PCS 7 - Documentation

SIMATIC
Process Control System PCS 7

PCS 7 Documentation (V8.1)
Catalog Overview
Valid for PCS 7 as of V8.1
07/2014
A5E32711791-AA
Options for Accessing

Documentation
Documentation for the

Planning Phase
Documentation for the

Realization Phase
Documentation on
commissioning, operation,
diagnostics and servicing
Legal information
Warning notice system
This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent
damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert
symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are
graded according to the degree of danger.
DANGER
indicates that death or severe personal injury will result if proper precautions are not taken.
WARNING
indicates that death or severe personal injury may result if proper precautions are not taken.
CAUTION
indicates that minor personal injury can result if proper precautions are not taken.
NOTICE
indicates that property damage can result if proper precautions are not taken.
If more than one degree of danger is present, the warning notice representing the highest degree of danger will be
used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property
damage.
Qualified Personnel
The product/system described in this documentation may be operated only by personnel qualified for the specific
task in accordance with the relevant documentation, in particular its warning notices and safety instructions. Qualified
personnel are those who, based on their training and experience, are capable of identifying risks and avoiding
potential hazards when working with these products/systems.
Proper use of Siemens products

Note the following:
WARNING
Siemens products may only be used for the applications described in the catalog and in the relevant technical
documentation. If products and components from other manufacturers are used, these must be recommended or
approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and
maintenance are required to ensure that the products operate safely and without any problems. The permissible
ambient conditions must be complied with. The information in the relevant documentation must be observed.
Trademarks
All names identified by are registered trademarks of Siemens AG. The remaining trademarks in this publication
may be trademarks whose use by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency with the hardware and software described.
Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in
this publication is reviewed regularly and any necessary corrections are included in subsequent editions.
Siemens AG
Industry Sector
Postfach 48 48
90026 NRNBERG
GERMANY
A5E32711791-AA
07/2014 Subject to change
Copyright Siemens AG 2014.

All rights reserved
Table of contents
1
Options for Accessing Documentation.........................................................................................................5
Documentation for the Planning Phase........................................................................................................9
Documentation for the Realization Phase..................................................................................................11
Documentation on commissioning, operation, diagnostics and servicing..................................................17

Index...........................................................................................................................................................19

Catalog Overview, 07/2014, A5E32711791-AA
Options for Accessing Documentation
This documentation gives you an overview of the most important documents available for PCS
7. The following sections are assigned to the phases of a plant. You can find information on
available and required documentation for each phase.
Phases:
Planning (Page 9)
Implementation (Page 11)
Commissioning, operation, diagnostics and servicing (Page 17)
Types of documentation
The documentation required for PCS 7 includes the following types:
Readme
The information given in the PCS 7 readme takes precedence over all PCS 7
documentation.
System documentation
System documentation contains information that covers several products, such as
configuration manuals and Getting Started manuals. This documentation serves as a
guideline for the overall system and explains the interaction between the individual
hardware and software components.
See the note on the "PCS 7 Documentation Portal Setup" in the paragraph below.
Product documentation
Product documentation contains information about special hardware and software
components. The individual documents provide detailed information on the specific
component.
Access options
You can find the PCS 7 documentation at the following locations:
On the Process Control System; SIMATIC PCS 7 DVD
After installation, on the computer
In the Internet

Full versions of the documentation are available at the website of the "SIMATIC PCS 7
Technical Documentation": www.siemens.com/pcs7-documentation (www.siemens.com/
pcs7-documentation)
Note
PCS 7 Readme (Internet version)
The information provided in the PCS 7 Readme in the Internet takes precedence over all PCS
7 documentation.
Please read this PCS 7 Readme carefully; it contains important information and amendments
on PCS 7.
Documentation for PCS 7 on the Process Control System; SIMATIC PCS 7 DVD
PCS 7 Readme (DVD version)
The PCS 7 Readme on the Process Control System; SIMATIC PCS 7 DVD contains
important information regarding PCS 7 and takes precedence over the PCS 7
documentation supplied. After installation of PCS 7, you can find the document Process
Control System PCS 7; PCS 7 Readme in the Windows Start menu under the following path:
Siemens Automation > SIMATIC > Product Notes > <Language>
The most important PCS 7 system documentation may be found at the following locations:
On the SIMATIC PCS 7 DVD in the "_Manuals" folder.
On the Engineering Station as online help (CHM file) for the SIMATIC Manager
application
On the Engineering Station as a PDF file in the Windows Start menu under the following
path:
Siemens Automation > SIMATIC > Documentation > <Language>
Note
The following PCS 7 system documentation is included:
Catalog overview Process Control System PCS 7; PCS 7 Documentation
Configuration manual Process Control System PCS 7; Engineering System
Function manual Process Control System PCS 7; PCS 7 - PC Configuration
Configuration manual Process Control System PCS 7; Operator Station
Function manual Process Control System PCS 7;.OS Process Control
The product documentation is installed with the respective product.
Documentation for PCS 7 in the Internet (current versions)
The latest documentation on the PCS 7 versions is available at the website of the "SIMATIC
PCS 7 Technical Documentation":

In the section "Manuals for SIMATIC PCS 7 ..."

The link to the latest system and product documentation of the respective PCS 7 version.
The link to download the Setup for the latest system documentation
"PCS 7 Documentation Portal Setup".
Note
PCS 7 Documentation Portal Setup
Setup includes the complete system documentation for PCS 7 (PDF files and online
help).
You can install this Setup without PCS 7.
The following documentation is updated when you install the Setup on the
Engineering Station (completed or overwritten when selecting the original
installation folder):
Online help of the "SIMATIC Manager" application: (CHM files)
System documentation for PCS 7 in the Windows Start menu:
Siemens Automation > SIMATIC > Documentation > Language > PDF files
The PCS 7 Newsletter keeps you informed about when new versions of the system
documentation become available.
The link to download the entire PCS 7 documentation as Manual Collection in the My
Documentation Manager (http://support.automation.siemens.com/WW/view/en/
38715968).
The Manual Collection includes the manuals for hardware and software.
In the section "Hardware Manuals for SIMATIC PCS 7 ..."
The link to the latest manuals for components approved for a PCS 7 version.
The link to the latest manuals for approved SIMATIC PCS 7 industry software for a PCS
7.
Catalogs, brochures, customer magazines and demo software
This information is available in the Internet at: Information and Download Center (http://
www.automation.siemens.com/mcms/infocenter)

Documentation for the Planning Phase
Overview
You can find the following PCS 7 documentation in the table below:
Documentation that provides an overview of the systems and components for PCS 7.
Documentation that supports you in planning your PCS 7 plant.
Documentation
Content
Information about the range of services

Catalog ST PCS 7
Standard catalog for system components of a PCS 7 plant

Ordering information for all hardware and software components you may require for
automation with PCS 7.
Catalog ST PCS 7 T
Standard catalog for technological components for SIMATIC PCS 7

Integrated technologies, industry expertise and service for more productivity, energy
efficiency and flexibility.
Ordering information for technological components that can be integrated in your PCS 7
plant for complete solutions.
Catalog ST PCS 7 AO
Standard catalog for add-ons for SIMATIC PCS 7

Drive and automation solutions based on Totally Integrated Automation (TIA) and Totally
Integrated Power (TIP) for implementation in manufacturing, process and building
automation.
Ordering information for add-ons for SIMATIC PCS 7 that can be integrated in your PCS
7 plant for complete solutions.
Catalog CA 01
Products for automation and drive engineering - interactive catalog CA 01 (DVD)
Specifying the components and the systems for the PCS 7 plant
Configuration manual
PCS 7 Engineering System
Section "Engineering system":

Capacity options in configuring a PCS 7 plant
Selecting the network components
Selecting PC components for engineering and operator control and monitoring
Selecting AS components
Selecting I/O components
Preparations for efficient engineering
Manual PCS 7 PC
Configuration
Comprehensive overview of PC configurations for engineering and operator control and

monitoring:
Areas of application for the various PC configurations
Design and configuration of the PC networks
Required hardware and software for the PC components
Operating Manual
Process Safety including two checklists

Process Control System PCS 7; Realization of the fail-safe part of an S7 program using the following F-software
Compendium Part B Process components:
Safety
S7 F Systems
Safety Matrix Engineering Tool

Documentation for the Planning Phase
Documentation
Content
Operating Manual
Definition and description of test points for the hardware installation of process-related
production facilities.
Process Control System PCS 7;

Compendium Part E
Lines and connection technology
Hardware Installation
Configuration and design of control cabinets
Earthing, potential equalization and lightning protection
Bus lines
Whitepaper
Security Concept PCS 7 and

WinCC
Guide for network administrators for planning and installation of securely networked PCS
7 plants with connected PCS 7 Web clients, SIMATIC IT applications and customerspecific office networks:
Planning security cells and access points
Managing computers and users
Managing user permissions and access rights in PCS 7 and integration in the Windows
management
Implementing patch management
Secure network access to security cells
Operating Manual
Guidelines for planning IT security in automation technology
Process Control System PCS 7; Physical security measures

Compendium Part F Industrial Organizational security measures
Security
Access points
System hardening
Patch management
Malware detection & prevention
List PCS 7 - Enabled modules
List of modules released for PCS 7 versions
Function manual PCS 7 Time
Support for planning time synchronization in a PCS 7 plant
Used for data import and for bulk processing

Data is imported into AdvES from process tag or signal lists and adopted in PCS 7.
The documentation can be found in the Internet at the Siemens Industry Online Support
(http://support.automation.siemens.com).
Synchronization
Advanced Engineering System
10

Documentation for the Realization Phase
Overview
Documentation providing support for installing the PCS 7 software
Documentation providing support for configuring the wiring of the hardware
Documentation explaining the basic concept of engineering with PCS 7
Documentation which helps you to fully configure your PCS 7 plant
Documentation
Content
Installation
PCS 7 readme
Latest information with information about installation and using PCS 7 software
PCS 7 What's new?
Compact summary of the new or changed features in PCS 7 in comparison to previous

versions
Manual PCS 7 PC
Configuration
Installation instructions and settings for PC configurations for engineering and operator
control and monitoring:
Operating system
PCS 7 software
Special hardware and software
Whitepaper Security Concept

PCS 7 and WinCC
Guide for network administrators for planning and installation of securely networked PCS
7 plants with connected PCS 7 Web clients, SIMATIC IT applications and customer-specific
office networks:
Planning security cells and access points
Managing computers and users
Managing user permissions and access rights in PCS 7 and integration in the Windows
management
Implementing patch management
Secure network access to security cells
First Steps
Getting Started PCS 7 - First
Steps
Uses a simple example project to show you the fundamental procedures and the interaction
of the software components of SIMATIC PCS 7 during engineering and runtime.
Time required for tutorial: approx. 1 hour
Assembling components and systems

Configuration manual PCS 7
Engineering System
In the section "Configuration of PCS 7 Plants":

Basic configurations of a PCS 7 plant
Guide to the Installation Instructions for the Products
Special considerations, differences between PCS 7 and specifications in the product
installation instructions
Rules for plant changes in runtime (CiR)
Installation Guidelines for PCS 7: EMC and lightning protection

11
Documentation
Content
Application for data import and bulk processing
Advanced Engineering System
Generation of control modules from signal lists

Generation of control modules from process tag lists
Creation of hardware configurations from signal lists (including the symbol table)
Use of control module types from PCS 7 (BCM and customer-specific)
Definition of variants with optional blocks
Bulk processing of control modules, signals, parameters and messages
Checking data consistency and validity
Generation of PCS 7 automation data
Use of messages at control modules
Function manual Time

synchronization
Instructions for configuration and parameter assignment of time synchronization
Manuals for the automation

system S7-400H/FH
Instructions for configuring automation systems

Memory concept and startup scenarios
Cycle and reaction times
Technical specifications
Operation lists
System manual CPU 410-5H
Process Automation
Instructions for configuring the AS 410 automation system

Memory concept and startup scenarios
Cycle and reaction times
Operation lists
Manuals for S7-300 I/O

Modules
Manuals on CPs and FMs
(S7400, S7300)
Manuals for ET 200
components
ET 200M
Manual for hardware configuration and parameter assignment of components

ET 200S
ET 200SP
ET 200iSP
ET 200pro
Manuals for additional DP
components:
Diagnostic repeaters

DP/PA-Link
FF Link
Y-Link
DP/AS-i-Link
12

Documentation
Content
Manuals for industrial

networks, e.g:
Topologies and network configuration
Industrial Ethernet
Configuration of the communication
PROFIBUS
PROFINET
Manuals for SIMATIC NET
Topologies and network configuration
components: CPs for Industrial Installation instructions
Ethernet and PROFIBUS,
SCALANCE X, etc.
Engineering
Getting Started
PCS 7 - Part 1
Introduction to the basic functions of PCS 7 based on the PCS 7 example project "COLOR".
It contains the most important background information required to understand the individual
engineering tasks and detailed instructions for step-by-step post-configuration. You activate
OS process mode once configuration is complete.
We recommend working through this Getting Started tutorial before beginning work with the
PCS 7 Engineering System configuration manual.
Time required for tutorial: approx. 16 hours
Getting Started
PCS 7 - Part 2
Introduction to Using the Efficient Engineering functions in PCS 7. The basis for this is the
PCS 7 "COLOR" project in Getting Started PCS 7 - Part 1.
We recommend working through this Getting Started tutorial if you plan to configure large
PCS 7 plants with a large number of process tags.
Time required for tutorial: approx. 16 hours
SIMATIC BATCH Getting

Started
Introduction of the basic functions of SIMATIC BATCH. It contains the most important
background information required to understand the individual engineering tasks and
detailed instructions for step-by-step post-configuration. You activate process mode once
configuration is complete.
It is advisable to study this Getting Started before you work with SIMATIC BATCH.
PCS 7 manual
Step-by step instructions for migrating your PCS 7 project from PCS 7 V7.1 SP4 to V8.1
without subsequent utilization of new PCS 7 functions.
PCS 7 manual
Step-by-step instructions for migrating your PCS 7 project from PCS 7 V7.1 SP4 to V8.1
with subsequent utilization of new PCS 7 functions.

Engineering System
Sections for configuring the engineering system:
Software Update without

Utilization of the New
Functions
Software Update without
Utilization of the New
Functions
Basic concepts of engineering

Configuration of the engineering system
Configuring in the PCS 7 Engineering System
Compiling, downloading, testing, archiving and documenting project data

13
Documentation
Content
Complete information about configuring the operator station and the HMI system of PCS 7:
Operator Station
Configuring OS data
Creating process pictures
Message system settings
Options for archiving
Downloading a project and configuration changes
Time synchronization and lifebeat monitoring
Using server-server communication
Manual PCS 7 Maintenance

Station
Using diagnostic functions (Maintenance Station)
Manual PCS 7
Web Option for OS
Using PCS 7 Web Server and PCS 7 Web Client
System manual SIMATIC;

Process Historian
Administration
Use of the external archive server, "Process Historian"

Information Server
Administration
Use of the reporting system, "Information Server"
Archiving system that is used to store process data such as process values and messages.
Reporting system for historical data of process values, messages or recipe data. Data
sources can be stations:
Process Historian
PCS 7 OS
WinCC
Manual
SIMATIC PCS 7/SIMATIC IT

Integration Manual
Information for a better understanding of the integration of MES functions in PCS 7 with
SIMATIC IT:
Basics of SIMATIC IT and PCS 7
Implementing the ISA-95/ISA-88 standards
Integration of SIMATIC IT Historian and SIMATIC BATCH
Data management in SIMATIC IT and PCS 7
Functionality and data communication and data flow
Configuration procedure based on an example project
Operating manual PCS 7
SIMATIC BATCH
Complete information about configuring the BATCH station, the system for automating batch
processes:
Technological basis according to ISA-88.01
Configuring batch plant data
Creating recipes
Planning and controlling batches
Managing and archiving batch data
Manual PCS 7
SIMATIC Route Control
Complete information about configuring the route control station, the system for controlling
routes:
Creating the program for route control
Functions of the block library
Configuring materials and transport routes
Function manual PCS 7 Fault- Description of the solution concepts, function mechanisms and most important
tolerant Process Control
configurations for installing fault-tolerant systems with PCS 7. It will show you the faultSystems
tolerant solutions at all levels of automation (control level, process level, field level).
Function manual PCS 7 High-
precision Stamping
14
Comprehensive overview of required components, the interaction among the components

and their configuration for using high-precision time stamps

Documentation
Content
Function manual PCS 7 Time
Synchronization
Comprehensive overview of required components, the interaction among the components,

and their configuration for using time synchronization.
Manual PCS 7 Basis Library
Driver and diagnostic blocks

Description of methods of operation, block I/Os and input/output fields of the respective
faceplates
Manual PCS 7
Advanced Process Library
Process automation blocks - expandable
Operating Manual
Configuration guidelines including checklist
Description of methods of operation, block I/Os and input/output fields of the respective
faceplates
Process Control System PCS

7; Compendium Part A
Configuration Guidelines
Operator manual
Process Control System

SIMATIC PCS 7;
Compendium Part C
Equipment Phases with SFC
Types
Manual PCS 7 Programming
for Instructions for Blocks
Realization of technical functions using SFC types.

Functions for plants with continuous processes
Integration of SIMATIC BATCH
Solutions and recommendations
Information, design guidelines and rules for adapting project-specific blocks to the "Standard
Library". Explanation of how AS blocks and faceplates conforming to PCS 7 are created to
achieve the following:
Monitor parameter values through a faceplate
Control parameter values and therefore the reactions of blocks through a faceplate
Report asynchronously occurring events and block states on the OS and display them
in a faceplate or a WinCC message list
Manual Programming
ManualAPL Styleguide
Information, design guidelines and rules for adapting project-specific blocks to the
"Advanced Process Library".
(separately ordered)
Manuals for the individual

engineering tools: CFC, SFC,
STEP 7, SFC Visualization,
PDM, WinCC, LT Options,
SCL, DOCPRO
Basics of the engineering tool

Working with the engineering tool
Testing and commissioning the engineering tool
Readme and What's new for

Latest information with notes about installation of the engineering tool
the individual engineering
Compact summary of the new or changed features in comparison to previous versions
tools: CFC, SFC, STEP 7, SFC
visualization, PDM, SCL,
DOCPRO
PCS 7 FOUNDATION
Fieldbus documentation
Description of the solution concepts, functional mechanisms and most important

configurations for the integration of devices on a FOUNDATION Fieldbus in PCS 7.

15
Documentation on commissioning, operation,

diagnostics and servicing
Overview
Documentation providing support for commissioning and operating in process mode
Documentation providing support for performing servicing
Documentation
Content
Process mode
Manual PCS 7
OS Process Control
Graphical user interface and operator input at the PCS 7 OS in process mode:
Message system
Trend system
Group display
Operator process control
Manual PCS 7
Web Option for OS
Working with PCS 7 Web Client/PCS 7 Web Diagnose Client
Manual PCS 7
Maintenance Station
Using diagnostic functions (Maintenance Station)

Information Server Operating
Manual
Use of the reporting system, "Information Server"

Collection, evaluation and graphic display of process values, messages and recipe data
of a process control system
Manual PCS 7
Route control
SIMATIC Route Control

Manual PCS 7 Service Support
and Diagnostics
Managing and logging routes

This documentation is aimed at trained service personnel (Service Level 1): PCS 7 users
and SIMATIC S7 specialists
This manual contains the information to support you in the following tasks:
Ensuring availability of your PCS 7 plant
Understanding the alarm concept of your PCS 7 plant
Finding the right diagnostic tools when a fault occurs
Using the right procedure when a fault occurs and providing qualified, detailed
information about the state of the PCS 7 plant to service experts
Operating manual
Scenarios during ongoing operation of a plant (including checklist)

Compendium Part D Operation
and Maintenance
Maintenance
Operating manual
Definition and description of test points for the hardware installation of process-related
production facilities.

Compendium Part E Hardware
Installation
Expansion and upgrading

Operation and maintenance
Lines and connection technology

Configuration and design of control cabinets
Earthing, potential equalization and lightning protection
Bus lines

17
Documentation on commissioning, operation, diagnostics and servicing
Documentation
Content
Manuals for the automation

system S7-400H/FH
Commissioning
Manuals on CPs and FMs

(S7400, S7300)
Diagnostics
Maintenance
Manuals for ET 200 components
Commissioning
ET 200M
Diagnostics
ET 200S
Maintenance
ET 200SP
ET 200iSP
ET 200pro
Manuals for additional DP
components:
Diagnostic repeaters
Commissioning
Diagnostics
PA Link
Y-Link
FF Link
DP/AS-i-Link
Manual Programming with STEP
18
Hardware diagnostics and troubleshooting

Index
C
Commissioning
Documentation, 17
D
Diagnostics
Documentation, 17
Documentation
Access options, 5
Commissioning, 17
Diagnostics, 17
for planning and configuration, 5
Operation, 17
Planning phase, 9
Realization phase, 11
Service, 17
O
Operation
Documentation, 17
P
Planning phase
Documentation, 9
R
Realization phase
Documentation, 11
S
Service
Documentation, 17

19

PCS 7 - Documentation

Uploaded by

Copyright:

Available Formats

PCS 7 - Documentation

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

PCS 7 - Documentation

Uploaded by

Copyright:

Available Formats

SIMATIC

Process Control System PCS 7

Valid for PCS 7 as of V8.1

Options for Accessing

Documentation for the

Documentation for the

Proper use of Siemens products

Copyright Siemens AG 2014.

Options for Accessing Documentation.........................................................................................................5

Documentation for the Planning Phase........................................................................................................9

Documentation for the Realization Phase..................................................................................................11

Documentation on commissioning, operation, diagnostics and servicing..................................................17

PCS 7 Documentation (V8.1)

Options for Accessing Documentation

PCS 7 Documentation (V8.1)

Options for Accessing Documentation

PCS 7 Documentation (V8.1)

Options for Accessing Documentation

In the section "Manuals for SIMATIC PCS 7 ..."

PCS 7 Documentation (V8.1)

Documentation for the Planning Phase

Information about the range of services

Standard catalog for system components of a PCS 7 plant

Standard catalog for technological components for SIMATIC PCS 7

Standard catalog for add-ons for SIMATIC PCS 7

Products for automation and drive engineering - interactive catalog CA 01 (DVD)

PCS 7 Engineering System

Section "Engineering system":

Comprehensive overview of PC configurations for engineering and operator control and

Process Safety including two checklists

PCS 7 Documentation (V8.1)

Documentation for the Planning Phase

Process Control System PCS 7;

Security Concept PCS 7 and

Guidelines for planning IT security in automation technology

Process Control System PCS 7; Physical security measures

List of modules released for PCS 7 versions

Function manual PCS 7 Time

Support for planning time synchronization in a PCS 7 plant

Used for data import and for bulk processing

Advanced Engineering System

PCS 7 Documentation (V8.1)

Documentation for the Realization Phase

PCS 7 What's new?

Compact summary of the new or changed features in PCS 7 in comparison to previous

Whitepaper Security Concept

Assembling components and systems

In the section "Configuration of PCS 7 Plants":

PCS 7 Documentation (V8.1)

Documentation for the Realization Phase

Application for data import and bulk processing

Advanced Engineering System

Generation of control modules from signal lists

Function manual Time

Instructions for configuration and parameter assignment of time synchronization

Manuals for the automation

Instructions for configuring automation systems

System manual CPU 410-5H

Instructions for configuring the AS 410 automation system

Manuals for S7-300 I/O