Angle Flo XA
Angle Flo XA
Angle Flo XA
Gear-in
1 rpm=ft
Frame
H eight
7"
21AXL35-45
18"
35"
21"
1.079'
27AXL38-45
24"
38"
27"
1.079'
7"
33AX45-45
30"
45"
33"
1.604'
8.5"
43AX60-45
40"
60"
43"
1.604'
8.5"
45AXH63-45
57AXH81-45
42"
54"
63"
81"
45"
57"
2.126'
2.126'
12"
12"
30 Models
21AXL44.14-30
27AXL149.34-30
Gear-in
1 rpm=ft
Frame
H eight
69.7"
43.7"
21.28"
21"
1.079'
7"
24" 49.34"
80.1"
52.7" 27.28"
27"
1.079'
7"
62.92"
98.9"
61.7" 33.28"
33"
1.604'
8.5"
18" 44.14"
33AX62.92-30
30"
43AX71.58-30
40"
71.58" 116.2"
76.7" 43.28"
43"
1.604'
8.5"
45AXH86.27-30
57AXH91.47-30
42"
54"
86.27" 133.6"
91.47" 149.2"
79.6" 45.28"
97.7" 57.28"
45"
57"
2.126'
2.126'
12"
12"
Merge
Application
Note: The above dimensions are for Merge units only and represent the shortest
length for the conveying width. Diverge units are typically longer. Call the factory
for minimum lengths for diverge units. The above models are examples that show
the narrowest and widest conveying widths for each frame height.
Conveyor Belt: 2-ply Black Urethane with very low friction bottom
fabric bottom and vulcanized endless seam. Fire retardent
Belt Drive System: The conveyor belt is driven by its bottom side
contacting a heavy duty lagged drive roll. Contamination of the belt
surface does not effect the conveyor operation. A spring-loaded takeup maintains even belt tension even with changes in loading and
temperature.
Angle Bar: The Angle-Flo uses a polished steel bar on the angle end
of the conveyor. The fixed angle bar ensures even belt tracking and
may be positioned as close as .16 from the adjoining conveyor. The
Angle-Flo is available with angles of 30 and 45 degrees.
End, Take-up, Snub and Return Rolls: The all-steel rolls are
fabricated from 2 (low frame), 2.5 (mid-frame) and 3.5 (high frame)
diameter tubing. The end and take-up rolls have center crowns. The
end roll is normally positioned so the front face of the roller is .25 past
the end of the conveyor frame. It may be adjusted so the roller is .5
from the end of the frame to as much as 1.5 (high frame) extended
past the end of the frame. If the end roll position is adjusted, it is
necessary to readjust the belt tension by repositioning the take-up roll.
Drive Roll: The drive roll is fabricated from 4 (low frame), 6 (midframe) or 8 (high frame) diameter steel tubing. The drive lagging is
molded onto the steel rolls and machined to provided a friction surface.
Roll Shafts: Turned, ground and polished 1045 steel.
Bearings: The drive roll bearings are precision, sealed-for-life, and
fitted in a externally mounted, cast iron flange bearing. The end roll,
take-up and snub rolls have internal bearings.The high frame Angle-Flo
may be ordered with all external bearings as an option.
Return Rolls: The returning belt is supported by cylindrical steel
rollers with precision ball bearings and a 7/16 hex steel shaft.
Sideguards: Standard sideguards are fabricated from 14 gauge
steel. Sideguards over 6 height will have a .75 outward facing top
flange. The distance between the sideguards is 3 wider than the
exposed belt width.
Paint: Angle-Flo conveyors are normally painted with a DTM (direct to
metal) paint in one of five standard colors. Check the Portec Paint
Policy for a wide range of optional colors and paint types.
Diverge
Application
Direction of Travel