Three Point Lighting Tutorial

Back to Main Index.
Adapted & Shortened from
Three-Point Lighting for 3D Renderings
Three lights: the Key Light, Fill Light, and Rim Light (also called
Back Light), are adjusted to achieve the classic Hollywood lighting
scheme called three-point lighting.
Digital Lighting & Rendering

By Jeremy Birn
This GIF Animation shows the role of the 3 lights.
Here's how to set them up in your 3D scenes:
1. Start in Darkness. Make sure there are no default lights, and

there's no global ambience. When you add your first light, there should
be no other light in the scene.
2. Add your Key Light. The Key Light creates the subject's main
illumination, and defines the most visible lighting and shadows. Your
Key Light represents the dominant light source, such as the sun, a
window, or ceiling light - although the Key does not have to be
positioned exactly at this source.
Create a spot light to serve as the Key. From the top view, offset the
Key Light 15 to 45 degrees to the side (to the left or right) of the
camera. From a side view, raise the Key Light above the camera, so
that it hits your subject from about 15 to 45 degrees higher than the
camera angle.
The key light is brighter than any other light illuminating the front of the
subject, is the main shadow-caster in your scene, and casts the
darkest shadows. Specular highlights are triggered by the Key Light.
NOTE: Be sure to stop and do test-renders here. Your "one light"
scene (with just the key light) should have a nice balance and contrast
between light and dark, and shading that uses all of the grays in
between. Your "one light" should look almost like the final rendering,
except that the shadows are pitch black and it has very harsh contrast
- see the GIF animation at the top of this page, while it only has the
Key light visible.
3. Add your Fill Light(s). The Fill Light softens and extends the
illumination provided by the key light, and makes more of the subject
visible. Fill Light can simulate light from the sky (other than the sun),
secondary light sources such as table lamps, or reflected and bounced
light in your scene. With several functions for Fill Lights, you may add
several of them to a scene. Spot lights are the most useful, but point
lights may be used.
From the top view, a Fill Light should come from a generally opposite
angle than the Key - if the Key is on the left, the Fill should be on the
right - but don't make all of your lighting 100% symmetrical! The Fill
can be raised to the subject's height, but should be lower than the Key.
At most, Fill Lights can be about half as bright as your Key (a Key-toFill ratio of 2:1). For more shadowy environments, use only 1/8th the
Key's brightness (a Key-to-Fill ratio of 8:1). If multiple Fills overlap,
their sum still shouldn't compete with the Key.
Shadows from a Fill Light are optional, and often skipped. To simulate
reflected light, tint the Fill color to match colors from the environment.
Fill Lights are sometimes set to be Diffuse-only (set not to cast
specular highlights.)
4. Add Rim Light. The Rim Light (also called Back Light) creates a
bright line around the edge of the object, to help visually separate the
object from the background.
From the top view, add a spot light, and position it behind your subject,
opposite from the camera. From the right view, position the Back Light
above your subject.
Adjust the Rim Light until it gives you a clear, bright outline that
highlights the top or side edge for your subject. Rim Lights can be as
bright as necessary to achieve the glints you want around the hair or
sides of your subject. A Rim Light usually needs to cast shadows.
Often you will need to use light linking to link rim lights only with the
main subject being lit, so that it creates a rim of light around the top or
side of your subject, without affecting the background:
No Back Light (left), Back Light added (right).
That's it. Three-Point Lighting can be a simple starting-point for

lighting just about any subject. By walking through it, this tutorial
introduced 3 of the main visual functions served by lights in your 3D
scenes: Key Light, Fill Light, and Rim Light. In a more complex scene,
there are other types of lights used as well: Practical Lights, Bounce
Lights, Kickers, and Specular Lights, which serve other visual
functions. The book Digital Lighting & Rendering goes into much more
depth about these.
The vocabulary of describing lights by their visual function is something

you can apply in any scene. However, even when you use Key, Fill,
and Rim lights, don't think of three-point lighting as an excuse to light
by formula, or to make every scene look the same. You should begin
each scene by looking at what is motivated, by which kinds of light
would really be in that particular scene. There is usually some
direction from which the light is brightest, and that is where the Key
light should come from. If the object is back-lit, then there may be a
rim, in other cases there isn't one. It is observing the actual colors,
tones, contrast, and direction of real light that actually informs how to
create believable scenes in 3D.
While the original first edition of Digital Lighting & Rendering had a
chapter focused on Three Point Lighting (which was the inspiration for
this tutorial), the new Second Edition de-emphasizes this approach.
Three Point Lighting is still covered in the chapter on Lighting
Creatures and Characters, but it is put into a context of understanding
the different visual functions of lights that are commonly used in
lighting animated characters. By not presenting it first, hopefully
beginning artists won't mistake three point lighting for any kind of a
formula or recipe. If you are trying to create believable lighting that fits
with each unique situation, there's no shortcut to skip studying the
motivations and qualities of real lights that would occur in a particular
scene.
Copyright 2000-2007 Jeremy Birn, 3dRender.com. Adapted & shortened by permission of New Riders Publishing
from [Digital] Lighting & Rendering Edition 2, by Jeremy Birn.

Three Point Lighting Tutorial

Uploaded by

Copyright:

Available Formats

Three Point Lighting Tutorial

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Three Point Lighting Tutorial

Uploaded by

Copyright:

Available Formats

Back to Main Index.

Adapted & Shortened from

Three-Point Lighting for 3D Renderings

Digital Lighting & Rendering

Here's how to set them up in your 3D scenes:

1. Start in Darkness. Make sure there are no default lights, and

No Back Light (left), Back Light added (right).

That's it. Three-Point Lighting can be a simple starting-point for

The vocabulary of describing lights by their visual function is something

You might also like