Estane 58887

Estane 58887 TPU
Type: Estane 58887 is an 87A aromatic Polyether-Based Thermoplastic Polyurethane (TPU).

Features: Excellent hydrolysis resistance, low temperature performance, clarity and wide processing
window for extrusion.
Uses: Blown and flat die/cast film extrusion, Injection and blow molding; cable jacketing and
profile extrusion.
Physical Properties
Value (Metric)
Unit
Test Method
87 +/- 3
1.12
Shore A
ASTM D-2240
ASTM D-792
7500 (51.7)
500
psi (MPa)
%
ASTM D-412
- 100% Elongation
1000 (6.9)
psi (MPa)
ASTM D-412
- 300% Elongation
Tear Strength:
1800 (12.4)
psi (MPa)
500 (8.9)
lb/in (kg/mm)
ASTM D-624 (die C)
150 (2.7)
0.00141 (40)
lb/in (kg/mm)
oz (mg)
ASTM D-470
ASTM D-3389 (H18, 1000g)
284 (40)
-49 (-45)
F (C)
F (C)
Lubrizol Advanced Materials

Hardness (5 sec)
Specific Gravity
Tensile Strength
Ultimate Elongation
Tensile Stress at:
- Graves
- Trouser
Taber Loss (1000 rev)
Tm (by DSC)
Tg (by DSC)
Prior to testing samples were conditioned at 23C for 48 hours.

Based on extruded sheet (30 mils).
Listed values are typical (average) values and should/cannot be applied for specification purposes.
Supply Form and Standard Packaging

Estane 58887 TPU is supplied in pellet form and packaged in 50 lb bags or 1000 lb boxes.
Material Preparation
Prior to processing, Estane 58887 TPU must be dried at 220F (104C) for 2-4 hours.
It is recommended to dry the material in a desiccant type dryer. Target dew point should be -40C.
Depending on the applied processing technique, the maximum moisture level should be 0.02%.
Processing Conditions
Estane 58887 TPU can be processed on any conventional extruder.
]
The information contained herein is believed to be reliable, but no representations, guarantees or warranties of any kind are made as to its accuracy, suitability for particular applications or the results to be obtained.
The information often is based on laboratory work with small-scale equipment and does not necessarily indicate end product performance or reproducibility. Formulations presented may not have been tested for
stability and should be used only as a suggested starting point. Because of the variations in methods, conditions and equipment used commercially in processing these materials, no warranties or guarantees are
made as to the suitability of the products for the applications disclosed. Full-scale testing and end product performance are the responsibility of the user. Lubrizol Advanced Materials, Inc. shall not be liable for and
the customer assumes all risk and liability for any use or handling of any material beyond Lubrizol Advanced Materials, Inc.s direct control. The SELLER MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Nothing contained herein is to be considered as permission, recommendation nor as an
inducement to practice any patented invention without permission of the patent owner.
Lubrizol Advanced Materials, Inc. / 9911 Brecksville Road, Cleveland, Ohio 44141-3247 / 216.447.5000
2014 The Lubrizol Corporation. All rights reserved. All marks are the property of The Lubrizol Corporation www.lubrizol.com/engineeredpolymers
Estane 58887 Issue date: 10/6/14

Issue nr: 1/1 Owner: LH
Recommended Starting Extrusion Temperature Profile:
F/C
Zone 1
350/177
Zone 2
360/182
Zone 3
370/188
Zone 4
380/193
Adapter (5)
380/193
Die Zone 1 (6)
380/193
Die Zone 2
380/193
Melt Temp. Mid-Range: 375F/191C

Screen Pack Recommendation: 20/40/80
Application Information: High Performance Film & Sheet

Properties
Tensile Set (200% elongation)
Kofler Melt Point
Haze (pressed between glass)
Volume Swell in Water (24h/23C)
Value (Metric)
Unit
Test Method
18
ASTM D-412
302 (150)
1.0
F (C)
%

ASTM D-1003
1.1
ASTM D-471
FDA 177.1680 (dry bulk foods)
Complies*
FDA 177.2600 (wet/fatty foods)
Complies
NSF 61 Status
Listed
*Only for repeat use articles.
Percent of Original Tensile Strength
58887 Immersion in Water at 75C

30 Mil Sheet
120
100
80
60
40
20
0
Weeks of Aging in Water at 75C
For further information refer to Lubrizol Advanced Materials processing guides.
The information contained herein is believed to be reliable, but no representations, guarantees or warranties of any kind are made as to its accuracy, suitability for particular applications or the results to be obtained.
The information often is based on laboratory work with small-scale equipment and does not necessarily indicate end product performance or reproducibility. Formulations presented may not have been tested for
stability and should be used only as a suggested starting point. Because of the variations in methods, conditions and equipment used commercially in processing these materials, no warranties or guarantees are
made as to the suitability of the products for the applications disclosed. Full-scale testing and end product performance are the responsibility of the user. Lubrizol Advanced Materials, Inc. shall not be liable for and
the customer assumes all risk and liability for any use or handling of any material beyond Lubrizol Advanced Materials, Inc.s direct control. The SELLER MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Nothing contained herein is to be considered as permission, recommendation nor as an
inducement to practice any patented invention without permission of the patent owner.
Lubrizol Advanced Materials, Inc. / 9911 Brecksville Road, Cleveland, Ohio 44141-3247 / 216.447.5000
2014 The Lubrizol Corporation. All rights reserved. All marks are the property of The Lubrizol Corporation www.lubrizol.com/engineeredpolymers

Estane 58887

Uploaded by

Copyright:

Available Formats

Estane 58887

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Estane 58887

Uploaded by

Copyright:

Available Formats

Estane 58887 TPU

Type: Estane 58887 is an 87A aromatic Polyether-Based Thermoplastic Polyurethane (TPU).

ASTM D-624 (die C)

Lubrizol Advanced Materials

Prior to testing samples were conditioned at 23C for 48 hours.

Supply Form and Standard Packaging

Estane 58887 Issue date: 10/6/14

Die Zone 1 (6)

Melt Temp. Mid-Range: 375F/191C

Application Information: High Performance Film & Sheet

Lubrizol Advanced Materials

FDA 177.1680 (dry bulk foods)

FDA 177.2600 (wet/fatty foods)

*Only for repeat use articles.

Percent of Original Tensile Strength

58887 Immersion in Water at 75C

Weeks of Aging in Water at 75C

For further information refer to Lubrizol Advanced Materials processing guides.

You might also like