
a messy code.
So you should structure and design your code with the use of SubVIs from the beginning!

3.3 Using S ub V Is
Below we see an example of how to use SubVIs in a program (Top VI or SubVIs):

Tutorial: An Introduction to LabVIEW

31

Sub VIs

You may open a SubVI from the File menu, select a SubVI from the Functions palette or use
drag and drop in different ways, e.g., you may drag a VI from the File Explorer in Windows
directly into an existing VI you have already opened in LabVIEW

Exercises
Exercise: Convert C to F VI
Create a SubVI that convert a Temperature in Celsius to a Temperature in Fahrenheit

1.
2.
3.
4.

Create the SubVI

Create the Front Panel and the Block Diagram as shown above
Create necessary Connectors
Create a suitable icon, e.g.:

5. Use the SubVI in another VI
6. Run the program to see if it works
7. Expand the program so you can select if you want to convert from Celsius to
Fahrenheit or from Fahrenheit to Celsius

Tutorial: An Introduction to LabVIEW

32

Sub VIs

Exercise: Convert existing code into a SubVI
Convert a part of your application into a SubVI by using the Create SubVI function in
LabVIEW.

Tutorial: An Introduction to LabVIEW

4 Customize LabVIEW
LabVIEW has lots of possibilities for customizing the appearance and the use of the LabVIEW
environment. Select Options from the Tools menu.

The default settings is not necessary the best, here are some recommendations for setting
up the LabVIEW environment.
Category: Block Diagram

33

34

Customize LabVIEW

Disable Enable auto wiring option. This prevents LabVIEW from automatically
connecting adjacent blocks. Although it seems useful to have auto wiring enables, it
is my experience that the auto wiring is a little annoying since it tends to draw wires
between blocks when you do not want any wire.
Disable Place front panel elements as icons option. This causes LabVIEW to use
small terminal icons on the block diagram. If you, instead, activate this option, the
terminal icons are larger, with a mimic of the element as it appears at the front
panel.

Category: Controls/Functions Palettes

In the Format list: select Category (Icons and Text)

Category: Alignment Grid

Turn off Show Front Panel Grid and Show Block Diagram Grid

Exercises
Exercise: Customize LabVIEW
Try the different settings explained in this chapter. Turn them on and off and watch the
different.

Tutorial: An Introduction to LabVIEW

5 Loops and Structures

This chapter explains the basic concepts of Loops and Structures in LabVIEW.
The topics are as follows:

For Loop
While Loop
Case Structure
Sequence Structure
Event Structure

The different Loops and Structures available are located in the Structures sub palette in
the Functions palette on the Block Diagram.

5.1 Loops
The most important loops are:

For Loop
While Loop
35

36

Loops and Structures

These loops will be explained in detail below.

5.1.1

For L oop

A For Loop executes a sub diagram a set number of times. The Figure below shows an empty
For Loop in LabVIEW.

A For loop executes its sub diagram n times, where n is the value wired to the count ( )
terminal. The iteration ( ) terminal provides the current loop iteration count, which ranges
from 0 to n-1.
After you create a For Loop, you can use shift registers to pass values from one iteration to
the next. If you wire an array to a For Loop, you can read and process every element in that
array by enabling auto-indexing. You also can enable auto-indexing by configuring a For
Loop to return an array of every value generated by the loop.
You can add a conditional terminal to configure a For Loop to stop when a Boolean
condition or an error occurs. A For Loop with a conditional terminal executes until the
condition occurs or until all iterations complete, whichever happens first. To add a
conditional terminal to a For Loop, right-click the For Loop border and select Conditional
Terminal from the shortcut menu. You must wire the conditional terminal and either wire
the count terminal or auto-index an input array for the loop to execute and for the VI to run.
To convert a For Loop to a While Loop, right-click the For Loop and select Replace with While
Loop from the shortcut menu.
Example: For Loop
The following example uses a For Loop in order to create an array with 10 elements and fill it
with random numbers.

Tutorial: An Introduction to LabVIEW

37

Loops and Structures

5.1.2

While L oop

A While loop repeats the sub diagram inside it until the conditional terminal, an input
terminal, receives a particular Boolean value. The Boolean value depends on the
continuation behavior of the While Loop. Right-click the conditional terminal and select Stop
if True or Continue if True from the shortcut menu. You also can wire an error cluster to the
conditional terminal, right-click the terminal, and select Stop on Error or Continue while
Error from the shortcut menu. The While Loop always executes at least once.
Below we see an empty While loop:

After you create a While Loop, you can use shift registers to pass values from one iteration
to the next. If you wire an array to a While Loop, you can read and process every element in
that array by enabling auto-indexing.
In order to convert a While Loop into a For Loop, right-click the While Loop and select
Replace with For Loop from the shortcut menu. To convert a While Loop into a Timed
Loop, right-click the While Loop and select Replace with Timed Loop from the shortcut
menu.
Example: While Loop
Tutorial: An Introduction to LabVIEW

38

Loops and Structures

This example run until either the user clicks the stop button or number of iterations is
greater than 10.

5.2 Structures
5.2.1

Case S tructure

The Case Structure has one or more sub diagrams, or cases, exactly one of which executes
when the structure executes. The value wired to the selector terminal determines which
case to execute and can be Boolean, string, integer, or enumerated type. You may right-click
the structure border to add or delete cases. Use the Labeling tool to enter value(s) in the
case selector label and configure the value(s) handled by each case.
Below we see an empty Case structure:

Tutorial: An Introduction to LabVIEW

39

Loops and Structures

Below we see an example of a Case structure with 2 cases, a True case and a False case.
Depending of the Boolean input value, the Numeric1 and Numeric2 is either Added or
Subtracted.

5.2.2

Sequence S tructure

A Sequence structure Consists of one or more sub diagrams, or frames, that execute
sequentially. Right-click the structure border to add and delete frames or to create sequence
locals to pass data between frames. Use the Stacked Sequence structure to ensure a sub
diagram executes before or after another sub diagram.
Below we see an empty Sequence structure.

Tutorial: An Introduction to LabVIEW

40

Loops and Structures

Below we see an example where we use Sequence Local, i.e., we pass a value from one

sequence to the next

Note! To take advantage of the inherent parallelism in LabVIEW, avoid overusing Sequence
structures. Sequence structures guarantee the order of execution, but prohibit parallel
operations. Another negative to using Sequence structures is that you cannot stop the
execution part way through the sequence.

5.2.3

Event S tructure

An Event structure has one or more sub diagrams, or event cases, exactly one of which
executes when the structure executes. The Event structure waits until an event happens,
then executes the appropriate case to handle that event. Right-click the structure border to
add new event cases and configure which events to handle. Wire a value to the Timeout
terminal at the top left of the Event structure to specify the number of milliseconds the
Tutorial: An Introduction to LabVIEW

41

Loops and Structures

Event structure should wait for an event to occur. The default is 1, indicating never to time
out.
Below we see an example:

Right-click on the border in order to Add/Edit Event Cases, see the dialog box below.

Tutorial: An Introduction to LabVIEW

42

Loops and Structures

Exercises
Exercise: For Loop
Create a VI with a For Loop. Create the logic to find out if a number in an array is greater
than 10. See Front Panel below:

Tutorial: An Introduction to LabVIEW

43

Loops and Structures

Exercise: While Loop
Create a VI with a While Loop. Create the logic to find out which (the first) index in the array
that have a number greater than 30. See Front Panel below:

Exercise: Case Structure
Create a VI with a Case Structure.
Use a Case structure inside a For Loop to write the text The Number is greater than 10 if
value is greater than 10. See Front Panel below:

Tutorial: An Introduction to LabVIEW

44

Loops and Structures

Exercise: Sequence Structure
Create a VI with a Sequence Structure. See Front Panel below:


Exercise: Event Structure
Create a VI with an Event Structure. See Front Panel below:

Tutorial: An Introduction to LabVIEW

6 Troubleshooting and
Debugging
This chapter explains the basic concepts of troubleshooting and debugging in LabVIEW.
Topics:

How to find errors

Highlight Execution
Probes
Breakpoints
Step into/over/out debugging

6.1 How t o f ind e rrors

If a VI does not run, it is a broken, or nonexecutable, VI. The Run button often
appears broken, shown at left, when you create or edit a VI. If it is still broken when you
finish wiring the block diagram, the VI is broken and will not run. Generally, this means that a
required input is not wired, or a wire is broken.
Click the broken Run button to display the Error list window, which lists all the errors.
Double-click an error description to display the relevant block diagram or front panel and
highlight the object that contains the error.

6.2 Highlight E xecution

View an animation of the execution of the block diagram by clicking the Highlight
Execution button. Execution highlighting shows the flow of data on the block diagram from
one node to another using bubbles that move along the wires. Note! Execution highlighting
greatly reduces the speed at which the VI runs.

45

46

Troubleshooting and Debugging

6.3 Probes
Use the Probe tool to check intermediate values on a wire as a VI runs.
When execution pauses at a node because of single-stepping or a breakpoint, you also can
probe the wire that just executed to see the value that flowed through that wire. You also
can create a custom probe to specify which indicator you use to view the probed data. For
example, if you are viewing numeric data, you can choose to see that data in a chart within
the probe. To create a custom probe, right-click a wire and select Custom Probe-New from
the shortcut menu.

Tutorial: An Introduction to LabVIEW

47

Troubleshooting and Debugging

6.4 Breakpoints

Use the Breakpoint tool to place a breakpoint on a VI, node, or wire on the block
diagram and pause execution at that location. When you set a breakpoint on a wire,
execution pauses after data pass through the wire. Place a breakpoint on the block diagram
workspace to pause execution after all nodes on the block diagram execute. When a VI
pauses at a breakpoint, LabVIEW brings the block diagram to the front and uses a marquee
to highlight the node or wire that contains the breakpoint. LabVIEW highlights breakpoints
with red borders for nodes and block diagrams and red bullets for wires. When you move
the cursor over an existing breakpoint, the black area of the Breakpoint tool cursor appears
white. Use the Breakpoint tool to click an existing breakpoint to remove it.
You may also right-click on the wire in order to set a breakpoint or open the Breakpoint
Manager.

Tutorial: An Introduction to LabVIEW

48

Troubleshooting and Debugging

Breakpoint Manager is a tool for enable, disable and delete breakpoints.

6.5 Step i nto/over/out d ebugging

Available Keyboard Shortcuts when Debugging:

Tutorial: An Introduction to LabVIEW

49

Troubleshooting and Debugging

Exercises
Exercise: Highlight Execution
Enable Highlight Execution in one of your programs, and see how it works.

Exercise: Probes
Set Several Probes around in your application and watch how it works. Use the Probe watch
Window and check out the functionality this tool offers.
Also check out the Custom Probe and the Find Probe functionality.

Exercise: Breakpoints
Set some Breakpoint around in your code and check out how it works. Use the Breakpoint
Manager tool.
Example:

Tutorial: An Introduction to LabVIEW

50

Troubleshooting and Debugging

Exercise: Step into/over/out debugging

Use the Step into/over/out functionality together with your Breakpoints and learn how you
can use them and see what the difference between them is.

Tutorial: An Introduction to LabVIEW

7 Working with Data

This chapter explains the basic concepts of creating and using Sub Vis in LabVIEW.
Topics:

Arrays
Array Functions
Cluster

7.1 Arrays
Arrays are very powerful to use in LabVIEW. In all your applications you would probably use
both One-Dimensional Arrays and Two-Dimensional Arrays.

7.1.1

Auto-Indexing

LabVIEW uses a powerful mechanism called Auto-indexing.

For Example you may use a For loop to create Array data like this:

Or you may use an Array like this in order to automatically specify number of iterations:

51

52

Working with Data

7.1.2

Array F unctions

LabVIEW has lots of built-in functions for manipulating arrays.

The most useful Array functions are:
Array Size
Index Array
Tutorial: An Introduction to LabVIEW

53

Working with Data

Delete from Array

Search 1D Array
Initialize Array
Build Array
Array Subset
Array Constant
All these functions are basic (but very useful) array functions you will probably be using in all
your applications and VIs.


Example: Array functions
In this example we see how we can use these Array functions and what they do.

Tutorial: An Introduction to LabVIEW

54

Working with Data

The resulting Front Panel is as follows:

7.2 Cluster
Clusters group data elements of mixed types, such as a bundle of wires, as in a telephone
cable, where each wire in the cable represents a different element of the cluster. A cluster is
similar to a record or a struct in text-based programming languages. Bundling several data
elements into clusters eliminates wire clutter on the block diagram and reduces the number
of connector pane terminals that subVIs need. The connector pane has, at most, 28
terminals. If a front panel contains more than 28 controls and indicators that you want to
use programmatically, group some of them into a cluster and assign the cluster to a terminal
on the connector pane. Like an array, a cluster is either a control or an indicator. A cluster
cannot contain a mixture of controls and indicators.

Tutorial: An Introduction to LabVIEW

55

Working with Data

Although cluster and array elements are both ordered, you must unbundle all cluster
elements at once rather than index one element at a time. You also can use the Unbundle
By Name function to access specific cluster elements.
Example of a Cluster in LabVIEW:

7.2.1

Cluster O rder

You may sort the different elements in the cluster by right-click on the cluster border and
select Reorder Controls in Cluster

Tutorial: An Introduction to LabVIEW

56

Working with Data

7.2.2

Cluster E lements

In order to manipulate and work with cluster LabVIEW offers lots of functions, such as the
Bundle and Unbundle functions.

In order to write to a cluster from the code, you may use the Bundle function or the
Bundle By Name function. See example below:
Tutorial: An Introduction to LabVIEW

57

Working with Data

Example: Clusters

In order to get access to the different elements in the cluster, you need to Unbundle by
using the Unbundle function or the Unbundle By Name. See example below:

Exercises
Exercise: Arrays
Create some simple VIs where you use these array functions to manipulate array data:
Array Size
Index Array
Delete from Array
Search 1D Array
Initialize Array
Build Array
Array Subset
Tutorial: An Introduction to LabVIEW

58

Working with Data

Exercise: Arrays
Create a SubVI that find the peaks in the input array regarding to an input peak level.

Exercise: Clusters
Create a Cluster and get the different values from the controls in the Cluster. See Front Panel
below:

Tutorial: An Introduction to LabVIEW

8 Working with Strings

Working and manipulating with strings is an important part in LabVIEW development.
On the Front panel we have the following String controls and indicators available from the
Control palette:

On the Block Diagram we have the following String functions available from the Functions
palette:

Some of the most important String functions are:
Concatenate Strings

59

60

Working with Strings

This function concatenates several strings into on string:

Search and Replace String

Use this when you want to replace or remove a certain text in a string.

Match Pattern

Tutorial: An Introduction to LabVIEW

61

Working with Strings

This is the most useful function when it comes to string manipulation.

Format Into String

Example:

Exercises
Here are some exercises using some of the String functions that are available in LabVIEW.
Exercise: SubVI: Remove leading zeros in string.vi
Tutorial: An Introduction to LabVIEW

62

Working with Strings

Create a SubVI which removes leading zeros in a string. Create a Test VI that uses the SubVI.

Exercise: SubVI: Remove space from end of string.vi
Create a SubVI which removes all spaces from the end of the string. Create a Test VI that
uses the SubVI.

Exercise: SubVI: Add 2 String.vi
Create a SubVI which adds 2 strings into one. Create a Test VI that uses the SubVI.

Tutorial: An Introduction to LabVIEW

9 Error Handling
This chapter explains the basic concepts of handle errors in your code.
Topics:

Finding Errors
Error Wiring
Error Handling

9.1 Finding E rror

If a VI does not run, it is a broken, or nonexecutable, VI. The Run button often appears
broken, shown at left, when you create or edit a VI. If it is still broken when you finish wiring
the block diagram, the VI is broken and will not run. Generally, this means that a required
input is not wired, or a wire is broken. Click the broken Run button to display the Error list
window, which lists all the errors. Double-click an error description to display the relevant
block diagram or front panel and highlight the object that contains the error.

9.2 Error W iring

Error handling is important in all programming languages. LabVIEW has powerful mechanism
for handling errors and error wiring.
You should always wire the Error cluster between all SubVIs, nodes, etc. that support this,
see example below.

The Error cluster is located in the Controls palette here:

63

64

Error Handling

The Error Cluster:

The Error cluster contains of the following parts:

Status True/False. False: No Error, True: Error

Code Error Code
Source Textual Error message

9.3 Error H andling i n S ubVIs

When creating SubVIs you should always create an Error In and an Error Out. In the SubVI
code you should also use a Case structure and wire the Error in cluster to the Case Selector
as shown below.

Tutorial: An Introduction to LabVIEW

65

Error Handling

9.4 Error H andling

LabVIEW has several useful SubVIs, etc for Error Handling:

Tutorial: An Introduction to LabVIEW

66

Error Handling

These are:

In general you should always show the error to the user. See LabVIEW Help for more details
of how to use these SubVIs.

Exercises
Exercise: Error Handling
Check out the different Error Vis in LabVIEW. Use them in some of your previous Vis.

Tutorial: An Introduction to LabVIEW

10 Working with Projects

This chapter explains the basic concepts of the project Explorer in LabVIEW.
Topics:

Project Explorer
Building .exe (executable) applications
Deployment: Create an Installer

10.1

Project E xplorer

It is not necessary to use the Project Explorer when developing your LabVIEW code, but it is
an easy way to structure your code, especially for larger projects.

The project Explorer is necessary when you want to deploy your code into, e.g., an
executable (.exe) application, build a setup, etc.

67

68

Working with Projects

The Project Explorer is also very useful when you integrate a source control tool, such as
Team Foundation Server, Visual Source Safe, etc. Then you may easily check files in and out
of the source code system.
In order to create a new Project in LabVIEW, simply select Empty Project from the Getting
Started window when you open LabVIEW.

10.2

Deployment

When your application is finished, you may want to distribute or deploy your application and
share it with others.
The Project Explorer gives you several choices when it comes to distribute and deploy your
application. Some of the options are:

Create an executable application (.exe) this means that the target doesnt need to
have LabVIEW installed on their computer. All the target need is LabVIEW Run-Rime,
which is a small installation package.
Tutorial: An Introduction to LabVIEW

69

Working with Projects

You may create your own installer, so all the target need is to run a setup.exe in
order to use your application
Other possibilities is to create a Web Service or a Shared Library (DLL) of your
application

All these options are available from the Project Explorer, just right-click on your Build
Specifications node.

We will go through how we create an executable application. Click Build
SpecificationsNewApplication (EXE).
In the Properties window fill in your name of the application.

Tutorial: An Introduction to LabVIEW

70

Working with Projects

Make sure you select a Startup VI.

There are lots of properties and setting you may use in order to create your application, go
through all the Categories in the Properties window.
When you have finished all the steps, just select Build in order to create your application.
When you make changes in your application, it is easy to rebuild your application:

Tutorial: An Introduction to LabVIEW

71

Working with Projects

Exercises
Exercise: Project Explorer
Create a new Project and put on of your existing application into the project
Exercise: Deployment
Create an executable application

Tutorial: An Introduction to LabVIEW

11 Design Techniques
This chapter explains some useful techniques to use when creating your application.
Topics:

Force the Program Flow using an Error cluster

Shift Register
State Machine
Multiple Loops
Templates

11.1

Force P rogram F low

As mentioned earlier, LabVIEW follows a dataflow model for running VIs. A block diagram
node executes when all its inputs are available. When a node completes execution, it
supplies data to its output terminals and passes the output data to the next node in the
dataflow path.
In the example below we cannot be sure that the DAQmx Write.vi executes before the
DAQmx Stop Task.vi executes. LabVIEW will in this case randomly execute one of these first.
If the Stop VI happens to execute first then the Write VI will failed because task has been
stopped.

In the example below we wire the Error cluster through all the VIs, and there will be no
doubt that the Write VI will execute before the Stop VI.

72

73

Design Techniques

This approach will also take care of the error handling in your program, which is very
important in real-world applications.

11.2

Shift R egister

Use shift registers on For Loops and While Loops to transfer values from one loop iteration
to the next. Shift registers are similar to static variables in text-based programming
languages. A shift register appears as a pair of terminals, directly opposite each other on the
vertical sides of the loop border. The right terminal contains an up arrow and stores data on
the completion of an iteration. LabVIEW transfers the data connected to the right side of the
register to the next iteration. Create a shift register by right-clicking the left or right border
of a loop and selecting Add Shift Register from the shortcut menu.
A shift register transfers any data type and automatically changes to the data type of the
first object wired to the shift register. The data you wire to the terminals of each shift
register must be the same type.
To initialize a shift register, wire any value from outside the loop to the left terminal. If you
do not initialize the shift register, the loop uses the value written to the shift register when
the loop last executed or the default value for the data type if the loop has never executed.
Use a loop with an uninitialized shift register to run a VI repeatedly so that each time the VI
runs, the initial output of the shift register is the last value from the previous execution. Use
an uninitialized shift register to preserve state information between subsequent executions
of a VI. After the loop executes, the last value stored in the shift register remains at the right
terminal. If you wire the right terminal outside the loop, the wire transfers the last value
stored in the shift register. You can add more than one shift register to a loop. If you have
multiple operations within a loop, use multiple shift registers to store the data values from
those different processes in the structure.

Tutorial: An Introduction to LabVIEW

74

Design Techniques

11.3

State P rogramming A rchitecture

Creating VIs using the State Machine approach is very useful when creating (large)
applications.
In general, a state machine is a model of behavior composed of a finite number of states,
transitions between those states, and actions. It is similar to a "flow graph" where we can
inspect the way in which the logic runs when certain conditions are met.

Sometimes, you may want to change the order of the sequence, repeat one item in the
sequence more often than the other items, stop a sequence immediately, or have items in
the sequence that may execute only when certain conditions are met. Although your
program may not have any such requirements, there is always the possibility that the
program must be modified in the future. Therefore, a state programming architecture is a
good choice, even if a sequential programming structure is sufficient. The following list

Tutorial: An Introduction to LabVIEW

75

Design Techniques

describes more complex programming requirements that justify the use of a state
programming architecture for an application.

You need to change the order of the sequence

You must repeat an item in the sequence more often than other items
You want some items in the sequence to execute only when certain conditions are
met

The State Machine approach in LabVIEW uses a Case structure inside a While loop to handle
the different states in the program, and the transitions between them. The Shift Register is
used to save data from and between the different states.
Below we see examples of a state machine principle implemented in LabVIEW.
Simple State Machine principle

Tutorial: An Introduction to LabVIEW

76

Design Techniques

State Machine with multiple transitions depending on the State:

More advanced State Machine using Shift Registers:

Tutorial: An Introduction to LabVIEW

77

Design Techniques

11.4 Multiple L oops/Parallel

programming
Often, you need to program multiple tasks so that they execute at the same time. In
LabVIEW tasks can run in parallel if they do not have a data dependency between them, and
if they are not using the same shared resource. An example of a shared resource is a file, or
an instrument.

Using multiple While loops is sometimes useful in applications that need to handle User
interactions in parallel with, e.g., DAQ operations, etc.
Below we see an example of how this structure could look like. The upper loop could handle
interaction with the user, while the lower loop could handle DAQ operations, such as
reading and writing to some I/O equipments.
Tutorial: An Introduction to LabVIEW

78

Design Techniques

In order to pass data between the loops, you may e.g. use local variables. The loop may have
different time cycles. The I/O may require faster cycles than the User interaction loop.

11.5

Templates

You should create your own templates for such VI you use a lot. It is easy to create your own
templates for scratch, just create a VI as you normally do and then save it as a template with
the ending .vit. You may also convert a VI you already made just by changing the extension
to .vit.
You should copy your templates to the LabVIEW template folder which is default located in
C:\Program Files\National Instruments\LabVIEW X.X\Templates\.

Tutorial: An Introduction to LabVIEW

79

Design Techniques

The Templates will then be available from the Getting Started Window or FileNew in
LabVIEW.
I may case I have created a sub folder called My Templates where I place all my templates.

Tutorial: An Introduction to LabVIEW

80

Design Techniques

Exercises
Here are some exercises about shift-registers, State Machines and parallel programming.
Exercise: Shift-register
Create a VI (see example below) where you have the following states:

Initialize
Write
Read
Close

In the VI you will use a shift-register as a temporary storage. In the Write state you Write
Data to the storage (shift-register) while you in the Read state will read the Data from the
Storage.
See Example below:

Tutorial: An Introduction to LabVIEW

81

Design Techniques

Write a Test program that test the SubVI, e.g.,

This example shows how you can use a shift-register as a temporary storage, which is very
useful in many situations.
Exercise: State Machine
Use the State Machine principle on one of your previous exercises.

Exercise: Parallel Programming
Create a VI that consists of 2 parallel loops. Use local variables and other mechanisms in
order to share data between the 2 loops.

Exercise: Templates
Tutorial: An Introduction to LabVIEW

82

Strip some of yours previous Vis and save them as reusable Templates.

Tutorial: An Introduction to LabVIEW

Design Techniques

12 User Interface
This chapter explains the basic concepts of creating user-friendly Graphical User Interfaces
(GUI) in LabVIEW.
Topics:

Decorations
Tab Control
Splitter
Sub Panel
Etc.

Below we see a Front Panel (GUI) with a poor design.

The information (Controls and Indicators) on the Front Panel is not structured. You should
group elements that naturally belong together and use different colors with care.
When creating Graphical User Interfaces (GUI) you should use the controls from the System
palette and not from the Modern or Classic palettes. Modern Controls may be used in Sub
Vis with no visible User Interface (for the user).
83

84

User Interface

The appearance of the controls in the System palette is standard MS Windows look and
feeling and this look is familiar for most users. These controls also change appearance due to
changes in the appearance in the operation system.

12.1

VI P roperties

In order to make the appearance of the Window that hosts your application, you should
always make some changes in the VI Properties.
You find the VI Properties by right-click on the icon in the upper right corner of your VI.

Tutorial: An Introduction to LabVIEW

85

User Interface

The first thing you should change is the Window title. Here you may type appropriate
name of your application or SubVI.
The next you should do is to the Customize button in order to customize the Window
appearance.

Below we see an application with a simple and neat User Interface and with a Customized
Windows appearance.

Tutorial: An Introduction to LabVIEW

86

User Interface

Below we see a professional application created in LabVIEW that implement common GUI
objects such as a Toolbar, a Tree view, a List view, etc..

Tutorial: An Introduction to LabVIEW

87

User Interface

Exercises
Exercise: User Interface
Create a Dialog Box where you use some of the Controls from the System palette. Make the
necessary settings in VI Properties in order to hide menus, buttons, create a Title, etc.
Create a Test VI from where you open this Dialog Box, enter some data in the Dialog Box,
and then retrieve these data in the calling VI.
Example:

Tutorial: An Introduction to LabVIEW

13 Plotting Data
This chapter explains the basic concepts when plotting data in LabVIEW.
LabVIEW offers powerful functionality for plotting data. In the Graph palette we have lots of
useful controls for plotting and visualization of data.

The most useful are:

Waveform Chart
Waveform Graph
XY Graph

Example:
This simple example creates a graph with some random values.

88

89

Plotting Data

The example below show the basic difference between a Chart and a Graph.

Tutorial: An Introduction to LabVIEW

90

Plotting Data

You use the Graph if you want to plot a set of data, e.g., an array with data, plot data from
a file, etc. Use the Chart if you want to plot one data point at a time, e.g., inside a loop,
etc.

13.1

Customizing

The different Chart components in LabVIEW offer a great deal of customizing.

You may click on the Plot Legend in order to set colors, different line
styles, etc.

Tutorial: An Introduction to LabVIEW

91

Plotting Data

If you right-click on the Graph/Chart, you may set properties such as auto-scaling, etc.

If you select Properties, you get the following dialog:

Tutorial: An Introduction to LabVIEW

92

Plotting Data

You may also select which items that should be visible or not.

The Graph Palette lets you zoom in and out on the Graph, etc.

Exercises
Exercise: Graph
Create a VI that reads data from a file and plot the data in a Graph component.

Exercise: Chart
Create a VI where you use Data Binding in order to retrieve data from an OPC demo.
Data Binding is set in the Properties Data Binding tab:

Tutorial: An Introduction to LabVIEW

93

Plotting Data

Exercise: Customizing
Customize the Graph and the Chart in the examples above in order to set colors, line
thickness, etc.

Tutorial: An Introduction to LabVIEW

14 Tips & Tricks

This chapter gives you some useful Tips & Tricks regarding LabVIEW.

14.1 10 f unctions y ou n eed t o k now

about
These are the 10 most useful functions in LabVIEW, so you could already now learn how to
use them and where to find them!

Build Array

This example using the Build Array function inside a For loop in order build an array with 10
elements.

Index Array

94

95

Tips & Tricks

It is always useful to find a specific value in an array:

The Index Array is extendible, so you can drag it out to find more than one elements:

Array Size

Find the size of an arbitrary array:

Tutorial: An Introduction to LabVIEW

96

Tips & Tricks

Select

Depending on the input data, go to the Alarm case or the Write Data case.

Concatenate Strings

This function concatenate several strings into on string:

Search and Replace String
Tutorial: An Introduction to LabVIEW

97

Tips & Tricks

Use this when you want to replace or remove a certain text in a string.

Match Pattern

This is the most useful function when it comes to string manipulation.

Format Into String

Tutorial: An Introduction to LabVIEW

98

Tips & Tricks

Example:

Fract/Exp String to Number

This function converts a string into a number:

Example: Number To Fractional String

Tutorial: An Introduction to LabVIEW

99

Tips & Tricks

Example:

14.2

The 1 0 m ost u seful S hort-cuts

These are the 10 most useful short-cuts in LabVIEW, so you could already now learn how to
use them!
Short-Cut
Ctrl + B
Ctrl + .
Ctrl + E
Tab
Ctrl + Mouse
wheel
Ctrl + H
Ctrl + Mouse
Double-click on a
SubVI
Ctrl + Arrows
( )
Ctrl + W
Double-click on a
wire

Description
Deletes all broken wires in a VI
Stops the Running VI
Toggle between the Front Panel and Block Diagram
Cycles through the most common Tools (Automatic Tool Selection
should be disabled!)
Scrolls through subdiagrams in Case, Event or Sequence structures
Displays the Context Help window
Opens the Block Diagram directly
Move faster. You first have to select a SubVI, a Function, Object, etc
Close the SubVI
Selects the hole wire

Tutorial: An Introduction to LabVIEW

15 Example Application
In this example we will go through an example application. The application uses most of the
LabVIEW features you have learned in this Tutorial.
The application is called Glossary. It is a simple application that learns kids words in
English. Since the application is for kids, the user interface is create with a childish look
and feel.

This is an example of how to create a user-friendly application in LabVIEW that uses most of
the functionality in LabVIEW, such as State-machine principles, reading and writing to files,
dialog boxes, graphics and sound effects. Basic functions for string and array manipulation,
and of course while loops, case structures, subVIs, etc. The example also uses the Project
Explorer to collect all the files in one place and to create an executable file of the solution.
Finally it uses the Project Explorer to create a setup package you can use to install the
application easily on other computers.

100

101

Example Application

I created this application for my kids in the Primary school who had problems with learning
their homework in English.
Use the code as an example for creating your own stunning LabVIEW applications. The code
is available for download at my blog: http://home.hit.no/~hansha.
Below we see the Glossary List:

If you click on the little book symbol in your application, this window will pop up:

Click tis symbol and you can enter new words:

Tutorial: An Introduction to LabVIEW

102

Example Application

The application uses the Project Explorer:

Tutorial: An Introduction to LabVIEW

103

Example Application

This makes it easy to keep an overview of all your files in your project. You may also use the
Project Explorer to create an executable file of your application. In addition you may also
create an installation package so you can easily install the application on other computers.
As part of the installation the LabVIEW Run-time engine will be installed.
Block Diagram:
The application uses the state machine principle, which makes it easy to create large
applications:

Tutorial: An Introduction to LabVIEW

104

Example Application

Tutorial: An Introduction to LabVIEW

16 Additional Exercises
This chapter lists lots of additional exercises you could try out in order to improve your
LabVIEW skills.
Exercise: vCard Reader
Create an application that reads information from a vCard.
vCard is a file format standard for electronic business cards. vCards are often attached to
e-mail messages, but can be exchanged in other ways, such as on the World Wide Web. They
can contain name and address information, phone numbers, URLs, logos, photographs, and
even audio clips.
Example:
BEGIN:VCARD
VERSION:2.1
N:Gump;Forrest
FN:Forrest Gump
ORG:Bubba Gump Shrimp Co.
TITLE:Shrimp Man
TEL;WORK;VOICE:(111) 555-1212
TEL;HOME;VOICE:(404) 555-1212
ADR;WORK:;;100 Waters Edge;Baytown;LA;30314;United States of America
LABEL;WORK;ENCODING=QUOTED-PRINTABLE:100 Waters Edge=0D=0ABaytown, LA 30314=0D=0AUSA
ADR;HOME:;;42 Plantation St.;Baytown;LA;30314;United States of America
LABEL;HOME;ENCODING=QUOTED-PRINTABLE:42 Plantation St.=0D=0ABaytown, LA 30314=0D=0AUSA
EMAIL;PREF;INTERNET:[email protected]
REV:20080424T195243Z
END:VCARD

For more information about the vCard format, see http://en.wikipedia.org/wiki/VCard.

The application should look something like this:

When the user click Open, then a dialog box like this should appear:

105

106

Additional Exercises

Requirements:

Use the Project Explorer

Use the State Machine principle
Use the Event Structure
Use System Controls
Set the appropriate settings in the VI Properties.
Create a executable application (vCard.exe)

Exercise: vCard Write & Read
Extend the application in the previous example. You should now be able to both write and
read vCard files. The application could look something like this:

Tutorial: An Introduction to LabVIEW

107

Additional Exercises

When the user clicks New, the dialog box in the previous exercise appears. The user may
enter a new vCard. If the user clicks Edit, a dialog box with the selected contact should
appear.

Exercise: Read/Write from .ini files
Read/Write from .ini files. Use the Configuration File VIs:

Exercise: ActiveX
Create a simple Web Browser using ActiveX and the Internet Explorer ActiveX control
(Microsoft Web Browser)
Use the ActiveX Container from the Containers control palette:

Tutorial: An Introduction to LabVIEW

108

Additional Exercises

Use the ActiveX function palette:

The application could look something like this:

Tutorial: An Introduction to LabVIEW

109

Additional Exercises

Exercise: Themes
In e.g., ASP.NET we have something called Themes. Themes are used to change the
appearance of your whole application regarding to color, font, pictures, etc.
LabVIEW do not offer such a functionality , but try to create your own Theme Configurator,
so you can change the appearance of your VI instantly.
Here is an example of how Windows XP handles different Themes:

Create a similar Theme Configurator so you may easily change the appearance of your Vis.

Tutorial: An Introduction to LabVIEW

17 Whats Next?
17.1

My B log

For more information about LabVIEW, visit my Blog: http://home.hit.no/~hansha/

17.2

Training

This Tutorial is a part of a series with other Tuturials I have made, such as:

Introduction to LabVIEW
Data Acquisition in LabVIEW
Control and Simulation in LabVIEW
LabVIEW MathScript
Linear Algebra in LabVIEW
Datalogging and Supervisory Control in LabVIEW
Wireless Data Acquisition in LabVIEW
Intermediate Topics in LabVIEW
Advanced Topics in LabVIEW
etc.

These Training Kits are available for download (.pdf files, source code, additional resources,
etc.) from my blog: http://home.hit.no/~hansha

17.3

Additional R esources

You find lots of information about LabVIEW in National Instruments web site:
www.ni.com

17.4

Examples

In the NI example Finder (HelpFind Examples) you find lots of useful examples that you
can play with or use as a start when creating your own applications.
110

111

Whats Next?

17.5

Documentation

As part of the LabVIEW installation there exist lots of useful documentation, such as Getting
Started manuals, User Manuals, etc.

Tutorial: An Introduction to LabVIEW

112

17.6

Whats Next?

LabVIEW W iki

LabVIEW Wiki is the free LabVIEW information resource that anyone can edit.
http://labviewwiki.org/Home

17.7

LabVIEW o n Y ouTube

There are lots of LabVIEW videos available at YouTube:

http://www.youtube.com/results?search_query=labview&search=Search

Tutorial: An Introduction to LabVIEW

Quick Reference

113

Quick Reference

Tutorial: An Introduction to LabVIEW







Telemark University College
Faculty of Technology
Kjlnes Ring 56
N-3918 Porsgrunn, Norway
www.hit.no


Hans-Petter Halvorsen, M.Sc.
Telemark University College
Department of Electrical Engineering, Information Technology and Cybernetics

E-mail: [email protected]
Blog: http://home.hit.no/~hansha/

Quick Reference

Tutorial: An Introduction to LabVIEW