Transforming know-how into reliable energy.

TUMETIC and TUNORMA Oil-Immersed Distribution Transformers

Answers for energy.

TUMETIC distribution transformer with hermetically sealed tank

TUNORMA distribution transformer with conservator

Transforming high standards

into leading solutions
On the last transformation step from the
power station to the consumer, distribution
transformers provide the necessary power
for systems and buildings. Accordingly,
their operation must be reliable, efficient
and, at the same time, silent.

Under the names TUMETIC and

TUNORMA, oil-immersed distribution
transformers from Siemens meet all these
requirements daily again. In thousands
of applications, under extreme climatic
conditions and in the smallest space
in distribution systems as well as in industrial plants. What these transformers
stand for can be summarized in one
single word: quality.

More than 100 years of experience

reliable partnership
The extraordinary quality is based on
more than 100 years of experience of
the pioneer in transformer technology
Siemens. Experience you take advantage
of in all phases of your project:
From technical advice via layout, design,
manufacture, transport, and commissioning up to the Siemens Transformer Life
Management.

Each of our factories is regularly checked for compliance with the quality guidelines by independent bodies.

Oil-immersed distribution transformers from

Siemens: Systematic quality
Oil-immersed distribution transformers
from Siemens are manufactured in
accordance with our quality management
system certified to EN ISO 9001.
Compliance with important standards,
from IEC to VDE, is a matter of course,
just as much as the exclusive use
of high-quality materials. Qualified
employees implement the demanding
standards in daily practice.
So, quality is the logical result of a
universal philosophy.

Checking means security

in production and testing

State-of-the-art technology
tested and documented

Every transformer consists of a large

number of individual components which
must interact smoothly in operation.

Besides the routine tests for all transformers,

we also take over the type and special
tests on request.

The high quality of Siemens transformers

is therefore guaranteed by adhering to
strict quality standards in production
all of them compiled in a quality assurance
manual, which is also at the disposal of
our customers.

For Siemens, however, quality assurance

is even more. We support you in every
respect as regards equipment monitoring
and operation. And due to the fact that
further improvement of the transformer
technology is accelerated by the knowledge from daily operation, we offer you
a continuous exchange of experience
for our common advantage.

Each manufacturing step is accompanied

by quality checks partly as a self-check
with the associated evidence, partly by
instructed quality experts. Final testing or
acceptance tests are exclusively performed
in the testing laboratory. And if you like
to join the test of your transformer:
Welcome!

even with regard to environmental aspects

The protection of our environment and
economic use of resources is more and
more in the focus worldwide. This applies
both to nature and growing cities, where
power supply and industrial plants are
often installed directly close to buildings,
households and people. All Siemens
factories work in accordance with an
environmental management system
certified to EN ISO 14001.

With Siemens transformers you are also

on the safe side regarding environmental
protection and sustainability. For especially
high demands we offer special designs
as the following examples show:
 Environmental protection by alternative
coolants and transformer fluids: Here,
mineral oil is the most common, but
not the only option. Ester and silicone
are to be recommended for special
requirements as regards fire safety and
ecology (see also page 8 transformer
fluid)
 E
 verything is all right in water protection
areas by designing the tank as a
double tank
 No problems with radiation:
Siemens offers low-radiation transformers
complying with the strict Swiss standards
and conforming to the future European
standards already today.

Oil-immersed distribution transformers

from Siemens: Exactly matching your demand
The decisive factors for the layout of a
distribution transformer are just your
requirements, which we use for adjusting
the different parameters from the rated
power to the vector group, from the
coolant to the taps.
Of course the most different combinations
are possible, which results in custom-made
distribution transformers for almost every
field and place of application.

Tailored to the requirements of

practice an example:
An urban industrial plant requires an
especially ecological transformer.
The Siemens solution fully meets this
requirement from biodegradeable
transformer fluid up to extreme reduction
in radiation. The sound level is at the
limit of audibility, and the loss values
are really acceptable with no-load
losses 30% below the lowest loss range
C which is presently defined in the
European standards.

Custom work in macrocosm

and in microcosm
Low losses, low noise:
The iron core

Systematically safe:
The winding

Whether in design, manufacturing

methods or materials the cores of
Siemens transformers represent the
latest state of technology. The siliconalloyed electric sheet steel used is
grain-oriented, cold-rolled and insulated
on both sides, guaranteeing low losses
and noise and these values are even
improved by laser treatment.

The winding as the centerpiece of the

transformer must be especially protected
both against high electrical stress due
to external overvoltages and against
mechanical overloads by short circuits.

Numerically controlled cutting machines

provide for careful treatment in the cutting
process in order to avoid mechanical
tension in the core and thus unwanted
properties right from the beginning.
Standard use of step-lap cutting additionally
minimizes losses and noise.

Siemens transformers are systematically

designed to meet these requirements.
The windings are made of copper or
aluminum. Low-voltage windings are
made of strip or flat wire, and the highvoltage windings are manufactured from
round or profile wire. The use of insulating
paper that is partially coated with epoxy
resin (diamond-dotted paper) bonds the
winding into a compact block while drying
and increases the short-circuit capacity
additionally.

The layer insulation is adapted to the

occurring alternating voltage strain in
daily operation. Large-scale oil channels
are provided in order to secure sufficient
cooling of the windings and to avoid
hot spots. All leads are short-circuit and
surge-proof, contributing to the high
reliability of the transformer with an
above-average service life.

Tightness decides:
The tank
Whether during transport or operation
the tank must be absolutely tight under
mechanical stress. Preconditions to achieve
this are constructional experience, the
most modern calculation methods and
high-quality welding work.
Special attention is paid to corrosion
protection. Pretreatment of the surface
by sandblasting contributes to corrosion
protection, just like multicoating with
preset drying times for each layer. On
request, hot-dip galvanization provides
for even better protection.

The tank must dissipate the entire heat loss

of the transformer into the ambient air.
This makes the volume of the transformer
fluid change. In hermetically sealed transformers, the corrugated walls absorb the
change in volume. In the case of expansion
tank transformers, the conservator compensates this change.
The sheet-steel lids of Siemens transformers
are bolted together with the tank or
welded on request. In any case the steel
thickness and the bracing is dimensioned
in such a way that the lid withstands the
stress of transport and operation.

Oil-immersed 630-kVA distribution transformer TUMETIC:

View into the inside

Core and windings

Both are held together by a pressed
structure and bolted together with the
tank lid. The complete unit can be lifted
out of the tank.
Core
High-quality electric sheet steel, most
modern core design and optimized
lamination provide for low-loss and
noise-optimized operation.
Windings
Construction and materials guarantee
a long service life.
Tap changer
Used to adjust the ratio to the local
voltage conditions. It can be adjusted
from outside in de-energized condition.

Low-voltage bushings

High-voltage bushings

Tank
The TUMETIC design shown here is
hermetically sealed. Elastic corrugated
walls take up the volume changes of the
transformer fluid.

11

Truck
Plain transport wheels can be aligned for
longitudinal or transversal movement.

10 Conservator
In the TUNORMA type, it is equipped with
an oil level indicator and a filling socket.

11 Corrosion protection
The surface gets a multicoating in the
standard color cement gray (RAL 7033).
Special colors or galvanization are possible.
9

Mineral oil, which complies with

the specifications of the international
standards for insulating oils, IEC
publication 60296 for distribution
transformers without special requirements.
Silicone oil, which is self-extinguishing
in case of fire. Due to its high fire point
above 300 C it has been classified as a
K-liquid according to IEC 61100.
Ester, which is nonhazardous to water
and has a very good biodegradability.
Additionally, ester offers high fire
safety due to its high fire point above
300 C, and has also been classified as
a K-liquid according to IEC 61100.

Thermometer bag
Important accessory for temperature
monitoring.

From oil to ester:

The transformer fluid
Insulating and cooling these tasks
represent high requirements for the
transformer fluid: It must be insensitive
to high temperatures, to the influence
of air oxygen and catalysts; furthermore
it has to be resistant to aging and non
corrosive. Siemens uses the adequate
fluid for each customer requirement
and application:

TUMETIC distribution transformers

(hermetically sealed tank)

TUNORMA distribution transformers

(with conservator)

38

11

10

3 8
10

2N2U2V2W
H1

1U 1V 1W

1U 1V 1W

1
2
3
4

Oil level indicator

Oil drain valve
Thermometer pocket
Buchholz relay (on order)

2N 2U2V 2W

H1

B1

A1

5
6
7
8

Dehydrating breather (on order)

Adjustment facility for tap changer
Rating plate (movable)
Earthing terminal

9
6

8
E

B1

A1

9 Pulling lug, 30 mm
10 Lashing lug
11 Filling tube

Perfectly prepared for any task

whether standard or special
TUMETIC and TUNORMA two transformer
types, many applications. The standard
design already covers a wide range of
requirements, but as we know from long
years of experience, special applications
ask for special solutions. That is why
Siemens offers a wide variety of useful
additional solutions, assembly appliances
and devices. Here are some examples:


Safe-to-touch outside-cone and

inside-cone plug-in bushings on the
high-voltage side instead of porcelain
bushings.
 Transformer connection terminals on
the low-voltage side with or without
covers.
Bar bushings on the low-voltage side
with or without covers.
 Air-filled cable connection boxes for
special protection requirements.
 All relevant protection and monitoring
devices for distribution transformers.

Published by and copyright 2009:

Siemens AG
Energy Sector
Freyeslebenstr. 1
91058 Erlangen, Germany
Transformatorenwerk Weiz
Elingasse 3
8160 Weiz
Austria
Tel.: +43 51707-71 328
Fax: +43 51707-55 447
Siemens Transzformtor Kft.
II. Rkczi Ferenc t 189
Budapest 1214
Hungary
Tel.: +36 (1) 278 5300
Fax: +36 (1) 278 5335
Siemens Fbrica de Transformadores
Apartado 501
Sabugo 2715 981
Portugal
Tel.: +351 21 9627309
Fax: +351 21 9627293
For more information, contact our
Customer Support Center.
Phone: +49 180/524 70 00
Fax: +49 180/524 24 71
(Charges depending on provider)
e-mail: [email protected]
Power Transmission Division
Order No. E50001-G640-A142-X-4A00
Printed in Germany
Dispo 19200, c4bs No. 7481
GB 090579 470887 WS 11092.
Printed on elementary chlorine-free bleached paper.
All rights reserved.
Trademarks mentioned in this document are
the property of Siemens AG, its affiliates, or their
respective owners.
Subject to change without prior notice.
The information in this document contains general
descriptions of the technical options available, which
may not apply in all cases. The required technical
options should therefore be specified in the contract.

www.siemens.com/energy