Active Tuning Antenna System ATAS-25 Installation/Operating Instructions

Download as pdf or txt
Download as pdf or txt
You are on page 1of 1

Active Tuning Antenna System

ATAS-25
Installation/Operating Instructions
Thank you for choosing Yaesus exciting new ATAS-25 Active Tuning Antenna System. We hope and trust that you will enjoy many
years of enjoyable field operation with the ATAS-25!
The ATAS-25 utilizes a manual tuning system which resonates the radiating element for lowest SWR without the need for expensive, inconvenient mono-band resonating whip assemblies. The ATAS-25 allows dual-frequency operation (on HF or 50 MHz and
either 144 or 430 MHz), if two transceivers are combined via a suitable diplexer (not supplied). The ATAS-25 is designed to mount
directly onto a standard camera tripod (not supplied); see Figure 1.

INSTALLATION
1. Mount the ATAS-25 main body onto the tripod.
2. Referring to Figure 2 and the following chart, connect the
radiating elements according to the operating band, then
screw the radiating element securely to the top of the coil
assembly of the ATAS-25.
OPERATING BAND
7 MHz
14 MHz
21 MHz
28 MHz
50 MHz
144 MHz
430 MHz

have to be moved manually to the appropriate antenna jack when


you wish to operate on VHF or UHF.
While operation is not guaranteed on the 10/18/24 MHz bands,
please feel free to experiment on these bands, as low SWR and
good efficiency will be obtained in many instances.

RADIATING ELEMENT(S)
Three Elements
Three or Two Elements
Two Elements
Two or One Element(s), or No Connection
Do Not Connect
Not Used
Not Used

NOTE: When the ATAS-25 is fitted with two radiating


elements, use the top radiating element (the one with
the rubber cap) and the bottom radiating element (the
one with the threaded adapter at the bottom). When the
ATAS-25 is fitted with only one radiating element, move
the threaded adapter to the bottom of the element with
the rubber cap, then screw that element onto the top of
the coil assembly (Figure 3).
3. Secure the V/UHF radial elements to the bottom of the ATAS25 main body, using the supplied Allen wrench (Figure 4).
4. Connect the supplied radial wires to the bottom of the ATAS25 main body, then extend them outward from the antenna
base (Figure 5).
5. Connect the coaxial cable from the transceivers HF antenna jack (see Figure 6). Typically, you can use the builtin SWR meter in the transceiver, but alternatively you may
adjust the SWR using an Antenna Analyzer prior to connecting the coaxial cable to your transceiver.

E A C 8 2 X 7 0 0

CAUTIONS

For the 144/430 MHz bands, you may operate instantly without making any adjustments. For HF/50 MHz operation, perform the following procedures for antenna adjustment:

 The ATAS-25 is designed for temporary field operation.


We do not recommend that the ATAS-25 be used for permanent operation, as it does not include the weatherproofing needed for long-term outdoor installation.
 The ATAS-25 is designed for a maximum power of 100
Watts (SSB/CW) or 50 Watts (AM/FM, 144 MHz, 430 MHz).
Do not exceed this combined power input (if two transmitters are connected via a diplexer) when operating the ATAS25.
 Do not connect (mount) the ATAS-25 to the antenna jack
of the transceiver or antenna mount directly using a doublemale coaxial adapter plug. The ATAS-25 must be mounted
onto a tripod or other similar item using the Camera Screw
hole (Type U) on the bottom of the ATAS-25 main body.
 Do not allow anyone to touch the radiating element during
a transmitting session, due to the danger of burning of the
skin caused by the high RF voltage present. It helps the
accuracy of the SWR measurements if all people are standing at least 10 feet (3 m) away from the radiating element,
anyway, to minimize inaccuracies due to mutual coupling
to the human figure(s) in the vicinity.
 If erratic transceiver operation is observed, there may be
common-mode current flowing on the shield of the coaxial
cable. Make an RF choke by coiling about eight turns of
cable into a coil of diameter approximately 6 (roughly 150
mm) near the ATAS-25, taping the coils to hold them in
place. If this does not eliminate the problem, reverse the
coax ends, placing the coil near the transceiver. If additional cable is available, place a coil at both ends of the
coaxial cable in difficult cases.
 Set up the tripod as low and level as possible, for maximum stability of the tripod/antenna assembly. SWR tends
to be best with the base of the ATAS-25 near the ground,
as well (Figure 1).
 Should the ATAS-25 get wet due to rain, wipe off the
antennas components using a dry cloth, then completely
dry the ATAS-25 overnight with the coil assembly fully extended.
 For SSB/CW DX operation on the 144/430 MHz bands,
remember that the convention for polarization in most areas is horizontal, not vertical, so we recommend the ATAS25 mostly for local FM work on those bands.
 Make every effort to install the ATAS-25 away from areas
where people might trip over the tripod legs, coaxial cable,
or counterpoise wires. We strongly recommend that the
tripod legs be staked firmly to the ground, or the tripod and
antenna be otherwise secured with guy ropes and stakes,
to prevent the antenna from accidentally tipping over, so
as to avoid injury to bystanders and/or damage to antenna
components.

1. Tune the transceiver to the desired operating frequency.


2. Referring to Figure 7, raise and lower the coil assembly
while listening to the band noise, and seek the position of
the coil assembly producing the most noise in the receiver.
If a peak in the sensitivity is not obtained when the coil
assembly is fully retracted to the lowest (shortest) position, remove one radiating element from the coil assembly
and try again. You may have a total antenna length that is
too long.
3. Key the transmitter in the CW mode, and check the SWR
meter reading.
4. Referring to Figure 7 again, carefully turn the coil assembly to the right or to the left while the transceiver is receiving. After making an adjustment, stand away from the antenna and check the SWR again, and repeat (or reverse)
the procedure until the best SWR is obtained. Do not touch
the coil assembly during a transmitting session.
5. If low SWR on an HF band cannot be satisfactorily obtained, connect (add) the supplied spare radial wire to the
bottom of the ATAS-25 main body and extend it outward
from the antenna base, then try the above procedures
again.

Fine Tuning

Figure 1

Coarse Tuning

Figure 7

SPECIFICATIONS

If you operate the ATAS-25 along with the FT-817, we recommend that you set the transceivers Menu #07 (ANTENNA) to
REAR for all bands (HF/50/144/430 MHz), to pass all bands RF
power to the rear antenna jack of the FT-817. Refer to the FT-817
operating manual for details regarding the Menu selections.
For operation on the 144 and 430 MHz bands, in addition to HF/
50 MHz using the FT-847/-100/-100D/-857/-897, you may wish
to consider the purchase of a Diplexer (for the FT-100/-100D/
-857/-897) or Triplexer (for the FT-847) device to contact to the
appropriate transceivers antenna jack; the Diplexer or Triplexer
will then automatically pass RF power from the band in use while
isolating the other one or two jacks. If you do not have a Diplexer
or Triplexer, the coaxial cable connector from the ATAS-25 will

OPERATION

Figure 2

Figure 3

Figure 4

Frequency Range: 7/14/21/28/50/144/430 MHz


Amateur Bands
Input Impedance: 50 Ohms
Max. Input Power: HF/50 MHz: 100 W (SSB/CW, 50% Duty)
50 W (AM/FM)
144/430 MHz: 50 W (ALL MODE)
Matched SWR:
Less than 2.0:1
Height (Approx.): Max. 7.2 ft (2.2 m) during Operation
Min. 1.96 ft (0.6 m) for Transporting
Weight (Approx.): 2.05 lb. (930 g)

SUPPLIED ITEMS

Figure 5

Figure 6

ATAS-25 Main Body .............................................................. 1


Radiating Elements .............................................................. 3
Radial Element (for VHF band) ............................................ 1
Radial Element (for UHF band) ............................................ 1
Radial Wires (20 ft (6 m) , 9.8 ft (3 m) & 6.6 ft (2 m) Length) ... 1
Spare Radial Wire (32.8 ft (10 m) Length) ........................... 1
Allen Wrench ........................................................................ 1
Operating Manual ................................................................. 1

VERTEX STANDARD CO., LTD.


4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan

VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.

YAESU EUROPE B.V.


P.O. Box 75525, 1118 ZN Schiphol, The Netherlands

YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.

VERTEX STANDARD HK LTD.


Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong

You might also like