Storage

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 9

STORAGE

Rule 1090: Hazardous Materials:


1095.01 : Vats and Tanks:
(1) Vats, pans, and open tanks containing hot corrosive or toxic liquids shall, when
the opening or top is less than 1 m (3.3 ft) above the floor or working level, be
either:
a. raised so the top will not be less than 1 m(3.3 ft.) from the floor or working
level, or
b. guarded on all sides by enclosures or by standard railings and when the
top is less than 15 cm.
(6 in.) above the floor shall be provided with standard toeboards.
The provisions of a. and b. shall apply to every vat, pan or tank irrespective of the
nature of the liquid it may contain.
(2) Where vats, pans or open tanks containing hot, corrosive or toxic liquids adjoin,
the space shall be fenced.
(3) Vats, pans, or open tanks containing hot, corrosive or toxic liquids shall be
provided with pipes or drains of sufficient capacity to carry off the contents without
spilling or their backing up on the floor.
(4) Above-ground tanks containing hot, corrosive or poisonous liquids shall be:
a. surrounded by pits, catch basins or depressions of sufficient size to hold
the entire contents in
case of rupture; and
b. provided with overflow pipes leading to tanks or to safe places outside the
building.
(5) Walkways shall not cross over open vats, pans or tanks containing hot, corrosive
or toxic liquids. Where it is necessary to install service walkways for access to
agitator drives or valves or for taking samples, such walkways shall be:
a. not less than 50 cm (20 in.) in width;
b. provided on both sides with standard railings and toeboards; and
c. kept clean and dry at all times.
1095.02 : Storage Tanks for Non-Flammable Hazardous Liquids:
(1) Tanks used for storage of non-flammable hazardous liquids shall be:
a. located above ground or floor level;
b. supported so that leakage from any part of the tank will be noticeable;
c. surrounded with pits, catch basins or depressions of sufficient size to hold
the entire contents
of the largest tank in the event of rupture;

d. covered with protective paint to prevent corrosion from moisture or fumes;


and
e. provided with stairways or permanent ladders and platforms, where
necessary, for
convenient and safe access to all parts of the tank and with
floors or platforms preferably of metal grating.
(2) Tanks used for storing non-flammable hazardous liquids shall not be placed
above passageways.
(3) Tanks used for storing non-flammable hazardous liquids stored in pits below
ground level:
a. the pits shall be of concrete or masonry with sufficient space between the
walls and the tanks
to permit the passage of any person at any point; and
b. the tanks shall be mounted 38 to 45 cm. (15 to 18 in.) above the bottom of
the pit.
(4) Pits containing sunken tanks used for storing non-flammable hazardous liquids
shall be provided with covers and fixed ladders for safe access.
(5) All control-valves for sunken tanks used for storing non-flammable hazardous
liquids shall be:
a. situated or of such design that they can be turned without any person
entering the pit; and
b. provided with locking devices operated from the outlets of the pit.
(6) Workers entering storage tanks and pits containing hazardous liquids shall be
provided with personal protective clothing and equipment conforming to the
requirements of Rule 1080.
(7) Tanks used for storing corrosive or caustic liquids shall be provided with:
a. a permanent open wet pipe not less than 5 cm. (2 in.) in diameter at the
highest point in the
tank; and
b. a drain connection at the lowest point in the tank discharging into a safe
place.
(8) Tanks used for storing corrosive or caustic liquids shall have the filling
connections at the top and the discharge pipes 15 cm. (6 in.) above the bottom.
1095.03 :
Drums containing acids shall be stored in cool places with the bung up. They shall
be carefully opened each time the drum has been moved or once a week if stored
for a period of time to relieve any internal pressure and subsequently sealed again.
1095.04 : Carboys for Acids:

(1) Carboys containing acids shall be encased singly in baskets or in boxes


cushioned with noncombustible packing material.
(2) Carboys containing acids shall be stored in separate store rooms or buildings
with concrete floors having anti-acid protection or with brick floors properly drained
to catch basins, dry and protected from dampness, extreme heat or sudden change
in temperature.
(3) Carboys containing acids shall not be piled one on top of another but should be
placed in suitable storage racks or on wooden strips laid on the floor.
(4) Special handling equipment such as two-wheeled carboy trucks shall be
provided for transporting carboys containing acids to and from storage.
(5) Adequate equipment shall be provided and used for the emptying of carboys.
(6) Empty acid carboys shall be stored apart from filled carboys.
(7) Empty carboys shall be thoroughly washed out by turning them upside down
over and upward with stream of water and drained before they are stored.
(8) Carboys together with their baskets or boxes shall be examined as to their
condition before they are filled with acid.
1096.03: Storage and Handling:
Stocks of lead materials shall be kept in special storage rooms outside the workrooms. Workrooms in
which lead materials are handled shall be located in relation to other parts of the shop of factory in as
small an area as possible to confine the lead and to concentrate control measures in that area.
Rule 1140: Explosives
1146 : Storage of Explosives:
1146.01: Class I Explosives:
Class I magazines shall be those containing over 22.5 kgs. (50 lbs.) of explosives. Such magazines
shall have no openings except for ventilation and entrance. It shall be of masonry or metal
construction or a combination of both constructed and maintained as follows:
(1) Doors - Doors must be kept closed and securely locked at all times except when opened for the
purpose of storing or removing explosives or to allow persons authorized to enter such magazines.
(2) Signs - The premises on which explosives are kept or stored must be conspicuously defined and
marked by appropriate signs, such as, EXPLOSIVE KEEP OFF, legibly printed thereon in letters not
less than 15 cm. (6 in.) high. Such signs must not be placed on magazines but shall be so located that
a bullets passing through the sign will not strike the magazine.
(3) Wood - The outside walls shall be of 5 cm. x 10 cm. (2 in. x 4 in.) studding with a 5 cm.

(2 in.) plank or tongued and grooved lumber having a nominal size of 2.5 cm. (1 in.) covered with not
less than No. 26 gauge galvanized iron or steel on the outside. The inside walls shall be lined with
tongued and grooved reefers. The space between the outer and inner walls shall be filled with dry
course sand (not crushed stone or gravel) or a weak mixture of cement mortar. All lumber used shall
be well seasoned and free from loose knots, bark edges or decay.
(4) Brick - Brick walls shall be 20 cm. (8 in.) in thickness of medium soft variety laid in cement mortar
containing not over 25% lime.
(5) Concrete - Concrete walls shall be 15 cm. (6 in.) in thickness constructed of nine (9) parts sand to
one (1) part cement with a 1.25 cm (1/2 in.) face surface of three (3) parts sand to one (1) part
cement.
(6) Cement Block - Cement block walls shall be 20 cm. (8 in.) thick hollow cement block, a mixture of
seven (7) parts sand and one (1) part cement. The spaces in the block shall be filled with dry coarse
sand (not crushed stone or gravel) or a weak mixture of cement mortar.
(7) Fabricated Metal - Walls and roof shall consist of approximately No. 14 gauge metal securely
fastened together. Walls shall be lined with 10 cm. (4 in.) of brick of at least a 15 cm. (6 in) sand fill
between the interior and exterior walls.
(8) Lining of Magazines - Lining of magazines as specified in paragraphs (3) and (7) above, may not be
required for the storage of black powder or for the storage of not more than 100,000 pieces of blasting
caps.
(9) Foundation - The foundation shall be of stone laid in concrete, wood posts or brick piers. Magazines
of less than 13,600 kgs. (30,000 lbs.) capacity shall have flooring of lumber having a nominal size of
2.5 cm. (1 in.) tongued and grooved. Magazines of larger capacity shall have double flooring.
(10) Ventilation - The floor and ceiling shall be constructed to within 5 cm. (2 in.) of the walls to provide
a 3 cm. ventilation space. This shall be provided by constructing a 2.5 cm. x 15 cm. (1 in. x 6 in.)
lattice wood lining on 5 cm. x 5 cm. (2 in. x 2 in.) wood stud 60 cm. (2 ft.) on centers. Foundation
ventilators shall be spaced not more than 150 cm. (5 ft.) on center in all sides and properly screened to
prevent the entrance of sparks of fire.
(11) Nails - All heads of nails shall be countersunk. No spark producing metal shall be exposed inside
the buildings.
(12) Doors - The doors shall be 1 m. (3.28 ft.) wide and 1.8 m. (6 ft.) high constructed of at least three
(3) layers of hard wood, having a nominal size of 2.5 cm. (1 in.) and covered on the outside with a steel

sheet of at least No. 20 gauge. Where there is a need for bullet proofing the thickness of the steel
sheet shall be a minimum of 1 cm. (3/8 in.).
(13) Roof - Except where permission for other construction is approved, a bullet-proof sand roof shall
be used constructed as follows:
Form a box by laying a floor of a good grade of tongue and groove boards on ceiling joists and
build a 2.5

cm. x 10 cm. (1 x 4 in.) rim lined with one (1) layer of building paper and filled with 10

cm.
(4 in.) of dry coarse sand. Except for fabricated metal magazines, the outer roof shall be
covered with not

less than No. 26 gauge galvanized iron ridge roll fastened to 2.2 cm (7/8 in.)

sheating.
(14) Gutters and Down Spouts - Where water may enter through the door, gutters and down spouts
shall be provided on the door sides.
(15) Materials and Workmanship - Only superior materials and workmanship shall be used.

1146.02: Class II Magazines:


Class II magazines shall be used for storing not more than 22.5 kgs (50 lbs.) of explosives. It shall be of
wood or metal construction or a combination of both.
(1) Construction - The principle of construction is simply that of placing one box inside of another with
a 12.5 cm. (5 in.) space in between filled with dry coarse sand, not gravel or crushed rock.
(2) Outer Box - The outer box shall be constructed of tongued and grooved lumber having a nominal
size of 2.5 cm. (1 in.) plain lumber. The outside of the box shall be covered with no less than No. 24
gauge iron sheet. The outer box shall be 0.33 m. (1 foot) longer, 0.33 m. (1 foot) wider, and 15 cm (6
in.) deeper than the inner box allowing a 12.5 cm. (5 in.) space on all sides for sand filling. The inner
box shall be set inside the outer box with the tops at level with each other and fastened into place.
(3) Inner box - The inside of all boxes shall be surfaced. No nail, bolt or metal screw heads shall be
exposed on the inside of the box.
(4) Ventilation - At the top of each box, on the sides and ends, cut 0.625 cm (1/4 in.) by 5 cm. (2 in.)
notches, spaced about 0.33 m. (1 foot) apart, and not directly opposite.
(5) Setting - The box (magazine) shall be set in a level position and supported by either wooden sills,
bricks or piers and the bottom of the magazine kept at about 15 cm. (6 in.) off the ground.

(6) Sand Fill - Fill the space between boxes with dry coarse sand (not gravel or crushed rock) to within
0.625 cm (1/4 in.) of the top. To prevent sand from falling into the storage space, a cover may be
placed over the sand space.
(7) Locks - magazines shall be provided with adequate locks.
(8) Signs - At each end and on top of the magazine, above the side wall and on its barricades, there
shall be conspicuously posted at all times appropriate, signs, such as, MAGAZINE-EXPLOSIVEDANGEROUS legibly printed in letters not less than 15 cm. (6 in.) high.
1146.03: Temporary Storage At Job Sites:
(1) When used for temporary storage at a job site for blasting operations, Class II magazines shall be
located away from neighboring buildings, railways, highways and other magazines. A distance of at
least 45 m. (150 ft.) shall be maintained between Class II Magazines and the work site when the
quantity of explosives kept therein is in excess of 11.4 kgs. (25 lbs.) and at least 15 m. (50 ft.) when
the quantity of explosives is 11.4 kgs (25 lbs.) or less. The enforcing authority may require greater
separation between Class II magazines and the work site where conditions warrant.
(2) Class II portable magazines for transporting small amounts of explosives from the permanent
magazine to the work site and for temporary storage in the work site shall be constructed or built of 5
cm. (2 in.) hardwood or 7.5cm. (3 in.) soft wood, well braced at corners, with sheet metal exterior
sheating.

Rule 1170: Unfired Pressure Vessels


(1) Cylinders shall be adequately protected against excessive variations of temperature, direct rays of
the sun and continuous dampness.
(2) Storage of charged cylinders inside factory buildings shall be:
a. limited to such number as to be reasonably safe for the workers therein:
b. suitably placed and secured against their falling and rolling.
(3) Storage rooms containing charged cylinders should be appropriately marked on the outside with
clearly visible danger signs.
(4) Cylinders shall be segregated for storage by type of gas and empty cylinders shall be stored apart
from charged cylinders.
(5) Cylinders shall not be placed:

a. in or near gangways, stairways, elevator installations or other places where moving objects
may strike or fall against them.
b. close to highly flammable substances; and
c. adjacent to air intake;
d. basement or cellar
(5) Cylinders shall not be placed:
a. in or near gangways, stairways, elevator installations or other places

where moving

objects may strike or fall against them.


b. close to highly flammable substances; and
c. adjacent to air intake;
d. basement or cellar
(6) Storerooms shall:
a. be provided with adequate ventilation facilities to the outside air; and
b. have an adequate number of exits having regard to the quantity and nature of the gas
stored.
(7) Smoking in cylinder rooms is prohibited.
Rule 1410: Construction Safety:
1412.14 : Storage of Materials:
(1) Building materials and equipment shall not be placed or stored on a permanent or temporary
structure exceeding its safe load carrying capacity.
(2) Lumber structural steel and similar building materials shall be properly stored and secured against
collapsing or tipping. Cross pieces shall be used in a pile of lumber more than 1 m. (3 ft.) high.
(3) Pipes and reinforcing steels shall be stacked in racks or frames supported to prevent movement.
(4) Gangways and platforms shall not be used as storage for materials and tools.
1412.15 : Storage of Cylinders:
Compressed gas cylinders shall be stored in upright position protected against heat and overturning
and when not in use, the control valves shall be covered by protective caps screwed to proper
positions.
Rule 1940: Fire Protection and Control
(1) Significant quantities of commodities with fire hazards greater than ordinary combustible
commodities shall be separated from the main bulk by fire walls.

(2) Commodities which may be hazardous when combined with each other shall be stored separately
to prevent contact with each other.
(3) Water absorbed during fire fighting operations shall be considered in the determination of safe floor
loads.
Tank Storage:
(1) Tanks used for flammable and combustible liquids shall be built of steel.
(2) Tanks may be built of materials other than steel for underground installation or if required by the
properties of the liquid stored shall be designed to specifications approved for the purpose.
(3) Unlined concrete tanks may be used for storing flammable or combustible liquids having a gravity
of 40 degrees or heavier.
(4) Tanks located above ground or inside buildings shall be of non-combustible construction.
Rule 1950: Pesticides and Fertilizers
STORAGE OF PESTICIDES
(1) Pesticides shall be stored in original container tightly closed.
(2) The precaution listed in the label shall be followed for the storage of each compound.
(3) Pesticides shall be stored in cool, dry, and well ventilated places not accessible to children, animals
and unauthorized persons.
(4) Pesticides shall be stored away from food and foodstuff.
(5) Volatile pesticides shall always be stored separately from other pesticides to avoid cross
contamination and shall always be stored in an unrestricted atmosphere.
(6) Smoking, eating or drinking in the pesticides area is prohibited.
STORAGE OF FERTILIZERS
(1) Storage place for fertilizers shall be well lighted to facilitate easy identification of chemicals.
(2) Storage building shall be sound, weather-proof, water-tight and fire-resistant.
(3) Storage rooms or buildings shall be locked to prevent entry of unauthorized persons or animals.
(4) Fertilizers shall be stored separately from other material and in particular; away from food and
feeding stuff.
(5) Fertilizers of different kinds shall be stored separately in sacks or containers on skids or platform
and kept away from walls and combustible materials.
(6) Transfer nitrate from bags and wooden barrels to incombustible bins. Empty bags and barrels shall
be thoroughly washed after each use.

(7) Sodium chloride shall be stored in metal containers.


(8) Aqua ammonia shall be stored in a cast iron or mild steel tank designed with a working pressure of
7 kg./cm2
(9) Anhydrous ammonia shall be transported and stored in pressure containers designed with a
working pressure of 18.65 kg,/cm2 g (265 psig). Storage tanks shall have no brass and copper fittings.
(10) Anhydrous ammonia tanks shall be provided with pressure relief valves on the pipelines and bleed
valves in the hoses.
(11) Tanks for anhydrous ammonia shall:
a. be situated at a safe distance from other buildings, fire hazard and traffic;
b. be protected against solar heat and mechanical damage; and
c. not more than four-fifths (4/5) full.
(12) Organic fertilizer shall be stored in open and well ventilated areas.
(13) Fertilizers stored in containers other than those provided by the manufacturer shall be clearly
labeled with the name of the substance and marked with proper symbols.

You might also like