Scribd
Upload
174 views5 pages

DTMF Tone Generationca

This document describes a lab assignment to program a TI DSK board to generate DTMF tones. The objectives are to get familiar with the TI Code Composer Studio development environment and TI-DSP Starter Kit hardware. The lab has two parts: 1) program the on-board dip switches and LEDs such that each dip switch controls its corresponding numbered LED; 2) program the dip switches to generate DTMF tones for touch-tone dialing, where each combination of dip switch states corresponds to a button on a phone keypad. The document provides step-by-step instructions for setting up a Code Composer Studio project, writing C code to control the hardware, compiling and loading the program onto the DSK board.

Uploaded by

Rajesh S
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
174 views5 pages

DTMF Tone Generationca

This document describes a lab assignment to program a TI DSK board to generate DTMF tones. The objectives are to get familiar with the TI Code Composer Studio development environment and TI-DSP Starter Kit hardware. The lab has two parts: 1) program the on-board dip switches and LEDs such that each dip switch controls its corresponding numbered LED; 2) program the dip switches to generate DTMF tones for touch-tone dialing, where each combination of dip switch states corresponds to a button on a phone keypad. The document provides step-by-step instructions for setting up a Code Composer Studio project, writing C code to control the hardware, compiling and loading the program onto the DSK board.

Uploaded by

Rajesh S
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Dual Tone Multi-Frequency (DTMF) Generation with

TI-DSP TMS320C6713 Processor


Objective
The goals of this lab are to gain familiarity with TI DSP code composer studio and the TI-DSP
Starter Kit (DSK). These goals can be accomplish by:
Programming the 4 dip switches,
Controlling the leds with dip switches,
Output through onboard codec.
Walk-through
1. Power up the TI-DSP evaluation module.
2. Make sure the speaker is connected to the headphone jack.
3. Reset the board, by pressing the on-board reset button, there will be running LEDs and also
an available beep as an indication that the on-board sound CODEC is working fine.
4. Perform the 6713 DSK Diagnostic Utility to verify the functionality of the DSK.
5. Make sure all the DSK passed all the diagnostics.

Figure 1: 6713 DSK Diagnostic Utility.

Part 1
1. Create a folder called myprojects on the desktop.

The location of the myprojects


folder.

Figure 2: Code composer Studio.

2.
3.
4.
5.
6.

Run the C6713 DSK Code Composer Studio (C6713 DSK CCS).
Go to Project New, create a project called dtmf.
Make sure the Project Type is Executalble (.out) and Target is TMS329C67XX.
Download the dtmf.cdb file from http://www.ece.mtu.edu/labs/EElabs/EE3306/resources.
Once the project is created, go to Project Add files to project, add the DSK6713 Board
Support Library (BSL)file. This library will simplify the communication with the board using
C language. The file is located at C:\ti\c6000\dsk6713\lib\dsk6713bsl.lib. More information
about this library can be found in Help TMS320C6713 DSK Software Board
Support Library.
7. Next, include the dtmf.cdb file from the webpage. This configuration file will setup all the
DSP/BIOS correctly for the use of this lab.
8. Finally, you can create a new file and begin the laboratory assignment. Remember to save the
file as dtmf.c and include it to the project in order for it to run.

Figure 3: After including all necessary files.

Compiling into Machine Language


1. After writing the code, the next step is to compile the code to machine language. Go to
Project Build.
2. The Build command will compile all the files that are include in this project and make an
executable file for the DSP.
3. Compiler results are shown at the bottom of the window.

Rebuild All

Compiler windows

Figure 4: Compiler Comments.

4. Loading Program into DSP Processor


1. Finally, to run the program, load the program into the DSP. Go to File Load Program.
Load the executable file (.out) that the compiler generated (generally in the Debug directory
of the project).

Figure 5: Load Program.

2. The run the file loaded into the DSP. Go to Debug Run.

Run

Figure 6: Program running.

Laboratory Assignment
Task 1
First part of the laboratory is to program the each dip switch to control their respectively
numbered led (e.g. dip switch # 1 controls led #1, etc).
HAVE YOUR TA VERIFY YOUR WORK TO THIS POINT

(initials) ___________

Task 2
DTMF tones are used in telephone for tone dialing. Each key on a keypad has a distinct sound
made up of two single-frequency tones. One tone represents the column and the other tone
represents the row as shown in Figure 7. For example if you push the 2 key, you get two tones
one at 1336Hz because it is in column 2 and one at 697 Hz because it is in row 1. Therefore,
when a number is dial on a dial tone phone, the actual detection of the number dial is through
detection of what tones that are being dialed.

Figure 7: DTMF frequencies.

In task 2, you are required to generate the all the 12 buttons/keys on a conventional dial-tone
phone. You are going to program the dip switches to generate different DTMF tone. The dip
switches will act as binary bit which correspond to Table 1.
Binary
0000
0001
0010
0011
0100
0101

Symbol
0
1
2
3
4
5

Binary
0110
0111
1000
1001
1010
1011

Symbol
6
7
8
9
*
#

Table 1: Dip switch condition and symbol.

The dip switches and LEDs are labeled from 0 3. Therefore, your program will reflect that the
least significant bit correspond to dip switch # 3 and led # 3.
Hint : Basically, the DSP must (1) read the input from the dip switches, (2) determined which
switch is pressed, (3) generate the standard touch-tone frequencies for that switch combination
corresponding to Table 1 and finally, output the tones through the connected speaker.
HAVE YOUR TA VERIFY YOUR WORK TO THIS POINT

(initials) ___________

You might also like