www.studymafia.

org

A
Seminar report
On

Smart Dust
Submitted in partial fulfillment of the requirement for the award of degree
of Electronics

SUBMITTED TO:

SUBMITTED BY:

www.studymafia.org

www.studymafia.org

www.studymafia.org

Preface
I have made this report file on the topic Smart Dust; I have tried my best to elucidate
all the relevant detail to the topic to be included in the report. While in the beginning I
have tried to give a general view about this topic.
My efforts and wholehearted co-corporation of each and everyone has ended on a
successful note. I express my sincere gratitude to ..who assisting me
throughout the preparation of this topic. I thank him for providing me the
reinforcement, confidence and most importantly the track for the topic whenever I
needed it.

www.studymafia.org

Acknowledgement
I would like to thank respected Mr.. and Mr. ..for giving me such a
wonderful opportunity to expand my knowledge for my own branch and giving me
guidelines to present a seminar report. It helped me a lot to realize of what we study for.
Secondly, I would like to thank my parents who patiently helped me as i went through
my work and helped to modify and eliminate some of the irrelevant or un-necessary
stuffs.
Thirdly, I would like to thank my friends who helped me to make my work more
organized and well-stacked till the end.
Next, I would thank Microsoft for developing such a wonderful tool like MS Word. It
helped my work a lot to remain error-free.
Last but clearly not the least, I would thank The Almighty for giving me strength to
complete my report on time.

www.studymafia.org

INTRODUCTION
Smart dust is a tiny dust size device with extra-ordinary capabilities. Smart dust
combines sensing, computing, wireless communication capabilities and autonomous
power supply within volume of only few millimeters and that too at low cost. These
devices are proposed to be so small and light in weight that they can remain suspended
in the environment like an ordinary dust particle.
These properties of Smart Dust will render it useful in monitoring real world
phenomenon without disturbing the original process to an observable extends. Presently
the achievable size of Smart Dust is about 5mm cube, but we hope that it will
eventually be as small as a speck of dust.
Individual sensors of smart dust are often referred to as motes because of their
small size. These devices are also known as MEMS, which stands for micro electromechanical sensors.

www.studymafia.org

WHAT IS A SMART DUST?

Autonomous sensing and communication in a cubic millimeter
Berkeleys Smart Dust project, led by Professors Pister and Kahn,
explores the limits on size and power consumption in autonomous sensor
nodes. Size reduction is paramount, to make the nodes as inexpensive and
easy-to-deploy as possible. The research team is confident that they can
incorporate the requisite sensing, communication, and computing hardware,
along with a power supply, in a volume no more than a few cubic
millimeters, while still achieving impressive performance in terms of sensor
functionality and communications capability. These millimeter-scale nodes
are called Smart Dust. It is certainly within the realm of possibility that
future prototypes of Smart Dust could be small enough to remain suspended
in air, buoyed by air currents, sensing and communicating for hours or days
on end.
'Smart dust' sensor-laden networked computer nodes that are
just cubic millimetres in volume. The smart dust project envisions a
complete sensor network node, including power supply, processor, sensor
and communications mechanisms, in a single cubic millimetre. .Smart dust
motes could run for years , given that a cubic millimetre battery can store 1J
and could be backed up with a solar cell or vibrational energy source
The goal of the Smart Dust project is to build a millimeter-scale
sensing and communication platform for a massively distributed sensor
network. This device will be around the size of a grain of sand and will
contain sensors, computational ability, bi-directional wireless
communications, and a power supply. Smart dust consists of series of
circuit and micro-electro-mechanical systems (MEMS) designs to cast those
functions into custom silicon. Microelectromechanical systems (MEMS)
consist of extremely tiny mechanical elements, often integrated together

www.studymafia.org
with electronic circuitry.

THE MEMS TECHNOLOGY IN SMART DUST

Smart

dust

requires

mainly

revolutionary

advances

in

miniaturization, integration & energy management. Hence designers have

used MEMS technology to build small sensors, optical communication
components, and power supplies. Microelectro mechanical systems consists
of extremely tiny mechanical elements, often integrated together with
electronic circuitory. They are measured in micrometers, that is millions of
a meter. They are made in a similar fashion as computer chips. The
advantage of this manufacturing process is not simply that small structures
can be achieved but also that thousands or even millions of system elements
can be fabricated simultaneously. This allows systems to be both highly
complex and extremely low-cost.

Micro-Electro-Mechanical Systems (MEMS) is the integration of

mechanical elements, sensors, actuators, and electronics on a common
silicon substrate through microfabrication technology. While the electronics
are fabricated using integrated circuit (IC) process sequences (e.g., CMOS,
Bipolar processes), the micromechanical components are fabricated using
compatible "micromachining" processes that selectively etch away parts of
the silicon wafer or add new structural layers to form the mechanical and
electromechanical devices. MEMS realizes a complete System On chip
technology.

Microelectronic integrated circuits can be thought of as the "brains"

of a system and allow microsystems to sense and control the environment.

www.studymafia.org
Sensors gather information from the environment through measuring
mechanical,

thermal,

biological,

chemical,

optical,

and

magnetic

phenomena. The electronics then process the information derived from the
sensors and through some decision making capability direct the actuators to
respond by moving, positioning, regulating, and filtering, thereby
controlling the environment for some desired purpose. Because MEMS
devices are manufactured using batch fabrication techniques similar to
those used for integrated circuits, unprecedented levels of functionality,
reliability, and sophistication can be placed on a small silicon chip at a
relatively low cost. The deep insight of MEMS is as a new manufacturing
technology, a way of making complex electromechanical systems using
batch fabrication techniques similar to those used for integrated circuits,
and uniting these electromechanical elements together with electronics.
Historically, sensors and actuators are the most costly and unreliable part of
a sensor-actuator-electronics system. MEMS technology allows these
complex electromechanical systems to be manufactured using batch
fabrication techniques, increasing the reliability of the sensors and actuators
to equal that of integrated circuits. The performance of MEMS devices and
systems is expected to be superior to macro scale components and systems,
the price is predicted to be much lower.

www.studymafia.org

www.studymafia.org

SMART DUST TECHNOLOGY

Integrated into a single package are :-

1.

MEMS sensors

2.

MEMS beam steering mirror for active optical transmission

3.

MEMS corner cube retroreflector for passive optical transmission

4.

An optical receiver

5.

Signal processing and control circuitory

6.

A power source based on thick film batteries and solar cells

This remarkable package has the ability to sense and communicate and
is self powered. A major challenge is to incorporate all these functions
while maintaining very low power consumption.

Sensors collect information from the environment such as light , sound,

temperature ,chemical composition etc

Smart dust employs 2 types of transmission schemes:-passive transmission

using corner cube retro reflector to transmit to base stations and active
transmission using a laser diode & steerable mirrors for mote to mote
communication.

The photo diode allows optical data reception

Signal processing & control circuitry consists of analog I/O ,DSPs to
control &process the incoming data

The power system consists of a thick film battery, a solar cell with a charge
integrating capacitor for a period of darkness.

www.studymafia.org

OPERATION OF THE MOTE

The Smart Dust mote is run by a microcontroller that not only
determines the tasks performed by the mote, but controls power to the
various components of the system to conserve energy. Periodically the
microcontroller gets a reading from one of the sensors, which measure one
of a number of physical or chemical stimuli such as temperature, ambient
light, vibration, acceleration, or air pressure, processes the data, and stores
it in memory. It also occasionally turns on the optical receiver to see if
anyone is trying to communicate with it. This communication may include
new programs or messages from other motes. In response to a message or
upon its own initiative the microcontroller will use the corner cube retro
reflector or laser to transmit sensor data or a message to a base station or
another mote.

The primary constraint in the design of the Smart Dust motes is volume,
which in turn puts a severe constraint on energy since we do not have much
room for batteries or large solar cells. Thus, the motes must operate
efficiently and conserve energy whenever possible. Most of the time, the
majority of the mote is powered off with only a clock and a few timers
running. When a timer expires, it powers up a part of the mote to carry out a
job, then powers off. A few of the timers control the sensors that measure
one of a number of physical or chemical stimuli such as temperature,
ambient light, vibration, acceleration, or air pressure. When one of these
timers expires, it powers up the corresponding sensor, takes a sample, and
converts it to a digital word. If the data is interesting, it may either be stored

www.studymafia.org
directly in the SRAM or the microcontroller is powered up to perform more
complex operations with it. When this task is complete, everything is again
powered down and the timer begins counting again.

Another timer controls the receiver. When that timer expires, the
receiver powers up and looks for an incoming packet. If it doesn't see one
after a certain length of time, it is powered down again. The mote can
receive several types of packets, including ones that are new program code
that is stored in the program memory. This allows the user to change the
behavior of the mote remotely. Packets may also include messages from the
base station or other motes. When one of these is received, the
microcontroller is powered up and used to interpret the contents of the
message. The message may tell the mote to do something in particular, or it
may be a message that is just being passed from one mote to another on its
way to a particular destination. In response to a message or to another timer
expiring, the microcontroller will assemble a packet containing sensor data
or a message and transmit it using either the corner cube retroreflector or
the laser diode, depending on which it has. The laser diode contains the
onboard laser which sends signals to the base station by blinking on and off.
The corner cube retroreflector , transmits information just by moving a
mirror and thus changing the reflection of a laser beam from the base
station.

This technique is substantially more energy efficient than actually

generating some radiation. With the laser diode and a set of beam scanning
mirrors, we can transmit data in any direction desired, allowing the mote to
communicate with other Smart Dust motes.

www.studymafia.org

COMMUNICATING WITH A SMART DUST

COMMUNICATING FROM A GRAIN OF SAND
Smart Dusts full potential can only be attained when the sensor
nodes communicate with one another or with a central base station.
Wireless communication facilitates simultaneous data collection from
thousands of sensors. There are several options for communicating to and
from a cubic-millimeter computer.
Radio-frequency and optical communications each have their
strengths and weaknesses. Radio-frequency communication is well understood, but currently requires minimum power levels in the multiple
milliwatt range due to analog mixers, filters, and oscillators. If whisker-thin
antennas of centimeter length can be accepted as a part of a dust mote, then
reasonably

efficient

antennas

can

be

made

for

radio-frequency

communication. While the smallest complete radios are still on the order of
a few hundred cubic millimeters, there is active work in the industry to
produce cubic-millimeter radios.
Moreover RF techniques cannot be used because of the following
disadvantages: 1. Dust motes offer very limited space for antennas, thereby demanding
extremely

short

wavelength

(high

frequency

transmission).

Communication in this regime is not currently compatible with low

power operation of the smart dust.
2. Furthermore radio transceivers are relatively complex circuits making
it difficult to reduce their power consumption to required microwatt
levels.

www.studymafia.org
3. They require modulation, band pass filtering and demodulation
circuitory.

So an attractive alternative is to employ free space optical

transmission. Studies have shown that when a line of sight path is available
, well defined free space optical links require significantly lower energy per
bit than their RF counter paths.

There are several reasons for power advantage of optical links.

1. Optical transceivers require only simple base band analog and digital
circuitory.
2. No modulators, active band pass filters or demodulators are needed.
3. The short wavelength of visible or near infra red light (of the order of 1
micron) makes it possible for a millimeter scale device to emit a
narrow beam (ie, high antenna gain can be achieved).

As another consequence of this short wavelength, a Base Station

Transceiver (BTS) equipped with a compact imaging receiver can decode
the simultaneous transmissions from a large number of dust motes from
different locations within the receiver field of view, which is a form of
space division multiplexing. Successful decoding of these simultaneous
transmissions requires that dust motes not block one anothers line of sight
to the BTS. Such blockage is unlikely in view of dust motes small size.

Semiconductor lasers and diode receivers are intrinsically small,

and the corresponding transmission and detection circuitry for on/off keyed
optical communication is more amenable to low-power operation than most

www.studymafia.org
radio schema. Perhaps most important, optical power can be collimated in
tight beams even from small apertures. Diffraction enforces a fundamental
limit on the divergence of a beam, whether it comes from an antenna or a
lens. Laser pointers are cheap examples of milliradian collimation from a
millimeter aperture. To get similar collimation for a 1-GHz radio-frequency
signal would require an antenna 100 meters across, due to the difference in
wavelength of the two transmissions. As a result, optical transmitters of
millimeter size can get antenna gains of one million or more, while
similarly sized radio frequency antennas are doomed by physics to be
mostly isotropic.

Collimated optical communication has two major drawbacks. Line

of sight is required for all but the shortest distances, and narrow beams
imply the need for accurate pointing. Of these, MEMS technology and
clever algorithms can solve the pointing accuracy, but an optical transmitter
under a leaf or in a shirt pocket is of little use to anyone. We have chosen to
explore optical communication in some depth due to the potential for
extreme low-power communication.

www.studymafia.org

OPTICAL COMMUNICATIONS
We have explored two approaches to optical communications: passive
reflective systems and active-steered laser systems. In a passive
communication system, the dust mote does not require an onboard light
source. Instead, a special configuration of mirrors can either reflect or not
reflect light to a remote source.

Passive reflective systems

The passive reflective communication is obtained by a special
device called CCR (Corner cube retro reflector) consists of three mutually
orthogonal mirrors. Light enters the CCR, bounces off each of the three
mirrors, and is reflected back parallel to the direction it entered. In the
MEMS version, the device has one mirror mounted on a spring at an angle
slightly askew from perpendicularity to the other mirrors.

In this position, because the light entering the CCR does not return
along the same entry path, little light returns to the sourcea digital 0.
Applying voltage between this mirror and an electrode beneath it causes the
mirror to shift to a position perpendicular to other mirrors, thus causing the
light entering the CCR to return to its sourcea digital 1. The mirrors low
mass allows the CCR to switch between these two states up to a thousand
times per second, using less than a nanojoule per 0
transition, on the other hand, is practically free because dumping the charge
stored on the electrode to the ground requires almost no energy. Our latest
Smart Dust device is a 63-mm3 autonomous bidirectional communication

www.studymafia.org
mote that receives an optical signal, generates a pseudorandom sequence
based on this signal to emulate sensor data, and then optically transmits the
result. The system contains a micromachined corner-cube reflector, a 0.078mm3 CMOS chip that draws 17 microwatts, and a hearing aid battery. In
addition to a battery based operation, we have also powered the device
using a 2-mm2 solar cell. This mote demonstrates Smart Dusts essential
concepts, such as optical data transmission, data processing, energy
management, miniaturization, and system integration.

A passive communication system suffers several limitations.

Unable to communicate with each other, motes rely on a central station
equipped with a light source to send and receive data from other motes. If a
given mote does have a clear line of sight to the central station, that mote
will be isolated from the network. Also, because the CCR reflects only a
small fraction of the light emitted from the base station, this systems range
cannot easily extend beyond 1 kilometer. To circumvent these limitations,
dust motes must be active and have their own onboard light source.

Active-steered laser systems

For

mote-to-mote

communication,

an

active-steered

laser

communication system uses an onboard light source to send a tightly

collimated light beam toward an intended receiver. Steered laser
communication has the advantage of high power density; for example, a 1milliwatt laser radiating into 1 milliradian (3.4 arcseconds) has a density of
approximately 318 kilowatts per steradian (there are 4 steradians in a
sphere), as opposed to a 100-watt lightbulb that radiates 8 watts per
steradian isotropically. A Smart Dust motes emitted beam would have a

www.studymafia.org
divergence of approximately 1 milliradian, permitting communication over
enormous distances using milliwatts of power. Each mote must carefully
weigh the needs to sense, compute, communicate, and evaluate its energy
reserve status before allocating precious nanojoules of energy to turn on its
transmitter or receiver. Because these motes spend most of their time
sleeping, with their receivers turned off, scheduling a common awake time
across the network is difficult. If motes dont wake up in a synchronized
manner, a highly dynamic network topology and large packet latency result.
Using burstmode communication, in which the laser operates at up to
several tens of megabits per second for a few milliseconds, provides the
most energy-efficient way to schedule this network. This procedure
minimizes the motes duty cycle and better utilizes its energy reserves. The
steered agile laser transmitter consists of a semiconductor diode laser
coupled with a collimating lens and MEMS beam-steering optics based on a
two degree-of-freedom silicon micromirror.

This system integrates all

optical components into an active 8-mm3 volume as the figure shows

www.studymafia.org
CORNER CUBE RETROREFLECTOR
These MEMS structure makes it possible for dust motes to use
passive optical transmission techniques ie, to transmit modulated optical
signals without supplying any optical power. It comprises of three mutually
perpendicular mirrors of gold-coated polysilicon. The CCR has the property
that any incident ray of light is reflected back to the source (provided that it
is incident within a certain range of angles centered about the cubes body
diagonal).If one of the mirrors is misaligned , this retro reflection property
is spoiled. The micro fabricated CCR contains an electrostatic actuator that
can deflect one of the mirrors at kilohertz rate. It has been demonstrated
that a CCR illuminated by an external light source can transmit back a
modulated signal at kilobits per second. Since the dust mote itself does not
emit light , passive transmitter consumes little power. Using a
microfabricated CCR, data transmission at a bit rate upto 1 kilobit per
second and upto a range of 150 mts ,using a 5 milliwattt illuminating laser
is possible.

It should be emphasized that CCR based passive optical links

require an uninterrupted line of sight. The CCR based transmitter is highly
directional. A CCR can transmit to the BTS only when the CCR body
diagonal happens to point directly towards the BTS, within a few tens of
degrees. A passive transmitter can be made more omnidirectional by
employing several CCRs ,oriented in different directions , at the expense of
increased dust mote size.

www.studymafia.org

The figure illustrates free space optical network utilizing the CCR
based passive uplink. The BTS contains a laser whose beam illuminates an
area containing dust motes. This beam can be modulated with downlink
data including commands to wake up and query the dust motes. When the
illuminating beam is not modulated , the dust motes can use their CCRs to
transmit uplink data back to the base station. A high frame rate CCD video
camera at the BTS sees the CCR signals as lights blinking on and off. It
decodes these blinking images to yield the uplink data. Analysis show that
this uplink scheme achieves several kilobits per second over hundreds of
metres in full sunlight. At night ,in clear ,still air ,the range should extend to
several kilometres. Because the camera uses an imaging process to separate
the simultaneous transmissions from dust motes at different locations, we
say it uses space division multiplexing. The ability for a video camera to
resolve these transmissions is the consequence of the short wavelength of
visible or near infra red light. This does not require any coordination among
the dust motes.

ACTIVE OPTICAL TRANSMITTERS

www.studymafia.org
When the application requires dust motes to use active optical
transmitters , MEMS technology can be used to assemble a semiconductor
laser, a collimating lens, and a beam steering micro mirror. Active
transmitters make possible peer to peer communication between dust motes,
provided there exists a line of path of sight between them. Power
consumption imposes a trade off between bandwidth and range. The dust
motes can communicate over long distances at low data rates or higher bit
rates over shorter distances. The relatively higher power consumption of
semiconductor lasers dictates that these active transmitters be used for short
duration burst mode communication only. Sensor network using active dust
mote transmitters will require some protocol for dust motes to aim their
beams towards the receiving parties.

www.studymafia.org

LISTENING TO A DUST FIELD

Many

Smart

Dust

applications

rely

on

direct

optical

communication from an entire field of dust motes to one or more base

stations. These base stations must therefore be able to receive a volume of
simultaneous optical transmissions. Further, communication must be
possible outdoors in bright sunlight which has an intensity of approximately
1 kilowatt per square meter, although the dust motes each transmit
information with a few milliwatts of power. Using a narrow-band optical
filter to eliminate all sunlight except the portion near the light frequency
used for communication can partially solve this second problem, but the
ambient optical power often remains much stronger than the received signal
power.

Advantages of imaging receivers

As with the transmitter, the short wavelength of optical
transmissions compared with radio frequency overcomes both challenges.
Light from a large field of view field can be focused into an image, as in
our eyes or in a camera. Imaging receivers utilize this to analyze different
portions of the image separately to process simultaneous transmissions from
different angles. This method of distinguishing transmissions based on their
originating location is referred to as space division multiple access
(SDMA). In contrast, most radio-frequency antennas receive all incident
radio power in a single signal, which requires using additional tactics, such
as frequency tuning or code division multiple access (CDMA), to separate
simultaneous transmissions.

www.studymafia.org

Imaging receivers also offer the advantage of dramatically

decreasing the ratio of ambient optical power to received signal
power.Ideally, the imaging receiver will focus all of the received power
from a single transmission onto a single photodetector. If the receiver has
an n

n array of pixels, then the ambient light that each pixel receives is

reduced by a factor n2 compared with a nonimaging receiver.

Video camera.
A video camera is a straightforward implementation of an imaging
receiver. If each member in a colony of Smart Dust motes flashes its own
signal at a rate of a few bits per second, then each transmitter will appear in
the video stream at a different location in the image. Using a high-speed

www.studymafia.org
camera and a dedicated digital signal processor to process the video signal
achieves higher data rates. With modern cameras and DSPs, processing
video at about 1,000 frames per second should be feasible. This would
allow communication at a few hundred bits per second, which is acceptable
for many applications. An alternative receiver architecture provides a more
elegant solution at much higher data rates, avoiding the need for
computationally intensive video processing and very high speed cameras.
Integrating an imaging receiver onto a single microchip imposes severe
constraints in silicon area and power consumption per pixel. Only recently
have continuing reductions in transistor size allowed for sufficient
reductions in circuit area and power consumption to achieve this level of
integration.

www.studymafia.org

CORE FUNCTIONALITY SPECIFICATION

Choose the case of military base monitoring wherein on the order
of a thousand Smart Dust motes are deployed outside a base by a micro air
vehicle to monitor vehicle movement. The motes can be used to determine
when vehicles were moving, what type of vehicle it was, and possibly how
fast it was travelling. The motes may contain sensors for vibration, sound,
light, IR, temperature, and magnetization. CCRs will be used for
transmission, so communication will only be between a base station and the
motes, not between motes. A typical operation for this scenario would be to
acquire data, store it for a day or two, then upload the data after being
interrogated with a laser. However, to really see what functionality the
architecture needed to provide and how much reconfigurability would be
necessary, an exhaustive list of the potential activities in this scenario was
made. The operations that the mote must perform can be broken down into
two categories: those that provoke an immediate action and those that
reconfigure the mote to affect future behavior.

Proposed Architecture
Looking through the functional specifications for the core, we
realized that each operation is regulated by a timed event; hence a bank of
timers forms the basis of the architecture. For minimum energy, a direct
mapping of a particular function into hardware is generally best, but from
the list of specifications it was clear that a certain amount of
reconfigurability would be necessary. Thus, the timers enable setup
memories that configure functional blocks into data paths that provide only

www.studymafia.org
the capabilities necessary for that event. These paths are data-driven so that
functional blocks are only powered up when their inputs are ready,
minimizing standby power and glitching. A block diagram of this new
architecture is shown in the figure

The next figure details a section of the timer bank and setup
memory. The timer is loaded from the timer value memory, setting its
period. When the timer expires, it enables setupmemory 1, which configures
the data path to perform the desired function. When the data path has
finished its operation, setup memory 1 will release its configuration and
y
restarted or setup memory 2 can be enabled.

Setup memory 2 will then configure the data path for another
operation, thus facilitating multiple operations per timer event. Additional
setup memory can be added for more involved sequences. Memory holds
certain timer-independent configuration bits, such as timer enables. The
sensor registers are used to store previous sensor readings to use in
computing data changes. Various computation blocks can be included in the
data path, such as an adder, comparator, and FFT unit.

www.studymafia.org

Multiple timer periods are desirable for several situations. For

example, one might want to sample a sensor at a slow rate until an
interesting signal is detected. At that point, the sampling rate should
increase. In addition, the motes might be deployed without anyone coming
back to talk to them for a day, so it would be desirable to be able to set the
receiver wake-up timer to not wake-up for 24 hours, but then it should
decrease the period dramatically to 10s of seconds in case one doesnt
make it back to talk to the mote at exactly the right time. The proposed
architecture facilitates this by providing multiple timer values that can be
loaded into the timer depending on the results of the data path computation.

Another feature of this architecture is energy-driven operation

modes. An energy-monitoring unit selects between multiple banks of setup
memory and timer values depending on the current level of the energy
stores. Each bank can have different timer periods and algorithms to control
energy expenditure. Two types of packets can be sent to the mote,
corresponding to the two types of operations. Immediate mode operations

www.studymafia.org
use the packet body to configure the data path right away. Reconfiguration
operations load the packet body into the setup memory for future
configuration.

The following figure shows the functional blocks included in the

reconfigurable data path.

For the communications back end, there is a data recovery block,

timing recovery block, FIR filter, packet encoder that does bits stuffing and
adds the flag byte, packet decoder that does bit unstuffing, CRC block, and
a FIFO. Incoming packets are stored in the FIFO until the CRC can be
verified, at which point the packet body will be used as described above.
The global memory holds certain timer-independent configuration bits,
such as timer enables. The sensor registers are used to store previous sensor
readings to use in computing data changes. Various computation blocks can
be included in the data path, such as an adder, comparator, and FFT unit.

www.studymafia.org

All of the functional units in the data path are data driven. The
setup memory only powers up and enables the first set of units that are
needed, such as the sensor and ADC. Once these units have done their job,
they assert a done signal that is routed, based on the configuration memory,
to the next unit, such as the adder, and powers it up and enables it.
Likewise, when this unit has finished its job, it will power up and enable the
next device in the chain. The last unit in the path will cause the timer to
reload its value and cause the setup memory to stop configuring the data
path. The advantages of this data driven technique include minimizing the
standby power by keeping components powered down until exactly when
they are needed, and ensuring that the inputs are stable before the next
device is powered up, which minimizes glitches. It is significant to note that
since this architecture does not use shared busses as in traditional
microcontrollers, the functional components can be configured for certain
parallel operations. For example, a sensor reading could be both stored in
SRAM and transmitted with the CCR, although this is not necessarily a
desirable capability.

www.studymafia.org

PERFORMING A TASK

Figure 5 delineates the operation of the architecture by showing

the configuration for one of the most common tasks, acquiring sensor data,
checking if it has changed more than a threshold value, then storing the
result to memory. One potential hazard of this architecture is that the done
signals can glitch as the blocks are powered up, which would provide a
false trigger to the next stage. A second issue is that despite the fact that the
blocks are powered down, the internal nodes do not discharge immediately.
An advantage of this is that less charge will be needed when the block is
powered up again. However, this stored charge will also allow the block to
continue to drive its outputs despite being powered down, so the outputs
will generally need tri-state buffers. These hazards will require some extra
work at the circuit level to make this architecture work.
Hspice simulations were used simulations were used to determine
the power and energy consumptions of some of the blocks to study the
feasibility of the proposed architecture. The preliminary results of Hspice

www.studymafia.org
simulations show that it is possible to achieve atleast two orders of
magnitude lower energy consumption, with this proposed architecture.

MAJOR CHALLENGES
1. To incorporate all these functions while maintaining a low power
consumption
2. Maximising operating life given the limited volume of energy storage
3. The functionality can be achieved only if the total power consumption
is limited to microwatt levels.
4. An unbroken line of sight of path should be available for free space
optical links.

www.studymafia.org

APPLICATIONS
Not only does the Smart Dust remain suspended in the air for hours, the air currents can
also move them in the direction of flow. It is very hard to detect the presence of the
Smart Dust and it is even harder to get rid of them once deployed. Moreover it does not
cost much so can be densely deployed. Due to the above-mentioned features, Smart
Dust can be used in varied application fields. These are as follows:
1) Environmental protection (identification and monitoring of pollution).
2) Habitat monitoring (observing the behavior of the animals in there natural
habitat).
3) Military application (monitoring activities in inaccessible areas, accompany
soldiers and alert them to any poisons or dangerous biological substances in the
air).
4) Indoor/Outdoor Environmental Monitoring
5) Security and Tracking
6) Health and Wellness Monitoring (enter human bodies and check for
physiological problems)
7) Power Monitoring
8) Inventory Location Awareness
9) Factory and Process Automation
10) Seismic and Structural Monitoring
11) Monitor traffic and redirecting it

www.studymafia.org

HOW FAR THEY HAVE BEEN IMPLEMENTED

1. The optical receiver for the smart dust project is being developed. The
receiver senses incoming laser transmissions at up to 1Mbit/s, for a
power consumption of 12W. Although this is too high for continuous
use in smart dust, it is a reasonable figure for the download of small
amounts of data such as a 1Kbit program.
2. For data transmission, the team is using corner cube retro-reflectors
(CCRs) built using MEMS techniques. CCRs are produced by placing
three mirrors at right angles to each other to form the corner of a box
that has been silvered inside.
The key property of a CCR is that light entering it is reflected back
along the path it entered on. For the smart dust system, the CCR is
being built on a MEMS process with the two vertical sides being
assembled by hand. When a light is shone into the CCR, it reflects
back to the sending position. By modulating the position of one of the
mirrors, the reflected beam can be modulated, producing a low-energy
passive transmission.
3. The analog-digital convertor (ADC) the 8bit ADC, has so far
demonstrated with an input range of 1V, equal to the power supply,
and a 70kHz sampling rate. The converter draws 1.8W when
sampling at that rate, or 27pJ for an 8bit sample.
4. The latest smart dust mote, with a volume of just 16cu mm, has been
tested. It takes samples from a photo-detector, transmits their values
with the CCR and runs off solar cells. So smart dust is on the way.

www.studymafia.org

SUMMARY
Smart dust is made up of thousands of sand-grain-sized sensors
that can measure ambient light and temperature. The sensors -- each one is
called a "mote" -- have wireless communications devices attached to them,
and if you put a bunch of them near each other, they'll network themselves
automatically.

These sensors, which would cost pennies each if mass-produced,

could be plastered all over office buildings and homes. Each room in an
office building might have a hundred or even a thousand light- and
temperature-sensing motes, all of which would tie into a central computer
that regulates energy usage in the building.

Taken together, the motes would constitute a huge sensor network

of smart dust, a network that would give engineers insight into how energy
is used and how it can be conserved. In a dust-enabled building, computers
would turn off lights and climate control in empty rooms. During peak
energy usage times, air conditioners that cool servers -- which drain a lot of
the tech world's power -- would be automatically shut off, and then turned
on again if the servers get too hot. Thus it can very lead to worlds energy
conservation solutions.

www.studymafia.org

REFERENCES

1. P.B.Chu , KSJ Pister optical communication using micro corner

cube reflectors 10th IEEE Intl Workshop on Micro Electro
Mechanical Systems
2. J . Kahn , R.H.Katz, KSJ Pister Mobile Networking for Smart
Dust

3. www.eecs.berkerly.edu

4. www.seminarsonly.com

www.studymafia.org

ABSTRACT
Advances in hardware technology have enabled very compact,
autonomous and mobile nodes each having one or more sensors,
computation and communication capabilities, and a power supply. The
Smart Dust project is exploring whether an autonomous sensing,
computing, and communication system can be packed into a cubicmillimeter mote to form the basis of integrated, massively distributed sensor
networks. It focuses on reduction of power consumption, size and cost. To
build these small sensors, processors, communication devices, and power
supply , designers have used the MEMS (Micro electro mechanical
Systems) technology.
Smart Dust nodes otherwise known as motes are usually of the
size of a grain of sand and each mote consists of :
1. sensors
2. transmitter & receiver enabling bidirectional wireless communication.
3. processors and control circuitory
4. power supply unit

Using smart dust nodes,

the energy to acquire and process a

sample and then transmit some data about it could be as small as a few
nanoJoules.

These dust motes enable a lot of applications, because at these

small dimensions ,these motes can be scattered from aircraft for battle field

www.studymafia.org
monitoring or can be stirred into house paint to create the ultimate home
sensor network.

CONTENTS

WHAT IS A SMART DUST?

THE MEMS TECHNOLOGY IN SMART DUST

SMART DUST TECHNOLOGY

OPERATION OF THE MOTE

COMMUNICATING WITH A SMART DUST

OPTICAL COMMUNICATIONS

LISTENING TO A DUST FIELD

CORE FUNCTIONALITY SPECIFICATION PERFORMING A

TASK

MAJOR CHALLENGES

APPLICATIONS

HOW FAR THEY HAVE BEEN IMPLEMENTED

SUMMARY

REFERENCES