MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

07/10/13

Material Safety Data Sheet

Copyright, 2013, 3M Company All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.

SECTION 1: PRODUCT AND COMPANY IDENTIFICATION

PRODUCT NAME: 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099
MANUFACTURER: 3M
DIVISION: Industrial Adhesives and Tapes Division
ADDRESS: 3M Center, St. Paul, MN 55144-1000

EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)

Issue Date: 07/10/13
Supercedes Date: 05/17/12
Document Group: 10-2442-1
Product Use:
Specific Use:
Intended Use:

plastic adhesive
Industrial use

SECTION 2: INGREDIENTS
Ingredient

C.A.S. No.

% by Wt

Acetone
Acrylonitrile-Butadiene Polymer
Phenolic Polymer
Phenolic Resin
Salicylic Acid
Zinc Oxide
Antioxidant
Phenol

67-64-1
9003-18-3
55185-45-0
25085-50-1
69-72-7
1314-13-2
68411-46-1
108-95-2

60 - 70
10 - 20
5 - 10
5 - 10
1- 5
1- 3
< 0.4
< 0.4

SECTION 3: HAZARDS IDENTIFICATION

3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: White/pink to light tan liquid - ketone odor
General Physical Form: Liquid
Immediate health, physical, and environmental hazards: Closed containers exposed to heat from fire may build pressure and
explode. Extremely flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and
_________________________________________________________________________________________________
Page 1 of 8

MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

flash back.
May cause severe eye irritation.
cause birth defects or other reproductive harm.

07/10/13

May cause target organ effects. Contains a chemical or chemicals which can

3.2 POTENTIAL HEALTH EFFECTS

Eye Contact:
Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing, cloudy appearance of the cornea, and
impaired vision.
Skin Contact:
Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, and itching.
Inhalation:
Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and
throat pain.
May be absorbed following inhalation and cause target organ effects.
Ingestion:
Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea.
May be absorbed following ingestion and cause target organ effects.
Target Organ Effects:
Central Nervous System (CNS) Depression: Signs/symptoms may include headache, dizziness, drowsiness, incoordination, nausea,
slowed reaction time, slurred speech, giddiness, and unconsciousness.
Contains a chemical or chemicals which can cause birth defects or other reproductive harm.

SECTION 4: FIRST AID MEASURES

4.1 FIRST AID PROCEDURES
The following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Immediately flush eyes with large amounts of water for at least 15 minutes. Get immediate medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: Remove person to fresh air. If signs/symptoms develop, get medical attention.
If Swallowed:
Do not induce vomiting unless instructed to do so by medical personnel. Give victim two glasses of water. Never
give anything by mouth to an unconscious person. Get medical attention.

SECTION 5: FIRE FIGHTING MEASURES

5.1 FLAMMABLE PROPERTIES
Autoignition temperature
Flash Point
Flammable Limits(LEL)
Flammable Limits(UEL)
OSHA Flammability Classification:

465 C [Details: Acetone]

-4 F [Test Method: Closed Cup]
2.6 % volume
12.8 % volume
Class IB Flammable Liquid

_________________________________________________________________________________________________
Page 2 of 8

MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

07/10/13

5.2 EXTINGUISHING MEDIA

Use fire extinguishers with class B extinguishing agents (e.g., dry chemical, carbon dioxide).

5.3 PROTECTION OF FIRE FIGHTERS

Special Fire Fighting Procedures: Water may not effectively extinguish fire; however, it should be used to keep fire-exposed
containers and surfaces cool and prevent explosive rupture. Wear full protective equipment (Bunker Gear) and a self-contained
breathing apparatus (SCBA).
Unusual Fire and Explosion Hazards: Closed containers exposed to heat from fire may build pressure and explode. Extremely
flammable liquid and vapor. Vapors may travel long distances along the ground or floor to an ignition source and flash back.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.

SECTION 6: ACCIDENTAL RELEASE MEASURES

6.1. Personal precautions, protective equipment and emergency procedures
Evacuate unprotected and untrained personnel from hazard area. The spill should be cleaned up by qualified personnel. Remove all
ignition sources such as flames, smoking materials, and electrical spark sources. Use only non-sparking tools. Ventilate the area with
fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with
good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill
area to burn or explode. Remember, adding an absorbent material does not remove a toxic, corrosivity or flammability hazard.
6.2. Environmental precautions
For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. Collect the resulting residue
containing solution. Place in a metal container approved for transportation by appropriate authorities. Dispose of collected material
as soon as possible.
Clean-up methods
Refer to other sections of this MSDS for information regarding physical and health hazards, respiratory protection, ventilation, and
personal protective equipment. Call 3M-HELPS line (1-800-364-3577) for more information on handling and managing the spill.
Contain spill. Cover spill area with a fire-extinguishing foam. An aqueous film forming foam (AFFF) is recommended. Working
from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material.
Mix in sufficient absorbent until it appears dry. Collect as much of the spilled material as possible using non-sparking tools. Clean up
residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow
safety precautions on the solvent label and MSDS. Seal the container.
In the event of a release of this material, the user should determine if the release qualifies as reportable according to
local, state, and federal regulations.

SECTION 7: HANDLING AND STORAGE

7.1 HANDLING
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water. Contents may be under
pressure, open carefully. Ground containers securely when transferring contents. Wear low static or properly grounded shoes. Avoid
breathing of vapors, mists or spray. Avoid static discharge. Avoid eye contact with vapors, mists, or spray. Keep out of the reach of
children. Vapors may ignite explosively. May cause flash fire. Prevent build-up of vapors - open all windows and doors. Maintain
vapor concentrations below recommended exposure limits. Use only with cross-ventilation. Without adequate ventilation, vapors may
settle in low-lying areas. Keep away from heat, sparks, and open flame. Do not smoke or ignite matches, lighters, etc. Do not breathe
vapors. Avoid contact with oxidizing agents.

_________________________________________________________________________________________________
Page 3 of 8

MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

07/10/13

7.2 STORAGE
Store away from acids. Store away from heat. Store out of direct sunlight. Keep container in well-ventilated area. Keep container
tightly closed. Store away from areas where product may come into contact with food or pharmaceuticals. Store away from oxidizing
agents.

SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION

8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide appropriate local exhaust ventilation on open containers. Use in an enclosed
process area is recommended. If exhaust ventilation is not available, use appropriate respiratory protection.

8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)

8.2.1 Eye/Face Protection
Avoid eye contact with vapors, mists, or spray.
The following eye protection(s) are recommended: Safety Glasses with side shields
Indirect Vented Goggles
.
8.2.2 Skin Protection
Not applicable. Avoid skin contact.
Select and use gloves and/or protective clothing to prevent skin contact based on the results of an exposure assessment. Consult with
your glove and/or protective clothing manufacturer for selection of appropriate compatible materials.
Gloves made from the following material(s) are recommended: Butyl Rubber
Polymer laminate
.
8.2.3 Respiratory Protection
Avoid breathing of vapors, mists or spray. Do not breathe vapors.
An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full
respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce
inhalation exposure:
Half facepiece or full facepiece air-purifying respirator suitable for organic vapors
For questions about suitability for a specific application, consult with your respirator manufacturer.
8.2.4 Prevention of Swallowing
Do not eat, drink or smoke when using this product. Wash exposed areas thoroughly with soap and water.

8.3 EXPOSURE GUIDELINES

Ingredient

Authority

Acetone
Acetone
Acetone
Phenol
Phenol
Zinc Oxide

ACGIH
ACGIH
OSHA
ACGIH
OSHA
ACGIH

Zinc Oxide

ACGIH

Zinc Oxide
Zinc Oxide

OSHA
OSHA

Type
TWA
STEL
TWA
TWA
TWA
TWA, respirable
fraction
STEL, respirable
fraction
TWA, as fume
TWA, respirable
fraction

Limit
500 ppm
750 ppm
2400 mg/m3
5 ppm
19 mg/m3
2 mg/m3

Additional Information

Skin Notation*
Skin Notation*

10 mg/m3
5 mg/m3
5 mg/m3

_________________________________________________________________________________________________
Page 4 of 8

MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

Zinc Oxide

OSHA

TWA, as total dust

07/10/13

15 mg/m3

* Substance(s) refer to the potential contribution to the overall exposure by the cutaneous route including mucous membrane and eye,
either by airborne or, more particularly, by direct contact with the substance. Vehicles can alter skin absorption.
SOURCE OF EXPOSURE LIMIT DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES

Odor, Color, Grade:
General Physical Form:
Autoignition temperature
Flash Point
Flammable Limits(LEL)
Flammable Limits(UEL)
Boiling Point
Density
Vapor Density

White/pink to light tan liquid - ketone odor

Liquid
465 C [Details: Acetone]
-4 F [Test Method: Closed Cup]
2.6 % volume
12.8 % volume
>=56 C
0.89 g/ml
2.0 [Ref Std: AIR=1]

Vapor Pressure

<=185 mmHg [@ 68 F]

Specific Gravity
pH
Melting point

0.89 [Ref Std: WATER=1]

Not Applicable
Not Applicable

Solubility in Water
Evaporation rate
Hazardous Air Pollutants
Volatile Organic Compounds
Kow - Oct/Water partition coef
Percent volatile
VOC Less H2O & Exempt Solvents
VOC Less H2O & Exempt Solvents
VOC Less H2O & Exempt Solvents
Viscosity
Solids Content

Slight (less than 10%)

1.9 [Ref Std: ETHER=1]
<=0.5 % weight [Test Method: Calculated]
568 g/l [Details: EU VOC content]
No Data Available
60 - 70 % weight
4 g/l [Test Method: calculated SCAQMD rule 443.1]
0.04 lb/gal [Test Method: calculated SCAQMD rule 443.1]
0.5 % [Test Method: tested per SCAQMD method 305]
2150 centipoise [@ 73.4 F]
>=36.1 %

SECTION 10: STABILITY AND REACTIVITY

Stability: Stable.
Materials and Conditions to Avoid:
10.1 Conditions to avoid
Heat
Sparks and/or flames
10.2 Materials to avoid
Strong oxidizing agents

_________________________________________________________________________________________________
Page 5 of 8

MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

07/10/13

Hazardous Polymerization: Hazardous polymerization will not occur.

Hazardous Decomposition or By-Products

Substance

Condition

Aldehydes
Hydrocarbons
Carbon monoxide
Carbon dioxide
Hydrogen Cyanide
Ketones
Oxides of Nitrogen
Oxides of Zinc

During Combustion
During Combustion
During Combustion
During Combustion
During Combustion
During Combustion
During Combustion
During Combustion

SECTION 11: TOXICOLOGICAL INFORMATION

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.

SECTION 12: ECOLOGICAL INFORMATION

ECOTOXICOLOGICAL INFORMATION
Not determined.

CHEMICAL FATE INFORMATION

Not determined.

SECTION 13: DISPOSAL CONSIDERATIONS

Waste Disposal Method: Reclaim solvent if feasible. Incinerate in a permitted hazardous waste incinerator. As a disposal
alternative, dispose of waste product in a permitted hazardous waste facility.
EPA Hazardous Waste Number (RCRA): D001 (Ignitable)
Since regulations vary, consult applicable regulations or authorities before disposal.

SECTION 14:TRANSPORT INFORMATION

ID Number
62-1099-2631-1
62-1099-6530-1
62-1099-8530-9
62-1099-9532-4

UPC
00-21200-19808-3
00-21200-19811-3
00-21200-19814-4
00-48011-58552-9

ID Number
62-1099-2635-2
62-1099-7530-0
62-1099-9530-8
62-1099-9535-7

UPC
00-21200-19813-7
00-21200-19815-1
00-21200-30007-3

For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501.

_________________________________________________________________________________________________
Page 6 of 8

MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

07/10/13

SECTION 15: REGULATORY INFORMATION

US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard - Yes Pressure Hazard - No

Reactivity Hazard - No

Immediate Hazard - Yes

Delayed Hazard - Yes

Section 313 Toxic Chemicals subject to the reporting requirements of that section and 40 CFR part 372 (EPCRA):
Ingredient

C.A.S. No

Zinc Oxide (ZINC COMPOUNDS)

1314-13-2

% by Wt
1- 3

STATE REGULATIONS
Contact 3M for more information.

CHEMICAL INVENTORIES
The components of this product are in compliance with the chemical notification requirements of TSCA.
All applicable chemical ingredients in this material are listed on the European Inventory of Existing Chemical Substances (EINECS),
or are exempt polymers whose monomers are listed on EINECS.
Contact 3M for more information.

INTERNATIONAL REGULATIONS
Contact 3M for more information.
This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.

SECTION 16: OTHER INFORMATION

NFPA Hazard Classification
Health: 2

Flammability: 3

Reactivity: 0

Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.

Revision Changes:
Section 7: Handling information was modified.
Section 7: Storage information was modified.
Section 8: Engineering controls information was modified.
Section 8: Skin protection phrase was modified.
Section 8: Respiratory protection information was modified.
Section 8: Prevention of swallowing information was modified.
Section 8: Respiratory protection - recommended respirators was modified.
Section 8: Respiratory protection - recommended respirators guide was modified.
Section 2: Ingredient table was modified.
Copyright was modified.
Section 8: Respiratory protection - recommended respirators punctuation was deleted.
DISCLAIMER: The information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY
_________________________________________________________________________________________________
Page 7 of 8

MATERIAL SAFETY DATA SHEET 3M Scotch-Weld Nitrile High Performance Plastic Adhesive 1099

07/10/13

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF

TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user's method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M

3M USA MSDSs are available at www.3M.com

_________________________________________________________________________________________________
Page 8 of 8