Autochangeover - 1 BC 2 INCOMERS

mile! Youre at the best WordPress.
com site ever
CATEGORY ARCHIVES: AUTO

CHANGEOVER SCHEME
AUTO CHANGEOVER SCHEME

Posted on March 26, 2013 under Auto changeover scheme
1
2
3
4
5
6
7
Auto changeover scheme

Independent Mode,Manual Mode,Auto Mode,Feeder Requ
General Requirement,
Manual Mode
Manual Mode Tripping conditions
Auto Mode
Additional Points.
1 Comment
ADDITIONAL POINTS.

Additional Points.
If Earth switch or Cable earthing truck & Bus earthing truck is
available, than some additional interlocks shall be provided.
If 4 No Incomer feeders & 1 No Bus coupler are available, than
additional interlocks shall be provided
Additional Interlocks
It will not be possible to OPEN the front DOOR when the circuit
breaker is switched ONin service position.
It will not be possible to rack OUTthe Vacuum Circuit Breaker
trolley from Service to Test position when the breaker is switched
ON
Similarly, it will not be possible to rack INthe Vacuum Circuit

Breaker from Test to Service position when Vacuum Circuit
Breaker is switched ON.
It will not be possible to rack INthe Vacuum Circuit Breaker
when the front Vacuum Circuit Breaker chamber door is open.
(However, a suitable defeat interlock mechanism shall be
provided for emergency purpose.)
It will be only possible to switch ONthe earthling switch if
provided, when the withdrawable truck is in Test position.
It will not be possible to rack INVacuum Circuit Breaker from
Test to service position, in case the earthing switch is ON.
Earthing trolleys can be also supplied. Electro-magnetic interlocks
to be provided on earthing trolley for incomers and ties feeders.
It will be not possible to switch ONthe circuit breaker when
ISOLATOR is Open.
It will be not possible to OPEN the isolator when circuit breaker is
ON.
It will be not possible to CLOSEthe earth switch when circuit
breaker is ON.
It will be not possible to CLOSEthe earth switch when isolator is
CLOSED.
Similarly, it will be not possible to CLOSEthe circuit breaker &
isolator when earth switch is ON.
Schematic diagram of interlocks
Go Back
Leave a comment
AUTO MODE

Closing conditions-B/C
When fault (U/V) on bus side-A Than it checks,
Selector switch is on Auto Mode.
Incomer-1 off & no fault trip.
Incomer-2 On & in service.
Bus PT-1 unhealthy.
Bus PT-2 healthy.
This conditions are satisfy than contactor will be pick up & close
the breaker.
When fault (U/V) on bus side-B Than it checks,
Selector switch is on Auto Mode.
Incomer-2 off & no fault trip.
Incomer-1 On & in service.
Bus PT-2 unhealthy.
Bus PT-1 healthy.
This conditions are satisfy than contactor will be pick up & close
the breaker.
Closing For B/C-Manual mode

Go to Next page
Go Back
Leave a comment
MANUAL MODE
TRIPPING CONDITIONS
Manual Mode Tripping conditions-I/C-2
Trip selector switch on I/C-2
Incomer-1 On & in Service
Bus coupler On & in Service
After some time delay, I/C-2 will be trip.
Tripping For I/C-2-Manual mode
Manual Mode Closing conditions-B/C

Mode selector switch in Manual mode
Supply is Synchronize
Manual Mode Tripping conditions-B/C

Trip selector switch on B/C
If in any condition I/C-1 & I/C-2 become OFF, Then B/C will be OFF
Tripping For B/C-Manual mode
Go to Next page
Go Back
Leave a comment
MANUAL MODE

Manual Mode
Closing conditions-I/C-1
Closing For I/C-1-Manual mode

Manual Mode
Tripping conditions-I/C-1
Tripping For I/C-1-Manual mode
Manual Mode
Closing For I/C-2-Manual mode
Go to Next page
Go Back
Leave a comment
GENERAL REQUIREMENT,
General Requirement
Bus Pt for measuring Bus voltage & checking bus is healthy or
unhealthy.
Line Pt for measuring Line voltage & Synchronizing between two
sources.
Numerical relays with maximum BI-BO & breaker with maximum aux.
contacts.
If synchronizing is required, then synchronizing function should be

available in numerical relay of bus coupler.
General Schematic Diagram
General Singe Line Diagram
Independent Mode
Mode selector switch in independent mode
Bus PT-1 Unhealthy
Incomer-2 Off & no fault trip
Bus coupler Off & no fault trip
Closing For incomer-1 Ind. mode
Independent Mode
Bus PT-2 Unhealthy
Bus coupler Off & no fault trip
Closing For incomer-2-Ind. mode
Independent Mode
Bus PT-1 Unhealthy
Bus PT-2 Unhealthy
For Bus Coupler-Ind. mode
Go to Next page
Go Back
Leave a comment
INDEPENDENT MODE,MANUAL
MODE,AUTO
MODE,FEEDER REQUIRED
In this mode, Two Breakers can close at the same time.

For e.g.:-
INCOMER-1
ON
INCOMER-2
ON
BUSCOUPLER
OFF
INCOMER-1
ON
INCOMER-2
OFF
BUSCOUPLER
ON
INCOMER-1
OFF
INCOMER-2
ON
BUSCOUPLER
ON
Manual Mode
In this mode, When supply is Synchronize, Then Three Breakers
can close at the same time. But after some time delay, one
breaker will be Trip by using Trip Selector Switch.
For e.g.:I/C-1 & B/C are ON & if I/C-2 ON than I/C-1 will be trip after some time
delay. (if Trip selector switch is on I/C-1)
Auto Mode
This mode is only for Bus coupler.
If two incomer is On & Bus coupler is Off. If one incomer trip due
to under voltage. At that time B/C is On automatically.
Feeder Required
Incomer-1 with Line Pt-1
Incomer-2 with Line Pt-2
Bus Coupler
Bus Pt-1
Bus Pt-2
Outgoing Feeders
Go to Next page
Go Back
Leave a comment
AUTO CHANGEOVER SCHEME

What is Auto Change Over?

Load can be transfer from one Bus to another Bus by using Auto
Change Over Scheme.
It means, within specific conditions, load can be transferred on
another bus by automatically ON or OFF the breakers, without
disturbing any load.
Different Mode for changeover
Independent Mode
Manual Mode / Synchronizing Mode
Auto Mode
Blackout Condition
Different Switches for changeover
Mode Selector Switch: This switch is on Bus coupler.
This switch is 3 pole, 3 position switch.
Three positions are,
(1) Auto
(2) Independent
(3) Manual
Trip Selector Switch: This switch is on Bus coupler.

This switch is 3 pole, 3 position switch.
Three positions are,
(1) Incomer-1 trip
(2) Incomer-2 trip
(3) Bus coupler trip

Autochangeover - 1 BC 2 INCOMERS

Uploaded by

Copyright:

Available Formats

Autochangeover - 1 BC 2 INCOMERS

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Autochangeover - 1 BC 2 INCOMERS

Uploaded by

Copyright:

Available Formats

mile! Youre at the best WordPress.

com site ever

CATEGORY ARCHIVES: AUTO

AUTO CHANGEOVER SCHEME

Auto changeover scheme

Posted on March 26, 2013 under Auto changeover scheme

Similarly, it will not be possible to rack INthe Vacuum Circuit

Schematic diagram of interlocks

Posted on March 26, 2013 under Auto changeover scheme

Closing For B/C-Manual mode

Tripping For I/C-2-Manual mode

Manual Mode Closing conditions-B/C

Closing For B/C-Manual mode

Manual Mode Tripping conditions-B/C

Tripping For B/C-Manual mode

Posted on March 26, 2013 under Auto changeover scheme

Closing For I/C-1-Manual mode

Tripping For I/C-1-Manual mode

Closing For I/C-2-Manual mode

If synchronizing is required, then synchronizing function should be

General Singe Line Diagram

Closing For incomer-1 Ind. mode

In this mode, Two Breakers can close at the same time.

AUTO CHANGEOVER SCHEME

What is Auto Change Over?

Trip Selector Switch: This switch is on Bus coupler.

You might also like