Scribd
Upload
177 views3 pages

When To Us A Line or Load Reactor

LineLoad Reactor

Uploaded by

Jaggu Jrz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
177 views3 pages

When To Us A Line or Load Reactor

LineLoad Reactor

Uploaded by

Jaggu Jrz
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Application Note

When to Use a Line or Load Reactor


Protecting the Drive or the Motor

Input and output reactors serve very different purposes. Simply put, an input reactor protects the drive and an output reactor protects the motor. However, there are a few more details to determine the correct application.
Input (Line) Reactors
An input or line reactor helps protect a variable frequency drive (VFD) from input power line disturbances that could
cause nuisance tripping or damage to the drive. An input (line) reactor also reduces the harmonics that the VFD
generates back onto the line. Line reactors are sized based on the HP and voltage ratings of the drive in use. LenzeAC Tech uses 3% or 5% reactors. Input (line) reactors should be used in these circumstances:
. The input line power is prone to have disturbances such as surges, spikes, transients, etc.
2. The supply line power is very stiff (greater than 10 times the kVA rating of the connected VFD).
3. Where harmonic distortion is a concern. (IEEE-519 Harmonic Control in Electrical Power Systems)
Line reactors are connected in series between the input source and the VFD Controller. Refer to Figure 1 for proper
wiring installation. The reactor should be mounted as close to the drive as possible.
Input Line Reactor
Input Fuse

A1

A2

Input Fuse

B1

B2

Input Fuse

C1

C2

Controller

Motor

Figure 1: Input (Line) Reactor


3% Impedance Line Reactors
3% impedance line reactors should be used to reduce power line transient voltages caused by capacitor switching,
line notching, DC Bus over-voltage tripping and inverter over-current and over-voltage conditions. They improve
the true input power factor and reduce cross-talk between drives.
The input (line) reactor offers some protection to the drive in short-circuit conditions. If the supply transformer kVA
rating is greater than ten times the drive kVA rating, then a line reactor is recommended to minimize damage to the
drive in case the supply transformer ever shorts out. This line impedance is dependent on the short-circuit rating for
the drive and on the supply power distribution transformer. Specifically, the line impedance must be greater than
or equal to the ratio of the supply source transformers rating to the drives short circuit rating.
For example, lets say you have a 100kVA, 460V, 120A power transformer for your source and install a 3% line
reactor in front of an MC series drive*. This means for the simplest calculation, the available short-circuit current
would be 120A/.03 = 4000Amps. This is less than the MC series 5000A rating so the 3% line reactor would work
fine. You can make this same calculation by determining the current of the supply transformer and the line reactor
impedance.
* The source transformer's impedance is not included because the difference in size makes it negligible.

Copyright 2008 by AC Technology

AN 0032/A1
www.lenze-actech.com
For general information only. Content subject to change without notice.

July 2008
1-508-278-9100

Application Note
5% Impedance Line Reactors
5% impedance line reactors have the same benefits as the 3% reactors plus they provide maximum harmonic mitigation without added capacitance. These harmonic signals produce distortion levels that may not be acceptable for
certain high frequency or noise sensitive equipment. Use of them will help to comply with the IEEE 519 Standard
and reduce motor operating temperature and motor noise.
Multiple Input (Line) Reactors
In applications involving multiple drives in parallel, having more than one VFD connected to a common power line
requires one line reactor per drive. Individual reactors will provide proper filtering and optimum surge protection for
each VFD and reduce crosstalk between each unit. A single reactor connected to multiple VFDs does not provide
adequate protection, filtering or reduce harmonic distortion when the system is partially loaded.
Each line reactor is connected in series between the input source and the VFD Controller. Refer to Figure 2 for
proper wiring installation. Each set of input lines to the drive should be in its own separate steel conduit. The reactor
should be mounted as close to the drive as possible.
Input Line Reactors
Input Fuse

A1

A2

Input Fuse

B1

B2

Input Fuse

C1

C2

Input Fuse

A1

A2

Input Fuse

B1

B2

Input Fuse

C1

C2

Controller

Motor

Controller

Motor

Figure 2: Multiple Input (Line) Reactors


Output (Load) Reactors
An output (load) reactor, on the other hand, is used to protect the motor if the wiring distance between the VFD and
motor is very long. The drive generates a high frequency PWM three-phase output and noise spikes are generated
on the leading edge of these signals. These noise spikes get amplified due to the long cable lengths and the additional capacitance of the cable. The resulting voltage can exceed the motors peak voltage rating where insulation
breakdown occurs.
The general rule of thumb is that an output reactor should be used if the motor wiring is over 100 feet, but this value
varies depending on the motor. If the motor meets the NEMA MG-1 Part 31 standard, it is possible to have as much
as 300 ft of cabling without a reactor. If it does not meet the standard, the maximum cable length should be 100
ft. Also, if the distance is between 300 and 500 ft, a load reactor must be installed.


Copyright 2008 by AC Technology

AN 0032/A1
www.lenze-actech.com
For general information only. Content subject to change without notice.

July 2008
1-508-278-9100

Application Note
If the distance is between 500 and 1000 ft, you would use a special type of filter called a dV/dT filter, as they
provide better protection at these extreme distances. This also varies depending on output cable specs, shielding,
power conditions, and noise suppression as well as isolation techniques.
Load reactors are connected in series between the VFD Controller and the motor. Refer to Figure 3 for proper wiring
installation. The reactor should be mounted as close to the drive as possible.
Output Load Reactor
Input Fuse
Input Fuse

Controller

Input Fuse

A1

A2

B1

B2

C1

C2

Motor

Figure 3: Output Load Reactor


Multiple Motors
For an application involving more than one motor being controlled by a single drive, a single reactor can typically
be used between the VFD and the motors. Note that each motor requires a separate thermal overload for proper
protection. The reactor should be sized based on the total motor/load horsepower.
The load reactor is connected in series between the VFD Controller and the motors. Refer to Figure 4 for proper
wiring installation. Each set of motor cables should be in a separate steel conduit to avoid noise and crosstalk that
can cause nuisance tripping. The reactor should be mounted as close to the drive as possible.
Output Load Reactor
Input Fuse
Input Fuse
Input Fuse

Controller

A1

A2

B1

B2

C1

C2

Motor

Motor

Figure 4: Output (Load) Reactor & Multiple Motors


Copyright 2008 by AC Technology

AN 0032/A1
www.lenze-actech.com
For general information only. Content subject to change without notice.

July 2008
1-508-278-9100

You might also like