Exergy A Measure of Work Potential

Ch 8 EXERGY: A MEASURE OF WORK POTENTIAL
Objectives
The objectives of Chapter 8 are to:
Examine the performance of engineering devices in light of the second law of thermodynamics.
Define exergy, which is the maximum useful work that could be obtained from the
system at a given state in a specified environment.
Define reversible work, which is the maximum useful work that can be obtained as a system
undergoes a process between two specified states.
Define the exergy destruction, which is the wasted work potential during a process as a result of
irreversibilities.
Define the second-law efficiency.
Develop the exergy balance relation.
Apply exergy balance to closed systems and control volumes.
81 Exergy: Work Potential of Energy
Exergy of kinetic energy:
xke = ke = V2 /2 (kJ/kg)
(81)
Where V is the velocity in m/s of the system relative to the environment.

Exergy of potential energy:
xpe = pe = gz (kJ/kg)
where g is the gravitational acceleration and z is the elevation of the system
relative to a reference level in the environment.
Example 81 Maximum Power Generation by a Wind Turbine

A wind turbine with a 12-m-diameter rotor, as shown in Fig. 86, is to be installed at a location
where the wind is blowing steadily at an average velocity of 10 m/s. Determine the maximum power
that can be generated by the wind turbine.
Thermodynamics II Sciences/ Ch8
1 of 13
Dr. Nasser T. Ahmad
Solution:
Exergy = Maximum power =m * (ke) = (1335 kg/s)(0.05 kJ/kg) = 66.8 kW
82 REVERSIBLE WORK AND IRREVERSIBILITY
Example 83 The Rate of Irreversibility of a Heat Engine

A heat engine receives heat from a source at 1200 K at a rate of 500 kJ/s and rejects the waste heat
to a medium at 300 K. The power output of the heat engine is 180 kW.
Determine the reversible power and the irreversibility rate for this process.
Solution:
th,rev=1-300/1200=75 %
Actual efficiency= 180/500= 0.36 = 36 %
Quiz on Sunday 13-10-2014 on Ch 8

83 SECOND-LAW EFFICIENCY, II
84 Exergy Change of a System

: The expression is called flow (or stream) exergy
2 of 13
Dr. Nasser T. Ahmad
Example 88 Exergy Change during a Compression Process

Refrigerant-134a is to be compressed from 0.14 MPa and 10C to 0.8 MPa and 50C steadily by a compressor. Taking
the environment conditions to be T0= 20C and 95 kPa,
determine the exergy change of the refrigerant during this
process and the minimum work input that needs to be supplied
to the compressor per unit mass of the refrigerant.
The properties of the refrigerant at the inlet and the exit states are
85 EXERGY TRANSFER BY HEAT, WORK, AND MASS

Exergy by Heat Transfer, Q
FIGURE 826 The Carnot efficiency c = 1 - T0 /T represents the fraction of the energy transferred from a heat source
at temperature T that can be converted to work in an environment at temperature T0.
3 of 13
Dr. Nasser T. Ahmad
This relation gives the exergy transfer accompanying heat transfer Q whether T is greater than or less than T0. When T
>T0, heat transfer to a system increases the exergy of that system and heat transfer from a system decreases it. But the
opposite is true when T < T0. In this case, the heat transfer Q is the heat rejected to the cold medium (the waste heat), and
it should not be confused with the heat supplied by the environment at T0. The exergy transferred with heat is zero when
T = T0 at the point of transfer.
FIGURE 827 The transfer and destruction of exergy during a heat transfer process through a finite temperature
difference.
4 of 13
Dr. Nasser T. Ahmad
Exergy Transfer by Work, W
Exergy Transfer by Mass, m

Therefore, the exergy of a system increases by mc when mass in the amount of m enters, and decreases by the same
amount when the same amount of mass at the same state leaves the system (Fig. 829).
Exergy flow associated with a fluid stream when the fluid properties are variable can be determined by integration from
where Ac is the cross-sectional area of the flow and Vn is the local velocity normal to dAc.
Note that exergy transfer by heat Xheat is zero for adiabatic systems, and the exergy transfer by mass Xmass is zero for
systems that involve no mass flow across their boundaries (i.e., closed systems).
The total exergy transfer is zero for isolated systems since they involve no heat, work, or mass transfer.
FIGURE 829 Mass contains energy, entropy, and exergy, and thus mass flow into or out of a system is accompanied
by energy, entropy, and exergy transfer.
86 THE DECREASE OF EXERGY PRINCIPLE AND EXERGY DESTRUCTION

Exergy Destruction
Irreversibilities such as friction, mixing, chemical reactions, heat transfer through a

finite temperature difference, unrestrained expansion, nonquasiequilibrium
compression or expansion always generate entropy, and anything that generates
entropy always destroys exergy.
The exergy destroyed is proportional to the entropy generated, as can be seen from
Eq. 831, and is expressed as
5 of 13
Dr. Nasser T. Ahmad
FIGURE 831 The exergy
change of a system can be negative, but the exergy destruction cannot.
Tuesday 30-09-2014
87 EXERGY BALANCE: CLOSED SYSTEMS
FIGURE 832
Mechanisms of exergy transfer.
EXAMPLE 811 Exergy Destruction during Expansion of Steam

A pistoncylinder device contains 0.05 kg of steam at 1 MPa and 300C. Steam now
expands to a final state of 200 kPa and 150C, doing work. Heat losses from the system
to the surroundings are estimated to be 2 kJ during this process.
Assuming the surroundings to be at T0 = 25C and P0 =100 kPa, determine
(a) the exergy of the steam at the initial and the final states,
(b) the exergy change of the steam,
(c) the exergy destroyed, and
(d) the second-law efficiency for the process.
6 of 13
Dr. Nasser T. Ahmad
7 of 13
Dr. Nasser T. Ahmad
8 of 13
Dr. Nasser T. Ahmad
9 of 13
Dr. Nasser T. Ahmad
88 EXERGY BALANCE: CONTROL VOLUMES
FIGURE 842 Exergy
is transferred into or out of a control volume by mass as well as heat and work
transfer.
EXAMPLE 815 Second-Law Analysis of a Steam Turbine

Steam enters a turbine steadily at 3 MPa and 450C at a rate of 8 kg/s and exits at 0.2 MPa
and 150C, (Fig. 845). The steam is losing heat to the surrounding air at 100 kPa and
25C at a rate of 300 kW, and the kinetic and potential energy changes are negligible.
Determine (a) the actual power output, (b) the maximum possible power output, (c) the
second-law efficiency, (d) the exergy destroyed, and (e) the exergy of the steam at the
inlet conditions.
10 of 13
Dr. Nasser T. Ahmad
11 of 13
Dr. Nasser T. Ahmad
12 of 13
Dr. Nasser T. Ahmad
Quiz on Ch 8 on Sunday 12-10-2014
Recommended Problems
836 An insulated pistoncylinder device contains 2 L of
saturated liquid water at a constant pressure of 150 kPa. An
electric resistance heater inside the cylinder is turned on, and
electrical work is done on the water in the amount of 2200 kJ.
13 of 13
Dr. Nasser T. Ahmad
Assuming the surroundings to be at 25C and 100 kPa, determine

(a) the minimum work with which this process could be
accomplished and (b) the exergy destroyed during this
process. Answers: (a) 437.7 kJ, (b) 1705 kJ
14 of 13
Dr. Nasser T. Ahmad
15 of 13
Dr. Nasser T. Ahmad
16 of 13
Dr. Nasser T. Ahmad
17 of 13
Dr. Nasser T. Ahmad
18 of 13
Dr. Nasser T. Ahmad

Exergy A Measure of Work Potential

Uploaded by

Copyright:

Available Formats

Exergy A Measure of Work Potential

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Exergy A Measure of Work Potential

Uploaded by

Copyright:

Available Formats

Ch 8 EXERGY: A MEASURE OF WORK POTENTIAL

81 Exergy: Work Potential of Energy

Exergy of kinetic energy:

Where V is the velocity in m/s of the system relative to the environment.

Example 81 Maximum Power Generation by a Wind Turbine

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Exergy = Maximum power =m * (ke) = (1335 kg/s)(0.05 kJ/kg) = 66.8 kW

82 REVERSIBLE WORK AND IRREVERSIBILITY

Example 83 The Rate of Irreversibility of a Heat Engine

Quiz on Sunday 13-10-2014 on Ch 8

84 Exergy Change of a System

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Example 88 Exergy Change during a Compression Process

85 EXERGY TRANSFER BY HEAT, WORK, AND MASS

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Exergy Transfer by Work, W

Exergy Transfer by Mass, m

86 THE DECREASE OF EXERGY PRINCIPLE AND EXERGY DESTRUCTION

Irreversibilities such as friction, mixing, chemical reactions, heat transfer through a

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

FIGURE 831 The exergy

change of a system can be negative, but the exergy destruction cannot.

87 EXERGY BALANCE: CLOSED SYSTEMS

Mechanisms of exergy transfer.

EXAMPLE 811 Exergy Destruction during Expansion of Steam

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

88 EXERGY BALANCE: CONTROL VOLUMES

FIGURE 842 Exergy

EXAMPLE 815 Second-Law Analysis of a Steam Turbine

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Quiz on Ch 8 on Sunday 12-10-2014

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Assuming the surroundings to be at 25C and 100 kPa, determine

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad

Thermodynamics II Sciences/ Ch8

Dr. Nasser T. Ahmad