AF40 Error Codes

Fault codes - Automatic gearbox ECU AT6/AM6 (Summary)
C1325 Fault in communication on the CAN with the ABS/ESP ECU : Value received in
correct (Rear left-hand wheel)
C1335 Fault in communication on the CAN with the ABS/ESP ECU : Value received in
correct (Rear right-hand wheel)
P0115 Engine coolant temperature signal fault : Value received incorrect
P0218 Oil temperature warning light fault : The indicator light comes on(Thermal
protection pattern 3) : Engine torque reduction request
P0298 Oil wear counter fault : Value at upper limit
P0562 Battery voltage fault : Voltage too low
P0563 Battery voltage fault : Voltage too high
P0601 ECU fault : Processor
P0602 Telecharging fault
P0603 ECU fault : EEPROM
P0604 ECU fault : RAM
P0605 ECU fault : Flash ROM
P0715 Fault on the gearbox input speed sensor circuit : Value received incorrect
P0717 Fault on the gearbox input speed sensor circuit : No signal
P0720 Fault on the gearbox output speed sensor circuit : Value received incorrec
t
P0722 Fault on the gearbox output speed sensor circuit : No signal
P0727 Engine speed fault : Value received incorrect
P0729 Gearbox mechanical or hydraulic fault : Coherence on 6th gear
P0731 Gearbox mechanical or hydraulic fault : Coherence on first gear
P0732 Gearbox mechanical or hydraulic fault : Coherence in 2nd gear
P0733 Gearbox mechanical or hydraulic fault : Coherence in 3rd gear
P0734 Gearbox mechanical or hydraulic fault : Coherence in 4th gear
P0735 Gearbox mechanical or hydraulic fault : Coherence in 5th gear
P0736 Gearbox mechanical or hydraulic fault : Coherence on reverse gear
P0741 Converter lock-up fault : Lock-up impossible
P0742 Converter lock-up fault : Permanent lock-up
P0751 Mechanical or hydraulic fault on 1st gear with engine brake : Coherence
P0752 Mechanical or hydraulic fault on 1st gear : Coherence
P0756 Mechanical or hydraulic fault on 2nd gear : Coherence
P0761 Mechanical or hydraulic fault on the third gear : Coherence
P0765 Fault: detection of neutral complete (In 'D' mode)
P0766 Mechanical or hydraulic fault on the fourth gear : Coherence
P0771 Mechanical or hydraulic fault on the fifth gear : Coherence
P0772 Fault in engaging clutch C1 for reduction of drag in mode D
P0780 Fault: random gear changing : Coherence
P0819 Press control signal fault : Locking
P0826 Press control signal fault : Locking in position M+ or MP0882 Gearbox ECU supply voltage fault : Voltage too low
P0883 Gearbox ECU supply voltage fault : Voltage too high
P0928 Fault on the lever locking actuator circuit (shift-lock) : Open circuit or
short circuit to earth
P0931 Fault on the lever locking actuator circuit (shift-lock) : Short circuit t
o positive
P0938 Oil thermistor fault : High stop
P0939 Oil thermistor fault : Short circuit to earth
P0940 Oil thermistor fault : Open circuit or short circuit to the plus
P0961 Line pressure modulation electrovalve output fault : Coherence
P0962 Fault on the line pressure modulation electrovalve circuit : Open circuit
or short circuit to earth
P0963 Fault on the line pressure modulation electrovalve circuit : Short circuit
to positive
P0965 Brake pressure modulation electrovalve output fault (SLB1 : Coherence
P0966 Fault on the control circuit of the brake pressure modulation electrovalve
(SLB1) : Open circuit or short circuit to earth

P0967 Fault on the control circuit of the brake pressure modulation electrovalve
(SLB1) : Short circuit to positive
P0969 Clutch pressure modulation solenoid valve (SLC1) output fault : Coherence
P0970 Fault on the control circuit of the clutch pressure modulation electrovalv
e (SLC1) : Open circuit or short circuit to earth
e (SLC1) : Short circuit to positive
P0973 Fault on the solenoid circuit of sequence S1 : Short circuit to earth
P0974 Fault on the solenoid circuit of sequence S1 : Open circuit or short circu
it to the plus
P0976 Fault on the solenoid circuit of sequence S2 : Short circuit to earth
P0977 Fault on the solenoid circuit of sequence S2 : Open circuit or short circu
it to the plus
P1605 Fault in the information on torque requested by the driver sent by the eng
ine ECU : Value received incorrect
P160A ECU identification fault
P160E Supply cut-off during the powerlatch fault
P1613 Configuration fault
P1703 Fault in the accelerator pedal position information transmitted by the eng
ine management ECU : Value received incorrect
P1727 Fault in the actual engine torque information transmitted by the engine ma
nagement ECU : Value received incorrect
P1732 Fault on the gear lever position sensor : No signal
P1733 Fault on the gear lever position sensor : Coherence
P1737 Fault on the gear lever position sensor : Value received incorrect
P1771 Reduction of drag in D mode fault : Racing of the engine
P17A0 Fault on the key locking control circuit (key lock) : Open circuit or shor
t circuit to the plus
P17A1 Fault on the key locking control circuit (key lock) : Short circuit to ear
th
P17A2 Mechanical or hydraulic fault on reverse gear : Coherence
P17A3 Neutral detection fault (in mode R)
P17A5 Mechanical or hydraulic fault on 1st gear with engine brake : Coherence
P17A9 Neutral detection fault (in mode D)
P17AA Reduction of drag in D mode fault : Engaging of C1
P1800 Position N programming fault
P1828 Fault on the start lock control output : Short circuit to positive
P1829 Fault on the start lock control output : Open circuit or short circuit to
earth
P1830 Fault in the front wheels average speed information transmitted by ABS/ESP
: Value received incorrect
P1838 Gearbox mechanical or hydraulic fault : Coherence in first gear with engin
e brake
P1839 Reduction of drag in mode D activation fault : No check
P2707 Mechanical or hydraulic fault on 6th gear : Coherence
P2719 Clutch pressure modulation solenoid valve SLC2 output fault : Coherence
e SLC2 : Short circuit to earth or open circuit
e SLC2 : Short circuit to positive
P2728 Clutch pressure modulation solenoid valve SLC3 output fault : Coherence
e SLC3 : Open circuit or short circuit to earth
e SLC3 : Short circuit to positive
P2762 Torque converter lock-up pressure modulation electrovalve output fault : C
oherence
P2763 Faults in the control circuit of the lock-up pressure modulation solenoid
valve of the SLU converter : Short circuit to positive
P2764
valve
P2775
P2776
P2777
Faults in the control circuit of the lock-up pressure modulation solenoid

of the SLU converter : Open circuit or short circuit to earth
Fault in the one-touch signal+ : Value received incorrect
Fault in the one-touch signal+ : Short circuit to earth
Fault in the one-touch signal+ : Open circuit or short circuit to the plus
P2779 Fault in the one-touch signal - : Value received incorrect

P2780 Fault in the one-touch signal - : Short circuit to earth
P2781 Fault in the one-touch signal - : Open circuit or short circuit to the plu
s
U1000 Communication fault on the CAN between the automatic gearbox ECU and the o
ther ECUs of the network : No signal
U1003 CAN communication fault : No signal
U1105 Fault in communication on the CAN network with the steering wheel angle se
nsor : No signal
U1108 Fault in communication on the CAN with the engine management ECU : No sign
al
U1110 Fault in communication on the CAN with the automatic gearbox electric cont
rol ECU : No signal
U1113 Fault in communication on the CAN with the ABS/ESP ECU : No signal
U1118 Fault in communication on the CAN with the built-in systems interface(BSI)
: No signal
U1205 Fault in the information received by the steering wheel angle sensor over
the CAN network : Value received incorrect
U1208 Fault in the information sent by the engine management ECU over the CAN ne
twork : Value received incorrect
U1213 Fault in the information transmitted by the ABS/ESP ECU on the CAN network
: Value received incorrect
U1218 Fault in the outside air temperature received on the CAN network (Engine E
CU) : Value received incorrect
U1308 Fault in communication with the engine ECU on the CAN network : No signal
U1310 Fault in communication of the gearbox electric control on the CAN : Value
received incorrect or not received
U1313 Fault in communication with the ABS/ESP ECU on the CAN : No signal
U1318 Fault in communication with the built-in systems interface on the CAN : No
signal
U2000 Fault in receipt of the main triggering request information received on th
e CAN : Absence of signal or value received incorrect
U2003 Fault in receipt of the controlled main triggering request information rec
eived on the CAN : Coherence

AF40 Error Codes

Uploaded by

Copyright:

Available Formats

AF40 Error Codes

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AF40 Error Codes

Uploaded by

Copyright:

Available Formats

Fault codes - Automatic gearbox ECU AT6/AM6 (Summary)

(SLB1) : Open circuit or short circuit to earth

Faults in the control circuit of the lock-up pressure modulation solenoid

P2779 Fault in the one-touch signal - : Value received incorrect

You might also like