STB9NK60Z, STP9NK60Z, STP9NK60ZFP

STB9NK60Z, STP9NK60Z, STP9NK60ZFP
N-channel 600 V, 0.85 typ., 7 A Zener-protected SuperMESH

Power MOSFET in DPAK, TO-220 and TO-220FP packages
Datasheet production data
Features
Order codes
VDS
RDS(on) max
ID
STB9NK60ZT4
STP9NK60Z
PTOT
3
600
V
0.95
STP9NK60ZFP
Extremely high dv/dt capability
Improved ESD capability
100% avalanche tested
Gate charge minimized
Very low intrinsic capacitances
7A
125 W
D2PAK
TO-220
30 W
3
1
TO-220FP
Applications
TAB
TAB
Figure 1.
Internal schematic diagram

, TAB
Switching applications
Description
These devices are N-channel Zener-protected
Power MOSFETs developed using
STMicroelectronics' SuperMESH technology,
achieved through optimization of ST's well
established strip-based PowerMESH layout. In
addition to a significant reduction in onresistance, this device is designed to ensure a
high level of dv/dt capability for the most
demanding applications.
SC15010
Table 1.
Device summary
Order codes
Marking
Package
STB9NK60ZT4
B9NK60Z
D2PAK
STP9NK60Z
P9NK60Z
TO-220
STP9NK60ZFP
P9NK60ZFP
TO-220FP
January 2013
This is information on a product in full production.
Doc ID 8799 Rev 3
Packaging
Tube
1/19
www.st.com
19
Contents
Contents
1
Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1
Electrical characteristics (curves)
............................ 7
Test circuits
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Doc ID 8799 Rev 3
Electrical ratings
Electrical ratings
Table 2.
Absolute maximum ratings

Value
Symbol
Parameter
Unit
DPAK, TO-220
TO-220FP
VDS
Drain-source voltage
600
VGS
Gate-source voltage
30
ID
Drain current (continuous) at TC = 25C
7(1)
ID
Drain current (continuous) at TC=100C
4.4
4.4(1)
IDM(2)
Drain current (pulsed)
28
28(1)
PTOT
Total dissipation at TC = 25C
125
30
0.24
W/C
Derating Factor
ESD
dv/dt(3)
VISO
TJ
Tstg
Gate-source human body model (R=1,5 k,

C=100 pF)
Peak diode recovery voltage slope
Insulation withstand voltage (RMS) from all
three leads to external heat sink (t = 1 s,TC =
25 C)
kV
4.5
V/ns
--
Operating junction temperature

Storage temperature
2500
-55 to 150
1. Limited by maximum junction temperature

2. Pulse width limited by safe operating area
3. ISD 7A, di/dt 200A/s,VDD V(BR)DSS, Tj TJMAX
Table 3.
Thermal data
Value
Symbol
Parameter
Unit
DPAK
Rthj-case
Thermal resistance junction-case max
Rthj-amb
Thermal resistance junction-ambient max
Rthj-pcb
Thermal resistance junction-pcb max
(1)
TO-220
TO-220FP
4.2
62.5
30
C/W
C/W
C/W
1. When mounted on minimum footprint
Doc ID 8799 Rev 3
3/19
Electrical ratings
Table 4.
Avalanche characteristics
Symbol
IAR
EAS
Parameter
Avalanche current, repetitive or not-repetitive(1)
Single pulse avalanche energy
(2)
1. Pulse width limited by Tj Max

2. Starting Tj=25 C, ID=IAR, VDD=50 V
4/19
Doc ID 8799 Rev 3
Value
Unit
235
mJ
Electrical characteristics
(TCASE=25C unless otherwise specified)
Table 5.
Symbol
V(BR)DSS
On/off states
Parameter
Test conditions
Drain-source breakdown
voltage VGS= 0
ID = 1 mA
Min.
Typ.
Max.
600
Unit
V
VDS = 600 V,
VDS = 600 V, TC = 125 C
1
50
A
A
Gate body leakage current

(VDS = 0)
VGS = 20 V
10
VGS(th)
Gate threshold voltage
VDS= VGS, ID = 100 A
3.75
4.5
RDS(on)
Static drain-source onresistance
VGS= 10 V, ID= 3.5 A
0.85
0.95
IDSS
Zero gate voltage drain

current (VGS = 0)
IGSS
Table 6.
Symbol
gfs (1)
Ciss
Coss
Crss
Dynamic
Parameter
Qgs
Qgd
Test conditions
Min.
Typ.
Max.
Unit
Forward transconductance
VDS =15 V, ID = 3.5 A
5.3
Input capacitance
Output capacitance
Reverse transfer
capacitance
VDS =25 V, f=1 MHz, VGS=0
1110
135
30
pF
pF
pF
VGS=0, VDS =0 V to 480 V
72
pF
38
7
21
Coss eq(2) Equivalent output

capacitance
Qg
Total gate charge

Gate-source charge
Gate-drain charge
VDD=480 V, ID = 7 A
VGS =10 V
(see Figure 18)
53
nC
nC
nC
1. Pulsed: pulse duration=300s, duty cycle 1.5%

2. Coss eq. is defined as a constant equivalent capacitance giving the same charging time as Coss when VDS
increases from 0 to 80% VDSS
Doc ID 8799 Rev 3
5/19
Table 7.
Symbol
td(on)
tr
td(off)
tf
Table 8.
Symbol
Switching times
Parameter
Test conditions
Min.
Typ.
Max.
Unit
19
17
ns
ns
43
15
ns
ns
Min.
Typ.
Max.
Unit
30
VDD=300 V, ID=3.5 A,
Turn-on delay time

Rise time
RG=4.7 , VGS=10 V
(see Figure 19)
VDD=300 V, ID=3.5 A,
Turn-off delay time

Fall time
RG=4.7 , VGS=10 V
(see Figure 19)
Gate-source zener diode

Parameter
Test conditions
V(BR)GSO Gate-source breakdown voltage IGS= 1 mA, ID=0
The built-in back-to-back Zener diodes have been specifically designed to enhance not only
the devices ESD capability, but also to make them capable of safely absorbing any voltage
transients that may occasionally be applied from gate to source. In this respect, the Zener
voltage is appropriate to achieve efficient and cost-effective protection of device integrity.
The integrated Zener diodes thus eliminate the need for external components.
Table 9.
Symbol
ISD
Source drain diode

Parameter
Test conditions
Typ.
Max.
Unit
Source-drain current
ISDM(1)
Source-drain current (pulsed)
28
VSD(2)
Forward on voltage
ISD=7 A, VGS=0
1.6
Reverse recovery time

Reverse recovery charge
Reverse recovery current
di/dt = 100 A/s,

VDD=30 V, Tj=150 C
trr
Qrr
IRRM
ISD=7 A,
1. Pulse width limited by safe operating area

2. Pulsed: pulse duration=300 s, duty cycle 1.5%
6/19
Min.
Doc ID 8799 Rev 3
480
3.5
14.5
ns
C
A
2.1
Electrical characteristics (curves)
Figure 2.
Safe operating area for DPAK and

TO-220
Figure 3.
Thermal impedance for DPAK and

TO-220
Figure 4.
Safe operating area for TO-220FP
Figure 5.
Thermal impedance for TO-220FP
Figure 6.
Output characterisics
Figure 7.
Transfer characteristics
Doc ID 8799 Rev 3
7/19
Figure 8.
Transconductance
Figure 9.
Static drain-source on-resistance
Figure 10. Gate charge vs gate-source voltage Figure 11. Capacitance variations
Figure 12. Normalized gate threshold voltage

vs temperature
8/19
Figure 13. Normalized on-resistance vs

temperature
Doc ID 8799 Rev 3

Figure 14. Source-drain diode forward
characteristics
Figure 15. Normalized BVDSS vs temperature
Figure 16. Maximum avalanche energy vs

temperature
Doc ID 8799 Rev 3
9/19
Test circuits
Test circuits
Figure 17. Switching times test circuit for

resistive load
Figure 18. Gate charge test circuit
Figure 19. Test circuit for inductive load

Figure 20. Unclamped Inductive load test
switching and diode recovery times
circuit
Figure 21. Unclamped inductive waveform
10/19
Figure 22. Switching time waveform
Doc ID 8799 Rev 3
Package mechanical data

In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK packages, depending on their level of environmental compliance. ECOPACK
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK is an ST trademark.
Doc ID 8799 Rev 3
11/19
Table 10.
DPAK (TO-263) mechanical data

mm
Dim.
Min.
Typ.
4.40
4.60
A1
0.03
0.23
0.70
0.93
b2
1.14
1.70
0.45
0.60
c2
1.23
1.36
8.95
9.35
D1
7.50
10
E1
8.50
10.40
2.54
e1
4.88
5.28
15
15.85
J1
2.49
2.69
2.29
2.79
L1
1.27
1.40
L2
1.30
1.75
R
V2
12/19
Max.
0.4
0
Doc ID 8799 Rev 3
Figure 23. DPAK (TO-263) drawing
0079457_T
Figure 24. DPAK footprint(a)

16.90
12.20
5.08
1.60
3.50
9.75
Footprint
a. All dimension are in millimeters
Doc ID 8799 Rev 3
13/19
Table 11.
TO-220 type A mechanical data

mm
Dim.
Min.
Typ.
4.40
4.60
0.61
0.88
b1
1.14
1.70
0.48
0.70
15.25
15.75
D1
14/19
Max.
1.27
10
10.40
2.40
2.70
e1
4.95
5.15
1.23
1.32
H1
6.20
6.60
J1
2.40
2.72
13
14
L1
3.50
3.93
L20
16.40
L30
28.90
3.75
3.85
2.65
2.95
Doc ID 8799 Rev 3
Figure 25. TO-220 type A drawing
0015988_typeA_Rev_S
Doc ID 8799 Rev 3
15/19
Table 12.
TO-220FP mechanical data

mm
Dim.
Min.
Typ.
4.4
4.6
2.5
2.7
2.5
2.75
0.45
0.7
0.75
F1
1.15
1.70
F2
1.15
1.70
4.95
5.2
G1
2.4
2.7
10
10.4
L2
16/19
Max.
16
L3
28.6
30.6
L4
9.8
10.6
L5
2.9
3.6
L6
15.9
16.4
L7
9.3
Dia
3.2
Doc ID 8799 Rev 3
Figure 26. TO-220FP drawing
7012510_Rev_K_B
Doc ID 8799 Rev 3
17/19
Revision history
Revision history
Table 13.
Document revision history
Date
31-Jan-2013
18/19
Revision
Changes
Minor text changes
The part number STB9NK60Z-1 has been moved to a separate
datasheet
Updated: Section 4: Package mechanical data.
Doc ID 8799 Rev 3
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (ST) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to STs terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN STS TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USERS OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.

Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
2013 STMicroelectronics - All rights reserved

STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 8799 Rev 3
19/19

STB9NK60Z, STP9NK60Z, STP9NK60ZFP

Uploaded by

Copyright:

Available Formats

STB9NK60Z, STP9NK60Z, STP9NK60ZFP

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

STB9NK60Z, STP9NK60Z, STP9NK60ZFP

Uploaded by

Copyright:

Available Formats

STB9NK60Z, STP9NK60Z, STP9NK60ZFP

N-channel 600 V, 0.85 typ., 7 A Zener-protected SuperMESH

Extremely high dv/dt capability

Improved ESD capability

100% avalanche tested

Gate charge minimized

Very low intrinsic capacitances

Internal schematic diagram

Doc ID 8799 Rev 3