Lab Manual EC0323 Communication Lab-II Lab

EC0323 COMMUNICATION LAB II
LABORATORY MANUAL
SEMESTER V
DEAPRTMENT OF
ELECTRONICS AND COMMUNICATION ENGINEERING
SRM UNIVERISTY
(Under SECTION 3 of the UGC Act, 1956)
S.R.M. NAGAR, KATTANKULATHUR 603203.

KANCHEEPURAM DISTRICT
Department of Electronics and Communication Engineering
EC0323
Communication Lab II
Laboratory Manual
Course Team
Mr.K.Kalimuthu
Mrs.P.Malarvezhi
Mrs.G.Kalaimagal
Mr.A.Sriram
Mrs.T.Theresal
Mrs.Sabitha Gaubi
Mrs.BKolangiammal
Mrs.S.Muthukumaran
Mrs.P.Ponammal
June 2014
Revision: 4
S.R.M University
Faculty of Engineering and Technology
Sub Code : EC0323
Sub Title : Communication lab II
Pre_requisite
Co_requisite
Semester
:V
Course Time : JulDec 2011
: Nil
: EC0307 Digital Communication
Program Outcome
b. Graduate will demonstrate the ability to identify, formulate and solve engineering
problem
Experiment 7: To identify the various encoding schemes for a given data stream
c. Graduate will demonstrate the ability to design and conduct experiments, analyze
and interpret data
Experiment 2 : To analyze a PCM system and interpret
waveforms for a sampling frequency of 4KHz.
the modulated and demodulated
Experiment 3 : To analyze a DPCM system and interpret the modulated and demodulated
waveforms for a sampling frequency of 8KHz.
Experiment 4 : To analyze a Delta modulation system and interpret
demodulated waveforms.
the modulated and
Experiment 5: To analyze a FSK modulation system and interpret

the modulated and
Experiment 6: To analyze a PSK modulation system and interpret

the modulated and
d. Graduate will demonstrate the ability to design a system, component or process as

per needs and specification
Experiment 1:To demonstrate Time Division Multiplexing and demultiplexing process using
Pulse amplitude modulation signals
f. Graduate will demonstrate the skills to use modern engineering tools, softwares
and equipment to analyze problems
Experiment 8: To simulate Binary Amplitude shift keying technique using MATLAB software
Experiment 9: To simulate Binary Frequency shift keying technique using MATLAB software
Experiment 10: To simulate Binary Phase shift keying technique using MATLAB software
Experiment 11: To simulate Quadrature Phase shift keying technique using MATLAB software
Experiment 11: To simulate Differential Phase shift keying technique using MATLAB software
Sub Code : EC0323

Sub Title : Communication Lab II
Semester
:V
Course Time : Jul- Dec 2011
Pre Requisite
Course Requisite : EC0307 Digital Communication
Instructional Objective and Program Outcome

S.No. Instructional
Program Outcome
Experiment Details
c. Graduate will demonstrate the

ability to design and conduct
experiments, analyze and interpret
data
Experiment 2 : To analyze a PCM system. and

interpret the modulated and demodulated
waveforms for a sampling frequency of 4KHz
Objective
1
To carry out experiments on

various digital
communications
modulation schemes using
kits.
Experiment 3 : To analyze a DPCM system.

and interpret the modulated and demodulated
waveforms for a sampling frequency of 8KHz
Experiment 4 : To analyze a Delta modulation
system. and interpret the modulated and
Experiment 5: To analyze a FSK modulation
Experiment 6: To analyze a PSK modulation
To simulate the digital

modulation techniques using
b. Graduate will demonstrate the

ability to identify, formulate and
solve engineering problem
Experiment 7: To identify the various

encoding schemes for a given data stream.
d. Graduate will demonstrate the

ability to design a system,
component or process as per needs
and specification
Experiment 1:To demonstrate Time Division

Multiplexing and demultiplexing process
using Pulse amplitude modulation signals.
f. Graduate will demonstrate the
Experiment 8: To simulate Binary Amplitude
MATLAB software.
skills to use modern engineering

tools, softwares and equipment to
analyze problems.
shift keying technique using MATLAB

software
Experiment 9: To simulate Binary Frequency
software
Experiment 10: To simulate Binary Phase
software
Experiment 11: To simulate Quadrature Phase
software
Experiment 12: To simulate Differential
Phase shift keying technique using MATLAB
software
S.R.M University
Sub Code : EC0323
Sub Title : Communication Lab II
Semester
:V
Course Time : JulDec 2011
Pre Requisite
:
Course Requisite : EC0307 Digital Communication
EXPERIMENTS DETAILS
S.No.
Experiments Detail
Equipments Required
Specifications
To demonstrate Time Division

Multiplexing and demultiplexing
process using Pulse amplitude
modulation signals.
TDM Trainer kit

CRO(30 MHz)
Crystal Frequency 6.4MHz

Analog Input channel:4
Onboard analog
signal:250Hz,500Hz,1KHz,2KHz
Sampling Rate:16Khz/Channel
Clock Regeneration at receiver: Using
PLL
Low pass filter cut off frequency:3.4Khz
To analyze a PCM system. and PCM Trainer Kit

interpret
the modulated and CRO(30 MHz)
demodulated waveforms for a
sampling frequency of 4KHz .
Regulated power supply IC 7805 ,IC7812

: +5V and +12 V at 300 mA.
AF Signal generator IC TL084: 200Hz,
Sinewave
Clock Generator IC555:64KHz and 4KHz
DC Source : +5V
LPF: Cut off frequency 200Hz
Amplifier ICTL084: Gain 0 to 3.
Sample and hold: LF198/LF298/LF398:
A/D Converter IC ADC0808 : 8 bit
P/S shift register SN74LS166 : 8 bit
S/P shift register SN74LS164 : 8 bit
DAC ICDAC 0808: 8 bit
To analyze a DPCM system and DPCM Trainer Kit

interpret
the modulated and CRO(30 MHz)
demodulated waveforms for a
sampling frequency of 8 KHz.
ADCL-07 Kit
.

: +5V and +12 V at 300 mA.
AF Signal generator IC TL084:400Hz,
Sinewave
Clock Generator IC 555 : 64KHz and
8KHz
DC Source :0 to 290mV
LPF: Cut off frequency 400Hz
Sample and hold: LF198/LF298/LF398:
A/D Converter IC ADC0808 : 8 bit
P/S shift register SN74LS166 : 8 bit
S/P shift register SN74LS164 : 8 bit
To analyze a Delta modulation Delta modulation Trainer Kit

system and interpret the modulated CRO(30 MHz)
and demodulated waveforms.

: +5V and +12 V at 300 mA.
AF Signal generator IC TL084: 100Hz,
Sinewave
Clock Generator IC 555 : 4 Khz
DC Source : 0 to +5V
LPF: Cut off frequency 100hz
Buffer/Signal shaping circuit:IC TL084
Voltage comparator: IC LM339
UPdown Counter:IC74LS191, 4 bit.
To analyze a FSK modulation FSK Trainer Kit

VCO: IC XR2206
Comparator:LM565
To analyze a PSK modulation PSK Trainer Kit

4 channel analog Multiplexer: IC CD

4052
opampTL084
To identify the various encoding Data formatting Trainer Kit

schemes for a given data stream.
CRO(30 MHz)
On-board carrier: Sine waves

synchronized to transmitted data at
1.44MHz,960 KHz(0 deg. Phase),960
KHz(90 deg. Phase)
To simulate Binary Amplitude shift MATLAB software

keying technique using MATLAB
software
version7.2
To simulate Binary Frequency shift MATLAB software

software
version7.2
10
To simulate Binary Phase shift MATLAB software

software
version7.2
11
To simulate Quadrature Phase shift MATLAB software

software
version7.2
12
To simulate Differential Phase shift MATLAB software

software
version7.2
EC0323 Laboratory Policies and Report Format

Reports are due at the beginning of the lab period. The reports are intended to be a
complete documentation of the work done in preparation for and during the lab.
The report should be complete so that someone else familiar with digital
communication could use it to verify your work. The prelab and postlab report
format is as follows:
1. A neat thorough prelab must be presented to your Staff Incharge at the
beginning of your scheduled lab period. Lab reports should be submitted on A4
paper. Your report is a professional presentation of your work in the lab.
Neatness, organization, and completeness will be rewarded. Points will be
deducted for any part that is not clear.
2. In this laboratory students will work in teams of three. However, the lab reports
will be written individually. Please use the following format for your lab reports.
a. Cover Page: Include your name, Subject Code, Section No., Experiment
No. and Date.
b.Objectives: Enumerate 3 or 4 of the topics that you think the lab will
teach you. DO NOT REPEAT the wording in the lab manual procedures. There
should be one or two sentences per objective. Remember, you should write about
what you will learn, not what you will do.
c. Questions: Specific questions(Prelab and Postlab) asked in the lab
should be answered here.
3. Your work must be original and prepared independently. However, if you need
any guidance or have any questions or problems, please do not hesitate to approach
your staff incharge during office hours. Copying any prelab/postlab will result in a
grade of 0. The incident will be formally reported to the University and the
students should follow the dress code in the Lab session.
4. Each laboratory exercise (circuit) must be completed and demonstrated to your
Staff Incharge in order to receive working circuit credit. This is the procedure to
follow:
a. Circuit works: If the circuit works during the lab period (3 hours), call
your staff incharge, and he/she will sign and date it.. This is the end of this lab, and
you will get a complete grade for this portion of the lab.
b. Circuit does not work: If the circuit does not work, you must make use of
the open times for the lab room to complete your circuit. When your circuit is
ready, contact your staff incharge to set up a time when the two of you can meet to
check your circuit.
5. Attendance at your regularly scheduled lab period is required. An unexpected
absence will result in loss of credit for your lab. If for valid reason a student misses
a lab, or makes a reasonable request in advance of the class meeting, it is
permissible for the student to do the lab in a different section later in the week if
approved by the staff incharge of both the sections. Habitually late students (i.e.,
students late more than 15 minutes more than once) will receive 10 point
reductions in their grades for each occurrence following the first.
6. Final grade in this course will be based on laboratory assignments. All labs have
an equal weight in the final grade. Grading will be based on pre-lab work,
laboratory reports, post-lab and in-lab performance (i.e., completing lab, answering
laboratory related questions, etc.,).The Staff Incharge will ask pertinent questions
to individual members of a team at random. Labs will be graded as per the
following grading policy:
Pre-Lab Work
10.00%
In-Lab Performance
20.00%
Post Lab Work
10.00%
7. Reports Due Dates: Reports are due one week after completion of the
corresponding lab. A late lab report will have 10% of the points deducted for being
one day late. If a report is 2 days late, a grade of 0 will be assigned.
8. Systems of Tests: Regular laboratory class work over the full semester will
carry a weightage of 75%. The remaining 25% weightage will be given by
conducting an end semester practical examination for every individual student
Laboratory Report Cover Sheet

SRM University
EC0323 Communication Lab II Laboratory
Fifth Semester, 2014-15 (odd semester)
Name
Register No.
Day / Session
: Day order 1 AN / Day Order 4 FN
Venue
Title of Experiment
: communication Lab/Computing Lab 10th floor

:
Date of Conduction
Date of Submission
Particulars
Pre-lab
Max.
Marks
10
Lab Performance
20
Post-lab
10
Lab Report
10
Total
50
Marks
Obtained
REPORT VERIFICATION
Date
Staff Name
: Mrs.T.Theresal/ Anantha Venkatesan
Signature
CONTENTS
Exp 1: Time division multiplexing
Exp 2: Pulse code modulation
Exp 3: Differential Pulse code modulation
10
1.1 Objective
1.2 Hardware required
1.3 Introduction
1.4 Block diagram
1.5 Pre lab
1.6 Test procedure
1.7 Model graph
1.8 Observation
1.9 Lab result
1.10 Post lab
2.1 Objective
2.3 Introduction
2.3.1 PCM Modulator
2.3.2. PCM demodulator
2.4 Block diagram
2.5 Pre lab
2.6 Test procedure
2.6.1.PCM operation(DC Input)
2.6.2.PCM operation(AC Input)
2.7 Model graph
2.8 Observation
2.9 Lab result
2.10 Post lab
3.1 Objective
3.3 Introduction
3.3.1 DPCM Modulator
3.3.2.DPCM demodulator
3.4 Block diagram
3.5 Pre lab
3.6 Test procedure
3.7 Model graph
3.8 Observation
3.9 Lab result
3.10 Post lab
Exp 4: Delta modulation and demodulation
15
Exp 5: Frequency shift keying

5.1 Objective
5.3 Introduction
5.3.1 FSK Modulator
5.3.2FSK demodulator
5.4 Circuit diagram
5.5 Pre lab
5.6 Test procedure
5.7 Observation
5.8 Model graph
5.9 Lab result
5.10 Post lab
19
4.1 Objective
4.3 Introduction
4.4 Block diagram
4.5 Pre lab
4.6 Test procedure
4.7 Model graph
4.8 Observation
4.9 Lab result
4.10 Post lab
Exp 6: Phase shift keying
23
6.1 Objective
6.3 Introduction
6.3.1. PSK Modulator
6.3.2. PSK demodulator
6.4 Circuit diagram
6.5 Pre lab
6.6 Test procedure
6.6.1 Modulation
6.6.2 Demodulation
6.7 Model graph
6.8 observation
6.9 Lab result
6.10 Post lab
Exp 7: Data formatting

7.1 Objective
7.3 Introduction
7.4 Model graph
7.5 Pre lab
29
7.6 Test procedure

7.7 Lab result
7.8 Post lab
Exp 8: Binary Amplitude shift keying

8.1 Objective
8.2 Software required
8.3 Prelab
8.4 MATLAB Introduction
8.5 Theory
8.6 Algorithm
8.7 Test Procedure
8.8 Lab result
8.9 Post lab
Exp 9: Binary Frequency shift keying

9.1 Objective
9.3 Prelab
9.4 Theory
9.5 Algorithm
9.6 Test Procedure
9.7 Lab result
9.8 Post lab
Exp 10: Binary Phase shift keying

10.1 Objective
10.3 Prelab
10.4 Theory
10.5 Algorithm
10.6 Test Procedure
10.7 Lab result
10.8 Post lab
Exp 11: Quadrature Phase shift keying

11.1 Objective
11.3 Prelab
11.4 Theory
11.5 Algorithm
11.6 Test Procedure
11.7 Lab result
11.8 Post lab
Exp 12: Differential Phase shift keying
12.1 Objective
12.3 Prelab
32
35
12.4 Theory
12.5 Algorithm
12.6 Test Procedure
12.7 Lab result
12.8 Post lab
Appendix
1. TIME-DIVISION MULTIPLEX1NG
1.1.OBJECTIVE
To demonstrate Time Division Multiplexing and demultiplexing process using Pulse
amplitude modulation signals.
1.2. HARDWARE REQUIRED
1. TDM Trainer KitST2102
2. CRO
3. Patch Chords
4. Probes
1.3. INTRODUCTION
An important feature of pulse-amplitude modulation is a conservation of time. That is, for
a given message signal, transmission of the associated PAM wave engages the
communication channel for only a fraction of the sampling interval on a periodic basis.
Hence, some of the time interval between adjacent pulses of the PAM wave is cleared for
use by the other independent message signals on a time-shared basis. By so doing, we
obtain a time-division multiplex system (TDM), which enables the joint utilization of a
common channel by a plurality of independent message signals without mutual
interference.
Each input message signal is first restricted in bandwidth by a low-pass pre-alias filter to
remove the frequencies that are nonessential to an adequate signal representation. The
pre-alias filter outputs are then applied to a commutator, which is usually implemented
using electronic switching circuitry. The function of the commutator is two-fold: (1) to
take a narrow sample of each of the N input messages at a rate fs that is slightly higher
than 2W, where W is the cutoff frequency of the pre-alias filter, and (2) to sequentially
interleave these N samples inside a sampling interval Ts 1/fs. Indeed, this latter function
is the essence of the time-division multiplexing operation. Following the commutation
process, the multiplexed signal is applied to a pulse-amplitude modulator, the purpose of
which is to transform the multiplexed signal into a form suitable for transmission over the
communication channel.
At the receiving end of the system, the received signal is applied to a pulse- amplitude
demodulator, which performs the reverse operation of the pulse amplitude modulator. The
short pulses produced at the pulse demodulator output are distributed to the appropriate
low-pass reconstruction filters by means of a decommutator, which operates in
synchronism with the commutator in the transmitter. . This synchronization is essential

for satisfactory operation of the TDM system, and provisions have to be made for it.
1.4 BLOCK DIAGRAM
Figure 1.1 TDM Trainer Kit ST2102 Block Diagram

1.5 PRELAB QUESTIONS
1. What is multiplexing?
2. Mention the types of multiplexing?
3. What is the need for multiplexing?
4. What is the bit rate of T1,T2,T3 and T4 carrier systems?
5. Compare synchronous and asynchronous TDM.
6. What are the functions of commutator switch?
7. Give the advantages of multiplexing.
1.6 TEST PROCEDURE:
1. Take the signals from the function generator and give it to the channels (CH0 ... CH3)
present in the transmitter using patch chords. Note down the amplitude and time
period of each signal.
2. Measure the amplitude and time period at the transmitter output point.
3. Using a patch chord, connect transmitter output to receiver input.
4. For synchronization purpose, connect the transmitter clock and receiver clock and
also transmitter CH0 and receiver CH0.
5. See the output before the filter and after the filter for all the channels connected.
1.7. MODEL GRAPH:
TRANSMITTER SECTION
Figure 1.2 TDM Multiplexed Signal
MODEL GRAPH:
RECEIVER SECTION
Figure 1.3 TDM Received Signal

1.8. OBSERVATION
Transmitter Section
Signal 1
Amplitude
Time Period
Receiver Section
Demultiplexed Signal 1
Amplitude
Time Period
Signal 2
Time Period
Demultiplexed Signal 2
Amplitude
Time Period
Transmitter Output
Amplitude
Time Period
Filtered Demultiplexed Signal 1

Amplitude
Time Period
Amplitude
Filtered Demultiplexed Signal 1

Amplitude
Time Period
1.9. LAB RESULT

Time division multiplexing and de-multiplexing using PAM signals were
performed and respective waveforms were plotted.
1.10. POST LAB QUESTIONS
1. Two signals g1(t) and g2(t) are to be transmitted over a common channel by means of
time division multiplexing. The highest freq of g1(t) is 1 KHz and that g2(t) is 1.5
KHz. What is the minimum value of the permissible sampling rate? Justify your
answer.
2. How is synchronization achieved in TDM?
3. Twenty four voice signals are sampled uniformly and then time division multiplexed.
The sampling operation uses flat top samples with 1s duration. The multiplexing
operation includes provision for synchronization by adding an extra pulse of sufficient
amplitude and also 1 s duration. The highest frequency component of each voice
signal is 3.4KHz.
a. Assuming a sampling rate of 8 KHz, Find the spacing between successive
pulses of the multiplexed signal.
b. Repeat your calculation assuming the use of nyquist rate sampling.
4. What is the major drawback of digital communication?
5. Three signals m1,m2 and m3 are to be multiplexed.m1 and m2 have a 5 KHz
bandwidth and m3 has 10KHz bandwidth. Design a commutator switching system so
that each signal is sampled at its Nyquist rate.
6. Define bandwidth expansion factor.
2. PULSE CODE MODULATION AND DEMODULATION

2.1 OBJECTIVE
To analyze a PCM system and interpret
the modulated and demodulated
waveforms for a sampling frequency of 4 KHz.

2.2 HARDWARE REQUIRED
1. PCM modulator trainer kit-AET-68M
2. PCM Demodulator trainer kit-AET-68D
3. Storage oscilloscope
4. Digital multimeter
2.3 INTRODUCTION
In Pulse code modulation (PCM) only certain discrete values are allowed for the
modulating signals. The modulating signal is sampled, as in other forms of pulse
modulation. But any sample falling within a specified range of values is assigned a
discrete value. Each value is assigned a pattern of pulses and the signal transmitted by
means of this code. The electronic circuit that produces the coded pulse train from the
modulating waveform is termed a coder or encoder. A suitable decoder must be used at
the receiver in order to extract the original information from the transmitted pulse train.
This PCM system consists of
2.3.1. PCM Modulator (AET-68M):
1. Regulated power supply
2. Audio Frequency signal generator
3. Sample & Hold circuit
4. 8 Bit A/D Converter
5. 8 Bit Parallel-Serial Shift register
6. Clock generator/Timing circuit
7. DC source
2.3.2. PCM Demodulator (AET-68D):
2. 8 Bit Serial-Parallel to shift register
3. 8 Bit D/A converter
4. Clock generator
5. Timing circuit
6. Passive low pass filter
7. Audio amplifiers
2.4 BLOCK DIAGRAM
Fig 2.1. PCM Modulator AND Demodulator

Regulated power supply (68M & 68D):
This consists of a bridge rectifier followed by capacitor filters and three terminal
regulators 7805 and 7905 to provide regulated DC voltages of +5V and +12V @ 300mA
each to the on board circuits. These supplies have been internally connected to the
circuits, so no external connections are required for operation.
Audio Frequency (AF) Signal generator (68M):
Sine wave signal of 200Hz is generated to use as a modulating (message or
information) signal to be transmitted. This is an Op-Amp based Wein bridge Oscillators
using IC TL084. IC TL084 is a FET input general purpose Operational Amplifier.
Amplitude control is provided in the circuit to vary the output amplitude of AF signal.
Clock generator/Timing circuit (68M & 68D):
A TTL compatible clock signal of 64 KHz and 4KHz frequency are provided on
board to use as a clock to the various circuits in the system. This circuit is a astable
multivibrator using 555 timer followed by a buffer and frequency dividers
DC source (68M):
A 0 to +5V variable DC voltage is provided on board to use as a modulating

signal instead of AF signal. This is useful to study step by operation of PCM modulation
and demodulation. This is a simple circuit consisting of potentiometer and fixed power
supply.
Low pass filters (68D):
This is a series of simple RC networks provided on board to smoothen the output
of the D/A converter output (stair case signal). RC values are chosen such that the cutoff
frequency would be at 200Hz
Amplifiers (68D):
This is an Op-amp (IC TL084) based non-inverting variable gain amplifiers
provided on board to amplify the recovered message singles i.e. output of the Low pass
filter to desired level. Amplitude control is provided in circuit to vary the gain of the
amplifier between 0 and 3. AC/DC Switch facilitates to couple the input signal through
capacitor or directly to the amplifier input.
Sample & Hold circuit (AET-68M):
This block (circuit) is a combination of buffer, level shifting network and sample
& hold network. Op- amp IC TL084 is connected as buffer followed by non-inverting
summer circuit. One of the inputs of summer is connected a voltage divider network and
other being drawn as input. A dedicated sample& hold integrated circuit LF 398 is used
as an active component followed by buffer. The LF198/LF298/LF398 is monolithic
sample-and-hold circuits which utilize BI-FET technology to obtain ultra-high dc
accuracy with fast acquisition of signal and low droop rate. Operating as a unity gain
follower, dc gain accuracy is 0.002% typical and acquisition time is as low as 6s to
0.01%. A bipolar input stage is used to achieve low offset voltage and wide bandwidth.
Input offset adjust is accomplished with a single pin, and does not degrade input offset
drift. The wide bandwidth allows the LF198 to be included inside the feedback loop of 1
MHz op amps without having stability problems. Input impedance of 1010(Ohm) allows
high source impedance to be used without degrading accuracy.
P-channel junction FETs are combined with bipolar devices in the output
amplifier to give droop rates as low as 5mV/min with a 1f hold capacitor. The JFETs
have much lower noise than MOS devices used in previous designs and do not exhibit
high temperature instabilities. The overall design guarantees no feed-through from input
to output in the hold mode, even for input signals equal to the supply voltages.
Logic inputs on the LF198 are fully differential with low current, allowing direct
connection to TTL, PMOS, and CMOS. Differential threshold is 1.4V. The LF198 will
operate from +5V to +18V supplies.
8 Bit A/D Converter (AET-68M):
This has been constructed with a popular 8 bit successive approximation A/D
Converter IC ADC0808. The ADC0808, data acquisition component is a monolithic
CMOS device with an 8-bit analog-to-digital converter, 8-channel multiplexer and
microprocessor compatible control logic. The 8-bit A/D converter uses successive
approximation as the conversion technique. The converter features a high impedance
chopper stabilized comparator, a 256R voltage divider with analog switch tree and a
successive approximation register. The 8-channel multiplexer can directly access any of
8-single-ended analog signals. A dedicated 1MHz clock generator is provided in side this
block. For complete specifications and operating conditions please refer the data sheet of
ADC0808.
8 Bit Parallel-Serial Shift register (AET-68M):
A dedicated parallel in serial out shift register integrated circuit is used followed
by a latch The SN74LS166 is an 8-Bit Shift Register. Designed with all inputs buffered,
the drive requirements are lowered to one 74LS standard load. By utilizing input
clamping diodes, switching transients are minimized and system design simplified.
The LS166 is a parallel-in or serial-in, serial-out shift register and has a
complexity of 77 equivalent gates with gated clock inputs and an overriding clear input.
The shift/load input establishes the parallel-in or serial-in mode. When high, this input
enables the serial data input and couples the eight flip-flops for serial shifting with each
clock pulse. Synchronous loading occurs on the next clock pulse when this is low and the
parallel data inputs are enabled. Serial data flow is inhibited during parallel loading.
Clocking is done on the low-to-high level edge of the clock pulse via a two input positive
NOR gate, which permits one input to be used as a clock enable or clock inhibit function.
Clocking is inhibited when either of the clock inputs are held high, holding either input
low enables the other clock input. This will allow the system clock to be free running and
the register stopped on command with the other clock input. A change from low-to-high
on the clock inhibit input should only be done when the clock input is high. A buffered
direct clear input overrides all other inputs, including the clock, and sets all flip-flops to
zero. For complete specifications and operating conditions please refer the data sheet of
SN74LS166.
8 Bit Serial-Parallel Shift register (AET-68D):

A dedicated serial in parallel out shift register integrated circuit is used followed
by a latch. The SN74LS164 is a high speed 8-Bit Serial-In Parallel-Out Shift Register.
Serial data is entered through a 2-Input AND gate synchronous with the LOW to HIGH
transition of the clock. The device features as asynchronous Master Reset which clears
the register setting all outputs LOW independent of the clock. It utilizes the Schottky
diode clamped process to achieve high speeds and is fully compatible with all TTL
products. For complete specifications and operating conditions please refer the data sheet
of SN74LS164.
8 Bit D/A Converter (AET-68D):
This has been constructed with a popular 8 bit D/A converter IC DAC 0808. The
DAC0808 is an 8-bit monolithic digital-to-analog converter (DAC) featuring a full scale
output current settling time of 150ns while dissipating only 33mW with +5V supplies No
reference current (IREF) trimming is required for most applications since the full scale
output current is typically +1 LSB of 255 IREF/256. Relative accuracies of better than
+0.19% assure 8-bit monotonicity and linearity while zero level output current of less
than 4A provides 8-bit zero accuracy for IREF >= 2mA. The power supply currents of
the DAC0808 is independent of bit codes, and exhibits essentially constant device
characteristics over the entire supply voltage range. For complete specifications and
operating conditions please refer the data sheet of DAC0808.
PCM Operation:
Figure 2.1 shows the block diagram of the PCM system. The modulating signal is
applied to sample & hold circuit. This applied signal will be super imposed by +2.5V DC
so that the negative portion the modulating signal will clamped to positive, this process is
needed, because input of the A/D Converter should be between 0 and +5V. After level
shifting is done the signal will be passed to sample & hold circuit. Sample & hold circuit
will sample the input signal during on period of the clock signal and will hold the
sampled output till next pulse comes. Sampling rate is 4KHz in this system.
So input of the A/D Converter is a stable voltage of certain level in between 0 and
+5V. A/D converter (encoder) will give a predetermined 8 bit code for the sampled input.
This entire conversion process will be made at a fast rate as ADC0808 is operating at high
frequency clock i.e. 1MHz.
Coded output of the A/D converter is applied to input of the parallel in serial out
register through a latch (741s373). This shift register is operating at 64KHz (sampling
frequency is 4KHz, so to shift 8 bits from parallel to serial we need 64KHz). This output
(PCM) is transmitted through a co-axial cable which represents a communication channel.
PCM signal from modulator (encoder) is applied to serial to parallel register. This shift
register is also operating at 64KHz clock at which parallel to serial shift register is
operating at PCM modulator (these both the clock signals should be in synchronized with
each other in order to get proper decoded output). So the output of the serial to parallel
register is a 8 bit code. This 8 bit code is applied to 8 bit D/A converter. Output of the
D/A converter will be a staircase signaling between 0 and +5V. This stair case signal is
applied a low pass filter. This low pass will smoothen the staircase signal so that we will
get a recovered AF signal. We can use a voltage amplifier at the output of the low pass
filter to amplify the recovered AF signal to desired voltage level.
2.5 PRE LAB QUESTIONS
1. State sampling theorem.
2. What is aliasing?
3. Give the expression for aliasing error and the bound for aliasing error.
4. What is quantization?
5. What are the various steps involved in A/D conversion.
6. Define step size.
7. What is the importance of regenerative repeater?
8. List out the three basic functions of regenerative repeater.
9. What is companding?
10. Write the mean square quantization error if the step size is S.
11. What is a mid tread quantizer?
12. What is a mid rise quantizer?
2.6 TEST PROCEDURE
1. Connect the modulator trainer to the mains and switch on the power supply.
2. Observe the output of the AF generator using CRO, it should be a sine wave of 200Hz
frequency with 3Vpp amplitude.
3. Verify the output of the DC source with multimeter/scope, output should vary from 0
to +5V.
4. Observe the output of the clock generator using CRO, they should be 64KHz and
4KHz frequency of square wave with 5Vpp amplitude.
5. The clock signals are internally connected the circuit so no external connections are
required.
6. Connect the demodulator trainer to the mains and switch on the power supply.
7. Observe the output of the clock generator using CRO, it should be 64KHz square
wave with 5Vpp amplitude.
2.6.1 PCM Operation (with DC input):
Modulation:
8. Set DC source to some value say 4.4V with the help of multimeter and connect it to
the A/D converter input and observe the output LEDs
9. Note down the digital code i.e. output of the A/D converter and compare with the
theoretical value.
Theoretical value can be obtained by:
A / D Input voltage
= X (10 ) = Y( 2 )
1 LSB Value
Where
1 LSB Value
Vref/2n
Since Vref
5 V and n=8
1 LSB Value
0.01953
4.4 V
225.28(10)1
1110 0001(2)
Example:
A/D Input voltage
So digital output is 1110 0001

10. Keep CRO in dual mode. Connect one channel to 4KHz signal (one which is
connected to the Shift register) and another channel to the PCM output.
11. Observe the PCM output with respect to 4 Khz signal and sketch the waveforms.
Compare them with the given waveforms
Note: From this waveform you can observe the LSB bit enters the output first.
Demodulation
12. Connect PCM signal to the demodulators(S-P shift register) from the PCM modulator
(AET-68M) with the help of coaxial cable.
13. Connect clock signal (64KHz) from the transmitter (AET-68M) to the receiver (AET68D) using co axial cable.
14. Connect transmitter clock to the timing circuit.
15. Observe and note down the S-P shift register output data and compare it with
transmitted data(i.e. output A/D converter at transmitter).You will notice that the
output of the S-P shift register is following the A/D converter output in the modulator.
16. Observe D/A converter output (Demodulated output) using multimeter /scope and
compare it with the original signal and you can observe that there is no loss in
information in process of conversion and transmission.
Sample work sheet:
1.
2.
3.
4.
5.
Modulating signal
A/D Output (theoretical)
A/D Output (practical)
S-P Output
D/A Converter output
(Demodulated output)
:
:
:
:
:
4.4 V
1110 0001(2)
1110 0001(2)
1110 0001(2)
4.4 V
2.6.2 PCM Operation (with AC input):

Modulation:
17.
18.
19.
20.
Connect AC signal of 2Vpp amplitude to Sample & Hold circuit.

Keep the CRO in dual mode. Connect one channel to the AF signal and another
channel to the Sample & Hold output. Observe and sketch the sample & hold
output.
Connect the Sample and Hold output to the A/D converter and observe the PCM
output using Storage oscilloscope.
Observe PCM output by varying AF signal voltage.
Demodulation:
21.
22.
23.
24.
25.
26.
27.
28.
29.
Connect PCM signal to the demodulator input (AET-68D) (S-P shift register)
from the PCM modulator (AET- 68M) with the help of coaxial cable (supplied
with the trainer).
Connect clock signal (64 KHz) from the transmitter (AET-68M) to the receiver
(AET-68D) using coaxial cable.
Connect transmitter clock to the timing circuit.
Keep CRO in dual mode. Connect CH1 input to the sample and hold output
(AET-68M) and CH2 input to the D/A converter output (AET-68D)
Observe and sketch the D/A output.
Connect D/A output to the LPF input.
Observe the output of the LPF/Amplifier and compare it with the original
modulating signal (AET-68M).
From above observation you can verify that there is no loss in information
(modulating signal) in conversion and transmission process.
Disconnect clock from transmitter (AET-68M) and connect to local oscillator (i.e.,
Clock generator output from AET-68D) with remaining setup as it is.
30.
Observe D/A output and compare it with the previous result. This signal is little
bit distorted in shape. This is because lack of synchronization between clock at
transmitter and clock at receiver.
Note: You can take modulating signals from external sources. Maximum amplitude
should not exceed 4V incase of DC and 3 Vpp incase AC (AF) signals.
2.7 MODEL GRAPH:

i) With AC Input
A
M
P
L
I
T
U
D
E
I
N
V
O
L
T
S
Fig 2.2 PCM Waveform with AC input
ii)With DC Input
2.8 OBSERVATION
PCM Modulation (With AC input)
Amplitude
AC input
Sample and hold signal
Clock signal(4 KHz)
Clock signal(64 KHz)
PCM Output
PCM Demodulation (with AC input)
Time Period
Amplitude
Time Period
D/A Converter output Signal

LPF output signal
Demodulated output
PCM Modulation (With DC input)
Amplitude
Time Period
DC input
Clock signal(4 KHz)
Clock signal(64 KHz)
PCM Output
PCM Demodulation (With DC input)
Amplitude
Time Period
D/A Converter output

Signal
LPF output signal
Demodulated Output
2.9 LAB RESULT
Thus the Pulse Code modulation and demodulation were performed and graphs were
plotted.
2.10 POST LAB QUESTIONS
1. What do you mean by quantizing process?

2. What will happen when sampling rate is greater than Nyquist rate ?
3. What will happen when sampling rate is less than Nyquist rate ?
4. Find the A/D Converter output for input DC voltage of 3.6V.
5. Fig shown below shows a PCM wave in which the amplitude levels of +1 volt and -1
volt are used to represent binary symbols 1 and 0 respectively. The code word used
consists of three bits. Find the sampled version of an analog signal from which this
PCM wave is derived.
6. In digital telephony,
(a)What kind of modulation is used?

(b)Give the typical sampling rate, output data rate and speech signal Bandwidth.
7.Mention some applications of PCM.
8. What is the function of Sample and Hold circuit?
3. DIFFERENTIAL PULSE CODE MODULATION AND DEMODULATION

3.1 OBJECTIVE
To analyze a DPCM system and to interpret the modulated and demodulated

waveforms for a sampling frequency of 8 KHz.
1. ADCL-07 Kit
2. 20MHz Dual Trace Oscilloscope
3. Connecting chords
4. Power supply
NOTE: KEEP THE SWITCH FAULTS IN OFF POSITION
3.3 INTRODUCTION
Pulse Code Modulation (PCM) is different from Amplitude Modulation (AM) and
Frequency Modulation (FM) because, those tow are continuous forms of modulation.
PCM is used to convert analog signals into binary form. In absence of noise and distortion
it is possible to completely recover a continuous analog modulated signals. But in real
time they suffer from transmission distortion and noise to an appreciable extent. In the
PCM systems, groups of pulses or codes are transmitted which represent binary numbers
corresponding to modulating signal voltage levels. Recovery of transmitter information
does not depend on the height, width or energy content of the individual pulses, but only
in their presence or absence. Regeneration of the pulse is easy, resulting in the system
that produces excellent result for long distance communication.
Differential PCM is quite similar to ordinary PCM. Each word in this system
indicates the difference in amplitude, positive or negative, between this sample and the
previous sample. Thus the relative value of each sample is indicated rather than, the
absolute value in normal PCM.
This unique system consists of :
3.3.1. DPCM Modulator
1. Regulated Power Supply

2. AF Signal generator
3. Prediction Filter
4. Sample & Hold Circuit
5. A / D Converter
6. Parallel Serial Shift generator
7. Clock generator / Timing Circuit

8. DC Source
3.3.2 DPCM Demodulator
1. Regulated Power Supply

2. Serial - Parallel Shift generator
3. D / A Converter
4. Clock generator
5. Timing Circuit
6. Prediction Filter
7. Passive Low Pass Filter
3.4. BLOCK DIAGRAM / CIRCUIT DESCRIPTION
Regulated Power Supply :
This consists of a bridge rectifier followed by capacitor filters and three terminal
regulators 7805 and 7905 to provide regulated DC voltages of + 5V and +12V @ 300mA.
Each on the on-board circuits. These supplies have been internally connected to the
circuits, so no external connections are required for operation.
Audio Frequency Signal Generator :
Sine wave signal of 400HZ is generated to use as a modulating signal to be

transmitted. This is an Op-Amp based Wein Bridge Oscillators using IC TL084, which is
a FET input general purpose operational amplifier. Amplitude control is provided in the
circuit to vary the output amplitude of AF signal.
Clock Generator / Timing Circuit :
A TTL compatible clock signal of 64KHz and 8KHz frequencies are provided onboard to use as a clock to the various circuits in the system. This circuit is Astable
multivibrator using 555 timer followed by a buffer and frequency divider
DC Source :
A 0 to 290mV variable DC voltage is provided on board to use as a modulating

signal instead of AF signal. This is useful to study step by operation of DPCM
modulation and demodulation. This is a simple circuit consists of potentiometer and fixed
power supply.
Low Pass Filter :

of the D/A converter output. RC values are chosen such that the cutoff frequency would
be at 400Hz.
Sample & Hold Circuit :
This block is a combination of buffer, level shifting network and sample & hold
network. Op-amp is connected as buffer followed by non-inverting summer circuit. One
of the inputs of summer is connected a voltage divider network and other being drawn as
input.
A dedicated sample & hold integrated circuit LF 398 is used as an active
component followed by a buffer. LF398 is a monolithic sample and hold circuits, which
utilize BI FET technology to obtain ultra-high dc accuracy with fast acquisition of
signal and low droop rate. Operating as a unity gain follower, dc gain accuracy is 0.002%
typical and acquisition time is as low as 6s to 0.01%. A bipolar input stage is used to
achieve low offset voltage and wide bandwidth. Input offset adjust is accomplished with
a single pin and does not degrade input offset drift. The wide bandwidth allows the
LF398to be included inside the feedback loop of 1MHz op-amps without having stability
problems. Input impedance of 1010 ohm. Allows high source impedances to be used
without degrading accuracy. P-channel junction FETs are combined with bipolar devices
in the output amplifier to give a droop rates as low as
5mV / min with 1F hold
capacitor. The JFETS have much lower noise than MOS devices used in previous design
and do not exhibit high temperature instabilities. The overall design guarantees no feed
through from input to output in the hold mode, even for input signals equal to the supply
voltages.
Logic inputs on the LF198 are fully differential with low input current,
allowing direct connections to TTL, PMOS and CMOS. Differential threshold is 1.4V.
The LF 198 will operate from +5V to +18V supplies.
A/D Converter :
This has been constructed with a popular 8-bit successive approximations A/D
converter IC ADC0808, data acquisition component is a monolithic CMOS device with
an 8-bit A-D Converter, 8 channel multiplexer and microprocessor compatible control
logic. The 8-bit ADC uses successive approximation as the conversion technique. The
converter features a high impedance chopper stabilized comparator., 256R voltage divider
with analog switch tree and a successive approximation register.
multiplexer can directly access any 8-single-ended analog signals.
The 8-channel
Parallel-Serial Shift Register
A dedicated parallel in serial out shift register integrated circuit is used followed
by a latch. The SN74LS166 is an 8-bit Shift register. Designed with all inputs buffers, the
drive requirements are lowered to one 74LS standard load. By utilizing input clamping
diodes, switching transients are minimized and system design simplified. The LS166 is a
parallel in or serial out shift register, serial-out shift register and has a complexity of 77
equivalent gates with gated clock inputs and an overriding cleat input. The shift / load
input establishes the parallel in or serial-in mode. When high, this input enables the
serial data input and couples the eight flip flops for serial shifting with each clock pulse.
Synchronous loading occurs on the next clock pulse when this is low and the parallel data
inputs are enabled. Serial data flow is inhibited during parallel loading. Clocking is done
on the low-to-high level edge of the clock pulse via a two input positive NOR gate, which
permits one input to be used as a clock enable or clock inhibit funation. Clocking is
inhibited when either of the clock inputs is held high; holding either input low enables the
other clock input. This will allow the system clock to be free running and the register
stopped on command with the other clock input. A Change from low- to high on the
clock inhibit input should only be done when the clock input is high. A buffered direct
clear input overrides all other inputs. Including the clock, and sets all flip-flops to zero.
For complete specifications and operating conditions please refer the data sheet of
SN74LS166
Serial-Parallel Shift Register :
A dedicate serial in parallel out shift register integrated circuit is used followed by
a latch. The SN74LS164 is a high speed 8 Bit Serial-In Parallel-Out Shift Register. Serial
data is entered through a 2-Input AND gate synchronous with the LOW to HIGH
transition of the clock. The device features an asynchronous Master Reset, which clears
the register setting all outputs LOW independent of the clock. It utilizes the Schottky
diode clamped process to achieve high speeds and is fully compatible with all TTL
products. For complete specifications and operating conditions please refer the data sheet
of SN74LS164.
D/A converter :
This has been constructed with a popular 8 bit D/A Converter IC DAC 0808. The
DAC0808 is an 8-bit monolithic digital-to-analog converter (DAC) featuring a full scale
output current settling time of 150 ns while dissipating only 33m W with 5V supplies.
BLOCK DIAGRAM
Fig 3.1 Block diagram of DPCM System
Reference current (IREF) trimming is required for most applications since the full scale
output current is typically 1 LSB of 255 IREF/ 256. Relative level output current of less
than 4A provides 8-bit zero accuracy for IREF >=2mA. The power supply current of the
DAC0808 is independent of bit codes and exhibits essentially constant device
characteristics over the entire supply voltage range. For complete specifications and
operating conditions please refer the data sheet of DAC0808.
DPCM Operation:
The modulating signal is applied to positive terminal of the summer circuit and
the output pf the prediction filter is connected to negative terminal of the summer circuit.
The output of the summer circuit is connected to the sample & hold circuit. Sample &
hold circuit will sample the input signal during ON period of the clock signal and will
hold the sampled output till next pulse comes. Sampling rate is 8KHz in this system.
So input of the A/D converter is stable voltage of certain level in between 0 and +
280mV. A/D converter will give a predetermined 4-bit code for the sampled input. This
entire conversion process will be made at a fast rate as ADC 0808 is operating at high
frequency clock.
Coded output of the ADC is applied to input of the parallel in serial out register
through a latch (74LS373). This shift register is operating at 64KHZ. This output is
transmitted through a coaxial cable, which represent a communication channel.
DPCM signal from modulator is applied to serial to parallel register. This shift
register is also operating at 64KHz clock to which parallel to serial shift register is
operating at DPCM modulator. So the output of the serial to parallel register is a 4-bit
code.
This 4-bit code is applied to D/A converter. Output of the DAC will be a staircase
signal lying between 0 and +280mV. This stair case signal is applied a low pass filter.
This low pass will smoothen the stair case signal so that we will get a recovered AF
signal.
3.5. PRELAB QUESTIONS:
1. Compare DPCM and PCM.

2. What is the significance of predictor in DPCM?
3. How is a predictor constructed?
4. What is prediction error?
5. What is the significance of accumulator in DPCM?
6. Why DPCM is used for speech compression?
3.6. TEST PROCEDURE
DPCM modulation:
1. Refer to the block diagram and carry out the following Connections and switch
settings.
2. Connect power supply in proper polarity to the kit ADCL-07 and switch it ON.
3. Keep the clock frequency at 512 KHz by changing the jumper position of JP1
in the clock generator section
4. Keep the amplitude of the onboard sine wave, of frequency 500Hz to 1Vpp DPCM
modulation.
5. Connect the 500Hz sine wave to the lN post of Analog Buffer.
6. Connect OUT post of Analog Buffert o lN post of DPCM modulator section.
7. Observe the sample output at the given test point the input signal is sampled at the
clock frequency of 16KHz.
8. Observe the linear predictor output at the PREDICTED OUT post of the Linear
predictor in the DPCM modulator section.
9. Observe the differential pulse code modulate data( DPCM) at the DPCM OUT post of
the DPCM modulator section.
10. Observe the DPCM data at DPCM OUT post by varying input signal from to 2V.
DPCM demodulation:
1. Connect the DPCM modulated data from the DPCM OUT post of the DPCM
Modulator to the lN post of the DPCM demodulator.
2. Observe the demodulated data at the output of summation block.

3. Observe the integrated demodulated data at the DEMOD OUT post of the DPCM
demodulator.
4. Connect the demodulated data from the DEMOD OUT post of the DPCM
demodulator to the lN post of the low-pass filter.
5. Observe the reconstructed signal at the OUT post of the filter.Use RST switch for
clear observation of output.
6. Now, simultaneously reduce the clock frequencies f rom 512KHz to 256KHz,128KHz
and 64KHz by changing the jumper position of JP1 and observe the difference in the
DPCM modulated and demodulated data.As the frequency of clock decreases DPCM
demodulated data at DEMOD OUT becomes distorted.
7. Observe various waveform as mentioned below
3.7. MODEL GRAPH
Fig.3.2 DPCM OPERATION (with AC input) MODULATION &

DEMODULATION
3.8. Observation:
ON KIT ADCL-07
Observe the following waveforms on the oscilloscope and plot on the paper.
1. 500Hz ,lV pp input sine wave.
2. Sampled out at the provided test point SAMPLER OUT
3. Linear predictor out at PREDICTED OUT post.
4. DPCM data at DPCM OUT post
5. Line interface out at the given output test point of line interface block in
DPCM Demodulator
6. Demodulated DPCM data at the output test point of summation block in
DPCM demodulator.
7. Integrated demodulated data at the DEMOD OUT post of the DPCM
demodulator
8. Reconstructed sine wave at the OUT post of the filter
9. Observe the data at different clock rates.
DPCM Operation - with AC input
Modulation
Amplitude
Time Period
AC Input
Prediction Filter Output
Sample and Hold Output
Clock 1 Output
DPCM Output
Demodulation
Amplitude
DPCM Input
D/A Converter Output
LPF Output
Demodulated output
Prediction Filter Output
Time Period
3.9. LAB RESULT
Thus the Differential Pulse code modulation and demodulation were performed.
3.10 POST LAB QUESTIONS:
1. For data compression say whether ADPCM or DPCM is better. Justify.

2. What is the need for compression?Mention the types of compression.
3. List the communication standards which use DPCM.
4. Based upon the knowledge that you have gained after doing the experiment write the
functions of sample and hold circuit.
5. Name the circuit used to achieve synchronization between transmitter and receiver.
5. DELTA MODULATION AND DEMODULATION

4.1. OBJECTIVE
To analyze a Delta modulation system. and interpret the modulated and demodulated
waveforms
1.
PCM Modulator trainer- AET-73M
2.
PCM Demodulator trainer-AET-73D
3.
Storage Oscilloscope
4.
Digital Multimeter
5.
Co-axial cables (standard accessories with AET-73 trainer)
4.3. INTRODUCTION
Delta Modulation is a form of pulse modulation where a sample value is

represented as a single bit. This is almost similar to differential PCM, as the transmitted
bit is only one per sample just to indicate whether the present sample is larger or smaller
than the previous one. The encoding, decoding and quantizing process become extremely
simple but this system cannot handle rapidly varying samples. This increases the
quantizing noise.
The trainer is a self sustained and well organized kit for the demonstration of delta
modulation & demodulation .The system consist of :
4.3.1. DM Modulator (AET-73M) trainer kit

2. Audio Frequency signal generator
3. Buffer/signal shaping network
4. Voltage comparator
5. 4 Bit UP/DOWN counter
6. Clock generator/Timing circuit
8. DC source
4.3.2. DM Demodulator (AET-73D) trainer kit

2. 4 Bit UP/DOWN counter
4. Clock generator
5. Passive low pass filter
6. Audio amplifier
Regulated power supply (73M & 73D):
This consists of a bridge rectifier followed by Capacitor filters and three terminal
regulators 7805 and 7905 to provide regulated DC voltages of +-5V and +12V@ 300mA
each to the on board circuits. These supplies have been internally connected to the
circuits. so no external connections are required for operation.
Audio Frequency (AF) S signal generator (73M):
Sine wave signal of 100 Hz is generated to use as a modulating (message or

information) signal to be transmitted. This is an Op-Amp based Wein bridge Oscillators
using IC TL084 is a FET.input general purpose Operational Amplifier .Amplitude control
is provided in the circuit to vary the output amplitude of AF signal.
Clock generator/Timing circuit (73M & 73D):
A TTL compatible clock signal of 4 KHz frequency is provided on board to use as

a clock to the various circuits in the system. This circuit is a astable multivibrator using
555 timer followed by a buffer.
DC Source (73M):
A 0 to +5V variable DC voltage is provided on board to use as a modulating

signal instead of AF Signal. is useful to study step by step operation of Delta modulation
and Demodulation. This is a simple circuit consists of potentiometer and fixed power
supply.
Buffer/Signal shaping circuit (73M):
A non inverting buffer using IC TL 084 is provided at the input of the DM
modulator followed by a level shifting network. Buffer provides the isolation between
DM circuit and the signal source. Signal Shaping super imposes the 1.5V DC on
incoming modulating signal so that the input of the comparator lies between 0 and +3V
maximum.
4.4.BLOCK DIAGRAM
Fig.4.1. DM Modulator
Fig.4.2. DM Demodulator
Voltage comparator (73D):
This circuit is build with IC LM339 The LM339 series consists of four
independent precision voltage comparators with an offset voltage specification as low as
2mV for all four comparators. These were designed specifically to operate from a single
power supply over a wide range of voltages .Operation from split power supplies is also
possible and the low power supply current drain is independent of the magnitude of the
power supply voltage. These comparators also have a unique characteristic in that the
common mode voltage range includes ground, even though operated from a single power
supply voltage. Application areas include limit comparators simple analog to digital
converters: pulse, square and time delay generators. wide range VCO; MOS clock timers;
multivibrators and high voltage digital logic gates .The LM139 series was designed to
directly interface with TTL and CMOS. When operated from both plus and minus power
supplies, they will directly interface with MOS logic where the low power drain of the
LM339 is a distinct advantage over standard comparators .For circuit connections and
other operating conditions.
Low pass filters (73D):

of the D/A converter output. RC values are chosen such that the cutoff frequency would
be at 100 Hz.
Amplifiers (73D):
This is an Op-amp (IC TL084) based non-inverting variable gain amplifiers

provided on board to amplify the recovered message singles i.e. output of low pass filter
to desired level. Amplitude control is provided in circuit to vary the gain of the amplifier
between 0 and 6.AC/DC Switch facilitates to couple the input signal through capacitor to
directly to the amplifier input.
4 Bit UP/DOWN Counter (73M & 73 D):
This circuit is made using Synchronous 4-Bit Up/Down Counter with Mode
Control IC 74LS191 .The DM 74LS191 circuit is a synchronous, reversible, counter.
Synchronous operation is provided by having all flip-flops clocked simultaneously. so
that the outputs change simultaneously when so instructed by the steering logic. This
mode of operation eliminates the output counting spikes normally associated with the
asynchronous counters. The outputs of the four master slave flip flops are triggered on a
LOW to HIGH level transition of the clock input. if the enable input is LOW a HIGH at
the enable input inhibits counting .Level changes at either the enable input or the down/up
input should be made only when the clock input is HIGH. The direction of the count is
determined by the level of the down/up input. When LOW the counter counts up and
when HIGH it counts down. The counter is fully programmable that is the outputs may be
preset to either level by placing a LOW on the load input and entering the desired data at
the data inputs. The output will change independent of the level of the clock input. This
feature allows the counters to be used as modulo-N dividers by simply modifying the
count length with the preset inputs. The clock, down/up and load inputs are buffered to
lower the drive requirement which significantly reduces the number of clock drivers
required for parallel words. The ripple clock input produces a low level output pulse
equal in width to the low level portion of the clock input when an overflow or underflow
condition exists. The counters can be easily cascaded by feeding the ripple clock output to
the enable input of the succeeding counter if parallel clocking is used, or to the clock
input if parallel enabling is used. The maximum/minimum count output can be used to
accomplish look-ahead for high speed operation.
4 Bit D/A converter (AET-73M & 73D):
This has been constructed with a popular 8 bit D/A Converter IC DAC 0808.The
DAC0808 is an 8-bit monolithic DAC featuring a full scale output current settling time of
150 Ns while dissipating only 33 maw with +-5V supplies. No reference current (I
REF)
trimming is required for most applications since the full scale output current is typically
+- 1 LSB of 255 I
REF/256
.Relative accuracies of better than +- 0.19 % assure 8 bit
monotonic and linearity while zero level output current of less than 4 A provides 8-bit
zero accuracy for I
REF
[ greater than or equal ] 2 math power supply currents of the
DAC0808 is independent of bit codes, and exhibits essentially constant device

characteristics over the entire supply voltage range.4 LSB Bits are permanently grounded
to make 4 bit converter. For complete specifications and operating conditions please refer
the data sheet of DAC0808.
DM Operation:
Figure 4.1 shows the basic block diagram of the PCM system. The modulating
signal is applied to buffer /signal shaping network. This applied signal will be
superimposed by +1.5V DC so that the negative portion the modulating signal will
clamped to positive ,this process is needed ,because input of the comparator should be
between 0 and +3V.
After level shifting is done the signal will be passed to inverting input of the
comparator. on inverting input of the comparator is connected to output of the 4 Bit D/A
converter. Comparator is operating at +5V single supply .So output of the comparator will
be high (i.e. +vet Vast) when modulating signal is less than the reference signal i.e. D/A
output, otherwise it will be 0V. And this signal is transmitted as DM signal .same signal
is also connected as UP/DOWN control to the UP/DOWN counter (74LS 191).
UP/DOWN counter is programmed for 0000 starting count. So initially output of
the counter is at 0000 and the D/A converter will be at 0V .Comparator compares the
modulating signal is greater than the reference signal. For next clock pulse depending on
the UP/DOWN input counter will count up or down. If the UP/DOWN input is low
(nothing but comparator output).
Counter will make up and output will be 0001. So the D/A converter will convert
this 0001 digital input to equivalent analog signal(i.e. 0.3V 1 LSB Value).Now the
reference signal is 0.3V.If still modulating signal is greater than the D/A output again
comparator output(DM) will be low and UP count will occur. If not DOWN Count will
take place. This process will continue till the reference signal and modulating signal
voltages are equal. So DM signal is a series of 1 and 0.
DM signal is applied to a UP/DOWN input of the UP/DOWN counter at the
receiver. This UP/DOWN counter is programmed for 1001 initial value (i.e. power on
reset) and mode control is activated. So depend on the UP/DOWN input for the next
clock pulse counter will count UP or DOWN. This output is applied to 4 Bit D/A
converter. A logic circuit is added to the counter which keeps the output of the counter in
between 0000 to 1111 always. Output of the D/A converter will be a staircase signal lies
between 0 and +4.7V.This staircase signal is applied a low pass filter .This low pass will
smoothen the staircase signal so that original AF signal will be recovered.
We can use a voltage amplifier at the output of the low pass filter to amplify the
recovered AF signal to desired voltage level.
4.5. PRELAB QUESTIONS
1. What are two types of quantization errors?

2. What is granular noise?
3. What is slope overload distortion ?
4. What happens to the output signal if the variation of the message signal is
(i)greater than the step size (ii) less than the step size
5. What is the advantage of delta modulation over PCM?
4.6. TEST PROCEDURE:
DM Modulator:
1. Study the theory of operation

2. Connect the trainer (AET-73M) 3. Observe the output of AF generator using CRO; it should be a Sine wave of 100 Hz
frequency with 3Vpp amplitude.
4. Verify the output of the DC source with multimeter/scope; output should vary 0 to
+4V
5. Observe the output of the clock generator using Crotchety should be 4 KHz frequency
of square wave with 5 Up amplitude.
Note: This clock signal is internally connected to the up/down counter so no external
connection is required.
DM With DC Voltage as modulating signal:
6. Connect DC signal from the DC source to the inverting input of the comparator and
set some voltage says 3V.
7. Observe and plot the signals at D/A converter output (i.e. non-inverting input of the
comparator), DM signal using CRO and compare them with the waveforms given in
figure.
8. Connect DM signal (from 73M) to the DM input of the demodulator.
9. Connect clock (4KHz) from modulator (73M) to the clock input of the demodulator
(73D). Connect clock input of UP/DOWN counter (in 73D) to the clock from
transmitter with the help of springs provided.
10. Observe digital output (LED indication) of the UP/DOWN counter (in 73 D) and
compare it with the output of the UP/DOWN (in 73M) .By this you can notice that the
both the outputs are same.
11. Observe and plot the output of the D/A converter and compare it with the waveforms
given in figure.
12. Measure the demodulated signal (i.e. output of the D/A converter 73D with the help
of multimeter and compare it with the original signal 73 M. From the above
observation you can notice that both the voltages are equal and there is no loss in
process of modulation, transmission and demodulation.
13. Similarly you can verify the DM operation for different values of modulating signal.
DM With AF Voltage as modulating signal:
14. Connect AF signal from the AF source to the inverting input of the comparator and
set ome voltage says 3V.
15. Observe and plot the signals at D/A converter output (i.e. non-inverting input of the
comparator), DM signal using CRO and compare them with the waveforms given in
figure.
16. Connect DM signal (from 73M) to the DM input of the demodulator.
17. Connect clock (4KHz) from modulator (73M) to the clock input of the demodulator
(73D).
18. Connect clock input of UP/DOWN counter (in 73D) to the clock from transmitter
with the help of springs provided.
19. Observe and plot the output of the D/A converter and compare it with the waveforms
given in figure.
20. Observe and sketch the D/A output.

21. Connect D/A output to the LPF input.
22. Observe the output of the LPF/Amplifier and compare it with the original modulating
signal (AET-73M).
23. From the above observation you can verify that there is no loss in information in
conversion and transmission process.
24. Disconnect clock from transmitter (AET-73M) and connect to local oscillator (i.e.
clock generator output from AET-73D) with remaining setup as it is. Observe
demodulated signal output and compare it with the previous result. This signal is little
bit distorted in shape. This is because lack of synchronization between clock at
transmitter and clock at receiver.
Note: you can take modulating signals from external sources. Maximum amplitude
should not exceed 4 V incase of DC and 3 Vpp incase of AC (AF) signals.

4.7.MODEL GRAPH
Fig 4.3 DM Waveforms for AC input signal
4.8.OBSERVATION
DM Modulation (With AC input)
Amplitude
AC input
Clock signal(4 KHz)
DM Output
Time Period
DM Demodulation (with AC input)

Amplitude
Time Period
DM input
Demodulated Output
Clock signal(4 KHz)
DM Modulation (With DC input)

Amplitude
Time Period
DC input
Clock signal(4 KHz)
DM Output
DM Demodulation (With DC input)
Amplitude
Time Period
DM input
Demodulated Output
Clock signal(4 KHz)
4.9. LAB RESULT
Thus the Delta modulation and demodulation were performed and graphs were
plotted.
4.10. POST LAB QUESTIONS:
1. Compare DPCM ,PCM& Delta modulation.

2. How to reduce the quantization noise that occurs in DM?
3. A band pass signal has a spectral range that extends from 20 to 82 KHz.Find the
acceptable sampling frequency.
4. Find the fourier series expansion of an Impulse train.
5. Mention the applications of DM.
5. FSK MODULATION AND DEMODULATION

5.1 OBJECTIVE
To analyze a FSK modulation system. and interpret the modulated and demodulated
waveforms
1. FSK Trainer Kit - AET-48

2. Dual Trace oscilloscope
3. Digital Multimeter
5.3 INTRODUCTION
In Frequency shift keying, the carrier frequency is shifted (i.e. from one frequency to
another) corresponding to the digital modulating signal. If the higher frequency is used to
represent a data 1 & lower frequency a data 0, the resulting FSK waveform appears.
Thus
Data =1 High Frequency
Data =0 Low Frequency
It is also represented as a sum of two ASK signals. The two carriers have different
frequencies & the digital data is inverted. The demodulation of FSK can be carried out by
a PLL. As known, the PLL tries to lock the input frequency. It achieves this by
generating corresponding O/P voltage to be fed to the VCO, if any frequency deviation at
its I/P is encountered. Thus the PLL detector follows the frequency changes and generates
proportional O/P voltage. The O/P voltage from PLL contains the carrier components.
Therefore to remove this, the signal is passed through Low Pass Filter. The resulting
wave is too rounded to be used for digital data processing. Also, the amplitude level may
be very low due to channel attenuation.
5.3.1 FSK Modulator
Figure 5.1 shows the FSK modulator using IC XR 2206. IC XR 2206 is a VCO
based monolithic function generator capable of producing Sine, Square, Triangle signals
with AM and FM facility. In this trainer XR2206 is used generate FSK signal. Mark
(Logic 1) and space (logic 0) frequencies can be independently adjusted by the choice of
timing potentiometers FO & Fl. The output is phase continuous during transitions. The
keying signal i.e. data signal is applied to pin 9.
Figure 5.1
5.3.2 FSK Demodulator:
Figure 5.2 shows FSK demodulator in a combination of PLL (LM565) and

comparator (Op-amp). The frequency-changing signal at the input to the PLL drives the
phase detector to result in rapid change in the error voltage, which is applied to the input
of the comparator. At the space frequency, the error voltage out of the phase detector is
below the comparison voltage of the comparator. The comparator is a non-inverting
circuit, so its output level is also low. As the phase detector input frequency shifts low (to
the mark frequency), the error voltage steps to a high level, passing through the
comparison level, causing the comparator output voltage to go high. This error voltage
change will snap the comparator output voltage between its two output levels in manner
that duplicates the data signal input to the XR22OS modulator.
The free running frequency of the PLL (no input signal) is set midway between
the mark and space frequencies. A space at 2025 Hz and mark at 2225 Hz will have a free
running VCO frequency of 2125 Hz.
5.4 FSK SYSTEM DIAGRAM
Figure 5.3
1.
List some applications of FSK.
2. Define digital modulation schemes.

3. Identify the differences between Pass band and Base band Communication.
4. What is a matched filter?
5. What are the properties of matched filter?
5.6 TEST PROCEDURE
1.
Connect the trainer kit to the mains and switch on the power supply
2.
Check internal RPS voltage (it should be 12V) and logic source voltage for logic one
(it should be 12V)
3.
Observe the data signal using oscilloscope. Note down the value. (Amplitude and
Time Period)
4.
Connect the output of the logic source to data input of the FSK modulator
5.
Set the output frequency of the FSK modulator as 1.2KHz using control F0 (this
represents logic 0). Then set another frequency as 2.4KHz using control F1 (this
represents logic 1) using multimeter.
6.
Connect the data input of the FSK modulator to the output of the data signal
generator. Observe the signal that comes out of FSK modulator and note down the
readings.
7.
Connect the FSK modulator output to the input of the FSK demodulator. Observe the
waveform of FSK demodulator output using CRO and note down the readings.
5.7 OBSERVATION
Signal Type
Data source
Time
Period
Amplitude
F1
F0
Square
wave
Signal
Name
FSK
Signal Name
Modulated Output
Frequency Amplitude
1.2KHz and
2.4KHz
alternately
appearing
Carrier signal
Frequency
Amplitude
2.4KHz
1.2KHz
Demodulated output
Signal Type
Time
Amplitude
Period
Square wave
5.8 MODEL GRAPH
Figure 5.4
5.9 LAB RESULT
Thus the FSK modulation and demodulation were performed and required graphs
were plotted.
1. What is MSK?
2. For the given 8 bit data 10111010 draw the FSK output waveform.
3. Draw the constellation diagram of FSK.
4. What will happen if the same frequency is used for both the carriers?
6. PSK MODULATION AND DEMODULATION

6.1 OBJECTIVE
To analyze a PSK modulation system. and interpret
the modulated and
1.
PSK Trainer Kit - AET-71
2.
Dual Trace oscilloscope-POS-2020
3.
Digital Multimeter
6.3 INTRODUCTION
Phase shift keying is a modulation/data transmitting technique in which phase of the

carrier signal is shifted between two distinct levels. In a simple PSK(ie binary PSK)
unshifted carrier Vcos0t is transmitted to indicate a 1 condition, and the carrier shifted
by 1800 ie Vcos0t is transmitted to indicate as 0 condition.
6.3.1 PSK Modulator
Figure 6.2shows the PSK modulator. IC CD 4052 is a 4 channel analog multiplexer

and is used as an active component in this circuit. One of the control signals of 4052 is
grounded so that 4052 will act as a two channel multiplexer and other control is being
connected to the binary signal ie data to be transmitted. Unshifted carrier signal is
connected directly to CH1 and carrier shifted by 1800 is connected to CH2.phase shift
network is a unity gain inverting amplifier using OP-amp (TL084).
When input data signal is 1 ie control signal is at high voltage, output of the 4052 is
connected to CH1 and unshifted (or 0 phase)carrier is passed on to output. Similarly
When data signal is 0 ie control signal is at zero voltage output of 4052 is connected to
CH2 and carrier shifted by 1800 is passed on to output.
6.3.2 PSK Demodulator:
Demodulation of PSK is achieved by subtracting the received carrier from a

derived synchronous reference carrier of constant phase. Figure shows the simple
coherent(synchronous) PSK demodulator.
Received PSK signal is converted to square wave using an op-amp(TL084) based
zero crossing detector and connected to EX-OR circuit. The derived reference carrier is
connected to other input of the EX-OR Gate through an op-amp based zero crossing
detector. For the simplicity same carrier is used at receiver as reference carrier (In
practical communication system reference carrier is generated at receiver).We can

observe the exact operation of demodulator with the help of waveforms at various nodes
in the circuit.
CIRCUIT DIAGRAM
Fig 6.1. Phase Shift Keying
Fig 6.2 PSK Modulator
Fig 6.3 PSK Demodulator
Received PSK signal is converted to square wave using an op-amp(TL084) based

zero crossing detector and connected to EX-OR circuit. The derived reference carrier is
connected to other input of the EX-OR Gate through an op-amp based zero crossing
detector. For the simplicity same carrier is used at receiver as reference carrier (In
practical communication system reference carrier is generated at receiver).We can
observe the exact operation of demodulator with the help of waveforms at various nodes
in the circuit.
1. What are the applications of PSK?

2. What are antipodal signals?
3. Give the equation for average probability of symbol error for coherent binary PSK.
4. Explain how QPSK differs from PSK in terms of transmission bandwidth and bit
information it carries
5. Draw the constellation diagram for PSK.
6.6 PROCEDURE
1. Connect the trainer to mains and switch on the power supply.

2. Measure the output of the regulated power supply ie +5V and -5V with the help of
digital multimeter.
3. Observe the output of the carrier generator using CRO, it should be an 8KHZ sine
with 5Vpp amplitude.
4. Observe the various data signals(1KHZ,2KHZ and 4KHZ0 using CRO
6.6.1 Modulation:
5. Connect carrier signal to carrier input of the PSK modulator.

6. Connect data signal say 4KHZ from data source to data input of the modulator.
7. Keep CRO in dual mode and connect CH1 input of the CRO to data signal and CH2
to the output of the PSK modulator.
8. Observe the PSK output signal with respect to data signal and plot the waveforms.
6.6.2 Demodulation:
9. Connect the PSK output to the PSK input of the demodulator.

10. Connect carrier to the carrier input of the PSK demodulator.
11. Keep CRO in dual mode and connect CH1 to data signal(at modulator) and CH2 to
the output of the demodulator.
12. Compare the demodulated signal with the original signal. By this we can notice that
there is no loss in modulation and demodulation process
13. Repeat the steps 6 to 12 with different data signals ie 2KHZ and 1KHZ
6.7 MODEL GRAPH
Fig 6.4. PSK Waveforms for different data input signals
6.8 OBSERVATION
PSK (Modulation) -AC signal
Amplitude
Time Period
Amplitude
Time Period
Carrier signal
Data source
For 4KHz
For 2KHz
For 1KHz
Modulated output
For 4KHz
For 2KHz
For 1KHz
Demodulation
Demodulated output
For 4KHz
For 2KHz
For 1KHz
6.9 LAB RESULT
Thus the PSK modulation and demodulation were performed and graphs were
plotted.
1. Compare FSK and PSK.

2. List the Characteristics of TL084 op-amp.
3. Compare TL084 op amp with IC 741 op amp.
4. What do we infer from constellation diagrams of various modulation schemes.
7. DATA FORMATTING
7.1. OBJECTIVE
To identify the various encoding schemes for a given data stream.

1. Coding Kits.
2. CRO
7.3. INTRODUCTION
1 and 0 can be represented in various formats in different levels and

waveforms. The selection of coding technique depends on system band width, systems
ability to pass dc level information, error checking facility.
Non return to Zero (level):
The NRZ(L) waveform simply goes low for one bit time to represent a data 0
and high to represent data 1.For lengthy data the clock is lost in
asynchronous mode.
The maximum rate at which NRZ can change is half the data clock.[when alternate 0s
and 1s are there.
DC Level:
A length data will have only a dc level as its waveform, a dc voltage cannot be
used in circuits which involve transformers like telephone, AC coupled amplifiers,
capacitors,
filter etc.
Manchester Biphase:
0 is encoded low during first half of bit time & high for other half of bit & vice
versa for 1.There is no synchronization problem in the receiver. It is independent of DC
levels, since there is a transition occurring in each bit. Its max frequency is equal to data
clock rate. There is at least one transition per bit. Since there is midway transition, it
makes clock regeneration difficult so we use special bi phase clock recovery circuit
7.4 MODEL GRAPH
Fig 7.1 Data Encoding Schemes

Return to Bias:
It is a 3 level code it consist of positive, negative and zero. Easy clock

synchronization is possible.1 for positive,0 for negative in first half and zero bias for
second half. Maximum frequency is equal to data clock frequency. DC levels of
waveforms depends on strings of 1s and 0s.Hence we cannot use AC coupled
communication link. Timing information is easily obtained. The system is referred to as
self clocking system, as magnitude of waveform is original data signal. It requires
complex transmitters.
7.5 PRELEB QUESTIONS
1. Compare NRZ-I and NRZ- L .

2. What is the use of data formatting?
3. Compare NRZ and biphase encoding .
4. What is the relationship between quantization levels and number of bits in a code
word?
5. Give the advantages of Manchester encoding.
7.6.TEST PROCEDURE
1. Connect the data generator output to code generator kit. This gives the random binary
sequence o the kit.
2. Connect the clock signal to the trainer kit.
3. Connect the output to the CRO channel along with the clock signal.
4. Observe the waveforms with respect to clock on a dual channel CRO, and compare
with the model graph.
5. Plot the waveforms for different codes.
7.7 LAB RESULT
Thus the different coding techniques were studied and observed for a given binary
data, and their corresponding waveforms plotted.
7.8. POST LAB QUESTIONS
1. Assume a data stream is made of ten 0s. Encode this stream using the following
encoding schemes. How many change can you find for each scheme?
a)NRZ
b)RZ
c)Bi phase
2. If the bit rate of a signal is 1000 bits/seconds, how many bits can be sent in 4
seconds? How many bits in 1/5 seconds? How many in 100 milli seconds?
3. List out the merits & demerits of each data formats .
4. Represent the given data 11010100 in Manchester encoding and NRZ M scheme.
8. Amplitude Shift Keying

8.1 OBJECTIVE
To simulate Binary Amplitude shift keying technique using MATLAB software

8.2 SOFTWARE REQUIRED
MATLAB ,Computer installed with Windows XP or higher Version.

8.3 PREPARATION (PRE-LAB)
1. Given a bandwidth of 5000 Hz for an ASK signal, what are the baud rate and bit rate?
2. Find the minimum bandwidth for an ASK signal transmitting at 2000bps.
8.4 MATLAB INTRODUCTION
MATLAB is a programming language and numerical computing environment.

The name MATLAB is an acronym for Matrix Laboratory. As it name suggests it
allows easy manipulation of matrix and vectors. Plotting functions and data is made easy
with MATLAB. It has a good Graphic User Interface and conversion of matlab files to
C/C++ is possible. It has several toolboxes that possess specific functions for specific
applications. For example Image Processing, Neural Networks, CDMA toolboxes are
name a few. An additional package, Simulink, adds graphical multidomain simulation and
Model-Based Design for dynamic and embedded systems. Simulink contains Blocksets
that is analogous to Toolboxes.It was created by Mathworks Incorporation, USA.
MATLAB has become a defacto programming language for Engineers. Writing
MATLAB programs for modulation applications require knowledge on very few
functions and operators. The operators mostly used are arithmetic operators and matrix
operators. To know more type in the command prompt help ops. MATLAB will give a
list in that to know on specific operator say addition type in the command prompt help
plus. MATLAB will give how to use and other relevant information. Commonly used
graphical functions are plot, figure, subplot, title, and mathematical functions are sin and
cos only. The mathematical functions sin and cos are self explanatory. The graphical
function figure will create a new window and then subsequent graphical commands can
be applied. The plot function usually takes two vectors and plot data points according to
given vector data. In this case it will time Vs signal. Subplot function is used when two or
more plots are drawn on the same figure. As title function suggests it helps to write title
of the graph in the figure. For further details type help plot or help subplot in the
command prompt and learn the syntax.
8.5 THEORY
Amplitude Shift Keying
ASK is a form of modulation that represents digital data as variations in the

amplitude of a carrier wave.The amplitude of an analog carrier signal varies in
accordance with the bit stream (modulating signal), keeping frequency and phase
constant.
On-off keying (OOK) the simplest form of amplitude-shift keying (ASK)
modulation that represents digital data as the presence or absence of a carrier wave. In its
simplest form, the presence of a carrier for a specific duration represents a binary one,
while its absence for the same duration represents a binary zero.
In a ASK system, the pair of signal S1(t) used to represent binary symbols 1 & 0
are defined by
S1 (t) = 2Eb/b Cos 2fct
0
where 0 t< Tb and
Eb = Transmitted signed energy for bit
The carrier frequency fc =n/Tb for some fixed integer n.
Block Diagram of ASK Transmitter
Fig 8.1 ASK Transmitter block diagram
The input binary symbols are represented in polar form with symbols 1 & 0
represented by constant amplitude levels Eb & -Eb. This binary wave is multiplied by a
sinusoidal carrier in a product modulator. The result is a ASK signal.
ASK Receiver
Fig 8.2 ASK Receiver block diagram
The received ASK signal is applied to a correlator which is also supplied with a
locally generated reference signal 1 (t). The correlated o/p is compared with a threshold
of zero volts. If x1> 0, the receiver decides in favour of symbol 1. If x1< 0, it decides in
favour of symbol 0
8.6 ALGORITHM
ASK Modulation
4. Generate the carrier signal (1 (t) = 2/Tb cos 2fct )

5. Generate the base band data signal .
6. Multiply the polar form data signal and carrier signal. The resultant signal is a PSK
signal.
7. Plot the carrier, data and PSK signal.
ASK Demodulation
4. Multiply the received PSK signal with the carrier signal (1 (t) = 2/Tb cos 2fct )
5. Integrate the resultant signal(x1) .
6. If x1 is greater than zero then choose 1 and if it is less than 0 choose 0.
7. Plot the demodulated signal.
8.7 TEST PROCEDURE
1. Open the MATLAB software by double clicking its icon.

2. MATLAB logo will appear and after few moments Command Prompt will appear.
3. Go to the File Menu and select a New M- file. (File
New M-file) or in the left hand
corner a blank white paper icon will be there. Click it once.

4. A blank M- file will appear with a title untitled
5. Now start typing your program. After completing, save the M- file with appropriate
name. To execute the program Press F5 or go to Debug Menu and select Run.
6. After execution output will appear in the Command window .If there is an error then
with an alarm, type of error will appear in red color.
7. Rectify the error if any and go to Debug Menu and select Run.
8.8 LAB RESULT
Thus the ASK modulated and demodulated waves are simulated .

1. Write a matlab program to generate sync function

2. Perform the Binary ASK modulation and demodulation using hardware kit and
study the waveform output

3. Differentiate plot and subplot commands in MATLAB.
9. Binary Frequency Shift Keying

9.1 OBJECTIVE
To simulate Binary Frequency shift keying technique using MATLAB software


1. Define modulation index.

2. Write a matlab program for generating PN sequence.
3. What is MSK and mention its significance.
4. Differentiate coherent and non-coherent FSK.
5. Give the expression for bandwidth of FSK scheme.
9.4 THEORY
Binary Frequency Shift Keying
In binary FSK system, symbol 1 & 0 are distinguished from each other by
transmitting one of the two sinusoidal waves that differ in frequency by a fixed amount.
Si (t) = 2E/Tb cos 2f1t ;
0
0 t Tb
elsewhere
Where i=1, 2 & Eb=Transmitted energy/bit

Transmitted freq= i = (nc+i)/Tb, and n = constant (integer), Tb = bit interval
Symbol 1 is represented by S1 (t)
Symbol 0 is represented by S0 (t)
The set of orthonormal basis function is
i (t) = {2/Tb cos 2f1t ;
0
0 t Tb
elsewhere
Where i = 1, 2.
The two message points ( M =2 ) are defined by signal vectors
S1 = [Eb 0] S2 = [0 Eb]
Block diagram of BFSK Transmitter
Fig 9.1 FSK Transmitter Block Diagram
The i/p binary sequence is represented in its on-off form, with symbol 1
represented by constant amplitude of Eb with & symbol 0 represented by zero
volts. By using inverter in the lower channel, we in effect make sure that when
symbol 1is at the i/p, The two frequency f1& f2 are chosen to be equal integer
multiples of the bit rate 1/Tb
By summing the upper & lower channel outputs, we get BFSK signal.
BFSK Receiver
Fig 9.2 FSK Receiver Block Diagram
The receiver consists of two correlators with common inputs which are supplied
with locally generated coherent reference signals 1(t) and 2 (t).
The correlator outputs are then subtracted one from the other, and the resulting
difference L is compared with a threshold of zero volts. If L >0, the receiver decides
in favour of symbol 1 and if L <0, the receiver decides in favour of symbol 0.
9.5 ALGORITHM
BFSK Modulation
1. Generate two carrier signals (1 (t) = 2/Tb cos 21t and 2 (t) = 2/Tb cos22 t)
3. Convert the base band signal into on-off form.(i.e m(t))
4. Multiply the on-off form data signal m(t) and carrier signal 1 in one channel .
5. Invert the signal m(t) to get m1 (t)
6. Multiply the on-off form data signal m1 (t)and carrier signal 2in another channel
7. Sum the output resultant signals of step 4 and 5.
8. The resultant signal is a FSK signal
9. Plot the carrier, data and FSK signal.
BFSK Demodulation
1. Multiply the received FSK signal with the carrier signal 1 (t) = 2/Tb cos 21t in
one channel and integrate the resultant signal(x1)
2. Multiply the received FSK signal with the carrier signal 2 (t) = 2/Tb cos 2 2t
in
another channel and integrate the resultant signal(x2)

3. Find x=x1-x2.
4. If x is greater than zero then choose 1 and if it is less than 0 choose 0 .
9.6 TEST PROCEDURE


9.7 LAB RESULT
Thus the FSK modulated and demodulated waves are simulated.

1. Determine the bandwidth and baud for an BFSK signal with mark frequency of 49
KHz, a space frequency of 51 KHz, and a bit rate of 2 Kbps.
2. Write a matlab program for finding the sum of series 1+ 2+ 3 ++N
3. Sketch the FSK waveform for the input a) 1010110 b) 1100101
10. Binary Phase Shift Keying

10.1 OBJECTIVE
To simulate Binary Phase shift keying technique using MATLAB software

MATLAB, Computer installed with Windows XP or higher Version.
1) An analog signal carries four bits in each signal element. If 1000 signal elements are
sent per second , find the baud rate and bit rate.
2) What is a correlator?
10.4 MATLAB INTRODUCTION
MATLAB is a programming language and numerical computing environment.

The name MATLAB is an acronym for Matrix Laboratory. As it name suggests it
allows easy manipulation of matrix and vectors. Plotting functions and data is made easy
with MATLAB. It has a good Graphic User Interface and conversion of matlab files to
C/C++ is possible. It has several toolboxes that possess specific functions for specific
applications. For example Image Processing, Neural Networks, CDMA toolboxes are
name a few. An additional package, Simulink, adds graphical multidomain simulation and
Model-Based Design for dynamic and embedded systems. Simulink contains Blocksets
that is analogous to Toolboxes.It was created by Mathworks Incorporation, USA.
MATLAB has become a defacto programming language for Engineers. Writing
MATLAB programs for modulation applications require knowledge on very few
functions and operators. The operators mostly used are arithmetic operators and matrix
operators. To know more type in the command prompt help ops. MATLAB will give a
list in that to know on specific operator say addition type in the command prompt help
plus. MATLAB will give how to use and other relevant information. Commonly used
graphical functions are plot, figure, subplot, title, and mathematical functions are sin and
cos only. The mathematical functions sin and cos are self explanatory. The graphical
function figure will create a new window and then subsequent graphical commands can
be applied. The plot function usually takes two vectors and plot data points according to
given vector data. In this case it will time Vs signal. Subplot function is used when two or
more plots are drawn on the same figure. As title function suggests it helps to write title
of the graph in the figure. For further details type help plot or help subplot in the
command prompt and learn the syntax.
10.5 THEORY
Binary Phase Shift Keying
In a coherent binary PSK system, the pair of signal S1(t) and S2 (t) used to represent
binary symbols 1 & 0 are defined by
S1 (t) = 2Eb/b Cos 2fct
S2 (t) =2Eb/Tb (2fct+) = - 2Eb/Tb Cos 2fct
where 0 t< Tb and
Eb = Transmitted signed energy for bit

The carrier frequency fc =n/Tb for some fixed integer n.
In BPSK, there is only one basis function of unit energy.
b (t) = 2/Tb cos 2fct
0 t< Tb
S1 (t) = Eb 1 (t)
0 t Tb
S2 (t) = Eb 1 (t)
0 t< Tb
The signal space is 1dimensional (N=1) having two message points (M = 2)

Block Diagram of BPSK Transmitter
The input binary symbols are represented in polar form with symbols 1 & 0
represented by constant amplitude levels Eb & -Eb. This binary wave is multiplied by a
sinusoidal carrier in a product modulator. The result in a BSPK signal.
Binary Wave
(Polar form)
Product
Product
Modulator
BPSK signal
1 (t) = 2/Tb cos 2fct

Fig 10.1 PSK Transmitter Block Diagram
BSPK Receiver:
The received BPSK signal is applied to a correlator which is also supplied with a
favour of symbol 0
Fig 10.2 PSK Receiver Block Diagram
The received BPSK signal is applied to a correlator which is also supplied with a
favour of symbol 0
10.6 ALGORITHM
BPSK Modulation
1. Generate the carrier signal (1 (t) = 2/Tb cos 2fct )

3. Convert the base band signal into polar form.
4. Multiply the polar form data signal and carrier signal. The resultant signal is a PSK
signal.
5. Plot the carrier, data and PSK signal.
BPSK Demodulation
1. Multiply the received PSK signal with the carrier signal (1 (t) = 2/Tb cos 2fct )
2. Integrate the resultant signal(x1) .
10.7 TEST PROCEDURE


10.8 LAB RESULT
Thus the FSK modulated and demodulated waves are simulated .

1. Write matlab program to encode the data sequence using

a) RZ
b) NRZ
c) Manchester
d) Differential encoding.
2.Why do we make 180 degree phase shift in PSK and why not 90 or
270?comment on this.
3. What is the function of a decision device.
11. Quadrature Phase Shift Keying

11.1 OBJECTIVE
To simulate Quadrature Phase shift keying technique using MATLAB software

MATLAB, Computer installed with Windows XP or higher Version.

1. What are the types of QPSK?

2. What is the significance of Q-channel and I channel in QPSK modulator?
3. What is the minimum bandwidth requirement of QPSK?
4. Draw the output phase versus time relationship for a QPSK modulator.
5. Compare OQPSK and QPSK.
11.4 THEORY
Quadrature Phase Shift Keying
Phase of the carrier takes on one of four equally spaced values such as /4, 3/4,
/4,7/4.
Si(t) =
2E/ Tb cos {2 ct + (2i 1) /4} , 0 t Tb

0
, elsewhere
Where i = 1,2,3,4, & E= Tx signal energy per symbol

Tb = symbol duration
Each of the possible value of phase corresponds to a pair of bits called dibits.
Thus the gray encoded set of dibits: 10,00,01,11
Si (t) = 2E/ Tb cos [(2i 1)/4] cos (2fct) - 2E/ Tb sin [(2i 1) /4)]
sin (2fct) ,0 t Tb 0 , else where
There are two orthononormal basis functions
1 (t) = 2/ Tb cos 2ct,
0 t Tb
2 (t) = 2/ Tb sin 2ct,
0 t Tb
There are four message points
Input debits
Phase of
QPSK signal
Co-ordinates of message signals

S1
S2
E/2
-E/2
10
/4
00
3/4
-E/2
-E/2
01
5/4
-E/2
+E/2
11
7/4
+E/2
+E/2
Block diagram of QPSK Transmitter
b1(t)
X
+
I/P binary b (t)

Wave
DeMux
QPSK signal
1 (t) = 2/ Tb cos 2ct

+
X
b2 (t)
2 (t) = 2/ Tb sin 2ct
Fig 11.1 QPSK Transmitter Block Diagram
The i/p binary sequence b(t) is represented in polar from with symbols 1 & 0
represented as +E/2 and -E/2 .This binary wave is demultiplexed into two
separate binary waves consisting of odd & even numbered I/P bits denoted by b1
(t) & b2 (t)
b1 (t) & b2(t) are used to modulate a pair of quadrature carrier or orthogonal Basis
function 1 (t) & 2 (t).
The result is two PSK waves .These two binary PSK waves are added to produce
the desired QPSK signal .
QPSK Receiver:
Fig 11.2 QPSK Receiver Block Diagram
QPSK receiver consists of a pair of correlators with common I/P & supplied
with Locally generated Signal 1 (t) & 2 (t).The correlator O/P, x1, & x2 are each
compared with a threshold of zero volts.If x1 > 0, decision is made in favour of
symbol 1 for upper channel and if x1 > 0, decision is made in favour of symbol 0.
Parallely Y x2 >0, decision is made in favour of symbol 1 for lower channel
& if x2 <0, decision is made in favour of symbol 0.
These two channels are combined in a multiplexer to get the original binary
output.
11.5 ALGORITHM
QPSK Modulation
1. Generate two carrier signals (1 (t) = 2/Tb cos 2ct and 2 (t) = 2/Tb cos2ct)

3. Binary wave is divided into odd(b1(t)) and even(b2(t)) numbered input bits.
4. Multiply the odd numbered data signal (b1(t)) and carrier signal 1 in one channel .
5. Multiply the even numbered data signal b2 (t)and carrier signal 2in another channel
6. Sum the output resultant signals of step 4 and 5.
7. The resultant signal is a QPSK signal
8. Plot the carrier, data and QPSK signal.
QPSK Demodulation
1. Multiply the received QPSK signal with the carrier signal 1 (t) = 2/Tb cos 2ct in
one channel and integrate the resultant signal(x1)
2. Multiply the received QPSK signal with the carrier signal 2 (t) =2/Tb cos 2 ct
in
another channel and integrate the resultant signal(x2)

4. If x1 is greater than zero then choose 1 and if it is less than 0 choose 0
5. Multiply the resultant signal from step 3 and 4.
11.6 TEST PROCEDURE


11.7 LAB RESULT
Thus the QPSK modulated and demodulated waves are simulated .

1. Write a matlab program to sample a message signal m(t) and reconstruct it.
2. Identify the error in the mat lab command Sin 3.
3. Draw the constellation diagram of QPSK.

4. Give some applications of QPSK modulation scheme
5. Find the output of the following command.
5^ (2/3) 25/(2*3)
6. What is the relationship between 4 QAM and QPSK?
7. Design a SIMULINK model for QPSK.
12. Differential Phase-shift Keying

12.1 OBJECTIVE
To simulate Differential Phase shift keying technique using MATLAB software


1. What are the applications of DPSK?

2. Give the equation for average probability of symbol error for DPSK.
3. List the operations performed in DPSK transmitter.
12.4 THEORY
Differential phase shift keying

It is the non-coherent version of PSK. It eliminates the need for a coherent reference
signal at the receiver by combining two basic operations at the transmitter:
i) Differential encoding of the input binary wave
ii) Phase shift keying
In effect, to send symbol 0 we phase advance the current signal waveform by 180
, and to send symbol 1 we leave the phase of the current signal waveform unchanged.
Block diagram of DPSK Transmitter:
Input binary
DPSK
Sequence {b k }
signal
(2/Tb) cos(2fct)
{d k }
Logic
network
Amplitudelevel shifter
Product
modulator
DPSK wave
Delay }Tb
{d
k-1
Fig 12.1 DPSK Transmitter Block Diagram
The DPSK transmitter consists of a logic network and a one-bit delay element
interconnected so as to convert an input sequence {bk} into a differentially encoded
sequence {dk}. This sequence is amplitude level shifted and then used to modulate a
carrier wave of frequency fc, thereby producing the desired DPSK wave.
Block Diagram of DPSK Receiver:
Fig 12.2 DPSK Receiver Block Diagram
The received DPSK signal plus noise is passed through a band pass filter centered at the
carrier frequency fc , so as to limit the noise power. The filter output and a delayed
version of it, with the delay equal to the bit duration Tb, are applied to a correlator. The
resulting correlator output is proportional to the cosine of the difference between the
carrier phase angles in the two correlator inputs. The correlator output is finally compared
with a threshold of zero volts, and a decision is thereby made in favor of symbol 1 or
symbol 0. If
the correlator output is positive, the phase difference between the
waveforms received during the pertinent pair of bit intervals lies inside the range /2 to
/2, and the receiver decides in favor of symbol 1.If , on the other hand, the correlator
output is negative, the phase difference lies outside the range /2 to /2, modulo-2,
and the receiver decides in favor of symbol 0.
12.5 ALGORITHM
DPSK Modulation
1. Generate the base band data signal bk.

2. Generate the differentially encoded sequence dk, using the equation
3. d K = d K 1bK d K 1 bK
4. Convert dk into amplitude level shifted sequence.
5. Generate the carrier signal (2/Tb) cos(2fct)
6. Multiply the amplitude level shifted sequence with the carrier signal .
7. The resultant signal is a DPSK signal
8. Plot the carrier, data and DPSK signal.
DPSK Demodulation
1. Multiply the received DPSK signal with the delayed version of it and integrate the
resultant signal (x).
2. If x is greater than zero then choose 1 and if it is less than 0 choose 0 .
12.6 TEST PROCEDURE


12.7 LAB RESULT
Thus the DPSK modulated and demodulated waves are simulated.

1. Write a matlab program for computing linear and circular convolution of two
sequences.
2. Compare DPSK with QPSK modulation scheme.
3. What is differential encoding technique.
Appendix
Data sheet of IC7805
Data sheet of IC74LS191
Data sheet of IC74LF198
Data sheet of IC555
Data sheet of ICCD4051
Data sheet of ICLM565

Lab Manual EC0323 Communication Lab-II Lab

Uploaded by

Copyright:

Available Formats

Lab Manual EC0323 Communication Lab-II Lab

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lab Manual EC0323 Communication Lab-II Lab

Uploaded by

Copyright:

Available Formats

EC0323 COMMUNICATION LAB II

S.R.M. NAGAR, KATTANKULATHUR 603203.

Department of Electronics and Communication Engineering

the modulated and demodulated

the modulated and

Experiment 5: To analyze a FSK modulation system and interpret

the modulated and

Experiment 6: To analyze a PSK modulation system and interpret

the modulated and

d. Graduate will demonstrate the ability to design a system, component or process as

Sub Code : EC0323

Instructional Objective and Program Outcome

c. Graduate will demonstrate the

Experiment 2 : To analyze a PCM system. and

To carry out experiments on

Experiment 3 : To analyze a DPCM system.

To simulate the digital

b. Graduate will demonstrate the

Experiment 7: To identify the various

d. Graduate will demonstrate the

Experiment 1:To demonstrate Time Division

f. Graduate will demonstrate the

Experiment 8: To simulate Binary Amplitude

skills to use modern engineering

shift keying technique using MATLAB

To demonstrate Time Division

TDM Trainer kit

Crystal Frequency 6.4MHz

To analyze a PCM system. and PCM Trainer Kit

Regulated power supply IC 7805 ,IC7812

To analyze a DPCM system and DPCM Trainer Kit

Regulated power supply IC 7805 ,IC7812

To analyze a Delta modulation Delta modulation Trainer Kit

Regulated power supply IC 7805 ,IC7812

To analyze a FSK modulation FSK Trainer Kit

To analyze a PSK modulation PSK Trainer Kit

4 channel analog Multiplexer: IC CD

To identify the various encoding Data formatting Trainer Kit

On-board carrier: Sine waves

To simulate Binary Amplitude shift MATLAB software

To simulate Binary Frequency shift MATLAB software

To simulate Binary Phase shift MATLAB software

To simulate Quadrature Phase shift MATLAB software

To simulate Differential Phase shift MATLAB software

EC0323 Laboratory Policies and Report Format

Laboratory Report Cover Sheet

: Day order 1 AN / Day Order 4 FN

: communication Lab/Computing Lab 10th floor

: Mrs.T.Theresal/ Anantha Venkatesan

Exp 2: Pulse code modulation

Exp 3: Differential Pulse code modulation

3.10 Post lab

Exp 4: Delta modulation and demodulation

Exp 5: Frequency shift keying

Exp 6: Phase shift keying

Exp 7: Data formatting

7.6 Test procedure

Exp 8: Binary Amplitude shift keying

Exp 9: Binary Frequency shift keying

Exp 10: Binary Phase shift keying