Datasheet SHARP

LQ070T3GR01
Color TFT LCD Module

(Model Number: LQ070T3GR01)
http://www.DataSheet4U.net/
Specifications
Spec No.: LCY-00056A

Dated: May 31. 2002
datasheet pdf - http://www.DataSheet4U.net/
PREPARED BY:
DATE
APPROVED BY:
DATE
SPEC No.
LCY-00056A
FILE No.
ISSUE:
MAY.23. 2000
PAGE : 19 pages
LIQUID CRYSTAL DISPLAY GROUP

SHARP CORPORATION
SPECIFICATION
APPLICABLE GROUP
LIQUID CRYSTAL DISPLAY
GROUP
DEVICE SPECIFICATION FOR
TFT - LCD module

MODEL No. LQ070T3GR01
LQ038Q5DRQ1
CUSTOMER'S APPROVA
DATE
PRESENTED
BY
BY
S.YASUDA
Department General manager
Development Engineering Dept.2
TFT Division.1
TFT LIQUID CRYSTAL DISPLAY GROUP
SHARP CORPORATION
RECORDS OF REVISION
R

NO.
2000.02.15
2000.11.01
PAGE
SUMMARY
NOTE
1st Issue
4.5mArms 6.5mArms
Correction
LCY000561
NOTICE
This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the
copyright laws, no part of this publication may be reproduced or transmitted in any form or by any
means, electronic or mechanical for any purpose, in whole or in part, without the express written
permission of SHARP. Express written permission is also required before any use of this publication
may be made by a third party.
The application circuit examples in this publication are provided to explain the representative
applications of SHARP's devices and are not intended to guarantee any circuit design or permit any
industrial property right or other rights to be executed. SHARP takes no responsibility for any
problems related to any industrial property right or a third party resulting from the use of SHARP's
devices, except for those resulting directly from device manufacturing processes.
In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any
defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc.
Contact SHARP in order to obtain the latest device specification sheets before using any SHARP's
device.
SHARP reserves the right to make changes in the specifications, characteristics, data, materials,
structures and other contents described herein at any time without notice in order to improve design or
reliability. Contact SHARP in order to obtain the latest specification sheets before using any SHARP's
device. Manufacturing locations are also subject to change without notice.
Observe the following points when using any device in this publication. SHARP takes no responsibility
for damage caused by improper use of the devices.
The devices in this publication are designed for use in general electronic equipment designs, such as:
Personal computers
Office automation
Test and measurement equipment

Audio visual and multimedia equipment
Telecommunication equipment
Industrial control
Consumer electronics
The appropriate design measures should be taken to ensure reliability and safety when SHARP's
devices are used for equipment such as:
Transportation control and safety equipment(i.e.,aircraft,trains,automobiles,etc.)
Traffic signals
Gas leakage sensor breakers
Alarm equipment
Various safety devices etc.
SHARP's devices shall not be used for equipment that requires extremely high level of reliability, such
as:
Military and space applications
Nuclear power control equipment
Medical equipment for life support
Contact a SHARP representative, in advance, when intending to use SHARP's devices for any "specific"
applications other than those recommended by SHARP.
Contact and consult with a SHARP representative if there are any questions about the contents of this
publication.
LCY000562
(1) Summary
This module utilizes amorphous silicon thin film transistors and a 16:9 aspect ratio. A 7.0 active matrix
liquid crystal display allows full color to be displayed.
An outline of the module is given in Table 1.
(2) Features
Utilizes a panel with a 16:9 aspect ratio, which makes the module suitable for use in wide-screen
systems.
The 7.0 screen produces a high resolution image that is composed of 112,320 pixel elements in a stripe
arrangement.
Wide viewing field angle technology is employed. (The most suitable viewing angle is in the 6 o'clock
direction.)
By adopting an active matrix drive, a picture with high contrast is realized.
Reflection due to external light is minimized through the use of a low reflection, black matrix and an
antiglare low reflection (AGLR) plate.
A thin, light and compact module is accomplished through the use of COG mounting technology.
By adopting a high aperture panel, high transmittance color filter and high transmission polarizing
plates, transmittance ratio is realized.
(3) Structure and External Shape
External measurements for the module are given in Fig. 1, and the structure of the module is shown in
Fig. 2.
The module is composed of the TFT-LCD panel, drivers, frame, backlight, sealed front case, and sealed
back case.
(4)Mechanical specifications
table 1
Parameter
Display format
Specifications
Units
Remarks
336,960
pixels
dots
1440(W)234(H)
Active area
mm
154.1W87.0H
Screen size (Diagonal)
cm
17.7 [7.0]
Dot pitch
mm
0.107W0.372H
Pixel configuration
R,G,B Stripe configuration
Outline dimension
mm
Note1-1
166.0(W)102.0(H)7.6(D)
Mass
205 (max)
Note1-1
Typical values are given. For detailed measurements and tolerances,
please refer to Fig. 1.
LCY000563
(5)Input / Output terminal 5-1)TFT-LCD panel driving part
table 2
Pin No.
Symbol i/o
Description
1
Power supply for gate driver(High level).

2
Open
Open
MODE
(SH
Remarks
Control signal for gate driver.
Note 2-1
MODE
Control signal for gate driver.
Note 2-1
Switching signal of scanning direction for gate driver.
Note 2-2
Start signal for gate driver.
Clock signal for gate driver.
Power supply for logic circuit in gate driver.(High level)
10
Open
11
Open
12
13
Open
14
Open
15
Power supply for gate driver (Low level)
16
17
18
Common electrode driving signal.

Ground
Clock signal for source driver.
19
20
5
6
Power supply for logic circuit in gate driver (Low level).
/o Start signal for source driver.
Control signal for source driver.
Note 2-3
Power save signal.
Note 2-4
Switching signal of scanning direction for source driver.
21
22
23
24
Ground
25
Color video signal (Blue)
26
Color video signal (Green)
27
Color video signal (Red)
28
Ground
29
Power supply for source driver (High level)
30
31
32
Note 2-2
o/i Start signal for source driver.
Note 2-1
Refer to 7-7)
Note 2-2
Refer to 7-4)
Note 2-3
Refer to 7-5)
Note 2.4
Please usually use this terminal in high voltage.
5-2) Backlight fluorescent tube driving part
terminal
Note3-1
Symbol i/o
Function
Remarks
Input terminalhigh voltage side
Input terminallow voltage side

Note3-1
Connect the low voltage side of the DC/AC inverter used to drive the
fluorescent tube to GND of the inverter circuit.
LCY000564
(6)Absolute maximum ratings
table 3
Parameter
Positive power supply voltage
Power
TFT driving High level
supply for circuit
Low level
gate driver Logic
High level
circuit
Low level
Unit
Note
Note 4-1,2
Note 4-1,2,3
Note 4-4
Symbol
-0.3
+6.0
-0.3
+33.0
VGH-33.0 VGH+0.3
VSS-0.3
VSS+7.0
VGH-33.0 VGH+0.3
+0.3
+35
VSSVGL
-0.3
VSH+0.3
Analog input signals [terminal 4-1]
-0.3
VSH+0.3
Digital input signals [terminal 4-2]
-4
+6
Common electrode driving signal
-25
70
Storage temperature
stg.
0
70
Operating temperature panel surface
opr1
0
55
Operating temperature
opr2
Ambient temperature
[terminal 4-1]
[terminal 4-2]
Note 4-1
Note 4-2
This rating applies to all parts of the module and should not be exceeded.
Maximum wet-bulb temperature is 58. Condensation of dew must be
avoided as electrical current leaks will occur, causing a degradation of
performance specifications.
Note 4-3
The operating temperature only guarantees operation of the circuit.

For contrast, speed response, and other factors related to display quality,
determine operating temperature using the formula Ta=25
Ambient temperature when the backlight is lit (reference value).
Note 4-4
LCY000565
(7)Electrical characteristics
7-1)Recommended operating conditions
A)TFT-LCD panel driving section
table 4
Parameter
Power supply for source driver
Power supply for TFT
High level
gate driver
driving Low
AC
circuit level
DC
Logic
High level
circuit
Low level
Analog input signal
AC component
Terminal
DC component
Digital input signal
High level
Terminal
Low level
Digital input current
High level
Terminal
Low level
Unit
Remarks
Symbol
VSH
+4.8
+5.0
+5.5
V Note5-1
VGH
+12.5
+13.0
+13.5
V
Vp-p
VGLAC
0.5
3.9
5.0
VGLDC
-9.5
-10.0
-10.5
V
VCC
VSS+VSH VSS VSS+VSH
V
+0.2
0.1
VSH
V
VSS
18.0
17.0
16.0
V Note5-2
VIAC
2.0
2.0
VIDC
VSM-0.1 VSM VSM+0.1
V Note5-3
VSH
V
VIDSH
VSH-1.0
1.0
V
VIDSL
0
60.0
IIDSH
A VIDSH=VSH
IIDSL
60.0
A VIDSL=0V
2.4
A Only HRV
VSH
V
Digital input voltage
High level
VIDGH VSH-1.0
Terminal
1.0
V
Low level
VIDGL
0
3.0
Digital input current
High level
IIDGH
A VIDGH=VSH
Terminal3
3.0
Low level
IIDGL
A VIDGL=0V
Vp-p
Common electrode
AC component
VCAC
0.5
3.9
5.0
driving signal
DC component
VCDC
+0.5
+2.0
+3.5
V Note 5-1,5-4
Cautionary Matter: When applying or disconnecting power, please be sure that such action is
simultaneously carried out for all power supplies. In addition, apply input signals only after power has
been turned on.
ON VSHVSSVCCVGLVGH
OFF VGHVGLVCCVSSVSH
[terminal 2-1]
[terminal 2-2]
[terminal 2-3]
Note5-1
Any change in voltage after adjusting VCDC should be less than 0.1 V.
Note5-2
Positive and negative amplitudes should be equal. When the AC input voltage
is , FRPV and T are in phase. When the AC input voltage is ,
FRPV and T are 180out of phase. The MIN value produces a white display,
and the MAX value produces a black display.
Note5-3
VSM=VSH/2.
Any change in voltage after adjusting VCDC should be less than 0.1 V.
Note5-4
To obtain the maximum value of contrast, each module must be adjusted to an
optimum voltage.
B)Backlight driving section
table 5
Unit
Remarks
Parameter
Symbol
325
375
425
Vrms 6.5mArms
lamp voltage
3.0
6.5
7.0
mArms ordinary state
lamp current
100
kHz
45
lamp frequency
850
Vrms Ta=+25
kick-off voltage
1000
Vrms Ta=0
Inverter Harison Electric co. Ltd.

LCY000566
7-2)Electrical characteristics
table VSH=5.0V,VGH=13.0V,VCC=-10.9V,VSS=-16.0V,VGLDC=-10.0V,VGLAC=3.9V,GND=0V,Ta=25
Parameter
Operating Clock frequency
High level clock width
S Low level clock width
O Clock rise time
U Clock fall time
R Data set up time
C Data hold time
E
High level pulse width
Pulse rise time
Pulse fall time
G
A
T
E
Operating Clock frequency

Minimum clock pulse with
Clock rise time
Clock fall time
Data set up time
Data hold time
Mode set up time
Pulse rise time
Pulse fall time
Symbol
fCLD
tWHC
tWLC
trD
tfD
tSUD
tHD
tWHD1
trP
tfP
MIN
80.0
80.0
30.0
30.0
0.4
fCLS
tWHS
trCL
tfCL
tSUS
tHS
tSUM
trS
tfS
0.5
100.0
300.0
300.0
-
TYP
-
MAX
5.0
20.0
20.0
-
Unit
MHz
ns
ns
ns
ns
ns
ns
s
20
20
ns
ns
16.5
100.0
100.0
100
100
kHz
s
Remarks
CLD
SPIO,SPOI
CLS
ns
ns
ns
ns
ns
ns
ns
CLS
SPS
CLSMODE2
SPS
7-3)Input signal timing chart

Refer FIG.4
7-4)Signal for reverse scanning

table 7
Mode
Normal mode
Hi
Lo
Right/Left reverse mode
Lo
Lo
Up/Down reverse mode
Hi
Hi
Right/Left & Up/Down reverse mode
Lo
Hi
caution Lo=GND , Hi=VSH
7-5)CRT terminal
This is control signal of switching sample holder circuit. Please set the high or low level synchronizing
with SPD signal during the period each horizontal line.
High level = VSH, Low level = GND

7-6) Current dissipations
table8
Parameter
Current for source driver
Current for gate driver
Lamp power consumption
Hi
Hi
Lo
Logic
Symbol
ISH
IGH
IGL
ICC
ISS
WL
Conditions
VSH=+5.0V
VGH=+13.0V
VGLDC=-10.0V
VCC=-10.9V
VSS=-16.0V
Normal driving
45
0.1
0.1
0.02
0.2
2.4
60
1.0
1.0
1.0
1.0
-
Unit
mA
mA
mA
mA
mA
W
LCY000567
Condition : CLS=15.73kHz, the SPS=60Hz, the SPD=15.73kHz and the CLD=3.99MHz
In case of using exclusive control-IC (LZ9GJ24) and inputting standard NTSC
signal.
7-7)Signal for control of gate driver
table 9
MODE
MODE
Outputting mode
Normal mode1 line writing
Out of use
No outputting
Note)
Lo=GND
2 line same time writing mode
, Hi=VSH
(8)Optical characteristics
Table 10
Ta=25
Parameter
Symbol
Condition
Min
Typ
60
65
Viewing angle range 11
35
40
12
CR
60
65
2
Contrast ratio
Crmax
Optimal
60
30
Response Rise
r
50
time
Fall
d
Luminance
Y
IL=6.5mArms
300
400
White chromaticity
x
IL=6.5mArms
0.263
0.313
y
IL=6.5mArms
0.279
0.329
lamp
life +25
Continuation
10,000
time
intermission
2,000
0
DC/AC inverter for external connection shown in following.
Harison Co.: HIU288
Please refer to Note6-5 for luminance.
Max
60
100
0.363
0.379
-
Unit
Remarks
(degree) Note 6-1,2,3
(degree)
(degree)
Note 6-2,3
ms
Note 6-2,4
ms
cd/m2
Note 6-5
Note 6-5
hour
Note 6-6
time
Note 6-7
LCY000568
measuring after 30minutes.
Photodetector(including luminosity facter)
LCD panel
TFT-LCD Module
DC/AC inverter driving frequency49kHz
Center
mesuring method for optical characteristics
Note 6-1 Viewing angle range is defined as follows.
Normal line
2
11
12
2
6 oclock direction
Note 6-2
definition for viewing angle

Applied voltage condition:
(1) VCDC is adjusted so as to attain maximum contrast ratio.
(2) Input 1.90V at VIAC.
When VI50= transmission is 50% at Voltage-Transmission curve,
Black level : Vi502.5V, White level :Vi50 + 1.5V
LCY000569
Note 6-3
Contrast ratio is defined as follows:

Photodetector output with LCD being "white"
Contrast ratio(CR)=
Photodetechor output with LCD being "black"
Note 6-4
Response time is obtained by measuring the transition time of photodetector

output, when input signals are applied so as to make the area "black" to and
from "white".
White
Black
White
t
u
p
t
u
o
r
e
t
c
e
t
e
d
o
t
o
h
P
)
t
i
n
u
y
r
a
r
t
i
b
r
a
(
Time
Note 6-5 Measured on the center area of the panel at a viewing cone 1 by
TOPCON luminance meter BM-7.(After 30 minutes operation)
DC/AC inverter driving frequency:70kHz
( Including a rise in luminance because of rising frequency.)
Note 6-6 Lamp life time is defined as the time when either or occurs in the continuous
operation under the condition of lamp current IL=3.0~6.5mArms(7.0mArms: Max)
and PWM dimming 100%~5% (Ta=25)
Brightness not to become under 50% of the original value.
Note 6-7 The intermittent cycles is defined as a time when brightness not to become under 50%
of the original value under the condition of following cycle.
Ambient temperature: 0
HIGH(7.0mArms: Max)
OFF
5min
5min
5min
5min
LCY0005610
(9)Mechanical characteristics
9-1) External appearance
Do not exist extreme defects. (See Fig. 1)
9-2) Panel toughness
The panel shall not be broken, when 19N is pressed on the center of the panel by a
smooth sphere having 15 mm diameter.
Caution: In spite of very soft toughness, if, in the long-term, add pressure on the
active area, it is possible to occur the functional damage.
9-3) I/O connector performance
A)Input/output connectors for the operation of LCD module
1)Applicable FPC
: FCI:SFV32R-1ST
2)FPC flexibility : I. Slit on the film cover lay
If it had been tested bending under radius 0.6 mmR and bending angle 90
degrees condition, the FPC should not be cut at 30 times in or less.
II. Slit on the film cover lay coat part of one side printing
If it had been tested bending under radius nothingness and bending angle
180degrees, the FPC should not be cut.
(It should be bend by hand and only at once).
B)I/O connector of backlight driving circuit JST
Symbol
Used Connector
Corresponding connector
CN1
BHR-02VS-1
SM02B-BHSS-1-TB (assembled on PWB)
(10) Display quality

The display quality of the color TFT-LCD module shall be in compliance with the Incoming
Inspection Standard.
(11) Handling instructions
11-1) Mounting of module
The TFT-LCD module is sure to fix the module on the same plane, taking care not to warp
or twist the module.
Dont reach the pressure of touch-switches of the set side to a module directly, because images
may be disturbed.
Please power off the module when you connect the input/output connector.
Please connect the metallic shielding cases of the module and the ground pattern of the inverter
circuit surely. If that connection is not perfect, there may be a possibility that the following
problems happen.
a). The noise from the backlight unit will increase.
b). The output from inverter circuit will be unstable. Then, there may be a possibility that some
problems happen.
c). In some cases, a part of module will heat.
11-2) Precautions in mounting

Polarizer which is made of soft material and susceptible to flaw must be handled carefully.
Protective film (Laminator) is applied on the surface to protect it against scratches and dirts.
It is recommended to peel off the laminator immediately before the use, taking care of static
electricity.
Precautions in peeling off the laminator.
A) Working environment
When the laminator is peeled off, static electricity may cause dust to stick to the polarizer
surface.
To avoid this, the following working environment is desirable.
a) Floor: Conductive treatment of 1M or more on the tile.
( conductive mat or conductive paint on the tile)
b) Clean room free form dust and with an adhensive mat on the doorway
c) Advisable humidity: 50%70%
Advisable temperature: 1527
LCY0005611
d) Workers shall wear conductive shoes, conductive work clothes, conductive
gloves and an earth band.
B) Working procedures
a) Direct the wind of discharging blower somewhat downward to ensure that
module is blown sufficiently. Keep the distance between module and
discharging blower within 20 cm.
b) Attach adhensive tape to the laminator part near discharging blower
so as to protect polarizer against flaw.
c) Peel off laminator, pulling adhesive tape slowly to your side taking 5
or more second.
d) On peeling off the laminator, pass the module to the next work process
to prevent the module to get dust.
D ire ction o f w in d of b low e r
d isch argin g blow er
le ss th an 20cm
m od u le
A d h e siv e ta p e
back ligh t cable
e) Method of removing dust from polarizer

Blow off dust with N2 blower for which static electricity preventive measure has been
taken.
Ionized air gun (Hugle Electronics Co.) is recommended.
Since polarizer is vulnerable, wiping should be avoided.
But when the panel has stain or grease, we recommend to use adhesive tape
to softly remove them from the panel.
When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft
dry cloth. For stubborn dirts, wipe the part, breathing on it.
Wipe off water drops or finger grease immediately. Long contact with water may cause
discoloration or spots.
TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on
hard surface. Handle with care.
Since CMOS LSI is used in this module, take care of static electricity and earth your body when
handling.
11-3) Precautions in adjusting module

Adjusting volumes on the rear face of the module have been set optimally before shipment.
Therefore, do not change any adjusted values. If adjusted values are changed,
the specifications described here may not be satisfied.
11-4) Caution of product design
The LCD module shall be protected against water salt-water by the waterproof cover.
Please take measures to interferential radiation from module, to do not interfere
surrounding appliances.
11-5) Others
Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours;
liquid crystal is deteriorated by ultraviolet rays.
Store the module at a temperature near the room temperature. At lower than the rated
storage
temperature, liquid crystal solidifies, causing the panel to be damaged. At higher than the rated
storage temperature, liquid crystal turns into isotropic liquid and may not recover.
LCY0005612
The voltage of beginning electric discharge may over the normal voltage because of leakage
current from approach conductor by to draw lump read lead line around.
If LCD panel breaks, there may be a possibility that the liquid crystal escapes from the panel.
Since the liquid crystal is injurious, do not put it into the eyes or mouth. When liquid crystal
sticks to hands, feet or clothes, wash it out immediately with soap.
Observe all other precautionary requirements in handling general electronic components.
Please adjust the voltage of common electrode as material of attachment by 1 module.
(12)
Shipping form
12)Packing form (Refer Fig.5)

12Carton keeping conditions
The cartons can be piled up maximum 10 layers.
Environments
Temperature
Humidity
or lessat
Atmosphere
Harmful gas such as acid or alkaline that bites electronic
No dew condensation at low temperature and high humidity.

components and/or wires, must not be detected.
Periods
Opening of the package
About months
: In order to prevent the LCD module from breakdown by
electrostatic charges, please control the humidity over 50%RH
and open the package taking sufficient countermeasures against
electrostatic charges, such as earth, etc..
13Reliability test
table 13
Remark) Temperature condition is based on operating temperature conditions No. (6) table5-1.
No.
Test items
Test condition
High temperature strong test Ta = +75
240h
Low temperature strong test Ta = -25
240h
High temperature and high Ta = +40, 90%RH
240h
humidity operation test
Hi
temperature
operating Tp = +70
240h
test
Low temperature operating Ta = 0
240h
test
Electro static discharge test
Shock test
200V200p0 1 time for each terminals

980/s26ms
direction
Vibration test
3 times for each
JIS C0041, A-7 Condition C
Frequency range :1055Hz

Stroke
Cycle
: 1.5mm
1 minutes
Each direction(X,Y, Z) 2 hours

cautionJIS C0040, A-10 condition A
Heat shook test
-25 +70 / 5 cycles

(0.5)
(0.5)
LCY0005613
NoteTa = Ambient temperature, Tp = Panel temperature

Check itemsIn the standard condition, there shall be no practical problems that may affect
the display function.
It is the goal specification with a mass production article, and there also is an item which you are not
satisfied of this condition in a prototype level.
caution direction are shown as follow
14Indication of lot number label

Attached location of the label
: See Fig. 1
Indicated contents of the label

Model number
Contents of lot number
Lot number
: 1st
Production year 20000
: 2nd
Production month 1,2,3,9,X,Y,Z
: 3rd7th Serial numbers 00001

: 8th
Revision symbols A,B,C
LCY0005614
Fig1. Out line Dimension for 7TFT
LCY0005615
Fig. 2 Structure of the TFT-LCD module
LCY00012-16
R1101
10
R1103
R1102
9.1K
10k
R1104
D1101
5.1B
5.1K
C1903
C1902
0.22u
C1922
56 55
470p
47k
C1920
CLS
SPS
VR
MOD1
N.C
VCC
TCLK
GND
LOWI
MON_66
N.C
MON_67
N.C
BLKI
VIN
TST1
HSY
TEST
FRPT
TST2
SYNI
RESV
FRPV
RESH
N.C
GND
VCC
0.1u
54
MON_54
CVOP
CLD
GND
GND
LZ9GH22
N.C
NTPC
0.1u
1.0u
C1905
C2010
VCC
R1604
15uH
270
L1601
C1603
C1602
1000p
C1601
33p
33p
IC1301
1M
GND
OSCO
HRVC
VRVC
CLKC
R1406
MON_41
N.C
D1402
MA152K
C1402
R1401
R1407
C2005
C2004
C2001
1.0u
C1007
C2003
C2002
1.0u
1M
560p
4.7k
R1402
CTR
68K
R1404 NJM2107F
220p
1000p
Q1301
2.7uH
10k
C1403
0.1u
L1301
MA335
VR1301
10k
R1315
2.4K
2SC2411K
100p
C1302
C1304
10K
R1309
0.1u
C1306
R1305
0.1u
3.3k
330
390p
R1304
R1906
C1005
0.1u
L1001
1000p
C2009
1000p
R1908
560
R1910
560
R1905
R1964
22k
560
560 560
22k
C1906
0.1u
R1911 R1914
R1918
R1963
27k
R1965
27k
560
open R1912
240
560
560 R1907560
R1909
R1962
R1913
R1973
L1002
10uH
C2008
1000p
0.1u
560
2.2uH
0.1u
0.1u
C1004
0
0.1u
C1001
C1907
R2002
C1923
C2012
100p
100
C1910
0.1u
open
100
100
10uF/ 25V
C1913
C1911
0.1u
C1909
0.1u
R/L
SPS
CLS
VSS
COM
CLD
SPIO
CTR
OPEN
OPEN
HR
OPEN
OPEN
MOD2
VGL
0.1u
C1915
VA1
GND
OPEN
VA2
VB2
VC2
GND
SPOI
VA3
VB3
VC3
10u
VB1
R1917
VC1
R1916
VSH
23
22
21
20
19
18
24
VCS
MDN
MDW
MDS
CLK
TST
PWM
16
15
14
13
12
11
CLKC 17
VRV
HRV
VSY
NTPC
COM
VSS
10
VSH
GND
VG
VR
VB
FRPV
VGH
SYNI
FRPT
HSY
CN1
OPEN
R1915
10u
C1914
CN2
0.1u
VGH
R1904
560
D1301
VCC
560
R1902
R1306
37
C1301
C1303
VCC
R1929R1928
100
0.1u
24K
47k
36
R1302
R1303
C1401
MOD1
R2001
C1006
R1903
560
0.1u
C2007
0.1u
0.1u
100p
10u
R1901
560
C2011
C2006
10u
C1002
0.1u
560k
R1602
2.7k
68k
IC1401
R1405
R1403
N.C
N.C
TEST4
HR
MOD2
GPS
SPIO
MON_29
SPOI
GND
VCC
TEST3
TEST2
VCS
MDN
PDP
MDW
GND
MDS
LPGC
GND
PWM
OPEN
C1003
MA716
R1301
3.6k
C1921
D1601
560k
OSCI
VSY
EXCL
18
19
R1601
Fig.3 Reference drive circuit
R1501
BLKO
1
C1502
N.C
0.1u
72
MON_55
R1960
220k
VR1902
100k
MON_56
82p
LCY00034-17
trD
tWHC
90
tfD
tWLC
90
10
10
10
10
tSUD
trP
tHD
tWHD1
tfP
90
90
10
10
trLC
90
tWHS
tfLC
90
90
10
10
tSUS
trS
tHS
tfS
90
90
10
tSUM
10
90
MODE2
10
WHITE
BLACK
VSM
BLACK
WHITE
VCDC
VGLDC
Fig.4
VCAC
VCAC
VGLAC
VGLAC
Input signal timing chart
LCY0005618
Fig.5 Package form
LCY00056 19
Appendix
Adjusting method of optimum common electrode DC bias voltage
To obtain optimum DC bias voltage of common electrode driving signal (VCDC), photoelectric devices are very
effective, and the accuracy is with 0.1V. (In visual examination method, the accuracy is about 0.5V because of the
difference among individuals.)
To gain optimum common electrode DC bias, there is the method that uses photoelectric
devices.
Measurement of flicker
DC bias voltage is adjusted so as to minimize NTSC : 60Hz(30Hz) / PAL : 50Hz(25Hz) flicker.
Photo-electric device
Output voltage
VCDC
LCD module
Oscilloscope
Fig. A Measurement system

Measurement of flicker
Photoelectric output voltage is measured by an oscilloscope at a system show in Fig. A.
DC bias voltage must be adjusted so as to minimize the NTSC : 60Hz (30Hz) / PAL :
50Hz
(25Hz) flicker with DC bias voltage changing slowly. (Fig.B)
DC bias : Optimum
DC bias : Optimum + 1
Fig. B Waveforms of flicker
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited
Warranty for SHARPs product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND
FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,
for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas

5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-2500
Fax: (1) 360-834-8903
Fast Info: (1) 800-833-9437
www.sharpsma.com
SHARP Microelectronics Europe

Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: (49) 40-2376-2286
Fax: (49) 40-2376-2232
www.sharpsme.com
SHARP Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com
TAIWAN
SINGAPORE
KOREA
SHARP Electronic Components

(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd.

438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855
SHARP Electronic Components

(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China

(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: [email protected]
SHARP-ROXY (Hong Kong) Ltd.

3rd Business Division,
17/F, Admiralty Centre, Tower 1
18 Harcourt Road, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 13B1, Tower C,
Electronics Science & Technology Building
Shen Nan Zhong Road
Shenzhen, P.R. China
Phone: (86) 755-3273731
Fax: (86) 755-3273735

Datasheet SHARP

Uploaded by

Copyright:

Available Formats

Datasheet SHARP

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Datasheet SHARP

Uploaded by

Copyright:

Available Formats

LQ070T3GR01

Color TFT LCD Module

Spec No.: LCY-00056A

datasheet pdf - http://www.DataSheet4U.net/

LIQUID CRYSTAL DISPLAY GROUP

DEVICE SPECIFICATION FOR

TFT - LCD module

datasheet pdf - http://www.DataSheet4U.net/

datasheet pdf - http://www.DataSheet4U.net/

Test and measurement equipment

datasheet pdf - http://www.DataSheet4U.net/

datasheet pdf - http://www.DataSheet4U.net/

Power supply for gate driver(High level).

Control signal for gate driver.

Control signal for gate driver.

Switching signal of scanning direction for gate driver.

Start signal for gate driver.

Clock signal for gate driver.

Power supply for logic circuit in gate driver.(High level)

Power supply for gate driver (Low level)

Common electrode driving signal.

Power supply for logic circuit in gate driver (Low level).

/o Start signal for source driver.

Control signal for source driver.

Power save signal.

Switching signal of scanning direction for source driver.

Color video signal (Blue)

Color video signal (Green)

Color video signal (Red)

Power supply for source driver (High level)

Power supply for source driver (High level)

Power supply for source driver (High level)

Power supply for source driver (High level)

o/i Start signal for source driver.

Input terminalhigh voltage side

Input terminallow voltage side

datasheet pdf - http://www.DataSheet4U.net/

The operating temperature only guarantees operation of the circuit.

datasheet pdf - http://www.DataSheet4U.net/

Inverter Harison Electric co. Ltd.

datasheet pdf - http://www.DataSheet4U.net/

Operating Clock frequency

7-3)Input signal timing chart

7-4)Signal for reverse scanning

High level = VSH, Low level = GND

Lamp power consumption

datasheet pdf - http://www.DataSheet4U.net/

Normal mode1 line writing

2 line same time writing mode

datasheet pdf - http://www.DataSheet4U.net/

DC/AC inverter driving frequency49kHz

mesuring method for optical characteristics

Note 6-1 Viewing angle range is defined as follows.

definition for viewing angle

datasheet pdf - http://www.DataSheet4U.net/

Contrast ratio is defined as follows:

Response time is obtained by measuring the transition time of photodetector

datasheet pdf - http://www.DataSheet4U.net/

(10) Display quality

11-2) Precautions in mounting