Title of The Report: Heat Transfer Through An Extended Surface

Title of the report: Heat transfer through an extended surface.
Heat transfer through an extended surface.

ME323: FLUID MECHANICS LABORATORY
Submitted By:
Submitted To:
Submitted:
Page | 1
1. ABSTRACT
The principal objective of this experiment is to measure the temperature distribution
along the extended surface and then compare it with the theoretical data. Also the
calculation of heat transferred from an extended surface by radiation and convection
heat transfer method and then comparing it with the theoretical results. The objective
is also to calculate the thermal conductivity of the material.
To achieve the above mentioned objectives, I use the method that includes the
heating of one end of a solid cylinder road and measuring the temperature
distribution along the surface of rod by temperature measuring techniques. The
equipment that is used in this experiment is the use of HT10X Heat Transfer Service
Unit, HT15 Extended Surface Heat Transfer Accessory, and PC with HT10X-90IFD
Data Logging Accessory. With the help of these equipments, the desired results
would be achieved.
The results of this experiment shows that by measuring the surface temperature
from the experiment and theoretical temperature profile and plot them against each
other clearly showing the data points on the graph. All the calculation shows us that
by measuring the heat input to the heater, we are able to calculate how much heat is
lost from the rod. Using these calculations, have measured the thermal conductivity
of the rod.
Page | 2
2. Data and Results:

Part I.
Find the value of constant m using any iterative technique for thermocouple
T1 to T8 (the initial guess for the value of m can be taken 8.0).
Calculate the theoretical temperature Tx at each point along the rod using
average value of m.
Estimate the cumulative influence of the experimental errors on your
calculated values for m and measured values for T1 to T9, x and L.
Plot measured surface temperature Tx from experiment and theoretical
temperature profile (calculated using average value of m) against position x
(in same plot) along the extended surface clearly showing the data points on
the plot.
Part II.
Compare the measured power Qin to the heater with the calculated heat
loss Qtot from the rod.
Part III.
Compare the measured thermal conductivity with the suggested thermal
conductivity for brass rod kbrass = 121 Wm-2K-1
Page | 3
Page | 4
Page | 5
Page | 6
Page | 7
Page | 8
Page | 9
Page | 10
Page | 11
Page | 12
Page | 13
Page | 14
Page | 15
Page | 16
Page | 17
Page | 18
Page | 19
Page | 20
Page | 21
Page | 22
Page | 23
Page | 24
Page | 25
Measurement for 9 V
Heater Voltage V (V) :

Heater current I (A) :
Heater Power Qin (W) :
Page | 26
Thermocouple
Number
T1
T2
T3
T4
T5
T6
T7
T8
T9
Page | 27
Description
Location (cm)
Page | 28
Page | 29
Time 1:
Temperature
Page | 30
Time 2:
Tx (C)
Page | 31
Time 3:
Page | 32
Page | 33
Measurement for 12 V
Page | 34

Thermocouple
Number
T1
T2
T3
Page | 35
T4
T5
T6
T7
T8
T9
Description
Page | 36
Location (cm)
Page | 37
Time 1:
Page | 38
Temperature
Time 2:
Page | 39
Tx (C)
Page | 40
Time 3:
Page | 41
Measurement for 16 V

Page | 42
Thermocouple
Number
T1
T2
T3
T4
T5
T6
T7
Page | 43
T8
T9
Description
Page | 44
Location (cm)
Page | 45
Time 1:
Temperature
Page | 46
Time 2:
Tx (C)
Page | 47
Time 3:
Page | 48
Page | 49
3. Theory and Analysis:

The extended surface is a special case of heat transfer in which the heat is transferred from the solid
of the rod by conduction and by convection from the boundaries of the solid. The direction of heat
transfer in extended surfaces from the boundaries is perpendicular to the principal direction of heat
transfer in the solid. A temperature gradient always exists due to the conductivity of the material and
heat loss to the surroundings. The temperature distribution along the fin or pin must be known to
determine the heat transfer from the surface to its surroundings. As conduction and convection occurs
simultaneously so we also have to consider the effect of both.
Conduction is means of heat transfer by molecular action within the material without any motion of the
material as a whole. If one end of the rod is at higher temperature than the lower end , the heat
transfers to the colder end . As this is the law of nature every material or everything which is at high
state tries to move towards the low state. Upon this law, the method of conduction takes place.
Heat energy transferred between a surface and a moving fluid at different temperatures is known as
convection. In reality this is a combination of diffusion and bulk motion of molecules. Near the surface
the fluid velocity is low, and diffusion dominates. Away from the surface, bulk motion increase the
influence and dominates.
By considering the steady-state energy balance for an extended surface of uniform material and crosssectional area, the following equation can be derived:
d 2 ( x )
d x2
Where
2
- m ( x )=0
m=
(1)
HP
( x ) =T x T a
k brass A ;
Page | 50
Since H, P, Kbrass and A are constant for a given rod with fixed power input, therefore
m2 must be a
constant
Assuming that the diameter of the pin is small in comparison with its length then heat loss at the tip
can be assumed to be negligible (at the tip x=L).
d(x)
=0 at x=L
dx
(2)
Therefore:
(x) T x T a cosh m( Lx )
=
=
T 1 T a
cosh mL
(3)
Note that the magnitude of the temperature gradient decreases with increasing x. This trend is a
consequence of the reduction in the conduction heat transfer with increasing x due to continuous
convection and radiation losses from the fin surface.
Part II.
The total heat loss from the rod can be calculated as follows: Q tot = H A s (Ts Ta) (W)
Where the heat transfer coefficient (HTC) H is the combined coefficient due to natural convection and
radiation, i.e. H = Hc + Hr (Wm-2K-1)
Page | 51
And As = D L (Total area of the extended surface)

Where: L = Length of the rod (distance from T1 to T8) = 35 cm
Note: The distance between each thermocouple is 5 cm starting from 0.0 cm at T1.
D = Diameter of the rod = 1 cm

Ts = Average surface temperature of the rod (averaged from temperature T1 to T8) T a = Ambient air
temperature (T9)
The average CHT Hc can be calculated from the formula given below :
N u c=
HcD
n
=CR a D
k
(4)
WHere
a
T sT
D3
g
R a D=
(5)
R ad
10
10
10
0.675
0.058
Page | 52
10 10
1.02
0.148
0.85
0.188
0.480
0.250
12
0.125
0.333
10 10
10 10
10 10
The thermal conductivity is calculated by :

k brass
HP
m2 A
(6)
A = Cross sectional area of the pin =
Where P = Perimeter of the pin =
D2
4
Procedure:
The procedure to perform this experiment is that we first have to switch on the main switch. Now set
the heater voltage to 20V with the help of potentiometer. Now monitor the temperature T1 regularly
and when temperature reaches 80C, reduce the heater voltage to 9 voltage. Now allow the
temperature to become stabilize to reach the steady state.
Now record the voltage and current supplied to the heater. Record the temperature at each position
along the rod (T1 to T8) and ambient air temperature (T9). At the end set the heater voltage to 12volts
to 16 bolts and follows the above steps.
4. Conclusions:
Page | 53
As calculating the theoretical power that is transferred to heat the rod is known, but with the help of
these equations, net heat lost from the extended surface is calculated and all the results are verified by
using above method. Here neglecting the human error and considering that all the heat supplied is to
heat the rod and increase the temperature of the system.
Practical applications:
For the heat transfer, fins are the best example that extends an object to increase the heat transfer by
increasing convection. As we already know amount of conduction, convection and radiation of an
object determines the rate of heat as how much heat is transferred. We can increase the amount of
heat transferred by increasing the temperature gradient, increasing the convection heat transfer
coefficient or by simply increasing the surface area. Thus first two options are not so feasible so
adding a fin to an object increases the surface area and would be the economical solution to heat
transfer.
5. References:
Website:
http://hyperphysics.phy-astr.gsu.edu/hbase/thermo/heatra.html
http://www.engineeringtoolbox.com/convective-heat-transfer-d_430.html
Paper:
Lab Report content: ME-341, Heat and Mass Transfer
Department of Mechanical Engineering
Indian Institute of Technology, Kanpur
Kanpur (UP) 208016, INDIA
6. Appendix:
Equation 1
Steady state energy balance equation
Page | 54
.Equation 2
To make the heat loss negligible.
Equation 3
Consequence of the reduction in the conduction heat transfer
Equation 4,5
The average CHT can be calculated
Equation 6
Calculation of thermal conductivity
Page | 55

Title of The Report: Heat Transfer Through An Extended Surface

Uploaded by

Copyright:

Available Formats

Title of The Report: Heat Transfer Through An Extended Surface

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Title of The Report: Heat Transfer Through An Extended Surface

Uploaded by

Copyright:

Available Formats

Title of the report: Heat transfer through an extended surface.

Heat transfer through an extended surface.

Heat transfer through an extended surface.

Heat transfer through an extended surface.

2. Data and Results:

Heater Voltage V (V) :

Heater Power Qin (W) :

Heater Voltage V (V) :

Heater Power Qin (W) :

Heater Voltage V (V) :

Heater Power Qin (W) :

Heat transfer through an extended surface.

3. Theory and Analysis:

Heat transfer through an extended surface.

And As = D L (Total area of the extended surface)

D = Diameter of the rod = 1 cm

The thermal conductivity is calculated by :

Heat transfer through an extended surface.

A = Cross sectional area of the pin =

Where P = Perimeter of the pin =

You might also like