MICROWAVE OVEN

MO1650WA
MO1650BA
MO1650CA

SERVICE
MICROWAVE OVEN

Manual
CONTENTS

1. Precaution
2. Specifications
3. Operating Instructions
4. Disassembly and Reassembly
5. Alignment and Adjustments
6. Trouble shooting
7. Exploded Views and Parts List
8. PCB Diagrams
9. Schematic Diagrams

SEA

PRECAUTIONS TO BE OBSERVED BEFORE AND

DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be
operated with the door open.
(b) Make the following safety checks on
all ovens to be serviced before activating
the magnetron or other microwave
source, and make repairs as necessary:
(1) Interlock operation,
(2) proper door closing,
(3) seal and sealing surfaces (arcing,
wear, and other damage),
(4) damage to or loosening of hinges
and latches,
(5) evidence of dropping or abuse.

(c) Before turning on microwave power

for any service test or inspection within
the microwave generating
compartments, check the magnetron,
wave guide or transmission line, and
cavity for proper alignment, integrity,
and connections.
(d) Any defective or misadjusted
components in the interlock, monitor,
door seal, and microwave generation
and transmission systems shall be
repaired, replaced, or adjusted by
procedures described in this manual
before the oven is released to the
owner.
(e) A Microwave leakage check to verify
compliance with the Federal
performance standard should be
performed on each oven prior to
release to the owner.

1. Precaution
Follow these special safety precautions. Although the microwave oven is completely safe during ordinary use,
repair work can be extremely hazardous due to possible exposure to microwave radiation, as well as potentially
lethal high voltages and currents.

1-1 Safety precautions (

)
10. Service technicians should remove their
watches while repairing an MWO.

1. All repairs should be done in accordance

with the procedures described in this
manual. This product complies with
Federal Performance Standard 21 CFR
Subchapter J(DHHS).

11. To avoid any possible radiation hazard,

replace parts in accordance with the wiring
diagram. Also, use only the exact
replacements for the following parts:
Primary and secondary interlock switches,
interlock monitor switch.

2. Microwave emission check should be performed

to prior to servicing if the oven is operative.
3. If the oven operates with the door open :
Instruct the user not to operate the oven and
contact the manufacturer and the center for
devices and radiological health immediately.

12. If the fuse is blown by the Interlock Monitor

Switch: Replace all of the following at the
same time: Primary, door sensing switch
and power relay, as well as the Interlock
Monitor Switch. The correct adjustment of
these switches is described elsewhere in
this manual. Make sure that the fuse has the
correct rating for the particular model being
repaired.

4. Notify the Central Service Center if the

microwave leakage exceeds 5 mW/cm2.
5. Check all grounds.

13. Design Alteration Warning:

Use exact replacement parts only, i.e.,
only those that are specified in the
drawings and parts lists of this manual.
This is especially important for the
Interlock switches, described above.
Never alter or add to the mechanical or
electrical design of the MWO. Any design
changes or additions will void the
manufacturer's warranty. Always unplug
the unit's AC power cord from the AC
power source before attempting to
remove or reinstall any component or
assembly.

6. Do not power the MWO from a "2-prong"

AC cord. Be sure that all of the built-in
protective devices are replaced. Restore any
missing protective shields.
7. When reinstalling the chassis and its
assemblies, be sure to restore all protective
devices, including: nonmetallic control
knobs and compartment covers.
8. Make sure that there are no cabinet openings
through which people --particularly
children --might insert objects and contact
dangerous voltages. Examples: Lamp hole,
ventilation slots.

14. Never defeat any of the B+ voltage

interlocks. Do not apply AC power to the
unit (or any of its assemblies) unless all
solid-state heat sinks are correctly installed.

9. Inform the manufacturer of any oven found

to have emission in excess of 5 mW/cm2,
Make repairs to bring the unit into
compliance at no cost to owner and try to
determine cause.
Instruct owner not to use oven until it has
been brought into compliance.

15. Some semiconductor ("solid state") devices

are easily damaged by static electricity.
Such components are called
Electrostatically Sensitive Devices (ESDs).
Examples include integrated circuits and
field -effect transistors.

Samsung Electronics America, Inc.

Headquarters 105 Challenger Road
Ridge field Pack, New Jersey 07660-0511

Immediately before handling any

semiconductor components or assemblies,
drain the electrostatic charge from your
body by touching a known earth ground.

- 1 -

1-2 Special Servicing Precautions (Continued)

19. Use replacement components that have the
same ratings, especially for flame resistance
and dielectric strength specifications. A
replacement part that does not have the
same safety characteristics as the original
might create shock, fire or other hazards.

16. Always connect a test instrument's ground

lead to the instrument chassis ground before
connecting the positive lead; always remove
the instrument's ground lead last.
17. When checking the continuity of the witches
or transformer, always make sure that the
power is OFF, and one of the lead wires is
disconnected.
18. Components that are critical for safety are
indicated in the circuit diagram by
shading,
or
.

1-3 Special High Voltage Precautions

1. High Voltage Warning !
Do not attempt to measure any of the high
voltages --this includes the filament voltage
of the magnetron. High voltage is present
during any cook cycle.

High Voltage Capacitor

Before touching any components or wiring,

always unplug the oven and discharge the
high voltage capacitor (See Figure 1-1)
2. The high-voltage capacitor remains charged
about 30 seconds after disconnection. Short
the negative terminal of the high-voltage
capacitor to the oven chassis. (Use a
screwdriver.)
3. High voltage is maintained within specified
limits by close-tolerance, safety-related
components and adjustments. If the high
voltage exceeds the specified limits, check
each of the special components.

Fig. 1-1 Discharging High Voltage Capacitor

PRECAUTION

PRECAUTION

Never touch any circuit wiring with your hand

nor with insulated tool during operation.

There exists HIGH VOLTAGE ELECTRICITY

with high current capabilities in the circuits of the
HIGH VOLTAGE TRANSFORMER secondary
and filament terminals. It is extremely dangerous
to work on or near these circuits with the oven
energized.
DO NOT measure the voltage in the high voltage
circuit including filament voltage of magnetron.

PRECAUTION
Servicemen should remove their watches
whenever working close to or replacing the
magnetron.
- 2 -

2. Specifications
2-1 Table of Specifications
TIMER

99 MINUTES 99 SECONDS

POWER SOURCE

120V 60Hz, AC

POWER CONSUMPTION

MICROWAVE : 1,580W

OUTPUT POWER

FROM 100 TO 1000W(10 LEVEL POWER)

(IEC-705 TEST PROCEDURE)

OPERATING FREQUENCY

2,450MHz

MAGNETRON

OM75PH(31)ESS

COOLING METHOD

COOLING FAN MOTOR

OUTSIDE DIMENSIONS

297/8"(W) x 153/4"(H) x 151/6"(D) mm

NET WEIGHT

64.0 lbs

SHIPPING WEIGHT

71.7 lbs

- 3 -

3. Operating Instructions
3-1 Control Panel

3-2 Features & External Views

Door
Ventilation Holes

Oven Light

Safety Interlock Holes

Control Panel
Handle

Guide Roller

Intake Holes

417.25mm

Glass Tray

396mm

Door Latches

758.9mm

382.4mm

- 4 -

4. Disassembly and Reassembly

MAGNETRON, MOTOR ASSEMBLY, VENT BLOWER AND HIGH VOLTAGE TRANSFORMER
Oven must be removed from wall.
REMOVING OVEN FROM WALL ( 2 PEOPLE REQUIRED)
Oven is hooked on metal tabs at bottom of wall mounting plate and to cabinet by (3) top cabinet bolts.

4-1 Replacement of High Voltage Transformer and Fan Motor Assembly.

Disconnect power.
Remove Grille & Control Box Assembly.
1. Discharge the high voltage capacitor.
2. Disconnect all the leads.
3. Remove (2) screws from the fan motor
assembly.
4. Remove (3) screws from the duct-side.
5. Remove the duct-side.
6. Take out the fan motor.
7. Remove (4) Screws from the H.V.Trans.
8. Take out the H.V.Trans.

SCREW
SCREW

SCREW

SCREW

SCREW

(DUCT SIDE)

XMER SCREWS
(2 EACH SIDE)

4-2 Replacement of Magnetron

Remove the magnetron including the shield case,
permanent magnet, choke coils and capacitors
(all of which are contained in one assembly).

MGT NUTS (4)

1. Disconnect all lead wires from the magnetron.

2. Remove nuts (4) securing the magnetron to the
wave guide.
3. Take out the magnetron very carefully.
NOTE1: When removing the magnetron, make sure
that it antenna does not hit any adjacent
parts, or it may be damaged.
NOTE2: When replacing the magnetron, be sure to
remount the magnetron gasket in the correct
position and make sure the gasket is in good
condition.

CAUTION !
During replacement, be certain R.F. anode gasket is
in place around anode stub.

PERFORM MICROWAVE LEAKAGE TEST

- 7 -

4-3 Replacement of Door Assembly

4-3-1 Removal of Door "C"
Open the door and remove the door by
pulling up from hinge holes.

4-3-2 Removal of Door "E"

Following the procedure as shown in the figure,
insert and bend a thin metal plate between Door
"E" and Door "A" until you hear the 'tick' sound.

Door "E"

Insertion depth of the thin metal plate should be

0.5mm or less.

4-3-3 Removal of Key Door & Spring

Remove pin hinge from Door "E".
Detach spring from Door "E" and key door.
Door "E"

Key Door

- 8 -

4-3-4 Reassembly Test

After replacement of the defective component parts of the door, reassemble it and
follow the instructions below for proper installation and adjustment so as to
prevent an excessive microwave leakage.
1. When mounting the door to the oven, be sure to adjust the door parallel to the bottom line of the oven
face plate by moving the upper hinge and lower hinge in the direction necessary for proper alignment.
2. Adjust so that the door has no play between the inner door surface and oven front surface. If the door
assembly is not mounted properly, microwave energy may leak from the space between the door and oven.
3. Do the microwave leakage test.

4-4 Replacement of Fuse

The fuse is located behind the control panel mounted to the installation bracket.
1. Disconnect power and remove grille.
2. Remove a screw that secure the installation
bracket.
3. When 20A fuse blows out by the operation
of interlock monitor switch failure, replace
the primary interlock switch, secondary interlock
switch, door sensing switch, interlock monitor
switch and power relay.
4. When the above four switches operate properly,
check if any other part such as the control circuit
board, blower motor or high voltage transformer
is defective.
FUSE & FUSE HOLDER

4-5 Replacement of Drive Motor

1. Disconnect power and remove bottom plate
screws(7).
2. Remove bottom plate and disconnect the
turntable motor drive.
3. Remove turntable motor screws(2) and pull the
turntable motor out.
4. When replacing the drive motor, be sure to remount
it in the correct position with the coupler.
5. Connect all the leads to the drive motor.
6. Screw the drive motor cover to the base plate with
a screwdriver.

- 9 -

DRIVE MOTOR

4-6 Replacement of stirrer motor

1. Disconnect power and remove grille screws(2).
2. Remove grille and the bracket duct upper screw(1).
3. Remove the bracket duct upper and disconnect the
stirrer motor wire.
4. Remove stirrer motor screws(2) and pull the
stirrer motor.

STIRRER MOTOR

4-7 Removal of stirrer

The stirrer is motor driver and located on the upper side of the cavity. The oven uses a top feed wave guide.
The stirrer is located in the wave guide and the motor is located on the wave guide.
1. Disconnect power and open the door.
2. Remove the clip and turn the stirrer cover left.
3. Remove stirrer cover and the stirrer will come
with it.

CLIP

COVER STIRRER

STIRRER ASSEMBLY

COVER STIRRER

- 10 -

4-8 Replacement of Control Circuit Board

4-8-1 Removal of Control Box
1. Disconnect power and remove grille.
Screw

2. Be sure to ground any static electric charge in

your body and never touch the control circuit.
3. Disconnect the connectors from the control
circuit board.
4. Remove a screw securing the control box
assembly.

Control Box

4-8-2 Removal of P.C.B Assembly

1. Pull the lever end of the plastic fastener and
remove the Flexible Printed Circuit(FPC) of
membrane panel.
Screw

2. Remove screws (5) securing the control circuit

board.

FPC
connector

3. Lift up the control circuit board from the Ass'y

control box.

Screw

4. When reconnecting the FPC connector, make

sure that the holes on the connector are properly
engaged with the hooks on the Plastic Fastener.

4-8-3 Removal of Window Display & Membrane Panel

1. Window display should not be disassembled as
its mounting tabs will be broken. If repair work
is difficult, replace with Ass'y control panel.
Window Display

2. The membrane key board is attached to the

escutcheon base with double faced adhesive
tape. Therefore, applying hot air such as using of
hair dryer is recommended for smoother
removal.
3. When installing new membrane key board, make
sure that the surface of escutcheon base is
cleaned sufficiently so that any problems
(shorted contacts or uneven surface) can be
avoided.

Membrane Panel

- 11 -

Screw

Screw
Screw

INSTALLATION
The Microwave Oven is supported by a special
bracket assembly (mounting system) supplied
with the oven. The bracket assembly must be
mounted to the wall with toggle bolts through
the wall, and a lag screw into a wall stud.
After the bracket assembly is installed, the unit
can be slid over the two rails of the bracket
assembly. Two bolts are run down through
the cabinet bottom and into the oven case to
pull the oven up against the cabinet bottom.
NOTE : For easier removal and personal safety
it is recommended that two people
remove this product.

Mounting Plate

CAUTION!
The mounting surface must be capable of
supporting the cabinet load, in addition to the
64 pound product, plus additional loads of up
to 50 pounds or a total weight of 114 pounds.
This product cannot be installed to cabinet
arrangements such as an island or peninsula.
It must be mounted to both a top cabinet and
wall.

VENT BLOWER
The vent or exhaust blower is located at the top
of the oven. It is shipped for vertical exhaust but
can be changed to rear exhaust or recirculating
(See installation instrustions on how to change
and/or blower section on how to remove).

COOKTOP LIGHTS
One 40-watt screw base incandescent bulbs are
located on the bottom between the two grease
filters. The bulbs are user replaceable by removing
one screw and lowering access cover. The bulbs
could be difficult to remove when replaced for the
first time. a silicone glue is used to secure them
during shipping.

OVEN LIGHT
A 40-watt screw base incandescent bulb is located
in the top of the oven cavity at the front.
It is user replaceable by removing the top grill
(2 screws. On the front of outer case.) The bulb
is then accessible by removing a metal cover (1 screw).
- 5 -

REUSABLE GREASE FILTERS

The metal filter trap grease released by foods
on the cooktop. They also prevent flames from
foods on the cooktop from damaging the inside
of the microwave.
For this reason, the filters must ALWAYS be in
place when the hood the vent fan is used. The
grease filter should be cleaned once a month,
or as needed.

REMOVING CHARCOAL FILTER

To remove the charcoal filter, disconnect power
at the main fuse or circuit breaker panel or pull
the plug. Remove the top grille by removing the
2 screws that hold it in place.
Slide the filter towards the filter towards the
front of the oven and remove it.

Screws

AUTOMATIC FAN
An automatic fan feature protects the microwave
from too much heat rising from the cooktop below
it. If you have turned the fan on you may find
that you cannot turn it. The fan will automatically
turn off when the internal parts are cool. If may
stay on for 30 minutes or more after the cooktop
and microwave controls are turned off.

GRILLE REMOVAL
The top full-width grille is removable for service to
some components, such as : oven light, cavity
T.C.O, vent motor capacitor and fuse.
TO REMOVE GRILLE :
1. Disconnect oven power.
2. Remove screws (2) from grille outer case.
3. Lift off grille.

REMOVING OVEN FROM WALL

(2 PEOPLE REQUIRED)
Oven is hooked on metal tabs at bottom of wall
mounting plate and fastened to cabinet by (3) top
cabinet bolts.
CAUTION : Oven weights 64.0 lbs. Requires 2
people for removal.

1. Disconnect power cord. Top vented modelsdisconnect duct and remove damper assembly.
2. Remove (3) top cabinet bolts.
3. Pull unit forward slowly providing adequate
support to prevent dropping unit during removal
of last top cabinet bolts.

- 6 -

Remove 2 grille screws to remove the grill

5. Alignment and Adjustments

PRECAUTION
1. High voltage is present at the high voltage terminals during any cook cycle.
2. It is neither necessary nor advisable to attempt measurement of the high voltage.
3. Before touching any oven components or wiring, always unplug the oven from its power source and
discharge the high voltage capacitor.

5-1 High Voltage Transformer

1. Remove connectors from the transformer terminals
and check continuity.
2. Normal resistance readings are as follows:

Filament Terminals

SHV-7778UC1
Secondary

79 10%

Filament

Shows Continuity

Primary

0.43 10%
Primary
Terminals

(Room temperature = 20 C)

5-2 Low Voltage Transformer

1. The low voltage transformer is located on the
control circuit board.
2. Remove the low voltage transformer from the
PCB Ass'y and check continuity.
3. Normal resistor reading is shown in the table.

Resistance
Terminals
SLV-1350N(P)
127.7

1~2(Input)
4~5(Output 2.7V)

1.8

6~7(Output 7.0V)

2.0

7~8(Output 19.0V)

4.8

5-3 Magnetron
Magnetron Antenna

1. Continuity checks can indicate only an open

filament or a shorted magnetron. To diagnose an
open filament or shorted magnetron :
2. Isolate the magnetron from the circuit by
disconnecting its leads.
3. A continuity check across the magnetron filament
terminals should indicate one ohm or less.
4. A continuity check between each filament terminal
and magnetron case should read open.

Gasket Plate

Cooling Fins

- 12 -

5-4 High Voltage Capacitor

1.
2.
3.
4.
5.

Check continuity of the capacitor with the meter set at the highest resistance scale.
Once the capacitor is charged, a normal capacitor shows continuity for a short time, and then indicates 9M.
A shorted capacitor will show continuous continuity.
An open capacitor will show constant 9M.
Resistance between each terminal and chassis should read infinite.

5-5 High Voltage Diode

1. Isolate the diode from the circuit by disconnecting its leads.
2. With the ohm-meter set at the highest resistance scale, measure across the diode terminals. Reverse the
meter leads and read the resistance. A meter with 6V, 9V or higher voltage batteries should be used to
check the front-to back resistance of the diode (otherwise an infinite resistance may be read in both
directions). The resistance of a normal diode will be infinite in one direction and several hundred K in the
other direction.

5-6 Main Relay and Power Control Relay

1. The relays are located on the PCB Ass'y. Isolate them from the main circuit by disconnecting the leads.
2. Operate the microwave oven with a water load in the oven. Set the power level set to high.
3. Check continuity between terminals of the relays after the start pad is pressed.

5-7 Adjustment of Primary Switch, Door Sensing Switch and Monitor Switch
Precaution
For continued protection against radiation hazard, replace parts in accordance with the wiring diagram and be sure to
use the correct part number for the following switches: Primary and secondary interlock switches, and the interlock
monitor switch (replace all together). Then follow the adjustment procedures below. After repair and adjustment, be
sure to check the continuity of all interlock switches and the interlock monitor switch.

1. When mounting Primary switch and Interlock

Monitor switch to Latch Body, consult the figure.
2. No specific adjustment during installation of
Primary switch and Monitor switch to the latch
body is necessary.

Door Sensing S/W

3. When mounting the Latch Body to the oven

assembly, adjust the Latch Body by moving it so
that the oven door will not have any play in it.
Check for play in the door by pulling the door
assembly. Make sure that the latch keys move
smoothly after adjustment is completed.
Completely tighten the screws holding the Latch
Body to the oven assembly.

Body latch

Interlock Monitor S/W

4. Reconnect to Monitor switch and check the
continuity of the monitor circuit and all latch
switches again by following the components test
procedures.
5. Confirm that the gap between the switch
housing and the switch actuator is no more than
0.5mm when door is closed.
6. Interlock Switch Replacement - When
replacing faulty switches, be sure switch mounting
tabs are not bent, broken or otherwise deficient in
their ability to secure the switches in place.

Primary Interlock S/W

Door Open Door Closed

Primary Interlock switch

Monitor switch(COM-NC)

Door Sensing S/W

(Secondary Interlock S/W)

- 13 -

5-8 VENT EXHAUST BLOWER MOTOR

The blower is a two speed (HI-LO) capacitor run
blower assembly located on top of the microwave oven. The blower is operated by low
voltage relays located on the smart board.
The blower motor has 3 winding which can be
tested for continuity from the front by removing
the top grille and opening the control panel.

DAMPER ASM

RUN CAPACITOR
The run capacitor is located behind the top
grille above the control area. The capacitor is
used for more torque and electrical phasing.
Without the capacitor the blower might run but
would be much slower.

BLOWER ASM

TO TEST THE CAPACITOR

1. Remove grille, discharge capacitor and
disconnect one capacitor lead.
2. Make appropriate capacitor check (with
analog meter needle should rise then fall,
cap is charging then discharging).

BLOWER & DAMPER

ASM MTG SCREWS

TO TEST BLOWER WINDINGS:

1. Disconnect power and remove grille.
2. Open control panel and discharfe capacitor.
3. Disconnent two wires to run capacitor.
Continuity test across the two wires should ve
approximately 75 ohms of resistance. This test
allows you to read across all three windings at
the same time.

TO REMOVE VENT BLOWER

1. Remove unit from its installation.
2. Remove 5 screws securing damper and motor
assembly to top and back of unit and lift off.
(1screw os located under damper.)
3. Disconnect blower plug.
NOTE: Place blower wires in routing slots to
avoid pinching of wires.

- 14 -

5-9 THERMAL CUTOUT(TCO'S)

There are 4 different thermal cutouts in this unit with 4 different purposes. They are :
1. Oven thermal cutout (flame sensor), on cavity top.
2. Hood thermal cutout, inside control area on duct.
3. Bottom thermal cutout, on floor of control area.
4. Magnetron thermal cutout, on magnetron.

5-9-1 Oven Thermal Cutout(Flame sensor)

The oven thermal cutout(Cavity TCO) is located
on the top side of the oven cavity beside exhaust
duct with a temperature rating of 212OF(100OC)
and is non-resetable.
The cutout is tightly held to the top of the oven
cavity by a spring clip.
NOTE : If cutout cannot be removed from clip
oven will have to be removed from
installation and outer case removed.

OVEN THERMAL CUTOUT

STIRRER MOTOR

5-9-2 Hood Thermal Cutout

This cutout will protect the touch control from
excessive heat by turning the vent fan on at low
speed. If the surface units of the range are used
for long periods of time heat will build up and
could damage the microwave control. In order
to prevent this a thermal cutout is installed on the
duct behind the control. This cutout will close
(158OF/70OC - vent fan energized)and open
(104OF/40OC - vent fan de-energized) depending
on temperatures it sense.

HOOD THERMAL CUTOUT

To Remove hood Thermal Cutout :

1. Disconnect power and remove grille.

2. Remove control box assembly.

3. Remove two wire leads and unscrew one
screw capturing cutout on duct.
NOTE : It this cutout were to open it would be
difficult to detect. The only time it functions
is during an overheat condition. It will be
normally open when checked with an ohmmeter.
- 15 -

BOTTOM THERMAL CUTOUT

5-9-3 Bottom Thermal Cutout

During a fire on the stove the heat could be intense
enough to close the Hood Thermal Cutout and force
the fan to run. While at moderate high temperature we
do want it to run, however during a fire it is advantageous to NOT have the vent fan running. So if a fire were
to start on the stove top the Bottom Thermal Cutout
would open at 248OF(120OC) and remove all power to
the microwave oven.
This cutout is designed to not be resetable.
To Remove Bottom Thermal Cutout :
1. Disconnect power and remove grille.
2. Remove control box assembly.
3. Remove two wire leads and unscrews one screw
capturing cutout on base plate.

HOOD THERMAL CUTOUT

BOTTOM THERMAL CUTOUT

5-9-4 Magnetron Thermal Cutout

The magnetron thermal cutout is located above the
leads to the magnetrons. It is designed to prevent
damage to the magnetron if an overheated condition
develops in the tube to cooling fan failure, obstructed
air ducts, dirty or blocked air intake.
Under normal operation, the magnetron thermal cutout
remains closed. However, when abnormally high temperatures are reached within the magnetron, the
magnetron thermal cutout will open at 320OF(160OC)
causing the oven to shut down. After the temperature
drops to 140OF(60OC) it will reset and cooking will be
able to resume.

MAGNETRON THERMAL CUTOUT

MAGNETRON

To Remove Magnetron Thermal Cutout :

1. See 'Removing Magnetron'.

- 16 -

5-10 SENSOR
The Sensor Cooking Function uses a special gas
sensor which detects both humidity(steam) and
hydrocarbons(food odors) during the cooking
process. Before conducting either of the sensor
tests below, ensure the unit is plugged into a will
outlet for at least 5 minutes. If already plugged
in, proceed. The sensor is a plug-in device
located in the vent area at the top left hand
corner of the cavity behind the grille.

VENT MOTOR

To Service :
1. Disconnect power and remove grille.
2. Separate retainer from receptacle and
unplug sensor.

GAS SENSOR

SENSOR COOKING TEST

1.
2.
3.
4.

Place 1/3 cup tap water in oven.

Touch potato , the oven starts immediately.
Control Beeps and Shuts off.
Touch Pause/Cancel .
1) Test OK - Normal
2) Test Fails - Check Sensor. See Sensor Test Below.

SENSOR TEST (QUICK TEST)

1. With 2 fingers touch and hold the following pads at the same time :
Auto Defrost and Sensor Reheat
2. Observe diagnostic number in display (Numbers approximate).
15-185 (Normal-verify with "detection test" )
213 or Higher (Sensor failed to open, sensor
unplugged, wiring or smart board.)
Less then 6 (shorted sensor, or smart board).

NOTE : Only heater terminals ( H ; Black and Red leads) can be checked with ohmmeter(30).
CAUTION : DO NOT ATTEMPT TO CHECK SENSOR TERMINALS (White and Orange leads).
CAN DAMAGE SENSOR.

- 17 -

5-11 Output Power of Magnetron

CAUTION
MICROWAVE RADIATION
PERSONNEL SHOULD NOT ALLOW EXPOSURE TO MICROWAVE RADIATION FROM MICROWAVE
GENERATOR OR OTHER PARTS CONDUCTING MICROWAVE ENERGY.
The output power of the magnetron can be measured by performing a water temperature rise test.
Equipment needed :
* Two 1-liter cylindrical borosilicate glass vessel (Outside diameter 190 mm)
* One glass thermometer with mercury column
NOTE: Check line voltage under load. Low voltage will lower the magnetron output. Make all temperature
and time tests with accurate equipment.
1. Fill the one liter glass vessel with water.
2. Stir water in glass vessel with thermometer, and record glass vessel's temperature ("T1", 101 C).
3. After moving the water into another glass vessel, place it in the center of the cooking tray. Set the oven to
high power and operate for 44 seconds exactly. (3 seconds included as a holding time of magnetron
oscillation.)
4. When heating is finished, stir the water again with the thermometer and measure the temperature ("T2").
5. Subtract T1 from T2. This will give you the water temperature rise. (T)
6. The output power is obtained by the following formula;
Output Power = 4.187 x 1000 x T+ 0.55 x Mc x (T2-T0)
41

44 : Heating Time (sec)

(3 seconds included as a holding time
of magnetron oscillation.)
4.187 : Coefficient for Water
1000 : Water (cc)
T : Temperature Rise (T1-T2)
To : Room Temperature
Mc : Cylindrical borosilicate glass weight

7. Normal temperature rise for this model is 9.9 C to 10.3C at 'HIGH'.

NOTE 1: Variations or errors in the test procedure will cause a variance in the temperature rise.
Additional power test should be made if temperature rise is marginal.
NOTE 2: Output power in watts is computed by multiplying the temperature rise (step 5) by a factor of 90
times the of centigrade temperature.

- 18 -

5-12 Procedure for Measurement of Microwave Energy Leakage

1) Pour 27515cc of 205 C(689 F) water in a beaker
which is graduated to 600cc, and place the beaker in
the center of the oven.
2) Start to operate the oven and measure the leakage by
using a microwave energy survey meter.
3) Set survey meter with dual ranges to 2,450MHz.
4) When measuring the leakage, always use the 2 inch
spacer cone with the probe. Hold the probe
perpendicular to the cabinet door. Place the spacer
cone of the probe on the door and/or cabinet door
seam and move along the seam, the door viewing
window and the exhaust openings moving the
probe in a clockwise direction at a rate of 1 inch/sec. If the leakage testing of the cabinet door seam is
taken near a corner of the door, keep the probe perpendicular to the areas making sure that the probe end
at the base of the cone does not get closer than 5cm to any metal. If it gets closer than 5cm, erroneous
readings may result.
5) Measured leakage must be less than 4mW/cm2, after repair or adjustment.

Maximum allowable leakage is 5mW/cm2.

4mW/cm2 is used to allow for measurement and meter accuracy.

5-13 Check for Microwave Leakage

1. Remove the outer panel.
2. Pour 27515cc of 205C(689F) water in a beaker
which is graduated to 600cc, and place the beaker in
the center of the oven.
3. Start the oven at the highest power level.
4. Set survey meter dual ranges to 2,450MHz.
5. Using the survey meter and spacer cone as described
above, measure near the opening of magnetron, the
surface of the air guide and the surface of the wave
guide as shown in the following photo.( but avoid the
high voltage components.) The reading should be less than 4mW/cm2 .

5-14 Note on Measurement

1) Do not exceed the limited scale.
2) The test probe must be held on the grip of the handle, otherwise a false reading may result when the
operator's hand is between the handle and the probe.
3) When high leakage is suspected, do not move the probe horizontally along the oven surface; this may
cause damage to the probe.
4) Follow the recommendation of the manufacturer of the microwave energy survey meter.

5-15 Leakage Measuring Procedure

5-15-1 Record keeping and notification after measurement.
1) After adjustment and repair of a radiation preventing device, make a repair record for the measured
values, and keep the data.
2) If the radiation leakage is more than 4 mW/cm2 after determining that all parts are in good condition,
functioning properly and the identical parts are replaced as listed in this manual notify that fact to ;
Samsung Electronics America, Inc.
Headquarters 105 Challenger Road
Ridge field Pack, New Jersey 07660-0511
5-15-2 At least once a year have the microwave energy survey meter checked for accuracy by its
manufacturer.
- 19 -

6. Troubleshooting
PRECAUTION
1.
2.
3.
4.

CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.

BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
DISCHARGE THE HIGH VOLTAGE CAPACITOR.
WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT
ONE LEAD WIRE FROM THESE PARTS AND THEN CHECK CONTINUITY WITHOUT THE
POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE READING OR DAMAGE
TO YOUR METER.
5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE
STATIC DISCHARGE MAY DAMAGE IT.
ALWAYS TOUCH GROUND WHILE WORKING ON IT TO DISCHARGE ANY STATIC CHARGE
BUILT UP.

6-1 Electrical Malfunction

SYMPTOM

CAUSE

CORRECTIONS

1. Open or loose lead wire harness

Oven is dead.
2. Open thermal cutout (Magnetron)
Fuse is OK.
3. Open low voltage transformer
No display and no operation at all .
4. Defective Ass'y PCB
No display and no operation at all.
Fuse is blown.

1. Shorted lead wire harness

2. Defective primary latch switch
(NOTE 1)
3. Defective monitor switch (NOTE1)
4. Shorted H.V.Capacitor
5. Shorted H.V.Transformer (NOTE2)

Check fan motor when thermal

cutout is defective.
Check Ass'y PCB when L.V.T is
defective.
Check adjustment of primary,
interlock monitor,
power relay, door sensing
switch.

NOTE 1: All of these switches must be replaced at the same time.

(refer to adjustment instructions)
Check continuity of power relay contacts and if it has
continuity, replace power relay also.
NOTE 2: When H.V.Transformer is replaced, check diode and
magnetron also.
Oven does not accept
key input (Program)

Timer starts countdown but no

microwave oscillation.
(No heat while oven lamp and fan
motor turn on.

1. Key input is not in-Sequence

2. Open or loose connection of
membrane key pad to Ass'y PCB
3. Shorted or open membrane panel
4. Defective Ass'y PCB

Refer to operation procedure.

1. Off-alignment of latch switches

2. Open or loose connection of high
voltage circuit especially
magnetron filament circuit
NOTE: Large contact resistance will
bring lower magnetron
filament voltage and cause
magnetron to lower output
and/or intermittent oscillation.
3. Defective high voltage
components, H.V.Transformer, H.V.
Capacitor, H.V.Diode, Magnetron
4. Open or loose wiring of power relay
5. Defective primary latch switch
6. Defective power relay or Ass'y PCB

Adjust door and latch switches.

- 20 -

Replace PCB main.

Check high voltage component

according to component test
procedure and replace if it is
defective.

Replace PCB main.

6-1 Electrical Malfunction(continued)

SYMPTOM

CAUSE

CORRECTIONS

Oven lamp and fan motor turn on

1. Misadjustment or loose wiring

of primary latch switch
2. Defective primary latch switch

Oven can program but timer

does not start.

1. Open or loose wiring of

secondary interlock switch
2. Off-alignment of primary
interlock
3. Defective secondary interlock S/W

Microwave output is low :

Oven takes longer time to
cook food.

1. Decrease in power source

voltage.
2. Open or loose wiring of
magnetron filament circuit.
(Intermittent oscillation))
3. Aging of magnetron

Adjust door and latch switches.

Adjust door and interlock switches.

Consult electrician.

Fan motor turns on when plugged in Loose wiring of door sensing switch Check wire of door sensing switch.
Oven does not operate and return to Defective Ass'y PCB
the plugged in mode.

Replace PCB main.

Loud buzzing noise can be heard.

Tighten screws of fan motor.

Tighten screws of
H.V.Transformer.
Replace H.V.Diode.

1. Loose fan and fan motor

2. Loose screws on
H.V.Transformer
3. Shorted H.V.Diode

Turntable and stirrer motor does not 1. Open or loose wiring of

rotate.
turntable and stirrer motor.
2. Defective turntable and stirrer
motor.

Replace turntable motor.

Replace stirrer motor.

Oven stops operation during

cooking

1. Open or loose wiring of primary

interlock switch
2. Operation of thermal
cutout(Magnetron)

Adjust door and latch switches.

Sparks

1. Metallic ware or cooking dishes

touching on the oven wall.
2. Ceramic ware trimmed with
gold or silver powder also
causes sparks.

Uneven cooking

Noise from the turntable motor

when it starts to operate.

Uneven intensity of microwave due

to its characteristics.

Noise may result from the motor.

- 21 -

Inform the customer.

Do not use any type of cookware
with
metallic trimming.
Wrap thinner parts of the food with
aluminum foil.
Use plastic wrap or cover with a
lid.
Stir once or twice while cooking
foods such as soup, cocoa, or
milk.
Replace turntable motor.

6. Troubleshooting
PRECAUTION
1.
2.
3.
4.

CHECK GROUNDING BEFORE CHECKING FOR TROUBLE.

BE CAREFUL OF THE HIGH VOLTAGE CIRCUIT.
DISCHARGE THE HIGH VOLTAGE CAPACITOR.
WHEN CHECKING THE CONTINUITY OF THE SWITCHES OR TRANSFORMER, DISCONNECT
ONE LEAD WIRE FROM THESE PARTS AND THEN CHECK CONTINUITY WITHOUT THE
POWER SOURCE ON. TO DO OTHERWISE MAY RESULT IN A FALSE READING OR DAMAGE
TO YOUR METER.
5. DO NOT TOUCH ANY PART OF THE CIRCUIT OR THE CONTROL CIRCUIT BOARD, SINCE
STATIC DISCHARGE MAY DAMAGE IT.
ALWAYS TOUCH GROUND WHILE WORKING ON IT TO DISCHARGE ANY STATIC CHARGE
BUILT UP.

6-1 Electrical Malfunction

SYMPTOM

CAUSE

CORRECTIONS

1. Open or loose lead wire harness

Oven is dead.
2. Open thermal cutout (Magnetron)
Fuse is OK.
3. Open low voltage transformer
No display and no operation at all .
4. Defective Ass'y PCB
No display and no operation at all.
Fuse is blown.

1. Shorted lead wire harness

2. Defective primary latch switch
(NOTE 1)
3. Defective monitor switch (NOTE1)
4. Shorted H.V.Capacitor
5. Shorted H.V.Transformer (NOTE2)

Check fan motor when thermal

cutout is defective.
Check Ass'y PCB when L.V.T is
defective.
Check adjustment of primary,
interlock monitor,
power relay, door sensing
switch.

NOTE 1: All of these switches must be replaced at the same time.

(refer to adjustment instructions)
Check continuity of power relay contacts and if it has
continuity, replace power relay also.
NOTE 2: When H.V.Transformer is replaced, check diode and
magnetron also.
Oven does not accept
key input (Program)

Timer starts countdown but no

microwave oscillation.
(No heat while oven lamp and fan
motor turn on.

1. Key input is not in-Sequence

2. Open or loose connection of
membrane key pad to Ass'y PCB
3. Shorted or open membrane panel
4. Defective Ass'y PCB

Refer to operation procedure.

1. Off-alignment of latch switches

2. Open or loose connection of high
voltage circuit especially
magnetron filament circuit
NOTE: Large contact resistance will
bring lower magnetron
filament voltage and cause
magnetron to lower output
and/or intermittent oscillation.
3. Defective high voltage
components, H.V.Transformer, H.V.
Capacitor, H.V.Diode, Magnetron
4. Open or loose wiring of power relay
5. Defective primary latch switch
6. Defective power relay or Ass'y PCB

Adjust door and latch switches.

- 20 -

Replace PCB main.

Check high voltage component

according to component test
procedure and replace if it is
defective.

Replace PCB main.

6-1 Electrical Malfunction(continued)

SYMPTOM

CAUSE

CORRECTIONS

Oven lamp and fan motor turn on

1. Misadjustment or loose wiring

of primary latch switch
2. Defective primary latch switch

Oven can program but timer

does not start.

1. Open or loose wiring of

secondary interlock switch
2. Off-alignment of primary
interlock
3. Defective secondary interlock S/W

Microwave output is low :

Oven takes longer time to
cook food.

1. Decrease in power source

voltage.
2. Open or loose wiring of
magnetron filament circuit.
(Intermittent oscillation))
3. Aging of magnetron

Adjust door and latch switches.

Adjust door and interlock switches.

Consult electrician.

Fan motor turns on when plugged in Loose wiring of door sensing switch Check wire of door sensing switch.
Oven does not operate and return to Defective Ass'y PCB
the plugged in mode.

Replace PCB main.

Loud buzzing noise can be heard.

Tighten screws of fan motor.

Tighten screws of
H.V.Transformer.
Replace H.V.Diode.

1. Loose fan and fan motor

2. Loose screws on
H.V.Transformer
3. Shorted H.V.Diode

Turntable and stirrer motor does not 1. Open or loose wiring of

rotate.
turntable and stirrer motor.
2. Defective turntable and stirrer
motor.

Replace turntable motor.

Replace stirrer motor.

Oven stops operation during

cooking

1. Open or loose wiring of primary

interlock switch
2. Operation of thermal
cutout(Magnetron)

Adjust door and latch switches.

Sparks

1. Metallic ware or cooking dishes

touching on the oven wall.
2. Ceramic ware trimmed with
gold or silver powder also
causes sparks.

Uneven cooking

Noise from the turntable motor

when it starts to operate.

Uneven intensity of microwave due

to its characteristics.

Noise may result from the motor.

- 21 -

Inform the customer.

Do not use any type of cookware
with
metallic trimming.
Wrap thinner parts of the food with
aluminum foil.
Use plastic wrap or cover with a
lid.
Stir once or twice while cooking
foods such as soup, cocoa, or
milk.
Replace turntable motor.

7. Exploded Views and Parts List

7-1 Exploded Views
MM158
MM032

MM121
MM161

MM122

MM163

MM141

MM152

MM157

MM061

MM142

MM146

MM10
MM64

MM36

MM151

MM221

MM172

MM46
MM01
MM86
MM162
MM165

MM701
MM42
MM20

MM156

MM154

MM08
MM34

MM22
MM66

MM17
MM155

MB01
MM55

MD06
MD01

MM149
MB05
MB03
MC22

MM29

MD05
MD04
MD11

MM07

MM06

MM702

MM30

MM171

MM31
MB02
MB04
MD17

MM18
MM14

MC07

MD02

MM19

MC57

MD07
MD10

MM173
MM281

MD13
MC03
MC13

MM140

MC02

MM36

MC06

MD141

MM03

MM28
MM47

MC01

MM153
MM148
MM164
A

- 22 -

7-2 Main Parts List

No.
MB01
MB02
MB03
MB04
MB05
MM01
MM01
MM01
MM03
MM032
MM06
MM061
MM07
MM08
MM10
MM10
MM121
MM122
MM14
MM140
MM141
MM142
MM146
MM147
MM148
MM149
MM151
MM152
MM153
MM154
MM155
MM156
MM156
MM156
MM157
MM158
MM161
MM162
MM163
MM164
MM164
MM164
MM165
MM17
MM171
MM172
MM173
MM18
MM19
MM20
MM22
MM221
MM28
MM28
MM28
MM281
MM29
MM30
MM31
MM34
MM36
MM42
MM46
MM55
MM64
MM66
MM701
MM702
MM86

Code No.
DE96-00154A
3405-000176
3405-000178
DE66-90106B
DE61-00249A
DE70-10017H
DE70-10017G
DE70-10017J
DE39-00024A
DE39-40678A
DE92-90552C
DE31-10178A
DE39-10102A
OM75P(10)ESS
4713-001013
4713-001013
DE32-60013A
DE61-90111A
DE26-10136A
DE92-90505A
DE72-50098A
DE61-50469A
DE92-90508A
DE61-50464A
DE67-40152A
DE59-50002A
DE61-50507A
DE61-50545A
DE63-30011A
DE71-60384A
DE72-50084A
DE64-00325B
DE64-00325A
DE64-00325C
DE63-30016A
DE92-90242A
DE61-50542A
DE66-20095B
DE70-40279A
DE71-60385C
DE71-60385B
DE71-60385C
DE65-00004A
DE47-20007A
DE47-20020A
DE47-20196A
DE47-20059A
DE74-20016A
DE92-90495A
DE67-60012A
DE31-10172A
DE31-10173A
DE61-00245C
DE61-00245B
DE61-00245C
DE80-10121B
2501-001011
DE61-50120A
DE91-70063A
3602-001002
DE47-00006A
DE61-00027A
DE97-00178B
3601-001198
DE97-00266A
DE61-50540A
DE61-00039B
DE61-00040B
DE71-60121A

Description
ASSY BODY LATCH
SWITCH-MICRO
SWITCH-MICRO
LEVER-SWITCH LOWER
BODY-LATCH
PANEL-OUTER
PANEL-OUTER
PANEL-OUTER
WIRE HARNESS-A
WIRE HARNESS-S
ASSY-MOTOR FAN
MOTOR-VENTILATION
ASSY POWER CORD
ASSY-MAGNETRON:OM75P
LAMP-INCANDESCENT
LAMP-INCANDESCENT
SENSOR-GAS
HOLDER-SENSOR
TRANS-H.V
ASSY-HARD WARE
DUCT-UPPER
BRACKET-DUCT UPPER
ASSY-HOLDER NUT
BRACKET-BOTTOM LAMP
GLASS-COOKTOP LAMP
CAPACITOR-MOTOR
BRACKET-POWER CORD
BRACKET-V/T MOTOR
FILTER-AIR
COVER-FRONT
DUCT-SIDE
GRILLE
GRILLE
GRILLE
FILTER-CHAROCAL
ASSY-HOOD DAMPER
BRACKET-FILTER
BUTTON-LOCK
PLATE-MOUNTING
COVER-GLASS
COVER-GLASS
COVER-GLASS
CLIP-GRILLE
THERMOSTAT
THERMOSTAT
THERMOSTAT
THERMOSTAT
TRAY-COOKING
ASSY-GUIDE ROLLER
COUPLER
MOTOR-SYNCHRONOUS
MOTOR-SYNCHRONOUS
BASE-BOTTOM
BASE-BOTTOM
BASE-BOTTOM
BASE-PLATE
C-OIL
BRACKET-HVC
ASSY-HVD
FUSE-HOLDER
HOLDER-LAMP
BRACKET-GRILLE
ASSY-STIRRER
FUSE-CARTRIDGE
ASSY-WIRE RACK(SUB)
BRACKET-AIR GUIDE-A
HOLDER-RACK(A)
HOLDER-RACK(B)
COVER-STIRRER

Specification
SSOTR6/7,250V,15A,200gf,SPST-NC
250V,15A,200gf,SPST-NO
PBT,T2.0,1.9G,OTR6,-,-,SSOTR,PBT(VB5050)/PP(FH44N),T2.0,NTR,SSOTR (1.6 CUFT),V/STEEL,TO.5+0.2,W399.8,SSOTR (1.6 CUFT),V/STEEL,TO.5+0.2,W399.8,SSOTR (1.6 CUFT),V/STEEL,TO.5+0.2,W399.8,SSOTR,120V60HZ,SEA,-,-,-,-,-,-,-,-,-,-,-,-,120V60HZ,JVM1450,60,GE,-,-,JVM-1650/1660,-,-,SMV-260UA,120V,60Hz,3180/2400r
AP-30,DR-4,SJT3/14,1310MM,UL,G
130V,-,40W,ORG,E17/20,-,25X73
130V,-,40W,ORG,E17/20,-,25X73
ST-MWO,-,-,-,-,-,-,POM(DURACON-M90-02),-,-,-,-,SHV-7778UC1,120V,2265V/3.25V,6
OTR6,-,-,-,-,-,PP-G430,-,-,-,-,-,SECC,T0.8,W206,L272,OTR6,OTR6,-,-,-,-,-,SECC,T0.5,W71.5,L586,OTR6,OTR6,GLASS,T3.0,W71,L194,-,TRP,SH-M 10UF,220V10UF,DMB-2BJ10MMC,-,SECC,T0.8,W40,L56,OTR6,-,SECC,T0.6,W120,L315,-,-,T0.3,-,-,-,-,AL,-,SECC,T0.8,W90,L220,-,OTR6,-,SECC,T0.8,W256,L316,-,SSOTR,GOOD-DESIGN,PC LEXAN141,T2.5,SSOTR,GOOD-DESIGN,PC LEXAN141,T2.5,SSOTR,GOOD-DESIGN,PC LEXAN141,T2.5,-,NEW,-,-,-,-,JX81A,JVM-250BL,OTR4,-,-,-,-,SECC,T0.6,W70,L144,-,-,-,OTR5,-,-,TB53)
-,SECC,-,T0.8,W440,OTR6,L775,-,SSOTR (1.4CUFT),SECC,T0.5,-,-,-,-,GRAY,SSOTR (1.4CUFT),SECC,T0.5,-,-,-,-,BLK,SSOTR (1.4CUFT),SECC,T0.5,-,-,-,-,GRAY,JVM-1860,STS,-,T0.6,-,PW-2N(160/60)187Z,250V7.5A,160
PW-2R(40/70,Z,23.8),250V/7.5A,
NT-101NA(8XV)P,100/0,250V/7.5A
PW-2N(8XV),125V15A,V,120/0,23.
GLASS,T5.0,M551T,-,OTR6-ALL,T/T+S/T,PI-15,-,-,SPS,-,12G,-,-,M2HJ24Z709,ST-16F,21V,3RPM,FCL
M2HJ29A709,ST-16F,21V,34.9RPM,
SSOTR (1.6 CUFT),SECC,T0.5,GRAY COATING,SSOTR (1.6 CUFT),SECC,T0.5,BLK COATING,SSOTR (1.6 CUFT),SECC,T0.5,GRAY COATING,SSOTR7,SGCC1,T0.8,-,-,-,910nF,2100V,BK,54x35x75mm,20mm
-,SECC,T0.6,W62,L72,-,V2M6,PI9.0,0.05MT,-,125V/250V,15A/7.5A,50mohm
-,250V,75W,250X187 2POLE,OTR7,-,-,JVM1630,SECC,T0.5,W60,L170,-,OTR7,OTR8 B/STIRRER+OTR8 H/STIRRER,250V,20A,SLOW-BLOW,CERAMIC,6.35x31.3mm
SSOTR-1.6CUFT,SUB ASSY,-,-,SECC,T0.6,W233,L111,NTR,OTR7,PP(GP30%),T2.0,-,-,GE-WHT,OTR7,PP(GP30%),T2.0,-,-,GE-WHT,-,PP,T2.0,W7,L198,-,85G,-

- 23 -

Q'ty
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
3
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
4
4
1

Remark

MO1650WA
MO1650BA
MO1650CA

DUCT-U

MO1650WA
MO1650BA
MO1650CA

MGT
CAVITY
BASE-PLATE

T/T
S/T
MO1650WA
MO1650BA
MO1650CA

GRILLE

7-3 Control and Door Parts List

No.

Code No.

MC01

ASSY CONTROL-BOX

120V60HZ,MO1650WA,WHT,GOOD-DESIGN

S.N.A

MC01

ASSY CONTROL-BOX

120V60HZ,MO1650WA,BLK,GOOD-DESIGN

S.N.A

MC01

ASSY CONTROL-BOX

120V60HZ,MO1650WA,BISQUE,GOOD-DESIGN

S.N.A

MC02

DE34-00038N

SWITCH MEMBRANE

MO1650WA,-,W150.9*L238.4,PC,-,5V,-,-,-,-,-

MO1650WA

MC02

DE34-00038M

SWITCH MEMBRANE

MO1650WA,-,W150.9*L238.4,PC,-,5V,-,-,-,-,-

MO1650BA

MC02

DE34-00038P

SWITCH MEMBRANE

MO1650WA,-,W150.9*L238.4,PC,-,5V,-,-,-,-,-

MO1650CA

MC03

DE64-00331B

CONTROL-PANEL

SSOTR,GOOD-DESIGN,PC LEXAN121,T2.5,WHT,-

MO1650WA

MC03

DE64-00331A

CONTROL-PANEL

SSOTR,GOOD-DESIGN,PC LEXAN121,T2.5,BLK,-

MO1650BA

MC03

DE64-00331C

CONTROL-PANEL

SSOTR,GOOD-DESIGN,PC LEXAN121,T2.5,--

MO1650CA

MC06

DE64-00416A

WINDOW-DISPLAY

SSOTR,GOOD-DESIGN,SAN,T2.0,-,-,-,SMG(G0140),-

MC07

RA-SSOTR-01

ASSY PCB PARTS

MO1650WA,120V60HZ

MC13

DE94-00587B

ASSY CONTROL-PANEL

-,SSOTR6,WHT,-

MO1650WA

MC13

DE94-00587A

ASSY CONTROL-PANEL

,SSOTR6,BLK,-

MO1650BA

MC13

DE94-00587C

ASSY CONTROL-PANEL

SSOTR6,BISQUE

MO1650CA

MC22

DE39-40674A

WIRE HARNESS-B

120V60HZ,JVM1420,30,40,50,GE,-

MC57

DE97-00255A

ASSY-BKT C/PANEL

MO1650WA/MO1450WA,-,-,-

MD01

ASSY DOOR

SSOTR,1.6CUFT,WHT,GOOD-DESIGN,ASSEMBLY

S.N.A

MD01

ASSY DOOR

SSOTR,1.6CUFT,BLK,GOOD-DESIGN,ASSEMBLY

S.N.A

ASSY DOOR

SSOTR,1.6CUFT,BISQUE,GOOD-DESIGN,ASSEMBLY

S.N.A

MD01

Description

Specification

Q'ty

Remark

MD02

DE64-00328B

DOOR-A

SSOTR,GOOD-DESIGN,PC LEXAN121,T2.5,H35,-

MO1650WA

MD02

DE64-00328A

DOOR-A

SSOTR,GOOD-DESIGN,PC LEXAN121,T2.5,H35,-

MO1650BA

MD02

DE64-00328C

DOOR-A

SSOTR,GOOD-DESIGN,PC LEXAN121,T2.5,H35,-

MO1650CA

MD04

DE94-00586B

ASSY DOOR-E

SSOTR7,COATING,-

MD05

DE01-00091A

FILM-DOOR

MD06

DE64-00337A

DOOR-C

MO1650WA,PP,T2.0,-,-,-,BLK,-

MD07

DE61-00151A

SPRING-KEY

JVM-1860,HSWR,PI0.95,-,-,-,OD8.5,-,-,-,-

MD10

DE64-00157A

DOOR-KEY

JVM-1860,POM(KEPITAL F20-02),-,BLK,-,-,-

MD11

DE94-00603A

ASSY DOOR-E(SUB)

SSOTR7,BLK COATING+FILM DOOR,-

MD13

DE60-60008A

PIN-HINGE

PI4,L17,MSWR10,M301TBC,-,-,-,-

MD141

DE97-00250B

ASSY-HANDLE

SSOTR,GOOD-DESIGN,WHT,-,-

MO1650WA

MD141

DE97-00250A

ASSY-HANDLE

SSOTR,GOOD-DESIGN,BLK,-,-

MO1650BA

MD141

DE97-00250C

ASSY-HANDLE

SSOTR,GOOD-DESIGN,BISQUE,-,-

MO1650CA

MD17

DE64-00444A

SCREEN-DOOR(B)

SSOTR,GOOD-DESIGN,REINFORCE GLASS,T3.2,-

S.N.A : SERVICE NOT AVAILABLE

- 24 -

7-4 Standard Parts List

Code No.

Description

Specification

Q'ty

Remark

6002-001170

SCREW-TAPPING

FH,STAR,2,M4,L12,SIL,SWRCH18A

B/D-LATCH

6002-001174

SCREW-TAPPING

FH,+,2S,M4,L12,NI PLT,MSWR

GRILLE

DE60-10012A

SCREW-TAP TITE

-,SWR10,M4,L10,TH,+,-,3,ZPC2,-

P-CORD

DE60-10045A

SCREW-TAP PH

-,-,FEFZY,-,PH,M3,-,L6,-,-

MGT

DE60-10051A

SCREW-TAP PH

-,-,MSWR,-,PH,M4,-,L6,-,-

S/T-MO

DE60-10052A

SCREW-TAP PH

-,-,FEFZY,-,PH,M4,-,L8,-,-

BKT-HI

DE60-10052A

SCREW-TAP PH

-,-,FEFZY,-,PH,M4,-,L8,-,-

T/T-MO

DE60-10063A

SCREW-TAP TH

-,-,FEFN,-,TH,M4,-,L12,-,-

BKT-P/CORD

DE60-10063A

SCREW-TAP TH

-,-,FEFN,-,TH,M4,-,L12,-,-

C/BOX

DE60-10063A

SCREW-TAP TH

-,-,FEFN,-,TH,M4,-,L12,-,-

HOOD

DE60-10063A

SCREW-TAP TH

-,-,FEFN,-,TH,M4,-,L12,-,-

PN-OUT

DE60-10067A

SCREW-TAP TH

-,-,FEFZB,2-SLOT,TH,M4,-,L8,-,-

B-DUCT

DE60-10067A

SCREW-TAP TH

-,-,FEFZB,2-SLOT,TH,M4,-,L8,-,-

DUCT-U

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

BASE-P

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

DUCT-S

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

DUCT-U

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

FAN-MO

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

FRONT

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

GU-AIR

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

MOUNT

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

PN-OUT

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

VENT-M

DE60-10080A

SCREW-WASHER

-,-,-,-,M5,L12,-,2S,-,-

HVT

DE60-10082H

SCREW-A

-,-,-,-,2S-4X12,TOOTHED,-,-,-,-

BASE-P

DE60-10082H

SCREW-A

-,-,-,-,2S-4X12,TOOTHED,-,-,-,-

PN-OUT

DE60-10122A

SCREW-TAP TH

-,-,FE,FN,TAP,TH,-,2-4X8,-,-

BOTTOM

DE60-10122A

SCREW-TAP TH

-,-,FE,FN,TAP,TH,-,2-4X8,-,-

PN-OUT

DE60-30015A

NUT-FLANGE

M5,P0.8,MSWR10,FEFZY,-,-,-,-,-

MGT

DE60-10045A

SCREW-TAP PH

-,-,FEFZY,-,PH,M3,-,L6,-,-

TCO

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

CA-MOT

6002-001004

SCREW-TAPPING

TH,+,2,M4,L30,ZPC(YEL),SWRCH18

DE60-10052A

SCREW-TAP PH

-,-,FEFZY,-,PH,M4,-,L8,-,-

DE60-10082H

SCREW-A

-,-,-,-,2S-4X12,TOOTHED,-,-,-,-

BKT-HVC

DE60-10082H

SCREW-A

-,-,-,-,2S-4X12,TOOTHED,-,-,-,-

DIODE

DE60-10053A

SCREW-TAP PH

-,-,FEFZY,-,PH,M4,-,L10,-,-

DOOR-A

DE60-10053A

SCREW-TAP PH

-,-,FEFZY,-,PH,M4,-,L10,-,-

HANDLE

DE60-10088A

SCREW-TAP PH

-,-,FEFZY,PLAIN,PH,M3,-,L8,-,-

ASSY-PCB

DE60-10045A

SCREW-TAP PH

-,-,FEFZY,-,PH,M3,-,L6,-,-

B/T-TCO

DE60-10122A

SCREW-TAP TH

-,-,FE,FN,TAP,TH,-,2-4X8,-,-

DE60-10069A

SCREW-TAP TH

-,-,FRFZY,-,TH,M4,-,L10,-,-

- 25 -

BKT-GRILLE