Scribd
Upload
260 views2 pages

ASM Vs RAID - Oracle Community

ASM is not directly intended as a replacement for RAID, but can provide some similar functionality with its mirroring capabilities. There are four main configuration options that involve different combinations of using ASM with or without RAID on disks. The best configuration depends on factors like hardware costs, administrative overhead, performance needs, and high availability requirements. While ASM alone can provide redundancy, integrating RAID can improve I/O and offer automatic redundancy without additional database administration.

Uploaded by

pravin2projects
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
260 views2 pages

ASM Vs RAID - Oracle Community

ASM is not directly intended as a replacement for RAID, but can provide some similar functionality with its mirroring capabilities. There are four main configuration options that involve different combinations of using ASM with or without RAID on disks. The best configuration depends on factors like hardware costs, administrative overhead, performance needs, and high availability requirements. While ASM alone can provide redundancy, integrating RAID can improve I/O and offer automatic redundancy without additional database administration.

Uploaded by

pravin2projects
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

9/19/2015

ASM vs RAID | Oracle Community

All Places > Databas e > High Availability > Autom atic Storage Managem ent > Dis cus s ions
THIS DISCUSSION IS ARCHIVED

1 Reply

Latest reply: Feb 28, 2011 3:10 PM by 619534

714304 Feb 28, 2011 1:10 AM

ASM vs RAID
This question is Not Answered.

I have a doubt whether ASM is a Replacement for RAID


for example can we totally foget RAID storage and go for normal IDE or SATA disk and
configure the storage with ASM... ? I hope some expert can explain this
Thanks
Lbn76

1807 Views

Tags: asm, external, normal, raid, redundancy

Average User Rating


(0 ratings )

619534 Feb 28, 2011 3:10 PM (in response to 714304)

1. Re: ASM vs RAID


ASM isn't intended as a direct replacement for RAID, although with ASM mirroring, the functionality can be similar - a lot of it is going to depend on your
needs, your budget, your current disk configuration, and comfort in managing either solution.
To super-simplify some of the key points, you basically have 4 configuration options that are available to you:
ASM (External Redundancy) and Disk (non-RAID):
- You don't want to run in this configuration for any systems that require uptime. If ASM is set to "external", where there is no software redundancy, and
the disks are not part of a RAID group, any failure of a single disk will cause a loss of data on the ASM diskgroup. (We don't even run this in our Lab
environments, but it is possible - just not recommended).
ASM (Normal/High Redundancy) and Disk (non-RAID):
- Allows DBA to manage Failure Groups and file protection within ASM, which can be a great asset for an organization where there is no SAN
management, but DBA is responsible for correct configuration to prevent outages during failures - and more importantly, responsible for monitoring failure
groups to ensure adequate space for failure.
- Places the burden of mirroring on the Software, and therefore the cluster host(s).
- Loss of a disk relies on ASM (and proper Diskgroup/File Protection configuration!) to allow continued/uninterrupted processing (assuming the Failure
group is not on the same physical device).
- Maximizes Capacity, but not necessarily I/O
ASM (External Redundancy) and Disk (RAID)
- Removes administrative overhead of managing Failure groups and file protection for the DBA, but DBA should work with Storage Admins to ensure
protection exists at the storage layer (correct RAID configuration, hot spares, etc.)
- Places the burden of mirroring on the disk array/controller card. RAID controllers offload the mirroring/striping work from the cluster, usually allowing for
a performance improvement when compared to ASM redundancy alone.
- Loss of a disk (in a properly configured RAID group) is transparent to ASM, the DBA, and the end-user, assuming the loss is only at the disk level
within a RAID group, not a storage-device level loss or RAID group logical corruption.
- Depending on configuration (RAID-5 vs. 0+1, normally), capacity and/or I/O can be an issue - DBA should work with the Storage Admins to determine
correct requirements.
- In my personal experience ONLY this is the most common setup I've seen.

https://community.oracle.com/message/9402230

1/2

9/19/2015

ASM vs RAID | Oracle Community


ASM (Normal/High Redundancy) and Disk (RAID)
- Administrative overhead rests on BOTH the DBA and Storage Administrator - potential for great redundancy, but at a cost of more potential failure
points.
- Processing overhead is doubled - Host CPU is utilized for ASM striping/mirroring, RAID controller utilized for RAID striping/mirroring. This will likely
result in some degraded performance if not carefully managed/planned for.
- Best Redundancy available - If Failure groups are segregated into different RAID groups (or even storage controllers/SANs) properly, and RAID is
properly configured, even total SAN outages (planned or unplanned) wouldn't impact the database availability.
- High cost of hardware - for example, assuming a full-sized failure group on ASM (2x disk) and RAID-10 (2x disk again), you're looking at a potentially
cost-prohibitive configuration, especially when considering IOPS and throughput requirements, number of spindles, etc. - costs can get high very
quickly.
Again, this is just a quick overview of ASM Failure Groups and RAID - ultimately, the decision will need to be based on your specific environment's
needs, taking into account budget/costs, administrative abilities and overhead (do you have a storage admin? a 10-man SAN team? One DBA or 20?),
database size, availability requirements, throughput/IOPs, etc.
Some more great info from Levi Pereira on ASM striping (with more links embedded within):
Re: Oracle 10.2 ASM on AIX 5.3 compatibility with IBM DS4300 & EXP700 storage

Actions

Like (1)

About Oracle Technology Network (OTN)

Powered by

Oracle Technology Network


Oracle Com m unities Directory FAQ
About Oracle Oracle and Sun RSS Feeds Subscribe Careers Contact Us Site Maps Legal Notices Term s of Use Your Privacy Rights Cookie Preferences

https://community.oracle.com/message/9402230

2/2

You might also like