CONTROL & RELAY

PANEL

March 2015

Engineering Department
WEST BENGAL STATE ELECTRICITY TRANSMISSION COMPANY LIMITED

Regd. Office: VidyutBhawan, Block DJ, Sector-II, Bidhannagar, Kolkata 700091.

CIN: U40101WB2007SGC113474; Website: www.wbsetcl.in

WBSETCL / TECH SPEC / Rev.-1

Page 1 of 104

Control & Relay Panel

TECHNICAL SPECIFICATION FOR CONTROL & RELAY PANEL

1.00

SCOPE:

1.01

The specification covers design, engineering, manufacture, testing & supply delivery at site
of Control and relay Board and protection relay panels inclusive of internal wiring and
with arrangement for external connection to various Switchyard equipments and Control
room building equipments as necessary. The Contractor has to design the Schematics for
protection and Control of all equipments including monitoring indications, visual and audible
alarm, interlocking schemes between different equipment.
Any other requirement which
are not specifically covered here but which are necessary for successful commissioning
of the Sub-station are also within the scope of the Contract. The same shall be indicated
by the bidder with their price for WBSETCL's consideration.

1.02

The equipment manufactured should conform to the relevant standards and of highest quality
of engineering design and workmanship. The equipment manufactured
shall
ensure
satisfactory and reliable performance throughout the service life.

2.00

STANDARDS:

2.01

Unless otherwise specified all equipment and material shall conform to the latest IS applicable
standards. Equipment complying with other internationally recognised standards will also be
considered if it ensures performance equivalent or superior to Indian standards. In the event
of supply of equipment conforming to any international\ internationally recognised standards
other than the standard listed below, the salient features of comparison shall be brought
out and furnished along with the bid. One copy of such standard specification in English
language shall be enclosed with the tender.

2.02

The equipment provided shall also comply with the latest revisions of Indian Electricity act
and Indian Electricity rules and any other applicable Statutory provisions, rules and
regulations.

2.03

All equipment provided under the specification shall generally conform to the latest issue of
the following:
IEC/Indian Standard No.

Title

IS 3231 & IEC-255

Electrical relays for power system protection

IS 1248 & IS 2419

Indicating Instrument

WBSETCL / TECH SPEC / Rev.-1

Page 2 of 104

Control & Relay Panel

3.00

IS 6236

Recorders

IS 722

Static Energy meters

IEC 679

Static TVM

IEC 337 &337-1

Control Switches (LV Switching devices for control and auxiliary

circuit)

IS 2705

Current Transformers

IS 3156

Voltage Transformer

IS 4237

General requirement for Switch gear and Control gear for voltage
not exceeding 1 KV.

IS 375

Marking and arrangement for Switchgear Bus bars, main

connection and auxiliary wiring.

IS 8686

Specification for static protective relays

REQUIRED QUANTITIES:
Quantity of C & R panels are to be assessed by the bidders from the Schedule enclosed
with this specification. However, if any corridor in the switchyard layout is left for future use
in between two proposed bays included in the project, blank panels without any equipment,
relays etc but only with matching mimic are to be supplied.

4.00

Technical particulars to be considered for Design of Control and relay board, and
protection panels:

4.01

SYSTEM DETAILS :
a) Nominal System
Voltage
b) Highest System
Voltage
c) Number of Phases

400KV
------400KV

220KV
----220KV

132KV
----132KV

33KV
----33KV

420KV

245KV

145KV

36KV

<-------------------------- Three ------------------------->

d) Frequency

<-----------------------50 Hz +/- 3% ------------------->

e) Grounding

< -------- Effectively Earthed------------->

f) Maxm. fault
Current

50KA
(rms)

WBSETCL / TECH SPEC / Rev.-1

Page 3 of 104

40KA
(rms)

31.5KA
(rms)

through E.Tr.

Control & Relay Panel

4.02

AUXILIARY SUPPLY :
D.C.Supply voltage shall be normally fed from Battery charger and battery connected in
parallel which is 220V +/- 10%. In case of failure of the AC supply to battery charger, DC
Supply voltage will be available automatically from lead acid Battery. The D.C Supply voltage
may vary from -10% to + 10%. The D.C. system shall be 2 wire with necessary positive earth
fault and negative earth fault annunciation scheme. The ripple content in the D.C. supply
from charger will be less than 2%.
AC Auxiliary supply voltage for the C&R panel shall be 230V, 1-phase, 50Hz grounded with
+/- 10% voltage variation.

WBSETCL / TECH SPEC / Rev.-1

Page 4 of 104

Control & Relay Panel

5.00

CT & PT RATIO AND INDICATING INSTRUMENT RANGE:

5.01

CORE DETAILS OF CURRENT TRANSFORMER

Sl.
No.

Description

1. a)

400 KV CT (Bay Two main one Transfer Scheme)

20001
Protection
1000/1A
20002
Protection
Feeder,
1000/1A
Transformer, Bus
2000Reactor, Bus
5
3
Metering
1000/1A
Coupler & Bus
2000Transfer Bay
4
Protection
1000/1A
20005
Protection
1000/1A
400kV CT (One & a Half Breaker Scheme)
4
3000Protection
cores
2000/1A
Line side CT
6
2
3000-2000Metering
cores
1000/1A
4
3000Tie & Bus side CT
4
Protection
cores
2000/1A

b)
i

ii
c)

No
of
Core

Core
No.

Application

Current
Ratio

Output
Burden
(VA) at
Lower
Ratio

20

20

ISF
(Max)

Accuracy
class as
per IS
2705

Min Knee
point
Voltage (V)

Max CT Secy
Winding
Resistance
(W)

PS Class

2000/1000

10/5

30/60

PS Class

2000/1000

10/5

30/60

PS Class

2000/1000

10/5

30/60

PS Class

2000/1000

10/5

30/60

PS Class

3000/2000

15/10

30/45

PS Class

3000/2000

15/10

30/45

PS Class

1000V

2.5

30 at Vk/2

Max
excitation
current (mA)
at Knee point
Voltage

0.2

0.2

Bushing CT (Transformer)
400KV side,
220kV side &
Neutral of 315
MVA,
400/220/33KV
Transformer

WBSETCL / TECH SPEC / Rev.-1

Protection

1000/1A

Page 5 of 104

Control & Relay Panel

Sl.
No.

d)

ii

2. a)

ii

Description

No
of
Core

Core
No.

Application

Current
Ratio

Output
Burden
(VA) at
Lower
Ratio

ISF
(Max)

Accuracy
class as
per IS
2705

Min Knee
point
Voltage (V)

Max CT Secy
Winding
Resistance
(W)

Max
excitation
current (mA)
at Knee point
Voltage

Bushing CT (Bus Reactor)

400KV line side
of 80MVAR Bus
Reactor

Neutral side of
80MVAR Bus
Reactor

Protection

200/1A

PS Class

200V

40 at Vk/4

Protection

200/1A

PS Class

200V

40 at Vk/4

Protection

200/1A

PS Class

200V

40 at Vk/4

Metering

Protection

PS Class

2000/1000V

10/5

30/60

Protection

PS Class

2000/1000V

10/5

30/60

Protection

200/1A
20001000/1A
20001000/1A
200/1A

PS Class

200V

40 at Vk/4

WTI

Metering

Protection

5/4/2

30/37.5/75

Protection

Protection

Protection

Metering

Protection

Protection

10

10

220 KV CT (Bay)

Feeder,
Transformer &
Bus Transfer Bay

Bus Coupler

WBSETCL / TECH SPEC / Rev.-1

1000-800400/1A
1000-800400/1A
1000-800400/1A
1000-800400/1A
1000-800400/1A
20001600/1A
20001600/1A
20001600/1A

20

0.2
PS Class
PS Class
PS Class
PS Class

20

Page 6 of 104

1500/1200/
600V
1500/1200/
600V
1500/1200/
600V
1500/1200/
600V

5/4/2
5/4/2
5/4/2

30/37.5/75
30/37.5/75
30/37.5/75

0.2
PS Class

2000/1600V

10/8

30/37.5

PS Class

2000/1600V

10/8

30/37.5
Control & Relay Panel

Sl.
No.

b)

ii
c)

3. a)

Description

No
of
Core

Core
No.

Application

Current
Ratio

Output
Burden
(VA) at
Lower
Ratio

ISF
(Max)

Accuracy
class as
per IS
2705

Min Knee
point
Voltage (V)

Max CT Secy
Winding
Resistance
(W)

Max
excitation
current (mA)
at Knee point
Voltage

Bushing CT (Transformer)
220KV side,
132KV side &
Neutral of
160MVA
Transformer
220KV side &
Neutral of 50MVA
Transformer

Protection

800/1A

PS Class

1000V

2.5

30 at Vk/2

Protection

400/1A

PS Class

800V

1.5

30 at Vk/2

Metering

200-100/1A

Protection

200-100/1A

PS Class

1200/600V

4/2

30

Protection

200-100/1A

PS Class

1200/600V

4/2

30

Metering

Protection

1000-800400/1A
1000-800400/1A

1500/1200/
600V

5/4/2

30/37.5/75

Protection

5/4/2

30/37.5/75

Protection

1000-800400/1A

PS Class

1500/1200/
600V

5/4/2

30/37.5/75

Protection

1000-800400/1A

PS Class

1500/1200/
600V

5/4/2

30/37.5/75

33 KV CT for Tertiary Loading

220/132/33 KV
Transformer Bay

20

0.2

132KV CT (Bay)

Feeder,
Transformer &
Bus Transfer Bay

WBSETCL / TECH SPEC / Rev.-1

20

0.2
PS Class
PS Class

1000-800400/1A

Page 7 of 104

1500/1200/
600V

Control & Relay Panel

Sl.
No.

Description

No
of
Core

Core
No.

Application

Metering

20001600/1A

Protection

20001600/1A

PS Class

2000/1600V

Protection

20001600/1A

PS Class

2000/1600V

Protection

400-300/1A

PS Class

ii
Bus Coupler Bay

b)
i

Bushing CT (Transformer)
132KV side &
1
1
Neutral of 50MVA
Transformer

Current
Ratio

Output
Burden
(VA) at
Lower
Ratio

ISF
(Max)

Accuracy
class as
per IS
2705

20

0.2

Min Knee
point
Voltage (V)

Max CT Secy
Winding
Resistance
(W)

Max
excitation
current (mA)
at Knee point
Voltage

8/6.4

30/37.5

8/6.4

30/37.5

800-600V

1.5

30 at Vk/2

ii

33KV side of
50MVA
Transformer

Protection

1000/1A

PS Class

500

2.5

30 at Vk/2

iii

132KV side &

Neutral of
31.5MVA
Transformer
33KV side of
31.5MVA
Transformer

Protection

150/1A

PS Class

600

1.5

30 at Vk/2

Protection

800/1A

PS Class

400

2.5

30 at Vk/2

Metering

Protection

30/37.5/75

Protection

1000/800/40
0
1000/800/40
0

4/3.2/1.6

1000-800400/1A
1000-800400/1A
1000-800400/1A

4/3.2/1.6

30/37.5/75

iv

4. a)

33KV CT (Bay)

i
Feeder,
Transformer,
Capacitor Bank &
Bus Transfer Bay
WBSETCL / TECH SPEC / Rev.-1

20

0.2
PS Class
PS Class

Page 8 of 104

Control & Relay Panel

Sl.
No.

b)
i

Description

No
of
Core

33KV CT (Indoor Switchgear)

1
Feeder,
Transformer,
2
3
Capacitor Bank &
Bus Transfer Bay
3

ii
Bus Coupler Bay

5.02

Core
No.

Application

Metering
Protection
Protection

Metering

Protection
(O/C & E/F)

Current
Ratio

1000-800400/1A
1000-800400/1A
1000-800400/1A
1000-800/1A

Output
Burden
(VA) at
Lower
Ratio

ISF
(Max)

Accuracy
class as
per IS
2705

20

0.2

30

1000-800/1A

Min Knee
point
Voltage (V)

Max CT Secy
Winding
Resistance
(W)

PS Class

250/200/100

4/3.2/1.6

30/37.5/75

PS Class

1000/800/40
0

4/3.2/1.6

30/37.5/75

250/200

4/3.2

30 at Vk

Max
excitation
current (mA)
at Knee point
Voltage

0.2
PS

CORE DETAILS OF VT

Sl. No.

Description of Core

Number of
Core

Core Details of Core I

CVT/PT

Core Details of Core II & III

CVT/PT

400000/ 3 : 110 / 3, 110/ 3, 110/ 3

100 VA, 0.2

100 VA , 3P

2 a)

AIS:- 220000/ 3 : 110 / 3, 110/ 3, 110/ 3

50/200 VA, 0.2

50/200 VA , 3P

b)
3 a)
b)

GIS:- 220000/ 3 : 110 / 3, 110/ 3, 110/ 3

AIS:- 132000/ 3 : 110 / 3, 110/3, 110/ 3
GIS:- 132000/ 3 : 110 / 3, 110/3

3
3
2

50/100 VA, 0.2

50/200 VA, 0.2
50/100 VA, 0.2

50/100 VA, 3P
50/200 VA , 3P
50/100 VA, 3P

4 a)

AIS:- 33000/ 3 : 110 / 3, 110/ 3

100 VA, 0.2

100 VA, 3P

b)

Indoor Switchgear: 33000/ 3 : 110 / 3, 110/ 3

50 VA, 0.2

50 VA, 3P

WBSETCL / TECH SPEC / Rev.-1

Page 9 of 104

Control & Relay Panel

5.03

INDICATING INSTRUMENT RANGE

Indicating instruments (Ammeter, Voltmeter, MW meter, MVAR meter) shall be set as per the
CT ratio mentioned in the following table:
Ammeter Range: 400kV AIS
400kV (GIS)
220kV (AIS & GIS)
Feeder
2000A
Line side
3000A
Feeder
800A
315MVA
1000A
160MVA Transformer,
800A
Transformer,
220kV side
400kV side
Reactor
200A
50MVA Transformer,
300A
220kV side
Bus Transfer
2000A
--Bus Transfer (for AIS
800A
only)
Bus Coupler
2000A
Bus Coupler
1600A
132kV AIS
Feeder
600A
160MVA
800A
Transformer,
132kV side
50MVA
300A
Transformer,
132kV side
Bus Transfer
800A

132kV GIS
Feeder
800A
160MVA
800A
Transformer,
132kV side
50MVA
300A
Transformer,
132kV side
Bus Coupler
1600A

33kV AIS & Indoor Switchgear

Feeder
400A
50MVA Transformer,
1000A
33kV side
Bus Transfer (for AIS
only)

1000A

Voltmeter Range: 400kV

220kV
132kV
33kV

0-500kV
0-250kV
0-150kV
0 40kV

Wattmeter & VARmeter Range: -

400kV
Feeder
Bus Tr
Bus Coupler
315MVA Trafo
Reactor
220kV
Feeder
160MVA Trafo
315MVA Trafo
Bus Trf
Bus Coupler
One & Half Breaker System
Feeder
160MVA Trafo

MW

MVAR

0 to 1400

0 to 1400

0 to 800
---

0 to 800
0 to 100

0 to 300

0 to 300

0 to 400

0 to 400

0 to 600

0 to 600

0 to 600

0 to 600

132kV
WBSETCL / TECH SPEC / Rev.-1

Page 10 of 104

Control & Relay Panel

Feeder
160MVA Trafo
Bus Trf
Bus Coupler
50MVA Trafo
33kV
Feeder

0 to 100

0 to 100

0 to 200
0 to 70

0 to 200
0 to 70

0 to 25

0 to 25

6.00

PANEL DESCRIPTION, CONSTRUCTION AND FORMATION:

6.01

GENERAL REQUIREMENT:

a)

The control and relay board panels for 400KV system shall be duplex/simplex type (as
applicable as per Bus configuration) so as to accommodate all the control equipment,
breaker relays, meters etc. excepting the protective relays and its aux. relays/accessories as
necessary for completeness of the protection/control scheme without overcrowding and
cramping. Separate protection panels of simplex type (minimum 2 nos) shall be provided for
accommodating the protective relays and its aux. relays/accessories as required to fulfill the
scheme requirement.

b)

The control and relay board panel for 220KV system and 132KV system shall also be duplex
type for accommodating all relays and aux. relays for protection of respective circuit along
with control equipment, meters etc. as necessary for
completeness
of
the
protection/control scheme without overcrowding and cramping. However, the 33KV C&R
board panels shall be simplex type for accommodating all the control, protection and
metering equipment properly.

c)

Size of individual panel shall be as stated below :

Type
Duplex

Depth (mm)
1982

Width (mm)
as necessary but limited
to 1000 mm

Height (mm)
2312 including channel base.

Simplex

610

-do-

2250 including channel base

There shall be a corridor of 762 mm wide and access doors of 1900 mm height with latch at
two ends of duplex panel board for inspection. The door with door frame shall be detachable
type so that the same can be fitted to newly erected panel of similar design if any new C&R
panel is added. The access door for the simplex type panel shall be at the back side and of
1900 mm height.
d)

The front and rear parts of duplex type C&R panel shall be detachable and all inter
connection between front and rear panels shall be through terminal connector and preferably
underneath the top cover. The interconnection between the simplex type control and relay
panel and duplex type respective C&R panels where applicable will be made through cables to
be laid in the cable trenches under those panels.

e)

The complete panel shall incorporate all necessary instruments, meters, relays, auxiliary
relays, control switches, indicating lamps, mimic, annunciators, audible alarms, horizontal
and vertical wiring trough, wiring supports, interior lighting system, terminal blocks fuses
and links etc.

WBSETCL / TECH SPEC / Rev.-1

Page 11 of 104

Control & Relay Panel

6.02

CONSTRUCTIONAL FEATURES:

a)

The control & relay board shall comprise of cubicle type panels placed in juxta position to
form a continuous board for each system voltage. If the panels are required to be aligned in
right angular formation, the tenderer shall be required to arrange dummy/covering plates for
the uniform formulation without any extra price.

b)

The tenderer shall ensure

complementary equipment
properly accommodated in
panels with larger width. No

c)

Panels shall be completely metal enclosed and shall be dust, moisture and vermin proof.
The enclosure shall provide a degree of protection not less that IP-31 in accordance with IS2147.

d)

Panels shall be free standing, floor mounting type and shall comprise structural frames
enclosed completely with specially selected smooth finished, cold rolled sheet steel of
thickness not less than 3 mm for weight bearing members of panels such as base frame,
front sheets and door frames and not less than 2mm for sides, door, top & bottom
portions. There shall be sufficient reinforcement to provide level surfaces, resistance to
vibration and rigidity during transportation and installation.

e)

All doors, removable covers and panels shall be of gasketed all around with neoprene
gaskets. Ventilating covers, if provided shall have screens and filters. The screens shall be
made of either brass or GI wire mesh.

f)

Design, material selection and workmanship shall be such as to result in neat appearance,
inside and outside with no welds, rivets or bolt head apparent front outside, with all exterior
surfaces tune and smooth.

g)

Metal seals in the form of metal channels properly drilled shall be furnished by the Contractor
along with anchor bolts and necessary hardware for mounting the panels. Panels shall be
mounted on the other end of the channel.

h)

Cable entries to the panel shall be from the bottom. The bottom plates of the panel shall be
fitted with removable gland plates and fixed with cable glands. Necessary number of cable
glands of sizes to suit external cables to the panels shall be supplied by the bidder. Cable
glands shall be screwed type made of brass and shall be suitable for PVC armoured cable.

6.03

that the
equipment
specified
and
such unspecified
required for completeness of protection/control scheme be
the panels without congestion and if necessary to provide
price increase at a later date on this account shall be allowed.

MOUNTING:

a)

All equipment on and inside the panels shall be mounted and completely wired to the
terminal blocks ready for external connection. The equipment of panel shall be mounted
flush.

b)

Equipment shall be mounted such that removal and replacement can be

accomplished individually without interrupting of service to adjacent devices and
are readily accessible without use of special tools. Terminal marking shall be
clearly visible and of permanent nature.

WBSETCL / TECH SPEC / Rev.-1

Page 12 of 104

Control & Relay Panel

c)

The contractor shall carry out cut out, mounting and wiring of the bought out items which are
to be mounted in the panel in accordance with the corresponding equipment manufacturer's
drawings.

d)

The centre line of switches, push buttons and indicating lamps shall be not less than
750 mm from the bottom of the panel. The centre line of relays and meters and recorders
shall be not less than 450 mm from the bottom of the panel.

e)

The centre lines of switches, push buttons and indicating lamps shall be matched to give a
neat and uniform appearance. Likewise the top of all meters, relays and recorders etc. shall
be in one line.

f)

The control switches for circuit breakers and isolators shall be located on the mimic diagram
corresponding to their exact position of the controlled equipment in the single line drawing.
The location of the switches shall be within working height from the floor level for easy and
comfortable operation.

g)

No equipment shall be mounted on the doors.

h)

All the panels in the control room shall be matched with the other panels of the same C&R
board in respect of dimension, colour and appearance. Control equipment on front side of the
panel shall be similarly placed.

i)

All the equipment connections and cabling shall be designed and arranged to minimise the
risk of fire and damage.

6.04
a)
b)

Sl. No.
1

PAINTING:
All unfinished surface of the steel panels and frame work shall be sand blasted to remove
rust, scale, foreign adhering material or grease.
A suitable rust resisting primer shall be applied on the interior and exterior surfaces of the
steel, which shall be followed by of an under coat suitable to serve as base and binder for the
finishing coat. The finishing coat on the exterior of the panel & on the interior faces shall be
as per following table: Painting

Colour

2
3
4
5

Type of Painting
Thickness of Paint
Phosphating
Special
Instruction

WBSETCL / TECH SPEC / Rev.-1

a) External Colour shade

Shade RAL 7032 (Pebble Grey)
b) Internal Colour shade
White
c) External Finish
Texture Semi Glossy
d) Internal Finish
Texture Semi Glossy
e) Base Frame Colour shade
Black
Powder Coating
Average of Powder Coating
80-100 microns
Sheet Steel shall be phosphated in accordance to IS 6005
Small quantity of paint shall be supplied for minor touchup work required
at site.

Page 13 of 104

Control & Relay Panel

6.05

PANEL INTERNAL WIRING:

a)

All wiring shall be carried out with 1100 V grade Single core, standard copper conductor
wires with PVC insulation conforming to IS 694 or equivalent International Standard.

b)

The minimum size of the stranded copper shall be as follows :

i)
ii)
iii)

c)

All current transformer circuit

Voltage transformer circuits
All other circuits

: 2.5 sq mm per lead.

: 2.5 sq mm per lead
: 1.5 sq mm per lead.

The following colour scheme shall be used for the wiring :

Circuit where used
----------------------Red, yellow and blue phase
of instrument transformer
circuit.

Colour of the wire

---------------------Red, yellow and blue for
respective phases.

Neutral connections earthed

or not earthed in the
instrument transformer circuit.

Black

Earthing connection

Green

AC control wiring circuit for

auxiliary AC supply.

Black

D.C. control wiring circuit

using D.C. Battery supply.

Grey

d)

All internal wiring shall be securely supported, neatly arranged, readily accessible and
connected to equipment terminals and terminal blocks. Wiring gutters & trough shall be used
for this purpose.

e)

All wiring interconnecting the front cubicles with the near cubicles of duplex type panel
over the access corridor shall be wired in gutters held against the ceiling of the corridor by
means of screws and the interconnection shall be made through suitable terminal
connectors securely fixed on the panel.

f)

Longitudinal troughs extending throughout the full length of the panel shall be used for inter
panel wiring. Inter connections to adjacent panels shall be brought out to a separate set of
terminal blocks located near the slot of holes meant for taking the interconnecting
wires. All bus wiring for interpanel connection shall be provided near the top of the panels
running throughout the entire length of the panels.

g)

Wiring connected to the space heaters in the cubicles shall have porcelain beaded
insulation over a safe length from the heater terminals.

h)

Wire termination shall be made with solder less crimping type and tinned copper lugs which
firmly grip the conductor and insulation. Insulated sleeves shall be provided at all the wire
terminations. Engraved core identification plastic ferrules marked to correspond with panel
wiring diagram shall be fitted at both ends of each wire. Ferrules shall fit tightly on the wire
and shall not fall off when the wire is disconnected for any purpose. Termination shall be
such that no strand of a conductor shall left loose or overhanging. Conductor termination
shall be secured to the holding nuts/screws, terminal blocks etc. with washers interposed

WBSETCL / TECH SPEC / Rev.-1

Page 14 of 104

Control & Relay Panel

between the terminals/holding nuts/screw heads. The terminals shall be so connected that no
conductor ferrule code gets masked due to overlay of conductors.
i)

6.06

All spare contacts of relays shall be wired up to terminal blocks.

TERMINAL BLOCKS:

a)

All internal wiring to be connected to the external equipment shall terminate an terminal
blocks, preferably vertically mounted on the side of each panel. Terminal blocks shall be
1100 V grade and have 10Amp continuous rating, moulded piece, complete with insulated
barriers, stud type terminals, washers, nuts and lock nuts, inserts. The stud, washers, nuts,
locknuts, inserts shall be tin plated Brass/Brass. Terminal block design shall include markings
of terminals and the terminals shall be provided with transparent plastic, slip on/clip
on terminal covers. Markings on the terminal strip shall correspond to wire number and
terminal numbers on the wiring diagram.

b)

Terminal blocks for current transformer and voltage transformer secondary leads shall be
provided with test links and isolating facilities. Also current transformer secondary leads shall
be provided with short circuiting and earthing facilities of adequate rating.

c)

Each terminal block shall be provided with at least 20% spare terminals on each panel and
these spare terminals shall be uniformly distributed on all terminal block.

d)

In case of duplex panels, separate set of terminal blocks shall be provided with separate
internal cable entries for the front (control) and rear (relay) sections.

e)

Terminal blocks shall be suitable for connecting the following conductors on each side.
i)
All C.T. circuits.
: Two of 4.0 sq.mm. copper.
ii)
All P.T. circuits.
: Four of 2.5 sq.mm. copper.
iii)
AC/DC Power Supply Circuit
: Four of 2.5 sq.mm. copper.
iv)
All other circuits.
: Four of 1.5 sq.mm. copper.

f)

There shall be a minimum clearance of 250 mm between the first row of terminal blocks
and the associated cable gland plate. Also the clearance between two rows of terminal
blocks shall be minimum of 150mm.

g)

The number & sizes of the multicore incoming cable will be as per approved scheme. All
necessary cable terminating accessories such as gland plates packing glands, crimp type
tinned copper lugs, supporting clamps and brackets, wiring troughs and gutters etc. for cable
shall be included in contractor's scope of supply.

h)

All studs, nuts, screw etc. shall be threaded according to IS:7684 or equivalent International
Standards.

6.07

MIMIC DIAGRAM:

a)

Coloured mimic diagram and symbols showing the exact representation of the system shall be
provided in the front of control panels.

b)

Mimic diagram shall be made preferably of anodised aluminium or plastic of approved fast
colour material which shall be screwed on to the panel and can be easily cleaned. The mimic

WBSETCL / TECH SPEC / Rev.-1

Page 15 of 104

Control & Relay Panel

bus shall be 2mm thick. The width of the mimic bus shall be 10mm for bus bars and 7mm for
other connections. Indicating lamp, one for each phase for each bus shall be provided on the
mimic of Bus coupler panel of three Bus system or at Transfer bus panel of two bus system to
indicate bus charged condition.
c)

d)

6.08

Colour scheme for mimic diagram.

KV Class
Colour
-----------------400KV
Dark Violet
220 KV
Light orange
132 KV
Signal Red
33 KV
Brilliant green
11 KV
Air Craft blue
400/230 V
Black
Earth
White
110 V
Canary yellow

Shade Index as per ISS

---------------------796
557
537
221
108
309
-

LED Position Indicators, Round type, for all earth switches & isolators control switches and
discrepancy type control switch with flash type built-in indicating lamp, for circuit breakers
shall be mounted along the mimic diagram at appropriate location in 400KV, 220 KV and 132
KV duplex type C&R panels.
In 33 KV simplex type C&R panels, LED Position Indicators for the position indication of
isolators, earth switches and ON/OFF indication for such breaker shall be mounted along
the mimic diagram at appropriate location.

NAME OF IDENTITY PLATES:

a)

All instruments, relays and such other similar electrical devices mounted on the control and
relay panel shall be provided with name plates bearing the manufacturer's name, serial
identifying number and the Electrical rating data.

b)

25mm wide plastic plates bearing suitable identification marks shall be fixed under the
terminal wiring at the test blocks, at the fuse blocks and at the cable terminals. Similar plates
shall be fixed on the exterior of the switch board in appropriate places to indicate function of
control switches, push button etc. such as isolator control switch, breaker control switch, DC
fail test, accept reset etc. Suitable identification marks shall be provided for individual casing
part of the relays and other equipment.

c)

50mm wide plastic plate bearing suitable circuit description (which will be furnished after
order is placed) etched in 30 mm size letters shall be provided for each panel and mounted
on the top of both outer and inner sides of the front and rear panels. These plates shall be
removable type.

d)

Each unit of control and relay panel shall be provided with a label located at the bottom on
the front and shall contain the following details:
i)
Manufacturer's name
ii)
P.O.no. and date
iii)
Drg. ref. no. that pertains to the panel.

WBSETCL / TECH SPEC / Rev.-1

Page 16 of 104

Control & Relay Panel

6.09

CONTROL AND RELAY BOARD PANEL LIGHTING & ACCESSORIES:

a)

Each unit of cubicle interior (both control and relay panel) shall be illuminated by CFL
connected to 230V single phase AC through individual switch for duplex type panel and
through Door switch for Simplex type panel. The illumination of the interior shall be free from
hand shadows and shall be planned to avoid any strain or fatigue to the wireman likely to be
caused due to subnormal or non uniform illumination. One emergency D.C. light (CFL) shall
also be provided for each relay panel with individual switch with proper identification mark.

b)

Corridor of the duplex type control and relay board formation should be illuminated with
adequate no. of Compact fluorescent lamps, AC operated, through door operated push button
switch provided at both sides.

c)

One 15 amps. 3 pin power socket outlets together with plug pins shall be provided at
convenient points in each panel with marking at the bottom for obtaining AC supply wherever
required.

d)

The above AC auxiliary supply and DC emergency lamp ckt. in each panel shall be HRC fuse
and link protected.

6.10

SPACE HEATERS:
Tubular space heater suitable for connection to the single phase AC supply in each panel
(both control and relay panel in case of duplex type) complete with switches and
thermostat located at convenient position shall be provided at the bottom side of the
cubicle to prevent condensation of moisture. The watt loss per unit surface temperature
of the heater shall be low enough to keep surface temperature well below allowable
heat.
The wattage of the heater shall be such as to keep 10 C above average ambient
temperature in the rainy season but the temperature shall not under any circumstances
damage the insulation of the wiring of the panel.

6.11

SAFETY EARTHING:

a)

All panels shall be provided with an earth bus securely fixed along with the inside base of
the panel extended throughout the length of the C&R board formation. The material and
size of the earth bus bar shall be 25mm x 6mm size copper. Provision shall be made for
extending the earth bus bars at a future date into new adjacent panels to be installed if any.
Provision shall be made at the end panels for connecting the same to the system earth grid
mat.

b)

Earthing of current free metallic parts or metallic bodies of the equipment provided in the
switchboard shall be done with soft drawn conductor of size not less than 2.5 sq.mm.

c)

The neutral point of star connected LV winding of instrument transformers and one corner of
the open delta connected LV side of instrument transformers shall be similarly earthed with
the main earth bar of the switchboard earthing system.

WBSETCL / TECH SPEC / Rev.-1

Page 17 of 104

Control & Relay Panel

6.12

FUSES AND LINKS:

H.R.C. Cartridge fuse and link of adequate current and voltage rating shall be provided inside
the cubicle in an easily accessible location. The selection of the main and sub circuit fuse
ratings shall be such as to ensure selective clearance of sub circuit faults. Fuses shall have
operation indicators for indicating blown fuse condition. Fuse carriers and bases shall have
imprints of rating, voltage and circuit designation.

7.00

INDICATING LAMPS:

a)

These lamps shall be of LED type and suitable for being operated on S/S D.C. voltage or AC
voltage or P.T. secondary supply as and where applicable. All Lamps shall be interchangeable,
panel mounting type with rear terminal connection and shall afford easy replacement from
the front of the panel. Lamps shall have translucent lamp covers to diffuse lights and
coloured Red, green, Amber, clear white or blue as specified. The lamp cover shall be of
screwed type, unbreakable and mounded from heat resisting material. The indicating lamps
with resistors shall withstand 120% of rated voltage on a continuous basis.

b)

No tools shall be required for replacing the bulbs and lenses.

c)

The colour scheme of the signal lamps shall be as follows :

8.00

Function
---------C.B. spring charged/compressor
healthy indication

Colour lens
----------Blue

C.B. Trip circuit healthy

White

Alarm Bus and incoming D.C. fail

indication.

Amber

P.T. supply healthy indication

(Bus bar healthy indication).

Red/Yellow/Blue

Isolator ON-OFF Indication

Red/Green

CONTROL SWITCHES:

a)

All control switches shall be of the rotary type provided with escutcheon plates clearly marked
to indicate status of the switch. They shall be semi flush mounted with only the switch front
plate and operating handle projected out. All such control switches shall be provided for
remote operation of isolators and circuit breakers.

b)

All Control switches shall be wire connected at the back. The contact mechanism shall be cam
operated. The contacts shall be silver faced and designed for liberal rating of the duty
involved. The contacts shall be provided with dust and vermin proof removable protection
cover. The protection cover shall preferably be of transparent, inflammable material made of
moulded dielectric material. Springs to be provided in the switch shall not be used as current

WBSETCL / TECH SPEC / Rev.-1

Page 18 of 104

Control & Relay Panel

carrying parts. The contacts provided in the switch shall be suitable for easy
assembly/disassembly during replacement of the contacts. The control switch springs shall be
strong to prevent any inadvertent operation due to a light touch on the handle.
c)

Control switches for 400KV, 220KV & 132KV circuit breakers shall be of discrepancy type with
built in pilot lamps and having two maintained contact positions for "ON" and "OFF" positions
and two momentary contact positions for "ON" and "OFF" impulse. The built-in pilot lamp
shall give a steady light when the position of the control switch corresponds to the position of
the associated circuit breaker. A flickering light shall be given by the same lamp when due to
hand operation or due to automatic tripping of the circuit breaker the position of the control
switch does not coincide with that of the corresponding circuit breaker. The arrangement to
provide the flickering voltage for the above purpose shall be made by the contractor. In order
to avoid continuous burning of the aforesaid built-in lamps associated with the control
switches, the said lamp shall be connected through a switch. The circuit should be such that
irrespective of the position of the aforesaid switch winking of the lamp shall not be affected
by change in respective control switch position. The winking of the control switch pilot lamp
shall be followed by an alarm annunciation after a preset time adjustable between 0-10 secs.
Switches complete with accessories for the above function shall be supplied.

d)

Control switches for 33KV circuit breakers, 400KV, 220KV isolators, 132KV isolators shall be
with pistol grip type operating handle having "ON & OFF" monetary operating position and an
automatic return to normal neutral position on release from operated positions.

9.00

SELECTOR SWITCHES AND CHANGE OVER SWITCHES:

a)

Instrument selector switches shall be provided for indicating instruments while change over
switches shall be provided for selective operation of controls such as auto/non auto reclose,
trip circuit transfer from main breaker to transfer breaker. Protection selector switches to be
provided in the Bus transfer bay shall be used for adopting the bus transfer bay
protection during Bay transfer. Condition when line side C.T. operated protection of any
bay develops any defect. All these switches shall be stay put type.

b)

Voltmeter selector switch shall be suitable for reading all line to line and line to neutral
voltage for effectively earthed system. This selector switch shall be of the rotary oval head or
knob type.

c)

Trip circuit transfer switch shall be of 3-position Normal-Inter-Transfer. Operating handle shall
be pistol grip, lockable at Normal position and key trapped at transfer position having one
common key for all 400KV, 220KV, 132KV and 33KV panels respectively for a particular Substation.

d)

Protection selector in Bus Transfer bay shall be lockable type, two/three position depending
upon scheme requirement.

e)

One four position selector switch for setting group selection in respect of distance relay in Bus
Transfer panel shall be provided.

f)

One three position selector switch for setting group selection in respect of numerical over
current & earth fault relay in Bus Transfer panel shall be provided.

g)

One five position Selector Switch for Earthing Transformer selection in each 33KV side
transformer C&R panel shall be provided.

WBSETCL / TECH SPEC / Rev.-1

Page 19 of 104

Control & Relay Panel

10.00 SYNCHRONISING SWITCH:

a)

Synchronising switch with lock feature two positions, "ON & OFF" shall be provided on all
control panels except the 132/33KV Transformer panel and 33KV C&R panels. The switch
shall be semi flush mounting type.

b)

The switch shall be wired back connected. It's operation in the "ON position shall connect
the incoming and running bus potentials to the respective synchronising instrument and relay
mounted in a trolley, through a synchronising socket having sufficient nos. of ways. The
wiring between the synchronising switch, socket and the main breaker control switch shall be
such that when the main breaker control switch is operated to close position, the breaker
shall not receive a close command unless the synchronising switch is put to the 'ON' position
and receives a synchronising command. If the synchronising trolley is not within the scope of
supply for a particular sub-station, the terminal of the synchronising socket to be shorted
through a plug to be provided to cover the socket.

11.00 PUSH BUTTON SWITCHES:

a)

Push button switches, provided where required, shall be of the monetary contact type wired
back connected. They shall be semi flush mounted. They shall be provided with integral
inscription plates engraved with their functions.

b)

All push buttons shall be with a set of NO/NC contacts as required to fulfill the scheme
requirement. The contact faces shall be silver plated and shall able to make/break and carry
the rated current appropriate to the duty of the desired function.

12.00 INDICATING INSTRUMENTS, RECORDERS & TRANSDUCERS:

All instruments, meters, recorders and transducers shall be enclosed in dust proof, moisture
resistant, black finished cases and shall be suitable for tropical use. All megawatt, megavar,
Bus voltage and frequency indicating instruments shall be provided with individual
transducers and these shall be calibrated along with transducers to read directly the primary
quantities. They shall be accurately adjusted and calibrated at works and shall have means of
calibration check and adjustment at site. The supplier shall submit calibration certificates at
the time of delivery. However no separate transducers are envisaged for digital bus
voltmeters and digital frequency meters and the indicating meters provided in the
synchronising equipment.

12.01 INDICATING INSTRUMENTS:

a)
b)
c)

Unless otherwise specified, all electrical indicating instruments shall be of digital type suitable
for flush mounting.
Instruments shall have 4-digit display; display height being not less than 25 mm
Instrument shall confirm to relevant IS and shall have an accuracy class of 0.5 or better. Watt
and Var meters shall have an indication of (+) and (-) to indicate EXPORT and IMPORT

WBSETCL / TECH SPEC / Rev.-1

Page 20 of 104

Control & Relay Panel

d)
e)

respectively.
Digital voltage and frequency meters shall be of class: 0.5 and shall have digital display of 5
and 4 digits respectively, with display size, not less than 25mm (height).
All indicating instruments shall preferably of size 72mm X 144mm.

12.02 TRANSDUCERS:
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
k)
l)
m)
n)

Transducers (for use with Indicating Instruments and Telemetry/Data Communication

application) shall in general conform to IEC:688-1
The transducers shall be suitable for measurement of active power and reactive power in
three phase four wire unbalanced system.
The input to the transducers will be from sub-station current & potential transformers. The
output shall be in milli ampere D.C. proportional to the input & it shall be possible to feed the
output current directly to the telemetry terminal or indicating instruments.
The transducer characteristic shall be linear throughout the measuring range.
The transducer output shall be load independent.
The input & output of the transducer shall be galvanically isolated.
Each transducer shall be housed in a separate compact case and have suitable terminals for
inputs & outputs.
The transducers shall be suitably protected against transient high peaks of voltage & current.
The transducer shall withstand indefinitely without damage and work satisfactorily at 120% of
the rated voltage and 120% of the rated input current as applicable.
The active & reactive power transducer shall have dual output of 4-20mA.
The response time of the transducers shall be less than 1 second.
The accuracy class of transducers shall be 0.5 or better for watt/VAR transducer.
The transducers shall have a low AC ripple on output less than 1%.
The transducers shall be suitable for load resistance of 1000-1500

12.03 INTELLIGENT ELECTRONIC METER:

Supply of Intelligent Electronic Meters of different classes and different voltage levels shall
not be within the scope of supply of the bidders. However necessary complete wiring
arrangement for Intelligent Electronic Meters along with supply of TTB & Terminal Block shall
be within the scope of supply of the bidders. Terminal Block to be provided for Meter
connection should be De-linked type.

13.00 TEST BLOCK:

Switch Board type, back connected, test blocks with contacts shall be provided with links or
other devices for shorting terminals of CT leads before interrupting the normal circuit for
injection from
external source or for inserting testing instruments in the circuit without
causing open circuit of the CT. The potential testing studs shall preferably be housed in block
molding insulation and partition shall be provided to prevent accidental short circuit across
the studs. Test blocks for meters, relays shall be placed in front and rear panel respectively.

WBSETCL / TECH SPEC / Rev.-1

Page 21 of 104

Control & Relay Panel

14.00 DC, AC AUXILIARY SUPPLY AND V.T. SECONDARY SUPPLY DISTRIBUTION

SCHEME:
14.01 DC CIRCUIT FOR 400KV SYSTEM:
a)

Two sets of batteries (220v), their respective chargers and DC boards shall be used for DC
supply to each 400KV control relay and protection panels as DC supply 1 and DC supply-2.
Necessary arrangement for Supervision of both the incoming DC Supplies shall be made.

b)

In each duplex type 400KV C&R panel, following circuits shall be connected to DC Supply 1
through suitable MCBs/ HRC fuses:
i)
Isolator control circuit
ii)
Synchronising circuit
iii)
Metering circuit
iv)
Indication circuit
v)
Annunciation circuit
vi)
CB Closing circuit
vii)
VT Selection circuit & CB Aux. Relay circuit
In case of failure of DC Supply 1, the above circuits will be fed from DC Supply 2. Changeover
can be Automatic (by using changeover contact of power contactor)/Manual (by using
Selector switch).

c)

DC supply 1&2, drawn to each duplex type 400KV C&R panel, shall be divided into the
following sub circuits. Each sub circuit shall be controlled and monitored with the help of
suitable MCBs/HRC Fuses.
i)
CB Trip coil 1 shall be fed from DC supply 1.
ii)
CB Trip coil 2 shall be fed from DC supply 2.

d)

DC Supply -1&2 shall be fed to Protection panel from C&R panel directly. Necessary
arrangement for Supervision of both the incoming DC Supplies shall be made. DC supply
1&2 shall be divided into the following sub circuits. Each sub circuit shall be controlled and
monitored with the help of suitable HRC Fuses.
i)
Circuitry for Main 1 protection, over voltage protection and reactor gr.-A protection
shall be fed from DC supply 1.
ii)
Circuitry for Main 2 protection and reactor gr. B protection shall be fed from DC
supply 2.

e)

Annunciation DC shall be supervised by the Annunciator through auxiliary AC supply of the

Annunciator in each panel.

14.02 D.C. CIRCUIT FOR 220 KV SYSTEM C&R PANEL:

a)

b)

There shall be one DC incomer (220V) for each control and relay panel of 220KV system
voltage, fed from D.C. distribution board through a 32Amp. switch fuse unit provided there.
Necessary arrangement for Supervision of the incoming DC supply for each panel shall be
made. One 16 Amp. rating HRC fuse unit both at +ve and -ve side shall be provided for
the D.C. incomer in each panel of 220 KV system.
DC supply in individual panel shall be distributed within the panel as below :
i)
ii)

C.B. remote closing, local operation circuit including auxiliary relay function, C.B.
remote and protection trip to trip coil 1 with trip circuit supervision relay shall be
through HRC fuse and link.
C.B. remote and protection trip to trip coil 2 with trip circuit supervision relay through
HRC fuse and link.

WBSETCL / TECH SPEC / Rev.-1

Page 22 of 104

Control & Relay Panel

iii)
iv)
v)
vi)
vii)

Protective relay and P.T. selection circuit with D.C. supervision relay through HRC
fuse both at +ve and -ve side.
Indication circuit through HRC fuse and link.
Isolator control circuit through MCB.
D.C. emergency lamp circuit with HRC fuse and link.
D.C. supply to synchronising socket through links both at +VE & -VE side.

D.C. annunciation bus shall also be teed off from the incomer D.C. bus of 220KV Bus
Coupler/Bus Transfer Panel for 220KV annunciation system through 6A HRC fuse both at +ve
and -ve side and the same shall run continuously through the entire C&R board for facia
annunciation system in respective panels. In addition, Annunciation DC shall be supervised by
the Annunciator through auxiliary AC supply of the Annunciator in each panel.

14.03 D.C. CIRCUIT FOR 132 KV AND 33 KV SYSTEM C&R PANEL:

a)

There shall be only one DC incomer (220V) for the entire control and relay panel of 132KV
and 33KV system voltage fed from D.C. distribution board through a 32Amp. switch fuse unit
provided there. One 16Amp. rating HRC fuse unit both at +ve and -ve side shall be provided
for the D.C. incomer in Bus Transfer (2 bus system)/ Bus Coupler (3 bus system) panel of
132KV and 33KV system. The above D.C. incoming bus of 132KV and 33KV CR Panel only
shall run continuously in the control and relay board of each system voltage. Individual panel
D.C. supply for breaker control, isolator control, supervision and indication of circuit breaker
and other protective equipment etc. shall be teed off in each panel from the above D.C. bus
through a set of links.
D.C. annunciation bus shall also be teed of from the incomer D.C. bus of 132 KV and 33
KV Bus Transfer (2 bus system)/ Bus Coupler (3 bus system) panel for 132 KV and 33 KV
annunciation system through 6A HRC fuse both at +ve and -ve side with necessary D.C.
supervision relays and the same shall run continuously through the entire C&R board of
each system voltage for facia annunciation system in respective panels. In addition,
Annunciation DC shall be supervised by the Annunciator through auxiliary AC supply of the
Annunciator in each panel.

b)

DC supply to individual panel thus teed off through links shall be distributed within the panel
as below:
i)
ii)
iii)
iv)
v)
vi)
vii)

C.B. remote closing, local operation circuit including auxiliary relay function, C.B.
remote and protection trip to trip coil 1 with trip circuit supervision relay shall be
through 10A HRC fuse and link.
C.B. remote and protection trip to trip coil 2 with trip circuit supervision relay through
10A HRC fuse and link.
Protective relay and P.T. selection circuit with D.C. supervision relay through 10A
HRC fuse both at +ve and -ve side.
Indication circuit through 6A HRC fuse and link.
Isolator control circuit through 10A HRC fuse and link.
D.C. emergency lamp circuit with 2A HRC fuse and link.
D.C. supply to synchronising socket through links both at +VE & -VE side.

14.04 D.C. CIRCUIT FOR GIS SYSTEM C&R PANEL:

There shall be one DC incomer (220V) for each control and relay panel of GIS system, fed
from D.C. distribution board through a 32 Amp. switch fuse unit/MCB provided there.
Necessary arrangement for Supervision of the incoming DC supply for each pane shall be

WBSETCL / TECH SPEC / Rev.-1

Page 23 of 104

Control & Relay Panel

made. From control panel the DC supply will be teed off from the incomer D.C. bus to LCC
panel. For remote operation of GIS equipment the operational DC will generate from LCC
through LOCAL/REMOTE switch of LCC.
14.05 AC CIRCUIT:
a)

230V, single phase 50Hz AC auxiliary supply to the control, relay and protection panel board
of each system voltage 400KV, 220KV, 132KV and 33KV will be fed from AC distribution board
through separate 32Amp. switch fuse units provided there. The supply shall be provided in
Bus coupler/Bus Transfer panel. A continuous AC bus shall be provided at the control, relay
and protection panel board of each group wherefrom AC supply to each panel shall be teed
off through a set of links. One 16Amp rated HRC fuse units shall be provided for a complete
control, relay and protection panel board of each system voltage for the incoming AC supply.
A set of fuse and link rated for 10Amps. for 3 pin plug circuit, cubicle lamp circuit, space
heater circuit shall also be provided in each control, relay and protection panel.

b)

Door operated corridor illumination lamp ckt. of duplex type panel shall be arranged from the
above incoming AC bus through suitably rated fuse and link.

c)

AC circuit for incoming DC Annunciation DC fail alarm scheme shall be provided in the Bus
coupler panel of 400KV & 220 KV system and in the Bus Transfer (2 bus system)/ Bus
Coupler (3 bus system) panel of 132KV and 33KV system. The above circuit shall be teed off
from the above respective panel AC bus through fuse and link suitably rated.

d)

One supervision relay for incoming AC fail with test P.B. and reverse flag indication shall be
provided for monitoring of AC supply healthiness through D.C. operated facia annunciation of
Bus Coupler panel of 400KV & 220KV system and of the Bus Transfer (2 bus system)/ Bus
Coupler (3 bus system) panel of 132KV and 33KV system.

14.06 V.T. SECONDARY SUPPLY DISTRIBUTION SCHEME:

PT kiosk at switchyard may be considered with sufficient terminals, fuses, links etc for
protection PT secondary supply and for metering PT secondary supply to bus coupler panel
through individual cable for all voltage class in a substation.
a)
b)

c)
d)
e)
f)

The bus coupler panel shall receive protection VT secondary volts through fuses and links
provided in the respective VT kiosk. The protection VT supply shall run throughout entire
board for each panel through VT supply selection scheme.
The Bus Coupler panel shall also receive Metering VT Secondary volts by at least 25Sqmm
Copper/ equivalent Aluminum per phase/neutral through fuses and links provided in the
respective VT kiosk. The Metering VT supply shall also run throughout entire board for each
panel through VT supply selection scheme.
For 400KV/220KV system three sets VT selection relays operated from DC supply-1/ change
over DC system If VT selection relay is latched type, change over DC system of the respective
panel can be used to energize all the three VT selection relays.
Selected VT secondary supply to the protective relays of each panel shall be fed through
individual fuses in individual phases and link in neutral in each panel. Necessary arrangement
for supervision of VT secondary supply shall be provided in numeric relay.
Selected VT secondary supply to metering and indicating instruments of each panel shall be
fed through MCB. Proper arrangement of supervision through MCB shall also be provided.
In 132KV C&R panel, where more than one set of 132KV PT is available or not, necessary
132KV PT selection scheme shall be adopted and made ready for future use and where more
than one set of 33KV bus PT is available, necessary 33KV PT selection scheme shall be
adopted through switch at 33KV C&R panel.

WBSETCL / TECH SPEC / Rev.-1

Page 24 of 104

Control & Relay Panel

15.00 ANNUNCIATION SYSTEM:

15.01 INCOMING DC FAIL AND ANNUNCIATION BUS D.C. FAIL ALARM SCHEME:
a)

400KV system shall have alarm scheme, as follows: i)

Incoming DC-1/DC-2 supervision shall be provided in each panel.
ii)
In each panel, Annunciation DC Fail indication at Annunciator, which is fed by AC
supply.
iii)
In each Protection panel, DC-1/DC-2 fail supervision shall be provided.
iv)
In Bus bar protection panel, DC fail supervision shall also be provided.
v)
Audible AC alarm shall be provided for Incoming DC/Annunciation DC Fail.
vi)
The "Annunciation Bus D.C. alarm scheme" shall be common to the entire C&R
board and operated from 230V single phase AC auxiliary supply for audible as well as
visual alarm through lamp and bell arrangement. The scheme shall comprise of D.C.
supervision relays with test push buttons for Annunciation bus DC system, AC
operated alarm accept relays, indication lamps, AC operated hooter and push
button for cancellation of audible alarm, as necessary.

b)

220KV system shall have alarm scheme, as follows: i)

Incoming DC supervision shall be provided in each panel.
ii)
At Bus Coupler panel, Annunciation DC Fail supervision shall be provided. The
supervision scheme shall be operated from 230V single phase AC auxiliary supply for
audible as well as visual alarm through lamp and bell arrangement. The scheme shall
comprise of D.C. supervision relays with test push buttons for Annunciation bus DC
system, AC operated alarm accept relays, indication lamps, AC operated hooter
and push button for cancellation of audible alarm, as necessary.
iii)
In each panel, Annunciation DC Fail indication at Annunciator, which is fed by AC
supply.
iv)
In Bus bar protection panel, DC fail supervision shall also be provided.

c)

132KV and 33KV system shall have a "Incoming DC fail and Annunciation Bus D.C. alarm
scheme", as follows: i)
This will be provided at the Bus Coupler/ TBC panel & will be common to the entire
C&R board of each system voltage.
ii)
The scheme shall be operated from 230V single phase AC auxiliary supply for audible
as well as visual alarm through lamp and bell arrangement. The scheme shall
comprise of D.C. supervision relays with test push buttons for incoming DC supply
and Annunciation bus DC system, one AC operated alarm accept relays, one
indication lamp, one AC operated hooter and one push button for cancellation of
audible alarm.

15.02 OTHER TRIP AND NON-TRIP ALARM SCHEME:

a)

Facia annunciation system shall be provided in each control panel by means of visual and
audible alarm to draw attention of the operator to the abnormal operation or operation of the
protective devices. The annunciation shall be divided into the following categories:
i)
ii)

Trip annunciation
Non Trip annunciation

The annunciator shall be suitable for operation with the sub-station AC/DC voltage and
potential free initiation contact is to be provided.

WBSETCL / TECH SPEC / Rev.-1

Page 25 of 104

Control & Relay Panel

b)

The visual facia widow shall be flush mounted at a convenient position near top row of the
control panel and necessary switching relays for the same shall be mounted inside the panel
or at the relay side of the panel.

c)

The annunciator facia shall be provided with translucent glass or plastic cover plates of white
colour with inscription in black colour. The size of facia window shall be 70mm x 35mm in
general and the size of the lettering shall not less than 5 mm. Alarm inscription shall be
engraved not more than three line of in each facia window and the same shall be prominently
visible when facia light is ON. The cover plates of the facia window shall be easily removable
to facilitate replacement of lamp when required.

d)

The transparency of cover and wattage of the lamp provided in the facia window shall be
adequate to ensure clear visibility of the inscription from the location of the operator's table in
the control room having high illumination intensity. Each facia window shall be provided with
two lamps to ensure safety against lamp failure. Long life lamp shall be used having resistor
of adequate rating in series.

e)

Accept, Reset and lamp Test push buttons for acknowledgment of alarm, reset of visual
indication and for checking perfectness of the lamps shall be provided below the facia window
in each panel. These push buttons shall be common for both trip and warning annunciation.
The sequence of operation of the annunciation shall be as follows:
Alarm Condition
--------------i) Normal
ii)Abnormal

Fault
contact
------Open
Close

Visual
Annunciation
-----------OFF
Flashing

Audible
Annunciation
-----------OFF
ON

iii)Accept push button

is pressed.

a) Close
b) Open

Steady ON
Steady ON

OFF
OFF

iv) Reset push button

is pressed.

a) Close
b) Open

ON
OFF

OFF
OFF

Steady ON

OFF

v) Lamp test push

button is pressed.

Open

f)

In case static annunciation system is used, care should be taken that no spurious alarm
condition arises due to external influences on the annunciator wiring and switching
disturbances from the
neighboring circuits within the panels. The static relay shall be
suitable for operation within a temperature range from 0C to 55C.

g)

The annunciation scheme should be such that momentary closing of any fault contacts shall
also cause operation of annunciation system as above.

h)

The annunciation scheme wiring should be such that the warning annunciation facia window
can be converted to trip annunciation facia window or vice versa with the change in audible
alarm connection accordingly, at site easily.

15.02.01 TRIP ANNUNCIATION:

Trip annunciation shall be used to draw attention of the operator when the circuit breaker is
tripped automatically through relay. Audible common annunciation for the entire board
formation of each system voltage shall be provided by a hooter. The visual annunciation shall

WBSETCL / TECH SPEC / Rev.-1

Page 26 of 104

Control & Relay Panel

be provided by flickering of a window facia of a group of facia window to be provided in each

panel.
15.02.02 NON-TRIP ANNUNCIATION:
Non-Trip annunciation shall be used to draw attention of the operator to abnormal operating
condition of certain equipment for immediate action to avoid tripping of circuit breaker.
Audible annunciation shall be provided by means of a separate common bell with different
tone and visual annunciation by flickering of a facia window.

16.00 RELAY:
GENERAL REQUIREMENT:
The main numerical protective relays shall be of Panel manufacturers own
make or their principal companys make.
Live demonstration of any offered relay has to be arranged by the Party at the laboratory of
Central Testing Department of WBSETCL, if felt necessary by WBSETCL before finalisation of
bid.
16.01 All shall conform to the requirement of IS: 3231 / IEC 255 and shall be suitable for operation
within a temperature range 0C to 55C and 50% to 95% relative humidity. Relays shall be
suitable for flush/ semi flush mounting on the panel with connections from the rear, protected
with dust tight cases for tropical use and with transparent cover removable from the front.
16.02 All protective relays shall be in draw out case or plug-in/modular cases with proper built in
testing facilities. If testing devices are not incorporated in the relay itself separate test block
and switches shall be provided. The adjusting devices shall be accessible with the relay
mounted on the panel board. Flag type operating indicators and flag indicator reset devices
shall be provided which shall be suitable for operation from the front of the relay case without
opening the cover.
16.03 All A.C. relays shall be suitable for operation at 50Hz.The current coils shall be rated for a
continuous current of 1 amp and the voltage coil for 110V normal. The contacts of the relays
shall be properly designed to prevent or minimise damage due to arcs which have to be
broken successfully against 220 +/- 10% volt DC. When open the contacts shall withstand a
voltage of 115% of the normal circuit voltage. The relays shall be designed for satisfactory
operation between 70% and 110% of rated D.C. voltage of the sub-station. The voltage
operated relays shall have adequate thermal capacity for continuous operation.
16.04 Timers shall be of static type. Pneumatic timers are not acceptable.
16.05 The sub-stations may be required to run without air-conditioning plant. Therefore, the static
relays shall be designed for operating satisfactorily under the climatic conditions of
ambient temperature and relative humidity variation from 0C to 55C and 50% to 95%
respectively. The static relays should be capable to withstand the test voltages as stated in
the relevant Indian standard or equivalent. Stringent measures including shielding of long
internal wiring should be taken to make the relays insensitive to the voltage spikes. Insulation
barriers shall be provided to ensure that transients present in CT & VT connection due to
extraneous sources do not cause damage to static circuits.

WBSETCL / TECH SPEC / Rev.-1

Page 27 of 104

Control & Relay Panel

16.06 DC/DC converter shall be provided in the solid state protective relays wherever necessary in
order to provide a stable auxiliary supply for relay operation. Provision of D.C. Cells in the
protective relays as reliable standby power supply will however not be acceptable. The DC/DC
converter shall have power supply failure annunciation contact.
16.07
a)
The solid state relays shall be stable and suitably protected against transient/induced over
voltages and noise signals. The bidder shall state clearly in his list of special requirement, if
any, for D.C. input arrangement or cabling considered necessary for satisfactory operation of
solid state relays quoted by him.
b)
i)
All the Numerical Relays should have setting parameter access restriction. All the
numerical relay should have provision for setting all the features available in the
relay and viewing those setting as well as different other parameters through both
built in display unit as well as through PC. The supply of relay should be inclusive of
necessary software and hardware for interfacing with a PC., to be supplied by the
bidder. The bidder/manufacturer has to make arrangement for multiplexing the
quoted relays substation wise through LAN configuration via Ethernet switch and
IEC 61850 rear port for communication with all relays, along with supply of cables,
connectors, communication port, converters etc. as necessary for downloading the
storage data for all microprocessor/ numeric relays, disturbance recorder and fault
locator etc. through a centralized PC. The necessary PC, window based Licensed
software along with operating system software and all the necessary hardware for
establishing the Network in IEC 61850 platform to be considered in the scope of
supply by the bidder.
Bidder shall arrange for such local man to machine communication facility for
all the numerical relays inclusive of all the necessary accessories as mentioned
above complete through Local Area Networking System for each 400KV, 220KV &
132KV substation wherever mentioned in the schedule.
For existing and new substations, provision is to be made for connectivity with the
existing and or future numerical relays through PC by providing external comport
multiplier (e.g. Rocket port/Serial sharer etc.).
ii)

All the protective relays shall be numerical type and communication protocol shall be
IEC 61850 compatible. All the numerical relays shall have one front port for direct
access with proprietary protocol and rear port with IEC 61850 protocol. The main
Numerical Protective Relays shall also have a IRIG-B port in addition to the above
ports to synchronise the internal clock with GPS based time synchronising equipment
directly through its own IRIGB port.

iii)

All numerical relays shall be provided with Relay Failure Annunciation Contact.

c)

List of software for local parameterisation, settings, logic configuration, data retrieval,
disturbance evaluation, downloading of storage data and no. of license (minim. 3 for new
400KV & 220KV S/Stn, & one each for other substations involved) shall be supplied by the
bidder.

d)

Interconnection architecture among the relays showing details identification of all

intermediate hardware including interfacing port of the monitoring PC and other hardware

e)

Connectivity architecture of Disturbance recorder evaluation station of all numerical relays

like numerical distance relay, numerical differential relay etc. with time synchronisation unit
(applicable for 400KV & 220KV substation only).

WBSETCL / TECH SPEC / Rev.-1

Page 28 of 104

Control & Relay Panel

f)

Interface architecture involving multiple nos. of numerical relays of respective make, with the
monitoring PC.

g)

Interface architecture of the above network with existing/future network of other make
numerical relays with monitoring PC, wherever applicable.

h)

The bidder has to furnish the certificate for IEC 61850 Compliance from KEMA/CPRI,
type test certificate from any Govt. recognized Test House and performance certificate from
Power Utilities in India.

i)

Local area networking system: i)

ii)
iii)
iv)
v)
vi)

PC

configuration for both local and remote end communication:

CPU - i5 latest (3GHz Min)
RAM 4GB Min
HDD 320GB, 7200 rpm
Internal DVD combo
17 TFT monitor, Key board & optical mouse
Minimum 2 nos COMPORT(RS232C)
8 Nos. USB Port (2 Front & 6 Rear)
Requisite quantity of interconnecting cable
IRIGB port if required for time synchronization with GPS clock for date and time
stamping.
Operating system Windows XP/ Windows 7
Required software
External comport (RS232C) multiplier to be interfaced with the comport of PC, having
minimum 8 nos interfacing port.
UPS - ON LINE UPS for individual PC with minimum 15 min. battery backup.
Printer Colour inkjet suitable for A3 size paper.
Required furniture for table top installation of PC along with Printer and two nos
suitable revolving chair
Other particulars, if any.

16.08 NUMERICAL TYPE DISTANCE PROTECTION SCHEME RELAY:

[The relay should be IEC61850 compliant having rear port compatible to IEC
61850 protocol.]
a)

The distance protection shall be a microprocessor based high speed non-switched distance
relay suitable for all phase to phase faults and phase to earth faults based on numerical
principles. It shall also have necessary phase selection and direction selection facilities. The
relay shall be field selectable for various permissive over reaching, permissive under reaching
and for blocking/ intertripping through communication schemes.

b)

The relay shall have polygonal/ quadrilateral characteristics with a facility to set resistance
and reactance characteristics independently.

c)

The relay shall have three forward and one reverse zone of protection for each PH-PH & PH-E
fault loop with sufficient impedance or reactance and resistance reach of each zone. It shall
have three zone time stepped characteristics. The second and third zone elements shall
provide backup protection in the event of the carrier protection on the first zone element
failing to clear the fault.

d)

It shall be compatible with the PLCC equipment to be procured separately under separate
contract. The distance protecting scheme shall be suitable for any length (short length also

WBSETCL / TECH SPEC / Rev.-1

Page 29 of 104

Control & Relay Panel

i.e. Minimum Settable value should be 1 Primary) of transmission line. Any limitation in this
regard shall be clearly specified by the bidder.
e)

The relay shall have numerical filtering and measuring techniques. It shall have individual
measuring element for each phase to phase fault and each phase to earth fault. It should
ensure a maximum operating time from the relay to the trip coil of CB within 40 ms for all
types of faults at 50% of the set zone 1 relay reach with CVT being used on the line for a
System Impedance Ratio (SIR) of 4 and the same shall be 45millisecond for an SIR of 15.
However, a relaxation of 5millisecond is allowed for the relays being used for 132 KV.

f)

It shall be provided with continuous self supervision features along with self diagnostic
feature, having output IRF contact for annunciation purpose.

g)

Shall have memory circuits with defined characteristics in all three phases to ensure correct
operation during close up three phase faults and other adverse conditions and shall operate
instantaneously when circuit breaker is closed to zero volt three phase faults.

h)

It shall be suitable for single and three phase tripping mode to be scheduled by WBSETCL
depending upon their application along with necessary trip relays.

i)

The scheme for 400KV & 220 KV system shall be suitable for single phase or/and three phase
Auto-reclosing. It shall have in built features of weak end in feed, switch on to fault, fuse
failure supervision and instantaneous blocking of protection in the event of fuse failure and
should remain inoperative for system earth fault, Power Swing blocking with zone selection
facility for such blocking, broken conductor detection and different indications for relay
monitoring operations.

j)

The relays shall have the provision for Man to Machine Communication for local and
remote control and monitoring complete with software, ports and other hardware e.g.
i)
Required numbers PC hook up cable for direct communication, one for each type of
relay.
ii)
Graphical configuration tool having all the functions used in the relay and sufficient
numbers different logic gates in the inbuilt library (software)
iii)
Basic application licensed software for setting change, service value monitoring etc.,
one each for every substation where numerical relays shall have to be provided.
iv)
Program for disturbance record collection and evaluation of those records.
v)
Any additional software if required for remote communication and for other facilities
available in the relay.
All the above tools/software should be WINDOWS XP/WINDOWS 7 operating system
compatible.

k)

The relay shall have inbuilt auto reclosure, disturbance recorder, fault locator, event logger
facility and additional features shall also be indicated over and above the features already
specified.

l)

Relay should be blocked in case of momentary dropping off of PT switching Relays to avoid
maloperation, if there be any. The VTF protection should be incorporated.

m)

The numerical distance relay should have in built directional sensitive earth fault element for
high resistance fault.

n)

The relay shall have suitable number of potential free contacts for carrier aided tripping, auto
reclosing, event logger, disturbance recorder and data acquisition system.

o)

The relay shall have a continuous current rating of two times of rated current, the voltage
shall be capable of operation at 1.2 times rated voltage. The relay shall also be capable of
carrying a high short time current without damage for a period of 1sec.

WBSETCL / TECH SPEC / Rev.-1

Page 30 of 104

Control & Relay Panel

p)

The relay shall have at least 15nos of individually site selectable Binary Inputs and 20nos
Binary Outputs (rating of Binary Input shall be 240V DC but they should not pick up at less
than 150V). Latching option for B/O shall have to be provided. Output contact of the
protective relay should operate single phase trip relay which will have sufficient contact to
give trip command to main breaker & TBC breaker & for LBB protection initiation and other
purpose.

16.08.01 AUTO-RECLOSE RELAY:

a)

b)
c)
d)
e)
f)
g)

h)

The scheme shall be compatible with the distance relaying scheme. It shall be suitable for
single shot, single and/or three phase auto-reclosing feature. The bidder shall coordinate the
auto-reclose relaying scheme with that of the circuit breaker so as to ensure satisfactory and
reliable operation of the auto reclosing scheme.
The auto reclose relays shall have independently adjustable dead timers for single phase and
three phase reclosures and an adjustable reclaim timer.
It shall also be possible to lock out the auto-reclosing scheme relays when the carrier
protection associated with distance protection scheme is out of service or faulty.
It shall have auto-reclose mode selection facilities as required.
It shall have facilities for selecting check synchronising or dead line charging feature. It shall
be possible at anytime to change the required feature as required.
It shall be built-in with the main distance relay.
The autoreclose relay along with necessary check synchronising or dead line charging
facilities and other associated features shall be in built in the Main-1 & Main-2 protection.
Either one shall be activated during operation and the other shall be kept as stand by. The
two inbuilt autoreclose relays should be well coordinated so that autoreclose command/
definite trip command etc may be initiated from either of the two units at the discretion of
WBSETCL personnel. The autoreclose element of the distance relay shall also be suitable for
triggering from other external protections.
In One and Half breaker system, while reclosing the Main breaker & Tie breaker for the Line
bay, a priority shall be assigned. The Main breaker shall be allowed to reclose first and only
after its successful recloser, the Tie breaker shall be allowed to reclose. If the fault persists
after reclosing of the Main breaker, reclosing of the Tie breaker is blocked.

16.08.02 FAULT LOCATOR:

a)
b)
c)
d)
e)
f)
g)

h)
i)
j)

The distance to fault locator shall be provided for all 400KV, 220KV and 132KV lines. It shall
be: Microprocessor based type.
be "on-line" type
be suitable for breaker operating time.
have built in display unit.
the display shall be directly in kilometers without requiring any further calculations.
have an accuracy of 3% of the line length for which the fault locator is installed or better
for all type of faults and fault levels.
the above accuracy should not be impaired under the following conditions:
i)
presence of remote end in feed.
ii)
predominant d.c. component in fault current.
iii)
high fault arc resistance.
iv)
severe CVT transients.
have facility for remote data transmission.
shall be built-in distance relay with facility for triggering from
external
protection.
shall have built in mutual compensation facility for using in double circuit lines and this
parallel line compensation shall not be used for protection purpose.

WBSETCL / TECH SPEC / Rev.-1

Page 31 of 104

Control & Relay Panel

16.08.03 DISTURBANCE RECORDER:

[The DR should be IEC61850 compliant having rear port compatible to IEC
61850 protocol.]
a)

b)

c)
d)

e)
f)
g)
h)

i)

Disturbance Recorder shall be used for 400KV, 220KV and 132KV system to record the
graphic forms of instantaneous/ rms values of voltages and currents, in all phases, open delta
voltage and neutral current, open or closed position of relay/ breaker contacts just prior to,
during and immediately after a system disturbance to provide information necessary to
ascertain the causes of disturbance and performance of relays, breakers etc. The system shall
start only on the occurrence of a system abnormality.
The disturbance recorder shall be inbuilt function of numerical distance/ differential relay. The
channels and trigger sources shall be user configurable. Program for disturbance records and
event logger collection and evaluation of those records shall be provided. Also the software
shall be capable of carrying out Fourier /harmonic analysis of the current and voltage
waveform. Disturbance shall also be available in COMTRADE format.
Number of Channels required for each feeder bay :
i)
Analog channel: 8 nos.
ii)
Digital channel: 24 nos.
The relay shall have the disturbance recording function with at least 8nos analog channels
and 24nos binary channels having total recording memory of at least 15secs divided in to 8
records and recording bandwidth may please be indicated. It should have on line pre and
post fault disturbance recording facility.
The disturbance recorder shall be suitable for working with 220V DC available at the Substation.
Each Relay & Disturbance Recorder shall have the facility to synchronise the internal clock
with GPS based time synchronising equipment directly through its own IRIGB port.
The accuracy of the internal clock shall be indicated by the bidder. The drift is limited to
0.5sec per day, if allowed to run without synchronisation. The recorder shall give
annunciation in case of absence of synchronising pulse within a specified time.
Substation where time synchronisation equipment is not available, time generator of any one
of the disturbance recorder can be taken as master and the time generator of other
disturbance recorder and event logger in the substation shall be synchronized to follow the
master.
The recorder shall have facility for automatic uploading of, remote data transmission. Scan
rate of D R shall be at least 1KHZ per channel or better. Facility for triggering of disturbance
recorder from external protection shall also be provided. Acquisition units shall acquire the
fault data for the prefault and post fault period and can be transferred on demand to
connected PC.

16.08.04 EVENT LOGGER:

a)
The event logger shall be in built feature of numerical distance/ differential relay with external
triggering facility
b)
The event logger shall record the state of switchyard equipment, relays and change of alarm,
change of setting, password etc.
c)
All recorded/stored events shall be date and time tagged followed by a message describing
the points which have been operated.
d)
Number of time tagged events in the event list should be sufficient enough to record/store all
possible sorts of events of the switchyard, equipments, relays etc.
e)
The printout of events shall contain at least the station & feeder identification, date and time
(in hour, minute, second and millisecond), event number and event description. The event list
and its print out may be available from S/S; PC and its printer to be supplied by the bidder for
a complete 400KV & 220KV S/Stn. The timing of each event shall be as per GPS based time
synchronising equipment to be supplied by the bidder, wherever applicable & mentioned in
the schedule..
All the necessary software for the event logger function and download the event list shall be
within the scope of the bid.

WBSETCL / TECH SPEC / Rev.-1

Page 32 of 104

Control & Relay Panel

16.09 NUMERICAL TYPE LINE DIFFERENTIAL PROTECTION RELAY:

[The relay should be IEC61850 compliant having rear port compatible to IEC
61850 protocol.]
The relay shall be of numerical type, IEC 61850 compliant and shall:i)
ii)
iii)
iv)
v)

vi)
vii)
viii)
ix)
x)
xi)
xii)
xiii)
xiv)
xv)

have phase segregated line differential protection.

have high immunity to electrical & electromagnetic interference.
have DR with 8nos analog channel & 16 nos binary channel.
generate GOOSE message as per IEC 61850 standards for interlocking and also to
ensure interoperability with third party relays.
be provided with necessary user friendly configuration tools to configure the relays
and shall be compatible with SCL/SCD files generated by a third party system.
GOOSE signals shall be freely configurable for any kind of signals using graphic
tool/user friendly software. There shall be a facility to have IEC 61850 protocol inbuilt
without use of any external converter.
have the facility of setting parameter access restriction.
have self supervision with fault diagnostics.
be provided with necessary WINDOWS XP/WINDOWS 7 based support software for
setting parameterisation, up & downloading data etc.
have backup O/C & E/F protection having DT/IDMT characteristics.
have channel communication with continuous supervision facility and the facility for
switching to backup protection mode in the event of communication channel failure.
have cold start switching facility at every end.
have phase segregated measurement and tripping facility.
have a high set differential trip setting with tripping time of maximum 15ms.
have a normal line differential trip time of maximum 35ms at 5 times of set value.
provide high stability during external faults.

16.10 TIME SYNCHRONISATION EQUIPMENT:

a)

b)
c)
d)
e)
f)
g)

The time synchronisation equipment shall receive the coordinated Universal Time (UTC)
transmitted through Geo Positioning Satellite system(GPS) and synchronise equipments to
Indian Standard time in a substation. It will also synchronise the substation PC through
necessary software to be supplied by the bidder.
Time synchronising equipment shall include antenna, all special cable and processing
equipments.
It shall be compatible for synchronisation of event loggers, disturbance recorder and SCADA
at a substation.
Equipment shall operate upto the ambient temperature of 50C and 100% humidity.
Equipment shall meet the requirement of IEC 60255 for storage and operation.
Equipment shall have real time display in hour, minute, sec (24 hr. mode)and have a separate
time display unit to be mounted on the top of the control panels or any suitable location
having display size of approximately 100mm height.
Equipment offered shall have six output ports .Various combinations of output ports shall be
selected by the customers, during detailed engineering from the following:
i)
Voltage signal: Normally 0 5 V with 50ms minimum pulse duration. In case any
other voltage signal required it shall be decided during detailed engineering.
ii)
Potential free contact (minm. pulse duration of 50ms).
iii)
IRIG-B
iv)
RS232C

WBSETCL / TECH SPEC / Rev.-1

Page 33 of 104

Control & Relay Panel

h)
i)
j)
k)
l)
m)

The synchronisation equipment shall have 2micro second accuracy. Equipment shall give real
time corresponding IST (taking into consideration all factors like voltage and temperature
variation, propagation and processing delays etc.).
The output signal of each port shall be programmable at site for either one hour, half hour,
minute or second pulse, as per our requirement.
The equipment shall have a periodic time correction facility of one second periodicity.
The equipment shall be suitable to operate from 220V DC 10% as available at the
substation.
The system shall be able to track the satellites to ensure no interruption of synchronisation
signal.
Time synchronization equipment consisting of :
i)
GPS antenna,
ii)
GPS receiver with detail of output & ports,
iii)
Requisite quantity of interconnecting cable with matching connector,
iv)
Master clock with display unit, power supply unit,
v)
Battery charger if required, time synchronization panel etc.
vi)
Necessary converter arrangement for deriving Power supply DC voltage from 220V
DC supply from our substation battery.
vii)
Synchronisation panel etc.
viii) Other particulars if any.

16.11 TRANSFORMER DIFFERENTIAL RELAY:

[The relay should be IEC61850 compliant having rear port compatible to IEC
61850 protocol.]
a)
b)
c)
d)
e)
f)

g)
h)
i)
j)
k)
l)

The protection shall be provided at the HV side panel of the transformers to be protected. It
shall be numerical type adjustable/variable percentage biased differential relay.
Necessary softwares, cables, connectors and other accessories as required in compatible with
Sub-station PC shall be provided by the Tenderer as described under clause 16.07 above.
The relay shall be very fast in operation with an operating time less than 30millisec at 5 times
setting.
The relays shall be inherently stable for external through fault conditions without affecting
the speed of operation for internal faults.
The relay shall have a built in facility of ratio and phase angle correction.
The relay shall be provided with 2nd harmonic restraint (having site selectable setting
facilities of 10% to 40% of I2/I1) or any other inrush proof feature to prevent operation due
to magnetising in rush current when the transformer is charged either from HV or LV side.
But this shall not affect the speed of operation for internal fault.
It shall be provided with 5th harmonic restraint features (having site selectable setting
facilities of 10% to 40% of I 5th/Ifund) to prevent operation due to possible over excitation of
the transformer. This shall also not affect the speed of operation for internal fault.
It shall have three instantaneous high set over current units for clearing heavy internal faults.
The relay shall have adjustable bias setting range 20% to 50% and adjustable operating
setting range of 10% to 50% at zero bias.
The relay shall be with 3-bias winding for 400/220/33KV and 220/132/33KV transformers and
2-bias winding for 220/33KV, 132/33KV and 10MVA and above 33/11KV transformers.
The relay shall be such that there will not be any necessity of changing the setting of the
relay whenever the transformer taps are changed.
The relay shall be provided with GPS based time synchronized disturbance recorder with date
and time tagged records with the facility of triggering from other external protective relays of
the transformer. The disturbance recorder shall be capable of recording graphic form of
values of currents each phase, differential currents of each phase etc. and store them in the

WBSETCL / TECH SPEC / Rev.-1

Page 34 of 104

Control & Relay Panel

m)

n)
o)

memory which can be downloaded both from local and remote end PC. Memory size and
number of disturbances stored in the relay shall be clearly indicated in the offer.
The in-built disturbance recorder shall have the facility to record the following external digital
signal apart from the digital signals pertaining to differential relay.
i)
REF protection operated
ii)
Over flux relay operated
iii)
Dir/ Non-Dir O/C relay operated
iv)
HV breaker status(Main & Tie)
v)
LV breaker status
vi)
Buchholz/OLTC Buchholz alarm/trip
vii)
WTI/OTI/PRD alarm/trip of transformer
The relay shall have disturbance recording function with at least 9 nos analog channels and
10nos digital channels having total recording memory of 5 secs divided in to 5 records and
recording bandwidth may please be indicated.
The relay shall have at least 5nos of individually site selectable Binary Inputs and 8nos Binary
Outputs (rating of B/I shall be 240V DC but they should not pick up at less than 150V).
Latching option for B/O shall have to be provided. Output contact of protective relay should
operate trip relay which will have sufficient contact to give trip command to main breaker,
TBC breaker & for LBB protection initiation and other purposes.
Necessary hardware and software for downloading the data captured by disturbance recorder
to the personal computer available in the substation shall be included in the scope.

16.12 RESTRICTED EARTH FAULT PROTECTION:

The above protection shall be provided for 220/132/33KV auto-transformers, 220/33KV
transformer & 132/33KV transformers both at HV and LV side and also 33/11KV transformers
at HV and LV side.
The Relay shall be:
a)
b)
c)
d)
e)
f)
g)

stand-alone type
single pole type.
current/voltage operated high impedance type with a suitable setting to cover the maximum
portion of transformer winding. Necessary calculation to prove the above winding coverage
shall be furnished along with the tender.
tuned to the system frequency.
have suitable nonlinear resistor to limit the peak voltage without detriment to the scheme.
operating time shall be less than 20 ms.
have suitable stabilizing resistor to prevent maloperation during external faults if necessary.

16.13 CIRCULATING CURRENT PROTECTION FOR 400/220/33KV AUTO TRANSFORMER:

The above protection shall be provided for 400/220/33KV auto-transformers at the HV side
protection panel and for the 400 KV bus reactor to act as differential protection .The
protection shall be responsive for both phase and earth fault of the transformer and reactor
winding. The relay shall be
a)
stand-alone type
b)
triple pole type .
c)
voltage operated high impedance type with a suitable setting to cover the maximum portion
of the transformer winding. Necessary calculation to prove the above winding coverage shall
be furnished along with the tender.
d)
tuned to the system frequency.
e)
have suitable nonlinear resistor to limit the pick voltage without detriment to the scheme .
f)
operating time shall be less than 20msec .

WBSETCL / TECH SPEC / Rev.-1

Page 35 of 104

Control & Relay Panel

16.14.01 OVER FLUXING PROTECTION:

a)
The HV side of 400/220/33KV & 220/132/33KV Auto-Transformer and 220/33KV Transformer
shall be provided with stand alone numerical type over fluxing relay.
b)
The relay shall operate on the principle voltage to frequency ratio.
c)
It shall have characteristics compatible with transformer over fluxing withstand capability.
d)
Input shall be 110V, 50Hz, Auxiliary Volt 220V DC 20%
e)
Over Flux relay characteristics should be suitable for: i. 110% continuous
ii. 125% for 1min.
iii. 140% for 5sec.
f)
Alarm : - Settable between 100% - 130% with Definite Time delay, settable from 3 30 sec.
g)
Drop Off/ Pick Up ratio should not be less than 98%.
h)
BI 3nos Min., BO 5nos Min., Watchdog Contact.

16.14.02 OVER LOAD PROTECTION:

The protection shall be used for 400/220/33KV & 220/132/33KV Auto-transformer and shall
be located at HV side protection panel of respective transformer.
The relay shall be a)
definite time, single pole type.
b)
have a variable and continuously adjustable current setting range of 50% to 200% of
rated current and variable time setting 2.5 to 25 sec. of the timer unit.
c)
included hand reset flag indicator.
d)
the relay shall provide alarm only.
e)
have a drop off/pick up ratio greater than 95%.
f)
May be in built feature of numerical differential relay
16.15 OVER VOLTAGE PROTECTION:
The relay shall be stand-alone type & connected to Line CVT. It will be used for 400KV feeder
protection and shall
a)
monitor all three phases.
b)
be connected between Phase to Phase in Delta configuration.
c)
have two stages .
d)
have an adjustable setting range of 100 - 170% of rated voltage with an adjustable time
delay range of 1 to 60secs for the first stage .
e)
have an adjustable setting range of 100 170% of rated voltage with a delay of 100
200msec for the second stage .
f)
have power frequency filters.
g)
have a drop off to pickup ratio greater than 99%.
h)
provide separate output contact for each Phase and stage for breaker trip relays, event
logger and other scheme requirement.
16.16 NUMERICAL DIRECTIONAL/NON-DIRECTIONAL OVER CURRENT & EARTH FAULT
PROTECTION:

a)
b)

This relay will be used as back up protection of 400/220/33KV & 220/132/33KV Transformer,
HV side of 220/33KV & 132/33kV Transformer and back up to distance relays for 220KV and
132KV system and shall have follow propertiesMinimum two characteristics, one IDMT of 3sec and the other one of definite time
characteristic with instantaneous high set and the same should be site selectable.
Wide range of time and current setting in very small steps without sacrificing the relay
characteristics.

WBSETCL / TECH SPEC / Rev.-1

Page 36 of 104

Control & Relay Panel

c)
d)
e)
f)
g)
h)
i)
j)
k)
l)
m)
n)
o)
p)

q)

r)
s)

t)

Any of the out puts including trip shall be latched and reset of the outputs shall be possible
from a logic input and the front panel operator interface.
Continuous self supervision along with self diagnostic feature for faults within the relay and
the relay should have potential free change over contact for annunciation in the event of
internal failure.
DC auxiliary voltage 220V20%, 110v. 20%
Rated current 1A.
Frequency 50Hz.
Digital input voltage range shall be identical to the DC voltage range.
Thermal withstand capability 100A for 1Sec/ 4A continuous.
Output contacts having sufficient current rating to directly energize trip coil of circuit breaker.
LED indication facility for visual annunciation of different type of faults including phase
identification. Fault indication should be displayed in the stand-by screen.
Individually site selectable both binary Output & Input and latching option for binary Output.
Relay should show fault current with time stamping.
The relay shall have more than one selectable setting group.
The setting group can be changed by binary inputs.
The relay shall have a non volatile memory for i)
Event recorder - shall have the facility of recording up to 75 events with time
stamping.
ii)
Setting values.
iii)
Disturbance recorder data - Recorded data of 5 last events with time stamp. The
disturbance recording function is triggered either by any of programmed threshold or
by an external input. All logic and analog information can be transferred using
communication port to an external data analyzer. Current waveforms shall be
captured.
Fault records - At least five nos fault records shall be available with the following indications:
i)
Fault indication.
ii)
Current values.
iii)
Tripping time.
Measurement -Instantaneous three phase current values and residual current value. All the
measured and derived values can be displayed on the front panel LCD.
No of output contact required 8 nos
No. of digital input required 6 nos
All numerical relays shall have one front port for direct access with proprietary protocol and
one rear port with IEC 61850 protocol.
The numerical directional shall have built in feature for derivation of zero sequence voltage
internally. If separate IVT is required for derivation of zero sequence voltage for directional
earth fault element, the ratio of IVT will be 110/110V with burden of 5VA and class 3P. The
MTA of numerical directional relay shall be 45lag for earth fault and 45lead for over current.
Any extra feature like time synchronization, LAN compatibility with other numerical relays
shall be mentioned specifically.

16.17 AUXILIARY RELAY

PROTECTIONS:
DC voltage operated
indicator and sufficient
and supervision against
of relays shall be as per

WBSETCL / TECH SPEC / Rev.-1

FOR

TRANSFORMER

&

REACTOR

INTERNAL

TROUBLE

auxiliary relays provided with mechanically operated hand reset

number of hand reset contacts shall be provided for protection
transformer internal troubles/faults. Number of element and number
requirement of individual transformers and reactor.

Page 37 of 104

Control & Relay Panel

16.18 MASTER TRIP RELAY:

Master trip relay shall be provided to cause tripping of all the associated breakers. The
operating time of master trip relay should be less than 15ms. This relay shall also be provided
in other bays for closing lock out of breaker. Master trip relay coil supervision shall be
provided. The relay shall be provided with electrical reset as well as hand reset arrangement.

16.19 LOCAL BREAKER BACK UP PROTECTION:

The above protection shall be stand alone type or built in function of bus bar protection
scheme and shall be provided for 400KV & 220KV bays. The protection scheme shall be so
designed that if any circuit breaker fails to trip in the event of a fault, then after a short time
delay all the adjacent circuit breakers connected in the same bus will be tripped. The circuit
breaker failure shall also block auto-reclosing scheme. The scheme shall be complete with
timer and auxiliary relays as necessary including remote end tripping facility. The relay shall
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)

k)

l)

be triple pole type.

have a operating time less than 15millisecond.
have an resetting time less than 15millisecond.
have three over current element with facility for phase wise initiation.
have a current setting range 20 to 320% of rated current for over current.
have a continuous thermal withstand of two times rated current irrespective of the setting.
have timer suitable for sub-station D.C. with a continuously adjustable setting range of 0.1 to
1sec.
be of solid state/ numerical type.
trip and lock out all the local breakers. Simultaneously direct trip signal shall be sent to
remote end circuit breakers (through both channels in case of 400KV system) and lock out its
auto-reclosing feature.
have necessary auxiliary relays to make a comprehensive scheme.

Trip all the breakers on the particular bus in a One & Half breaker system, when any
bus breaker fails to trip in faulty condition. However, when a Tie Breaker fails to
open, the LBB relay shall trip the adjacent bus breakers as well as both the breakers
at the remote end of the bays.
LBB for Tie breaker shall be standalone type.

16.20 TRIP CIRCUIT SUPERVISION RELAYS :

a)
DC supply to each trip coil of the circuit breakers shall be supervised with an independent trip
circuit supervision relay. These relays shall be mounted in the relay panel associated with the
circuit breaker.
b)
These relays shall monitor the whole of the trip circuit whether the breaker is in open or
closed and give an alarm for the (i) loss of D.C. supply or (ii) for faults in the trip coil or for
faults in the trip circuit leads or for faults in the breaker auxiliary contacts or faults in the
supervisory relay itself. The relay shall have a delay in drop off at least 200ms to avoid a false
alarm during a normal tripping operation.
16.21.01 NUMERICAL BUS BAR PROTECTION - For 400KV substation only
[The relay should be IEC61850 compliant having rear port compatible to IEC
61850 protocol.]
For 400KV bus bar protection two redundant full scheme of Bus Bar protection incorporating
individual buses and transfer bus is to be provided. The tripping logic should be AND Logic in
case when both the bus bar protection relay is available. In case of non availability of one bus
WBSETCL / TECH SPEC / Rev.-1

Page 38 of 104

Control & Relay Panel

bar relay, the tripping logic will be based on available relay. The Central Processing Unit of
bus bar protection & Bay Unit of numerical bus bar protection scheme shall be housed in a
separate set of simplex type panel along with equipment/relays.
One Bus bar protection scheme shall be provided for each main and transfer bus for 220KV
and 132 KV voltage levels but for 132KV substations having 1Main + 1 Transfer bus
arrangement, no bus bar protection scheme is required.
a) Bus Bar protection scheme shall: i)
have maximum operating time up to trip impulse to trip relay for all types of faults of
25 milli seconds at 5 times setting value.
ii)
operate selectively for each bus bar
iii)
give hundred percent security up to 50KA for fault level for 400KV and 220KV and
31.5 KA for 132 KV
iv)
incorporate continuous supervision for CT secondary against any possible open circuit
and if it occurs, shall render the relevant zone of protection inoperative and initiate an
alarm
v)
not give false operation during normal load flow in bus bars.
vi)
incorporate clear zone indication.
vii)
be of phase segregated and triple pole type
viii) provide independent zones of protection (including transfer bus if any). If the bus
section is provided then each side of bus section shall have separate set of bus bar
protection schemes
ix)
include individual high speed hand reset tripping relays for each feeder
x)
be transient free in operation
xi)
include continuous D.C. supplies supervision.
xii)
not cause tripping for the differential current below the load current of
heaviest loaded feeder. Bidder shall submit application check for the same.
xiii) shall include necessary C.T. switching relays wherever C.T. switching is involved and
have 'CT' selection incomplete alarm
xiv) include protection 'IN/OUT' switch for each zone
xv) include trip relays, CT switching relays (if applicable), auxiliary CTs (if applicable) as
well as additional power supply modules, input modules etc. as may be required to
provide a Bus-bar protection scheme for the complete bus arrangement i.e. for all the
bay or breakers under this specification as well as for the future bays as per the
Single line diagram for new substations. However for extension of bus bar protection
scheme (if specified in BPS) in existing substations, scope shall be limited to the bay
or breakers covered under this specification. Suitable panels to mount these are also
included in the scope of the work.
b)
c)

Built-in Local Breaker Backup protection feature as a part of bus bar protection scheme shall
also be acceptable.
At existing substations, Bus-bar protection scheme with independent zones for each bus, will
be available. All necessary co-ordination for 'AC' and 'DC' interconnections between existing
schemes (Panels) and the bays proposed under the scope of this contract shall be fully
covered by the bidder. Any auxiliary relay, trip relay, flag relay and multi tap auxiliary CTs (in
case of biased differential protection) required to facilitate the operation of the bays covered
under this contract shall be fully covered in the scope of the bidder.

16.21.02 BUS BAR PROTECTION For 220KV substation

a)

Bus bar protection scheme shall be provided for 220KV system where the sub-station layout
arrangement is with 3-bus system (Main 1, Main 2 & Transfer Bus) or two bus system with
Main bus with bus section breaker & Transfer bus. Bus bar protection for two main bus

WBSETCL / TECH SPEC / Rev.-1

Page 39 of 104

Control & Relay Panel

b)
c)

system shall also be provided wherever applicable. Bus bar protection for two main bus with
one & Half breaker system shall also be provided wherever applicable.
Bus bar protection relaying scheme shall be provided in a separate simplex type panel with all
bus differential relays, CT switching relays and trip relays etc. as required considering future
bays.
Bus bar protection scheme shall be Numerical type and it shall have maximum
operating time for all types of fault at five times set value is 25ms up to trip impulse to trip
relay.
Bus Bar protection scheme shall: i)
operate selectively for each bus bar
ii)
give hundred percent security up to 40 KA fault level for 400KV and 220KV and 31.5
KA for 132 KV
iii)
incorporate continuous supervision for CT secondary against any possible open circuit
and if it occurs, shall render the relevant zone of protection inoperative and initiate an
alarm
iv)
not give false operation during normal load flow in bus bars.
v)
incorporate clear zone indication.
vi)
be of phase segregated and triple pole type
vii)
provide independent zones of protection (including transfer bus if any). If the bus
section is provided then each side of bus section shall have separate set of bus bar
protection schemes
viii) include individual high speed hand reset tripping relays for each feeder
ix)
be transient free in operation
x)
include continuous D.C. supplies supervision.
xi)
not cause tripping for the differential current below the load current of
heaviest loaded feeder. Bidder shall submit application check for the same.
xii)
shall include necessary C.T. switching relays wherever C.T. switching is involved and
have 'CT' selection incomplete alarm
xiii) include protection 'IN/OUT' switch for each zone
xiv) include trip relays, CT switching relays (if applicable), auxiliary CTs (if applicable) as
well as additional power supply modules, input modules etc. as may be required to
provide a Bus-bar protection scheme for the complete bus arrangement i.e. for all the
bay or breakers under this specification as well as for the future bays as per the
Single line diagram for new substations. However for extension of bus bar protection
scheme (if specified in BPS) in existing substations, scope shall be limited to the bay
or breakers covered under this specification. Suitable panels to mount these are also
included in the scope of the work.
d) Built-in Local Breaker Backup protection feature as a part of bus bar protection scheme shall
also be acceptable.
e) At existing substations, Bus-bar protection scheme with independent zones for each bus, will
be available. All necessary co-ordination for 'AC' and 'DC' interconnections between existing
schemes (Panels) and the bays proposed under the scope of this contract shall be fully
covered by the bidder. Any auxiliary relay, trip relay, flag relay and multi tap auxiliary CTs (in
case of biased differential protection) required to facilitate the operation of the bays covered
under this contract shall be fully covered in the scope of the bidder.

16.22 TEE DIFFERENTIAL PROTECTION

Duplicated differential protection scheme namely Tee Differential protection shall be

provided for One and Half Breaker system. This scheme shall protect the circuit
between the Main breaker & the tie breaker. Two separate differential relays on
different hardware platform shall be used for Main I and Main II protection.

WBSETCL / TECH SPEC / Rev.-1

Page 40 of 104

Control & Relay Panel

16.23 STUB PROTECTION

Stub protection scheme shall be applicable for one and half breaker system. This
protection shall protect the part of one & half breaker system, not covered by
distance protection.
Stub protection scheme shall be: i)
active only when Line isolator is open & there is no voltage from CVT for
distance protection relay.
ii)
the inbuilt function of the main Numerical Protection relay.
iii) Able to sense the fault through a overcurrent sensing element & trip bus
breaker under fault condition.

16.24 CONFIGURATION AND MONITORING TOOLS FOR ALL NUMERICAL RELAYS:

The manufacturer/bidder has to provide configuration and monitoring tool for all type of
numerical relays used for a particular sub-station without any price implication.
a)
b)
c)
d)
e)

PC hook-up cable for direct communication in sufficient quantity for each substation.
Graphical configuration tool having all the functions used in the relay and sufficient nos. of
different logic gates in the in built library (software).
Basic application software for setting change, service value monitoring etc.
Programme for disturbance record collection and evaluation of those records.
Any additional software, if required, for remote communication and for other facilities
available in the relay.
All the above tools/software should be Windows XP/WINDOWS 7 Operating system
compatible.

17.00 PROTECTION PHILOSOPHY:

The bidder has to design the protection scheme for lines, transformers, Bus coupler, Bus
Transfer bay of 400KV, 220KV, 132KV and 33KV system as applicable depending upon the
substation layout arrangement and the schemes are to be submitted along with their offers
for acceptance of the same by WBSETCL. All the protective relays etc. of each bay shall be
mounted in the respective bay panel. Similarly for 400/220/33KV, 220/132KV and 132/33KV
transformer protection, relay of each system voltage shall be located in the respective panel.
However, the protection schemes shall be generally based on the requirement listed below:
17.01 400KV LINE PROTECTION:
The general concept is to have two parallel primary protections having equal reliability of
performance called Main 1 and Main 2 protection. Main 1 and Main 2 distance
protection relay shall be of different make.
a)
b)
c)
d)

The following protection scheme has been envisaged: Main 1 distance protection by microprocessor based numerical distance relaying scheme
with carrier aided distance protection scheme.
Main 2 distance protection by microprocessor based numerical distance relaying scheme but
of a different make with carrier aided distance protection scheme.
Auto reclosing, fault locator and disturbance recorder scheme.
Local breaker back up protection scheme.

WBSETCL / TECH SPEC / Rev.-1

Page 41 of 104

Control & Relay Panel

e)
f)
g)

Direct tripping command from remote end through carrier channel.

Line CVT operated two stage over voltage protection.
Main-1 & Main-2 PT juice either BVT/CVT is to be mentioned.

17.02 PROTECTION OF 315MVA, 400 / 220 / 33 KV AUTO TRANSFORMER PROTECTION:

Percentage biased differential protection (three winding).
a)
Circulating current protection responsive to both phase faults and earth faults.
b)
Directional IDMT polarised, three element over current with directional high set and single
element earth fault protection scheme with directional high set both at HV and MV side with
necessary PT fuse failure monitoring feature.
c)
Over load protection alarm on HV side.
d)
Transformer over flux protection on HV side & MV side.
e)
Flag relays for transformer mounted protection like buchholtz, winding temperature, oil
temperature, pressure relay device etc.
f)
Local breaker back up protection at HV side & MV side.
g)
Tertiary winding protection as recommended by transformer manufacturer.

17.03
a)
b)
c)
d)
e)

400KV BUS REACTOR PROTECTION:

Differential protection.
Restricted earth fault protection.
Back up single step distance protection.
Reactor internal trouble i.e., buchholz, winding temperature etc. protection.
Local breaker back up protection.

17.04 220KV AND 132 KV LINE PROTECTION:

a)
Carrier aided distance protection scheme numerical relay shall be offered. The auto-recloser,
disturbance recorder, fault locator, event logger etc. shall be built in with distance relay as
specified in Clause no.16.08.
b)
For 132kV Line, where the line length is less than 3km, Line Differential protection
scheme numerical relay is to be considered.
c)
For 132KV cable line also, Line Differential protection scheme numerical relay is to be
considered.
d)
Back up protection with voltage polarised, IDMT, directional Over current and earth fault
relaying scheme with necessary PT fuse failure monitoring scheme for both the above cases.
e)
Local breaker back up protection.
f)
Fault locator and disturbance recorder in 220KV & 132KV system.

17.05
a)
b)
c)

d)
e)
f)
g)

220/132/33KV AUTO-TRANSFORMER PROTECTION:

Percentage biased differential protection (three winding).
Restricted earth fault protection.
Back-up directional voltage polarised, three element IDMT over current with directional
high set instantaneous element and one earth fault protection with directional high set
instantaneous element both at HV side and MV side with necessary P.T. fuse failure
monitoring scheme.
Flag relays for transformer mounted protections like Buchholz, winding temperature, oil
temperature, pressure relief device etc.
Local breaker back up protection at HV side only.
Over flux protection and over load alarm at HV side.
Necessary protection with neutral displacement relay for tertiary winding.

WBSETCL / TECH SPEC / Rev.-1

Page 42 of 104

Control & Relay Panel

17.06
a)
b)
c)
d)
e)

132/33 KV STAR-DELTA TRANSFORMER PROTECTION:

The control and protection shall cover both HV&LV side breakers.
Percentage biased differential protection (Two winding).
Restricted earth fault protection both at HV and LV side.
Back up non directional, IDMT three over current protection both at HV and LV side.
Earthing transformer neutral C.T. operated definite time earth fault protection. The earthing
transformers shall be connected at 33KV bus outside the transformer differential zone.
Provision for selection of three numbers Earthing Transformers with three sections of 33KV
Bus shall be achieved as per the furnished diagram.
Earthing Transformers
Power Transformers

f)

g)

17.07
a)
b)
c)

For the above, selection of necessary tripping scheme shall be achieved with the help of
Selector Switch, as per scheme requirement. This earth fault relay will trip HV
breaker/breakers after a preset time delay. The switches shall be having sufficient number
of contacts. The trip relays shall have sufficient number of contacts for extending the trip
pulse to other 33KV feeders connected with generating stations.
Flag relays for transformer mounted protections like Buchholz, Winding temperature, Oil
temperature, Pressure relief device etc. shall be provided. Internal trouble protection auxiliary
relays for alarm and trip signal to LV breakers for earthing transformer to trip 33KV breaker
shall have sufficient number of contacts for extending the trip pulse to other 33KV feeders
connected with generating stations and only alarm signal for station service transformers
shall also be provided.
Trip transfer scheme for both HV&LV side shall be provided with two separate trip transfer
switch.

400KV & 220KV BUS COUPLER PROTECTION:

Over Current & Earth Fault Protection (for 3 bus system).
Bus bar protection.
Local breaker back up protection.

17.08 400KV & 220KV TRANSFER BUS BAY PROTECTION:

The breaker shall be used for transfer of any circuit through transfer bus in case of necessity.
During the period of transfer the line side CT operated protection of transferred circuit will
trip the transfer bus breaker in place of respective bay circuit breaker through trip transfer
switch. Normally, the protection scheme provided in transfer bus bay excepting the LBB
protection shall be kept inoperative with the help of protection IN/ OUT selector switch.
However, its own protection shall be used when there is trouble in the protection system of
transferred circuit.
The protection scheme of transfer bus bay shall be as follows: a)
Single distance protection scheme for transferred feeder protection with protection IN/ OUT
switch. Numerical type shall be quoted as per feeder protection.
b)
Local breaker back up protection.

WBSETCL / TECH SPEC / Rev.-1

Page 43 of 104

Control & Relay Panel

17.09 132KV TRANSFER BUS BAY PROTECTION:

The breaker shall be used for transfer of any circuit through transfer bus in case of necessity.
During the period of transfer, the protective relays of individual circuits operated from line
side CTs will trip the Transfer bus breaker in place of respective bay circuit breaker through
trip transfer circuit. The protection scheme provided in the transfer bus bay shall be kept
inoperative with the help of a 3-position protection selector switch having selection for Feeder
132/33KV transformer and off position. The contacts of the switch shall be make before
break type. However, its own protection shall be used when there is trouble in the protection
system of transferred circuit.
The protection scheme for transfer bus bay shall be as follows: a)

b)
c)

Distance protection scheme for feeder bay protection shall be with protection selector switch.
Numerical relay shall be quoted as per feeder protection. The transfer bus numerical distance
relay should be identical type of those relays used in the feeder protection for easy
replacement of the same in future if required.
Back up protection of feeder with voltage polarised, directional, IDMT, two over current and
one earth fault protection scheme with protection selector switch and VT supply supervision
scheme.
Non-directional, IDMT, three over current and one earth fault protection for 132/33 KV
transformer protection. (The relay plug setting should be judged properly for protecting rated
to 100% loading)

17.10 33KV FEEDER PROTECTION:

a)
Non-directional, IDMT, three over current protection with high set instantaneous unit.
b)
Non-directional, definite time sensitive earth fault protection.

17.11 33/11KV TRANSFORMER PROTECTION (DELTA-STAR):

a)
Non-directional, IDMT, three over current protection with high set instantaneous unit at HV
side.
b)
Restricted Earth fault protection for HV & LV.
c)
Transformer internal trouble protection e.g. Buchholz, winding temperature etc.
d)
Under frequency relay operated CB tripping scheme as stated under 17.12 (c).
e)
Percentage bias differential protection (Two winding) for 10MVA and above, 33/11KV
transformers.

17.12 33KV TRANSFER BUS BAY PROTECTION:

The breaker shall be used for transfer of any circuit excepting the 33KV Shunt Capacitor bay
through transfer bus in case of necessity. During the period of transfer, the line side C.T.
operated protection of individual circuit will trip the transfer bus bay circuit breaker in place of
respective bay circuit breaker through trip transfer circuit. Therefore, the protection scheme
provided in the bus transfer bay shall be kept inoperative with the help of a 3-position
protection Selector switch having selection for feeder, transformer and OFF position. The
switch shall have make before break contacts. However, its own protection shall be used
when there is trouble in the protection system of transferred circuit.
a)
b)

The protection scheme for the transfer bus bay shall be Non-directional, IDMT, three over current protection with high set instantaneous unit with
protection selector switch.
Non-directional, definite time earth fault protection with protection selector switch.

WBSETCL / TECH SPEC / Rev.-1

Page 44 of 104

Control & Relay Panel

c)

One common under frequency relay of setting range 45 to 55 HZ in adjustable steps and with
timer relay of 0 to 20 second adjustable setting range with sufficient number of contacts shall
be provided from tripping of all 33 KV outgoing breakers.

17.13 33KV SIDE OF 220/132/33KV TRANSFORMER FOR TERTIARY LOADING:

a)
Non-directional, IDMT, three over current protection with high set instantaneous unit at HV
side.
b)
Neutral displacement relaying scheme through open delta connection.

17.14 33kV SHUNT CAPACITOR BANK PROTECTION:

a)
Non directional IDMTL Overcurrent & Earth Fault protection relay.
b)
Unbalance Protection scheme relays for double star connected capacitor bank with floating
neutral. The relay used shall detect two current levels, one for alarm & another for tripping.
It shall be able to provide alarm in the event of failure of one or two units before tripping.
c)
Over voltage & Under voltage protective relay with inverse time characteristics.
d)
CB closing shall have interlock with a timer as per Capacitor discharge time so that the CB
cannot be closed within the capacitor discharging time.

17.15 BUS CONFIGURATION FOR 400KV, 220KV, 132KV AND 33KV SYSTEM OF
DIFFERENT S/S.:
a)
b)
c)
d)

Bus configuration for various voltage class shall be as follows, unless otherwise mentioned:
400KV switchyard of all the sub-stations shall be of One & a Half Breaker system or two Main
bus and one Transfer Bus system.
220KV switchyard of all the sub-stations shall be with two main Bus and one transfer Bus.
132KV switchyard of all the sub-station shall be either with one Main Bus with/without bus
section breaker and one transfer Bus or two Main bus and one Transfer Bus.
33KV switchyard of all the sub-station shall be with one main Bus and one Transfer. But 33KV
shunt capacitor shall be connected at Main Bus only where applicable.

17.16 Approximate route length of different circuits of 400KV, 220KV and 132KV system controlled
by different feeder bays are as stated in GCC under Scope of work.

18.00 SYNCHRONISATION:
One synchronising panel mounted on a movable trolley shall be provided for use in 400KV
system and another one for both in 220KV & 132KV system, wherever mentioned in the
schedule. For 400KV synchronization shall be achieved by comparing between phase to phase
voltage and for 220KV & 132KV, synchronization shall be achieved by comparing between
phase to neutral voltage.
a)

The trolley shall be equipped with

Two voltmeters for running & incoming, each having scale suitable for 400KV, 220KV &
132KV system and also suitable for operation with CVT/ EMVT secondary voltage of 110v
phase to phase.

WBSETCL / TECH SPEC / Rev.-1

Page 45 of 104

Control & Relay Panel

b)
c)
d)
e)
f)
g)
h)
i)
j)
k)

Two frequency meters each having scale range 45 to 55Hz, indicating type.
One suitable synchroscope with cut off switch.
One suitable auxiliary voltage transformer for synchronising condition.
One synchronising bypass switch with necessary under voltage relaying scheme of running
system and incoming system to check inadvertent circuit breaker closing under synchronising
bypass condition.
One check synchronising relay with necessary auxiliary equipment which shall permit the
circuit breaker to close after checking the requirement of synchronising of incoming and
running supply.
One guard relay to prevent the closing attempt by means of synchronising check relay when
control switch is kept in close position long before the two systems are in synchronism.
Two synchronizing lamps of white colour.
One green indicating lamp to indicate check synchronism in limit.
One red indicating lamp to indicate check synchronism by pass.
Any other equipment required to render satisfactory operation of synchronism.

19.00 MANDATORY SPARES:

Shall be supplied as per schedule.

20.00 SCHEDULE OF EQUIPMENT OF DIFFERENT PANELS:

Though the Bidder has to design the Control Panel and Protection Schemes for Lines,
Transformers, Bus Coupler & Bus Transfer Bays of 400KV, 220KV, 132KV, 33KV System,
which are within the scope of the tender, as per the protection philosophy specified in the
specification under Cl. No. 17.00., the list of equipment is given below for general
guidance of the bidder. The actual requirement for different substations is to be assessed
by the bidder and to be quoted accordingly for successful operation of the control and
protection scheme. Same shall be finalized during detailed engineering and if any
additional equipment be found necessary for proper operation, match and
coordination with the existing panel, the same shall also be arranged by the
bidder without any extra price.

WBSETCL / TECH SPEC / Rev.-1

Page 46 of 104

Control & Relay Panel

20.01 (A) 220 KV DUPLEX TYPE CONTROL AND RELAY PANEL FOR THREE BUS (TWO
MAIN & ONE TRANSFER) SYSTEM:
Q u a n t I t y
Sl. No.

Particulars

Unit

Feeder

HT side of
220/132kV
& 220/33KV
Transformer

Bus
Coupler

Bus
Transfer

3
2
1
1

3
1
1

A. FRONT PANEL:
1.

Metering Device

a)
b)
c)
d)

Ammeter
Voltmeter
Watt meter with transducer
Varmeter with transducer

Nos
Nos
Nos
Nos

3
1
1

e)

Wiring for intelligent electronic

computer
compatible
energy
meter (0.2 class)
Test Terminal Block
Voltmeter Selector Switch
Frequency Meter
Control Device

Nos

3
1
1
(not reqd.
for
220/33KV
TR.)
1

Nos
Nos
Nos

1
-

1
-

2
2

Circuit Breaker Control Switch

discrepancy type with built-in
indicating lamp
Isolator Control Switch
Auto-reclose Selector Switch (if
necessary)
Trip Transfer Switch
Synchronising Selector Switch
2 position
Multipin Synchronising Socket
(with
dummy
plug
where
necessary)
Discrepancy Switch Steady Lamp
Cut-off Switch 2 position
Carrier Selector Switch
Bus Transfer Bay Protn. IN/OUT
Selector Switch. 2 position
Bus VT Selector Switch VTI / VT2
Indication

Nos

Nos
Nos

4
1

4
-

2
-

3
-

Nos
Nos

1
1

1
1

Set

Nos

Nos
Nos

1
-

Nos

Nos
Nos

1
4

f)
g)
h)
2.
a)

b)
c)
d)
e)
f)

g)
h)
i)
j)
3.
a)
b)

LED Position Indicator of Earth

Switch
LED Position Indicator of Isolator

WBSETCL / TECH SPEC / Rev.-1

Page 47 of 104

Control & Relay Panel

Q u a n t I t y
Sl. No.

Particulars

c)

Indicating lamp for incoming DC

fail/ANN. Bus DC fail and Bus PT
1&2 healthy
Push Button for Incoming DC
fail/ANN. Bus DC fail alarm accept
& test
Circuit breakerTrip circuit healthy
indicating lamp
Trip circuit healthy Check Push
Button
C.B.Spring charge indicating lamp
where necessary
Push Button for C.B. Spring
check, if required
Test PB for protn DC, Annun.DC,
incoming AC supervision etc
Indication for Distance Protn.
Carrier Signal recd., if required
Bus VT-1/VT-2 supply healthy
indicating lamp
Other Devices

d)

e)
f)
g)
h)
i)
j)
k)
4.
a)
b)
c)

Circuit Label
Section of Mimic Diagram
Internally mounted equipment
like
Heater
with
Switch,
Thermostat, Cubicle Illumination
Lamps, Power Socket, Switches,
Fuses, Link etc. as described in
the main specification
d)
One
Label
Indicating
Manufacturers
Name,
P.O.
Details, Drg. Ref. Nos. etc.
e)
Annunciation Windows as reqd,
with Lamps, Accept/Reset/Test
Push Button etc. and associated
Relays if the annunciator relay is
attached with the windows
f)
Common Bell, Hooter, Associated
relays etc. for Annunciation
Scheme
B. REAR PANEL:

WBSETCL / TECH SPEC / Rev.-1

Feeder

HT side of
220/132kV
& 220/33KV
Transformer

Bus
Coupler

Bus
Transfer

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos
Nos

1
-

Nos
Set

2
1

2
1

2
1

2
1

Set

Set

nos

24

32

24

24

Set

Unit

Page 48 of 104

Control & Relay Panel

Q u a n t I t y

Feeder

HT side of
220/132kV
& 220/33KV
Transformer

Bus
Coupler

Bus
Transfer

Nos

Nos

Set

Set

Set
Set

1
1

1
1

1
1

1
1

Set

Set

1 (3 O/C)

Sl. No.

Particulars

Unit

1.

CB Trip Circuit and master trip

relay coil (86 & 96) Supervision
Relay
Line CVT operated Under Voltage
Relay for line side earth switch
interlock
Breaker failure relaying scheme
complete with Aux. relay, timers
etc.
Bus VT supply selection relaying
scheme
for
metering
and
protection circuit complete in all
respect
Auxiliary
relays
for
C.B.
Closing/Tripping, if necessary
CB monitoring Aux. relays as
required
Carrier aided Distance Protection
relaying scheme complete in all
respect as described in the
specification.
Back up directional O/C and E/F
IDMTL relaying scheme with high
set unit complete in all respect
with PT fuse failure monitoring
feature as described in the
specification.
Neutral displacement relay for
220/132KV Transformer tertiary
protection
Back up restricted E/F relaying
scheme complete in all respect as
per specification.
Transformer trouble auxiliary
relaying scheme for Buchholz,
winding tem. Etc. as per
specification.
Transformer
differential
protection relaying scheme as
described in the specification,
complete in all respect
Tripping relaying scheme as
described in the specification.

2.

3.

4.

5.
6.
7.

8.

9.

10.

11.

12.

13.

WBSETCL / TECH SPEC / Rev.-1

Set

Set

As reqd.

Set

Set

Page 49 of 104

Control & Relay Panel

Q u a n t I t y
Sl. No.

14. i)
14. ii)
14. iii)

Particulars

Protection DC supply supervision

relay
B/Bar protn. DC supply supvn.
Relaying scheme
Incoming DC/Ann. Bus DC supply
supervision relays

14. iv)

Incoming DC/Ann. Bus DC failure

alarm accept relay AC operated

15.
16.

AC supply supervision relay

Flasher relay for CB discrepancy
switch
Timer for control switch & CB
discrepancy condition alarm
Test terminal block for protective
relays as required
Distance relay setting group
selector switch - 4 position
Overcurrent/ Earth fault relay
setting group Selector Switch, 3
position, 132/33KV TR OFF
132 KV Feeder Indication
Circuit label
Internally mounted equipment
like
heater
with
switch,
thermostat cubicle illumination
lamps, power socket, switches,
fuses, links etc. as described in
the main specification
Timer for bay transfer sequence
incomplete alarm, if required
Over Flux Protection relaying
scheme
Over Load Protection Relaying
Scheme

17.
18.
19.
20.

21.
22.

23.
24.
25.

NB:

Unit

Feeder

HT side of
220/132kV
& 220/33KV
Transformer

Bus
Coupler

Bus
Transfer

Set

Set

As reqd.
1+1(for
Ann. Bus
DC)
1

Nos

Nos

Nos
Nos

1
1

Nos
Nos

As reqd.

As reqd.

1
As reqd.

As reqd.

Nos

Nos

Nos

Set

Nos
Set

1
-

Set

Items in the BOM for 220KV side of 400/220KV transformer & 132KV side of 220/132KV
transformer shall be same as 220/132KV transformer except Neutral displacement relay,
differential relay, transformer trouble relay, REF relay, Over Flux Protection relay mentioned
under sl. no 9, 12, 11, 19, 10.24.

WBSETCL / TECH SPEC / Rev.-1

Page 50 of 104

Control & Relay Panel

20.01 (B)
220KV SIMPLEX TYPE CONTROL & PROTECTION PANEL FOR ONE & HALF
BREAKER SYSTEM:
Q u a n t I t y
Sl.
No.

Particulars

Unit

Feeder-Tie-Feeder

Transformer-Tie

A. RELAY PANEL
1.

Metering Device

a)
b)
c)
d)
e)

Ammeter
Voltmeter
Watt meter with transducer
Varmeter with transducer
Wiring for intelligent electronic
computer compatible energy
meter (0.2 class)
Test Terminal Block
Voltmeter Selector Switch
Frequency Meter
Control Device

Nos
Nos
Nos
Nos
Nos

6
2
2
2
2

6
2
2
2
2

Nos
Nos
Nos

2
2
2

2
2
2

Circuit Breaker Control Switch

Isolator Control Switch
Auto-reclose Selector Switch (if
necessary)
Synchronising Selector Switch
2 position
Multipin Synchronising Socket
(with
dummy
plug
where
necessary)
Carrier Selector Switch
Indication
LED
Position
Indicator
for
Position indicator of Circuit
Breaker (ON/OFF)
LED
Position
Indicator
for
Position indicator of Earth Switch
(ON/OFF)
LED Position Indicator of Isolator
Indicating lamp for incoming DC
fail/ANN. Bus DC fail and Bus PT
1&2 healthy
Circuit
breakerTrip
circuit
healthy indicating lamp
Trip circuit healthy Check Push
Button
C.B. Spring charge indicating
lamp where necessary

Nos
Nos
Nos

3
8
2

3
7
-

Nos

Set

Nos

Nos

8
10

7
10

Nos

Nos

f)
g)
h)
2.
a)
b)
c)
d)
e)

f)
3.
a)

b)

c)
d)

e)
f)
g)

WBSETCL / TECH SPEC / Rev.-1

Nos
Nos
Nos

Nos

Page 51 of 104

Control & Relay Panel

Q u a n t I t y
Sl.
No.
h)

4.
a)
b)
c)

d)

e)

Sl.
No.

Particulars
Push Button for
check, if required

Unit
C.B.

Spring

Other Devices
Circuit Label
Section of Mimic Diagram
Internally mounted equipment
like
Heater
with
Switch,
Thermostat, Cubicle Illumination
Lamps, Power Socket, Switches,
Fuses, Link etc. as described in
the main specification
One
Label
Indicating
Manufacturers
Name,
P.O.
Details, Drg. Ref. Nos. etc.
Annunciation Windows as reqd,
with Lamps, Accept/Reset/Test
Push Button etc. and associated
Relays if the annunciator relay is
attached with the windows

Particulars

Feeder-Tie-Feeder

Transformer-Tie

Nos

Nos
Set

2
1
1

2
1
1

48

48

Set

Set

nos

Unit

Quantity
Feeder

Transformer

Tie

B. PROTECTION PANEL
1.
2.

3.

4.
5.
6.

CB Trip Circuit and master trip

relay coil (86) Supervision Relay
Line CVT operated Under Voltage
Relay for line side earth switch
interlock
Bus VT supply selection relaying
scheme
for
metering
and
protection circuit complete in all
respect
Auxiliary
relays
for
C.B.
Closing/Tripping, if necessary
CB monitoring Aux. relays as
required
Carrier aided Distance Protection
relaying scheme complete in all
respect as described in the
specification.

WBSETCL / TECH SPEC / Rev.-1

Nos

1
Nos
1

1
1

1
1

Set

Set
Set

1
1
-

Set

Page 52 of 104

Control & Relay Panel

Sl.
No.
7.

8.

9.

10.

11.

12.
13.
14.
15.
16.

17.

Particulars
Back up directional O/C and E/F
IDMTL relaying scheme with high
set unit complete in all respect
with PT fuse failure monitoring
feature as described in the
specification.
Neutral displacement relay for
220/132KV Transformer tertiary
protection
Back up restricted E/F relaying
scheme complete in all respect
as per specification.
Transformer trouble auxiliary
relaying scheme for Buchholz,
winding tem. Etc. as per
specification.
Transformer
differential
protection relaying scheme as
described in the specification,
complete in all respect
Tripping relaying scheme as
described in the specification.
Incoming DC/Ann. Bus DC supply
supervision relays
Test terminal block for protective
relays as required
Circuit label
Internally mounted equipment
like
heater
with
switch,
thermostat cubicle illumination
lamps, power socket, switches,
fuses, links etc. as described in
the main specification
Over Flux Protection relaying
scheme

WBSETCL / TECH SPEC / Rev.-1

Unit

Set

Quantity
Feeder

Transformer

1 (3 O/C)

Tie

1
-

Set

Set

As reqd.

Set

Set

Nos
Nos

1
As reqd.

1
As reqd.

Nos

Set

Set

Page 53 of 104

As reqd.
2
1

Control & Relay Panel

20.01 (C)
220 KV DUPLEX TYPE CONTROL AND RELAY PANEL FOR TWO BUS (TWO
MAIN) GIS SYSTEM:
Q u a n t I t y
Sl. No.

Particulars

Unit
Feeder

HT side of
220/132kV
& 220/33KV
Transformer

Bus Coupler

A. FRONT PANEL:
1.

Metering Device

a)
b)
c)
d)

Ammeter
Voltmeter
Watt meter with transducer
Varmeter with transducer

Nos
Nos
Nos
Nos

3
1
1

3
1
1

3
2
1
1

e)

Nos

f)
g)

Wiring for intelligent electronic

computer
compatible
energy
meter (0.2 class)
Test Terminal Block
Voltmeter Selector Switch

Nos
Nos

1
-

1
-

h)
2.

Frequency Meter
Control Device

Nos

a)

Circuit Breaker Control Switch

discrepancy type with built-in
indicating lamp
Isolator Control Switch
Earth Isolator Control Switch
Auto-reclose Selector Switch (if
necessary)
Synchronising Selector Switch
2 position
Multipin Synchronising Socket
(with
dummy
plug
where
necessary)
Discrepancy Switch Steady Lamp
Cut-off Switch 2 position
Carrier Selector Switch
Bus VT Selector Switch VTI / VT2
Indication

Nos

Nos
Nos
Nos

3
4
1

3
4
-

4
6
-

Nos

Set

Nos

Nos
Nos

1
-

b)
c)
d)
e)
f)

g)
h)
i)
3.
a)
b)

LED Position Indicator for Position

indicator of Earth Switch
LED Position Indicator of Isolator

WBSETCL / TECH SPEC / Rev.-1

Nos
Nos

Page 54 of 104

Control & Relay Panel

Q u a n t I t y
Sl. No.

Particulars

Unit
Feeder

c)
d)

e)
f)
g)
h)
i)
j)
k)

Indicating lamp for incoming DC

fail/ANN. Bus DC fail
Push Button for Incoming DC
fail/ANN. Bus DC fail alarm accept
& test
Circuit breakerTrip circuit healthy
indicating lamp
Trip circuit healthy Check Push
Button
C.B.Spring charge indicating lamp
where necessary
Push Button for C.B. Spring
check, if required
Test PB for incoming DC
supervision etc
Indication for Distance Protn.
Carrier Signal recd., if required
Bus VT-1/VT-2 supply healthy
indicating lamp

HT side of
220/132kV
& 220/33KV
Transformer

Bus Coupler

Nos

Nos

Nos

Nos

Nos

Nos

Nos

2 For incming DC &

incoming AC

Nos
Nos

1
-

Nos
Set

2
1

2
1

2
1

Set

Set

nos

24

32

24

Set

4.
a)
b)
c)

Circuit Label
Section of Mimic Diagram
Internally mounted equipment
like
Heater
with
Switch,
Thermostat, Cubicle Illumination
Lamps, Power Socket, Switches,
Fuses, Link etc. as described in
the main specification
d)
One
Label
Indicating
Manufacturers
Name,
P.O.
Details, Drg. Ref. Nos. etc.
e)
Annunciation Windows with DC
fail annunciation as reqd, with
Lamps, Accept/Reset/Test Push
Button etc. and associated Relays
if the annunciator relay is
attached with the windows
f)
Common Bell, Hooter, Associated
relays etc. for Annunciation
Scheme
B. REAR PANEL:
WBSETCL / TECH SPEC / Rev.-1

Page 55 of 104

Control & Relay Panel

Q u a n t I t y
Sl. No.

Particulars

Unit
Feeder

1.

2.

3.

4.

5.
6.
6a).

7.

8.

9.

10.

11.

CB Trip Circuit and master trip

relay coil (86 & 96) Supervision
Relay
Line CVT operated Under Voltage
Relay for line side earth switch
interlock
Breaker failure relaying scheme
complete with Aux. relay, timers
etc.
Bus VT supply selection relaying
scheme
for
metering
and
protection circuit complete in all
respect
Auxiliary
relays
for
C.B.
Closing/Tripping, if necessary
CB monitoring Aux. relays as
required
GIS
other
compartment
monitoring
Aux.
relays
as
required
Carrier aided Distance Protection
relaying scheme complete in all
respect as described in the
specification.
Back up directional O/C and E/F
IDMTL relaying scheme with high
set unit complete in all respect
with PT fuse failure monitoring
feature as described in the
specification.
Neutral displacement relay for
220/132KV Transformer tertiary
protection
Back up restricted E/F relaying
scheme complete in all respect as
per specification.
Transformer trouble auxiliary
relaying scheme for Buchholz,
winding tem. Etc. as per
specification.

WBSETCL / TECH SPEC / Rev.-1

HT side of
220/132kV
& 220/33KV
Transformer

Bus Coupler

Nos

Nos

Set

Set

Set

Set

Set

Set

Set

1 (3 O/C)

As reqd.

Set

Set

Page 56 of 104

Control & Relay Panel

Q u a n t I t y
Sl. No.

Particulars

Unit
Feeder

12.

13.
14.
15.
16.
17.
18.
19.
20.

21.
22.

23.
24.

Transformer
differential
protection relaying scheme as
described in the specification,
complete in all respect
Tripping relaying scheme as
described in the specification.
Incoming DC/Ann. Bus DC supply
supervision relays
AC supply supervision relay
Flasher relay for CB discrepancy
switch
Timer for control switch & CB
discrepancy condition alarm
Test terminal block for protective
relays as required
Distance relay setting group
selector switch - 4 position
Overcurrent/ Earth fault relay
setting group Selector Switch, 3
position, 132/33KV TR OFF
132 KV Feeder Indication
Circuit label
Internally mounted equipment
like
heater
with
switch,
thermostat cubicle illumination
lamps, power socket, switches,
fuses, links etc. as described in
the main specification
Timer for bay transfer sequence
in complete alarm, if required
Over Flux Protection relaying
scheme

WBSETCL / TECH SPEC / Rev.-1

HT side of
220/132kV
& 220/33KV
Transformer

Bus Coupler

Set

Set

Nos

Nos
Nos

1
1

Nos

Nos

As reqd.

As reqd.

As reqd.

Nos

Nos

Nos

Set

Nos

Set

Page 57 of 104

Control & Relay Panel

20.02 (A) 132KV DUPLEX TYPE CONTROL AND RELAY PANEL FOR TWO MAIN & ONE
TRANSFER BUS SYSTEM:

A.

Feeder

y
Bus Coupler

Bus Transfer

Unit

Sl.
No.

n t

of
side
HT
132/33KV
Transformer

Particulars

u a

of
side
LT
220/132KV
Transformer

FRONT PANEL:

1. Metering Device
a)
b)
c)
d)
e)

f)
2.
a)

b)
c)
d)
e)
f)

g)
h)
i)
j)
k)
3.
a)

b)
c)

Ammeter
Wattmeter with transducer
Varmeter with transducer
Voltmeter
Wiring for intelligent electronic
computer compatible energy
meter (0.2 class)
Test Terminal Block
Control Device
Circuit Breaker Control Switch
discrepancy type with built-in
indicating lamp
Isolator Control Switch
Auto-reclose Selector Switch (if
any)
Trip Transfer Switch
Synchronising Selector Switch
Multipin Synchronising Socket
(with dummy plug where
necessary)
Discrepancy Switch Steady Lamp
Cut-off Swtich
Voltmeter Selector Switch
Carrier Selector Switch
Bus Transfer Bay Protn. IN/OUT
Selector Switch. 2 position
Bus VT Selector Switch VT1/VT2
Indication
LED Position Indicator for
position indication of Earth
Switch
LED Position Indicator for
position indication of Isolator
Indicating Lamp for incoming DC
fail/ANN. Bus DC fail

WBSETCL / TECH SPEC / Rev.-1

Nos
Nos
Nos
Nos

3
1
1
-

3
1
1
-

3
1
-

3
1
1
-

3
1
1
2
-

Nos

Nos

Nos

Nos
Nos

4
1

4
-

4
-

3
-

2
-

Nos
Nos
Nos

1
1
1

1
1
1

1
-

1
1

1
1

Nos
Nos
Nos
Nos

1
-

2
-

Nos

Nos

Nos
Nos

4
-

4
-

4
-

3
-

Page 58 of 104

2
1

Control & Relay Panel

e)
f)
g)
h)
i)
j)
k)
4.
a)
b)
c)

d)

e)

f)

B.
1.

of
side
HT
132/33KV
Transformer

n t

Push Button Incoming DC

fail/ANN. Bus DC fail alarm
accept & test
Bus PT supply healthy indicating
lamp
Trip Circuit healthy indicating
lamp
Trip Circuit healthy Check Push
Button
C.B. Spring Charge Indicating
Lamp where necessary
Push Button for C.B. Spring
charge check if required
Test Push Button for Protection
DC & Incoming AC Supervision
Indication for Distance Protn.
Carrier Signal recd., if required
Other Devices

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Circuit Label
Section of Mimic Diagram
Internally mounted equipment
like
Heater
with
Switch,
Thermostat, Cubicle Illumination
Lamps, Power Socket, Switches,
Fuses, Link etc. as described in
the main specification
One
Label
indicating
Manufacturer's
neme,
P.O.Details, Drg. Ref. Nos. etc.
Annunciation
Windows
with
Lamps, Accept/Reset/Test Puish
Button etc. and associated
relays if the annunciator relay is
attached with the windows
Common bell, hooter, associated
relays etc. for annunciation
scheme
REAR PANEL:

Nos
Set

2
1

2
1

2
1

2
1

2
1
1

Set

Set

Supervision Relay for CB Trip

Circuit and master Trip Relay
healthy check

Nos

Feeder

WBSETCL / TECH SPEC / Rev.-1

Bus Coupler

Unit

Bus Transfer

Particulars
Sl.
No.

d)

u a

of
side
LT
220/132KV
Transformer

1
Set

1
16

Nos

16

16

16

16

Page 59 of 104

Control & Relay Panel

2.

3.

5.
6.
7.
i)

7.
ii)

8.

9.

10.

11.

12.

13.
14.
15.

WBSETCL / TECH SPEC / Rev.-1

y
Bus Coupler

Feeder
Line
CVT operated
under
Voltage Relay for line side earth
switch interlock
Breaker failure relaying scheme
complete with Aux. relay, timers
etc.
Auxiliary
relays
for
C.B.
Closing/Tripping, if necessary
CB monitoring Aux. relays as
required
Distance Protection Scheme
complete in all respect as per
specification, where the line
length is more than 3km.
Line
Differential
Protection
Scheme complete in all respect
as per specification, where the
line length is less than 3km.
Back up directional O/C and E/F
IDMTL relaying scheme with
high set unit complete in all
respect with PT fuse failure
monitoring feature as described
in the specification.
Transformer
differential
protection relaying schemes
described in the specification
complete in all respect
Back up restricted E/F relaying
scheme complete in all respect
as per specification.
Definite time E/F relay for ET
protection
(For Yd Transformer)
Transformer trouble auxiliary
relaying scheme for Buchholz,
winding temp. etc.
Tripping relaying scheme
Protection DC supply supervision
relay
Incoming DC/Ann. Bus DC
supervision relays

Bus Transfer

Unit

Sl.
No.

n t

of
side
HT
132/33KV
Transformer

Particulars

u a

of
side
LT
220/132KV
Transformer

Nos

Set

Set
Set

1
1

1
1

1
1

1
1

Set

Set

1
1
-

Set

1 (3 O/C)

1 (3 O/C)

Set

Set

Set

Set

As reqd.

Set
Nos

1
1

1
1

1
1

1
1

Nos

1
2

Page 60 of 104

Control & Relay Panel

16.
17.

Nos
Nos

18.
19.
20.
21.
22.

23.
24.

25.

Feeder
-

Bus Coupler

AC supply supervision relay

Flasher relay for CB discrepancy
switch
Timer for control switch & CB
discrepancy condition alarm
Incoming DC/Ann Bus DC fail
alarm accept relay, AC operated
Test
terminal
block
for
protective relays as required
Distance relay setting group
selector switch - 4 position
Overcurrent/ Earth fault relay
setting group Selector Switch, 3
position, 132/33KV TR OFF
132 KV Feeder Indication
Circuit Label
Internally mounted equipment
like
heater
with
switch,
thermostat cubicle illumination
lamps, power socket, switches,
fuses, links etc. as described in
the main specification
Timer for bay transfer sequence
in complete alarm, if required

Bus Transfer

Unit

n t

of
side
HT
132/33KV
Transformer

Particulars
Sl.
No.

u a

of
side
LT
220/132KV
Transformer

1
1
1

Nos

Nos
Set
nos

As
reqd.
-

As reqd.

As reqd.

As
reqd.
1

As
reqd.
-

Nos

Nos

Set

As req

As reqd.

As reqd.

As
reqd.

As
reqd.

Nos

20.02 (B) 132KV DUPLEX TYPE CONTROL AND RELAY PANEL FOR TWO BUS (MAIN &
TRANSFER) SYSTEM:

A.

FRONT PANEL:

1.

Metering Device

a)
b)
c)
d)

Ammeter
Wattmeter with transducer
Varmeter with transducer
Voltmeter

WBSETCL / TECH SPEC / Rev.-1

3
1
1
-

Page 61 of 104

3
1
1
-

3
1
-

Bus Transfer

Unit

Nos
Nos
Nos
Nos

n t

of
side
HT
132/33KV
Transformer

Particulars

Feeder

Sl.
No.

u a

of
side
LT
220/132KV
Transformer

3
1
1
1
Control & Relay Panel

e)

f)
2.
a)

b)
c)
d)
e)
f)

g)
h)
i)

3.
a)

b)
c)
d)

e)
f)
g)
h)

Feeder
Wiring for intelligent electronic
computer compatible energy
meter (0.2 class)
Test Terminal Block
Control Device
Circuit Breaker Control Switch
discrepancy type with built-in
indicating lamp
Isolator Control Switch
Auto-reclose Selector Switch (if
any)
Trip Transfer Switch
Synchronising Selector Switch
Multipin Synchronising Socket
(with dummy plug where
necessary)
Discrepancy Switch Steady Lamp
Cut-off Swtich
Voltmeter Selector Switch
Carrier Selector Switch
Bus Transfer Bay Protn. IN/OUT
Selector Switch. 2 position
Indication
LED Position Indicator for
position indication of Earth
Switch
LED Position Indicator for
position indication of Isolator
Indicating Lamp for incoming DC
fail/ANN. Bus DC fail
Push Button Incoming DC
fail/ANN. Bus DC fail alarm
accept & test
Bus PT supply healthy indicating
lamp
Trip Circuit healthy indicating
lamp
Trip Circuit healthy Check Push
Button
C.B. Spring Charge Indicating
Lamp where necessary

WBSETCL / TECH SPEC / Rev.-1

y
Bus Transfer

Unit

Sl.
No.

n t

of
side
HT
132/33KV
Transformer

Particulars

u a

of
side
LT
220/132KV
Transformer

Nos

Nos

Nos

Nos
Nos

3
1

3
-

3
-

5
-

Nos
Nos
Nos

1
1
1

1
1
1

1
-

1
1

Nos
Nos
Nos

1
1
-

Nos

Nos
Nos

3
-

3
-

3
-

5
1

Nos

Nos

Nos

Nos

Nos

Page 62 of 104

Control & Relay Panel

j)
k)
4.
a)
b)
c)

d)

e)

f)

B.
1.

2.

3.

5.
6.

y
of
side
HT
132/33KV
Transformer

n t

Unit

Push Button for C.B. Spring

charge check if required
Test Push Button for Protection
DC & Incoming AC Supervision
Indication for Distance Protn.
Carrier Signal recd., if required
Other Devices

Nos

Nos

Nos

Circuit Label
Section of Mimic Diagram
Internally mounted equipment
like
Heater
with
Switch,
Thermostat, Cubicle Illumination
Lamps, Power Socket, Switches,
Fuses, Link etc. as described in
the main specification
One
Label
indicating
Manufacturer's
neme,
P.O.Details, Drg. Ref. Nos. etc.
Annunciation
Windows
with
Lamps, Accept/Reset/Test Push
Button etc. and associated
relays if the annunciator relay is
attached with the windows
Common bell, hooter, associated
relays etc. for annunciation
scheme
REAR PANEL:

Nos
Set

2
1

2
1

2
1

2
1

Set

Set

Nos

16

16

Set

Supervision Relay for CB Trip

Circuit and master Trip Relay
healthy check
Line
CVT operated
under
Voltage Relay for line side earth
switch interlock
Breaker failure relaying scheme
complete with Aux. relay, timers
etc.
Auxiliary
relays
for
C.B.
Closing/Tripping, if necessary
CB monitoring Aux. relays as
required

Nos

Nos

Set

Set
Set

1
1

1
1

1
1

1
1

Feeder

WBSETCL / TECH SPEC / Rev.-1

Page 63 of 104

16

Bus Transfer

Particulars
Sl.
No.

i)

u a

of
side
LT
220/132KV
Transformer

16

Control & Relay Panel

7.
i)

7.
ii)

8.

9.

10.

11.

12.

13.
14.
15.
16.
17.
18.
19.
20.

Feeder
Distance Protection Scheme
complete in all respect as per
specification, where the line
length is more than 3km.
Line
Differential
Protection
Scheme complete in all respect
as per specification, where the
line length is less than 3km.
Back up directional O/C and E/F
IDMTL relaying scheme with
high set unit complete in all
respect with PT fuse failure
monitoring feature as described
in the specification.
Transformer
differential
protection relaying schemes
described in the specification
complete in all respect
Back up restricted E/F relaying
scheme complete in all respect
as per specification.
Definite time E/F relay for ET
protection
(For Yd Transformer)
Transformer trouble auxiliary
relaying scheme for Buchholz,
winding temp. etc.
Tripping relaying scheme
Protection DC supply supervision
relay
Incoming DC/Ann. Bus DC
supervision relays
AC supply supervision relay
Flasher relay for CB discrepancy
switch
Timer for control switch & CB
discrepancy condition alarm
Incoming DC/Ann Bus DC fail
alarm accept relay, AC operated
Test
terminal
block
for
protective relays as required

WBSETCL / TECH SPEC / Rev.-1

y
Bus Transfer

Unit

Sl.
No.

n t

of
side
HT
132/33KV
Transformer

Particulars

u a

of
side
LT
220/132KV
Transformer

Set

Set

Set

1 (3 O/C)

1 (3 O/C)

Set

Set

Set

Set

As reqd.

Set
Nos

1
1

1
1

1
1

1
1

Nos
Nos
Nos

2
1
1

Nos

Nos

As req

As reqd.

As reqd.

As
reqd.

Set

Page 64 of 104

Control & Relay Panel

22.

23.
24.

25.

y
of
side
HT
132/33KV
Transformer

n t

Unit

Distance relay setting group

selector switch - 4 position
Overcurrent/ Earth fault relay
setting group Selector Switch, 3
position, 132/33KV TR OFF
132 KV Feeder Indication
Circuit Label
Internally mounted equipment
like
heater
with
switch,
thermostat cubicle illumination
lamps, power socket, switches,
fuses, links etc. as described in
the main specification
Timer for bay transfer sequence
in complete alarm, if required

nos

Nos

Nos

Set

As req

As reqd.

As reqd.

As
reqd.

Nos

Feeder

Bus Transfer

Particulars
Sl.
No.

21.

u a

of
side
LT
220/132KV
Transformer

20.02 (C)
132 KV DUPLEX TYPE CONTROL AND RELAY PANEL FOR TWO BUS (TWO
MAIN) GIS SYSTEM:

A.

FRONT PANEL:

1.

Metering Device

a)
b)
c)
d)
e)

Ammeter
Wattmeter with transducer
Varmeter with transducer
Voltmeter
Wiring
for
intelligent
electronic
computer
compatible energy meter (0.2
class)
Test Terminal Block
Control Device

f)
2.

WBSETCL / TECH SPEC / Rev.-1

Bus Coupler

Feeder

Sl.
No.

side
HT
132/33KV
Transformer

Unit

side
LT
220/132KV
Transformer

Particulars

n t
of

u a

of

Nos
Nos
Nos
Nos
Nos

3
1
1
1

3
1
1
-

3
1
1

3
1
1
2
-

Nos

Page 65 of 104

Control & Relay Panel

b)
c)
d)
e)
f)

g)
h)
i)
j)
3.
a)

b)
c)
d)

e)
f)
g)
h)
i)
j)

Bus Coupler

Circuit Breaker Control Switch

discrepancy type with built-in
indicating lamp
Isolator Control Switch
Earth Isolator Control Switch
Auto-reclose Selector Switch
(if any)
Synchronising Selector Switch

Nos

Nos
Nos
Nos

3
4
1

3
4
-

3
4
-

4
6
-

Nos

Multipin Synchronising Socket

(with dummy plug where
necessary)
Discrepancy Switch Steady
Lamp Cut-off Swtich
Voltmeter Selector Switch
Carrier Selector Switch
Earthing Tr. selector switch
Indication

Nos

Nos

Nos
Nos
Nos

1
-

2
-

Nos

4
4
6

6
8

Feeder
LED Position Indicator for
position indicaton of Earth
Switch Isolator
Isolator
Status
Indicating
Lamps Red/Green
Indicating Lamp for incoming
DC fail/ANN. Bus DC fail
Push Button Incoming DC
fail/ANN. Bus DC fail alarm
accept & test
Bus
PT
supply
healthy
indicating lamp
Trip Circuit healthy indicating
lamp
Trip Circuit healthy Check
Push Button
C.B. Spring Charge Indicating
Lamp where necessary
Push Button for C.B. Spring
charge check if required
Test
Push
Button
for
Incoming DC Supervision

WBSETCL / TECH SPEC / Rev.-1

side
HT
132/33KV
Transformer

Unit

side
LT
220/132KV
Transformer

Particulars
Sl.
No.
a)

n t
of

u a

of

Nos

4
6

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Page 66 of 104

Control & Relay Panel

4.
a)
b)
c)

d)

e)

f)

Bus Coupler

Circuit Label
Section of Mimic Diagram
Internally mounted equipment
like Heater with Switch,
Thermostat,
Cubicle
Illumination Lamps, Power
Socket, Switches, Fuses, Link
etc. as described in the main
specification
One
Label
indicating
Manufacturer's
neme,
P.O.Details, Drg. Ref. Nos.
etc.
Annunciation Windows with
DC fail annunciation as reqd,
with
Lamps,
Accept/Reset/Test
Push
Button etc. and associated
Relays if the annunciator relay
is attached with the windows
Common
bell,
hooter,
associated relays etc. for
annunciation scheme

Nos
Set

2
1

2
1

2
1

2
1

Set

Set

As Req

As Req

As Req

As Req

Set

Nos

Nos

Set

Feeder

1.

Supervision Relay for CB Trip

Circuit and master Trip Relay
healthy check
Line CVT operated under
Voltage Relay for line side
earth switch interlock
Breaker
failure
relaying
scheme complete with Aux.
relay, timers etc.

WBSETCL / TECH SPEC / Rev.-1

side
HT
132/33KV
Transformer

Nos

side
LT
220/132KV
Transformer

Indication for Distance Protn.

Carrier
Signal
recd.,
if
required
Other Devices

REAR PANEL:

3.

Unit

B.

2.

Particulars
Sl.
No.
k)

n t
of

u a

of

Nos

Page 67 of 104

Control & Relay Panel

5.
6.
6a).

7.

8.

9.

10.

11.

12.

13.
14.
15.

Bus Coupler

Auto-reclose relaying scheme

complete with dead line
charging/check syn. Relaying,
Auxiliary relays, lock out
relays, timer etc.

Set

Auxiliary relays for C.B.

Closing/Tripping, if necessary
CB monitoring Aux. relays as
required
GIS
other
compartment
monitoring Aux. relays as
required
Distance Protection Scheme
complete in all respect as per
specification
Back up directional O/C and
E/F IDMTL relaying scheme
with high set unit complete in
all respect with PT fuse failure
monitoring
feature
as
described in the specification.
Transformer
differential
protection relaying schemes
described in the specification
complete in all respect
Back up restricted E/F
relaying scheme complete in
all
respect
as
per
specification.
Definite time E/F relay for ET
protection
(For Yd Transformer)
Transformer trouble auxiliary
relaying scheme for Buchholz,
winding temp. etc.
Tripping relaying scheme

Set

Set

Set

Set

Set

1 (3 O/C)

1 (3 O/C)

1(Non
directional)

Set

Set

Set

Set

As reqd.

Set

Incoming
DC
supply
supervision relay
Ann. Bus DC supervision
relays

Nos

Nos

Feeder

WBSETCL / TECH SPEC / Rev.-1

Page 68 of 104

side
HT
132/33KV
Transformer

Unit

side
LT
220/132KV
Transformer

Particulars
Sl.
No.
4.

n t
of

u a

of

Control & Relay Panel

18.

Bus Coupler

AC supply supervision relay

Flasher
relay
for
CB
discrepancy switch
Timer for control switch & CB

Nos
Nos

1
1

Nos

Nos

Set

As req

As reqd.

As reqd.

As reqd.

nos

Nos

Nos

Set

As req

As reqd.

As reqd.

As reqd.

Nos

Feeder

side
HT
132/33KV
Transformer

Unit

side
LT
220/132KV
Transformer

Particulars
Sl.
No.
16.
17.

n t
of

u a

of

discrepancy condition alarm

19.

20.
21.
22.

23.
24.

25.

Incoming DC/Ann Bus DC fail

alarm
accept
relay,
AC
operated
Test terminal
block
for
protective relays as required
Distance relay setting group
selector switch - 4 position
Overcurrent/ Earth fault relay
setting group Selector Switch,
3 position, 132/33KV TR
OFF 132 KV Feeder
Indication
Circuit Label
Internally mounted equipment
like heater with switch,
thermostat
cubicle
illumination lamps, power
socket, switches, fuses, links
etc. as described in the main
specification
Timer
for
bay
transfer
sequence in complete alarm,
if required

WBSETCL / TECH SPEC / Rev.-1

Page 69 of 104

Control & Relay Panel

20.03(A)
TRANSFER)

33KV SIMPLEX TYPE CONTROL AND RELAY PANEL FOR TWO BUS (MAIN &
SYSTEM

Sl.
No.

Particulars

1.

Metering Device

a)
b)
c)

Ammeter
Voltmeter
Wiring
for
intelligent
electronic
computer
compatible energy meter
(0.2 class)
Test Terminal Block
Control Device

Q u a n t I t y
Feeder
LT
side
of
220/33KV
&
132/33KV
Transformer

HT side of
33/11KV
Transformer

Bus
Transfer

Nos
Nos
Nos

3
1

3
-

3
1

3
1
-

Nos

Circuit
Breaker
Control
Switch 3-position, Spring
return
Voltmeter Selector Switch
Trip Transfer Switch
Overcurrent/ Earth fault
relay setting group Selector
Switch,
3

position,
132/33KV TR OFF 132
KV Feeder Indication
Five position selector switch
for Earthing Transformer
selection
U/F selector switch

Nos

Nos
Nos

1
-

Nos

Nos

Nos

e)

Selector Sw for trip selection

in power injection mode

Nos

3.

Indication

a)

LED Position Indicator for CB

status
LED Position Indicator for
Isolator & Earth Switch
status
Indicating
Lamp
for
incoming DC fail/Ann. Bus
DC fail
Incoming DC fail/ann. Bus
DC fail alarm accept & Test
Fuse button
Bus VT supply healthy
indicating lamp
Trip circuit healthy indicating

d)
2.
a)

b)
c)
d)

e)

d)

b)

c)

d)

e)
f)

WBSETCL / TECH SPEC / Rev.-1

Unit

Nos

Nos

Nos

Nos

Nos

Nos

Page 70 of 104

Control & Relay Panel

Sl.
No.

g)
h)
i)
j)
k)

4.

Particulars

lamp
Trip circuit healthy check
push button
CB spring charge indicating
lamp
Push Button for CB spring
charge check
CB Auto Trip indicator
Test Push Button for panel
protection DC supervision
and AC supervision
RELAYS

Unit

Q u a n t I t y
Feeder
LT
side
of
220/33KV
&
132/33KV
Transformer

HT side of
33/11KV
Transformer

Bus
Transfer

Nos

Nos

Nos

Nos
Nos

1
1

1
1

1
1

1
2

a)

Supervision Relay for CB Trip

Circuit and master Trip Relay
healthy check

Nos

b)

Auxiliary
relay
for
CB
closing/tripping
If necessary
CB monitoring Aux. relays as
reqd.
Directional O/C and E/F
IDMTL relaying scheme with
high set unit complete in all
respect with PT fuse failure
monitoring
feature
as
described
in
the
specification.
Restricted
E/F
relaying
scheme complete in all
respect as per specification.
Power , Earthing & Station
service Transformer Trouble
auxiliary relaying scheme for
Buchholz,
winding
temperature etc.
Tripping Relaying scheme
including lock out feature
Protection
DC
supply
supervision relays
Incoming DC/Ann. Bus DC
supply supervision relays
AC supply supervision relays
Incoming DC / Ann. Bus DC
fail alarm accept relay, AC

Set

Set

Set

Set

Set

As reqd.

As reqd.

Set

Nos

Nos
Nos
Nos

2
1
1

c)
d)

e)

f)

g)
h)
i)
j)
k)

WBSETCL / TECH SPEC / Rev.-1

Page 71 of 104

Control & Relay Panel

Sl.
No.

l)
m)

5.
a)
b)
c)

d)

e)

f)

Particulars

Unit

operated
Test block for protective
relays
Under frequency relay along
with contact multiplication
relay
Other Devices :
Circuit Label
Section of Mimic Diagram
Internally
mounted
equipment like Heater with
Switch, Thermostat, Cubicle
Illumination Lamps, power
socket, switches, fuses, link
etc. as described in the main
specification
One
Label
Indicating
Manufacturers Name, P.O.
Details, Drg. Ref. Nos. etc.
Annunciation
Windows,
Lamps,
Accept/Reset/Test
Push Button etc. associated
Relays if the annunciator
relay is attached with the
windows.
Common
bell,
hooter,
associated relays etc. for
annunciation scheme

Q u a n t I t y
Feeder
LT
side
of
220/33KV
&
132/33KV
Transformer

HT side of
33/11KV
Transformer

Bus
Transfer

Nos

As
reqd.

As reqd.

As reqd.

As reqd.

Nos

Nos
Set

1
1

1
1

1
1

1
1

Set

Set

Nos

12

12

12

20

Set

20.03(B) 33 KV SIMPLEX TYPE CONTROL AND RELAY PANEL FOR TWO BUS (With Bus
Section) INDOOR TYPE SWITCHGEAR SYSTEM:
Sl.

Particulars

Unit

No.

Q u a n t I
Feeder

1.

Metering Device

a)
b)
c)

Ammeter
Voltmeter
Wiring
for
electronic

intelligent
computer

WBSETCL / TECH SPEC / Rev.-1

Nos
Nos
Nos

LT side of 220/33KV &

132/33KV Transformer

3
1

Page 72 of 104

3
-

t y
Bus
Coupler

3
2
-

Control & Relay Panel

Sl.

Particulars

Unit

No.

d)
2.
a)

b)
c)

d)
e)
3.
a)
b)

c)

d)
e)
f)
g)
h)
i)
j)

4.
a)

Q u a n t I
Feeder

compatible energy
(0.2 class)
Test Terminal Block
Control Device

LT side of 220/33KV &

132/33KV Transformer

t y
Bus
Coupler

meter
Nos

Circuit
Breaker
Control
Switch 3-position, Spring
return
Voltmeter Selector Switch
Five position selector switch
for Earthing Transformer
selection
U/F selector switch
Selector Sw for trip selection
in power injection mode
Indication

Nos

Nos
Nos

2
-

Nos
Nos

1
1

LED Position Indicator for CB

status
Indicating
Lamp
for
incoming DC fail/Ann. Bus
DC fail
Incoming DC fail/ann. Bus
DC fail alarm accept & Test
Push button
Bus VT supply healthy
indicating lamp
Trip circuit healthy indicating
lamp
Trip circuit healthy check
push button
CB spring charge indicating
lamp
Push Button for CB spring
charge check
CB Auto Trip indicator
Test Push Button for panel
protection DC supervision
and AC supervision
RELAYS

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos

Nos
Nos

1
1

1
1

1
2

Supervision Relay for CB Trip

Circuit and master Trip Relay
healthy check

Nos

WBSETCL / TECH SPEC / Rev.-1

Page 73 of 104

Control & Relay Panel

Sl.

Particulars

Unit

No.

b)

c)
d)

e)

f)

g)
h)
i)
j)
k)

l)
m)

5.
a)
b)
c)

Q u a n t I
Feeder

Auxiliary
relay
for
CB
closing/tripping
If necessary
CB monitoring Aux. relays as
reqd.
Directional O/C and E/F
IDMTL relaying scheme with
high set unit complete in all
respect with PT fuse failure
monitoring
feature
as
described
in
the
specification.
Restricted
E/F
relaying
scheme complete in all
respect as per specification.
Power , Earthing & Station
service Transformer Trouble
auxiliary relaying scheme for
Buchholz,
winding
temperature etc.
Tripping Relaying scheme
including lock out feature
Protection
DC
supply
supervision relays
Incoming DC/Ann. Bus DC
supply supervision relays
AC supply supervision relays
Incoming DC / Ann. Bus DC
fail alarm accept relay, AC
operated
Test block for protective
relays
Under frequency relay along
with contact multiplication
relay
Other Devices :
Circuit Label
Section of Mimic Diagram
Internally
mounted
equipment like Heater with
Switch, Thermostat, Cubicle
Illumination Lamps, power

WBSETCL / TECH SPEC / Rev.-1

LT side of 220/33KV &

132/33KV Transformer

t y
Bus
Coupler

Set

Set

Set

Set

Set

As reqd.

Set

Nos

Nos
Nos
Nos

2
1
1

Nos

As
reqd.

As reqd.

As reqd.

Nos

Nos
Set

1
1

1
1

1
1

Set

Page 74 of 104

Control & Relay Panel

Sl.

Particulars

Unit

No.

d)

e)

f)

Q u a n t I
Feeder

socket, switches, fuses, link

etc. as described in the main
specification
One
Label
Indicating
Manufacturers Name, P.O.
Details, Drg. Ref. Nos. etc.
Annunciation
Windows,
Lamps,
Accept/Reset/Test
Push Button etc. associated
Relays if the 75nnunciator
relay is attached with the
windows.
Common
bell,
hooter,
associated relays etc. for
annunciation scheme

t y

LT side of 220/33KV &

132/33KV Transformer

Bus
Coupler

Set

Nos

12

12

20

Set

20.03(C) 33 KV SIMPLEX TYPE CONTROL AND RELAY PANEL FOR CAPACITOR BANK:
Sl.
No.

Particulars

1.

Metering Device

a)
b)
c)
d)
2.

Ammeter
Voltmeter
VARmeter with transducers
Test Terminal Block
Control Device

a)

Circuit Breaker Control

Spring return
Voltmeter Selector Switch
Indication

b)
3.
a)
a)
e)
f)
g)
h)
i)

Unit

Quantity
Capacitor Bank Bay

Switch

3-position,

LED Position Indicator for CB status

LED Position Indicator for Isolator & Earth
Switch status
Trip circuit healthy indicating lamp
Trip circuit healthy check push button
CB spring charge indicating lamp
Push Button for CB spring charge check
CB Auto Trip indicator

WBSETCL / TECH SPEC / Rev.-1

Nos
Nos
Nos
Nos

3
1
1
1

Nos

Nos

Nos
Nos

1
As applicable

Nos
Nos
Nos
Nos
Nos

2
1
1
1
1

Page 75 of 104

Control & Relay Panel

Sl.
No.

Particulars

j)

Test Push Button for panel protection DC

supervision
RELAYS

Nos

Supervision Relay for CB Trip Circuit and

master Trip Relay healthy check
Auxiliary relay for CB closing/tripping
If necessary
CB monitoring Aux. relays as reqd.
Non - Directional O/C and E/F IDMTL relaying
scheme with high set unit complete in all
respect with PT fuse failure monitoring feature
as described in the specification.
Unbalance Protection scheme relay along with
timer for double star connected capacitor bank
with Floating Neutral.
Over voltage & Under voltage protn scheme as
per specification.
Tripping Relaying scheme including lock out
feature
Timer suitable to prevent CB closing within
capacitor discharging time
Protection DC supply supervision relays
Test block for protective relays
Other Devices :

Nos

Set

Set

Set

Set

Set

Set

Nos
Nos

1
As reqd.

Circuit Label
Section of Mimic Diagram
Internally mounted equipment like Heater with
Switch, Thermostat, Cubicle Illumination
Lamps, power socket, switches, fuses, link etc.
as described in the main specification
One Label Indicating Manufacturers Name,
P.O. Details, Drg. Ref. Nos. etc.
Annunciation
Windows,
Lamps,

Nos
Set

1
1

Set

Set

Accept/Reset/Test Push Button etc. associated

Nos

12

4.
a)
b)
c)
d)

e)

f)
g)
h)
h)
l)
5.
a)
b)
c)

d)
e)

Unit

Quantity
Capacitor Bank Bay

Relays if the 76nnunciator relay is attached

with the windows.

WBSETCL / TECH SPEC / Rev.-1

Page 76 of 104

Control & Relay Panel

20.04 (A) 400KV DUPLEX TYPE CONTROL AND RELAY PANEL FOR TWO MAIN AND ONE
TRANSFER BUS AIS SYSTEM:
Unit
Sl.
No.

Quantity

Particulars
Feeder

HT side of
400/220KV
transformer

Bus
reactor

Bus
coupler

Bus transfer

3
2
1

A. FRONT PANEL:
1

Metering Device

a)
b)
c)

Ammeter
Voltmeter
Wattmeter
with
transducers
varmeter
with
transducers
Provision for RWTI
meter
Wiring for TVM for
Export/Import

Nos
Nos
Nos

3
1
1

3
1

Nos

Nos

Test terminal block

Voltmeter
selector
switch
Frequency meter
Recording voltmeter
(Digital)
Recording frequency
meter (Digital)
Remote
winding
temperature
Indicator
selector
switch
Control Device

Nos
Nos

1
1

Circuit
breaker
control
switch
Discrepancy
type
with
builtin
Indicator lamp
Isolator
control
switch
Auto-reclose selector
switch
Trip transfer switch
Line VT/ Bus VT
selector switch, 4
position, Line VTInter1-Inter2-Bus VT
Synchronising

Nos

Nos

Nos

Nos
Nos

1
1

Nos

d)
e)
f)
g)
h)
i)
j)
k)
l)

2
a)

b)
c)
d)
e)

f)

WBSETCL / TECH SPEC / Rev.-1

Nos

2
1

Nos

Nos

Nos
Nos

1
-

Page 77 of 104

Control & Relay Panel

Unit
Sl.
No.

g)
h)

i)

j)

3
a)

b)

c)

d)

e)

f)
4
a)
b)
c)

Quantity

Particulars

selector switch, 2
position
Multipin
synchronising socket
Discrepancy
switch
steady lamp Cut off
switch, 2- position
DC supply selector
switch, 3 position,
Supply-1/
Independent
/Supply-2
VT selector switch, 2
position, VT 1 / VT
2
Indication

Nos

Feeder

HT side of
400/220KV
transformer

Nos

Nos

Nos

Bus
reactor

Bus
coupler

Bus transfer

LED Position indicator

for position Indicator
of earth switch
LED Position indicator
for Isolator position
Indicator of Red /
Green
Indicating
lamps
common DC Supply 1
/ 2 fail and ann. DC
fail
Push button common
DC supply 1 / 2 fail
and ann. DC fail
alarm accept
Bus
VT-1/VT-2
supply
healthy
Indicating
lamps
Red/yellow/blue
Transfer bus healthy
indication Lamp
Other Devices

Nos

Nos

Nos

Nos

Nos

Nos

Circuit label
Section of mimic
diagram
Internally
mounted
equipment
like
Heater with switch,

Nos
Set

2
1

2
1

2
1

2
1

2
1

Set

WBSETCL / TECH SPEC / Rev.-1

Page 78 of 104

Control & Relay Panel

Unit
Sl.
No.

d)

e)

f)

B.
1
2

5
7

Quantity

Particulars

thermostat,Cubicle
illumination
lamps,
power
Socket,
switches, fuses, link
etc. As described in
the main specification
One label indicating
manufacturers
Name,
P.O.
details,drg. ref. nos
etc.
Annunciation
windows,
lamps,
Accept/reset/test
push button etc. and
Associated relays if
the
annunciator
Relay is attached
with the windows
Common bell, hooter,
associated
Relays
etc. for annunciation
scheme
REAR PANEL:
Trip
circuit
supervision relay
Line CVT operated
under voltage Relay
for line side earth
switch interlock
Bus
VT
supply
selection
relaying
Scheme for metering
and protection Circuit
complete
in
all
respect
Auxiliary relays for
C.B
closing/
Tripping, if necessary
Circuit label
Internally
mounted
equipment
Like
heater with switch,
thermostat, Cubicle

WBSETCL / TECH SPEC / Rev.-1

Feeder

HT side of
400/220KV
transformer

Bus
reactor

Bus
coupler

Bus transfer

Set

Set

Set

Nos

Set

Set

Set

Nos
Set

2
1

2
1

2
1

2
1

2
1

Page 79 of 104

Control & Relay Panel

Unit
Sl.
No.

10

11

12
13

14
15

Quantity

Particulars

illumination
lamp,
power
Socket,
switch, fuse, links etc
as Described in main
specs
Timer
for
bus
selection incomplete
Alarm
Timer for discrepancy
alarm
of
Control
switch and CB
Flasher
relay
discrepancy condition
Of CB & its control
switch
Timer
for
bay
transfer
sequence
Incomplete alarm
CB
monitoring
auxiliary relays
Common DC supply
& aux. bus DC 1 & 2
supervision relay
AC operated accept
relay for above
AC supply supervision
relay

Feeder

HT side of
400/220KV
transformer

Bus
reactor

Bus
coupler

Bus transfer

Nos

Nos

Nos

Nos

As

As

As

As

As

Nos

reqd.
-

reqd.
-

reqd.
-

reqd.
4

reqd.
-

Nos

Nos

20.04 (B) 400KV SIMPLEX TYPE PROTECTION PANEL FOR TWO MAIN AND ONE
TRANSFER BUS AIS SYSTEM::
Sl.

Particulars

Unit

No.

Quantity
Feeder

HT

side

of

Bus reactor

Bus transfer

400/220KV
transformer
1

Main-1
numerical
distance protection
scheme
as
per
specification
Main-2
numerical
distance protection
scheme
as per

WBSETCL / TECH SPEC / Rev.-1

Set

Set

Page 80 of 104

Control & Relay Panel

Sl.

Particulars

Unit

No.

Quantity
Feeder

HT

side

of

Bus reactor

Bus transfer

400/220KV
transformer
2

7
8

10

11

12

specification
LBB Scheme with
carrier
tripping,
busbar
protection
and direct tripping
scheme
etc.from
remote
end.
(Preferably built in
Bus
Differential
relay)
DC
supervision
scheme relays for
M-1/Gr-A and M2/Gr.B protection
Over voltage protn
scheme
as
per
specification.
Transformer
differential
protection scheme
Circulatory current
protection relaying
scheme
REF protection
Backup directional
over current & earth
fault protection
Backup single step
impedance
protection scheme
Transformer/Bus
Reactor
internal
trouble
protection
scheme
Trip
relaying
scheme for M1/M2
of feeder GrA/Gr B
for
transformer/
Reactor etc. and
Trip
Relay
Supervision Relay
Over flux protection

WBSETCL / TECH SPEC / Rev.-1

Set

Set

Set

Set

Set

Set
Set

1
-

Set

Set

Set

Set

Page 81 of 104

Control & Relay Panel

Sl.

Particulars

Unit

No.

Quantity
Feeder

HT

side

of

Bus reactor

Bus transfer

400/220KV
transformer
13

Carrier
Switch

Selector

Nos

14

Distance
relay
setting
group
selector switch - 4
position

Nos

15

Test terminal block

Nos

20.04 (C) 400KV SIMPLEX TYPE CONTROL PANEL FOR ONE AND HALF BREAKER
SYSTEM:
Q u a n t i t y

Sl.
No.

Particulars

A.

CONTROL PANEL

1.

Metering Device

a)
b)

Ammeter
Voltmeter

Nos
Nos

c)
d)
e)
f)
g)

Nos
Nos
Nos
Nos
Nos

h)
i)

Watt meter with transducer

Varmeter with transducer
Provision for RWTI meter
Provision for ROTI meter
Wiring
for
intelligent
electronic
computer
compatible energy meter
(0.2 class)
Test Terminal Block
Voltmeter Selector Switch

j)

Frequency Meter

Nos

k)

Recording
voltmeter
(Digital)
Recording frequency meter
(Digital)
Remote
winding
temperature
Indicator
selector switch
Control Device

Nos

l)
m)

2.

WBSETCL / TECH SPEC / Rev.-1

Unit

Nos
Nos

Nos
Nos

Feeder Bay

Transformer Bay

Reactor Bay

Tie Bay

3
1+2(in any one
panel for bus)
1
1
1

3
1

3
1

1
1

1
1
1
1

1
1+2(in any one
panel for bus)
2(in any one
panel for bus)
2(in any one
panel for bus)
2(in any one
panel for bus)
-

1
1

1
1

Page 82 of 104

Control & Relay Panel

Sl.
No.
a)

b)
c)
d)

e)

f)

g)

h)

i)
3.
a)

b)
c)

d)
e)
f)
g)

g)

Q u a n t i t y
Particulars

Unit

Circuit Breaker Control

Switch, Discrepancy type
with built-in Indicator lamp
Isolator Control Switch
Earth
Isolator
Control
Switch
Line VT/ Bus VT selector
switch, 4 position, Line
VT Inter1 Inter2 Bus
VT
Synchronising
Selector
Switch
2 position
Multipin
Synchronising
Socket (with dummy plug
where necessary)
Discrepancy switch steady
lamp cut-off switch, 2position
DC supply selector switch,
3-position,
Supply-1/
Independent/ Supply-2
VT selector switch, 2
position, VT 1/ VT 2
Indication

Nos

LED Position Indicator for

Position indicator of Earth
Switch (ON/OFF)
LED Position Indicator of
Isolator
Indicating
lamp
for
incoming DC fail/ANN. Bus
DC fail
Indicating lamp for Bus PT
1&2 healthy
Circuit breaker Trip circuit
healthy indicating lamp
Trip circuit healthy Check
Push Button
C.B.
Spring
charge
indicating
lamp
where
necessary
Push Button for C.B. Spring
check, if required
WBSETCL / TECH SPEC / Rev.-1

Feeder Bay

Transformer Bay

Reactor Bay

Tie Bay

Nos

Nos

Nos

3+2(in any one

panel for Bus PT)
4+2(in any one
panel for Bus PT)
1

Nos

Set

Nos
1no in any one panel.
Nos
1no for each dia.
Nos

Nos

Nos

1no in any one panel.

4+2(in any one

panel for Bus PT)

3+2(in any one

panel for Bus PT)
As reqd.

As reqd.

As reqd.

Nos
1set for each Bus PT in any one panel

Set
Nos

Nos

Nos

Nos
Page 83 of 104

Control & Relay Panel

Q u a n t i t y

Sl.
No.

Particulars

4.

Other Devices

a)
b)
c)

Circuit Label
Section of Mimic Diagram
Internally
mounted
equipment like Heater with
Switch,
Thermostat,
Cubicle Illumination Lamps,
Power Socket, Switches,
Fuses,
Link
etc.
as
described in the main
specification
One
Label
Indicating
Manufacturers Name, P.O.
Details, Drg. Ref. Nos. etc.
Annunciation Windows as
reqd,
with
Lamps,
Accept/Reset/Test
Push
Button etc. and associated
Relays if the annunciator
relay is attached with the
windows

d)

e)

Unit

Feeder Bay

Transformer Bay

Nos
Set

Reactor Bay

Tie Bay

1no for each dia.

1no for each dia.

Set

1no for each dia.

Set

1no for each dia.

48

48

32

As reqd.

nos

20.04 (D) 400KV SIMPLEX TYPE RELAY PANEL FOR ONE AND HALF BREAKER SYSTEM:
Q u a n t i t y
Sl.
No.

Particulars

A.

RELAY PANEL:

a)

Auto Reclose Relay

b)

Auto-reclose
Selector
Switch (if necessary)
CB Trip circuit supervision
relay
Line CVT operated under
voltage Relay for line side
earth switch interlock
LBB Scheme with carrier
tripping, busbar protection
and direct tripping scheme
etc. from remote end.
(Preferably inbuilt in Bus
Differential relay)

c)
d)

e)

WBSETCL / TECH SPEC / Rev.-1

Unit

Feeder Bay

Transformer Bay

Reactor Bay

Tie Bay

Nos

Set

Set

Set

Page 84 of 104

Control & Relay Panel

Q u a n t i t y
Sl.
No.
f)

g)

h)

i)
j)

k)

l)

m)
n)

o)
p)

q)

Particulars

Unit

Bus VT supply selection

relaying
Scheme
for
metering and protection
Circuit complete in all
respect
Auxiliary relays for C.B
closing/
Tripping, if
necessary
Auxiliary
relay
for
multiplication
of
CB,
Isolator contacts
Circuit label
Internally
mounted
equipment Like heater with
switch, thermostat, Cubicle
illumination lamp, power
Socket, switch, fuse, links
etc as Described in main
specs
Timer
for
discrepancy
alarm of Control switch and
CB
Flasher relay discrepancy
condition Of CB & its
control switch
CB monitoring auxiliary
relays
GIS
compartment
monitoring Aux. relays
AC supply supervision relay
with test Push Button
Ann.
Bus
DC
supply
supervision relays with test
Push Button
DC supervision scheme
relays for M-1/Gr-A and M2/Gr.B protection with test
Push Button

Nos

WBSETCL / TECH SPEC / Rev.-1

Feeder Bay

Transformer Bay

Reactor Bay

Tie Bay

Set

Set

Set

As reqd.

As reqd.

As reqd.

Nos
Set

2
1

2
1

2
1

2
1

Nos

Nos
1set in any one panel
As Reqd.

As Reqd.

As Reqd.

As Reqd.

As Reqd.

As Reqd.

As Reqd.

As Reqd.

1set in any one panel

Nos
Set

1set in any one panel

2

Page 85 of 104

Control & Relay Panel

20.04 (E)

400KV SIMPLEX TYPE PROTECTION PANEL FOR ONE AND HALF BREAKER
SYSTEM:
Q u a n t I t y

Sl.
No.

Particulars

Unit

Feeder

Transformer

Reactor

2
1

Set

Set

Set

A. PROTECTION PANEL
a)
b)
c)

d)

e)

f)
g)
h)

i)
j)
k)

l)
m)

Carrier Selector Switch

Push Button for Trip Relay
Reset
Main I Tee Differential
Protection scheme with All
Equipment/relays, trip relays
with trip coil supervision relay
etc. as per specification
Main II Tee Differential
Protection scheme with All
Equipment/relays, trip relays
with trip coil supervision relay
etc. as per specification
Main-1 numerical distance
protection scheme as per
specification
Main-2 numerical distance
protection scheme as per
specification
Over voltage protn scheme
as per specification.
Differential
protection
relaying scheme as described
in the specification, complete
in all respect
Circulatory current protection
relaying scheme
REF protection
Back up directional O/C and
E/F IDMTL relaying scheme
with high set unit complete in
all respect with PT fuse
failure monitoring feature as
described in the specification.
Backup
single
step
impedance protection scheme
Transformer/ Bus Reactor
internal
trouble
auxiliary
relaying
scheme
for
Buchholz, winding temp. etc.
as per specification.

WBSETCL / TECH SPEC / Rev.-1

Nos
Nos
Set

Set

Set

Set

Set

Set

Set

Set

As reqd.

As reqd.

Page 86 of 104

Control & Relay Panel

Q u a n t I t y
Sl.
No.
n)

o)
p)
q)
r)

Particulars
Trip relaying scheme for
M1/M2 of feeder GrA/Gr B for
transformer/ Reactor etc. &
Trip Relay Supervision Relay
Over Flux Protection relaying
scheme
Test terminal block for
protective relays as required
Circuit label
Internally
mounted
equipment like heater with
switch, thermostat cubicle
illumination lamps, power
socket, switches, fuses, links
etc. as described in the main
specification

Unit

Feeder

Transformer

Reactor

Set

Nos

As reqd.

As reqd.

As reqd.

Nos

Set

Set

NB:
Items in case of incomplete diameter (D and I type layouts), control panel shall be equipped
fully as if the diameter is complete, unless otherwise specified. Annunciation relays shall also
be provided for the same and if required, necessary panel shall be supplied to accommodate
the same.
20.05 Bus Zone Protection for 400 & 220kV system:
All Equipment/relays, trip relays with trip coil supervision relay, Local Breaker Back-up
protection relay, CT Switching relay etc for all connected bays and bus extension bays with
the provision of future bays along with CPU & Bay unit for the bus bar protection scheme as
required for busbar protection as per Clause No. 16.21.01 & 16.21.02 shall be provided in one
set of separate simplex type panel.

21.00 DEVIATION:
Normally the offer should be as per technical specification without any deviation. For any
deviation in the tender quoted by the tenderer, the same shall be clearly indicated in the
deviation sheet, clause by clause, indicating reason and advantage for such deviation. Such
deviations may or may not be accepted. Deviation not indicated in the deviation sheet will not
be considered.

WBSETCL / TECH SPEC / Rev.-1

Page 87 of 104

Control & Relay Panel

22.00 RECOMMANDED SPARES:

A list of spares recommended by the bidder for ten years satisfactory performance along with
item wise unit price shall be furnished with the tender. The purchaser will decide the actual
quantity of spares to be ordered on the basis of the list and item wise prices quoted. This
shall not be taken into consideration for the purpose of evaluation of bid.

23.00 TENDER DRAWING, LITERATURE AND TEST CERTIFICATES BOTH FOR ROUTINE
TEST AND TYPE TEST:
Following drawings, literatures, filled up GTP and test certificates shall be submitted with the
tender for evaluation:
a)
b)
c)
d)
e)

Principal dimensioned details of each unit cubicle and complete assembly of panel board.
Front and rear views of the panel board with instrument and device positions marked.
Details of protection scheme of lines, transformers and other bays including annunciation,
monitoring, supervision etc. offered.
Literature describing the instruments, switches, relays and their characteristics, technical
details, relay setting calculation, operating manual etc.
Routine and type test certificates of all the protective relays carried out as per relevant IEC/
IS from a recognised laboratory shall be furnished. Performance certificate of all protective
relays from Power Utilities in India shall also be furnished.

24.00 CONTRACT DRAWING AND LITERATURE:

24.01 The following drawings in six (6) copies of each are to be submitted by the successful bidder
for approval of the purchaser before starting manufacturing of the same.
a)

Detailed dimensional drawings of control and relay panel including foundation drg. with cable
slots showing all equipment mounted on them along with complete panel wise list of
equipment and list of Name Plates. Weight of these panels with all the equipment mounted
on these shall also be furnished in the Drg.

b)

Contact development drawings of all switches, relays etc.

c)

Outlined drawings of internal wiring diagram of the instrument, relays, meters, annunciator
and other equipment showing external terminal connections with the equipment terminal
number.

d)

Complete AC and DC Schematic diagram of all panels of control and relay board to indicate
the followings:
i)
Annunciator circuit
ii)
Protection and control circuit
iii)
Indication and Supervision circuit
iv)
Synchronising circuit
v)
Other circuits as necessary
These drawings shall show AC power connection and Secondary connections for relays,
meters, terminal blocks with their number etc. interconnection diagram between control and

WBSETCL / TECH SPEC / Rev.-1

Page 88 of 104

Control & Relay Panel

relay board and circuit breaker, Power and Instrument Transformer and other equipment as
necessary.
24.02 After approval of above drawings ten sets of those drawings for each set complete set of C&R
board and wiring schedule including bus wire diagram for each panel are to be supplied by
the contractor.
One set of reproducible of the above drawings for each C&R board formation shall also be
supplied.
24.03 Six copies of the following literatures shall be supplied along with the approved drawings and
one
set of the same (soft copy) shall be supplied along with the drawing in the
first
submission:
a)

Literature describing construction, operation, adjustment and rating specification of all the
protective and auxiliary relays, recording instruments, metering instruments, control and
other switches, annunciators, fault locator, disturbance recorder and other equipments which
are used in the C&R panel.

b)

List of spare parts, identification number of renewable parts of relays, instruments, switches
and other equipments with the help of which the purchaser will be able to procure spare
parts from the contractor at any subsequent line.

c)

Commissioning, operating, maintenance instruction manual for each relay and equipment of
the panel.

25.00 TEST AT FACTORY:

The following tests shall be carried out and six (6) copies of test certificates along with test
result shall be supplied for approval.
a)
b)
c)
d)
e)

Visual checking of C&R panel.

Checking wiring of circuits and continuity.
One minute applied voltage test. All equipments on panel and wiring shall be tested for a
withstand voltage of 2 KV between different circuits shorted and earth.
Insulation resistance of the complete wiring, circuit by circuit with all equipment mounted on
the board before and after HV test.
Routine tests according to the relevant standards on the instruments, relays and other
devices.

26.00 INSPECTION/ TEST WITNESS:

a)

Tests shall be performed in presence of the purchaser's representative, if so desired by the

purchaser. The contractor shall give at least 21 (twenty one) days advance notice of the date
when the tests are to be carried out at manufacturers works.

b)

Relays and meters may be further tested at our testing laboratory. If any equipment is found
to be not in conformity with the specification by our testing engineers during testing, the
same shall be replaced by you at your cost immediately.

WBSETCL / TECH SPEC / Rev.-1

Page 89 of 104

Control & Relay Panel

GUARANTEED TECHNICAL PARTICULARS OF CONTROL & RELAY PANEL

(To be filled in and signed by the Bidder)

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

NAME OF THE EQUIPMENTS

A

CONTROL & RELAY PANELS

Name Of Manufacturer

Type and Designation

Conforming Standard

Type of sheet steel

Thickness of sheet steel

5.1

Front

5.2

Back

5.3

Sides

Details of Painting

Weight of each panel section

Overall dimensions of each panel section in

mm. (width x depth x height)

Total weight of all panels

10

Space required for installation of all panels

11

Details of Tropicalisation

12

Largest package for Transport

12.1

Gross weight

12.2

Overall dimensions

LED POSITION INDICATORS

Name Of Manufacturer

Type and Designation

Conforming Standard

Operating Voltage

TERMINAL BLOCK

Name Of Manufacturer

Type and Designation

Conforming Standard

No. of terminal studs per way

Rated current

WBSETCL / TECH SPEC / Rev.-1

Page 90 of 104

SUBMISSION

CONTROL & RELAY PANEL

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

Rated voltage

Materials used

7.1

Body

7.2

Terminal studs

7.3

Connecting links

7.4

Support springs

Minimum no. of conductors of area 2.5

sq.mm suitable for connection

8.1

All circuits except CT

8.2

CT Circuits

CONTROL SWITCHES

Name Of Manufacturer

Type and Designation

Conforming Standard

Type of Handle

No. of possible positions of handle with

diagrams

5.1

No. of contacts available

5.2

Maximum No. of contacts which can be

accommodated for each position

SUBMISSION

Rating of Contacts :

6.1

Voltage

6.2

Make and carry current continuously

6.3

Make and carry Current for 0.5 sec.

6.4

Break resistive load

6.5

Break inductive load

Whether locking arrangement provided

Mounting details

Dimensions

10

Other information, if any

INDICATING LAMPS

Name Of Manufacturer

Type and Designation

Conforming Standard

Ratings :

4.1

Current

4.2

Voltage

4.3

Wattage

WBSETCL / TECH SPEC / Rev.-1

Page 91 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

SUBMISSION

Colour of lamp

Permissible voltage variation

Whether series resistance is provided, if so

:

7.1

Ohmic value

7.2

Power loss

Life of lamp in burning hours

Other information, if any

PUSH BUTTONS

Name Of Manufacturer

Type and Designation

Conforming Standard

Contact type momentary / maintained

Whether integral
plates provided

No. of NO/NC contacts

ANNUNCIATORS

Name OF Manufacturer

Type and Designation

Conforming Standard

No. of windows

Dimensions of each Window (Length x

height x depth)

No. of lamps per window

Auxiliary supply voltage

Power Consumption

Details of auxiliary equipment such as

relays etc.

10

Required instantaneous making capacity of

initiating contacts

11

Type of reset-manual / self

12

Overall dimensions of annunciators

13

Particulars of wiring

14

Technical literature

15

Brief write-up of the scheme furnished

Built-in facility of DC Fail Annunciation
(Yes/No)

16

WBSETCL / TECH SPEC / Rev.-1

engraved

inspection

Page 92 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION
INDICATING METERS (Digital) (To be
furnished separately for each type of
meter)

Name Of Manufacturer

Type and Designation

Conforming Standard

Range :

4.1

Effective Range

4.2

Fiducial value

Whether CTR & PTR are Programmable

CT Ratio

PT Ratio

Accuracy class

Overall dimensions

10

Auxiliary Voltage (If required)

11

Display dimension

12

Display illumination

13

EMC

14

Measurement principal

15

Whether communicable

16

Response time

NUMERICAL TYPE DISTANCE RELAY

Name OF Manufacturer

Type and Designation

Conforming Standard (Whether IEC 61850

compliant)

Input Quantities

4.1

Rated AC Current & Maxm. Continuous AC

Current

4.2

Rated AC Voltage & Maxm. Continuous AC

Voltage

4.3

Rated DC Voltage

4.4

Tolerance Allowance in DC Voltage

4.5

Allowable Maxm. Ripple

SUBMISSION

Burden

5.1

C.T. Circuit

5.2

P.T. Circuit

5.3

D.C. Circuit :

WBSETCL / TECH SPEC / Rev.-1

Page 93 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

5.3.1

Operating (Maxm.)

5.3.2

Quiescent (Maxm.)

SUBMISSION

Thermal withstand rating (Current/Voltage)

6.1

For one sec.

6.2

For 0.5 sec

Frequency range for satisfactory operation

Characteristic on R - X plane

Number of zones provided

10

Setting ranges for distance measurement :

10.1

Zone 1

10.2

Zone 2

10.3

Zone 3

10.4

Any other zone

11

Timer setting ranges

11.1

Zone 2

11.2

Zone 3

11.3

Any other zone

12

Power swing blocking characteristics

13

Power swing blocking

13.1

Setting ranges

13.2

Whether
provided

13.3

Timer setting whether selectable or fixed

and its value

14
14.1
15
15.1
16

independent

zone

selection

V.T. Supply supervision

Method of detection
Switch on to fault feature
Method of detection
Whether scheme is suitable for autoreclose

16.1

Single phase

16.2

Three phase

16.3

Whether check synchronising relay and

deadline charging relay is in-built with the
distance relay

17

Whether scheme is suitable for carrier

aided tripping scheme

18

Directional O/C & earth fault element

WBSETCL / TECH SPEC / Rev.-1

Page 94 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

18.1

Whether provided as in-built of numerical

distance relay:

18.2

Its setting range

18.3

Whether contact for carrier inter tripping

from the DEF relay is provided

19

Accuracy :

19.1

Zone 1 reach

19.2

Zone 2 reach

19.3

Zone 3 reach

19.4

Zone timer unit

19.5

Angular reach

20

SUBMISSION

Operating time for fault at 50% of zone 1

set with CVT on line side and with :

20.1

SIR = 4

20.2

SIR = 15

21

Accuracy due to variation of frequency (+/5%)

22

Setting range of residual compensation

23

Trip contact ratings

23.1

Make and carry continuously

23.2

Make and carry for 0.5 sec.

23.3

Break :

23.3.1

Resistive load

23.3.2

Inductive load (with L/R = 40)

24

No. of B/Is & B/Os

25

Details of Man Machine interface both for

local and remote control and monitoring
provided such as serial communication
protocol, communication speed, LAN
compatible, type of connectors etc.

26

Additional functions provided in the relay

which are not specified in the specification
AUTO
RECLOSE
RELAY
(Built-in
feature of Numerical Distance Relay)

Suitable for single and three phase auto reclosing.

Single phase dead time setting range

Three phase dead time setting range

Reclaim time setting range

WBSETCL / TECH SPEC / Rev.-1

Page 95 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

SUBMISSION

Whether check synchronising and dead line

charging relays included as a part of the
auto reclose scheme

Whether four position selector switch is

included ?

Whether single shot?

FAULT LOCATORS (Built-in feature of
Numerical Distance Relay)

Triggering Method

Rate of sampling per cycle

A/D converter bit resolution

Whether
following
fault
provided in displaying unit

4.1

information

Distance to fault location reach in Km

4.1.1

Resistive detection

4.1.2

Reactive detection

4.2

Faulted Phase

4.3

Time of Fault

4.4

Date of Fault

Whether mutual compensation of D/C line

provided

Maximum registering time

Whether direct display unit provided ? If

so, details to be given

Accuracy

NUMERICAL
TRANSFORMER
DIFFERENTIAL RELAYS

Name of Manufacturer

Type and Designation

Conforming Standard (Whether IEC 61850

compliant)

Current Rating

Operating setting range

Bias setting range

No. of B/Is & B/Os

Whether ICT required

Display

WBSETCL / TECH SPEC / Rev.-1

Page 96 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

10

Detail of Man-machine Interface both for

Local & Remote control and monitoring
provided

11

Speed of Operation of Relay

12

Setting of instantaneous element

13

Type and scheme for second and fifth

harmonic restrain

14

Contact rating :

14.1

Make and carry continuously

14.2

Make and carry for 0.5 sec.

14.3

Break :

14.3.1

Resistive load

14.3.2

Inductive
constant

load

with

40

SUBMISSION

millisec

time

15

Additional function & feature provided in

the Relay which are not specified in the
specification

TRANSFORMER OVERFLUXING RELAY

Name of Manufacturer

Type and Designation

Conforming Standard

Rated voltage and frequency

Rated DC voltage

Solid state or Electro mechanical

Thermal Withstand Rating

Number of Contacts

8.1

Normally open

8.2

Normally closed

Contacts - Self reset

10

Rated Burden at highest and lowest tap

11

Operating indicator provided ?

12

Contact Ratings :

12.1

Make and carry continuously

12.2

Make and carry for 0.5 sec.

12.3

Break

12.3.1

Resistive Load

12.3.2

Inductive Load (with L/R = 40)

13

Setting ranges :

WBSETCL / TECH SPEC / Rev.-1

Page 97 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

13.1

V/F

13.2

Time for alarm

13.3

Time for tripping

SUBMISSION

NUMERICAL OVERCURRENT & EARTH

FAULT RELAYS - NON-DIRECTIONAL /
DIRECTIONAL :

Name of Manufacturer

Type and Designation

Conforming Standard (Whether IEC 61850

compliant)

Rated current

Rated AC voltage (Directional Relay only)

Rated DC voltage

Operating Principle

Thermal Withstand Rating

Number of B/Is & B/Os

10

Contacts Latched/Unlatched/Programmable

11

Burden

12

Operation indicator provided ?

13

Contact Ratings

13.1

Make and carry continuously

13.2

Make and carry for 0.5 sec.

13.3

Break :

13.3.1

Resistive Load

13.3.2

Inductive Load (with L/R = 40)

14

Operating characteristics

15

Current unit setting range

15.1

Inverse time

15.2

High set inst. unit

16

Characteristic angle for Directional Relay

Additional features applicable

numerical relays only

Whether self supervision and diagnostic

feature available

WBSETCL / TECH SPEC / Rev.-1

Page 98 of 104

for

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

Whether potential free change over contact

for annunciation in the event of internal
failure

Whether password protection available for

setting change etc.

Number of
available

Whether LED indication available for visual

annunciation of different types of faults

Current and time setting range & steps

Whether separate IVT is required for

derivation of zero sequence voltage in
Directional relays

binary

inputs

SUBMISSION

&

outputs

DISTURBANCE RECORDERS (Built-in

feature of Numerical Distance Relay)
1

Number of channels provided for analog

recording

Number of channels provided for event

recording

Time of recording prior to event

Duration of recording after the event

By how many nos. can the channels be

expanded :

5.1

Analog Channel

5.2

Event Channel

Whether all starting sensor Provided?

Linearity Error

Memory :

8.1

Pre fault in ms

8.2

Post fault in sec.

Frequency Response

10

Resolution of the event channel (ms)

11

Resolution :

11.1

Time

11.2

Amplitude

12.1

Whether facility provided for downloading

of station identification code along with
date & time

WBSETCL / TECH SPEC / Rev.-1

Page 99 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

12.2

If yes mention the programmable character

length (nos.) available

13

Details of arrangements for date & time

marking

SUBMISSION

RESTRICTED EARTH FAULT RELAY /

CIRCULATING EARTH FAULT
PROTECTION

Name of Manufacturer

Type and Designation

Conforming Standard

Rated current

Rated DC voltage

Operating principle

Solid state or Electro mechanical

Thermal Withstand Rating

Number of Contacts and ratings

10

Contacts - Self reset/hand reset

11

Burden

12

Operation indicator provided ?

13

Contact Ratings

13.1

Make and carry continuously

13.2

Make and carry for 0.5 sec.

13.3

Break

13.3.1

Resistive Load

13.3.2

Inductive Load (with L/R = 40)

14

Setting range

15

Operating Time

16

Whether tuned to system frequency

17

Value of stabilising resistor

18

Particulars of non-linear resistor

NUMERICAL BUS BAR PROTECTION

SCHEME

Name of Manufacturer

Type and Designation

Conforming Standard (Whether IEC 61850

compliant)

Rated current

Rated DC voltage

WBSETCL / TECH SPEC / Rev.-1

Page 100 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

Operating
principle
(Distributed
architecture or Central architecture)

Maximum no of bays can be incorporated

in the scheme

Suitable for 2 Main & 1 Transfer bus or not

Operation

Impedance:

10

% Biasing

11

Thermal Withstand Rating

12

Number of Contacts :

12.1

Normally open

12.2

Normally closed

Low

impedance/High

13

Contacts - Self reset

14

Burden

15

Operation indicator provided ?

16

Contact Ratings :

16.1

Make and carry continuously

16.2

Make and carry for 0.5 sec.

16.3

Break :

16.3.1

Resistive Load

16.3.2

Inductive Load (with L/R = 40)

17

Operating time

18

Setting ranges

19

Transient free in operation ?

20

Particulars of end zone protection

21

Particulars of CT secondary open circuit

protection

22

Does the scheme give 100% security and

reliability during all system operating
conditions

23

Through fault stability

CIRCUIT BREAKER FAILURE RELAY

Name of Manufacturer

Type and Designation

Conforming Standard

Rated current

Rated DC voltage

Operating principle

WBSETCL / TECH SPEC / Rev.-1

SUBMISSION

Page 101 of 104

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

Solid state or Electro mechanical

Thermal Withstand Rating

Number of Contacts :

9.1

Normally open

9.2

Normally closed

10

Burden

11

Operation indicator provided ?

12

Contact Ratings :

12.1

Make and carry continuously

12.2

Make and carry for 0.5 sec.

12.3

Break :

12.3.1

Resistive Load

12.3.2

Inductive Load (with L/R = 40)

13

Operating time

14

Resetting time

15

Setting range :

15.1

Current

15.2

Time

TRIP CIRCUIT SUPERVISION RELAY

Name of Manufacturer

Type and Designation

Conforming Standard

Rated DC voltage

Operating principle

Electro mechanical

Thermal Withstand Rating

Number of Contacts :

8.1

Normally open

8.2

Normally closed

Contacts - self reset

10

Burden

11

Operation indicator provided ?

12

Contact Ratings :

12.1

Make and carry continuously

12.2

Make and carry for 0.5 sec.

12.3

Break :

12.3.1

Resistive Load

12.3.2

Inductive Load (with L/R = 40)

WBSETCL / TECH SPEC / Rev.-1

Page 102 of 104

SUBMISSION

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL

DESCRIPTION

13

Whether pre-closing and

supervision provided ?

14

Time delay

UNIVERSAL
AND VTs :

Name of Manufacturer

Type and Designation

Conforming Standard

Ratio

Rated output VA

Class of accuracy

Short time rating :

7.1

Current

7.2

Voltage

TYPE

SUBMISSION
post

AUXILIARY

Knee point voltage for Class `PS'

Excitation current for Class `PS'

9.1

KPV

9.2

50 Percent KPV

10

Internal resistance of

10.1

Primary

10.2

Secondary

11

Temperature rise

12

Mounting details

13

Overall dimensions

14

Any other details

MASTER TRIP RELAY

Name of Manufacturer

Type and Designation

Conforming Standard

Rated DC voltage

Electro mechanical

Whether Electrical Reset (Yes/No)

Thermal Withstand Rating

Number of Contacts :

8.1

Self Reset

8.2

Hand Reset

Burden

10

Operation indicator provided ?

WBSETCL / TECH SPEC / Rev.-1

closing

Page 103 of 104

CTs

Control & Relay Panel

SUBMISION OF GTP AGAINST LOA REF:

<TO BE FILLED BY THE BIDDER>

NAME OF THE BIDDER

<TO BE FILLED BY THE BIDDER>

SL
11

DESCRIPTION
Contact Ratings :

11.1

Make and carry continuously

11.2

Make and carry for 0.5 sec.

11.3

Break :

11.3.1

Resistive Load

11.3.2

Inductive Load (with L/R = 40)

12

Operating Time

OVER VOLTAGE RELAY

Name of Manufacturer

Type and Designation

Conforming Standard

Rated Auxuliary DC voltage

Solid state or Electro mechanical

Rated AC Voltage & Frequency

Setting Range (Voltage & Time)

7.1

for First Stage

7.2

for Second Stage

Drop-Off to Pick-Up ratio

Burden

10

Operation indicator provided ?

11

No. of Output Contacts for each Phase

12

Contact Ratings :

12.1

Make and carry continuously

12.2

Make and carry for 0.5 sec.

12.3
12.3.1
12.3.2

SUBMISSION

Break :
Resistive Load
Inductive Load (with L/R = 40)

WBSETCL / TECH SPEC / Rev.-1

Page 104 of 104

Control & Relay Panel